| Age | Commit message (Collapse) | Author |
|---|
|
Prepare for extending the block device ring to allow request
specific fields, by moving the request specific fields for
reads, writes and barrier requests to a union member.
Acked-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Owen Smith <owen.smith@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/jkirsher/net-next-2.6
|
|
We have to use cfg->fc_scope not the final nh_scope value.
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently will ignore prefixes when creating DAPM controls. Since currently
all control creation goes through snd_soc_cnew() we can fix this by factoring
the prefixing into that function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
When multi component systems use DAIless amplifiers which require clocking
configuration it is at best hard to use the current clocking API as this
requires a DAI even though the device may not even have one. Address this
by adding set_sysclk() and set_pll() operations and APIs for CODECs.
In order to avoid issues with devices which could be used either with or
without DAIs make the DAI variants call through to their CODEC counterparts
if there is no DAI specific operation. Converting over entirely would create
problems for multi-DAI devices which offer per-DAI clocking setup.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Allow a slight simplification of CODEC drivers by allowing DAPM routes and
widgets to be provided in a table. They will be instantiated at the end of
CODEC probe.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Put x86 entry code into a separate link section: .entry.text.
Separating the entry text section seems to have performance
benefits - caused by more efficient instruction cache usage.
Running hackbench with perf stat --repeat showed that the change
compresses the icache footprint. The icache load miss rate went
down by about 15%:
before patch:
19417627 L1-icache-load-misses ( +- 0.147% )
after patch:
16490788 L1-icache-load-misses ( +- 0.180% )
The motivation of the patch was to fix a particular kprobes
bug that relates to the entry text section, the performance
advantage was discovered accidentally.
Whole perf output follows:
- results for current tip tree:
Performance counter stats for './hackbench/hackbench 10' (500 runs):
19417627 L1-icache-load-misses ( +- 0.147% )
2676914223 instructions # 0.497 IPC ( +- 0.079% )
5389516026 cycles ( +- 0.144% )
0.206267711 seconds time elapsed ( +- 0.138% )
- results for current tip tree with the patch applied:
Performance counter stats for './hackbench/hackbench 10' (500 runs):
16490788 L1-icache-load-misses ( +- 0.180% )
2717734941 instructions # 0.502 IPC ( +- 0.079% )
5414756975 cycles ( +- 0.148% )
0.206747566 seconds time elapsed ( +- 0.137% )
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: masami.hiramatsu.pt@hitachi.com
Cc: ananth@in.ibm.com
Cc: davem@davemloft.net
Cc: 2nddept-manager@sdl.hitachi.co.jp
LKML-Reference: <20110307181039.GB15197@jolsa.redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Merge reason: Merge latest fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
In complex subsystems like mac80211 structures can contain several
timers and work structs, so identifying a specific instance from the
call trace and object type output of debugobjects can be hard.
Allow the subsystems which support debugobjects to provide a hint
function. This function returns a pointer to a kernel address
(preferrably the objects callback function) which is printed along
with the debugobjects type.
Add hint methods for timer_list, work_struct and hrtimer.
[ tglx: Massaged changelog, made it compile ]
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
LKML-Reference: <20110307085809.GA9334@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Provide the LEB offset information in the UBI device information data
structure. This piece of information is required by UBIFS to find out
what are the LEB offsets which are aligned to the max. write size.
If LEB offset not aligned to max. write size, then UBIFS has to take
this into account to write more optimally.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
Incorporate MTD write buffer size into UBI device information
because UBIFS needs this field. UBI does not use it ATM, just
provides to upper layers in 'struct ubi_device_info'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
|
|
The block integrity subsystem no longer uses the bio_vec slabs so this
code can safely be compiled in.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
a) struct inode is not going to be freed under ->d_compare();
however, the thing PROC_I(inode)->sysctl points to just might.
Fortunately, it's enough to make freeing that sucker delayed,
provided that we don't step on its ->unregistering, clear
the pointer to it in PROC_I(inode) before dropping the reference
and check if it's NULL in ->d_compare().
b) I'm not sure that we *can* walk into NULL inode here (we recheck
dentry->seq between verifying that it's still hashed / fetching
dentry->d_inode and passing it to ->d_compare() and there's no
negative hashed dentries in /proc/sys/*), but if we can walk into
that, we really should not have ->d_compare() return 0 on it!
Said that, I really suspect that this check can be simply killed.
Nick?
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
This records the number of used blocks per checkpoint in each
checkpoint entry of cpfile. Even though userland tools can get the
block count via nilfs_get_cpinfo ioctl, it was not updated by the
nilfs2 kernel code. This fixes the issue and makes it available for
userland tools to calculate used amount per checkpoint.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Jiro SEKIBA <jir@unicus.jp>
|
|
This is a similar change to those in ext2/ext3 codebase (commit
40a063f6691ce937 and a4ae3094869f18e2, respectively).
The addition of 64k block capability in the rec_len_from_disk and
rec_len_to_disk functions added a bit of math overhead which slows
down file create workloads needlessly when the architecture cannot
even support 64k blocks. This will cut the corner.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
|
|
Replaces uses of own inode flags (i.e. NILFS_SECRM_FL, NILFS_UNRM_FL,
NILFS_COMPR_FL, and so forth) with common inode flags, and removes the
own flag declarations.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
|
|
When doing output route lookups, we have to select the source address
if the user has not specified an explicit one.
First, if the route has an explicit preferred source address
specified, then we use that.
Otherwise we search the route's outgoing interface for a suitable
address.
This search can be precomputed and cached at route insertion time.
The only missing part is that we have to refresh this precomputed
value any time addresses are added or removed from the interface, and
this is accomplished by fib_update_nh_saddrs().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Fiber Channel over Ethernet (FCoE) Direct Data Placement (DDP) can also be
used for FCoE target, where the DDP used for read I/O on an initiator can be
used on an FCoE target to speed up the write I/O to the target from the initiator.
The added ndo_fcoe_ddp_target() works in the similar way as the existing
ndo_fcoe_ddp_setup() to allow the underlying hardware set up the DDP context
accordingly when it gets called from the FCoE target implementation on top
the existing Open-FCoE fcoe/libfc protocol stack so without losing the ability
to provide DDP for read I/O as an initiator, it can also provide DDP offload
to the write I/O coming from the initiator as a target.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
|
|
Add a keyctl op (KEYCTL_INSTANTIATE_IOV) that is like KEYCTL_INSTANTIATE, but
takes an iovec array and concatenates the data in-kernel into one buffer.
Since the KEYCTL_INSTANTIATE copies the data anyway, this isn't too much of a
problem.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Add a new keyctl op to reject a key with a specified error code. This works
much the same as negating a key, and so keyctl_negate_key() is made a special
case of keyctl_reject_key(). The difference is that keyctl_negate_key()
selects ENOKEY as the error to be reported.
Typically the key would be rejected with EKEYEXPIRED, EKEYREVOKED or
EKEYREJECTED, but this is not mandatory.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Add a key type operation to permit the key type to vet the description of a new
key that key_alloc() is about to allocate. The operation may reject the
description if it wishes with an error of its choosing. If it does this, the
key will not be allocated.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
Add an RCU payload dereference macro as this seems to be a common piece of code
amongst key types that use RCU referenced payloads.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
|
|
|
|
This patch implements PRUSS (Programmable Real-time Unit Sub System)
UIO driver which exports SOC resources associated with PRUSS like
I/O, memories and IRQs to user space. PRUSS is dual 32-bit RISC
processors which is efficient in performing embedded tasks that
require manipulation of packed memory mapped data structures and
handling system events that have tight real time constraints. This
driver is currently supported on Texas Instruments DA850, AM18xx and
OMAP-L138 devices.
For example, PRUSS runs firmware for real-time critical industrial
communication data link layer and communicates with application stack
running in user space via shared memory and IRQs.
Signed-off-by: Pratheesh Gangadhar <pratheesh@ti.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans J. Koch <hjk@hansjkoch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This allows any caller to be prefaced by any specific
pr_fmt to better identify which device driver is using
this function inappropriately.
Add terminating newline.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This driver is used across all MSM SoCs. Hence give a generic name.
All Functions and strutures are also using "msm_otg" as prefix.
Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The hcd->state variable is a disaster. It's not clearly owned by
either usbcore or the host controller drivers, and they both change it
from time to time, potentially stepping on each other's toes. It's
not protected by any locks. And there's no mechanism to prevent it
from going through an invalid transition.
This patch (as1451) takes a first step toward fixing these problems.
As it turns out, usbcore uses hcd->state for essentially only two
things: checking whether the controller's root hub is running and
checking whether the controller has died. Therefore the patch adds
two new atomic bitflags to the hcd structure, to store these pieces of
information. The new flags are used only by usbcore, and a private
spinlock prevents invalid combinations (a dead controller's root hub
cannot be running).
The patch does not change the places where usbcore sets hcd->state,
since HCDs may depend on them. Furthermore, there is one place in
usb_hcd_irq() where usbcore still must use hcd->state: An HCD's
interrupt handler can implicitly indicate that the controller died by
setting hcd->state to HC_STATE_HALT. Nevertheless, the new code is a
big improvement over the current code.
The patch makes one other change. The hcd_bus_suspend() and
hcd_bus_resume() routines now check first whether the host controller
has died; if it has then they return immediately without calling the
HCD's bus_suspend or bus_resume methods.
This fixes the major problem reported in Bugzilla #29902: The system
fails to suspend after a host controller dies during system resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alex Terekhov <a.terekhov@gmail.com>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
This driver supports UART-DM HW on MSM platforms. It uses the on
chip DMA to drive data transfers and has optional support for UART
power management independent of Linux suspend/resume and wakeup
from Rx.
The driver was originally developed by Google. It is functionally
equivalent to the version available at:
http://android.git.kernel.org/?p=kernel/experimental.git
the differences being:
1) Remove wakelocks and change unsupported DMA API.
2) Replace clock selection register codes by macros.
3) Fix checkpatch errors and add inline documentation.
4) Add runtime PM hooks for active power state transitions.
5) Handle error path and cleanup resources if required.
CC: Nick Pelly <npelly@google.com>
Signed-off-by: Sankalp Bose <sankalpb@codeaurora.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Msize or Burst Size is peripheral dependent in case of prep_slave_sg and
cyclic_prep transfers, and in case of memcpy transfers it is platform dependent.
So msize configuration must come from platform data.
Also some peripherals (ex: JPEG), need to be flow controller for dma transfers,
so this information in case of slave_sg & cyclic_prep transfers must come from
platform data.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
src_master & dest_master don't required u32 as they have values limited to u8
only. Also their description is missing from doc style comment. This patch
fixes above mentioned issues.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In Synopsys designware, channel priority is programmable. This patch adds
support for passing channel priority through platform data. By default Ascending
channel priority will be followed, i.e. channel 0 will get highest priority and
channel 7 will get lowest.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
In SPEAr Platform channels 4-7 have more Fifo depth. So we must get better
channel first. This patch introduces concept of channel allocation order in
dw_dmac. If user doesn't pass anything or 0, than normal (ascending) channel
allocation will follow, else channels will be allocated in descending order.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: no .snap inside of snapped namespace
libceph: fix msgr standby handling
libceph: fix msgr keepalive flag
libceph: fix msgr backoff
libceph: retry after authorization failure
libceph: fix handling of short returns from get_user_pages
ceph: do not clear I_COMPLETE from d_release
ceph: do not set I_COMPLETE
Revert "ceph: keep reference to parent inode on ceph_dentry"
|
|
This removes the implementation of the big kernel lock,
at last. A lot of people have worked on this in the
past, I so the credit for this patch should be with
everyone who participated in the hunt.
The names on the Cc list are the people that were the
most active in this, according to the recorded git
history, in alphabetical order.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: Alessio Igor Bogani <abogani@texware.it>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andrew Hendry <andrew.hendry@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Jan Blunck <jblunck@infradead.org>
Cc: John Kacur <jkacur@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Oliver Neukum <oliver@neukum.org>
Cc: Paul Menage <menage@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The only necessary parts are the src/dst addresses, the
interface indexes, the TOS, and the mark.
The rest is unnecessary bloat, which amounts to nearly
50 bytes on 64-bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a alloc_page_vma_node that allows passing the "local" node in. Used
in a followon patch.
Acked-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently alloc_pages_vma() always uses the local node as policy node for
the LOCAL policy. Pass this node down as an argument instead.
No behaviour change from this patch, but will be needed for followons.
Acked-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ssh://master.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
|
There was some broken keepalive code using a dead variable. Shift to using
the proper bit flag.
Signed-off-by: Sage Weil <sage@newdream.net>
|
|
With commit f363e45f we replaced a bunch of hacky workqueue mutual
exclusion logic with the WQ_NON_REENTRANT flag. One pieces of fallout is
that the exponential backoff breaks in certain cases:
* con_work attempts to connect.
* we get an immediate failure, and the socket state change handler queues
immediate work.
* con_work calls con_fault, we decide to back off, but can't queue delayed
work.
In this case, we add a BACKOFF bit to make con_work reschedule delayed work
next time it runs (which should be immediately).
Signed-off-by: Sage Weil <sage@newdream.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/padovan/bluetooth-next-2.6
|
|
This patch adds support for tlv320aic3205 and tlv320aic3254 codecs.
It doesn't include miniDSP support for aic3254.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This merge creates two set of conflicts. One is simple context
conflicts caused by removal of throtl_scheduled_delayed_work() in
for-linus and removal of throtl_shutdown_timer_wq() in
for-2.6.39/core.
The other is caused by commit 255bb490c8 (block: blk-flush shouldn't
call directly into q->request_fn() __blk_run_queue()) in for-linus
crashing with FLUSH reimplementation in for-2.6.39/core. The conflict
isn't trivial but the resolution is straight-forward.
* __blk_run_queue() calls in flush_end_io() and flush_data_end_io()
should be called with @force_kblockd set to %true.
* elv_insert() in blk_kick_flush() should use
%ELEVATOR_INSERT_REQUEUE.
Both changes are to avoid invoking ->request_fn() directly from
request completion path and closely match the changes in the commit
255bb490c8.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
They are only used inside kernel/ptrace.c, and have been for a long
time. We don't want to go back to the bad-old-days when architectures
did things on their own, so make them static and private.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change logs against Andi's original version:
- Extends perf_event_attr:config to config{,1,2} (Peter Zijlstra)
- Fixed a major event scheduling issue. There cannot be a ref++ on an
event that has already done ref++ once and without calling
put_constraint() in between. (Stephane Eranian)
- Use thread_cpumask for percore allocation. (Lin Ming)
- Use MSR names in the extra reg lists. (Lin Ming)
- Remove redundant "c = NULL" in intel_percore_constraints
- Fix comment of perf_event_attr::config1
Intel Nehalem/Westmere have a special OFFCORE_RESPONSE event
that can be used to monitor any offcore accesses from a core.
This is a very useful event for various tunings, and it's
also needed to implement the generic LLC-* events correctly.
Unfortunately this event requires programming a mask in a separate
register. And worse this separate register is per core, not per
CPU thread.
This patch:
- Teaches perf_events that OFFCORE_RESPONSE needs extra parameters.
The extra parameters are passed by user space in the
perf_event_attr::config1 field.
- Adds support to the Intel perf_event core to schedule per
core resources. This adds fairly generic infrastructure that
can be also used for other per core resources.
The basic code has is patterned after the similar AMD northbridge
constraints code.
Thanks to Stephane Eranian who pointed out some problems
in the original version and suggested improvements.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1299119690-13991-2-git-send-email-ming.m.lin@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Merge reason: Add fixes before applying dependent patches.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Merge reason: Pick up updates before queueing up dependent patches.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
