| Age | Commit message (Collapse) | Author |
|---|
|
Receive Flow Steering is a nice solution but suffers from
hash collisions when a mix of connected and unconnected traffic
is received on the host, when flow hash table is populated.
Also, clearing flow in inet_release() makes RFS not very good
for short lived flows, as many packets can follow close().
(FIN , ACK packets, ...)
This patch extends the information stored into global hash table
to not only include cpu number, but upper part of the hash value.
I use a 32bit value, and dynamically split it in two parts.
For host with less than 64 possible cpus, this gives 6 bits for the
cpu number, and 26 (32-6) bits for the upper part of the hash.
Since hash bucket selection use low order bits of the hash, we have
a full hash match, if /proc/sys/net/core/rps_sock_flow_entries is big
enough.
If the hash found in flow table does not match, we fallback to RPS (if
it is enabled for the rxqueue).
This means that a packet for an non connected flow can avoid the
IPI through a unrelated/victim CPU.
This also means we no longer have to clear the table at socket
close time, and this helps short lived flows performance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove trailing underscore.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that in state FIN_WAIT2 or TIME_WAIT, where the connection is
represented by a tcp_timewait_sock, we rate limit dupacks in response
to incoming packets (a) with TCP timestamps that fail PAWS checks, or
(b) with sequence numbers that are out of the acceptable window.
We do not send a dupack in response to out-of-window packets if it has
been less than sysctl_tcp_invalid_ratelimit (default 500ms) since we
last sent a dupack in response to an out-of-window packet.
Reported-by: Avery Fay <avery@mixpanel.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that in state ESTABLISHED, where the connection is represented
by a tcp_sock, we rate limit dupacks in response to incoming packets
(a) with TCP timestamps that fail PAWS checks, or (b) with sequence
numbers or ACK numbers that are out of the acceptable window.
We do not send a dupack in response to out-of-window packets if it has
been less than sysctl_tcp_invalid_ratelimit (default 500ms) since we
last sent a dupack in response to an out-of-window packet.
There is already a similar (although global) rate-limiting mechanism
for "challenge ACKs". When deciding whether to send a challence ACK,
we first consult the new per-connection rate limit, and then the
global rate limit.
Reported-by: Avery Fay <avery@mixpanel.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the SYN_RECV state, where the TCP connection is represented by
tcp_request_sock, we now rate-limit SYNACKs in response to a client's
retransmitted SYNs: we do not send a SYNACK in response to client SYN
if it has been less than sysctl_tcp_invalid_ratelimit (default 500ms)
since we last sent a SYNACK in response to a client's retransmitted
SYN.
This allows the vast majority of legitimate client connections to
proceed unimpeded, even for the most aggressive platforms, iOS and
MacOS, which actually retransmit SYNs 1-second intervals for several
times in a row. They use SYN RTO timeouts following the progression:
1,1,1,1,1,2,4,8,16,32.
Reported-by: Avery Fay <avery@mixpanel.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Helpers for mitigating ACK loops by rate-limiting dupacks sent in
response to incoming out-of-window packets.
This patch includes:
- rate-limiting logic
- sysctl to control how often we allow dupacks to out-of-window packets
- SNMP counter for cases where we rate-limited our dupack sending
The rate-limiting logic in this patch decides to not send dupacks in
response to out-of-window segments if (a) they are SYNs or pure ACKs
and (b) the remote endpoint is sending them faster than the configured
rate limit.
We rate-limit our responses rather than blocking them entirely or
resetting the connection, because legitimate connections can rely on
dupacks in response to some out-of-window segments. For example, zero
window probes are typically sent with a sequence number that is below
the current window, and ZWPs thus expect to thus elicit a dupack in
response.
We allow dupacks in response to TCP segments with data, because these
may be spurious retransmissions for which the remote endpoint wants to
receive DSACKs. This is safe because segments with data can't
realistically be part of ACK loops, which by their nature consist of
each side sending pure/data-less ACKs to each other.
The dupack interval is controlled by a new sysctl knob,
tcp_invalid_ratelimit, given in milliseconds, in case an administrator
needs to dial this upward in the face of a high-rate DoS attack. The
name and units are chosen to be analogous to the existing analogous
knob for ICMP, icmp_ratelimit.
The default value for tcp_invalid_ratelimit is 500ms, which allows at
most one such dupack per 500ms. This is chosen to be 2x faster than
the 1-second minimum RTO interval allowed by RFC 6298 (section 2, rule
2.4). We allow the extra 2x factor because network delay variations
can cause packets sent at 1 second intervals to be compressed and
arrive much closer.
Reported-by: Avery Fay <avery@mixpanel.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OVS userspace already probes the openvswitch kernel module for
OVS_ACTION_ATTR_SET_MASKED support. This patch adds the kernel module
implementation of masked set actions.
The existing set action sets many fields at once. When only a subset
of the IP header fields, for example, should be modified, all the IP
fields need to be exact matched so that the other field values can be
copied to the set action. A masked set action allows modification of
an arbitrary subset of the supported header bits without requiring the
rest to be matched.
Masked set action is now supported for all writeable key types, except
for the tunnel key. The set tunnel action is an exception as any
input tunnel info is cleared before action processing starts, so there
is no tunnel info to mask.
The kernel module converts all (non-tunnel) set actions to masked set
actions. This makes action processing more uniform, and results in
less branching and duplicating the action processing code. When
returning actions to userspace, the fully masked set actions are
converted back to normal set actions. We use a kernel internal action
code to be able to tell the userspace provided and converted masked
set actions apart.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
NFC: 3.20 second pull request
This is the second NFC pull request for 3.20.
It brings:
- NCI NFCEE (NFC Execution Environment, typically an embedded or
external secure element) discovery and enabling/disabling support.
In order to communicate with an NFCEE, we also added NCI's logical
connections support to the NCI stack.
- HCI over NCI protocol support. Some secure elements only understand
HCI and thus we need to send them HCI frames when they're part of
an NCI chipset.
- NFC_EVT_TRANSACTION userspace API addition. Whenever an application
running on a secure element needs to notify its host counterpart,
we send an NFC_EVENT_SE_TRANSACTION event to userspace through the
NFC netlink socket.
- Secure element and HCI transaction event support for the st21nfcb
chipset.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'spi/topic/qup', 'spi/topic/rockchip' and 'spi/topic/samsung' into spi-next
|
|
'spi/topic/inline', 'spi/topic/meson' and 'spi/topic/mxs' into spi-next
|
|
'spi/topic/fsl', 'spi/topic/fsl-dspi' and 'spi/topic/gpio' into spi-next
|
|
|
|
'regulator/topic/mode', 'regulator/topic/mt6397', 'regulator/topic/pfuze100' and 'regulator/topic/qcom-rpm' into regulator-next
|
|
'regulator/topic/da9211' and 'regulator/topic/fan53555' into regulator-next
|
|
|
|
regulator: Fix !REGULATOR builds of systems using system suspend calls
The system suspend calls (used to synchronize between system suspend of
the CPU and it's PMIC) are called from board code but not stubbed when
regulator is disabled causing build failures in such cases. This patch
fixes those build failures.
# gpg: Signature made Thu 05 Feb 2015 05:10:43 HKT using RSA key ID 5D5487D0
# gpg: WARNING: digest algorithm MD5 is deprecated
# gpg: please see http://www.gnupg.org/faq/weak-digest-algos.html for more information
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: key AF88CD16: no public key for trusted key - skipped
# gpg: key AF88CD16 marked as ultimately trusted
# gpg: key 5621E907: no public key for trusted key - skipped
# gpg: key 5621E907 marked as ultimately trusted
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
|
|
'regmap/topic/smbus' into regmap-next
|
|
When taking a CPU down for suspend and resume, a tracepoint may be called
when the CPU has been designated offline. As tracepoints require RCU for
protection, they must not be called if the current CPU is offline.
Unfortunately, trace_tlb_flush() is called in this scenario as was noted
by LOCKDEP:
...
Disabling non-boot CPUs ...
intel_pstate CPU 1 exiting
===============================
smpboot: CPU 1 didn't die...
[ INFO: suspicious RCU usage. ]
3.19.0-rc7-next-20150204.1-iniza-small #1 Not tainted
-------------------------------
include/trace/events/tlb.h:35 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from offline CPU!
rcu_scheduler_active = 1, debug_locks = 0
no locks held by swapper/1/0.
stack backtrace:
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 3.19.0-rc7-next-20150204.1-iniza-small #1
Hardware name: SAMSUNG ELECTRONICS CO., LTD. 530U3BI/530U4BI/530U4BH/530U3BI/530U4BI/530U4BH, BIOS 13XK 03/28/2013
0000000000000001 ffff88011a44fe18 ffffffff817e370d 0000000000000011
ffff88011a448290 ffff88011a44fe48 ffffffff810d6847 ffff8800c66b9600
0000000000000001 ffff88011a44c000 ffffffff81cb3900 ffff88011a44fe78
Call Trace:
[<ffffffff817e370d>] dump_stack+0x4c/0x65
[<ffffffff810d6847>] lockdep_rcu_suspicious+0xe7/0x120
[<ffffffff810b71a5>] idle_task_exit+0x205/0x2c0
[<ffffffff81054c4e>] play_dead_common+0xe/0x50
[<ffffffff81054ca5>] native_play_dead+0x15/0x140
[<ffffffff8102963f>] arch_cpu_idle_dead+0xf/0x20
[<ffffffff810cd89e>] cpu_startup_entry+0x37e/0x580
[<ffffffff81053e20>] start_secondary+0x140/0x150
intel_pstate CPU 2 exiting
...
By converting the tlb_flush tracepoint to a TRACE_EVENT_CONDITION where the
condition is cpu_online(smp_processor_id()), we can avoid calling RCU protected
code when the CPU is offline.
Link: http://lkml.kernel.org/r/CA+icZUUGiGDoL5NU8RuxKzFjoLjEKRtUWx=JB8B9a0EQv-eGzQ@mail.gmail.com
Cc: stable@vger.kernel.org # 3.17+
Fixes: d17d8f9dedb9 "x86/mm: Add tracepoints for TLB flushes"
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Suggested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Hansen <dave@sr71.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The trace_tlb_flush() tracepoint can be called when a CPU is going offline.
When a CPU is offline, RCU is no longer watching that CPU and since the
tracepoint is protected by RCU, it must not be called. To prevent the
tlb_flush tracepoint from being called when the CPU is offline, it was
converted to a TRACE_EVENT_CONDITION where the condition checks if the
CPU is online before calling the tracepoint.
Unfortunately, this was not enough to stop lockdep from complaining about
it. Even though the RCU protected code of the tracepoint will never be
called, the condition is hidden within the tracepoint, and even though the
condition prevents RCU code from being called, the lockdep checks are
outside the tracepoint (this is to test tracepoints even when they are not
enabled).
Even though tracepoints should be checked to be RCU safe when they are not
enabled, the condition should still be considered when checking RCU.
Link: http://lkml.kernel.org/r/CA+icZUUGiGDoL5NU8RuxKzFjoLjEKRtUWx=JB8B9a0EQv-eGzQ@mail.gmail.com
Fixes: 3a630178fd5f "tracing: generate RCU warnings even when tracepoints are disabled"
Cc: stable@vger.kernel.org # 3.18+
Acked-by: Dave Hansen <dave@sr71.net>
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull one more infiniband revert from Roland Dreier:
"One more last-second RDMA change for 3.19: Yann realized that the
previous revert of new userspace ABI did not go far enough, and we're
still exposing a change that we don't want. Revert even closer to
3.18 interface to make sure we get things right in the long run"
Yann Droneaud pipes up:
"I hope this could go in v3.19 as, at this stage, we don't want to
expose any bits of this ABI in a released kernel"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
Revert "IB/core: Add support for extended query device caps"
|
|
* pci/misc:
PCI: Add pci_device_to_OF_node() stub for !CONFIG_OF
|
|
This is the last missing piece to get a kernel booting to a prompt in qemu-cris.
Signed-off-by: Niklas Cassel <nks@flawful.org>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fixes from Ingo Molnar:
"Misc fixes"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/deadline: Fix deadline parameter modification handling
sched/wait: Remove might_sleep() from wait_event_cmd()
sched: Fix crash if cpuset_cpumask_can_shrink() is passed an empty cpumask
sched/fair: Avoid using uninitialized variable in preferred_group_nid()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Hopefully the final pull request for 3.19: this ended up with a
slightly higher volume than wished, but I put them all as they are
either stable or 3.19 regression fixes.
Most of commits are from ASoC, and have been stewed for a while in
linux-next. The only change in the common code is the regression
fixes for ASoC AC97 stuff wrt device registrations. The rest are
device-specific, mostly small fixes in various ASoC drivers and ak411x
on ice1724 boards"
* tag 'sound-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: Intel: fix sst firmware path for cht-bsw-rt5672
ARM: dts: Fix I2S1, I2S2 compatible for exynos4 SoCs
ASoC: sgtl5000: add delay before first I2C access
MAINTAINERS: ASoC: add maintainer for Intel BDW/HSW ASoC driver
ASoC: atmel_ssc_dai: fix the setting for DSP mode
ASoC: sgtl5000: Use shift mask when setting codec mode
ASoC: tlv320aic3x: Fix data delay configuration
ALSA: ak411x: Fix stall in work callback
ASoC: Intel: Used lock version to update shim registers
ASoC: wm8731: init mutex in i2c init path
ASoC: atmel_ssc_dai: fix start event for I2S mode
ASoC: rt5640: Add RT5642 ACPI ID for Intel Baytrail
ASoC: wm97xx: Reset AC'97 device before registering it
ASoC: Add support for allocating AC'97 device before registering it
|
|
This patch introduces a new module parameter for the KVM module; when it
is present, KVM attempts a bit of polling on every HLT before scheduling
itself out via kvm_vcpu_block.
This parameter helps a lot for latency-bound workloads---in particular
I tested it with O_DSYNC writes with a battery-backed disk in the host.
In this case, writes are fast (because the data doesn't have to go all
the way to the platters) but they cannot be merged by either the host or
the guest. KVM's performance here is usually around 30% of bare metal,
or 50% if you use cache=directsync or cache=writethrough (these
parameters avoid that the guest sends pointless flush requests, and
at the same time they are not slow because of the battery-backed cache).
The bad performance happens because on every halt the host CPU decides
to halt itself too. When the interrupt comes, the vCPU thread is then
migrated to a new physical CPU, and in general the latency is horrible
because the vCPU thread has to be scheduled back in.
With this patch performance reaches 60-65% of bare metal and, more
important, 99% of what you get if you use idle=poll in the guest. This
means that the tunable gets rid of this particular bottleneck, and more
work can be done to improve performance in the kernel or QEMU.
Of course there is some price to pay; every time an otherwise idle vCPUs
is interrupted by an interrupt, it will poll unnecessarily and thus
impose a little load on the host. The above results were obtained with
a mostly random value of the parameter (500000), and the load was around
1.5-2.5% CPU usage on one of the host's core for each idle guest vCPU.
The patch also adds a new stat, /sys/kernel/debug/kvm/halt_successful_poll,
that can be used to tune the parameter. It counts how many HLT
instructions received an interrupt during the polling period; each
successful poll avoids that Linux schedules the VCPU thread out and back
in, and may also avoid a likely trip to C1 and back for the physical CPU.
While the VM is idle, a Linux 4 VCPU VM halts around 10 times per second.
Of these halts, almost all are failed polls. During the benchmark,
instead, basically all halts end within the polling period, except a more
or less constant stream of 50 per second coming from vCPUs that are not
running the benchmark. The wasted time is thus very low. Things may
be slightly different for Windows VMs, which have a ~10 ms timer tick.
The effect is also visible on Marcelo's recently-introduced latency
test for the TSC deadline timer. Though of course a non-RT kernel has
awful latency bounds, the latency of the timer is around 8000-10000 clock
cycles compared to 20000-120000 without setting halt_poll_ns. For the TSC
deadline timer, thus, the effect is both a smaller average latency and
a smaller variance.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers
Merge "Samsung CPUIdle updates for v3.20" from Kukjin Kim:
- adds coupled cpuidle support for exynos4210
: fix for Exynos platform PM code preparing it for the coupled
cpuidle support and adds coupled cpuidle AFTR mode on exynos4210
Note this is mostrly based on earlier cpuidle-exynos4210 driver
from Daniel Lezcano and Bart updated.
* tag 'samsung-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
For assigning sysfs entries for a card device from the driver,
introduce a new helper function, snd_card_add_dev_attr(). In this
way, we can avoid the possible race between the device registration
and the sysfs addition / removal.
The driver can pass a new attribute group to add freely. This has to
be called before snd_card_register().
Currently, up to two extra groups can be added. More than that, it'll
return an error.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
While commit 7e36ef8205ff ("IB/core: Temporarily disable
ex_query_device uverb") is correct as it makes the extended
QUERY_DEVICE uverb (which came as part of commit 5a77abf9a97a
("IB/core: Add support for extended query device caps") and commit
860f10a799c8 ("IB/core: Add flags for on demand paging support")) not
available to userspace, it doesn't address the initial issue regarding
ib_copy_to_udata() [1][2].
Additionally, further discussions around this new uverb seems to
conclude it would require a different data structure than the one
currently described in <rdma/ib_user_verbs.h> [3].
Both of these issues require a revert of the changes, so this patch
partially reverts commit 8cdd312cfed7 ("IB/mlx5: Implement the ODP
capability query verb") and commit 860f10a799c8 ("IB/core: Add flags
for on demand paging support") and fully reverts commit 5a77abf9a97a
("IB/core: Add support for extended query device caps").
[1] "Re: [PATCH v3 06/17] IB/core: Add support for extended query device caps"
http://mid.gmane.org/1418733236.2779.26.camel@opteya.com
[2] "Re: [PATCH] IB/core: Temporarily disable ex_query_device uverb"
http://mid.gmane.org/1423067503.3030.83.camel@opteya.com
[3] "RE: [PATCH v1 1/5] IB/uverbs: ex_query_device: answer must not depend on request's comp_mask"
http://mid.gmane.org/2807E5FD2F6FDA4886F6618EAC48510E0CC12C30@CRSMSX101.amr.corp.intel.com
Cc: Eli Cohen <eli@mellanox.com>
Cc: Haggai Eran <haggaie@mellanox.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: third (and last) batch of dts updates for 3.20" from
Heiko Stübner:
Change are regulator nodes for the cpu and gpu regulators on the act8846
variant of the rk3288-evb and the setting of a clock for the watchdog.
Also the lcd and hdmi controllers on both the firefly and the evb get
enabled and let us now boot into fbcon console sucessfully.
* tag 'v3.20-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
ARM: dts: rockchip: housekeeping off i2c0 on rk3288-evb boards
ARM: dts: rockchip: add cpu and gpu regulators to rk3288-evb-act8846
ARM: dts: rockchip: add rk3288 watchdog clock
clk: rockchip: add id for watchdog pclk on rk3288
clk: rockchip: add clock IDs for the PVTM clocks
clk: rockchip: add clock ID for usbphy480m_src
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
If we're sending an asynchronous layoutreturn, then we need to ensure
that the inode and the super block remain pinned.
Cc: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
|
|
If we're sending an asynchronous layoutcommit, then we need to ensure
that the inode and the super block remain pinned.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
Reviewed-by: Peng Tao <tao.peng@primarydata.com>
|
|
RFC 4429 ("Optimistic DAD") states that optimistic addresses
should be treated as deprecated addresses. From section 2.1:
Unless noted otherwise, components of the IPv6 protocol stack
should treat addresses in the Optimistic state equivalently to
those in the Deprecated state, indicating that the address is
available for use but should not be used if another suitable
address is available.
Optimistic addresses are indeed avoided when other addresses are
available (i.e. at source address selection time), but they have
not heretofore been available for things like explicit bind() and
sendmsg() with struct in6_pktinfo, etc.
This change makes optimistic addresses treated more like
deprecated addresses than tentative ones.
Signed-off-by: Erik Kline <ek@google.com>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: AC'97 fixes
These are rather too large for this late in the release cycle but
they're clear, well understood and have been tested to fix a regression
which was introduced for v3.19. The details are all in Lars' changelog
and they've been cooking in -next for a while, to a large extent out
of conservatism about the size.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.19
A few last minute fixes for v3.19, all driver specific. None of them
stand out particularly - it's all the standard people who are affected
will care stuff.
The Samsung fix is a DT only fix for the audio controller, it's being
merged via the ASoC tree due to process messups (the submitter sent it
at the end of a tangentally related series rather than separately to the
ARM folks) in order to make sure that it gets to people sooner.
|
|
Pull networking fixes from David Miller:
1) Stretch ACKs can kill performance with Reno and CUBIC congestion
control, largely due to LRO and GRO. Fix from Neal Cardwell.
2) Fix userland breakage because we accidently emit zero length netlink
messages from the bridging code. From Roopa Prabhu.
3) Carry handling in generic csum_tcpudp_nofold is broken, fix from
Karl Beldan.
4) Remove bogus dev_set_net() calls from CAIF driver, from Nicolas
Dichtel.
5) Make sure PPP deflation never returns a length greater then the
output buffer, otherwise we overflow and trigger skb_over_panic().
Fix from Florian Westphal.
6) COSA driver needs VIRT_TO_BUS Kconfig dependencies, from Arnd
Bergmann.
7) Don't increase route cached MTU on datagram too big ICMPs. From Li
Wei.
8) Fix error path leaks in nf_tables, from Pablo Neira Ayuso.
9) Fix bitmask handling regression in netlink that broke things like
acpi userland tools. From Pablo Neira Ayuso.
10) Wrong header pointer passed to param_type2af() in SCTP code, from
Saran Maruti Ramanara.
11) Stacked vlans not handled correctly by vlan_get_protocol(), from
Toshiaki Makita.
12) Add missing DMA memory barrier to xgene driver, from Iyappan
Subramanian.
13) Fix crash in rate estimators, from Eric Dumazet.
14) We've been adding various workarounds, one after another, for the
change which added the per-net tcp_sock. It was meant to reduce
socket contention but added lots of problems.
Reduce this instead to a proper per-cpu socket and that rids us of
all the daemons.
From Eric Dumazet.
15) Fix memory corruption and OOPS in mlx4 driver, from Jack
Morgenstein.
16) When we disabled UFO in the virtio_net device, it introduces some
serious performance regressions. The orignal problem was IPV6
fragment ID generation, so fix that properly instead. From Vlad
Yasevich.
17) sr9700 driver build breaks on xtensa because it defines macros with
the same name as those used by the arch code. Use more unique
names. From Chen Gang.
18) Fix endianness in new virio 1.0 mode of the vhost net driver, from
Michael S Tsirkin.
19) Several sysctls were setting the maxlen attribute incorrectly, from
Sasha Levin.
20) Don't accept an FQ scheduler quantum of zero, that leads to crashes.
From Kenneth Klette Jonassen.
21) Fix dumping of non-existing actions in the packet scheduler
classifier. From Ignacy Gawędzki.
22) Return the write work_done value when doing TX work in the qlcnic
driver.
23) ip6gre_err accesses the info field with the wrong endianness, from
Sabrina Dubroca.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
sit: fix some __be16/u16 mismatches
ipv6: fix sparse errors in ip6_make_flowlabel()
net: remove some sparse warnings
flow_keys: n_proto type should be __be16
ip6_gre: fix endianness errors in ip6gre_err
qlcnic: Fix NAPI poll routine for Tx completion
amd-xgbe: Set RSS enablement based on hardware features
amd-xgbe: Adjust for zero-based traffic class count
cls_api.c: Fix dumping of non-existing actions' stats.
pkt_sched: fq: avoid hang when quantum 0
net: rds: use correct size for max unacked packets and bytes
vhost/net: fix up num_buffers endian-ness
gianfar: correct the bad expression while writing bit-pattern
net: usb: sr9700: Use 'SR_' prefix for the common register macros
Revert "drivers/net: Disable UFO through virtio"
Revert "drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets"
ipv6: Select fragment id during UFO segmentation if not set.
xen-netback: stop the guest rx thread after a fatal error
net/mlx4_core: Fix kernel Oops (mem corruption) when working with more than 80 VFs
isdn: off by one in connect_res()
...
|
|
And also remove the unused bdev argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Make use of a new interface provided by iov_iter, backed by
scatter-gather list of iovec, instead of the old interface based on
sg_iovec. Also use iov_iter_advance() instead of manual iteration.
This commit should contain only literal replacements, without
functional changes.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Doug Gilbert <dgilbert@interlog.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
[dpark: add more description in commit message]
Signed-off-by: Dongsu Park <dongsu.park@profitbricks.com>
[hch: fixed to do a deep clone of the iov_iter, and to properly use
the iov_iter direction]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
the current GPE APIs
ACPICA commit 199cad16530a45aea2bec98e528866e20c5927e1
Since whether the GPE should be disabled/enabled/cleared should only be
determined by the GPE driver's state machine:
1. GPE should be disabled if the driver wants to switch to the GPE polling
mode when a GPE storm condition is indicated and should be enabled if
the driver wants to switch back to the GPE interrupt mode when all of
the storm conditions are cleared. The conditions should be protected by
the driver's specific lock.
2. GPE should be enabled if the driver has accepted more than one request
and should be disabled if the driver has completed all of the requests.
The request count should be protected by the driver's specific lock.
3. GPE should be cleared either when the driver is about to handle an edge
triggered GPE or when the driver has completed to handle a level
triggered GPE. The handling code should be protected by the driver's
specific lock.
Thus the GPE enabling/disabling/clearing operations are likely to be
performed with the driver's specific lock held while we currently cannot do
this. This is because:
1. We have the acpi_gbl_gpe_lock held before invoking the GPE driver's
handler. Driver's specific lock is likely to be held inside of the
handler, thus we can see some dead lock issues due to the reversed
locking order or recursive locking. In order to solve such dead lock
issues, we need to unlock the acpi_gbl_gpe_lock before invoking the
handler. BZ 1100.
2. Since GPE disabling/enabling/clearing should be determined by the GPE
driver's state machine, we shouldn't perform such operations inside of
ACPICA for a GPE handler to mess up the driver's state machine. BZ 1101.
Originally this patch includes a logic to flush GPE handlers, it is dropped
due to the following reasons:
1. This is a different issue;
2. Linux OSL has fixed this by flushing SCI in acpi_os_wait_events_complete().
We will pick up this topic when the Linux OSL fix turns out to be not
sufficient.
Note that currently the internal operations and the acpi_gbl_gpe_lock are
also used by ACPI_GPE_DISPATCH_METHOD and ACPI_GPE_DISPATCH_NOTIFY. In
order not to introduce regressions, we add one
ACPI_GPE_DISPATCH_RAW_HANDLER type to be distiguished from
ACPI_GPE_DISPATCH_HANDLER. For which the acpi_gbl_gpe_lock is unlocked before
invoking the GPE handler and the internal enabling/disabling operations are
bypassed to allow drivers to perform them at a proper position using the
GPE APIs and ACPI_GPE_DISPATCH_RAW_HANDLER users should invoke acpi_set_gpe()
instead of acpi_enable_gpe()/acpi_disable_gpe() to bypass the internal GPE
clearing code in acpi_enable_gpe(). Lv Zheng.
Known issues:
1. Edge-triggered GPE lost for frequent enablings
On some buggy silicon platforms, GPE enable line may not be directly
wired to the GPE trigger line. In that case, when GPE enabling is
frequently performed for edge-triggered GPEs, GPE status may stay set
without being triggered.
This patch may maginify this problem as it allows GPE enabling to be
parallel performed during the process the GPEs are handled.
This is an existing issue, because:
1. For task context:
Current ACPI_GPE_DISPATCH_METHOD practices have proven that this
isn't a real issue - we can re-enable edge-triggered GPE in a work
queue where the GPE status bit might already be set.
2. For IRQ context:
This can even happen when the GPE enabling occurs before returning
from the GPE handler and after unlocking the GPE lock.
Thus currently no code is included to protect this.
Link: https://github.com/acpica/acpica/commit/199cad16
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit e06b1624b02dc8317d144e9a6fe9d684c5fa2f90
Version 20150204.
Link: https://github.com/acpica/acpica/commit/e06b1624
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 8990e73ab2aa15d6a0068b860ab54feff25bee36
Link: https://github.com/acpica/acpica/commit/8990e73a
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPICA commit 7926d5ca9452c87f866938dcea8f12e1efb58f89
There is an issue in acpi_install_gpe_handler() and acpi_remove_gpe_handler().
The code to obtain the GPE dispatcher type from the Handler->original_flags
is wrong:
if (((Handler->original_flags & ACPI_GPE_DISPATCH_METHOD) ||
(Handler->original_flags & ACPI_GPE_DISPATCH_NOTIFY)) &&
ACPI_GPE_DISPATCH_NOTIFY is 0x03 and ACPI_GPE_DISPATCH_METHOD is 0x02, thus
this statement is TRUE for the following dispatcher types:
0x01 (ACPI_GPE_DISPATCH_HANDLER): not expected
0x02 (ACPI_GPE_DISPATCH_METHOD): expected
0x03 (ACPI_GPE_DISPATCH_NOTIFY): expected
There is no functional issue due to this because Handler->original_flags is
only set in acpi_install_gpe_handler(), and an earlier checker has excluded
the ACPI_GPE_DISPATCH_HANDLER:
if ((gpe_event_info->Flags & ACPI_GPE_DISPATCH_MASK) ==
ACPI_GPE_DISPATCH_HANDLER)
{
Status = AE_ALREADY_EXISTS;
goto free_and_exit;
}
...
Handler->original_flags = (u8) (gpe_event_info->Flags &
(ACPI_GPE_XRUPT_TYPE_MASK | ACPI_GPE_DISPATCH_MASK));
We need to clean this up before modifying the GPE dispatcher type values.
In order to prevent such issue from happening in the future, this patch
introduces ACPI_GPE_DISPATCH_TYPE() macro to be used to obtain the GPE
dispatcher types. Lv Zheng.
Link: https://github.com/acpica/acpica/commit/7926d5ca
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We need to parse APIC ID for IOAPIC registration for IOAPIC hotplug.
ACPI _MAT method and MADT table are used to figure out IOAPIC ID, just
like parsing CPU APIC ID for CPU hotplug.
[ tglx: Fixed docbook comment ]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/1414387308-27148-8-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Use common resource list management data structure and interfaces
instead of private implementation.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Currently ACPI, PCI and pnp all implement the same resource list
management with different data structure. We need to transfer from
one data structure into another when passing resources from one
subsystem into another subsystem. So move struct resource_list_entry
from ACPI into resource core and rename it as resource_entry,
then it could be reused by different subystems and avoid the data
structure conversion.
Introduce dedicated header file resource_ext.h instead of embedding
it into ioport.h to avoid header file inclusion order issues.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The cevt-r4k driver used to call into the GIC driver to find whether the
timer was pending, but only with External Interrupt Controller (EIC)
mode, where the Cause.IP bits can't be used as they encode the interrupt
priority level (Cause.RIPL) instead.
However commit e9de688dac65 ("irqchip: mips-gic: Support local
interrupts") changed the condition from cpu_has_veic to gic_present.
This fails on cores such as P5600 which have a GIC but the local
interrupts aren't routable by the GIC, causing c0_compare_int_usable()
to consider the interrupt unusable so r4k_clockevent_init() fails.
The previous behaviour, added in commit 98b67c37db33 ("MIPS: Add EIC
support for GIC."), wasn't really correct either as far as I can tell,
since P5600 apparently supports EIC mode too, and in any case the use of
Cause.TI with r2 should have been sufficient anyway since commit
010c108d7af7 ("MIPS: PowerTV: Fix support for timer interrupts with > 64
external IRQs").
Therefore drop the call into the gic driver altogether, and add a
comment in c0_compare_int_pending() to clarify that Cause.TI does get
checked since MIPS r2.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Fixes: e9de688dac65 ("irqchip: mips-gic: Support local interrupts")
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven J. Hill <steven.hill@imgtec.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9077/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Add three methods to allow exporting pnfs block layout volumes:
- get_uuid: get a filesystem unique signature exposed to clients
- map_blocks: map and if nessecary allocate blocks for a layout
- commit_blocks: commit blocks in a layout once the client is done with them
For now we stick the external pnfs block layout interfaces into s_export_op to
avoid mixing them up with the internal interface between the NFS server and
the layout drivers. Once we've fully internalized the latter interface we
can redecide if these methods should stay in s_export_ops.
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
After f78146b0f923, "KVM: Fix page-crossing MMIO", and
87da7e66a405, "KVM: x86: fix vcpu->mmio_fragments overflow",
actually KVM_MMIO_SIZE is gone.
Signed-off-by: Tiejun Chen <tiejun.chen@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
include/net/ipv6.h:713:22: warning: incorrect type in assignment (different base types)
include/net/ipv6.h:713:22: expected restricted __be32 [usertype] hash
include/net/ipv6.h:713:22: got unsigned int
include/net/ipv6.h:719:25: warning: restricted __be32 degrades to integer
include/net/ipv6.h:719:22: warning: invalid assignment: ^=
include/net/ipv6.h:719:22: left side has type restricted __be32
include/net/ipv6.h:719:22: right side has type unsigned int
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
