| Age | Commit message (Collapse) | Author |
|---|
|
relay_open() will close allocated buffers when failed.
but if cpu offlined, some buffer will not be closed.
this patch fixed it.
and did cleanup for relay_reset() too.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
For some unknown reason at Steven Rostedt added in disabling of the SPE
instruction generation for e500 based PPC cores in commit
6ec562328fda585be2d7f472cfac99d3b44d362a.
We are removing it because:
1. It generates e500 kernels that don't work
2. its not the correct set of flags to do this
3. we handle this in the arch/powerpc/Makefile already
4. its unknown in talking to Steven why he did this
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tested-and-Acked-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Bug #11989: Suspend failure on NForce4-based boards due to chanes in
stop_machine
We should not access active.fnret outside the lock; in theory the next
stop_machine could overwrite it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Inotify watch removals suck violently.
To kick the watch out we need (in this order) inode->inotify_mutex and
ih->mutex. That's fine if we have a hold on inode; however, for all
other cases we need to make damn sure we don't race with umount. We can
*NOT* just grab a reference to a watch - inotify_unmount_inodes() will
happily sail past it and we'll end with reference to inode potentially
outliving its superblock.
Ideally we just want to grab an active reference to superblock if we
can; that will make sure we won't go into inotify_umount_inodes() until
we are done. Cleanup is just deactivate_super().
However, that leaves a messy case - what if we *are* racing with
umount() and active references to superblock can't be acquired anymore?
We can bump ->s_count, grab ->s_umount, which will almost certainly wait
until the superblock is shut down and the watch in question is pining
for fjords. That's fine, but there is a problem - we might have hit the
window between ->s_active getting to 0 / ->s_count - below S_BIAS (i.e.
the moment when superblock is past the point of no return and is heading
for shutdown) and the moment when deactivate_super() acquires
->s_umount.
We could just do drop_super() yield() and retry, but that's rather
antisocial and this stuff is luser-triggerable. OTOH, having grabbed
->s_umount and having found that we'd got there first (i.e. that
->s_root is non-NULL) we know that we won't race with
inotify_umount_inodes().
So we could grab a reference to watch and do the rest as above, just
with drop_super() instead of deactivate_super(), right? Wrong. We had
to drop ih->mutex before we could grab ->s_umount. So the watch
could've been gone already.
That still can be dealt with - we need to save watch->wd, do idr_find()
and compare its result with our pointer. If they match, we either have
the damn thing still alive or we'd lost not one but two races at once,
the watch had been killed and a new one got created with the same ->wd
at the same address. That couldn't have happened in inotify_destroy(),
but inotify_rm_wd() could run into that. Still, "new one got created"
is not a problem - we have every right to kill it or leave it alone,
whatever's more convenient.
So we can use idr_find(...) == watch && watch->inode->i_sb == sb as
"grab it and kill it" check. If it's been our original watch, we are
fine, if it's a newcomer - nevermind, just pretend that we'd won the
race and kill the fscker anyway; we are safe since we know that its
superblock won't be going away.
And yes, this is far beyond mere "not very pretty"; so's the entire
concept of inotify to start with.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We don't want to get rid of the futexes just at exit() time, we want to
drop them when doing an execve() too, since that gets rid of the
previous VM image too.
Doing it at mm_release() time means that we automatically always do it
when we disassociate a VM map from the task.
Reported-by: pageexec@freemail.hu
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Alex Efros <powerman@powerman.name>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix init_idle()'s use of sched_clock()
sched: fix stale value in average load per task
|
|
We only need the cacheline padding on SMP kernels. Saves 6k:
text data bss dec hex filename
5713 388 8840 14941 3a5d kernel/kprobes.o
5713 388 2632 8733 221d kernel/kprobes.o
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
__register_kprobe() can be preempted after checking probing address but
before module_text_address() or try_module_get(), and in this interval
the module can be unloaded. In that case, try_module_get(probed_mod)
will access to invalid address, or kprobe will probe invalid address.
This patch uses preempt_disable() to protect it and uses
__module_text_address() and __kernel_text_address().
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With this change, control file 'freezer.state' doesn't exist in root
cgroup, making root cgroup unfreezable.
I think it's reasonable to disallow freeze tasks in the root cgroup. And
then we can avoid fork overhead when freezer subsystem is compiled but not
used.
Also make writing invalid value to freezer.state returns EINVAL rather
than EIO. This is more consistent with other cgroup subsystem.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: Paul Menage <menage@google.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In theory the task can be moved to another cgroup and the freezer will be
freed right after task_lock is dropped, so the lock results in zero
protection.
But in the case of freezer_fork() no lock is needed, since the task is not
in tasklist yet so it won't be moved to another cgroup, so task->cgroups
won't be changed or invalidated.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Maciej Rutecki reported:
> I have this bug during suspend to disk:
>
> [ 188.592151] Enabling non-boot CPUs ...
> [ 188.592151] SMP alternatives: switching to SMP code
> [ 188.666058] BUG: using smp_processor_id() in preemptible
> [00000000]
> code: suspend_to_disk/2934
> [ 188.666064] caller is native_sched_clock+0x2b/0x80
Which, as noted by Linus, was caused by me, via:
7cbaef9c "sched: optimize sched_clock() a bit"
Move the rq locking a bit earlier in the initialization sequence,
that will make the sched_clock() call in init_idle() non-preemptible.
Reported-by: Maciej Rutecki <maciej.rutecki@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix load balancer load average calculation accuracy
cpu_avg_load_per_task() returns a stale value when nr_running is 0.
It returns an older stale (caculated when nr_running was non zero) value.
This patch returns and sets rq->avg_load_per_task to zero when nr_running
is 0.
Compile and boot tested on a x86_64 box.
Signed-off-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: cleanup
git grep HRTIMER_CB_IRQSAFE revealed half the callback modes are actually
unused.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: handle HRTIMER_CB_IRQSAFE_UNLOCKED correctly from softirq context
nohz: disable tick_nohz_kick_tick() for now
irq: call __irq_enter() before calling the tick_idle_check
x86: HPET: enter hpet_interrupt_handler with interrupts disabled
x86: HPET: read from HPET_Tn_CMP() not HPET_T0_CMP
x86: HPET: convert WARN_ON to WARN_ON_ONCE
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: release buddies on yield
fix for account_group_exec_runtime(), make sure ->signal can't be freed under rq->lock
sched: clean up debug info
|
|
Clear buddies on yield, so that the buddy rules don't schedule them
despite them being placed right-most.
This fixed a performance regression with yield-happy binary JVMs.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Lin Ming <ming.m.lin@intel.com>
|
|
Impact: fix incorrect locking triggered during hotplug-intense stress-tests
While migrating the the CB_IRQSAFE_UNLOCKED timers during a cpu-offline,
we queue them on the cb_pending list, so that they won't go
stale.
Thus, when the callbacks of the timers run from the softirq context,
they could run into potential deadlocks, since these callbacks
assume that they're running with irq's disabled, thereby annoying
lockdep!
Fix this by emulating hardirq context while running these callbacks from
the hrtimer softirq.
=================================
[ INFO: inconsistent lock state ]
2.6.27 #2
--------------------------------
inconsistent {in-hardirq-W} -> {hardirq-on-W} usage.
ksoftirqd/0/4 [HC0[0]:SC1[1]:HE1:SE0] takes:
(&rq->lock){++..}, at: [<c011db84>] sched_rt_period_timer+0x9e/0x1fc
{in-hardirq-W} state was registered at:
[<c014103c>] __lock_acquire+0x549/0x121e
[<c0107890>] native_sched_clock+0x88/0x99
[<c013aa12>] clocksource_get_next+0x39/0x3f
[<c0139abc>] update_wall_time+0x616/0x7df
[<c0141d6b>] lock_acquire+0x5a/0x74
[<c0121724>] scheduler_tick+0x3a/0x18d
[<c047ed45>] _spin_lock+0x1c/0x45
[<c0121724>] scheduler_tick+0x3a/0x18d
[<c0121724>] scheduler_tick+0x3a/0x18d
[<c012c436>] update_process_times+0x3a/0x44
[<c013c044>] tick_periodic+0x63/0x6d
[<c013c062>] tick_handle_periodic+0x14/0x5e
[<c010568c>] timer_interrupt+0x44/0x4a
[<c0150c9f>] handle_IRQ_event+0x13/0x3d
[<c0151c14>] handle_level_irq+0x79/0xbd
[<c0105634>] do_IRQ+0x69/0x7d
[<c01041e4>] common_interrupt+0x28/0x30
[<c047007b>] aac_probe_one+0x1a3/0x3f3
[<c047ec2d>] _spin_unlock_irqrestore+0x36/0x39
[<c01512b4>] setup_irq+0x1be/0x1f9
[<c065d70b>] start_kernel+0x259/0x2c5
[<ffffffff>] 0xffffffff
irq event stamp: 50102
hardirqs last enabled at (50102): [<c047ebf4>] _spin_unlock_irq+0x20/0x23
hardirqs last disabled at (50101): [<c047edc2>] _spin_lock_irq+0xa/0x4b
softirqs last enabled at (50088): [<c0128ba6>] do_softirq+0x37/0x4d
softirqs last disabled at (50099): [<c0128ba6>] do_softirq+0x37/0x4d
other info that might help us debug this:
no locks held by ksoftirqd/0/4.
stack backtrace:
Pid: 4, comm: ksoftirqd/0 Not tainted 2.6.27 #2
[<c013f6cb>] print_usage_bug+0x13e/0x147
[<c013fef5>] mark_lock+0x493/0x797
[<c01410b1>] __lock_acquire+0x5be/0x121e
[<c0141d6b>] lock_acquire+0x5a/0x74
[<c011db84>] sched_rt_period_timer+0x9e/0x1fc
[<c047ed45>] _spin_lock+0x1c/0x45
[<c011db84>] sched_rt_period_timer+0x9e/0x1fc
[<c011db84>] sched_rt_period_timer+0x9e/0x1fc
[<c01210fd>] finish_task_switch+0x41/0xbd
[<c0107890>] native_sched_clock+0x88/0x99
[<c011dae6>] sched_rt_period_timer+0x0/0x1fc
[<c0136dda>] run_hrtimer_pending+0x54/0xe5
[<c011dae6>] sched_rt_period_timer+0x0/0x1fc
[<c0128afb>] __do_softirq+0x7b/0xef
[<c0128ba6>] do_softirq+0x37/0x4d
[<c0128c12>] ksoftirqd+0x56/0xc5
[<c0128bbc>] ksoftirqd+0x0/0xc5
[<c0134649>] kthread+0x38/0x5d
[<c0134611>] kthread+0x0/0x5d
[<c0104477>] kernel_thread_helper+0x7/0x10
=======================
Signed-off-by: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-trace into tracing/urgent
|
|
under rq->lock
Impact: fix hang/crash on ia64 under high load
This is ugly, but the simplest patch by far.
Unlike other similar routines, account_group_exec_runtime() could be
called "implicitly" from within scheduler after exit_notify(). This
means we can race with the parent doing release_task(), we can't just
check ->signal != NULL.
Change __exit_signal() to do spin_unlock_wait(&task_rq(tsk)->lock)
before __cleanup_signal() to make sure ->signal can't be freed under
task_rq(tsk)->lock. Note that task_rq_unlock_wait() doesn't care
about the case when tsk changes cpu/rq under us, this should be OK.
Thanks to Ingo who nacked my previous buggy patch.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reported-by: Doug Chapman <doug.chapman@hp.com>
|
|
Impact: removal of unnecessary looping
The lockless part of the ring buffer allows for reentry into the code
from interrupts. A timestamp is taken, a test is preformed and if it
detects that an interrupt occurred that did tracing, it tries again.
The problem arises if the timestamp code itself causes a trace.
The detection will detect this and loop again. The difference between
this and an interrupt doing tracing, is that this will fail every time,
and cause an infinite loop.
Currently, we test if the loop happens 1000 times, and if so, it will
produce a warning and disable the ring buffer.
The problem with this approach is that it makes it difficult to perform
some types of tracing (tracing the timestamp code itself).
Each trace entry has a delta timestamp from the previous entry.
If a trace entry is reserved but and interrupt occurs and traces before
the previous entry is commited, the delta timestamp for that entry will
be zero. This actually makes sense in terms of tracing, because the
interrupt entry happened before the preempted entry was commited, so
one may consider the two happening at the same time. The order is
still preserved in the buffer.
With this idea, instead of trying to get a new timestamp if an interrupt
made it in between the timestamp and the test, the entry could simply
make the delta zero and continue. This will prevent interrupts or
tracers in the timer code from causing the above loop.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
|
|
Impact: fix for bug on resize
This patch addresses the bug found here:
http://bugzilla.kernel.org/show_bug.cgi?id=11996
When ftrace converted to the new unified trace buffer, the resizing of
the buffer was not protected as much as it was originally. If tracing
is performed while the resize occurs, then the buffer can be corrupted.
This patch disables all ftrace buffer modifications before a resize
takes place.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
|
|
Impact: nohz powersavings and wakeup regression
commit fb02fbc14d17837b4b7b02dbb36142c16a7bf208 (NOHZ: restart tick
device from irq_enter()) causes a serious wakeup regression.
While the patch is correct it does not take into account that spurious
wakeups happen on x86. A fix for this issue is available, but we just
revert to the .27 behaviour and let long running softirqs screw
themself.
Disable it for now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Impact: avoid spurious ksoftirqd wakeups
The tick idle check which is called from irq_enter() was run before
the call to __irq_enter() which did not set the in_interrupt() bits in
preempt_count. That way the raise of a softirq woke up softirqd for
nothing as the softirq was handled on return from interrupt.
Call __irq_enter() before calling into the tick idle check code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: clean up and fix debug info printout
While looking over the sched_debug code I noticed that we printed the rq
schedstats for every cfs_rq, ammend this.
Also change nr_spead_over into an int, and fix a little buglet in
min_vruntime printing.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'cpus4096' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
cpumask: introduce new API, without changing anything, v3
cpumask: new API, v2
cpumask: introduce new API, without changing anything
|
|
Impact: fix rare memory leak in the sched-domains manual reconfiguration code
In the failure path, rd is not attached to a sched domain,
so it causes a leak.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: re-add incorrectly eliminated sched domain layers
(1) on i386 with SCHED_SMT and SCHED_MC enabled
# mount -t cgroup -o cpuset xxx /mnt
# echo 0 > /mnt/cpuset.sched_load_balance
# mkdir /mnt/0
# echo 0 > /mnt/0/cpuset.cpus
# dmesg
CPU0 attaching sched-domain:
domain 0: span 0 level CPU
groups: 0
(2) on i386 with SCHED_MC enabled but SCHED_SMT disabled
# same with (1)
# dmesg
CPU0 attaching NULL sched-domain.
The bug is that some sched domains may be skipped unintentionally when
degenerating (optimizing) sched domains.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Block: use round_jiffies_up()
Add round_jiffies_up and related routines
block: fix __blkdev_get() for removable devices
generic-ipi: fix the smp_mb() placement
blk: move blk_delete_timer call in end_that_request_last
block: add timer on blkdev_dequeue_request() not elv_next_request()
bio: define __BIOVEC_PHYS_MERGEABLE
block: remove unused ll_new_mergeable()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: re-tune balancing
sched: fix buddies for group scheduling
sched: backward looking buddy
sched: fix fair preempt check
sched: cleanup fair task selection
|
|
This fixes an oops when reading /proc/sched_debug.
A cgroup won't be removed completely until finishing cgroup_diput(), so we
shouldn't invalidate cgrp->dentry in cgroup_rmdir(). Otherwise, when a
group is being removed while cgroup_path() gets called, we may trigger
NULL dereference BUG.
The bug can be reproduced:
# cat test.sh
#!/bin/sh
mount -t cgroup -o cpu xxx /mnt
for (( ; ; ))
{
mkdir /mnt/sub
rmdir /mnt/sub
}
# ./test.sh &
# cat /proc/sched_debug
BUG: unable to handle kernel NULL pointer dereference at 00000038
IP: [<c045a47f>] cgroup_path+0x39/0x90
...
Call Trace:
[<c0420344>] ? print_cfs_rq+0x6e/0x75d
[<c0421160>] ? sched_debug_show+0x72d/0xc1e
...
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Paul Menage <menage@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org> [2.6.26.x, 2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Impact: introduce new APIs
We want to deprecate cpumasks on the stack, as we are headed for
gynormous numbers of CPUs. Eventually, we want to head towards an
undefined 'struct cpumask' so they can never be declared on stack.
1) New cpumask functions which take pointers instead of copies.
(cpus_* -> cpumask_*)
2) Several new helpers to reduce requirements for temporary cpumasks
(cpumask_first_and, cpumask_next_and, cpumask_any_and)
3) Helpers for declaring cpumasks on or offstack for large NR_CPUS
(cpumask_var_t, alloc_cpumask_var and free_cpumask_var)
4) 'struct cpumask' for explicitness and to mark new-style code.
5) Make iterator functions stop at nr_cpu_ids (a runtime constant),
not NR_CPUS for time efficiency and for smaller dynamic allocations
in future.
6) cpumask_copy() so we can allocate less than a full cpumask eventually
(for alloc_cpumask_var), and so we can eliminate the 'struct cpumask'
definition eventually.
7) work_on_cpu() helper for doing task on a CPU, rather than saving old
cpumask for current thread and manipulating it.
8) smp_call_function_many() which is smp_call_function_mask() except
taking a cpumask pointer.
Note that this patch simply introduces the new functions and leaves
the obsolescent ones in place. This is to simplify the transition
patches.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
This patch (as1158b) adds round_jiffies_up() and friends. These
routines work like the analogous round_jiffies() functions, except
that they will never round down.
The new routines will be useful for timeouts where we don't care
exactly when the timer expires, provided it doesn't expire too soon.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
smp_mb() is needed (to make the memory operations visible globally) before
sending the ipi on the sender and the receiver (on Alpha atleast) needs
smp_read_barrier_depends() in the handler before reading the call_single_queue
list in a lock-free fashion.
On x86, x2apic mode register accesses for sending IPI's don't have serializing
semantics. So the need for smp_mb() before sending the IPI becomes more
critical in x2apic mode.
Remove the unnecessary smp_mb() in csd_flag_wait(), as the presence of that
smp_mb() doesn't mean anything on the sender, when the ipi receiver is not
doing any thing special (like memory fence) after clearing the CSD_FLAG_WAIT.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Impact: scheduling order fix for group scheduling
For each level in the hierarchy, set the buddy to point to the right entity.
Therefore, when we do the hierarchical schedule, we have a fair chance of
ending up where we meant to.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: improve/change/fix wakeup-buddy scheduling
Currently we only have a forward looking buddy, that is, we prefer to
schedule to the task we last woke up, under the presumption that its
going to consume the data we just produced, and therefore will have
cache hot benefits.
This allows co-waking producer/consumer task pairs to run ahead of the
pack for a little while, keeping their cache warm. Without this, we
would interleave all pairs, utterly trashing the cache.
This patch introduces a backward looking buddy, that is, suppose that
in the above scenario, the consumer preempts the producer before it
can go to sleep, we will therefore miss the wakeup from consumer to
producer (its already running, after all), breaking the cycle and
reverting to the cache-trashing interleaved schedule pattern.
The backward buddy will try to schedule back to the task that woke us
up in case the forward buddy is not available, under the assumption
that the last task will be the one with the most cache hot task around
barring current.
This will basically allow a task to continue after it got preempted.
In order to avoid starvation, we allow either buddy to get wakeup_gran
ahead of the pack.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: fix cross-class preemption
Inter-class wakeup preemptions should go on class order.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: cleanup
Clean up task selection
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
In 777e208d40d0953efc6fb4ab58590da3f7d8f02d we changed from outputting
field->cpu (a char) to iter->cpu (unsigned int), increasing the resulting
structure size by 3 bytes.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
While writing a new tracer, I had a bug where I caused the ring-buffer
to recurse in a bad way. The bug was with the tracer I was writing
and not the ring-buffer itself. But it took a long time to find the
problem.
This patch adds paranoid checks into the ring-buffer infrastructure
that will catch bugs of this nature.
Note: I put the bug back in the tracer and this patch showed the error
nicely and prevented the lockup.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Impact: ia64+tracing build fix
When a function is kprobed, the return address is set to the
kprobe_trampoline, or something similar. This caused the output
of the trace to look confusing when the parent seemed to be this
"kprobe_trampoline" function.
To fix this, Abhishek Sagar added a test of the instruction pointer
of the parent to see if it matched the kprobe_trampoline. If it
did, the output would print a "[unknown/kretprobe'd]" instead.
Unfortunately, not all archs do this the same way, and the trampoline
function may not be exported, which causes failures in builds.
This patch will compare the name instead of the pointer to see
if it matches. This prevents us from depending on a function from
being exported, and should work on all archs. The worst that can
happen is that an arch might use a different name and then we
go back to the confusing output. At least the arch will still build.
Reported-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Abhishek Sagar <sagar.abhishek@gmail.com>
Acked-by: Abhishek Sagar <sagar.abhishek@gmail.com>
|
|
Impact: build fix on !stacktrace architectures
only select STACKTRACE on architectures that have STACKTRACE_SUPPORT
... since we also need to ifdef out the guts of ftrace_trace_stack().
We also want to disallow setting TRACE_ITER_STACKTRACE in trace_flags
on such configs, but that can wait.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Insufficient dependency - we really want CONFIG_RTC_CLASS=y there.
That will give us CONFIG_RTC_LIB=y, so the old dependency can be
simply replaced.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This one apparently doesn't generate any warnings, because the function
is only used during system bootup, when the warnings are disabled. But
it's still very wrong.
The __reserve_region_with_split() function is called with the
resource_lock held for writing, so it must only ever do GFP_ATOMIC
allocations.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: remove sched-design.txt from 00-INDEX
sched: change sched_debug's mode to 0444
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ftrace: handle archs that do not support irqs_disabled_flags
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
resources: fix x86info results ioremap.c:226 __ioremap_caller+0xf2/0x2d6() WARNINGs
|
|
Impact: build fix on non-lockdep architectures
Some architectures do not support a way to read the irq flags that
is set from "local_irq_save(flags)" to determine if interrupts were
disabled or enabled. Ftrace uses this information to display to the user
if the trace occurred with interrupts enabled or disabled.
Besides the fact that those archs that do not support this will fail to
compile, unless they fix it, we do not want to have the trace simply
say interrupts were not disabled or they were enabled, without knowing
the real answer.
This patch adds a 'X' in the output to let the user know that the
architecture they are running on does not support a way for the tracer
to determine if interrupts were enabled or disabled. It also lets those
same archs compile with tracing enabled.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
ftrace: fix trace_nop config select
ftrace: perform an initialization for ftrace to enable it
|
|
Currently "kill <sig> -1" kills processes in all namespaces and breaks the
isolation of namespaces. Earlier attempt to fix this was discussed at:
http://lkml.org/lkml/2008/7/23/148
As suggested by Oleg Nesterov in that thread, use "task_pid_vnr() > 1"
check since task_pid_vnr() returns 0 if process is outside the caller's
namespace.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Tested-by: Daniel Hokka Zakrisson <daniel@hozac.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
profile_init() calls in to alloc_bootmem() on early initialization. While
alloc_bootmem() is __init, the reference itself is safe in that it is
tucked below a !slab_is_available() check. So, flag profile_init() as
__ref.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Dave Hansen <dave@linux.vnet.ibm.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
