| Age | Commit message (Collapse) | Author |
|---|
|
Parsing of new mode flags in the tmpfs mpol mount option is slightly broken:
Setting a valid flag works OK:
#mount -o remount,mpol=bind=static:1-2 /dev/shm
#mount
...
tmpfs on /dev/shm type tmpfs (rw,mpol=bind=static:1-2)
...
However, we can't remove them or change them, once we've
set a valid flag:
#mount -o remount,mpol=bind:1-2 /dev/shm
#mount
...
tmpfs on /dev/shm type tmpfs (rw,mpol=bind:1-2)
...
It SAYS it removed it, but that's just a copy of the input
string. If we now try to set it to a different flag, we
get:
#mount -o remount,mpol=bind=relative:1-2 /dev/shm
mount: /dev/shm not mounted already, or bad option
And on the console, we see:
tmpfs: Bad value 'bind' for mount option 'mpol'
^ lost remainder of string
Furthermore, bogus flags are accepted with out error.
Granted, they are a no-op:
#mount -o remount,mpol=interleave=foo:0-3 /dev/shm
#mount
...
tmpfs on /dev/shm type tmpfs (rw,mpol=interleave=foo:0-3)
Again, that's just a copy of the input string shown by the mount command.
This patch fixes the behavior by pre-zeroing the flags so that only one of the
mutually exclusive flags can be set at one time. It also reports an error
when an unrecognized flag is specified.
The check for both flags being set is removed because it can't happen with
this implementation. If we ever want to support multiple non-exclusive flags,
this area will need rework and we will need to check that any mutually
exclusive flags aren't specified.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Paul Jackson <pj@sgi.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Eric Whitney <eric.whitney@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Adds another optional mode flag, MPOL_F_RELATIVE_NODES, that specifies
nodemasks passed via set_mempolicy() or mbind() should be considered relative
to the current task's mems_allowed.
When the mempolicy is created, the passed nodemask is folded and mapped onto
the current task's mems_allowed. For example, consider a task using
set_mempolicy() to pass MPOL_INTERLEAVE | MPOL_F_RELATIVE_NODES with a
nodemask of 1-3. If current's mems_allowed is 4-7, the effected nodemask is
5-7 (the second, third, and fourth node of mems_allowed).
If the same task is attached to a cpuset, the mempolicy nodemask is rebound
each time the mems are changed. Some possible rebinds and results are:
mems result
1-3 1-3
1-7 2-4
1,5-6 1,5-6
1,5-7 5-7
Likewise, the zonelist built for MPOL_BIND acts on the set of zones assigned
to the resultant nodemask from the relative remap.
In the MPOL_PREFERRED case, the preferred node is remapped from the currently
effected nodemask to the relative nodemask.
This mempolicy mode flag was conceived of by Paul Jackson <pj@sgi.com>.
Cc: Paul Jackson <pj@sgi.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add an optional mempolicy mode flag, MPOL_F_STATIC_NODES, that suppresses the
node remap when the policy is rebound.
Adds another member to struct mempolicy, nodemask_t user_nodemask, as part of
a union with cpuset_mems_allowed:
struct mempolicy {
...
union {
nodemask_t cpuset_mems_allowed;
nodemask_t user_nodemask;
} w;
}
that stores the the nodemask that the user passed when he or she created the
mempolicy via set_mempolicy() or mbind(). When using MPOL_F_STATIC_NODES,
which is passed with any mempolicy mode, the user's passed nodemask
intersected with the VMA or task's allowed nodes is always used when
determining the preferred node, setting the MPOL_BIND zonelist, or creating
the interleave nodemask. This happens whenever the policy is rebound,
including when a task's cpuset assignment changes or the cpuset's mems are
changed.
This creates an interesting side-effect in that it allows the mempolicy
"intent" to lie dormant and uneffected until it has access to the node(s) that
it desires. For example, if you currently ask for an interleaved policy over
a set of nodes that you do not have access to, the mempolicy is not created
and the task continues to use the previous policy. With this change, however,
it is possible to create the same mempolicy; it is only effected when access
to nodes in the nodemask is acquired.
It is also possible to mount tmpfs with the static nodemask behavior when
specifying a node or nodemask. To do this, simply add "=static" immediately
following the mempolicy mode at mount time:
mount -o remount mpol=interleave=static:1-3
Also removes mpol_check_policy() and folds its logic into mpol_new() since it
is now obsoleted. The unused vma_mpol_equal() is also removed.
Cc: Paul Jackson <pj@sgi.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With the evolution of mempolicies, it is necessary to support mempolicy mode
flags that specify how the policy shall behave in certain circumstances. The
most immediate need for mode flag support is to suppress remapping the
nodemask of a policy at the time of rebind.
Both the mempolicy mode and flags are passed by the user in the 'int policy'
formal of either the set_mempolicy() or mbind() syscall. A new constant,
MPOL_MODE_FLAGS, represents the union of legal optional flags that may be
passed as part of this int. Mempolicies that include illegal flags as part of
their policy are rejected as invalid.
An additional member to struct mempolicy is added to support the mode flags:
struct mempolicy {
...
unsigned short policy;
unsigned short flags;
}
The splitting of the 'int' actual passed by the user is done in
sys_set_mempolicy() and sys_mbind() for their respective syscalls. This is
done by intersecting the actual with MPOL_MODE_FLAGS, rejecting the syscall of
there are additional flags, and storing it in the new 'flags' member of struct
mempolicy. The intersection of the actual with ~MPOL_MODE_FLAGS is stored in
the 'policy' member of the struct and all current users of pol->policy remain
unchanged.
The union of the policy mode and optional mode flags is passed back to the
user in get_mempolicy().
This combination of mode and flags within the same actual does not break
userspace code that relies on get_mempolicy(&policy, ...) and either
switch (policy) {
case MPOL_BIND:
...
case MPOL_INTERLEAVE:
...
};
statements or
if (policy == MPOL_INTERLEAVE) {
...
}
statements. Such applications would need to use optional mode flags when
calling set_mempolicy() or mbind() for these previously implemented statements
to stop working. If an application does start using optional mode flags, it
will need to mask the optional flags off the policy in switch and conditional
statements that only test mode.
An additional member is also added to struct shmem_sb_info to store the
optional mode flags.
[hugh@veritas.com: shmem mpol: fix build warning]
Cc: Paul Jackson <pj@sgi.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The mempolicy mode constants, MPOL_DEFAULT, MPOL_PREFERRED, MPOL_BIND, and
MPOL_INTERLEAVE, are better declared as part of an enum since they are
sequentially numbered and cannot be combined.
The policy member of struct mempolicy is also converted from type short to
type unsigned short. A negative policy does not have any legitimate meaning,
so it is possible to change its type in preparation for adding optional mode
flags later.
The equivalent member of struct shmem_sb_info is also changed from int to
unsigned short.
For compatibility, the policy formal to get_mempolicy() remains as a pointer
to an int:
int get_mempolicy(int *policy, unsigned long *nmask,
unsigned long maxnode, unsigned long addr,
unsigned long flags);
although the only possible values is the range of type unsigned short.
Cc: Paul Jackson <pj@sgi.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert tiny-shmem.c function comments to kernel-doc. Add parameters and
convert/fix other kernel-doc in shmem.c.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
My memcgroup patch to fix hang with shmem/tmpfs added NULL page handling to
mem_cgroup_charge_common. It seemed convenient at the time, but hard to
justify now: there's a perfectly appropriate swappage to charge and uncharge
instead, this is not on any hot path through shmem_getpage, and no performance
hit was observed from the slight extra overhead.
So revert that NULL page handling from mem_cgroup_charge_common; and make it
clearer by bringing page_cgroup_assign_new_page_cgroup into its body - that
was a helper I found more of a hindrance to understanding.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: David Rientjes <rientjes@google.com>
Acked-by: Balbir Singh <balbir@linux.vnet.ibm.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Hirokazu Takahashi <taka@valinux.co.jp>
Cc: YAMAMOTO Takashi <yamamoto@valinux.co.jp>
Cc: Paul Menage <menage@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Documentation/SubmitCheckist, please.
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add .show_options super operation to tmpfs.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The memcgroup regime relies upon a cgroup reclaiming pages from itself within
add_to_page_cache: which may involve some waiting. Whereas shmem and tmpfs
rely upon using add_to_page_cache while holding a spinlock: when it cannot
wait. The consequence is that when a cgroup reaches its limit, shmem_getpage
just hangs - unless there is outside memory pressure too, neither kswapd nor
radix_tree_preload get it out of the retry loop.
In most cases we can mem_cgroup_cache_charge the page waitably first, to
attach the page_cgroup in advance, so add_to_page_cache will do no more than
increment a count; then mem_cgroup_uncharge_page after (in both success and
failure cases) to balance the books again.
And where there used to be a congestion_wait for kswapd (recently made
redundant by radix_tree_preload), use mem_cgroup_cache_charge with NULL page
to go through a cycle of allocation and freeing, without accounting to any
particular page, and without updating the statistics vector. This brings the
cgroup below its limit so the next try usually succeeds.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Balbir Singh <balbir@linux.vnet.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch modifies the interface to inode_getsecurity to have the function
return a buffer containing the security blob and its length via parameters
instead of relying on the calling function to give it an appropriately sized
buffer.
Security blobs obtained with this function should be freed using the
release_secctx LSM hook. This alleviates the problem of the caller having to
guess a length and preallocate a buffer for this function allowing it to be
used elsewhere for Labeled NFS.
The patch also removed the unused err parameter. The conversion is similar to
the one performed by Al Viro for the security_getprocattr hook.
Signed-off-by: David P. Quigley <dpquigl@tycho.nsa.gov>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Chris Wright <chrisw@sous-sol.org>
Acked-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Casey Schaufler <casey@schaufler-ca.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Intensive swapoff testing shows shmem_unuse spinning on an entry in
shmem_swaplist pointing to itself: how does that come about? Days pass...
First guess is this: shmem_delete_inode tests list_empty without taking the
global mutex (so the swapping case doesn't slow down the common case); but
there's an instant in shmem_unuse_inode's list_move_tail when the list entry
may appear empty (a rare case, because it's actually moving the head not the
the list member). So there's a danger of leaving the inode on the swaplist
when it's freed, then reinitialized to point to itself when reused. Fix that
by skipping the list_move_tail when it's a no-op, which happens to plug this.
But this same spinning then surfaces on another machine. Ah, I'd never
suspected it, but shmem_writepage's swaplist manipulation is unsafe: though we
still hold page lock, which would hold off inode deletion if the page were in
pagecache, it doesn't hold off once it's in swapcache (free_swap_and_cache
doesn't wait on locked pages). Hmm: we could put the the inode on swaplist
earlier, but then shmem_unuse_inode could never prune unswapped inodes.
Fix this with an igrab before dropping info->lock, as in shmem_unuse_inode;
though I am a little uneasy about the iput which has to follow - it works, and
I see nothing wrong with it, but it is surprising that shmem inode deletion
may now occur below shmem_writepage. Revisit this fix later?
And while we're looking at these races: the way shmem_unuse tests swapped
without holding info->lock looks unsafe, if we've more than one swap area: a
racing shmem_writepage on another page of the same inode could be putting it
in swapcache, just as we're deciding to remove the inode from swaplist -
there's a danger of going on swap without being listed, so a later swapoff
would hang, being unable to locate the entry. Move that test and removal down
into shmem_unuse_inode, once info->lock is held.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Nick has observed that shmem.c still uses GFP_ATOMIC when adding to page cache
or swap cache, without any radix tree preload: so tending to deplete emergency
reserves of memory.
GFP_ATOMIC remains appropriate in shmem_writepage's add_to_swap_cache: it's
being called under memory pressure, so must not wait for more memory to become
available. But shmem_unuse_inode now has a window in which it can and should
preload with GFP_KERNEL, and say GFP_NOWAIT instead of GFP_ATOMIC in its
add_to_page_cache.
shmem_getpage is not so straightforward: its filepage/swappage integrity
relies upon exchanging between caches under spinlock, and it would need a lot
of restructuring to place the preloads correctly. Instead, follow its pattern
of retrying on races: use GFP_NOWAIT instead of GFP_ATOMIC in
add_to_page_cache, and begin each circuit of the repeat loop with a sleeping
radix_tree_preload, followed immediately by radix_tree_preload_end - that
won't guarantee success in the next add_to_page_cache, but doesn't need to.
And we can then remove that bothersome congestion_wait: when needed, it'll
automatically get done in the course of the radix_tree_preload.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Looks-good-to: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are a couple of reasons (patches follow) why it would be good to open a
window for sleep in shmem_unuse_inode, between its search for a matching swap
entry, and its handling of the entry found.
shmem_unuse_inode must then use igrab to hold the inode against deletion in
that window, and its corresponding iput might result in deletion: so it had
better unlock_page before the iput, and might as well release the page too.
Nor is there any need to hold on to shmem_swaplist_mutex once we know we'll
leave the loop. So this unwinding moves from try_to_unuse and shmem_unuse
into shmem_unuse_inode, in the case when it finds a match.
Let try_to_unuse break on error in the shmem_unuse case, as it does in the
unuse_mm case: though at this point in the series, no error to break on.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
shmem_unuse is at present an unbroken search through every swap vector page of
every tmpfs file which might be swapped, all under shmem_swaplist_lock. This
dates from long ago, when the caller held mmlist_lock over it all too: long
gone, but there's never been much pressure for preemptible swapoff.
Make it a little more preemptible, replacing shmem_swaplist_lock by
shmem_swaplist_mutex, inserting a cond_resched in the main loop, and a
cond_resched_lock (on info->lock) at one convenient point in the
shmem_unuse_inode loop, where it has no outstanding kmap_atomic.
If we're serious about preemptible swapoff, there's much further to go e.g.
I'm stupid to let the kmap_atomics of the decreasingly significant HIGHMEM
case dictate preemptiblility for other configs. But as in the earlier patch
to make swapoff scan ptes preemptibly, my hidden agenda is really towards
making memcgroups work, hardly about preemptibility at all.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
tmpfs is expected to limit the memory used (unless mounted with nr_blocks=0 or
size=0). But if a stacked filesystem such as unionfs gets pages from a sparse
tmpfs file by reading holes, and then writes to them, it can easily exceed any
such limit at present.
So suppress the SGP_READ "don't allocate page" ZERO_PAGE optimization when
reading for the kernel (a KERNEL_DS check, ugh, sorry about that). Indeed,
pessimistically mark such pages as dirty, so they cannot get reclaimed and
unaccounted by mistake. The venerable shmem_recalc_inode code (originally to
account for the reclaim of clean pages) suffices to get the accounting right
when swappages are dropped in favour of more uptodate filepages.
This also fixes the NULL shmem_swp_entry BUG or oops in shmem_writepage,
caused by unionfs writing to a very sparse tmpfs file: to minimize memory
allocation in swapout, tmpfs requires the swap vector be allocated upfront,
which wasn't always happening in this stacked case.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
tmpfs has long allowed for a fresh filepage to be created in pagecache, just
before shmem_getpage gets the chance to match it up with the swappage which
already belongs to that offset. But unionfs_writepage now does a
find_or_create_page, divorced from shmem_getpage, which leaves conflicting
filepage and swappage outstanding indefinitely, when unionfs is over tmpfs.
Therefore shmem_writepage (where a page is swizzled from file to swap) must
now be on the lookout for existing swap, ready to free it in favour of the
more uptodate filepage, instead of BUGging on that clash. And when the
add_to_page_cache fails in shmem_unuse_inode, it must defer to an uptodate
filepage, otherwise swapoff would hang. Whereas when add_to_page_cache fails
in shmem_getpage, it should retry in the same way it already does.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
move_to_swap_cache and move_from_swap_cache functions (which swizzle a page
between tmpfs page cache and swap cache, to avoid page copying) are only used
by shmem.c; and our subsequent fix for unionfs needs different treatments in
the two instances of move_from_swap_cache. Move them from swap_state.c into
their callsites shmem_writepage, shmem_unuse_inode and shmem_getpage, making
add_to_swap_cache externally visible.
shmem.c likes to say set_page_dirty where swap_state.c liked to say
SetPageDirty: respect that diversity, which __set_page_dirty_no_writeback
makes moot (and implies we should lose that "shift page from clean_pages to
dirty_pages list" comment: it's on neither).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When tmpfs is mounted with a size less than one page, the number of blocks
is set to 0 which makes the tmpfs mount unlimited. This can lead to a
quick and surprising death if someone typos a tmpfs mount command and
writes too much.
tmpfs can still be mounted as unlimited if size or nr_blocks is exactly 0,
as Documentation/filesystems/tmpfs.txt says.
Hugh: do this by rounding size up instead of down in all cases: which
slightly expands other odd-sized tmpfs mounts, but in a consistent way.
Signed-off-by: Michael Marineau <mike@marineau.org>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The shmem_sb_info structure has a number of free_inodes. This
value is altered in appropriate places under spinlock and with
the sbi->max_inodes != 0 check.
Consolidate these manipulations into two helpers.
This is minus 42 bytes of shmem.o and minus 4 :) lines of code.
[akpm@linux-foundation.org: fix error return values]
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
With the old aops, writing to a tmpfs file had to use its own special method:
the generic method would pass in a fresh page to prepare_write when the right
page was there in swapcache - which was inefficient to handle, even once we'd
concocted the code to handle it.
With the new aops, the generic method uses shmem_write_end, which lets
shmem_getpage find the right page: so now abandon shmem_file_write in favour
of the generic method. Yes, that does do several things that tmpfs hasn't
really needed (notably balance_dirty_pages_ratelimited, which ramfs also
calls); but more use of common code is preferable.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In the new aops, write_begin is supposed to return the page locked: though
I've seen no ill effects, that's been overlooked in the case of
shmem_write_begin, and should be fixed. Then shmem_write_end must unlock the
page: do so _after_ updating i_size, as we found to be important in other
filesystems (though since shmem pages don't go the usual writeback route, they
never suffered from that corruption).
For shmem_write_begin to return the page locked, we need shmem_getpage to
return the page locked in SGP_WRITE case as well as SGP_CACHE case: let's
simplify the interface and return it locked even when SGP_READ.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove SGP_QUICK from the sgp_type enum: it was for shmem_populate and has no
users now. Remove SGP_FAULT from the enum: SGP_CACHE does just as well (and
shmem_getpage is about to return with page always locked).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Building in a filesystem on a loop device on a tmpfs file can hang when
swapping, the loop thread caught in that infamous throttle_vm_writeout.
In theory this is a long standing problem, which I've either never seen in
practice, or long ago suppressed the recollection, after discounting my load
and my tmpfs size as unrealistically high. But now, with the new aops, it has
become easy to hang on one machine.
Loop used to grab_cache_page before the old prepare_write to tmpfs, which
seems to have been enough to free up some memory for any swapin needed; but
the new write_begin lets tmpfs find or allocate the page (much nicer, since
grab_cache_page missed tmpfs pages in swapcache).
When allocating a fresh page, tmpfs respects loop's mapping_gfp_mask, which
has __GFP_IO|__GFP_FS stripped off, and throttle_vm_writeout is designed to
break out when __GFP_IO or GFP_FS is unset; but when tmfps swaps in,
read_swap_cache_async allocates with GFP_HIGHUSER_MOVABLE regardless of the
mapping_gfp_mask - hence the hang.
So, pass gfp_mask down the line from shmem_getpage to shmem_swapin to
swapin_readahead to read_swap_cache_async to add_to_swap_cache.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
swapin_readahead has never sat well in mm/memory.c: move it to mm/swap_state.c
beside its kindred read_swap_cache_async. Why were its args in a different
order? rearrange them. And since it was always followed by a
read_swap_cache_async of the target page, fold that in and return struct
page*. Then CONFIG_SWAP=n no longer needs valid_swaphandles and
read_swap_cache_async stubs.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For three years swapin_readahead has been cluttered with fanciful CONFIG_NUMA
code, advancing addr, and stepping on to the next vma at the boundary, to line
up the mempolicy for each page allocation.
It _might_ be a good idea to allocate swap more according to vma layout; but
the fact is, that's not how we do it at all, 2.6 even less than 2.4: swap is
allocated as needed for pages as they sink to the bottom of the inactive LRUs.
Sometimes that may match vma layout, but not so often that it's worth going
to these misleading vma->vm_next lengths: rip all that out.
Originally I intended to retain the incrementation of addr, but correct its
initial value: valid_swaphandles generally supplies an offset below the target
addr (this is readaround rather than readahead), but addr has not been
adjusted accordingly, so in the interleave case it has usually been allocating
the target page from the "wrong" node (though that may not matter very much).
But look at the equivalent shmem_swapin code: either by oversight or by
design, though it has all the apparatus for choosing a new mempolicy per page,
it uses the same idx throughout, choosing the same mempolicy and interleave
node for each page of the cluster.
Which is actually a much better strategy: each node has its own LRUs and its
own kswapd, so if you're betting on any particular relationship between swap
and node, the best bet is that nearby swap entries belong to pages from the
same node - even when the mempolicy of the target page is to interleave. And
examining a map of nodes corresponding to swap entries on a numa=fake system
bears this out. (We could later tweak swap allocation to make it even more
likely, but this patch is merely about removing cruft.)
So, neither adjust nor increment addr in swapin_readahead, and then
shmem_swapin can use it too; the pseudo-vma to pass policy need only be set up
once per cluster, and so few fields of pvma are used, let's skip the memset -
from shmem_alloc_page also.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
tmpfs was misconverted to __GFP_ZERO in 2.6.11. There's an unusual case in
which shmem_getpage receives the page from its caller instead of allocating.
We must cover this case by clear_highpage before SetPageUptodate, as before.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It's possible to provoke unionfs (not yet in mainline, though in mm and
some distros) to hit shmem_writepage's BUG_ON(page_mapped(page)). I expect
it's possible to provoke the 2.6.23 ecryptfs in the same way (but the
2.6.24 ecryptfs no longer calls lower level's ->writepage).
This came to light with the recent find that AOP_WRITEPAGE_ACTIVATE could
leak from tmpfs via write_cache_pages and unionfs to userspace. There's
already a fix (e423003028183df54f039dfda8b58c49e78c89d7 - writeback: don't
propagate AOP_WRITEPAGE_ACTIVATE) in the tree for that, and it's okay so
far as it goes; but insufficient because it doesn't address the underlying
issue, that shmem_writepage expects to be called only by vmscan (relying on
backing_dev_info capabilities to prevent the normal writeback path from
ever approaching it).
That's an increasingly fragile assumption, and ramdisk_writepage (the other
source of AOP_WRITEPAGE_ACTIVATEs) is already careful to check
wbc->for_reclaim before returning it. Make the same check in
shmem_writepage, thereby sidestepping the page_mapped BUG also.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Erez Zadok <ezk@cs.sunysb.edu>
Cc: <stable@kernel.org>
Reviewed-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now that nfsd has stopped writing to the find_exported_dentry member we an
mark the export_operations const
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Neil Brown <neilb@suse.de>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: <linux-ext4@vger.kernel.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: David Chinner <dgc@sgi.com>
Cc: Timothy Shimmin <tes@sgi.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Chris Mason <mason@suse.com>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: "Vladimir V. Saveliev" <vs@namesys.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I'm not sure what people were thinking when adding support to export tmpfs,
but here's the conversion anyway:
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Neil Brown <neilb@suse.de>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Why do we need r/o bind mounts?
This feature allows a read-only view into a read-write filesystem. In the
process of doing that, it also provides infrastructure for keeping track of
the number of writers to any given mount.
This has a number of uses. It allows chroots to have parts of filesystems
writable. It will be useful for containers in the future because users may
have root inside a container, but should not be allowed to write to
somefilesystems. This also replaces patches that vserver has had out of the
tree for several years.
It allows security enhancement by making sure that parts of your filesystem
read-only (such as when you don't trust your FTP server), when you don't want
to have entire new filesystems mounted, or when you want atime selectively
updated. I've been using the following script to test that the feature is
working as desired. It takes a directory and makes a regular bind and a r/o
bind mount of it. It then performs some normal filesystem operations on the
three directories, including ones that are expected to fail, like creating a
file on the r/o mount.
This patch:
Some filesystems forego the vfs and may_open() and create their own 'struct
file's.
This patch creates a couple of helper functions which can be used by these
filesystems, and will provide a unified place which the r/o bind mount code
may patch.
Also, rename an existing, static-scope init_file() to a less generic name.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
These aren't modular, so SLAB_PANIC is OK.
Signed-off-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Slab constructors currently have a flags parameter that is never used. And
the order of the arguments is opposite to other slab functions. The object
pointer is placed before the kmem_cache pointer.
Convert
ctor(void *object, struct kmem_cache *s, unsigned long flags)
to
ctor(struct kmem_cache *s, void *object)
throughout the kernel
[akpm@linux-foundation.org: coupla fixes]
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
provide BDI constructor/destructor hooks
[akpm@linux-foundation.org: compile fix]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch makes three needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch marks a number of allocations that are either short-lived such as
network buffers or are reclaimable such as inode allocations. When something
like updatedb is called, long-lived and unmovable kernel allocations tend to
be spread throughout the address space which increases fragmentation.
This patch groups these allocations together as much as possible by adding a
new MIGRATE_TYPE. The MIGRATE_RECLAIMABLE type is for allocations that can be
reclaimed on demand, but not moved. i.e. they can be migrated by deleting
them and re-reading the information from elsewhere.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Here's a cut at fixing up uses of the online node map in generic code.
mm/shmem.c:shmem_parse_mpol()
Ensure nodelist is subset of nodes with memory.
Use node_states[N_HIGH_MEMORY] as default for missing
nodelist for interleave policy.
mm/shmem.c:shmem_fill_super()
initialize policy_nodes to node_states[N_HIGH_MEMORY]
mm/page-writeback.c:highmem_dirtyable_memory()
sum over nodes with memory
mm/page_alloc.c:zlc_setup()
allowednodes - use nodes with memory.
mm/page_alloc.c:default_zonelist_order()
average over nodes with memory.
mm/page_alloc.c:find_next_best_node()
skip nodes w/o memory.
N_HIGH_MEMORY state mask may not be initialized at this time,
unless we want to depend on early_calculate_totalpages() [see
below]. Will ZONE_MOVABLE ever be configurable?
mm/page_alloc.c:find_zone_movable_pfns_for_nodes()
spread kernelcore over nodes with memory.
This required calling early_calculate_totalpages()
unconditionally, and populating N_HIGH_MEMORY node
state therein from nodes in the early_node_map[].
If we can depend on this, we can eliminate the
population of N_HIGH_MEMORY mask from __build_all_zonelists()
and use the N_HIGH_MEMORY mask in find_next_best_node().
mm/mempolicy.c:mpol_check_policy()
Ensure nodes specified for policy are subset of
nodes with memory.
[akpm@linux-foundation.org: fix warnings]
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Implement new aops for some of the simpler filesystems.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch cleans up duplicate includes in
mm/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Slab destructors were no longer supported after Christoph's
c59def9f222d44bb7e2f0a559f2906191a0862d7 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This patch completes Linus's wish that the fault return codes be made into
bit flags, which I agree makes everything nicer. This requires requires
all handle_mm_fault callers to be modified (possibly the modifications
should go further and do things like fault accounting in handle_mm_fault --
however that would be for another patch).
[akpm@linux-foundation.org: fix alpha build]
[akpm@linux-foundation.org: fix s390 build]
[akpm@linux-foundation.org: fix sparc build]
[akpm@linux-foundation.org: fix sparc64 build]
[akpm@linux-foundation.org: fix ia64 build]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Still apparently needs some ARM and PPC loving - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change ->fault prototype. We now return an int, which contains
VM_FAULT_xxx code in the low byte, and FAULT_RET_xxx code in the next byte.
FAULT_RET_ code tells the VM whether a page was found, whether it has been
locked, and potentially other things. This is not quite the way he wanted
it yet, but that's changed in the next patch (which requires changes to
arch code).
This means we no longer set VM_CAN_INVALIDATE in the vma in order to say
that a page is locked which requires filemap_nopage to go away (because we
can no longer remain backward compatible without that flag), but we were
going to do that anyway.
struct fault_data is renamed to struct vm_fault as Linus asked. address
is now a void __user * that we should firmly encourage drivers not to use
without really good reason.
The page is now returned via a page pointer in the vm_fault struct.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Nonlinear mappings are (AFAIKS) simply a virtual memory concept that encodes
the virtual address -> file offset differently from linear mappings.
->populate is a layering violation because the filesystem/pagecache code
should need to know anything about the virtual memory mapping. The hitch here
is that the ->nopage handler didn't pass down enough information (ie. pgoff).
But it is more logical to pass pgoff rather than have the ->nopage function
calculate it itself anyway (because that's a similar layering violation).
Having the populate handler install the pte itself is likewise a nasty thing
to be doing.
This patch introduces a new fault handler that replaces ->nopage and
->populate and (later) ->nopfn. Most of the old mechanism is still in place
so there is a lot of duplication and nice cleanups that can be removed if
everyone switches over.
The rationale for doing this in the first place is that nonlinear mappings are
subject to the pagefault vs invalidate/truncate race too, and it seemed stupid
to duplicate the synchronisation logic rather than just consolidate the two.
After this patch, MAP_NONBLOCK no longer sets up ptes for pages present in
pagecache. Seems like a fringe functionality anyway.
NOPAGE_REFAULT is removed. This should be implemented with ->fault, and no
users have hit mainline yet.
[akpm@linux-foundation.org: cleanup]
[randy.dunlap@oracle.com: doc. fixes for readahead]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the race between invalidate_inode_pages and do_no_page.
Andrea Arcangeli identified a subtle race between invalidation of pages from
pagecache with userspace mappings, and do_no_page.
The issue is that invalidation has to shoot down all mappings to the page,
before it can be discarded from the pagecache. Between shooting down ptes to
a particular page, and actually dropping the struct page from the pagecache,
do_no_page from any process might fault on that page and establish a new
mapping to the page just before it gets discarded from the pagecache.
The most common case where such invalidation is used is in file truncation.
This case was catered for by doing a sort of open-coded seqlock between the
file's i_size, and its truncate_count.
Truncation will decrease i_size, then increment truncate_count before
unmapping userspace pages; do_no_page will read truncate_count, then find the
page if it is within i_size, and then check truncate_count under the page
table lock and back out and retry if it had subsequently been changed (ptl
will serialise against unmapping, and ensure a potentially updated
truncate_count is actually visible).
Complexity and documentation issues aside, the locking protocol fails in the
case where we would like to invalidate pagecache inside i_size. do_no_page
can come in anytime and filemap_nopage is not aware of the invalidation in
progress (as it is when it is outside i_size). The end result is that
dangling (->mapping == NULL) pages that appear to be from a particular file
may be mapped into userspace with nonsense data. Valid mappings to the same
place will see a different page.
Andrea implemented two working fixes, one using a real seqlock, another using
a page->flags bit. He also proposed using the page lock in do_no_page, but
that was initially considered too heavyweight. However, it is not a global or
per-file lock, and the page cacheline is modified in do_no_page to increment
_count and _mapcount anyway, so a further modification should not be a large
performance hit. Scalability is not an issue.
This patch implements this latter approach. ->nopage implementations return
with the page locked if it is possible for their underlying file to be
invalidated (in that case, they must set a special vm_flags bit to indicate
so). do_no_page only unlocks the page after setting up the mapping
completely. invalidation is excluded because it holds the page lock during
invalidation of each page (and ensures that the page is not mapped while
holding the lock).
This also allows significant simplifications in do_no_page, because we have
the page locked in the right place in the pagecache from the start.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
currently the export_operation structure and helpers related to it are in
fs.h. fs.h is already far too large and there are very few places needing the
export bits, so split them off into a separate header.
[akpm@linux-foundation.org: fix cifs build]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
be migrated
It is often known at allocation time whether a page may be migrated or not.
This patch adds a flag called __GFP_MOVABLE and a new mask called
GFP_HIGH_MOVABLE. Allocations using the __GFP_MOVABLE can be either migrated
using the page migration mechanism or reclaimed by syncing with backing
storage and discarding.
An API function very similar to alloc_zeroed_user_highpage() is added for
__GFP_MOVABLE allocations called alloc_zeroed_user_highpage_movable(). The
flags used by alloc_zeroed_user_highpage() are not changed because it would
change the semantics of an existing API. After this patch is applied there
are no in-kernel users of alloc_zeroed_user_highpage() so it probably should
be marked deprecated if this patch is merged.
Note that this patch includes a minor cleanup to the use of __GFP_ZERO in
shmem.c to keep all flag modifications to inode->mapping in the
shmem_dir_alloc() helper function. This clean-up suggestion is courtesy of
Hugh Dickens.
Additional credit goes to Christoph Lameter and Linus Torvalds for shaping the
concept. Credit to Hugh Dickens for catching issues with shmem swap vector
and ramfs allocations.
[akpm@linux-foundation.org: build fix]
[hugh@veritas.com: __GFP_ZERO cleanup]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove shmem_file_sendfile and resurrect shmem_readpage, as used by tmpfs
to support loop and sendfile in 2.4 and 2.5. Now tmpfs can support splice,
loop and sendfile in the simplest way, using generic_file_splice_read and
generic_file_splice_write (with the aid of shmem_prepare_write).
We could make some efficiency tweaks later, if there's a real need;
but this is stable and works well as is.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Randy Dunlap reports that a tmpfs, mounted with NUMA mpol= specifying an
offline node, crashes as soon as data is allocated upon it. Now restrict it
to online nodes, where before it restricted to MAX_NUMNODES.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Tested-and-acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
SLAB_CTOR_CONSTRUCTOR is always specified. No point in checking it.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Steven French <sfrench@us.ibm.com>
Cc: Michael Halcrow <mhalcrow@us.ibm.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dave Kleikamp <shaggy@austin.ibm.com>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Anton Altaparmakov <aia21@cantab.net>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@ucw.cz>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I have never seen a use of SLAB_DEBUG_INITIAL. It is only supported by
SLAB.
I think its purpose was to have a callback after an object has been freed
to verify that the state is the constructor state again? The callback is
performed before each freeing of an object.
I would think that it is much easier to check the object state manually
before the free. That also places the check near the code object
manipulation of the object.
Also the SLAB_DEBUG_INITIAL callback is only performed if the kernel was
compiled with SLAB debugging on. If there would be code in a constructor
handling SLAB_DEBUG_INITIAL then it would have to be conditional on
SLAB_DEBUG otherwise it would just be dead code. But there is no such code
in the kernel. I think SLUB_DEBUG_INITIAL is too problematic to make real
use of, difficult to understand and there are easier ways to accomplish the
same effect (i.e. add debug code before kfree).
There is a related flag SLAB_CTOR_VERIFY that is frequently checked to be
clear in fs inode caches. Remove the pointless checks (they would even be
pointless without removeal of SLAB_DEBUG_INITIAL) from the fs constructors.
This is the last slab flag that SLUB did not support. Remove the check for
unimplemented flags from SLUB.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
