| Age | Commit message (Collapse) | Author |
|---|
|
Conflicts:
drivers/net/wimax/i2400m/usb-notif.c
|
|
dpm_list currently relies on the fact that child devices will
be registered after their parents to get a correct suspend
order. Using device_move() however destroys this assumption, as
an already registered device may be moved under a newly registered
one.
This patch adds a new argument to device_move(), allowing callers
to specify how dpm_list should be adapted.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The CID value of L2CAP sockets need to be set to zero. All userspace
applications do this via memset() on the sockaddr_l2 structure. The
RFCOMM implementation uses in-kernel L2CAP sockets and so it has to
make sure that l2_cid is set to zero.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When BT_DEFER_SETUP is enabled on a RFCOMM socket, then switch its
current state from BT_OPEN to BT_CONNECT2. This gives the Bluetooth
core a unified way to handle L2CAP and RFCOMM sockets. The BT_CONNECT2
state is designated for incoming connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When receiving incoming connection to specific services, always use
general bonding. This ensures that the link key gets stored and can be
used for further authentications.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
During a role change with pre-Bluetooth 2.1 devices, the remote side drops
the encryption of the RFCOMM connection. We allow a grace period for the
encryption to be re-established, before dropping the connection. During
this grace period, the RFCOMM_SEC_PENDING flag is set. Check this flag
before sending RFCOMM packets.
Signed-off-by: Jaikumar Ganesh <jaikumar@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
With the support for the enhanced security model and the support for
deferring connection setup, it is a good idea to increase various
version numbers.
This is purely cosmetic and has no effect on the behavior, but can
be really helpful when debugging problems in different kernel versions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The new socket options should only be evaluated for SOL_BLUETOOTH level
and not for every other level. Previously this causes some minor issues
when detecting if a kernel with certain features is available.
Also restrict BT_SECURITY to SOCK_SEQPACKET for L2CAP and SOCK_STREAM for
the RFCOMM protocol.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
A role switch with devices following the Bluetooth pre-2.1 standards
or without Encryption Pause and Resume support is not possible if
encryption is enabled. Most newer headsets require the role switch,
but also require that the connection is encrypted.
For connections with a high security mode setting, the link will be
immediately dropped. When the connection uses medium security mode
setting, then a grace period is introduced where the TX is halted and
the remote device gets a change to re-enable encryption after the
role switch. If not re-enabled the link will be dropped.
Based on initial work by Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Change the RFCOMM internals to use the new security levels and remove
the link mode details.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The current security model is based around the flags AUTH, ENCRYPT and
SECURE. Starting with support for the Bluetooth 2.1 specification this is
no longer sufficient. The different security levels are now defined as
SDP, LOW, MEDIUM and SECURE.
Previously it was possible to set each security independently, but this
actually doesn't make a lot of sense. For Bluetooth the encryption depends
on a previous successful authentication. Also you can only update your
existing link key if you successfully created at least one before. And of
course the update of link keys without having proper encryption in place
is a security issue.
The new security levels from the Bluetooth 2.1 specification are now
used internally. All old settings are mapped to the new values and this
way it ensures that old applications still work. The only limitation
is that it is no longer possible to set authentication without also
enabling encryption. No application should have done this anyway since
this is actually a security issue. Without encryption the integrity of
the authentication can't be guaranteed.
As default for a new L2CAP or RFCOMM connection, the LOW security level
is used. The only exception here are the service discovery sessions on
PSM 1 where SDP level is used. To have similar security strength as with
a Bluetooth 2.0 and before combination key, the MEDIUM level should be
used. This is according to the Bluetooth specification. The MEDIUM level
will not require any kind of man-in-the-middle (MITM) protection. Only
the HIGH security level will require this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In order to decide if listening RFCOMM sockets should be accept()ed
the BD_ADDR of the remote device needs to be known. This patch adds
a socket option which defines a timeout for deferring the actual
connection setup.
The connection setup is done after reading from the socket for the
first time. Until then writing to the socket returns ENOTCONN.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The socket option levels SOL_L2CAP, SOL_RFOMM and SOL_SCO are currently
in use by various Bluetooth applications. Going forward the common
option level SOL_BLUETOOTH should be used. This patch prepares the clean
split of the old and new option levels while keeping everything backward
compatibility.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In case of connection failures the rfcomm_sock_sendmsg() should return
an error and not a 0 value.
Signed-off-by: Victor Shcherbatyuk <victor.shcherbatyuk@tomtom.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/ppp_generic.c
|
|
The kernel_accept() does not hold the module refcount of newsock->ops->owner,
so we need __module_get(newsock->ops->owner) code after call kernel_accept()
by hand.
In sunrpc, the module refcount is missing to hold. So this cause kernel panic.
Used following script to reproduct:
while [ 1 ];
do
mount -t nfs4 192.168.0.19:/ /mnt
touch /mnt/file
umount /mnt
lsmod | grep ipv6
done
This patch fixed the problem by add __module_get(newsock->ops->owner) to
kernel_accept(). So we do not need to used __module_get(newsock->ops->owner)
in every place when used kernel_accept().
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Stephen Rothwell points out, we don't want 'sock' here but
rather we really do want 'sk'.
This local var is protected by all sorts of bluetooth debugging
kconfig vars, but BT_DBG() is just a straight pr_debug() call
which is unconditional.
pr_debug() evaluates it's args only if either DEBUG or
CONFIG_DYNAMIC_PRINTK_DEBUG is defined.
Solving this inside of the BT_DBG() macro is non-trivial since
it's varargs. And these ifdefs are ugly.
So, just mark this 'sk' thing __maybe_unused and kill the ifdefs.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's 'sock' not 'sk'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turns out that the following sequence of actions will reproduce the
oops:
1. Create a new RFCOMM device (using RFCOMMCREATEDEV ioctl)
2. (Try to) open the device
3. Release the RFCOMM device (using RFCOMMRELEASEDEV ioctl)
At this point, the "/dev/rfcomm*" device is still in use, but it is gone
from the internal list, so the device id can be reused.
4. Create a new RFCOMM device with the same device id as before
And now kobject will complain that the TTY already exists.
(See http://lkml.org/lkml/2008/7/13/89 for a reproducible test-case.)
This patch attempts to correct this by only removing the device from the
internal list of devices at the final unregister stage, so that the id
won't get reused until the device has been completely destructed.
This should be safe as the RFCOMM_TTY_RELEASED bit will be set for the
device and prevent the device from being reopened after it has been
released.
Based on a report from Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
With the introduction of CONFIG_DYNAMIC_PRINTK_DEBUG it is possible to
allow debugging without having to recompile the kernel. This patch turns
all BT_DBG() calls into pr_debug() to support dynamic debug messages.
As a side effect all CONFIG_BT_*_DEBUG statements are now removed and
some broken debug entries have been fixed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
fix this warning:
net/bluetooth/rfcomm/sock.c: In function ‘rfcomm_sock_ioctl’:
net/bluetooth/rfcomm/sock.c:795: warning: unused variable ‘sk’
perhaps BT_DEBUG() should be improved to do printf format checking
instead of the #ifdef, but that looks quite intrusive: each bluetooth
.c file undefines the macro.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Bluetooth entries for the MAINTAINERS file are a little bit too
much. Consolidate them into two entries. One for Bluetooth drivers and
another one for the Bluetooth subsystem.
Also the MODULE_AUTHOR should indicate the current maintainer of the
module and actually not the original author. Fix all Bluetooth modules
to provide current maintainer information.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (1232 commits)
iucv: Fix bad merging.
net_sched: Add size table for qdiscs
net_sched: Add accessor function for packet length for qdiscs
net_sched: Add qdisc_enqueue wrapper
highmem: Export totalhigh_pages.
ipv6 mcast: Omit redundant address family checks in ip6_mc_source().
net: Use standard structures for generic socket address structures.
ipv6 netns: Make several "global" sysctl variables namespace aware.
netns: Use net_eq() to compare net-namespaces for optimization.
ipv6: remove unused macros from net/ipv6.h
ipv6: remove unused parameter from ip6_ra_control
tcp: fix kernel panic with listening_get_next
tcp: Remove redundant checks when setting eff_sacks
tcp: options clean up
tcp: Fix MD5 signatures for non-linear skbs
sctp: Update sctp global memory limit allocations.
sctp: remove unnecessary byteshifting, calculate directly in big-endian
sctp: Allow only 1 listening socket with SO_REUSEADDR
sctp: Do not leak memory on multiple listen() calls
sctp: Support ipv6only AF_INET6 sockets.
...
|
|
Move the line disciplines towards a conventional ->ops arrangement. For
the moment the actual 'tty_ldisc' struct in the tty is kept as part of
the tty struct but this can then be changed if it turns out that when it
all settles down we want to refcount ldiscs separately to the tty.
Pull the ldisc code out of /proc and put it with our ldisc code.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/holtmann/bluetooth-2.6
|
|
When an incoming RFCOMM socket connection gets converted into a TTY,
it can happen that packets are lost. This mainly happens with the
Handsfree profile where the remote side starts sending data right
away. The problem is that these packets are in the socket receive
queue. So when creating the TTY make sure to copy all pending packets
from the socket receive queue to a private queue inside the TTY.
To make this actually work, the flow control on the newly created TTY
will be disabled and only enabled again when the TTY is opened by an
application. And right before that, the pending packets will be put
into the TTY flip buffer.
Signed-off-by: Denis Kenzior <denis.kenzior@trolltech.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When switching a RFCOMM socket to a TTY, the remote modem status might
be needed later. Currently it is lost since the original configuration
is done via the socket interface. So store the modem status and reply
it when the socket has been converted to a TTY.
Signed-off-by: Denis Kenzior <denis.kenzior@trolltech.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
While the RFCOMM TTY emulation can act like a real serial port, in
reality it is not used like this. So to not mess up stupid applications,
use the non-canonical mode by default.
Signed-off-by: Denis Kenzior <denis.kenzior@trolltech.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Enable the common timestamp functionality that the network subsystem
provides for L2CAP, RFCOMM and SCO sockets. It is possible to either
use SO_TIMESTAMP or the IOCTLs to retrieve the timestamp of the
current packet.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
With the Simple Pairing support, the authentication requirements are
an explicit setting during the bonding process. Track and enforce the
requirements and allow higher layers like L2CAP and RFCOMM to increase
them if needed.
This patch introduces a new IOCTL that allows to query the current
authentication requirements. It is also possible to detect Simple
Pairing support in the kernel this way.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Bluetooth specification allows to enable or disable the encryption
of an ACL link at any time by either the peer or the remote device. If
a L2CAP or RFCOMM connection requested an encrypted link, they will now
disconnect that link if the encryption gets disabled. Higher protocols
that don't care about encryption (like SDP) are not affected.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Recent tests with various Bluetooth headsets have shown that some of
them don't enforce authentication and encryption when connecting. All
of them leave it up to the host stack to enforce it. Non of them should
allow unencrypted connections, but that is how it is. So in case the
link mode settings require authentication and/or encryption it will now
also be enforced on outgoing RFCOMM connections. Previously this was
only done for incoming connections.
This support has a small drawback from a protocol level point of view
since the host stack can't really tell with 100% certainty if a remote
side is already authenticated or not. So if both sides are configured
to enforce authentication it will be requested twice. Most Bluetooth
chips are caching this information and thus no extra authentication
procedure has to be triggered over-the-air, but it can happen.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch removes CVS keywords that weren't updated for a long time
from comments.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's logic in __rfcomm_dlc_close:
rfcomm_dlc_lock(d);
d->state = BT_CLOSED;
d->state_changed(d, err);
rfcomm_dlc_unlock(d);
In rfcomm_dev_state_change, it's possible that rfcomm_dev_put try to
take the dlc lock, then we will deadlock.
Here fixed it by unlock dlc before rfcomm_dev_get in
rfcomm_dev_state_change.
why not unlock just before rfcomm_dev_put? it's because there's
another problem. rfcomm_dev_get/rfcomm_dev_del will take
rfcomm_dev_lock, but in rfcomm_dev_add the lock order is :
rfcomm_dev_lock --> dlc lock
so I unlock dlc before the taken of rfcomm_dev_lock.
Actually it's a regression caused by commit
1905f6c736cb618e07eca0c96e60e3c024023428 ("bluetooth :
__rfcomm_dlc_close lock fix"), the dlc state_change could be two
callbacks : rfcomm_sk_state_change and rfcomm_dev_state_change. I
missed the rfcomm_sk_state_change that time.
Thanks Arjan van de Ven <arjan@linux.intel.com> for the effort in
commit 4c8411f8c115def968820a4df6658ccfd55d7f1a ("bluetooth: fix
locking bug in the rfcomm socket cleanup handling") but he missed the
rfcomm_dev_state_change lock issue.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
in net/bluetooth/rfcomm/sock.c, rfcomm_sk_state_change() does the
following operation:
if (parent && sock_flag(sk, SOCK_ZAPPED)) {
/* We have to drop DLC lock here, otherwise
* rfcomm_sock_destruct() will dead lock. */
rfcomm_dlc_unlock(d);
rfcomm_sock_kill(sk);
rfcomm_dlc_lock(d);
}
}
which is fine, since rfcomm_sock_kill() will call sk_free() which will call
rfcomm_sock_destruct() which takes the rfcomm_dlc_lock()... so far so good.
HOWEVER, this assumes that the rfcomm_sk_state_change() function always gets
called with the rfcomm_dlc_lock() taken. This is the case for all but one
case, and in that case where we don't have the lock, we do a double unlock
followed by an attempt to take the lock, which due to underflow isn't
going anywhere fast.
This patch fixes this by moving the stragling case inside the lock, like
the other usages of the same call are doing in this code.
This was found with the help of the www.kerneloops.org project, where this
deadlock was observed 51 times at this point in time:
http://www.kerneloops.org/search.php?search=rfcomm_sock_destruct
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/s2io.c
|
|
Lockdep warning will be trigged while rfcomm connection closing.
The locks taken in rfcomm_dev_add:
rfcomm_dev_lock --> d->lock
In __rfcomm_dlc_close:
d->lock --> rfcomm_dev_lock (in rfcomm_dev_state_change)
There's two way to fix it, one is in rfcomm_dev_add we first locking
d->lock then the rfcomm_dev_lock
The other (in this patch), remove the locking of d->lock for
rfcomm_dev_state_change because just locking "d->state = BT_CLOSED;"
is enough.
[ 295.002046] =======================================================
[ 295.002046] [ INFO: possible circular locking dependency detected ]
[ 295.002046] 2.6.25-rc7 #1
[ 295.002046] -------------------------------------------------------
[ 295.002046] krfcommd/2705 is trying to acquire lock:
[ 295.002046] (rfcomm_dev_lock){-.--}, at: [<f89a090a>] rfcomm_dev_state_change+0x6a/0xd0 [rfcomm]
[ 295.002046]
[ 295.002046] but task is already holding lock:
[ 295.002046] (&d->lock){--..}, at: [<f899c533>] __rfcomm_dlc_close+0x43/0xd0 [rfcomm]
[ 295.002046]
[ 295.002046] which lock already depends on the new lock.
[ 295.002046]
[ 295.002046]
[ 295.002046] the existing dependency chain (in reverse order) is:
[ 295.002046]
[ 295.002046] -> #1 (&d->lock){--..}:
[ 295.002046] [<c0149b23>] check_prev_add+0xd3/0x200
[ 295.002046] [<c0149ce5>] check_prevs_add+0x95/0xe0
[ 295.002046] [<c0149f6f>] validate_chain+0x23f/0x320
[ 295.002046] [<c014b7b1>] __lock_acquire+0x1c1/0x760
[ 295.002046] [<c014c349>] lock_acquire+0x79/0xb0
[ 295.002046] [<c03d6b99>] _spin_lock+0x39/0x80
[ 295.002046] [<f89a01c0>] rfcomm_dev_add+0x240/0x360 [rfcomm]
[ 295.002046] [<f89a047e>] rfcomm_create_dev+0x6e/0xe0 [rfcomm]
[ 295.002046] [<f89a0823>] rfcomm_dev_ioctl+0x33/0x60 [rfcomm]
[ 295.002046] [<f899facc>] rfcomm_sock_ioctl+0x2c/0x50 [rfcomm]
[ 295.002046] [<c0363d38>] sock_ioctl+0x118/0x240
[ 295.002046] [<c0194196>] vfs_ioctl+0x76/0x90
[ 295.002046] [<c0194446>] do_vfs_ioctl+0x56/0x140
[ 295.002046] [<c0194569>] sys_ioctl+0x39/0x60
[ 295.002046] [<c0104faa>] syscall_call+0x7/0xb
[ 295.002046] [<ffffffff>] 0xffffffff
[ 295.002046]
[ 295.002046] -> #0 (rfcomm_dev_lock){-.--}:
[ 295.002046] [<c0149a84>] check_prev_add+0x34/0x200
[ 295.002046] [<c0149ce5>] check_prevs_add+0x95/0xe0
[ 295.002046] [<c0149f6f>] validate_chain+0x23f/0x320
[ 295.002046] [<c014b7b1>] __lock_acquire+0x1c1/0x760
[ 295.002046] [<c014c349>] lock_acquire+0x79/0xb0
[ 295.002046] [<c03d6639>] _read_lock+0x39/0x80
[ 295.002046] [<f89a090a>] rfcomm_dev_state_change+0x6a/0xd0 [rfcomm]
[ 295.002046] [<f899c548>] __rfcomm_dlc_close+0x58/0xd0 [rfcomm]
[ 295.002046] [<f899d44f>] rfcomm_recv_ua+0x6f/0x120 [rfcomm]
[ 295.002046] [<f899e061>] rfcomm_recv_frame+0x171/0x1e0 [rfcomm]
[ 295.002046] [<f899e357>] rfcomm_run+0xe7/0x550 [rfcomm]
[ 295.002046] [<c013c18c>] kthread+0x5c/0xa0
[ 295.002046] [<c0105c07>] kernel_thread_helper+0x7/0x10
[ 295.002046] [<ffffffff>] 0xffffffff
[ 295.002046]
[ 295.002046] other info that might help us debug this:
[ 295.002046]
[ 295.002046] 2 locks held by krfcommd/2705:
[ 295.002046] #0: (rfcomm_mutex){--..}, at: [<f899e2eb>] rfcomm_run+0x7b/0x550 [rfcomm]
[ 295.002046] #1: (&d->lock){--..}, at: [<f899c533>] __rfcomm_dlc_close+0x43/0xd0 [rfcomm]
[ 295.002046]
[ 295.002046] stack backtrace:
[ 295.002046] Pid: 2705, comm: krfcommd Not tainted 2.6.25-rc7 #1
[ 295.002046] [<c0128a38>] ? printk+0x18/0x20
[ 295.002046] [<c014927f>] print_circular_bug_tail+0x6f/0x80
[ 295.002046] [<c0149a84>] check_prev_add+0x34/0x200
[ 295.002046] [<c0149ce5>] check_prevs_add+0x95/0xe0
[ 295.002046] [<c0149f6f>] validate_chain+0x23f/0x320
[ 295.002046] [<c014b7b1>] __lock_acquire+0x1c1/0x760
[ 295.002046] [<c014c349>] lock_acquire+0x79/0xb0
[ 295.002046] [<f89a090a>] ? rfcomm_dev_state_change+0x6a/0xd0 [rfcomm]
[ 295.002046] [<c03d6639>] _read_lock+0x39/0x80
[ 295.002046] [<f89a090a>] ? rfcomm_dev_state_change+0x6a/0xd0 [rfcomm]
[ 295.002046] [<f89a090a>] rfcomm_dev_state_change+0x6a/0xd0 [rfcomm]
[ 295.002046] [<f899c548>] __rfcomm_dlc_close+0x58/0xd0 [rfcomm]
[ 295.002046] [<f899d44f>] rfcomm_recv_ua+0x6f/0x120 [rfcomm]
[ 295.002046] [<f899e061>] rfcomm_recv_frame+0x171/0x1e0 [rfcomm]
[ 295.002046] [<c014abd9>] ? trace_hardirqs_on+0xb9/0x130
[ 295.002046] [<c03d6e89>] ? _spin_unlock_irqrestore+0x39/0x70
[ 295.002046] [<f899e357>] rfcomm_run+0xe7/0x550 [rfcomm]
[ 295.002046] [<c03d4559>] ? __sched_text_start+0x229/0x4c0
[ 295.002046] [<c0120000>] ? cpu_avg_load_per_task+0x20/0x30
[ 295.002046] [<f899e270>] ? rfcomm_run+0x0/0x550 [rfcomm]
[ 295.002046] [<c013c18c>] kthread+0x5c/0xa0
[ 295.002046] [<c013c130>] ? kthread+0x0/0xa0
[ 295.002046] [<c0105c07>] kernel_thread_helper+0x7/0x10
[ 295.002046] =======================
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The older RW_LOCK_UNLOCKED macros defeat lockdep state tracing so
replace them with the newer __RW_LOCK_UNLOCKED macros.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce per-sock inlines: sock_net(), sock_net_set()
and per-inet_timewait_sock inlines: twsk_net(), twsk_net_set().
Without CONFIG_NET_NS, no namespace other than &init_net exists.
Let's explicitly define them to help compiler optimizations.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
|
|
fastcall always expands to empty, remove it.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
rfcomm dev could be deleted in tty_hangup, so we must not call
rfcomm_dev_del again to prevent from destroying rfcomm dev before tty
close.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many-many code in the kernel initialized the timer->function
and timer->data together with calling init_timer(timer). There
is already a helper for this. Use it for networking code.
The patch is HUGE, but makes the code 130 lines shorter
(98 insertions(+), 228 deletions(-)).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The rfcomm tty device will possibly retain even when conn is down, and
sysfs doesn't support zombie device moving, so this patch move the tty
device before conn device is destroyed.
For the bug refered please see :
http://lkml.org/lkml/2007/12/28/87
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) In tty.c the BUG_ON at line 115 will never be called, because the the
before list_del_init in this same function.
115 BUG_ON(!list_empty(&dev->list));
So move the list_del_init to rfcomm_dev_del
2) The rfcomm_dev_del could be called from diffrent path
(rfcomm_tty_hangup/rfcomm_dev_state_change/rfcomm_release_dev),
So add another BUG_ON when the rfcomm_dev_del is called more than
one time.
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Finally, the zero_it argument can be completely removed from
the callers and from the function prototype.
Besides, fix the checkpatch.pl warnings about using the
assignments inside if-s.
This patch is rather big, and it is a part of the previous one.
I splitted it wishing to make the patches more readable. Hope
this particular split helped.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch does the full kthread conversion for the RFCOMM protocol. It
makes the code slightly simpler and more maintainable.
Based on a patch from Christoph Hellwig <hch@lst.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Export the remote device address and channel of RFCOMM TTY device
via sysfs attributes. This allows udev to create better naming rules
for configured RFCOMM devices.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch passes in the namespace a new socket should be created in
and has the socket code do the appropriate reference counting. By
virtue of this all socket create methods are touched. In addition
the socket create methods are modified so that they will fail if
you attempt to create a socket in a non-default network namespace.
Failing if we attempt to create a socket outside of the default
network namespace ensures that as we incrementally make the network stack
network namespace aware we will not export functionality that someone
has not audited and made certain is network namespace safe.
Allowing us to partially enable network namespaces before all of the
exotic protocols are supported.
Any protocol layers I have missed will fail to compile because I now
pass an extra parameter into the socket creation code.
[ Integrated AF_IUCV build fixes from Andrew Morton... -DaveM ]
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adrian Bunk wrote:
> Commit 8de0a15483b357d0f0b821330ec84d1660cadc4e added the following
> use-after-free in net/bluetooth/rfcomm/tty.c:
>
> <-- snip -->
>
> ...
> static int rfcomm_dev_add(struct rfcomm_dev_req *req, struct rfcomm_dlc *dlc)
> {
> ...
> if (IS_ERR(dev->tty_dev)) {
> list_del(&dev->list);
> kfree(dev);
> return PTR_ERR(dev->tty_dev);
> }
> ...
>
> <-- snip -->
>
> Spotted by the Coverity checker.
really good catch. I fully overlooked that one. The attached patch
should fix it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
