Age | Commit message (Collapse) | Author |
|
The allowed values for the key->master parameter in the Load LTKs
command are 0x00 and 0x01. If there is a key in the list with some other
value the command should fail with a proper invalid params response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Failures of mgmt commands should be indicated with valid mgmt status
codes, and EINVAL is not one of them. Instead MGMT_STATUS_INVALID_PARAMS
should be returned.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
The debug_keys parameter is only allowed to have the values 0x00 and
0x01. Any other value should result in a proper command status with
MGMT_STATUS_INVALID_PARAMS.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
According to Bluetooth Management API specification Pair Device Command
should generate command complete event on both success and failure.
This fix replying with command status (which lacks address info) when
adapter is powered off.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
When a HCI device is powered off the Management interface specification
dictates that the class of device value is indicated as zero. This patch
fixes sending of the appropriate class of device changed event when a
HCI device is powered off.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
The option allows you to remove TTY and compile without errors. This
saves space on systems that won't support TTY interfaces anyway.
bloat-o-meter output is below.
The bulk of this patch consists of Kconfig changes adding "depends on
TTY" to various serial devices and similar drivers that require the TTY
layer. Ideally, these dependencies would occur on a common intermediate
symbol such as SERIO, but most drivers "select SERIO" rather than
"depends on SERIO", and "select" does not respect dependencies.
bloat-o-meter output comparing our previous minimal to new minimal by
removing TTY. The list is filtered to not show removed entries with awk
'$3 != "-"' as the list was very long.
add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350)
function old new delta
chr_dev_init 166 170 +4
allow_signal 80 82 +2
static.__warned 143 142 -1
disallow_signal 63 62 -1
__set_special_pids 95 94 -1
unregister_console 126 121 -5
start_kernel 546 541 -5
register_console 593 588 -5
copy_from_user 45 40 -5
sys_setsid 128 120 -8
sys_vhangup 32 19 -13
do_exit 1543 1526 -17
bitmap_zero 60 40 -20
arch_local_irq_save 137 117 -20
release_task 674 652 -22
static.spin_unlock_irqrestore 308 260 -48
Signed-off-by: Joe Millenbach <jmillenbach@gmail.com>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There's a per-HCI device workqueue (hdev->workqueue) that should be used
for general per-HCI device work (except hdev->req_workqueue that's for
hci_request() related work). This patch fixes places using the
system-global work queue and makes them use the hdev->workqueue instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
This patch converts work assignment relying on hci_request() from the
system-global work queue to the per-HCI device specific work queue
(hdev->req_workqueue) intended for hci_request() related tasks.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
The hci_request function is blocking and cannot be called through the
usual per-HCI device workqueue (hdev->workqueue). While hci_request is
in progress any other work from the queue, including sending HCI
commands to the controller would be blocked and eventually cause the
hci_request call to time out.
This patch adds a second workqueue to be used by operations needing
hci_request and thereby avoiding issues with blocking other workqueue
users.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_string this time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The uuid should be printed in the CPU endianness and not in little-endian.
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
The socket from which a mgmt_set_powered command was received should
only receive the command response but no new_settings event.
The mgmt_powered() function which is used to handle the situation with
the HCI_AUTO_OFF flag tries to check for a pending command to know which
socket to skip the event for, but since the pending command hasn't been
added this will not happen.
This patch fixes the issue by adding the pending command for the
HCI_AUTO_OFF case and thereby ensures that mgmt_powered() will skip the
right socket when sending the new_settings event, but still send the
proper response to the socket where the command came from.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Management commands should whenever possible fail with proper command
status or command complete events. This patch fixes the
mgmt_start_discovery command to do this for the failure cases where an
incorrect parameter value was passed to it ("not supported" if the
parameter value was valid but the controller doesn't support it and
"invalid params" if it isn't valid at all).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
All mgmt_set_* commands that take a boolean value encoded in the form of
a byte should only accept the values 0x00 and 0x01. This patch adds the
necessary checks for this and returns "invalid params" responses if
anything else is provided as the value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
This patch fixes sections of code that do not need hci_lock_dev to be
outside of the lock. Such sections include code that do not touch the
hdev at all as well as sections which just read a single byte from the
supported_features value (i.e. all lmp_*_capable() macros).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
The concept of Class of Device only exists for BR/EDR controllers. The
mgmt_set_dev_class command should therefore return a proper "not
supported" error if it is attempted for a controller that doesn't
support BR/EDR (e.g. a single mode LE-only one).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
The two lowest bits of the minor device class value are reserved and
should be zero, and the three highest bits of the major device class
likewise. The management code should therefore test for this and return
a proper "invalid params" error if the condition is not met.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
All management events are expected to indicate successful completion
through a command complete event, however the load long term keys
command was missing this. This patch adds the missing event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
All management commands are expected to indicate successful completion
through a command complete event however the confirm name command was
missing it. This patch add the sending of the missing event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Checking only for sco_conn seems to not be enough and lead to NULL
dereferences in the code, check for hcon instead.
<1>[11340.226404] BUG: unable to handle kernel NULL pointer dereference at
0000000
8
<4>[11340.226619] EIP is at __sco_sock_close+0xe8/0x1a0
<4>[11340.226629] EAX: f063a740 EBX: 00000000 ECX: f58f4544 EDX: 00000000
<4>[11340.226640] ESI: dec83e00 EDI: 5f9a081f EBP: e0fdff38 ESP: e0fdff1c
<0>[11340.226674] Stack:
<4>[11340.226682] c184db87 c1251028 dec83e00 e0fdff38 c1754aef dec83e00
00000000
e0fdff5c
<4>[11340.226718] c184f587 e0fdff64 e0fdff68 5f9a081f e0fdff5c c1751852
d7813800
62262f10
<4>[11340.226752] e0fdff70 c1753c00 00000000 00000001 0000000d e0fdffac
c175425c
00000041
<0>[11340.226793] Call Trace:
<4>[11340.226813] [<c184db87>] ? sco_sock_clear_timer+0x27/0x60
<4>[11340.226831] [<c1251028>] ? local_bh_enable+0x68/0xd0
<4>[11340.226846] [<c1754aef>] ? lock_sock_nested+0x4f/0x60
<4>[11340.226862] [<c184f587>] sco_sock_shutdown+0x67/0xb0
<4>[11340.226879] [<c1751852>] ? sockfd_lookup_light+0x22/0x80
<4>[11340.226897] [<c1753c00>] sys_shutdown+0x30/0x60
<4>[11340.226912] [<c175425c>] sys_socketcall+0x1dc/0x2a0
<4>[11340.226929] [<c149ba78>] ? trace_hardirqs_on_thunk+0xc/0x10
<4>[11340.226944] [<c18860f1>] syscall_call+0x7/0xb
<4>[11340.226960] [<c1880000>] ? restore_cur+0x5e/0xd7
<0>[11340.226969] Code: <f0> ff 4b 08 0f 94 c0 84 c0 74 20 80 7b 19 01 74
2f b8 0a 00 00
Reported-by: Chuansheng Liu <chuansheng.liu@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
If remote device sends l2cap info request before read_remote_ext_feature
completes then mgmt_connected will be sent in hci_acldata_packet() and
remote name request wont be sent and eventually authentication wont happen
Hcidump log of the issue
< HCI Command: Create Connection (0x01|0x0005) plen 13
bdaddr BC:85:1F:74:7F:29 ptype 0xcc18 rswitch 0x01 clkoffset 0x4bf7 (valid)
Packet type: DM1 DM3 DM5 DH1 DH3 DH5
> HCI Event: Command Status (0x0f) plen 4
Create Connection (0x01|0x0005) status 0x00 ncmd 1
> HCI Event: Connect Complete (0x03) plen 11
status 0x00 handle 12 bdaddr BC:85:1F:74:7F:29 type ACL encrypt 0x00
< HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2
handle 12
> HCI Event: Command Status (0x0f) plen 4
Read Remote Supported Features (0x01|0x001b) status 0x00 ncmd 1
> HCI Event: Read Remote Supported Features (0x0b) plen 11
status 0x00 handle 12
Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87
> HCI Event: Max Slots Change (0x1b) plen 3
handle 12 slots 5
< HCI Command: Read Remote Extended Features (0x01|0x001c) plen 3
handle 12 page 1
> HCI Event: Command Status (0x0f) plen 4
Read Remote Extended Features (0x01|0x001c) status 0x00 ncmd 1
> ACL data: handle 12 flags 0x02 dlen 10
L2CAP(s): Info req: type 2
< ACL data: handle 12 flags 0x00 dlen 16
L2CAP(s): Info rsp: type 2 result 0
Extended feature mask 0x00b8
Enhanced Retransmission mode
Streaming mode
FCS Option
Fixed Channels
> HCI Event: Read Remote Extended Features (0x23) plen 13
status 0x00 handle 12 page 1 max 1
Features: 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> ACL data: handle 12 flags 0x02 dlen 10
L2CAP(s): Info req: type 3
< ACL data: handle 12 flags 0x00 dlen 20
L2CAP(s): Info rsp: type 3 result 0
Fixed channel list 0x00000002
L2CAP Signalling Channel
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 2
This patch moves sending mgmt_connected from hci_acldata_packet() to
l2cap_connect_req() since this code is to handle the scenario remote
device sends l2cap connect req too fast
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
The length parameter should be sizeof(req->name) - 1 because there is no
guarantee that string provided by userspace will contain the trailing
'\0'.
Can be easily reproduced by manually setting req->name to 128 non-zero
bytes prior to ioctl(HIDPCONNADD) and checking the device name setup on
input subsystem:
$ cat /sys/devices/pnp0/00\:04/tty/ttyS0/hci0/hci0\:1/input8/name
AAAAAA[...]AAAAAAAAf0:af:f0:af:f0:af
("f0:af:f0:af:f0:af" is the device bluetooth address, taken from "phys"
field in struct hid_device due to overflow.)
Cc: stable@vger.kernel.org
Signed-off-by: Anderson Lizardo <anderson.lizardo@openbossa.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
After sending reset command wait for its command complete event before
sending next command. Some chips sends CC event for command received
before reset if reset was send before chip replied with CC.
This is also required by specification that host shall not send
additional HCI commands before receiving CC for reset.
< HCI Command: Reset (0x03|0x0003) plen 0 [hci0] 18.404612
> HCI Event: Command Complete (0x0e) plen 4 [hci0] 18.405850
Write Extended Inquiry Response (0x03|0x0052) ncmd 1
Status: Success (0x00)
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 [hci0] 18.406079
> HCI Event: Command Complete (0x0e) plen 4 [hci0] 18.407864
Reset (0x03|0x0003) ncmd 1
Status: Success (0x00)
< HCI Command: Read Local Supported Features (0x04|0x0003) plen 0 [hci0] 18.408062
> HCI Event: Command Complete (0x0e) plen 12 [hci0] 18.408835
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Cc: stable@vger.kernel.org
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Use MGMT_STATUS_SUCCESS for success return code.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Those commands don't send any HCI commands to controller so there is no
need to restrict them to only powered up controller. This also makes
implementation more consistent as already stored remote OOB data
persist power toggle.
Signed-off-by: Szymon Janc <szymon.janc@tieto.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Using bit operations solves problems with multiple requests
and clearing state.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Remove code which cannot execute. l2cap_conn_add for AMP_LINK
might only be invoked when receiving data in l2cap_recv_acldata.
But this case is checked in the first statement there.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Use chan->hs_hcon instead of lookup by dst address.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Postpone sending A2MP Create Phylink Response until we got successful
HCI Command Complete after HCI Write Remote AMP Assoc.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
This patch removes unnecessary include of <net/bluetooth/l2cap.h>
in bluetooth/bnep/core.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Signed-off-by: Jorrit Schippers <jorrit@ncode.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID subsystem updates from Jiri Kosina:
1) Support for HID over I2C bus has been added by Benjamin Tissoires.
ACPI device discovery is still in the works.
2) Support for Win8 Multitiouch protocol is being added, most work done
by Benjamin Tissoires as well
3) EIO/ERESTARTSYS is fixed in hiddev/hidraw, fixes by Andrew Duggan
and Jiri Kosina
4) ION iCade driver added by Bastien Nocera
5) Support for a couple new Roccat devices has been added by Stefan
Achatz
6) HID sensor hubs are now auto-detected instead of having to list all
the VID/PID combinations in the blacklist array
7) other random fixes and support for new device IDs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (65 commits)
HID: i2c-hid: add mutex protecting open/close race
Revert "HID: sensors: add to special driver list"
HID: sensors: autodetect USB HID sensor hubs
HID: hidp: fallback to input session properly if hid is blacklisted
HID: i2c-hid: fix ret_count check
HID: i2c-hid: fix i2c_hid_get_raw_report count mismatches
HID: i2c-hid: remove extra .irq field in struct i2c_hid
HID: i2c-hid: reorder allocation/free of buffers
HID: i2c-hid: fix memory corruption due to missing hid declaration
HID: i2c-hid: remove superfluous include
HID: i2c-hid: remove unneeded test in i2c_hid_remove
HID: i2c-hid: i2c_hid_get_report may fail
HID: i2c-hid: also call i2c_hid_free_buffers in i2c_hid_remove
HID: i2c-hid: fix error messages
HID: i2c-hid: fix return paths
HID: i2c-hid: remove unused static declarations
HID: i2c-hid: fix i2c_hid_dbg macro
HID: i2c-hid: fix checkpatch.pl warning
HID: i2c-hid: enhance Kconfig
HID: i2c-hid: change I2C name
...
|
|
'for-3.8/i2c-hid', 'for-3.8/multitouch', 'for-3.8/roccat', 'for-3.8/sensors' and 'for-3.8/upstream' into for-linus
Conflicts:
drivers/hid/hid-core.c
|
|
This patch against kernel 3.7.0-rc8 fixes a kernel oops when turning on the
bluetooth mouse with id 0458:0058 [1].
The mouse in question supports both input and hid sessions, however it is
blacklisted in drivers/hid/hid-core.c so the input session is one that should
be used. Long ago (around kernel 3.0.0) some changes in the bluetooth
subsystem made the kernel do not fallback to input session when hid session is
not supported or blacklisted. This patch restore that behaviour by making the
kernel try the input session if hid_add_device returns ENODEV.
The patch exports hid_ignore() from hid-core.c so that it can be used in the
bluetooth subsystem.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=39882
Signed-off-by: Lamarque V. Souza <lamarque@gmail.com>
Acked-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
|
|
This reverts commit 269c4845d5b3627b95b1934107251bacbe99bb68.
The commit was causing dead locks and NULL dereferences in the sco code:
[28084.104013] BUG: soft lockup - CPU#0 stuck for 22s! [kworker/u:0H:7]
[28084.104021] Modules linked in: btusb bluetooth <snip [last unloaded:
bluetooth]
...
[28084.104021] [<c160246d>] _raw_spin_lock+0xd/0x10
[28084.104021] [<f920e708>] sco_conn_del+0x58/0x1b0 [bluetooth]
[28084.104021] [<f920f1a9>] sco_connect_cfm+0xb9/0x2b0 [bluetooth]
[28084.104021] [<f91ef289>]
hci_sync_conn_complete_evt.isra.94+0x1c9/0x260 [bluetooth]
[28084.104021] [<f91f1a8d>] hci_event_packet+0x74d/0x2b40 [bluetooth]
[28084.104021] [<c1501abd>] ? __kfree_skb+0x3d/0x90
[28084.104021] [<c1501b46>] ? kfree_skb+0x36/0x90
[28084.104021] [<f91fcb4e>] ? hci_send_to_monitor+0x10e/0x190 [bluetooth]
[28084.104021] [<f91fcb4e>] ? hci_send_to_monitor+0x10e/0x190 [bluetooth]
Cc: stable@vger.kernel.org
Reported-by: Chan-yeol Park <chanyeol.park@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Make code more readable by changing CONF_NO_FCS_RECV which is read
as "No L2CAP FCS option received" to CONF_RECV_NO_FCS which means
"Received L2CAP option NO_FCS". This flag really means that we have
received L2CAP FRAME CHECK SEQUENCE (FCS) OPTION with value "No FCS".
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Process L2CAP Config rsp Pending with FCS Option 0x00 (No FCS)
which is sent by Motorola Windows 7 Bluetooth stack. The trace
is shown below (all other options are skipped).
...
< ACL data: handle 1 flags 0x00 dlen 48
L2CAP(s): Config req: dcid 0x0043 flags 0x00 clen 36
...
FCS Option 0x00 (No FCS)
> ACL data: handle 1 flags 0x02 dlen 48
L2CAP(s): Config req: dcid 0x0041 flags 0x00 clen 36
...
FCS Option 0x01 (CRC16 Check)
< ACL data: handle 1 flags 0x00 dlen 47
L2CAP(s): Config rsp: scid 0x0043 flags 0x00 result 4 clen 33
Pending
...
> ACL data: handle 1 flags 0x02 dlen 50
L2CAP(s): Config rsp: scid 0x0041 flags 0x00 result 4 clen 36
Pending
...
FCS Option 0x00 (No FCS)
< ACL data: handle 1 flags 0x00 dlen 14
L2CAP(s): Config rsp: scid 0x0043 flags 0x00 result 0 clen 0
Success
> ACL data: handle 1 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0041 flags 0x00 result 0 clen 0
Success
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
If L2CAP_FEAT_FCS is not supported we sould miss EWS option
configuration because of break. Make code more readable by
combining FCS configuration in the single block.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Before starting quering remote AMP controllers make sure
that there is local active AMP controller.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
After getting HCIDEVDOWN controller did not mark itself as 0x00 which
means: "The Controller radio is available but is currently physically
powered down". The result was even if the hdev was down we return
in controller list value 0x01 "status 0x01 (Bluetooth only)".
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
l2cap_send_disconn_req takes 3 parameters of which conn might be
derived from chan. Make this conversion inside l2cap_send_disconn_req.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Some comparisons needs to double negation(!!) in order to make the value
of the field boolean. Add it to the macro makes the code more readable.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
In order to authenticate and configure an incoming SCO connection, the
BT_DEFER_SETUP option was added. This option is intended to defer reply
to Connect Request on SCO sockets.
When a connection is requested, the listening socket is unblocked but
the effective connection setup happens only on first recv. Any send
between accept and recv fails with -ENOTCONN.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
This option will set the BT_SK_DEFER_SETUP bit in socket flags.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
We need to cancel the hci_power_on work in order to avoid it run when we
try to free the hdev.
[ 1434.201149] ------------[ cut here ]------------
[ 1434.204998] WARNING: at lib/debugobjects.c:261 debug_print_object+0x8e/0xb0()
[ 1434.208324] ODEBUG: free active (active state 0) object type: work_struct hint: hci
_power_on+0x0/0x90
[ 1434.210386] Pid: 8564, comm: trinity-child25 Tainted: G W 3.7.0-rc5-next-
20121112-sasha-00018-g2f4ce0e #127
[ 1434.210760] Call Trace:
[ 1434.210760] [<ffffffff819f3d6e>] ? debug_print_object+0x8e/0xb0
[ 1434.210760] [<ffffffff8110b887>] warn_slowpath_common+0x87/0xb0
[ 1434.210760] [<ffffffff8110b911>] warn_slowpath_fmt+0x41/0x50
[ 1434.210760] [<ffffffff819f3d6e>] debug_print_object+0x8e/0xb0
[ 1434.210760] [<ffffffff8376b750>] ? hci_dev_open+0x310/0x310
[ 1434.210760] [<ffffffff83bf94e5>] ? _raw_spin_unlock_irqrestore+0x55/0xa0
[ 1434.210760] [<ffffffff819f3ee5>] __debug_check_no_obj_freed+0xa5/0x230
[ 1434.210760] [<ffffffff83785db0>] ? bt_host_release+0x10/0x20
[ 1434.210760] [<ffffffff819f4d15>] debug_check_no_obj_freed+0x15/0x20
[ 1434.210760] [<ffffffff8125eee7>] kfree+0x227/0x330
[ 1434.210760] [<ffffffff83785db0>] bt_host_release+0x10/0x20
[ 1434.210760] [<ffffffff81e539e5>] device_release+0x65/0xc0
[ 1434.210760] [<ffffffff819d3975>] kobject_cleanup+0x145/0x190
[ 1434.210760] [<ffffffff819d39cd>] kobject_release+0xd/0x10
[ 1434.210760] [<ffffffff819d33cc>] kobject_put+0x4c/0x60
[ 1434.210760] [<ffffffff81e548b2>] put_device+0x12/0x20
[ 1434.210760] [<ffffffff8376a334>] hci_free_dev+0x24/0x30
[ 1434.210760] [<ffffffff82fd8fe1>] vhci_release+0x31/0x60
[ 1434.210760] [<ffffffff8127be12>] __fput+0x122/0x250
[ 1434.210760] [<ffffffff811cab0d>] ? rcu_user_exit+0x9d/0xd0
[ 1434.210760] [<ffffffff8127bf49>] ____fput+0x9/0x10
[ 1434.210760] [<ffffffff81133402>] task_work_run+0xb2/0xf0
[ 1434.210760] [<ffffffff8106cfa7>] do_notify_resume+0x77/0xa0
[ 1434.210760] [<ffffffff83bfb0ea>] int_signal+0x12/0x17
[ 1434.210760] ---[ end trace a6d57fefbc8a8cc7 ]---
Cc: stable@vger.kernel.org
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
This patch fixes the following report, it happens when accepting rfcomm
connections:
[ 228.165378] =============================================
[ 228.165378] [ INFO: possible recursive locking detected ]
[ 228.165378] 3.7.0-rc1-00536-gc1d5dc4 #120 Tainted: G W
[ 228.165378] ---------------------------------------------
[ 228.165378] bluetoothd/1341 is trying to acquire lock:
[ 228.165378] (sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM){+.+...}, at:
[<ffffffffa0000aa0>] bt_accept_dequeue+0xa0/0x180 [bluetooth]
[ 228.165378]
[ 228.165378] but task is already holding lock:
[ 228.165378] (sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM){+.+...}, at:
[<ffffffffa0205118>] rfcomm_sock_accept+0x58/0x2d0 [rfcomm]
[ 228.165378]
[ 228.165378] other info that might help us debug this:
[ 228.165378] Possible unsafe locking scenario:
[ 228.165378]
[ 228.165378] CPU0
[ 228.165378] ----
[ 228.165378] lock(sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM);
[ 228.165378] lock(sk_lock-AF_BLUETOOTH-BTPROTO_RFCOMM);
[ 228.165378]
[ 228.165378] *** DEADLOCK ***
[ 228.165378]
[ 228.165378] May be due to missing lock nesting notation
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/brcm80211/brcmfmac/wl_cfg80211.c
drivers/net/wireless/iwlwifi/pcie/tx.c
|