| Age | Commit message (Collapse) | Author |
|---|
|
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV6]: Added GSO support for TCPv6
[NET]: Generalise TSO-specific bits from skb_setup_caps
[IPV6]: Added GSO support for TCPv6
[IPV6]: Remove redundant length check on input
[NETFILTER]: SCTP conntrack: fix crash triggered by packet without chunks
[TG3]: Update version and reldate
[TG3]: Add TSO workaround using GSO
[TG3]: Turn on hw fix for ASF problems
[TG3]: Add rx BD workaround
[TG3]: Add tg3_netif_stop() in vlan functions
[TCP]: Reset gso_segs if packet is dodgy
|
|
This patch adds GSO support for IPv6 and TCPv6. This is based on a patch
by Ananda Raju <Ananda.Raju@neterion.com>. His original description is:
This patch enables TSO over IPv6. Currently Linux network stacks
restricts TSO over IPv6 by clearing of the NETIF_F_TSO bit from
"dev->features". This patch will remove this restriction.
This patch will introduce a new flag NETIF_F_TSO6 which will be used
to check whether device supports TSO over IPv6. If device support TSO
over IPv6 then we don't clear of NETIF_F_TSO and which will make the
TCP layer to create TSO packets. Any device supporting TSO over IPv6
will set NETIF_F_TSO6 flag in "dev->features" along with NETIF_F_TSO.
In case when user disables TSO using ethtool, NETIF_F_TSO will get
cleared from "dev->features". So even if we have NETIF_F_TSO6 we don't
get TSO packets created by TCP layer.
SKB_GSO_TCPV4 renamed to SKB_GSO_TCP to make it generic GSO packet.
SKB_GSO_UDPV4 renamed to SKB_GSO_UDP as UFO is not a IPv4 feature.
UFO is supported over IPv6 also
The following table shows there is significant improvement in
throughput with normal frames and CPU usage for both normal and jumbo.
--------------------------------------------------
| | 1500 | 9600 |
| ------------------|-------------------|
| | thru CPU | thru CPU |
--------------------------------------------------
| TSO OFF | 2.00 5.5% id | 5.66 20.0% id |
--------------------------------------------------
| TSO ON | 2.63 78.0 id | 5.67 39.0% id |
--------------------------------------------------
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds GSO support for IPv6 and TCPv6.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't need to check skb->len when we're just about to call
pskb_may_pull since that checks it for us.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
|
|
While debugging a TCP server hang issue, we noticed that currently there is
no way for a user to get the acceptq backlog value for a TCP listen socket.
All the standard networking utilities that display socket info like netstat,
ss and /proc/net/tcp have 2 fields called rx_queue and tx_queue. These
fields do not mean much for listening sockets. This patch uses one of these
unused fields(rx_queue) to export the accept queue len for listening sockets.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch encapsulates the usage of eff_cap (in netlink_skb_params) within
the security framework by extending security_netlink_recv to include a required
capability parameter and converting all direct usage of eff_caps outside
of the lsm modules to use the interface. It also updates the SELinux
implementation of the security_netlink_send and security_netlink_recv
hooks to take advantage of the sid in the netlink_skb_params struct.
This also enables SELinux to perform auditing of netlink capability checks.
Please apply, for 2.6.18 if possible.
Signed-off-by: Darrel Goeddel <dgoeddel@trustedcs.com>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When xt_register_table fails the error is not properly propagated back.
Based on patch by Lepton Wu <ytht.net@gmail.com>.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
locking init cleanups:
- convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK()
- convert rwlocks in a similar manner
this patch was generated automatically.
Motivation:
- cleanliness
- lockdep needs control of lock initialization, which the open-coded
variants do not give
- it's also useful for -rt and for lock debugging in general
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
This patch segments GSO packets received by the IPsec stack. This can
happen when a NIC driver injects GSO packets into the stack which are
then forwarded to another host.
The primary application of this is going to be Xen where its backend
driver may inject GSO packets into dom0.
Of course this also can be used by other virtualisation schemes such as
VMWare or UML since the tap device could be modified to inject GSO packets
received through splice.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Having separate fields in sk_buff for TSO/UFO (tso_size/ufo_size) is not
going to scale if we add any more segmentation methods (e.g., DCCP). So
let's merge them.
They were used to tell the protocol of a packet. This function has been
subsumed by the new gso_type field. This is essentially a set of netdev
feature bits (shifted by 16 bits) that are required to process a specific
skb. As such it's easy to tell whether a given device can process a GSO
skb: you just have to and the gso_type field and the netdev's features
field.
I've made gso_type a conjunction. The idea is that you have a base type
(e.g., SKB_GSO_TCPV4) that can be modified further to support new features.
For example, if we add a hardware TSO type that supports ECN, they would
declare NETIF_F_TSO | NETIF_F_TSO_ECN. All TSO packets with CWR set would
have a gso_type of SKB_GSO_TCPV4 | SKB_GSO_TCPV4_ECN while all other TSO
packets would be SKB_GSO_TCPV4. This means that only the CWR packets need
to be emulated in software.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CONFIG_IPV6_PRIVACY
We need to update hiscore.rule even if we don't enable CONFIG_IPV6_PRIVACY,
because we have more less significant rule; longest match.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two additional labels (RFC 3484, sec. 10.3) for IPv6 addreses
are defined to make a distinction between global unicast
addresses and Unique Local Addresses (fc00::/7, RFC 4193) and
Teredo (2001::/32, RFC 4380). It is necessary to avoid attempts
of connection that would either fail (eg. fec0:: to 2001:feed::)
or be sub-optimal (2001:0:: to 2001:feed::).
Signed-off-by: Łukasz Stelmach <stlman@poczta.fm>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes RTNLGRP_IPV6_IFINFO netlink notifications. Issue
pointed out by Patrick McHardy <kaber@trash.net>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I found a few more spots where pskb_trim_rcsum could be used but were not.
This patch changes them to use it.
Also, sk_filter can get paged skb data. Therefore we must use pskb_trim
instead of skb_trim.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The linearisation operation doesn't need to be super-optimised. So we can
replace __skb_linearize with __pskb_pull_tail which does the same thing but
is more general.
Also, most users of skb_linearize end up testing whether the skb is linear
or not so it helps to make skb_linearize do just that.
Some callers of skb_linearize also use it to copy cloned data, so it's
useful to have a new function skb_linearize_cow to copy the data if it's
either non-linear or cloned.
Last but not least, I've removed the gfp argument since nobody uses it
anymore. If it's ever needed we can easily add it back.
Misc bugs fixed by this patch:
* via-velocity error handling (also, no SG => no frags)
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a secmark field to the skbuff structure, to allow security subsystems to
place security markings on network packets. This is similar to the nfmark
field, except is intended for implementing security policy, rather than than
networking policy.
This patch was already acked in principle by Dave Miller.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
None of the existing helpers expects to get called for related ICMP
packets and some even drop them if they can't parse them.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have xfrm_mode objects we can move the transport mode specific
input decapsulation code into xfrm_mode_transport. This removes duplicate
code as well as unnecessary header movement in case of tunnel mode SAs
since we will discard the original IP header immediately.
This also fixes a minor bug for transport-mode ESP where the IP payload
length is set to the correct value minus the header length (with extension
headers for IPv6).
Of course the other neat thing is that we no longer have to allocate
temporary buffers to hold the IP headers for ESP and IPComp.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the structure xfrm_mode. It is meant to represent
the operations carried out by transport/tunnel modes.
By doing this we allow additional encapsulation modes to be added
without clogging up the xfrm_input/xfrm_output paths.
Candidate modes include 4-to-6 tunnel mode, 6-to-4 tunnel mode, and
BEET modes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The number of locks used to manage afinfo structures can easily be reduced
down to one each for policy and state respectively. This is based on the
observation that the write locks are only held by module insertion/removal
which are very rare events so there is no need to further differentiate
between the insertion of modules like ipv6 versus esp6.
The removal of the read locks in xfrm4_policy.c/xfrm6_policy.c might look
suspicious at first. However, after you realise that nobody ever takes
the corresponding write lock you'll feel better :)
As far as I can gather it's an attempt to guard against the removal of
the corresponding modules. Since neither module can be unloaded at all
we can leave it to whoever fixes up IPv6 unloading :)
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Locks down user pages and sets up for DMA in tcp_recvmsg, then calls
dma_async_try_early_copy in tcp_v4_do_rcv
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In addition to the real on-link routes, NONEXTHOP routes
should be considered on-link.
Problem reported by Meelis Roos <mroos@linux.ee>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Acked-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(CVE-2006-0039)
Solar Designer found a race condition in do_add_counters(). The beginning
of paddc is supposed to be the same as tmp which was sanity-checked
above, but it might not be the same in reality. In case the integer
overflow and/or the race condition are triggered, paddc->num_counters
might not match the allocation size for paddc. If the check below
(t->private->number != paddc->num_counters) nevertheless passes (perhaps
this requires the race condition to be triggered), IPT_ENTRY_ITERATE()
would read kernel memory beyond the allocation size, potentially causing
an oops or leaking sensitive data (e.g., passwords from host system or
from another VPS) via counter increments. This requires CAP_NET_ADMIN.
Signed-off-by: Solar Designer <solar@openwall.com>
Signed-off-by: Kirill Korotaev <dev@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The prefix argument for nf_log_packet is a format specifier,
so don't pass the user defined string directly to it.
Signed-off-by: Philip Craig <philipc@snapgear.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
inet6_csk_xit does not free skb when routing fails.
Signed-off-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We eliminated rt6_dflt_lock (to protect default router pointer)
at 2.6.17-rc1, and introduced rt6_select() for general router selection.
The function is called in the context of rt6_lock read-lock held,
but this means, we have some race conditions when we do round-robin.
Signed-off-by; YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The introduction of x_tables broke comefrom debugging, remove it from
ip6_tables as well (ip_tables already got removed).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- Removed unused argument (nhoff) for ipv6_parse_hopopts().
- Make ipv6_parse_hopopts() to align with other extension header
handlers.
- Removed pointless assignment (hdr), which is not used afterwards.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We did not correctly decode session with preceding extension
header(s). This was because we had already pulled preceding
headers, skb->nh.raw + 40 + 1 - skb->data was minus, and
pskb_may_pull() failed.
We now have IP6CB(skb)->nhoff and skb->h.raw, and we can
start parsing / decoding upper layer protocol from current
position.
Tracked down by Noriaki TAKAMIYA <takamiya@po.ntts.co.jp>
and tested by Kazunori Miyazawa <kazunori@miyazawa.org>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This closes a race where an ipq6hashfn() caller could get a hash value
and race with the cycling of the random seed. By the time they got to
the read_lock they'd have a stale hash value and might not find
previous fragments of their datagram.
This matches the previous patch to IPv4.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
for_each_cpu() actually iterates across all possible CPUs. We've had mistakes
in the past where people were using for_each_cpu() where they should have been
iterating across only online or present CPUs. This is inefficient and
possibly buggy.
We're renaming for_each_cpu() to for_each_possible_cpu() to avoid this in the
future.
This patch replaces for_each_cpu with for_each_possible_cpu under /net
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Deinline a few functions which produce 200+ bytes of code.
Size Uses Wasted Name and definition
===== ==== ====== ================================================
429 3 818 __inet6_lookup include/net/inet6_hashtables.h
404 2 384 __inet6_lookup_established include/net/inet6_hashtables.h
206 3 372 __inet6_hash include/net/inet6_hashtables.h
Signed-off-by: Denis Vlasenko <vda@ilport.com.ua>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Can't build with CONFIG_NETFILTER=y/m on IA64, there's a missing
#include in net/ipv6/netfilter.c
net/ipv6/netfilter.c: In function `nf_ip6_checksum':
net/ipv6/netfilter.c:92: warning: implicit declaration of function
`csum_ipv6_magic'
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Besides removing lots of duplicate code, all converted users benefit
from improved HW checksum error handling. Tested with and without HW
checksums in almost all combinations.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add checksum operation which takes care of verifying the checksum and
dealing with HW checksum errors and avoids multiple checksum
operations by setting ip_summed to CHECKSUM_UNNECESSARY after
successful verification.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the queue rerouter intrastructure to a generic usable
infrastructure for address family specific operations as a base for
some cleanups.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix section mismatch warnings caused by netfilter's init_or_cleanup
functions used in many places by splitting the init from the cleanup
parts.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clean up hook registration by makeing use of the new mass registration and
unregistration helpers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes GRE and SIT to generate port unreachable instead of
protocol unreachable errors when we can't find a matching tunnel for a
packet.
This removes the ambiguity as to whether the error is caused by no
tunnel being found or by the lack of support for the given tunnel
type.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the sending of ICMP messages when there are no IPv4/IPv6
tunnels present to tunnel4/tunnel6 respectively. Please note that for now
if xfrm4_tunnel/xfrm6_tunnel is loaded then no ICMP messages will ever be
sent. This is similar to how we handle AH/ESP/IPCOMP.
This move fixes the bug where we always send an ICMP message when there is
no ip6_tunnel device present for a given packet even if it is later handled
by IPsec. It also causes ICMP messages to be sent when no IPIP tunnel is
present.
I've decided to use the "port unreachable" ICMP message over the current
value of "address unreachable" (and "protocol unreachable" by GRE) because
it is not ambiguous unlike the other ones which can be triggered by other
conditions. There seems to be no standard specifying what value must be
used so this change should be OK. In fact we should change GRE to use
this value as well.
Incidentally, this patch also fixes a fairly serious bug in xfrm6_tunnel
where we don't check whether the embedded IPv6 header is present before
dereferencing it for the inside source address.
This patch is inspired by a previous patch by Hugo Santos <hsantos@av.it.pt>.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This unifies ipt_multiport and ip6t_multiport to xt_multiport.
As a result, this addes support for inversion and port range match
to IPv6 packets.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This unifies ipt_esp and ip6t_esp to xt_esp. Please note that now
a user program needs to specify IPPROTO_ESP as protocol to use esp match
with IPv6. This means that ip6tables requires '-p esp' like iptables.
Signed-off-by: Yasuyuki Kozakai <yasuyuki.kozakai@toshiba.co.jp>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the *_decap_state structures which were previously
used to share state between input/post_input. This is no longer
needed.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the decap_state argument from the xfrm input hook.
Previously this function allowed the input hook to share state with
the post_input hook. The latter has since been removed.
The only purpose for it now is to check the encap type. However, it
is easier and better to move the encap type check to the generic
xfrm_rcv function. This allows us to get rid of the decap state
argument altogether.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
