| Age | Commit message (Collapse) | Author |
|---|
|
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
When a VHT network uses 20 or 40 MHz as per the HT operation
information, the channel center frequency segment 0 field in
the VHT operation information is reserved, so ignore it.
This fixes association with such networks when the AP puts 0
into the field, previously we'd disconnect due to an invalid
channel with the message
wlan0: AP VHT information is invalid, disable VHT
Cc: stable@vger.kernel.org
Fixes: f2d9d270c15ae ("mac80211: support VHT association")
Reported-by: Tim Nelson <tim.l.nelson@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The MLME code in mac80211 must track whether or not the AP changed
bandwidth, but if there's no change while tracking it shouldn't do
anything, otherwise regulatory updates can make it impossible to
connect to certain APs if the regulatory database doesn't match the
information from the AP. See the precise scenario described in the
code.
This still leaves some possible problems with CSA or if the AP
actually changed bandwidth, but those cases are less common and
won't completely prevent using it.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=70881
Cc: stable@vger.kernel.org
Reported-and-tested-by: Nate Carlson <kernel@natecarlson.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
Consider the following (relatively unlikely) scenario:
1) station goes to sleep while frames are buffered in driver
2) driver blocks wakeup (until no more frames are buffered)
3) station wakes up again
4) driver unblocks wakeup
In this case, the current mac80211 code will do the following:
1) WLAN_STA_PS_STA set
2) WLAN_STA_PS_DRIVER set
3) - nothing -
4) WLAN_STA_PS_DRIVER cleared
As a result, no frames will be delivered to the client, even
though it is awake, until it sends another frame to us that
triggers ieee80211_sta_ps_deliver_wakeup() in sta_ps_end().
Since we now take the PS spinlock, we can fix this while at
the same time removing the complexity with the pending skb
queue function. This was broken since my commit 50a9432daeec
("mac80211: fix powersaving clients races") due to removing
the clearing of WLAN_STA_PS_STA in the RX path.
While at it, fix a cleanup path issue when a station is
removed while the driver is still blocking its wakeup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's a race condition in mac80211 because we add stations
to the internal lists after adding them to the driver, which
means that (for example) the following can happen:
1. a station connects and is added
2. first, it is added to the driver
3. then, it is added to the mac80211 lists
If the station goes to sleep between steps 2 and 3, and the
firmware/hardware records it as being asleep, mac80211 will
never instruct the driver to wake it up again as it never
realized it went to sleep since the RX path discarded the
frame as a "spurious class 3 frame", no station entry was
present yet.
Fix this by adding the station in software first, and only
then adding it to the driver. That way, any state that the
driver changes will be reflected properly in mac80211's
station state. The problematic part is the roll-back if the
driver fails to add the station, in that case a bit more is
needed. To not make that overly complex prevent starting BA
sessions in the meantime.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There is a race between the TX path and the STA wakeup: while
a station is sleeping, mac80211 buffers frames until it wakes
up, then the frames are transmitted. However, the RX and TX
path are concurrent, so the packet indicating wakeup can be
processed while a packet is being transmitted.
This can lead to a situation where the buffered frames list
is emptied on the one side, while a frame is being added on
the other side, as the station is still seen as sleeping in
the TX path.
As a result, the newly added frame will not be send anytime
soon. It might be sent much later (and out of order) when the
station goes to sleep and wakes up the next time.
Additionally, it can lead to the crash below.
Fix all this by synchronising both paths with a new lock.
Both path are not fastpath since they handle PS situations.
In a later patch we'll remove the extra skb queue locks to
reduce locking overhead.
BUG: unable to handle kernel
NULL pointer dereference at 000000b0
IP: [<ff6f1791>] ieee80211_report_used_skb+0x11/0x3e0 [mac80211]
*pde = 00000000
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
EIP: 0060:[<ff6f1791>] EFLAGS: 00210282 CPU: 1
EIP is at ieee80211_report_used_skb+0x11/0x3e0 [mac80211]
EAX: e5900da0 EBX: 00000000 ECX: 00000001 EDX: 00000000
ESI: e41d00c0 EDI: e5900da0 EBP: ebe458e4 ESP: ebe458b0
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 8005003b CR2: 000000b0 CR3: 25a78000 CR4: 000407d0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Process iperf (pid: 3934, ti=ebe44000 task=e757c0b0 task.ti=ebe44000)
iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command LQ_CMD (#4e), seq: 0x0903, 92 bytes at 3[3]:9
Stack:
e403b32c ebe458c4 00200002 00200286 e403b338 ebe458cc c10960bb e5900da0
ff76a6ec ebe458d8 00000000 e41d00c0 e5900da0 ebe458f0 ff6f1b75 e403b210
ebe4598c ff723dc1 00000000 ff76a6ec e597c978 e403b758 00000002 00000002
Call Trace:
[<ff6f1b75>] ieee80211_free_txskb+0x15/0x20 [mac80211]
[<ff723dc1>] invoke_tx_handlers+0x1661/0x1780 [mac80211]
[<ff7248a5>] ieee80211_tx+0x75/0x100 [mac80211]
[<ff7249bf>] ieee80211_xmit+0x8f/0xc0 [mac80211]
[<ff72550e>] ieee80211_subif_start_xmit+0x4fe/0xe20 [mac80211]
[<c149ef70>] dev_hard_start_xmit+0x450/0x950
[<c14b9aa9>] sch_direct_xmit+0xa9/0x250
[<c14b9c9b>] __qdisc_run+0x4b/0x150
[<c149f732>] dev_queue_xmit+0x2c2/0xca0
Cc: stable@vger.kernel.org
Reported-by: Yaara Rozenblum <yaara.rozenblum@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
[reword commit log, use a separate lock]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add a new argument for ndo_select_queue() callback that passes a
fallback handler. This gets invoked through netdev_pick_tx();
fallback handler is currently __netdev_pick_tx() as most drivers
invoke this function within their customized implementation in
case for skbs that don't need any special handling. This fallback
handler can then be replaced on other call-sites with different
queue selection methods (e.g. in packet sockets, pktgen etc).
This also has the nice side-effect that __netdev_pick_tx() is
then only invoked from netdev_pick_tx() and export of that
function to modules can be undone.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
|
|
Improves reliability of wifi connections with WPA, since authentication
frames are prioritized over normal traffic and also typically exempt
from aggregation.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case ieee80211_prep_connection() fails to dereference
sdata->vif.chanctx_conf, the function returns and doesn't
free new_sta. fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case we were not suspended, the reconfig function returns without
configuring the scheduled scan.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
During channel context assignment, the interface should
be found by interface iteration, so we need to assign the
pointer before the channel context.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The "new" fragmentation code (since my rewrite almost 5 years ago)
erroneously sets skb->len rather than using skb_trim() to adjust
the length of the first fragment after copying out all the others.
This leaves the skb tail pointer pointing to after where the data
originally ended, and thus causes the encryption MIC to be written
at that point, rather than where it belongs: immediately after the
data.
The impact of this is that if software encryption is done, then
a) encryption doesn't work for the first fragment, the connection
becomes unusable as the first fragment will never be properly
verified at the receiver, the MIC is practically guaranteed to
be wrong
b) we leak up to 8 bytes of plaintext (!) of the packet out into
the air
This is only mitigated by the fact that many devices are capable
of doing encryption in hardware, in which case this can't happen
as the tail pointer is irrelevant in that case. Additionally,
fragmentation is not used very frequently and would normally have
to be configured manually.
Fix this by using skb_trim() properly.
Cc: stable@vger.kernel.org
Fixes: 2de8e0d999b8 ("mac80211: rewrite fragmentation")
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, when a station leaves an IBSS network, the
corresponding BSS is not dropped from cfg80211 if there are
other active stations in the network. But, the small
window that is present when trying to determine a station's
status based on IEEE80211_IBSS_MERGE_INTERVAL introduces
a race.
Instead of trying to keep the BSS, always remove it when
leaving an IBSS network. There is not much benefit to retain
the BSS entry since it will be added with a subsequent join
operation.
This fixes an issue where a dangling BSS entry causes ath9k
to wait for a beacon indefinitely.
Cc: <stable@vger.kernel.org>
Reported-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the driver cannot start the AP or when the assignement
of the beacon goes wrong, we need to unassign the vif.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
sdata->u.ap.request_smps_work can’t be flushed synchronously
under wdev_lock(wdev) since ieee80211_request_smps_ap_work
itself locks the same lock.
While at it, reset the driver_smps_mode when the ap is
stopped to its default: OFF.
This solves:
======================================================
[ INFO: possible circular locking dependency detected ]
3.12.0-ipeer+ #2 Tainted: G O
-------------------------------------------------------
rmmod/2867 is trying to acquire lock:
((&sdata->u.ap.request_smps_work)){+.+...}, at: [<c105b8d0>] flush_work+0x0/0x90
but task is already holding lock:
(&wdev->mtx){+.+.+.}, at: [<f9b32626>] cfg80211_stop_ap+0x26/0x230 [cfg80211]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&wdev->mtx){+.+.+.}:
[<c10aefa9>] lock_acquire+0x79/0xe0
[<c1607a1a>] mutex_lock_nested+0x4a/0x360
[<fb06288b>] ieee80211_request_smps_ap_work+0x2b/0x50 [mac80211]
[<c105cdd8>] process_one_work+0x198/0x450
[<c105d469>] worker_thread+0xf9/0x320
[<c10669ff>] kthread+0x9f/0xb0
[<c1613397>] ret_from_kernel_thread+0x1b/0x28
-> #0 ((&sdata->u.ap.request_smps_work)){+.+...}:
[<c10ae9df>] __lock_acquire+0x183f/0x1910
[<c10aefa9>] lock_acquire+0x79/0xe0
[<c105b917>] flush_work+0x47/0x90
[<c105d867>] __cancel_work_timer+0x67/0xe0
[<c105d90f>] cancel_work_sync+0xf/0x20
[<fb0765cc>] ieee80211_stop_ap+0x8c/0x340 [mac80211]
[<f9b3268c>] cfg80211_stop_ap+0x8c/0x230 [cfg80211]
[<f9b0d8f9>] cfg80211_leave+0x79/0x100 [cfg80211]
[<f9b0da72>] cfg80211_netdev_notifier_call+0xf2/0x4f0 [cfg80211]
[<c160f2c9>] notifier_call_chain+0x59/0x130
[<c106c6de>] __raw_notifier_call_chain+0x1e/0x30
[<c106c70f>] raw_notifier_call_chain+0x1f/0x30
[<c14f8213>] call_netdevice_notifiers_info+0x33/0x70
[<c14f8263>] call_netdevice_notifiers+0x13/0x20
[<c14f82a4>] __dev_close_many+0x34/0xb0
[<c14f83fe>] dev_close_many+0x6e/0xc0
[<c14f9c77>] rollback_registered_many+0xa7/0x1f0
[<c14f9dd4>] unregister_netdevice_many+0x14/0x60
[<fb06f4d9>] ieee80211_remove_interfaces+0xe9/0x170 [mac80211]
[<fb055116>] ieee80211_unregister_hw+0x56/0x110 [mac80211]
[<fa3e9396>] iwl_op_mode_mvm_stop+0x26/0xe0 [iwlmvm]
[<f9b9d8ca>] _iwl_op_mode_stop+0x3a/0x70 [iwlwifi]
[<f9b9d96f>] iwl_opmode_deregister+0x6f/0x90 [iwlwifi]
[<fa405179>] __exit_compat+0xd/0x19 [iwlmvm]
[<c10b8bf9>] SyS_delete_module+0x179/0x2b0
[<c1613421>] sysenter_do_call+0x12/0x32
Fixes: 687da132234f ("mac80211: implement SMPS for AP")
Cc: <stable@vger.kernel.org> [3.13]
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
ieee80211_start_roc_work() might add a new roc
to existing roc, and tell cfg80211 it has already
started.
However, this might happen before the roc cookie
was set, resulting in REMAIN_ON_CHANNEL (started)
event with null cookie. Consequently, it can make
wpa_supplicant go out of sync.
Fix it by setting the roc cookie earlier.
Cc: stable@vger.kernel.org
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This capabilities weren't propagated to the radiotap header.
We don't set here the VHT_KNOWN / MCS_HAVE flag because not
all the low level drivers will know how to properly flag
the frames, hence the low level driver will be in charge
of setting IEEE80211_RADIOTAP_MCS_HAVE_FEC,
IEEE80211_RADIOTAP_MCS_HAVE_STBC and / or
IEEE80211_RADIOTAP_VHT_KNOWN_STBC according to its
capabilities.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
ieee80211_rx_status.flags is full. Define a new vht_flag
variable to be able to set more VHT related flags and make
room in flags.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath10k]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The purpose of this housekeeping is to make some room for
VHT flags. The radiotap vendor fields weren't in use.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In association request frames, there may be IEs passed from
userspace (such as interworking IEs) between HT and VHT, so
add code to insert those inbetween them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In probe request frames, the VHT IEs should come before any
vendor IEs, but after interworking and similar, so add code
to order them correctly wrt. the IEs passed from userspace.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Update the operating mode field is needed when an association
request contains the operating mode notification element and
it's not just changed later on the fly.
Signed-off-by: Marek Kwaczynski <marek.kwaczynski@tieto.com>
[clarify commit log, comments & fix whitespace]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When receiving an IBSS_JOINED event select the BSS object
based on the {bssid, channel} couple rather than the bssid
only.
With the current approach if another cell having the same
BSSID (but using a different channel) exists then cfg80211
picks up the wrong BSS object.
The result is a mismatching channel configuration between
cfg80211 and the driver, that can lead to any sort of
problem.
The issue can be triggered by having an IBSS sitting on
given channel and then asking the driver to create a new
cell using the same BSSID but with a different frequency.
By passing the channel to cfg80211_get_bss() we can solve
this ambiguity and retrieve/create the correct BSS object.
All the users of cfg80211_ibss_joined() have been changed
accordingly.
Moreover WARN when cfg80211_ibss_joined() gets a NULL
channel as argument and remove a bogus call of the same
function in ath6kl (it does not make sense to call
cfg80211_ibss_joined() with a zero BSSID on ibss-leave).
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Bing Zhao <bzhao@marvell.com>
Cc: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Cc: libertas-dev@lists.infradead.org
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
[minor code cleanup in ath6kl]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Action, disassoc and deauth frames are bufferable, and as such don't
have the PM bit in the frame control field reserved which means we
need to react to the bit when receiving in such a frame.
Fix this by introducing a new helper ieee80211_is_bufferable_mmpdu()
and using it for the RX path that currently ignores the PM bit in
any non-data frames for doze->wake transitions, but listens to it in
all frames for wake->doze transitions, both of which are wrong.
Also use the new helper in the TX path to clean up the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Compiling with W=1 found a few variables that are set
but not used (-Wunused-but-set-variable), remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Responding to probe requests for scanning clients will often create
excessive retries, as it happens quite often that the scanning client
already left the channel. Therefore do it like hostapd and send probe
responses for wildcard SSID only once by using the noack flag.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
[fix typo & 'wildcard SSID' in commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The ieee80211_vif_use_channel() function calls
ieee80211_vif_release_channel(), so there's no need to call it
explicitly in __ieee80211_sta_join_ibss().
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The patch adds a missing sdata lock and adds a few
lockdeps for easier maintenance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
radar_required setting wasn't protected by
local->mtx in some places. This should prevent
from scanning/radar detection/roc colliding.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The sdata->vif.csa_active could be left set after,
e.g. channel context constraints check fail in STA
mode leaving the interface in a strange state for
a brief period of time until it is disconnected.
This was harmless but ugly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If CSA for AP interface failed and the interface
was not stopped afterwards another CSA request
would leak sdata->u.ap.next_beacon.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of having
ieee80211_bss_info_change_notify() scattered all
over the place just call it once when finalizing
CSA.
As a side effect this patch adds missing error
checking for IBSS CSA beacon update.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
[fix err vs. changed variable usage in ieee80211_csa_finalize()]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A few places weren't checking that the frame passed to the
function actually has enough data even though the function
clearly documents it must have a payload byte. Make this
safer by changing the function to take an skb and checking
the length inside. The old version is preserved for now as
the rtl* drivers use it and don't have a correct skb.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
ATM, {ADD,DEL}BA and BAR frames are sent on the AC matching the TID of
the BA parameters. In the discussion [1] about this patch, Johannes
recalled that it fixed some races with the DELBA and indeed this
behavior was introduced in [2].
While [2] is right for the BARs, the part queueing the {ADD,DEL}BAs on
their BA params TID AC violates the spec and is more a workaround for
some drivers. Helmut expressed some concerns wrt such drivers, in
particular DELBAs in rt2x00.
ATM, DELBAs are sent after a driver has called (hence "purposely")
ieee80211_start_tx_ba_cb_irqsafe and Johannes and Emmanuel gave some
details wrt intentions behind the split of the IEEE80211_AMPDU_TX_STOP_*
given to the driver ampdu_action supposed to call this function, which
could prove handy to people trying to do the right thing in faulty
drivers (if their fw/hw don't get in their way).
[1] http://mid.gmane.org/1390391564-18481-1-git-send-email-karl.beldan@gmail.com
[2] Commit: cf6bb79ad828 ("mac80211: Use appropriate TID for sending BAR, ADDBA and DELBA frames")
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's not a single rate control algorithm actually in
a separate module where the module refcount would be
required. Similarly, there's no specific rate control
module.
Therefore, all the module handling code in rate control
is really just dead code, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The sample table is initialized only once at module start, so
is really __read_mostly. Additionally, the code to init it can
be marked __init since it will never be needed again, it is
likely automatically inlined into the __init function already
by the compiler, so this doesn't really make a difference.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The wiphy privid (to identify wiphys) and the cfg80211
ops should both be const, so change them to be.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Change the code to allow making all the rate control ops
const, nothing ever needs to change them. Also change all
drivers to make use of this and mark the ops const.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Restrict our published beamformee STS capability according
to the AP value.
Some AP show bad behaviour in interoperability testing
when our capabilities are better.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Initialize the buffer to all zeroes, otherwise the stack
data might be interpreted as the TID, which is likely to
fail completely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case the given ROC duration is 0, update it to a minimal value before
setting the ieee80211_roc_work parameters, so it also would be valid
for cases where scan is in progress or there are other ROCs queued.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since we copy the mesh_id_len into our own data structures,
use it consistently and don't sometimes use cfg80211's copy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The mesh_id is an array so can't ever be NULL, it looks
like mesh_id_len check was intended instead. However,
since the previous patch, cfg80211 does the check, so
just remove it here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The mesh precedence value in ieee80211_channel_switch
should be incremented or set to 1 only if this is the
initiator of mesh channel switch. For non-initiator,
the precedence value has updated using the Mesh
Channel Switch Parameters element. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When IEEE80211_HW_SIGNAL_UNSPEC is set, mac80211 will perform a
division by max_signal in ieee80211_bss_info_update. If max_signal
is not properly set by the driver (for example it is zero) this
leads to a divide error and crash.
Thanks to Larry Finger, who pointed me to this.
This patch adds in ieee80211_register_hw one more check to detect
this condition and eventually returns -EINVAL, as already done for
other checks already performed there.
Signed-off-by: andrea merello <andrea.merello@gmail.com>
[move to an already existing SIGNAL_UNSPEC check]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Commit 7ec7c4a9a686 ("mac80211: port CCMP to cryptoapi's CCM driver")
resulted in the 'encrypted' param of ccmp_special_blocks() to be no
longer used so it can be dropped from the prototype.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
