| Age | Commit message (Collapse) | Author |
|---|
|
Until now, a u16 value was used to represent bitrate value.
With VHT bitrates this becomes too small.
Introduce a new 32-bit bitrate attribute. nl80211 will report
both the new and the old attribute, unless the bitrate doesn't
fit into the old u16 attribute in which case only the new one
will be reported.
User space tools encouraged to prefer the 32-bit attribute, if
available (since it won't be available on older kernels.)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[reword commit message and comments a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Michal's monitor channel tracking introduce a locking problem
as it locked the rdev lock inside the netdev notifier which
isn't allowed as we might already hold it if we get there by
removing an interface that is up.
Fix this by relying only on the RTNL to protect the interface
counters, the RTNL is always held in these code paths anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add regulatory rule for the 60g band
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add enumerations for both cfg80211 and nl80211.
This expands wiphy.bands etc. arrays.
Extend channel <-> frequency translation to cover 60g band
and modify the rate check logic since there are no legacy
mandatory rates (only MCS is used.)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
devlist_mtx locking is changed to accomodate changes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
.connect cannot be handled since the driver scans
and connects on its own. It is up to the driver
then to refuse a connection (with -EBUSY for
example).
Non-fixed channel IBSSes always take a single
channel resource. For example two non-fixed
channel IBSSes always take up 2
num_different_channels, even if they operate on
the same channel at a given point of time.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We do not need it anymore since cfg80211 tracks
monitor channel and monitor channel type.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Implements behaviour seen in mac80211. A running
monitor always has a channel - even before
.set_channel. This way we won't break current
behaviour.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make it even more obvious we support single
monitor channel. This will allow us to remove
.get_channel.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Having .set_monitor_channel work with non-monitor
interfaces running would make interface
combinations accounting ambiguous.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Implements .set_monitor_enabled(wiphy, enabled).
Notifies driver upon change of interface layout.
If only monitor interfaces become present it is
called with 2nd argument being true. If
non-monitor interface appears then 2nd argument
is false. Driver is notified only upon change.
This makes it more obvious about the fact that
cfg80211 supports single monitor channel. Once we
implement multi-channel we don't want to allow
setting monitor channel while other interface
types are running. Otherwise it would be ambiguous
once we start considering num_different_channels.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Helper function for finding out which channel is
used by a given interface.
An exclusive channel can be used only by a single
interface. This is mainly for non-fixed channel
IBSS handling.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
IBSS may hop between channels. It is necessary to
account this special case when considering
interface combinations.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We need to know which channel is used by a running
AP and mesh for channel context accounting and
finding matching/active interface combination.
STA/IBSS have current_bss already which allows us
to check which channel a vif is tuned to.
Non-fixed channel IBSS can be handled with
additional changes.
Monitor mode is going to be handled differently.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We'll need this for proper channel tracking (which
is going to be needed for channel context
accounting and finding matching/active interface
combination).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This functionality will be reused when interface
is going down. Avoids code duplication. Also adds
missing wdev locking.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
Allow drivers to advertise their VHT capabilities
and export them to userspace via nl80211.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When CONFIG_PM is disabled, no device can possibly
support WoWLAN since it can't go to sleep to start
with. Due to this, mac80211 had even rejected the
hardware registration. By making all the code and
data for WoWLAN depend on CONFIG_PM we can promote
this runtime error to a compile-time error.
Add #ifdef around all WoWLAN code to remove it in
systems that don't need it as they never suspend.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
Support configuring an RSSI threshold in dBm (s32) when requesting
scheduled scan, below which a BSS won't be reported by the cfg80211
driver.
Signed-off-by: Thomas Pedersen <c_tpeder@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
Commit "cfg80211: provide channel to start_ap function" assumes that the
channel is always passed to the NL80211_CMD_START_AP command, however
in case of multi-BSSID, hostapd only passes the channel for the first vif.
This makes starting beaconing on secondary vifs fail with -EINVAL.
Fix this by storing the channel provided to .start_ap in wdev->preset_chan
and picking the first AP vif's channel for secondary vifs if not provided.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To fix the testmode cross-namespace access problem,
use __cfg80211_rdev_from_attrs() to get the device
instead of open-coding similar functionality.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Change the function to __cfg80211_rdev_from_attrs
to take attributes instead of the info struct to
make it usable from dump callbacks for testmode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are currently a few ways to "escape"
the network namespace and access a wiphy
that belongs to another namespace. Add a
netns argument to the relevant functions
to fix this.
One remaining issue with testmode will be
fixed in a follow-up patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Refactor the function to make it easier to
extend.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some of the functions to retrieve a device can
be static as they're used only in nl80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As defined in section 13.10.9.3 Case D (802.11-2012), this
control variable is used to limit the mesh STA to send only
one PREQ to a root mesh STA within this interval of time
(in TUs). The default value for this variable is set to
2000 TUs. However, for current implementation, the maximum
configurable of dot11MeshHWMPconfirmationInterval is
restricted by dot11MeshHWMPactivePathTimeout.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
dot11MeshHWMPactivePathToRootTimeout
Add the mesh configuration parameters dot11MeshHWMProotInterval
and dot11MeshHWMPactivePathToRootTimeout to be used by
proactive PREQ mechanism.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/ath/ath9k/main.c
net/bluetooth/hci_event.c
|
|
It should be NL80211_SCHED_SCAN_MATCH_ATTR_SSID as
documented, not NL80211_ATTR_SCHED_SCAN_MATCH_SSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
reg_timeout_work() calls restore_regulatory_settings() which
takes cfg80211_mutex.
reg_set_request_processed() already holds cfg80211_mutex
before calling cancel_delayed_work_sync(reg_timeout),
so it might deadlock.
Call the async cancel_delayed_work instead, in order
to avoid the potential deadlock.
This is the relevant lockdep warning:
cfg80211: Calling CRDA for country: XX
======================================================
[ INFO: possible circular locking dependency detected ]
3.4.0-rc5-wl+ #26 Not tainted
-------------------------------------------------------
kworker/0:2/1391 is trying to acquire lock:
(cfg80211_mutex){+.+.+.}, at: [<bf28ae00>] restore_regulatory_settings+0x34/0x418 [cfg80211]
but task is already holding lock:
((reg_timeout).work){+.+...}, at: [<c0059e94>] process_one_work+0x1f0/0x480
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 ((reg_timeout).work){+.+...}:
[<c008fd44>] validate_chain+0xb94/0x10f0
[<c0090b68>] __lock_acquire+0x8c8/0x9b0
[<c0090d40>] lock_acquire+0xf0/0x114
[<c005b600>] wait_on_work+0x4c/0x154
[<c005c000>] __cancel_work_timer+0xd4/0x11c
[<c005c064>] cancel_delayed_work_sync+0x1c/0x20
[<bf28b274>] reg_set_request_processed+0x50/0x78 [cfg80211]
[<bf28bd84>] set_regdom+0x550/0x600 [cfg80211]
[<bf294cd8>] nl80211_set_reg+0x218/0x258 [cfg80211]
[<c03c7738>] genl_rcv_msg+0x1a8/0x1e8
[<c03c6a00>] netlink_rcv_skb+0x5c/0xc0
[<c03c7584>] genl_rcv+0x28/0x34
[<c03c6720>] netlink_unicast+0x15c/0x228
[<c03c6c7c>] netlink_sendmsg+0x218/0x298
[<c03933c8>] sock_sendmsg+0xa4/0xc0
[<c039406c>] __sys_sendmsg+0x1e4/0x268
[<c0394228>] sys_sendmsg+0x4c/0x70
[<c0013840>] ret_fast_syscall+0x0/0x3c
-> #1 (reg_mutex){+.+.+.}:
[<c008fd44>] validate_chain+0xb94/0x10f0
[<c0090b68>] __lock_acquire+0x8c8/0x9b0
[<c0090d40>] lock_acquire+0xf0/0x114
[<c04734dc>] mutex_lock_nested+0x48/0x320
[<bf28b2cc>] reg_todo+0x30/0x538 [cfg80211]
[<c0059f44>] process_one_work+0x2a0/0x480
[<c005a4b4>] worker_thread+0x1bc/0x2bc
[<c0061148>] kthread+0x98/0xa4
[<c0014af4>] kernel_thread_exit+0x0/0x8
-> #0 (cfg80211_mutex){+.+.+.}:
[<c008ed58>] print_circular_bug+0x68/0x2cc
[<c008fb28>] validate_chain+0x978/0x10f0
[<c0090b68>] __lock_acquire+0x8c8/0x9b0
[<c0090d40>] lock_acquire+0xf0/0x114
[<c04734dc>] mutex_lock_nested+0x48/0x320
[<bf28ae00>] restore_regulatory_settings+0x34/0x418 [cfg80211]
[<bf28b200>] reg_timeout_work+0x1c/0x20 [cfg80211]
[<c0059f44>] process_one_work+0x2a0/0x480
[<c005a4b4>] worker_thread+0x1bc/0x2bc
[<c0061148>] kthread+0x98/0xa4
[<c0014af4>] kernel_thread_exit+0x0/0x8
other info that might help us debug this:
Chain exists of:
cfg80211_mutex --> reg_mutex --> (reg_timeout).work
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock((reg_timeout).work);
lock(reg_mutex);
lock((reg_timeout).work);
lock(cfg80211_mutex);
*** DEADLOCK ***
2 locks held by kworker/0:2/1391:
#0: (events){.+.+.+}, at: [<c0059e94>] process_one_work+0x1f0/0x480
#1: ((reg_timeout).work){+.+...}, at: [<c0059e94>] process_one_work+0x1f0/0x480
stack backtrace:
[<c001b928>] (unwind_backtrace+0x0/0x12c) from [<c0471d3c>] (dump_stack+0x20/0x24)
[<c0471d3c>] (dump_stack+0x20/0x24) from [<c008ef70>] (print_circular_bug+0x280/0x2cc)
[<c008ef70>] (print_circular_bug+0x280/0x2cc) from [<c008fb28>] (validate_chain+0x978/0x10f0)
[<c008fb28>] (validate_chain+0x978/0x10f0) from [<c0090b68>] (__lock_acquire+0x8c8/0x9b0)
[<c0090b68>] (__lock_acquire+0x8c8/0x9b0) from [<c0090d40>] (lock_acquire+0xf0/0x114)
[<c0090d40>] (lock_acquire+0xf0/0x114) from [<c04734dc>] (mutex_lock_nested+0x48/0x320)
[<c04734dc>] (mutex_lock_nested+0x48/0x320) from [<bf28ae00>] (restore_regulatory_settings+0x34/0x418 [cfg80211])
[<bf28ae00>] (restore_regulatory_settings+0x34/0x418 [cfg80211]) from [<bf28b200>] (reg_timeout_work+0x1c/0x20 [cfg80211])
[<bf28b200>] (reg_timeout_work+0x1c/0x20 [cfg80211]) from [<c0059f44>] (process_one_work+0x2a0/0x480)
[<c0059f44>] (process_one_work+0x2a0/0x480) from [<c005a4b4>] (worker_thread+0x1bc/0x2bc)
[<c005a4b4>] (worker_thread+0x1bc/0x2bc) from [<c0061148>] (kthread+0x98/0xa4)
[<c0061148>] (kthread+0x98/0xa4) from [<c0014af4>] (kernel_thread_exit+0x0/0x8)
cfg80211: Calling CRDA to update world regulatory domain
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
Cc: stable@kernel.org
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
fix the coding style related to mesh parameters, especially the indentation,
as pointed out by Johannes Berg.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Don't validate interface combinations on a stopped
interface. Otherwise we might end up being able to
create a new interface with a certain type, but
won't be able to change an existing interface
into that type.
This also skips some other functions when
interface is stopped and changing interface type.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The remain-on-channel time validation shouldn't
depend on the value of HZ, as it does now with
the check against jiffies, since then you might
use a value that works on one system but not on
another. Fix it by checking against a minimum
that's fixed.
Also add validation of the wait duration for a
management frame TX since this also translates
into remain-on-channel internally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().
Also describe the desired set_monitor_channel()
semantics more clearly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
Conflicts:
drivers/net/wireless/iwlwifi/iwl-drv.c
|
|
Just like the AP mode patch, instead of setting
the channel and then joining the mesh network,
provide the channel to join the network on to
the join_mesh() function.
Like in AP mode, you can also give the channel
to the join-mesh nl80211 command now.
Unlike AP mode, it picks a default channel if
none was given.
As libertas uses mesh mode interfaces but has
no join_mesh callback and we can't simply break
it, keep some compatibility code for that case
and configure the channel directly for it.
In the non-libertas case, where we store the
channel until join, allow setting it while the
interface is down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If it worked (Felix says it doesn't right now), the
typical use-case for WDS interfaces would be to be
slaved to AP mode interfaces. Therefore, it isn't
necessary to set the channel on WDS interfaces. As
they don't support powersave or anything like that,
they also couldn't use a different channel anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of setting the channel first and then
starting the AP, let cfg80211 store the channel
and provide it as one of the AP settings.
This means that now you have to set the channel
before you can start an AP interface, but since
hostapd/wpa_supplicant always do that we're OK
with this change.
Alternatively, it's now possible to give the
channel as an attribute to the start-ap nl80211
command, overriding any preset channel.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Change cfg80211_can_beacon_sec_chan() to return true
if there is no secondary channel to simplify all the
current users of it. They all check the channel type
before calling the function because it returns false
if there's no secondary channel.
Also actually document the return value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Almost all wireless tools have transitioned to
or at least added compatibility with nl80211 so
there's no real need for CONFIG_CFG80211_WEXT
any more. Mark it for removal, and also change
the default to not be enabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The only user of this was hal prior to its 0.5.12
release which happened over two years ago, so I'm
sure this can be removed without issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If a given interface combination doesn't contain
a required interface type then we missed checking
that and erroneously allowed it even though iface
type wasn't there at all. Add a check that makes
sure that all interface types are accounted for.
Cc: stable@kernel.org
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
CFG80211_DEV_WARN_ON() at "net/wireless/ibss.c line 63"
is unnecessarily triggered even after successful connection,
when cfg80211_ibss_joined() is called by driver inside
.join_ibss handler.
This patch fixes the problem by changing 'sme_state' in ibss path
and having WARN_ON() check for 'sme_state' similar to infra
association.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
|
|
There are four instances in nl80211 of getting the
channel type from the attribute and validating it,
refactor those.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
It should return bool, not int. The function even
does return true/false.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We don't really want/need to maintain the old
station flags API any more, so refuse changes
to new (not yet defined) flags from the old
flags API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
