| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
|
|
Last part of hop-limit determination is always:
hoplimit = dst_metric(dst, RTAX_HOPLIMIT);
if (hoplimit < 0)
hoplimit = ipv6_get_hoplimit(dst->dev).
Let's consolidate it as ip6_dst_hoplimit(dst).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
|
|
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
|
|
old:
| text data bss dec hex filename
| 28599 1416 96 30111 759f net/ipv6/addrconf.o
new:
| text data bss dec hex filename
| 28007 1416 96 29519 734f net/ipv6/addrconf.o
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
|
|
Each MIPv6 XFRM state (DSTOPT/RH2) holds either destination or source
address to be mangled in the IPv6 header (that is "CoA").
On Inter-MN communication after both nodes binds each other,
they use route optimized traffic two MIPv6 states applied, and
both source and destination address in the IPv6 header
are replaced by the states respectively.
The packet format is correct, however, next-hop routing search
are not.
This patch fixes it by remembering address pairs for later states.
Based on patch from Masahide NAKAMURA <nakam@linux-ipv6.org>.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
|
|
| % size old/net/ipv6/xfrm6_tunnel.o new/net/ipv6/xfrm6_tunnel.o
| text data bss dec hex filename
| 1606 40 2080 3726 e8e old/net/ipv6/xfrm6_tunnel.o
| 1574 40 2080 3694 e6e new/net/ipv6/xfrm6_tunnel.o
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
|
|
| % size old/net/ipv6/xfrm6_input.o new/net/ipv6/xfrm6_input.o
| text data bss dec hex filename
| 1026 0 0 1026 402 old/net/ipv6/xfrm6_input.o
| 947 0 0 947 3b3 new/net/ipv6/xfrm6_input.o
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
|
|
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
|
|
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow to create sockets in the namespace if the protocol ok with this.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IP layer now can handle multiple namespaces normally. So, process such
packets normally and drop them only if the transport layer is not
aware about namespaces.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were no packets in the namespace other than initial
previously. This will be changed in the neareast future. Netfilters
are not namespace aware and should be processed in the initial
namespace only for now.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace all the reast of the init_net with a proper net on the socket
layer.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace all the rest of the init_net with a proper net on the IP layer.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass the init_net there for now.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass the init_net there for now.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip_options_compile uses inet_addr_type which requires a namespace. The
packet argument is optional, so parameter is the only way to obtain
it. Pass the init_net there for now.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Seqfile operation showing /proc/net/arp are already namespace
aware. All we need is to register this file for each namespace.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Get namespace from a device and pass it to the routing engine. Enable
ARP packet processing and device notifiers after that.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This file displays the registered packet types, but some of them
(packet sockets creates such) can be bound to a net device and showing
them in a wrong namespace is not correct.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
UDP-Lite sockets are displayed in another files, rather than
UDP ones, so make the present in namespaces as well.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just introduce a helper to remove ifdefs from inside the
udplite4_register function. This will help to make the next patch
nicer.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the commit f40c8174d3c21bf178283f3ef3aa8c7bf238fdec ([NETNS][IPV4]
tcp - make proc handle the network namespaces) it is now possible to make
this file present in newly created namespaces.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the commit a91275eff43a527e1a25d6d034cbcd19ee323e64 ([NETNS][IPV6]
udp - make proc handle the network namespace) it is now possible to make
this file present in newly created namespaces.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
net/ipv6/ndisc.c
|
|
sctp_datamsg_free and sctp_datamsg_track are just aliases for
sctp_datamsg_put and sctp_chunk_hold, respectively.
Saves 32 Bytes on x86.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
133886 2004 220 136110 213ae sctp.new/sctp.o
134018 2004 220 136242 21432 sctp.old/sctp.o
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make /proc/net/fib_trie and /proc/net/fib_triestat display
all routing tables, not just local and main.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Olsa <olsajiri@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the first u32 copied from syncookie_secret is overwritten by the
minute-counter four lines below. After adjusting the destination
address, the size of syncookie_secret can be reduced accordingly.
AFAICS, the only other user of syncookie_secret[] is the ipv6
syncookie support. Because ipv6 syncookies only grab 44 bytes from
syncookie_secret[], this shouldn't affect them in any way.
With fixes from Glenn Griffin.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Glenn Griffin <ggriffin.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HTB is event driven algorithm and part of its work is to apply
scheduled events at proper times. It tried to defend itself from
livelock by processing only limited number of events per dequeue.
Because of faster computers some users already hit this hardcoded
limit.
This patch limits processing up to 2 jiffies (why not 1 jiffie ?
because it might stop prematurely when only fraction of jiffie
remains).
Signed-off-by: Martin Devera <devik@cdi.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patches removes unused code in ndisc_send_redirect() method in
net/ipv6/ndisc.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable cb is initialized but never used otherwise.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier i;
constant C;
@@
(
extern T i;
|
- T i;
<+... when != i
- i = C;
...+>
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable hlen is initialized but never used otherwise.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier i;
constant C;
@@
(
extern T i;
|
- T i;
<+... when != i
- i = C;
...+>
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This gets rid of a warning caused by the test in rcu_assign_pointer.
I tried to fix rcu_assign_pointer, but that devolved into a long set
of discussions about doing it right that came to no real solution.
Since the test in rcu_assign_pointer for constant NULL would never
succeed in fib_trie, just open code instead.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The route table parameters are set based on system memory and sysctl
values that almost never change. Also the genid only changes every
10 minutes.
RTprint is defined by never used.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just remove it.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sorry for the patch sequence confusion :| but I found that the similar
thing can be done for raw sockets easily too late.
Expand the proto.h union with the raw_hashinfo member and use it in
raw_prot and rawv6_prot. This allows to drop the protocol specific
versions of hash and unhash callbacks.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After this we have only udp_lib_get_port to get the port and two
stubs for ipv4 and ipv6. No difference in udp and udplite except
for initialized h.udp_hash member.
I tried to find a graceful way to drop the only difference between
udp_v4_get_port and udp_v6_get_port (i.e. the rcv_saddr comparison
routine), but adding one more callback on the struct proto didn't
appear such :( Maybe later.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Inspired by the commit ab1e0a13 ([SOCK] proto: Add hashinfo member to
struct proto) from Arnaldo, I made similar thing for UDP/-Lite IPv4
and -v6 protocols.
The result is not that exciting, but it removes some levels of
indirection in udpxxx_get_port and saves some space in code and text.
The first step is to union existing hashinfo and new udp_hash on the
struct proto and give a name to this union, since future initialization
of tcpxxx_prot, dccp_vx_protinfo and udpxxx_protinfo will cause gcc
warning about inability to initialize anonymous member this way.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes code a bit more uniform and straigthforward.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip_options->is_data is assigned only and never checked. The structure is
not a part of kernel interface to the userspace. So, it is safe to remove
this field.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is the only way to reach ip_options compile with opt != NULL:
ip_options_get_finish
opt->is_data = 1;
ip_options_compile(opt, NULL)
So, checking for is_data inside opt != NULL branch is not needed.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While testing the virtio-net driver on KVM with TSO I noticed
that TSO performance with a 1500 MTU is significantly worse
compared to the performance of non-TSO with a 16436 MTU. The
packet dump shows that most of the packets sent are smaller
than a page.
Looking at the code this actually is quite obvious as it always
stop extending the packet if it's the first packet yet to be
sent and if it's larger than the MSS. Since each extension is
bound by the page size, this means that (given a 1500 MTU) we're
very unlikely to construct packets greater than a page, provided
that the receiver and the path is fast enough so that packets can
always be sent immediately.
The fix is also quite obvious. The push calls inside the loop
is just an optimisation so that we don't end up doing all the
sending at the end of the loop. Therefore there is no specific
reason why it has to do so at MSS boundaries. For TSO, the
most natural extension of this optimisation is to do the pushing
once the skb exceeds the TSO size goal.
This is what the patch does and testing with KVM shows that the
TSO performance with a 1500 MTU easily surpasses that of a 16436
MTU and indeed the packet sizes sent are generally larger than
16436.
I don't see any obvious downsides for slower peers or connections,
but it would be prudent to test this extensively to ensure that
those cases don't regress.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change TCP_DEFER_ACCEPT implementation so that it transitions a
connection to ESTABLISHED after handshake is complete instead of
leaving it in SYN-RECV until some data arrvies. Place connection in
accept queue when first data packet arrives from slow path.
Benefits:
- established connection is now reset if it never makes it
to the accept queue
- diagnostic state of established matches with the packet traces
showing completed handshake
- TCP_DEFER_ACCEPT timeouts are expressed in seconds and can now be
enforced with reasonable accuracy instead of rounding up to next
exponential back-off of syn-ack retry.
Signed-off-by: Patrick McManus <mcmanus@ducksong.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
a socket in LISTEN that had completed its 3 way handshake, but not notified
userspace because of SO_DEFER_ACCEPT, would retransmit the already
acked syn-ack during the time it was waiting for the first data byte
from the peer.
Signed-off-by: Patrick McManus <mcmanus@ducksong.com>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
timeout associated with SO_DEFER_ACCEPT wasn't being honored if it was
less than the timeout allowed by the maximum syn-recv queue size
algorithm. Fix by using the SO_DEFER_ACCEPT value if the ack has
arrived.
Signed-off-by: Patrick McManus <mcmanus@ducksong.com>
Acked-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a narrow pedantry :) but the dlci_ioctl_hook check and call
should not be parted with the mutex lock.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commits f40c81 ([NETNS][IPV4] tcp - make proc handle the network
namespaces) and a91275 ([NETNS][IPV6] udp - make proc handle the
network namespace) both introduced bad checks on sockets and tw
buckets to belong to proper net namespace.
I.e. when checking for socket to belong to given net and family the
do {
sk = sk_next(sk);
} while (sk && sk->sk_net != net && sk->sk_family != family);
constructions were used. This is wrong, since as soon as the
sk->sk_net fits the net the socket is immediately returned, even if it
belongs to other family.
As the result four /proc/net/(udp|tcp)[6] entries show wrong info.
The udp6 entry even oopses when dereferencing inet6_sk(sk) pointer:
static void udp6_sock_seq_show(struct seq_file *seq, struct sock *sp, int bucket)
{
...
struct ipv6_pinfo *np = inet6_sk(sp);
...
dest = &np->daddr; /* will be NULL for AF_INET sockets */
...
seq_printf(...
dest->s6_addr32[0], dest->s6_addr32[1],
dest->s6_addr32[2], dest->s6_addr32[3],
...
Fix it by converting && to ||.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
