summaryrefslogtreecommitdiffstats
path: root/net
AgeCommit message (Collapse)Author
2009-11-23sctp: implement the receiver side for SACK-IMMEDIATELY extensionWei Yongjun
This patch implement the receiver side for SACK-IMMEDIATELY extension: Section 4.2. Receiver Side Considerations On reception of an SCTP packet containing a DATA chunk with the I-bit set, the receiver SHOULD NOT delay the sending of the corresponding SACK chunk and SHOULD send it back immediately. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
2009-11-23net/ipv4: Move && and || to end of previous lineJoe Perches
On Sun, 2009-11-22 at 16:31 -0800, David Miller wrote: > It should be of the form: > if (x && > y) > > or: > if (x && y) > > Fix patches, rather than complaints, for existing cases where things > do not follow this pattern are certainly welcome. Also collapsed some multiple tabs to single space. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-23pktgen: Fix device name comparesEric Dumazet
Commit e6fce5b916cd7f7f7 (pktgen: multiqueue etc.) tried to relax the pktgen restriction of one device per kernel thread, adding a '@' tag to device names. Problem is we dont perform check on full pktgen device name. This allows adding many time same 'device' to pktgen thread pgset "add_device eth0@0" one session later : pgset "add_device eth0@0" (This doesnt find previous device) This consumes ~1.5 MBytes of vmalloc memory per round and also triggers this warning : [ 673.186380] proc_dir_entry 'pktgen/eth0@0' already registered [ 673.186383] Modules linked in: pktgen ixgbe ehci_hcd psmouse mdio mousedev evdev [last unloaded: pktgen] [ 673.186406] Pid: 6219, comm: bash Tainted: G W 2.6.32-rc7-03302-g41cec6f-dirty #16 [ 673.186410] Call Trace: [ 673.186417] [<ffffffff8104a29b>] warn_slowpath_common+0x7b/0xc0 [ 673.186422] [<ffffffff8104a341>] warn_slowpath_fmt+0x41/0x50 [ 673.186426] [<ffffffff8114e789>] proc_register+0x109/0x210 [ 673.186433] [<ffffffff8100bf2e>] ? apic_timer_interrupt+0xe/0x20 [ 673.186438] [<ffffffff8114e905>] proc_create_data+0x75/0xd0 [ 673.186444] [<ffffffffa006ad38>] pktgen_thread_write+0x568/0x640 [pktgen] [ 673.186449] [<ffffffffa006a7d0>] ? pktgen_thread_write+0x0/0x640 [pktgen] [ 673.186453] [<ffffffff81149144>] proc_reg_write+0x84/0xc0 [ 673.186458] [<ffffffff810f5a58>] vfs_write+0xb8/0x180 [ 673.186463] [<ffffffff810f5c11>] sys_write+0x51/0x90 [ 673.186468] [<ffffffff8100b51b>] system_call_fastpath+0x16/0x1b [ 673.186470] ---[ end trace ccbb991b0a8d994d ]--- Solution to this problem is to use a odevname field (includes @ tag and suffix), instead of using netdevice name. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: Robert Olsson <robert.olsson@its.uu.se> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-23Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kaber/nf-2.6
2009-11-23Merge commit 'v2.6.32-rc8' into HEADJ. Bruce Fields
2009-11-23Revert "knfsd: avoid overloading the CPU scheduler with enormous load averages"J. Bruce Fields
This reverts commit 59a252ff8c0f2fa32c896f69d56ae33e641ce7ad. This helps in an entirely cached workload but not necessarily in workloads that require waiting on disk. Conflicts: include/linux/sunrpc/svc.h net/sunrpc/svc_xprt.c Reported-by: Simon Kirby <sim@hostway.ca> Tested-by: Jesper Krogh <jesper@krogh.cc> Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
2009-11-23netfilter: xt_limit: fix invalid return code in limit_mt_check()Patrick McHardy
Commit acc738fe (netfilter: xtables: avoid pointer to self) introduced an invalid return value in limit_mt_check(). Signed-off-by: Patrick McHardy <kaber@trash.net>
2009-11-23netfilter: xtables: fix conntrack match v1 ipt-save outputFlorian Westphal
commit d6d3f08b0fd998b647a05540cedd11a067b72867 (netfilter: xtables: conntrack match revision 2) does break the v1 conntrack match iptables-save output in a subtle way. Problem is as follows: up = kmalloc(sizeof(*up), GFP_KERNEL); [..] /* * The strategy here is to minimize the overhead of v1 matching, * by prebuilding a v2 struct and putting the pointer into the * v1 dataspace. */ memcpy(up, info, offsetof(typeof(*info), state_mask)); [..] *(void **)info = up; As the v2 struct pointer is saved in the match data space, it clobbers the first structure member (->origsrc_addr). Because the _v1 match function grabs this pointer and does not actually look at the v1 origsrc, run time functionality does not break. But iptables -nvL (or iptables-save) cannot know that v1 origsrc_addr has been overloaded in this way: $ iptables -p tcp -A OUTPUT -m conntrack --ctorigsrc 10.0.0.1 -j ACCEPT $ iptables-save -A OUTPUT -p tcp -m conntrack --ctorigsrc 128.173.134.206 -j ACCEPT (128.173... is the address to the v2 match structure). To fix this, we take advantage of the fact that the v1 and v2 structures are identical with exception of the last two structure members (u8 in v1, u16 in v2). We extract them as early as possible and prevent the v2 matching function from looking at those two members directly. Previously reported by Michel Messerschmidt via Ben Hutchings, also see Debian Bug tracker #556587. Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Patrick McHardy <kaber@trash.net>
2009-11-23netfilter: nf_ct_tcp: improve out-of-sync situation in TCP trackingPablo Neira Ayuso
Without this patch, if we receive a SYN packet from the client while the firewall is out-of-sync, we let it go through. Then, if we see the SYN/ACK reply coming from the server, we destroy the conntrack entry and drop the packet to trigger a new retransmission. Then, the retransmision from the client is used to start a new clean session. This patch improves the current handling. Basically, if we see an unexpected SYN packet, we annotate the TCP options. Then, if we see the reply SYN/ACK, this means that the firewall was indeed out-of-sync. Therefore, we set a clean new session from the existing entry based on the annotated values. This patch adds two new 8-bits fields that fit in a 16-bits gap of the ip_ct_tcp structure. This patch is particularly useful for conntrackd since the asynchronous nature of the state-synchronization allows to have backup nodes that are not perfect copies of the master. This helps to improve the recovery under some worst-case scenarios. I have tested this by creating lots of conntrack entries in wrong state: for ((i=1024;i<65535;i++)); do conntrack -I -p tcp -s 192.168.2.101 -d 192.168.2.2 --sport $i --dport 80 -t 800 --state ESTABLISHED -u ASSURED,SEEN_REPLY; done Then, I make some TCP connections: $ echo GET / | nc 192.168.2.2 80 The events show the result: [UPDATE] tcp 6 60 SYN_RECV src=192.168.2.101 dst=192.168.2.2 sport=33220 dport=80 src=192.168.2.2 dst=192.168.2.101 sport=80 dport=33220 [ASSURED] [UPDATE] tcp 6 432000 ESTABLISHED src=192.168.2.101 dst=192.168.2.2 sport=33220 dport=80 src=192.168.2.2 dst=192.168.2.101 sport=80 dport=33220 [ASSURED] [UPDATE] tcp 6 120 FIN_WAIT src=192.168.2.101 dst=192.168.2.2 sport=33220 dport=80 src=192.168.2.2 dst=192.168.2.101 sport=80 dport=33220 [ASSURED] [UPDATE] tcp 6 30 LAST_ACK src=192.168.2.101 dst=192.168.2.2 sport=33220 dport=80 src=192.168.2.2 dst=192.168.2.101 sport=80 dport=33220 [ASSURED] [UPDATE] tcp 6 120 TIME_WAIT src=192.168.2.101 dst=192.168.2.2 sport=33220 dport=80 src=192.168.2.2 dst=192.168.2.101 sport=80 dport=33220 [ASSURED] and tcpdump shows no retransmissions: 20:47:57.271951 IP 192.168.2.101.33221 > 192.168.2.2.www: S 435402517:435402517(0) win 5840 <mss 1460,sackOK,timestamp 4294961827 0,nop,wscale 6> 20:47:57.273538 IP 192.168.2.2.www > 192.168.2.101.33221: S 3509927945:3509927945(0) ack 435402518 win 5792 <mss 1460,sackOK,timestamp 235681024 4294961827,nop,wscale 4> 20:47:57.273608 IP 192.168.2.101.33221 > 192.168.2.2.www: . ack 3509927946 win 92 <nop,nop,timestamp 4294961827 235681024> 20:47:57.273693 IP 192.168.2.101.33221 > 192.168.2.2.www: P 435402518:435402524(6) ack 3509927946 win 92 <nop,nop,timestamp 4294961827 235681024> 20:47:57.275492 IP 192.168.2.2.www > 192.168.2.101.33221: . ack 435402524 win 362 <nop,nop,timestamp 235681024 4294961827> 20:47:57.276492 IP 192.168.2.2.www > 192.168.2.101.33221: P 3509927946:3509928082(136) ack 435402524 win 362 <nop,nop,timestamp 235681025 4294961827> 20:47:57.276515 IP 192.168.2.101.33221 > 192.168.2.2.www: . ack 3509928082 win 108 <nop,nop,timestamp 4294961828 235681025> 20:47:57.276521 IP 192.168.2.2.www > 192.168.2.101.33221: F 3509928082:3509928082(0) ack 435402524 win 362 <nop,nop,timestamp 235681025 4294961827> 20:47:57.277369 IP 192.168.2.101.33221 > 192.168.2.2.www: F 435402524:435402524(0) ack 3509928083 win 108 <nop,nop,timestamp 4294961828 235681025> 20:47:57.279491 IP 192.168.2.2.www > 192.168.2.101.33221: . ack 435402525 win 362 <nop,nop,timestamp 235681025 4294961828> I also added a rule to log invalid packets, with no occurrences :-) . Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Acked-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu> Signed-off-by: Patrick McHardy <kaber@trash.net>
2009-11-22net: Fix missing kernel-doc notationJaswinder Singh Rajput
Fix the following htmldocs warning: Warning(net/core/dev.c:5378): bad line: Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-21tcp: Don't make syn cookies initial setting depend on CONFIG_SYSCTLDavid S. Miller
That's extremely non-intuitive, noticed by William Allen Simpson. And let's make the default be on, it's been suggested by a lot of people so we'll give it a try. Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-20net: rename skb->iif to skb->skb_iifEric Dumazet
To help grep games, rename iif to skb_iif Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-19Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6Linus Torvalds
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6: SUNRPC: Address buffer overrun in rpc_uaddr2sockaddr() NFSv4: Fix a cache validation bug which causes getcwd() to return ENOENT
2009-11-19RDMA/cm: fix loopback address supportSean Hefty
The RDMA CM is intended to support the use of a loopback address when establishing a connection; however, the behavior of the CM when loopback addresses are used is confusing and does not always work, depending on whether loopback was specified by the server, the client, or both. The defined behavior of rdma_bind_addr is to associate an RDMA device with an rdma_cm_id, as long as the user specified a non- zero address. (ie they weren't just trying to reserve a port) Currently, if the loopback address is passed to rdam_bind_addr, no device is associated with the rdma_cm_id. Fix this. If a loopback address is specified by the client as the destination address for a connection, it will fail to establish a connection. This is true even if the server is listing across all addresses or on the loopback address itself. The issue is that the server tries to translate the IP address carried in the REQ message to a local net_device address, which fails. The translation is not needed in this case, since the REQ carries the actual HW address that should be used. Finally, cleanup loopback support to be more transport neutral. Replace separate calls to get/set the sgid and dgid from the device address to a single call that behaves correctly depending on the format of the device address. And support both IPv4 and IPv6 address formats. Signed-off-by: Sean Hefty <sean.hefty@intel.com> [ Fixed RDS build by s/ib_addr_get/rdma_addr_get/ - Roland ] Signed-off-by: Roland Dreier <rolandd@cisco.com>
2009-11-19netfilter: nf_log: fix sleeping function called from invalid context in ↵Patrick McHardy
seq_show() [ 171.925285] BUG: sleeping function called from invalid context at kernel/mutex.c:280 [ 171.925296] in_atomic(): 1, irqs_disabled(): 0, pid: 671, name: grep [ 171.925306] 2 locks held by grep/671: [ 171.925312] #0: (&p->lock){+.+.+.}, at: [<c10b8acd>] seq_read+0x25/0x36c [ 171.925340] #1: (rcu_read_lock){.+.+..}, at: [<c1391dac>] seq_start+0x0/0x44 [ 171.925372] Pid: 671, comm: grep Not tainted 2.6.31.6-4-netbook #3 [ 171.925380] Call Trace: [ 171.925398] [<c105104e>] ? __debug_show_held_locks+0x1e/0x20 [ 171.925414] [<c10264ac>] __might_sleep+0xfb/0x102 [ 171.925430] [<c1461521>] mutex_lock_nested+0x1c/0x2ad [ 171.925444] [<c1391c9e>] seq_show+0x74/0x127 [ 171.925456] [<c10b8c5c>] seq_read+0x1b4/0x36c [ 171.925469] [<c10b8aa8>] ? seq_read+0x0/0x36c [ 171.925483] [<c10d5c8e>] proc_reg_read+0x60/0x74 [ 171.925496] [<c10d5c2e>] ? proc_reg_read+0x0/0x74 [ 171.925510] [<c10a4468>] vfs_read+0x87/0x110 [ 171.925523] [<c10a458a>] sys_read+0x3b/0x60 [ 171.925538] [<c1002a49>] syscall_call+0x7/0xb Fix it by replacing RCU with nf_log_mutex. Reported-by: "Yin, Kangkai" <kangkai.yin@intel.com> Signed-off-by: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-19netfilter: xt_osf: fix xt_osf_remove_callback() return valuePatrick McHardy
Return a negative error value. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: Patrick McHardy <kaber@trash.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-19mac80211: fix endianess on mesh_path_error_tx() callsRui Paulo
Signed-off-by: Rui Paulo <rpaulo@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-19mac80211: add per-station HT capability fileJohannes Berg
This is sometimes useful to debug HT issues as it shows what exactly the stack thinks the peer supports. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-19mac80211: avoid spurious deauth frames/messagesJohannes Berg
With WEXT, it happens frequently that the SME requests an authentication but then deauthenticates right away because some new parameters came along. Every time this happens we print a deauth message and send a deauth frame, but both of that is rather confusing. Avoid it by aborting the authentication process silently, and telling cfg80211 about that. The patch looks larger than it really is: __cfg80211_auth_remove() is split out from cfg80211_send_auth_timeout(), there's no new code except __cfg80211_auth_canceled() (a one-liner) and the mac80211 bits (7 new lines of code). Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-19mac80211: request TX status where neededJohannes Berg
Right now all frames mac80211 hands to the driver have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set to request TX status. This isn't really necessary, only the injected frames need TX status (the latter for hostapd) so move setting this flag. The rate control algorithms also need TX status, but they don't require it. Also, rt2x00 uses that bit for its own purposes and seems to require it being set for all frames, but that can be fixed in rt2x00. This doesn't really change anything for any drivers but in the future drivers using hw-rate control may opt to not report TX status for frames that don't have the IEEE80211_TX_CTL_REQ_TX_STATUS flag set. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> [rt2x00 bits] Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-19cfg80211: disallow bridging managed/adhoc interfacesJohannes Berg
A number of people have tried to add a wireless interface (in managed mode) to a bridge and then complained that it doesn't work. It cannot work, however, because in 802.11 networks all packets need to be acknowledged and as such need to be sent to the right address. Promiscuous doesn't help here. The wireless address format used for these links has only space for three addresses, the * transmitter, which must be equal to the sender (origin) * receiver (on the wireless medium), which is the AP in the case of managed mode * the recipient (destination), which is on the APs local network segment In an IBSS, it is similar, but the receiver and recipient must match and the third address is used as the BSSID. To avoid such mistakes in the future, disallow adding a wireless interface to a bridge. Felix has recently added a four-address mode to the AP and client side that can be used (after negotiating that it is possible, which must happen out-of-band by setting up both sides) for bridging, so allow that case. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Acked-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-19cfg80211: introduce capability for 4addr modeJohannes Berg
It's very likely that not many devices will support four-address mode in station or AP mode so introduce capability bits for both modes, set them in mac80211 and check them when userspace tries to use the mode. Also, keep track of 4addr in cfg80211 (wireless_dev) and not in mac80211 any more. mac80211 can also be improved for the VLAN case by not looking at the 4addr flag but maintaining the station pointer for it correctly. However, keep track of use_4addr for station mode in mac80211 to avoid all the derefs. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-19cfg80211: convert bools into flagsJohannes Berg
We've accumulated a number of options for wiphys which make more sense as flags as we keep adding more. Convert the existing ones. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-19mac80211: fix resumeJohannes Berg
When mac80211 resumes, it currently first sets suspended to false so the driver can start doing things and we can receive frames. However, if we actually receive frames then it can end up starting some work which adds timers and then later runs into a BUG_ON in the timer code because it tries add_timer() on a pending timer. Fix this by keeping track of the resuming process by introducing a new variable 'resuming' which gets set to true early on instead of setting 'suspended' to false, and allow queueing work but not receiving frames while resuming. Reported-by: Maxim Levitsky <maximlevitsky@gmail.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18X25: Enable setting of cause and diagnostic fieldsAndrew Hendry
Adds SIOCX25SCAUSEDIAG, allowing X.25 programs to set the cause and diagnostic fields. Normally used to indicate status upon closing connections. Signed-off-by: Andrew Hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-18netsched: Allow var_sk_bound_if meta to work on all namespacesEric Dumazet
This fix can probably wait 2.6.33, or should use another patch if needed in 2.6.32 (no get_dev_by_index_rcu() before 2.6.33) Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-18Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/sfc/sfe4001.c drivers/net/wireless/libertas/cmd.c drivers/staging/Kconfig drivers/staging/Makefile drivers/staging/rtl8187se/Kconfig drivers/staging/rtl8192e/Kconfig
2009-11-18Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (42 commits) cxgb3: fix premature page unmap ibm_newemac: Fix EMACx_TRTR[TRT] bit shifts vlan: Fix register_vlan_dev() error path gro: Fix illegal merging of trailer trash sungem: Fix Serdes detection. net: fix mdio section mismatch warning ppp: fix BUG on non-linear SKB (multilink receive) ixgbe: Fixing EEH handler to handle more than one error net: Fix the rollback test in dev_change_name() Revert "isdn: isdn_ppp: Use SKB list facilities instead of home-grown implementation." TI Davinci EMAC : Fix Console Hang when bringing the interface down smsc911x: Fix Console Hang when bringing the interface down. mISDN: fix error return in HFCmulti_init() forcedeth: mac address fix r6040: fix version printing Bluetooth: Fix regression with L2CAP configuration in Basic Mode Bluetooth: Select Basic Mode as default for SOCK_SEQPACKET Bluetooth: Set general bonding security for ACL by default r8169: Fix receive buffer length when MTU is between 1515 and 1536 can: add the missing netlink get_xstats_size callback ...
2009-11-18mac80211: update cfg80211 scan result code for the updated mesh conf IERui Paulo
Signed-off-by: Rui Paulo <rpaulo@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: use a structure to hold the mesh config information elementRui Paulo
Signed-off-by: Rui Paulo <rpaulo@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: move TX status handlingJohannes Berg
It's enough code to have its own file, I think. Especially since I'm going to add to it. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: remove encrypt parameter from ieee80211_tx_skbJohannes Berg
Since the flags moved into skb->cb, there's no longer a need to have the encrypt bool passed into the function, anyone who requires it set to 0 (false) can just set the flag directly. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18rfkill: Add constant for RFKILL_TYPE_FM radio devicesMarcel Holtmann
Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Janakiram Sistla <janakiram.sistla@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18cfg80211: re-join IBSS when privacy changesJohannes Berg
When going from/to a WEP protected IBSS, we need to leave this one and join a new one to take care of the changed capability. Cc: Hong Zhang <henryzhang62@yahoo.com> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: Fix panic in aggregation handlingSujith
Not assigning the vif pointer causes an oops. This patch fixes it. Signed-off-by: Sujith <Sujith.Manoharan@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18cfg80211: Allow reassociation in associated stateJouni Malinen
cfg80211 rejects all association requests when in associated state. This prevents clean roaming within an ESS since one would first need to disassociate before being able to request reassociation. Accept the reassociation request and let the old association to be dropped when the new one is completed. This fixes nl80211-based roaming with the current snapshot version of wpa_supplicant (that has code for requesting reassociation explicitly withthe previous BSSID attribute). Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: make software rate control optionalJohannes Berg
Some devices implement the entire rate control in firmware in some way, like wl1271 or like iwlwifi which does some things in software but not a lot. Therefore generic software rate control is rather useless for them and just adds avoidable overhead to the transmit path. It's fairly simple to let drivers indicate that they do not need rate control, but they need to fulfil a number of conditions that we encode in WARN_ONs. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: use fixed broadcast addressJohannes Berg
The netdev broadcast address cannot change from all-ones so there's no need to use it; we can instead hard-code it. Since we already have an instance in tkip.c, which will be shared if it is marked static const, doing this reduces text size at no data/bss cost. The real motivation for this is, of course, the desire to get rid of almost all uses of netdevs in mac80211 so that auditing their use becomes easier. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: remove dev_hold/put callsJohannes Berg
If we move the rcu sections a little, there's no need to touch the device refcount. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: improve rate handlingJohannes Berg
Some code currently assumes that there's a valid rate pointer even in the HT case, but there can't be. To reduce reliance on that, remove the rate pointer from the RX data struct and pass it where it's needed. Also, for now, in radiotap announce HT frames as having a DYN channel type, and remove their rate from cooked monitor radiotap completely (it isn't present in the regular monitor radiotap either.) Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: trim RX dataJohannes Berg
The RX data contains the netdev, which is duplicated since we have the sdata, and the RX status pointer, which is duplicate since we have the skb. Remove those two fields to have fewer fields that depend on each other and simply load them as necessary. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: cleanup reorder buffer handlingJohannes Berg
The reorder buffer handling is written in a quite peculiar style (especially comments) and also has a quirk where it invokes the entire reorder code in ieee80211_sta_manage_reorder_buf() for just a handful of lines in it with a special argument. Split out ieee80211_release_reorder_frames which can then be invoked from BAR handling and other reordering code, clean up code and comments and remove function arguments that are now unused from ieee80211_sta_manage_reorder_buf(). Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: push michael MIC report after DA checkJohannes Berg
When we receive a michael MIC failure report from the hardware we currently do not check whether it is actually reported on a frame that is destined to us. It shouldn't be possible to get a michael MIC failure report on other frames, but it also doesn't hurt to verify. Also, since we then don't need the station struct that early, move looking it up a bit later in the RX path. Finally, while at it, a few code cleanups in the area. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: convert aggregation to operate on vifs/stasJohannes Berg
The entire aggregation code currently operates on the hw pointer and station addresses, but that needs to change to make stations purely per-vif; As one step preparing for that make the aggregation code callable with the station, or by the combination of virtual interface and station address. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: let sta_info_get_by_idx get sta by sdataJohannes Berg
Instead of filtering by device, directly look up by sdata. Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: reduce the amount of unnecessary traffic on cooked monitor interfacesFelix Fietkau
In order to handle association and authentication in AP mode, hostapd needs access to the tx status info of its own frames through a cooked monitor interface. Without this patch the cooked monitor interfaces also passed on tx status information for packets from other virtual interfaces. This creates a significant performance issue on embedded system. Hostapd tries to work around this by installing a Linux Socket Filter that only captures the frames it's interested in, however data duplication and socket filter matching still uses up enough CPU cycles to be very noticeable on small systems. This patch ensures that tx status information of non-injected frames does not make it to cooked monitor interfaces. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18mac80211: fix addba timer (again...)Johannes Berg
commit 2171abc58644e09dbba546d91366b12743115396 Author: Johannes Berg <johannes@sipsolutions.net> Date: Thu Oct 29 08:34:00 2009 +0100 mac80211: fix addba timer left a problem in there, even if the timer was never started it could be deleted and then added. Linus pointed out that del_timer_sync() isn't actually needed if we make the timer able to deal with no longer being needed when it gets queued _while_ we're in the locked section that also deletes it. For that the timer function only needs to check the HT_ADDBA_RECEIVED_MSK bit as well as the HT_ADDBA_REQUESTED_MSK bit, only if the former is clear should it do anything. Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2009-11-18Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2009-11-18Phonet: convert devices list to RCURémi Denis-Courmont
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-11-18sysctl: Drop & in front of every proc_handler.Eric W. Biederman
For consistency drop & in front of every proc_handler. Explicity taking the address is unnecessary and it prevents optimizations like stubbing the proc_handlers to NULL. Cc: Alexey Dobriyan <adobriyan@gmail.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Joe Perches <joe@perches.com> Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>