Age | Commit message (Collapse) | Author |
|
This only happened when parse_extra_token was not passed
to ceph_parse_option() (hence, only happened in rbd).
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
|
|
These facilitate preallocation of pages so that we can encode into the pagelist
in an atomic context.
Signed-off-by: Greg Farnum <gregf@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
|
|
The rados block device (rbd), based on osdblk, creates a block device
that is backed by objects stored in the Ceph distributed object storage
cluster. Each device consists of a single metadata object and data
striped over many data objects.
The rbd driver supports read-only snapshots.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
|
|
This factors out protocol and low-level storage parts of ceph into a
separate libceph module living in net/ceph and include/linux/ceph. This
is mostly a matter of moving files around. However, a few key pieces
of the interface change as well:
- ceph_client becomes ceph_fs_client and ceph_client, where the latter
captures the mon and osd clients, and the fs_client gets the mds client
and file system specific pieces.
- Mount option parsing and debugfs setup is correspondingly broken into
two pieces.
- The mon client gets a generic handler callback for otherwise unknown
messages (mds map, in this case).
- The basic supported/required feature bits can be expanded (and are by
ceph_fs_client).
No functional change, aside from some subtle error handling cases that got
cleaned up in the refactoring process.
Signed-off-by: Sage Weil <sage@newdream.net>
|
|
There is no point using RCU for dst we allocate for a very short time
(used once).
Change dst_release() to take DST_NOCACHE into account, but also change
skb_dst_set_noref() to force a refcount increment for such dst.
This is a _huge_ gain, because we dont waste memory to store xx thousand
of dsts. Instead of queueing them to RCU, we can free them instantly.
CPU caches can stay hot, re-using same memory blocks to hold temporary
dsts.
Note : remove unneeded smp_mb__before_atomic_dec(); in dst_release(),
since atomic_dec_return() implies a full memory barrier.
Stress test, 160.000.000 udp frames sent, IP route cache disabled
(DDOS).
Before:
real 0m38.091s
user 0m13.189s
sys 7m53.018s
After:
real 0m29.946s
user 0m12.157s
sys 7m40.605s
For reference, if IP route cache was enabled :
real 0m32.030s
user 0m10.521s
sys 8m15.243s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces netif_alloc_netdev_queues which is called from
register_device instead of alloc_netdev_mq. This makes TX queue
allocation symmetric with RX allocation. Also, queue locks allocation
is done in netdev_init_one_queue. Change set_real_num_tx_queues to
fail if requested number < 1 or greater than number of allocated
queues.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clean up in RX queue allocation. In netif_set_real_num_rx_queues
return error on attempt to set zero queues, or requested number is
greater than number of allocated queues. In netif_alloc_rx_queues,
do BUG_ON if queue_count is zero.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In alloc_netdev_mq fail if requested queue_count < 1.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
|
|
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In an erlier patch I modified napi_poll so that devices with IFF_MASTER polled
the per_cpu list instead of the device list for napi. I did this because the
bonding driver has no napi instances to poll, it instead expects to check the
slave devices napi instances, which napi_poll was unaware of. Looking at this
more closely however, I now see this isn't strictly needed. As the bond driver
poll_controller calls the slaves poll_controller via netpoll_poll_dev, which
recursively calls poll_napi on each slave, allowing those napi instances to get
serviced. The earlier patch isn't at all harmfull, its just not needed, so lets
revert it to make the code cleaner. Sorry for the noise,
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lists were initialized after the module was registered. Multiple ipvsadm
processes at module load triggered a race condition that resulted in a null
pointer dereference in do_ip_vs_get_ctl(). As a result, __ip_vs_mutex
was left locked preventing all further ipvsadm commands.
Signed-off-by: Eduardo J. Blanco <ejblanco@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Saves some lines of code and some branticks when reading one.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Since the xprt in question is forcibly set to be bound the else
branch of this check is unneeded.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
> The reason for this is in the future, we may want to support additional
> address family types. We should, therefore, ensure that every piece of
> code that is sensitive to address families fail in some orderly manner
> to let developers know where a change is needed.
Makes sense. I was under impression, that AF-s other than INET are not
cared about at all :(
Here's a fixed version of the patch.
Log:
Its callers check for ERR_PTR.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
The task in question is dereferenced above (and is actually never NULL).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Same for UDP sockets creation paths.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
The v4 and the v6 wrappers only pass the respective family
to the xs_tcp_setup_socket. This family can be taken from the
xprt's sockaddr.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Now we have a single socket creation routine and can call it
directly from the setup_socket routines.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
After xs_bind is merged it's easy to merge its callers.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
[bfields@redhat.com: fix address family initialization]
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
There's the only difference betseen the xs_bind4 and the
xs_bind6 - the size of sockaddr structure they use.
Fortunatelly its size can be indirectly get from the transport.
Change since v1:
* use sockaddr_storage instead of sockaddr
* use rpc_set_port instead of manual port assigning
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
[bfields@redhat.com: fix address family initialization]
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Remove now unneeded wrappers that just add type and protocol
to socket creation callback.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Same patch for v6 protocols.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
The UDPv4 and TCPv4 socket creation callbacks now look very similar.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Make it look like the TCP sockets creation.
Unfortunately the git diff made the patch look messy :(
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
The xs_tcp_reuse_connection takes the xprt only to pass it down
to the xs_abort_connection. The later one can get it from the given
transport itself.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Convert inetdev_by_index() to not increment in_dev refcount.
Callers hold RCU or RTNL, and should not decrement in_dev refcount.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We hold RTNL in ip_mc_find_dev(), no need to touch device refcount.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The sunrpc cache_ioctl function does not need the big kernel lock
because it uses its own queue_lock already.
rpc_pipe_ioctl apparently should be using i_lock like the other
operations on the pipe file descriptor do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
IPv6 encapsulation uses a bad source address for the tunnel.
i.e. VIP will be used as local-addr and encap. dst addr.
Decapsulation will not accept this.
Example
LVS (eth1 2003::2:0:1/96, VIP 2003::2:0:100)
(eth0 2003::1:0:1/96)
RS (ethX 2003::1:0:5/96)
tcpdump
2003::2:0:100 > 2003::1:0:5: IP6 (hlim 63, next-header TCP (6) payload length: 40) 2003::3:0:10.50991 > 2003::2:0:100.http: Flags [S], cksum 0x7312 (correct), seq 3006460279, win 5760, options [mss 1440,sackOK,TS val 1904932 ecr 0,nop,wscale 3], length 0
In Linux IPv6 impl. you can't have a tunnel with an any cast address
receiving packets (I have not tried to interpret RFC 2473)
To have receive capabilities the tunnel must have:
- Local address set as multicast addr or an unicast addr
- Remote address set as an unicast addr.
- Loop back addres or Link local address are not allowed.
This causes us to setup a tunnel in the Real Server with the
LVS as the remote address, here you can't use the VIP address since it's
used inside the tunnel.
Solution
Use outgoing interface IPv6 address (match against the destination).
i.e. use ip6_route_output() to look up the route cache and
then use ipv6_dev_get_saddr(...) to set the source address of the
encapsulated packet.
Additionally, cache the results in new destination
fields: dst_cookie and dst_saddr and properly check the
returned dst from ip6_route_output. We now add xfrm_lookup
call only for the tunneling method where the source address
is a local one.
Signed-off-by:Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
This patch allows to listen to events that inform about
expectations destroyed.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
There are several error paths in the code that do not unmap DMA. This
patch adds calls to svc_rdma_unmap_dma to free these DMA contexts.
Signed-off-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
There was logic in the send path that assumed that a page containing data
to send to the client has a KVA. This is not always the case and can result
in data corruption when page_address returns zero and we end up DMA mapping
zero.
This patch changes the bus mapping logic to avoid page_address() where
necessary and converts all calls from ib_dma_map_single to ib_dma_map_page
in order to keep the map/unmap calls symmetric.
Signed-off-by: Tom Tucker <tom@ogc.us>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Peter Zijlstra found a bug in the way softirq time is accounted in
VIRT_CPU_ACCOUNTING on this thread:
http://lkml.indiana.edu/hypermail//linux/kernel/1009.2/01366.html
The problem is, softirq processing uses local_bh_disable internally. There
is no way, later in the flow, to differentiate between whether softirq is
being processed or is it just that bh has been disabled. So, a hardirq when bh
is disabled results in time being wrongly accounted as softirq.
Looking at the code a bit more, the problem exists in !VIRT_CPU_ACCOUNTING
as well. As account_system_time() in normal tick based accouting also uses
softirq_count, which will be set even when not in softirq with bh disabled.
Peter also suggested solution of using 2*SOFTIRQ_OFFSET as irq count
for local_bh_{disable,enable} and using just SOFTIRQ_OFFSET while softirq
processing. The patch below does that and adds API in_serving_softirq() which
returns whether we are currently processing softirq or not.
Also changes one of the usages of softirq_count in net/sched/cls_cgroup.c
to in_serving_softirq.
Looks like many usages of in_softirq really want in_serving_softirq. Those
changes can be made individually on a case by case basis.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1286237003-12406-2-git-send-email-venki@google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Usually the netpoll path, when preforming a napi poll can get away with just
polling all the napi instances of the configured device. Thats not the case for
the bonding driver however, as the napi instances which may wind up getting
flagged as needing polling after the poll_controller call don't belong to the
bonded device, but rather to the slave devices. Fix this by checking the device
in question for the IFF_MASTER flag, if set, we know we need to check the full
poll list for this cpu, rather than just the devices napi instance list.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bonding driver currently modifies the netpoll structure in its xmit path
while sending frames from netpoll. This is racy, as other cpus can access the
netpoll structure in parallel. Since the bonding driver points np->dev to a
slave device, other cpus can inadvertently attempt to send data directly to
slave devices, leading to improper locking with the bonding master, lost frames,
and deadlocks. This patch fixes that up.
This patch also removes the real_dev pointer from the netpoll structure as that
data is really only used by bonding in the poll_controller, and we can emulate
its behavior by check each slave for IS_UP.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change a few checks against the hardcoded broadcast address,
0xffffffff, to ipv4_is_lbcast(). Remove some existing checks
using ipv4_is_lbcast() that are now obviously superfluous.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix netfilter kconfig unmet dependencies warning & spell out
"compatible" while there.
warning: (IP_NF_TARGET_TTL && NET && INET && NETFILTER && IP_NF_IPTABLES && NETFILTER_ADVANCED || IP6_NF_TARGET_HL && NET && INET && IPV6 && NETFILTER && IP6_NF_IPTABLES && NETFILTER_ADVANCED) selects NETFILTER_XT_TARGET_HL which has unmet direct dependencies ((IP_NF_MANGLE || IP6_NF_MANGLE) && NETFILTER_ADVANCED)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
|
|
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Optimize processing in TIPC's bearer shutdown code, including:
1. Remove an unnecessary check to see if TIPC bearer's can exist.
2. Don't release spinlocks before calling a media-specific disabling
routine, since the routine can't sleep.
3. Make bearer_disable() operate directly on a struct bearer, instead
of needlessly taking a name and then mapping that to the struct.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's completely unused and exporting a static symbol
makes no sense and breaks the build.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In error cases when the ACL is insecure or we fail to allocate a new
struct sock, we jump to the "response" label. If so, "sk" will be
null and the kernel crashes.
Signed-off-by: Nathan Holstein <nathan.holstein@gmail.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Get rid of fib_hash_lock rwlock.
The fn_zone hash table resize is the noticeable part of this patch.
I added a seqlock per fn_zone, so that readers can restart their lookup
in the (very rare) case a writer expanded the hash table.
Add rcu heads in fib_alias and fib_node, use call_rcu() to defer their
freeing, and use appropriate _rcu list manipulations.
Stress test (160.000.000 udp frames sent, IP route cache disabled to
mimic DDOS attack, FIB_HASH)
Before:
real 0m41.191s
user 0m13.137s
sys 8m55.241s
After:
real 0m38.091s
user 0m13.189s
sys 7m53.018s
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
First step for RCU conversion of fib_hash :
struct fn_zone are created and never deleted.
Very classic conversion, using rcu_assign_pointer(), rcu_dereference()
and rtnl_dereference() verbs.
__rcu markers on fz_next and fn_zone_list
They are created under RTNL, we dont need fib_hash_lock anymore in
fn_new_zone().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While looking for false sharing problems, I noticed
sizeof(struct fn_zone) was small (28 bytes) and possibly sharing a cache
line with an often written kernel structure.
Most of the time, fn_zone uses its initial hash table of 16 slots.
We can avoid the false sharing problem by embedding this initial hash
table in fn_zone itself, so that sizeof(fn_zone) > L1_CACHE_BYTES
We did a similar optimization in commit a6501e080c (Reduce memory needs
and speedup lookups)
Add a fz_revorder field to speedup fn_hash() a bit.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As CWR is stronger than CA_Disorder state, we can miscount
SACK/Reno failure into other timeouts. Not a bad problem as
it can happen only due to ECN, FRTO detecting spurious RTO
or xmit error which are the only callers of tcp_enter_cwr.
And even then losses and RTO must still follow thereafter
to actually end up into the relevant code paths.
Compile tested.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When only fast rexmit should be done, tcp_mark_head_lost marks
L too far. Also, sacked_upto below 1 is perfectly valid number,
the packets == 0 then needs to be trapped elsewhere.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|