| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into wireless
John W. Linville says:
====================
Here are some more fixes intended for the 3.9 stream...
Regarding the mac80211 bits, Johannes says:
"I had changed the idle handling to simplify it, but broken the
sequencing of commands, at least for ath9k-htc, one patch restores the
sequence. The other patch fixes a crash Jouni found while stress-testing
the remain-on-channel code, when an item is deleted the work struct can
run twice and crash the second time."
As for the iwlwifi bits, Johannes says:
"The only fix here is to the passive-no-RX firmware regulatory
enforcement driver support code to not drop auth frames in quick
succession, leading to not being able to connect to APs on passive
channels in certain circumstances."
Don't forget the NFC bits, about which Samuel says:
"This time we have:
- A crash fix for when a DGRAM LLCP socket is listening while the NFC adapter
is physically removed.
- A potential double skb free when the LLCP socket receive queue is full.
- A fix for properly handling multiple and consecutive LLCP connections, and
not trash the socket ack log.
- A build failure for the MEI microread physical layer, now that the MEI bus
APIs have been merged into char-misc-next."
On top of that, Stone Piao provides an mwifiex fix to avoid accessing
beyond the end of a buffer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements per hash bucket locking for the frag queue
hash. This removes two write locks, and the only remaining write
lock is for protecting hash rebuild. This essentially reduce the
readers-writer lock to a rebuild lock.
This patch is part of "net: frag performance followup"
http://thread.gmane.org/gmane.linux.network/263644
of which two patches have already been accepted:
Same test setup as previous:
(http://thread.gmane.org/gmane.linux.network/257155)
Two 10G interfaces, on seperate NUMA nodes, are under-test, and uses
Ethernet flow-control. A third interface is used for generating the
DoS attack (with trafgen).
Notice, I have changed the frag DoS generator script to be more
efficient/deadly. Before it would only hit one RX queue, now its
sending packets causing multi-queue RX, due to "better" RX hashing.
Test types summary (netperf UDP_STREAM):
Test-20G64K == 2x10G with 65K fragments
Test-20G3F == 2x10G with 3x fragments (3*1472 bytes)
Test-20G64K+DoS == Same as 20G64K with frag DoS
Test-20G3F+DoS == Same as 20G3F with frag DoS
Test-20G64K+MQ == Same as 20G64K with Multi-Queue frag DoS
Test-20G3F+MQ == Same as 20G3F with Multi-Queue frag DoS
When I rebased this-patch(03) (on top of net-next commit a210576c) and
removed the _bh spinlock, I saw a performance regression. BUT this
was caused by some unrelated change in-between. See tests below.
Test (A) is what I reported before for patch-02, accepted in commit 1b5ab0de.
Test (B) verifying-retest of commit 1b5ab0de corrospond to patch-02.
Test (C) is what I reported before for this-patch
Test (D) is net-next master HEAD (commit a210576c), which reveals some
(unknown) performance regression (compared against test (B)).
Test (D) function as a new base-test.
Performance table summary (in Mbit/s):
(#) Test-type: 20G64K 20G3F 20G64K+DoS 20G3F+DoS 20G64K+MQ 20G3F+MQ
---------- ------- ------- ---------- --------- -------- -------
(A) Patch-02 : 18848.7 13230.1 4103.04 5310.36 130.0 440.2
(B) 1b5ab0de : 18841.5 13156.8 4101.08 5314.57 129.0 424.2
(C) Patch-03v1: 18838.0 13490.5 4405.11 6814.72 196.6 461.6
(D) a210576c : 18321.5 11250.4 3635.34 5160.13 119.1 405.2
(E) with _bh : 17247.3 11492.6 3994.74 6405.29 166.7 413.6
(F) without bh: 17471.3 11298.7 3818.05 6102.11 165.7 406.3
Test (E) and (F) is this-patch(03), with(V1) and without(V2) the _bh spinlocks.
I cannot explain the slow down for 20G64K (but its an artificial
"lab-test" so I'm not worried). But the other results does show
improvements. And test (E) "with _bh" version is slightly better.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
----
V2:
- By analysis from Hannes Frederic Sowa and Eric Dumazet, we don't
need the spinlock _bh versions, as Netfilter currently does a
local_bh_disable() before entering inet_fragment.
- Fold-in desc from cover-mail
V3:
- Drop the chain_len counter per hash bucket.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RPC_AUTH_MAXFLAVOR is an invalid flavor, on purpose. Don't allow
any processing whatsoever if a caller passes it to rpcauth_create()
or rpcauth_get_gssinfo().
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
|
|
The driver init queue is no longer needed. This can be all handled
inside the drivers now. So remove it.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Some drivers require a special stage for their early init. This is
always specific to the driver or transport. So call back into driver to
allow bringing up the device.
The advantage with this stage is that the Bluetooth core is actually
handling the HCI layer now. This means that command and event processing
is available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
This patch adds a __hci_cmd_sync_ev function, analogous to
__hci_cmd_sync except that it also takes an event parameter to indicate
that the command completes with a special event instead of command
complete. Internally this new function takes advantage of the
hci_req_add_ev function introduced in the previous patch.
The primary expected user of this new function are the setup routines of
HCI drivers which may want to send custom commands and return only when
they have completed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds support for having commands within HCI requests that do
not result in a command complete but some other event. This is at least
needed for some vendor specific commands to be issued in the
hdev->setup() procecure, but might also be useful for other commands.
The way that the support is implemented is by extending the skb control
buffer to have a field to indicate that the command is expected to
terminate with a special event. After sending the command each received
event can then be compared against this field through hdev->sent_cmd.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds a helper function for sending a single HCI command
waiting for its completion and then returning back the parameters in the
resulting command complete event (if there was one).
The implementation is very similar to that of hci_req_sync() except that
instead of invocing a callback for sending HCI commands the function
constructs and sends one itself and after being woken up picks the last
received event from hdev->recv_evt (if it matches the right criteria)
and returns it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds tracking of received HCI events to the hci_dev struct.
This is necessary so that a subsequent patch can implement a function
for sending a single command synchronously and returning the resulting
command complete parameters in the function return value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch removes the hci_req_cmd_status function since it is not
used anymore. The HCI request framework now considers the HCI command
has complete once the Command Status or Command Complete Event is
received.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Since the HCI request framework was properly fixed, the hci_req_sync
call, in hci_inquiry, will return as soon as the HCI command completes
(not the Inquiry procedure). However, in inquiry ioctl implementation,
we want to sleep the user process until the inquiry procedure finishes.
This patch changes hci_inquiry so, in case the HCI Inquiry command
was executed successfully, it waits the HCI_INQUIRY flag to be cleared.
This way, the user process will sleep until the inquiry procedure
finishes.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Some HCI commands don't send a Command Complete Event once the HCI
command has completed so they require some special handling from the
HCI request framework. These HCI commands, however, send a Command
Status Event to indicate that the command has been received, and
that the controller is currently performing the task for the command.
So, in order to properly handle those HCI commands, the HCI request
framework should consider the HCI command has completed once the
Command Status Event is received.
This way, we fix some issues regarding the Inquiry command support,
as well as add support for all those HCI commands which would require
some special handling from the HCI request framework.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
If kmalloc() fails in cache_open(), module cd->owner left locked.
The patch adds module_put(cd->owner) on this path.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
The bitmask used for the prefix mangling was being calculated
incorrectly, leading to the wrong part of the address being replaced
when the prefix length wasn't a multiple of 32.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Pull net into net-next to get the synchronize_net() bug fix in
bonding.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The port specific options are currently unused resulting in an
empty OVS_VPORT_ATTR_OPTIONS nested attribute being inserted
into every OVS_VPORT_CMD_GET message.
Don't insert OVS_VPORT_ATTR_OPTIONS if no options are present.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
Commit 7d4c04fc170087119727119074e72445f2bb192b ("net: add option to enable
error queue packets waking select") has an issue due to operator precedence
causing the bit-wise OR to bind to the sock_flags call instead of the result of
the terniary conditional. This fixes the *_poll functions to work properly. The
old code results in "mask |= POLLPRI" instead of what was intended, which is to
only include POLLPRI when the socket option is enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The VMCI context ID of a virtual machine may change at any time. There
is a VMCI event which signals this but datagrams may be processed before
this is handled. It is therefore necessary to be flexible about the
destination context ID of any datagrams received. (It can be assumed to
be correct because it is provided by the hypervisor.) The context ID on
existing sockets should be updated to reflect how the hypervisor is
currently referring to the system.
Signed-off-by: Reilly Grant <grantr@vmware.com>
Acked-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 Routing table becomes broken once we do ifdown, ifup of the loopback(lo)
interface. After down-up, routes of other interface's IPv6 addresses through
'lo' are lost.
IPv6 addresses assigned to all interfaces are routed through 'lo' for internal
communication. Once 'lo' is down, those routing entries are removed from routing
table. But those removed entries are not being re-created properly when 'lo' is
brought up. So IPv6 addresses of other interfaces becomes unreachable from the
same machine. Also this breaks communication with other machines because of
NDISC packet processing failure.
This patch fixes this issue by reading all interface's IPv6 addresses and adding
them to IPv6 routing table while bringing up 'lo'.
==Testing==
Before applying the patch:
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$ sudo ifdown lo
$ sudo ifup lo
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$
After applying the patch:
$ route -A inet6
Kernel IPv6 routing
table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$ sudo ifdown lo
$ sudo ifup lo
$ route -A inet6
Kernel IPv6 routing table
Destination Next Hop Flag Met Ref Use If
2000::20/128 :: U 256 0 0 eth0
fe80::/64 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
::1/128 :: Un 0 1 0 lo
2000::20/128 :: Un 0 1 0 lo
fe80::xxxx:xxxx:xxxx:xxxx/128 :: Un 0 1 0 lo
ff00::/8 :: U 256 0 0 eth0
::/0 :: !n -1 1 1 lo
$
Signed-off-by: Balakumaran Kannan <Balakumaran.Kannan@ap.sony.com>
Signed-off-by: Maruthi Thotad <Maruthi.Thotad@ap.sony.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3fb72f1e6e6165c5f495e8dc11c5bbd14c73385c ("ipconfig wait
for carrier") added a "wait for carrier on at least one interface"
policy, with a worst case maximum wait of two minutes.
However, if you encounter this, you won't get any feedback from
the console as to the nature of what is going on. You just see
the booting process hang for two minutes and then continue.
Here we add a message so the user knows what is going on, and
hence can take action to rectify the situation (e.g. fix network
cable or whatever.) After the 1st 10s pause, output now begins
that looks like this:
Waiting up to 110 more seconds for network.
Waiting up to 100 more seconds for network.
Waiting up to 90 more seconds for network.
Waiting up to 80 more seconds for network.
...
Since most systems will have no problem getting link/carrier in the
1st 10s, the only people who will see these messages are people with
genuine issues that need to be resolved.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
currently cbq works incorrectly for limits > 10% real link bandwidth,
and practically does not work for limits > 50% real link bandwidth.
Below are results of experiments taken on 1 Gbit link
In shaper | Actual Result
-----------+---------------
100M | 108 Mbps
200M | 244 Mbps
300M | 412 Mbps
500M | 893 Mbps
This happen because of q->now changes incorrectly in cbq_dequeue():
when it is called before real end of packet transmitting,
L2T is greater than real time delay, q_now gets an extra boost
but never compensate it.
To fix this problem we prevent change of q->now until its synchronization
with real time.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Reviewed-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 00cfec37484761 (net: add a synchronize_net() in
netdev_rx_handler_unregister())
allows us to remove the synchronized_net() call from del_nbp()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Because rev1 and rev3 of the target share the same hashing
generalize it by introduing nfqueue_hash().
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Current NFQUEUE target uses a hash, computed over source and
destination address (and other parameters), for steering the packet
to the actual NFQUEUE. This, however forgets about the fact that the
packet eventually is handled by a particular CPU on user request.
If E. g.
1) IRQ affinity is used to handle packets on a particular CPU already
(both single-queue or multi-queue case)
and/or
2) RPS is used to steer packets to a specific softirq
the target easily chooses an NFQUEUE which is not handled by a process
pinned to the same CPU.
The idea is therefore to use the CPU index for determining the
NFQUEUE handling the packet.
E. g. when having a system with 4 CPUs, 4 MQ queues and 4 NFQUEUEs it
looks like this:
+-----+ +-----+ +-----+ +-----+
|NFQ#0| |NFQ#1| |NFQ#2| |NFQ#3|
+-----+ +-----+ +-----+ +-----+
^ ^ ^ ^
| |NFQUEUE | |
+ + + +
+-----+ +-----+ +-----+ +-----+
|rx-0 | |rx-1 | |rx-2 | |rx-3 |
+-----+ +-----+ +-----+ +-----+
The NFQUEUEs not necessarily have to start with number 0, setups with
less NFQUEUEs than packet-handling CPUs are not a problem as well.
This patch extends the NFQUEUE target to accept a new
NFQ_FLAG_CPU_FANOUT flag. If this is specified the target uses the
CPU index for determining the NFQUEUE being used. I have to introduce
rev3 for this. The 'flags' are folded into _v2 'bypass'.
By changing the way which queue is assigned, I'm able to improve the
performance if the processes reading on the NFQUEUs are pinned
correctly.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We used a global BH disable in LOCAL_OUT hook.
Add _bh suffix to all places that need it and remove
the disabling from LOCAL_OUT and sync code.
Functions like ip_defrag need protection from
BH, so add it. As for nf_nat_mangle_tcp_packet, it needs
RCU lock.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
This is the final step in RCU conversion.
Things that are removed:
- svc->usecnt: now svc is accessed under RCU read lock
- svc->inc: and some unused code
- ip_vs_bind_pe and ip_vs_unbind_pe: no ability to replace PE
- __ip_vs_svc_lock: replaced with RCU
- IP_VS_WAIT_WHILE: now readers lookup svcs and dests under
RCU and work in parallel with configuration
Other changes:
- before now, a RCU read-side critical section included the
calling of the schedule method, now it is extended to include
service lookup
- ip_vs_svc_table and ip_vs_svc_fwm_table are now using hlist
- svc->pe and svc->scheduler remain to the end (of grace period),
the schedulers are prepared for such RCU readers
even after done_service is called but they need
to use synchronize_rcu because last ip_vs_scheduler_put
can happen while RCU read-side critical sections
use an outdated svc->scheduler pointer
- as planned, update_service is removed
- empty services can be freed immediately after grace period.
If dests were present, the services are freed from
the dest trash code
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
In previous commits the schedulers started to access
svc->destinations with _rcu list traversal primitives
because the IP_VS_WAIT_WHILE macro still plays the role of
grace period. Now it is time to finish the updating part,
i.e. adding and deleting of dests with _rcu suffix before
removing the IP_VS_WAIT_WHILE in next commit.
We use the same rule for conns as for the
schedulers: dests can be searched in RCU read-side critical
section where ip_vs_dest_hold can be called by ip_vs_bind_dest.
Some things are not perfect, for example, calling
functions like ip_vs_lookup_dest from updating code under
RCU, just because we use some function both from reader
and from updater.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
As all read_locks are gone spin lock is preferred.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
This method releases the scheduler state,
it can not fail. Such change will help to properly
replace the scheduler in following patch.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
All dests will go to trash, no exceptions.
But we have to use new list node t_list for this, due
to RCU changes in following patches. Dests will wait there
initial grace period and later all conns and schedulers to
put their reference. The dests don't get reference for
staying in dest trash as before.
As result, we do not load ip_vs_dest_put with
extra checks for last refcnt and the schedulers do not
need to play games with atomic_inc_not_zero while
selecting best destination.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The schedule method now needs _rcu list-traversal
primitive for svc->destinations. As the weight for some
dest can be reduced during dest selection, change the
algorithm to check weights by using minimum weights in the
1 .. max_weight-(di-1) range, with the same step (di). By this
way we ensure that there will be always a weight >= 1 check
before claiming that all destinations are overloaded.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The schedule method now needs _rcu list-traversal
primitive for svc->destinations.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Use the 3 new methods to reassign dests.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The schedule method now needs _rcu list-traversal
primitive for svc->destinations.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The schedule method now needs _rcu list-traversal
primitive for svc->destinations. As the previous entry
could be unlinked, limit the list traversals to 2 when
lookup started from previous entry.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The schedule method now needs _rcu list-traversal
primitive for svc->destinations.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The schedule method now needs _rcu list-traversal
primitive for svc->destinations.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The schedule method now needs _rcu list-traversal
primitive for svc->destinations. The read_lock for sched_lock is
removed. The set.lock is removed because now it is used in
rare cases, mostly under sched_lock.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The schedule method now needs _rcu list-traversal
primitive for svc->destinations. The read_lock for sched_lock is
removed. Use a dead flag to prevent new entries to be created
while scheduler is reclaimed. Use hlist for the hash table.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Use the new add_dest and del_dest methods
to reassign dests.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
ip_vs_dest_hold will be used under RCU lock
while ip_vs_dest_put can be called even after dest
is removed from service, as it happens for conns and
some schedulers.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Allow schedulers to use rcu_dereference when
returning destination on lookup. The RCU read-side critical
section will allow ip_vs_bind_dest to get dest refcnt as
preparation for the step where destinations will be
deleted without an IP_VS_WAIT_WHILE guard that holds the
packet processing during update.
Add new optional scheduler methods add_dest,
del_dest and upd_dest. For now the methods are called
together with update_service but update_service will be
removed in a following change.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The global list with schedulers ip_vs_schedulers
is accessed only from user context - configuration and
scheduler module [un]registration. Use ip_vs_sched_mutex
instead.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
We have many fields to set and few to reset,
use kmem_cache_alloc instead to save some cycles.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
__ip_vs_conn_in_get and ip_vs_conn_out_get are
hot places. Optimize them, so that ports are matched first.
By moving net and fwmark below, on 32-bit arch we can fit
caddr in 32-byte cache line and all addresses in 64-byte
cache line.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Convert __ip_vs_conntbl_lock_array as follows:
- readers that do not modify conn lists will use RCU lock
- updaters that modify lists will use spinlock_t
Now for conn lookups we will use RCU read-side
critical section. Without using __ip_vs_conn_get such
places have access to connection fields and can
dereference some pointers like pe and pe_data plus
the ability to update timer expiration. If full access
is required we contend for reference.
We add barrier in __ip_vs_conn_put, so that
other CPUs see the refcnt operation after other writes.
With the introduction of ip_vs_conn_unlink()
we try to reorganize ip_vs_conn_expire(), so that
unhashing of connections that should stay more time is
avoided, even if it is for very short time.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
Allow the readers to use RCU lock and for
PE module registrations use global mutex instead of
spinlock. All PE modules need to use synchronize_rcu
in their module exit handler.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off by: Hans Schillstrom <hans@schillstrom.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
