| Age | Commit message (Collapse) | Author |
|---|
|
Add flags intended to report various auxiliary information
and introduce the NL80211_RXMGMT_FLAG_ANSWERED flag to report
that the frame was already answered by the device.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
[REPLIED->ANSWERED, reword commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
According to 802.11-2012 9.3.2.10, paragraph 4, QoS
data frames with a group address in the Address 1 field
have sequence numbers allocated from the same counter
as non-QoS data and management frames. Without this
flag, some drivers may not assign sequence numbers, and
in rare cases frames might get dropped. Set the control
flag accordingly.
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Previously, the mesh STA responds to probe request from legacy STA
but now it will only respond to legacy STA if the legacy STA does include
the specific mesh ID or wildcard mesh ID in the probe request.
The iw patch "iw: scan using meshid" can be used either by legacy STA
or by mesh STA to do active scanning by inserting the mesh ID in the
probe request frame.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Acked-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
mac80211 currently sets WIPHY_FLAG_SUPPORTS_SCHED_SCAN based on whether
the start_sched_scan operation is supported or not, but that will not
be correct for all drivers, we're adding scheduled scan to the iwlmvm
driver but it depends on firmware support.
Therefore, move setting WIPHY_FLAG_SUPPORTS_SCHED_SCAN into the drivers
so that they can control it regardless of implementing the operation.
This currently only affects the TI drivers since they're the only ones
implementing scheduled scan (in a mac80211 driver.)
Acked-by: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We can simply use the %pISc format specifier that was recently added
and thus remove some code that distinguishes between IPv4 and IPv6.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rfc 4861 says the Redirected Header option is optional, so
the kernel should not drop the Redirect Message that has no
Redirected Header option. In this patch, the function
ip6_redirect_no_header() is introduced to deal with that
condition.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
|
|
The tcp_probe currently only supports analysis of IPv4 connections.
Therefore, it would be nice to have IPv6 supported as well. Since we
have the recently added %pISpc specifier that is IPv4/IPv6 generic,
build related sockaddress structures from the flow information and
pass this to our format string. Tested with SSH and HTTP sessions
on IPv4 and IPv6.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patches fixes a rather unproblematic function signature mismatch
as the const specifier was missing for the th variable; and next to
that it adds a build-time assertion so that future function signature
mismatches for kprobes will not end badly, similarly as commit 22222997
("net: sctp: add build check for sctp_sf_eat_sack_6_2/jsctp_sf_eat_sack")
did it for SCTP.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is helpful to sometimes know the TCP window sizes of an established
socket e.g. to confirm that window scaling is working or to tweak the
window size to improve high-latency connections, etc etc. Currently the
TCP snooper only exports the send window size, but not the receive window
size. Therefore, also add the receive window size to the end of the
output line.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
1) Some constifications, from Mathias Krause.
2) Catch bugs if a hold timer is still active when xfrm_policy_destroy()
is called, from Fan Du.
3) Remove a redundant address family checking, from Fan Du.
4) Make xfrm_state timer monotonic to be independent of system clock changes,
from Fan Du.
5) Remove an outdated comment on returning -EREMOTE in the xfrm_lookup(),
from Rami Rosen.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The stack currently detects reordering and avoid spurious
retransmission very well. However the throughput is sub-optimal under
high reordering because cwnd is increased only if the data is deliverd
in order. I.e., FLAG_DATA_ACKED check in tcp_ack(). The more packet
are reordered the worse the throughput is.
Therefore when reordering is proven high, cwnd should advance whenever
the data is delivered regardless of its ordering. If reordering is low,
conservatively advance cwnd only on ordered deliveries in Open state,
and retain cwnd in Disordered state (RFC5681).
Using netperf on a qdisc setup of 20Mbps BW and random RTT from 45ms
to 55ms (for reordering effect). This change increases TCP throughput
by 20 - 25% to near bottleneck BW.
A special case is the stretched ACK with new SACK and/or ECE mark.
For example, a receiver may receive an out of order or ECN packet with
unacked data buffered because of LRO or delayed ACK. The principle on
such an ACK is to advance cwnd on the cummulative acked part first,
then reduce cwnd in tcp_fastretrans_alert().
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 58ad436fcf49810aa006016107f494c9ac9013db.
It turns out that the change introduced a potential deadlock
by causing a locking dependency with netlink's cb_mutex. I
can't seem to find a way to resolve this without doing major
changes to the locking, so revert this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
|
|
Sujith reports that my commit af61a165187bb94b1dc7628ef815c23d0eacf40b
("mac80211: add control port protocol TX control flag") broke ath9k
(aggregation). The reason is that I made minstrel_ht use the flag in
the TX status path, where it can have been overwritten by the driver.
Since we have no more space in info->flags, revert that part of the
change for now, until we can reshuffle the flags or so.
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When initiating a transparent eSCO connection, make use of T2 settings
at first try. T2 is the recommended settings from HFP 1.6 WideBand
Speech. Upon connection failure, try T1 settings.
When CVSD is requested and eSCO is supported, try to establish eSCO
connection using S3 settings. If it fails, fallback in sequence to S2,
S1, D1, D0 settings.
To know which setting should be used, conn->attempt is used. It
indicates the currently ongoing SCO connection attempt and can be used
as the index for the fallback settings table.
These setting and the fallback order are described in Bluetooth HFP 1.6
specification p. 101.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Synchronous Connection Complete event can return error "Connection
Rejected due to Limited resources (0x10)".
Handling this error is required for SCO connection fallback. This error
happens when the server tried to accept the connection but failed to
negotiate settings.
This error code has been verified experimentally by sending a T2 request
to a T1 only SCO listener.
Client dump follows :
< HCI Command (0x01|0x0028) plen 17 [hci0] 3.696064
Handle: 12
Transmit bandwidth: 8000
Receive bandwidth: 8000
Max latency: 13
Setting: 0x0003
Retransmission effort: Optimize for link quality (0x02)
Packet type: 0x0380
> HCI Event (0x0f) plen 4 [hci0] 3.697034
Setup Synchronous Connection (0x01|0x0028) ncmd 1
Status: Success (0x00)
> HCI Event (0x2c) plen 17 [hci0] 3.736059
Status: Connection Rejected due to Limited Resources (0x0d)
Handle: 0
Address: xx:xx:xx:xx:xx:AB (OUI 70-F3-95)
Link type: eSCO (0x02)
Transmission interval: 0x0c
Retransmission window: 0x06
RX packet length: 60
TX packet length: 60
Air mode: Transparent (0x03)
Server dump follows :
> HCI Event (0x04) plen 10 [hci0] 4.741513
Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D)
Class: 0x620100
Major class: Computer (desktop, notebook, PDA, organizers)
Minor class: Uncategorized, code for device not assigned
Networking (LAN, Ad hoc)
Audio (Speaker, Microphone, Headset)
Telephony (Cordless telephony, Modem, Headset)
Link type: eSCO (0x02)
< HCI Command (0x01|0x0029) plen 21 [hci0] 4.743269
Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D)
Transmit bandwidth: 8000
Receive bandwidth: 8000
Max latency: 13
Setting: 0x0003
Retransmission effort: Optimize for link quality (0x02)
Packet type: 0x03c1
> HCI Event (0x0f) plen 4 [hci0] 4.745517
Accept Synchronous Connection (0x01|0x0029) ncmd 1
Status: Success (0x00)
> HCI Event (0x2c) plen 17 [hci0] 4.749508
Status: Connection Rejected due to Limited Resources (0x0d)
Handle: 0
Address: xx:xx:xx:xx:xx:D9 (OUI 20-68-9D)
Link type: eSCO (0x02)
Transmission interval: 0x0c
Retransmission window: 0x06
RX packet length: 60
TX packet length: 60
Air mode: Transparent (0x03)
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Older Bluetooth devices may not support Setup Synchronous Connection or
SCO transparent data. This is indicated by the corresponding LMP feature
bits. It is not possible to know if the adapter support these features
before setting BT_VOICE option since the socket is not bound to an
adapter. An adapter can also be added after the socket is created. The
socket can be bound to an address before adapter is plugged in.
Thus, on a such adapters, if user request BT_VOICE_TRANSPARENT, outgoing
connections fail on connect() and returns -EOPNOTSUPP. Incoming
connections do not fail. However, they should only be allowed depending
on what was specified in Write_Voice_Settings command.
EOPNOTSUPP is choosen because connect() system call is failing after
selecting route but before any connection attempt.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
In order to establish a transparent SCO connection, the correct settings
must be specified in the Setup Synchronous Connection request. For that,
a setting field is added to ACL connection data to set up the desired
parameters. The patch also removes usage of hdev->voice_setting in CVSD
connection and makes use of T2 parameters for transparent data.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
When an incoming eSCO connection is requested, check the selected voice
setting and reply appropriately. Voice setting should have been
negotiated previously. For example, in case of HFP, the codec is
negotiated using AT commands on the RFCOMM channel. This patch only
changes replies for socket with deferred setup enabled.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
This patch extends the current Bluetooth socket options with BT_VOICE.
This is intended to choose voice data type at runtime. It only applies
to SCO sockets. Incoming connections shall be setup during deferred
setup. Outgoing connections shall be setup before connect(). The desired
setting is stored in the SCO socket info. This patch declares needed
members, modifies getsockopt() and setsockopt().
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
From Bluetooth Core v4.0 specification, 7.1.8 Accept Connection Request
Command "When accepting synchronous connection request, the Role
parameter is not used and will be ignored by the BR/EDR Controller."
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
hci_connect is a super function for connecting hci protocols. But the
voice_setting parameter (introduced in subsequent patches) is only
needed by SCO and security requirements are not needed for SCO channels.
Thus, it makes sense to have a separate function for SCO.
Signed-off-by: Frédéric Dalleau <frederic.dalleau@linux.intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
In rfcomm_tty_cleanup we purge the dlc->tx_queue which may contain
socket buffers referencing the tty_port and thus preventing the tty_port
destruction.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
The tty_port can be released in two cases: when we get a HUP in the
functions rfcomm_tty_hangup() and rfcomm_dev_state_change(). Or when the
user releases the device in rfcomm_release_dev().
In these cases we set the flag RFCOMM_TTY_RELEASED so that no other
function can get a reference to the tty_port.
The use of !test_and_set_bit(RFCOMM_TTY_RELEASED) ensures that the
'initial' tty_port reference is only dropped once.
The rfcomm_dev_del function is removed becase it isn't used anymore.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Implement .activate, .shutdown and .carrier_raised methods of tty_port
to manage the dlc, moving the code from rfcomm_tty_install() and
rfcomm_tty_cleanup() functions.
At the same time the tty .open()/.close() and .hangup() methods are
changed to use the tty_port helpers that properly call the
aforementioned tty_port methods.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
Move the tty_struct initialization from rfcomm_tty_open() to
rfcomm_tty_install() and do the same for the cleanup moving the code from
rfcomm_tty_close() to rfcomm_tty_cleanup().
Add also extra error handling in rfcomm_tty_install() because, unlike
.open()/.close(), .cleanup() is not called if .install() fails.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
The current code removes the device from the device list in several
places. Do it only in the destructor instead and in the error path of
rfcomm_add_dev() if the device couldn't be initialized.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
In net/bluetooth/rfcomm/tty.c the struct tty_struct is used without
taking references. This may lead to a use-after-free of the rfcomm tty.
Fix this by taking references properly, using the tty_port_* helpers
when possible.
The raw assignments of dev->port.tty in rfcomm_tty_open/close are
addressed in the later commit 'rfcomm: Implement .activate, .shutdown
and .carrier_raised methods'.
Signed-off-by: Gianluca Anzolin <gianluca@sottospazio.it>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
In case of a Low Energy only controller it makes no sense to configure
the full BR/EDR event mask. It will just enable events that can not be
send anyway and there is no guarantee that such a controller will accept
this value.
Use event mask 0x90 0xe8 0x04 0x02 0x00 0x80 0x00 0x20 for LE-only
controllers which enables the following events:
Disconnection Complete
Encryption Change
Read Remote Version Information Complete
Command Complete
Command Status
Hardware Error
Number of Completed Packets
Data Buffer Overflow
Encryption Key Refresh Complete
LE Meta
This is according to Core Specification, Part E, Section 3.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
When a socket is in deferred state there does actually exist an
underlying connection even though the connection state is not yet
BT_CONNECTED. In the deferred state it should therefore be allowed to
get socket options that usually depend on a connection, such as
SCO_OPTIONS and SCO_CONNINFO.
This patch fixes the behavior of some user space code that behaves as
follows without it:
$ sudo tools/btiotest -i 00:1B:DC:xx:xx:xx -d -s
accept=2 reject=-1 discon=-1 defer=1 sec=0 update_sec=0 prio=0 voice=0x0000
Listening for SCO connections
bt_io_get(OPT_DEST): getsockopt(SCO_OPTIONS): Transport endpoint is not connected (107)
Accepting connection
Successfully connected to 60:D8:19:xx:xx:xx. handle=43, class=000000
The conditions that the patch updates the if-statements to is taken from
similar code in l2cap_sock.c which correctly handles the deferred state.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
my earlier patch "mac80211: change IBSS channel state to chandef"
created a regression by ignoring the channel parameter in
__ieee80211_sta_join_ibss, which breaks IBSS channel selection. This
patch fixes this situation by using the right channel and adopting the
selected bandwidth mode.
Cc: stable@vger.kernel.org
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
brcm80211 cannot handle sending frames with CCK rates as part of an
A-MPDU session. Other drivers may have issues too. Set the flag in all
drivers that have been tested with CCK rates.
This fixes a reported brcmsmac regression introduced in
commit ef47a5e4f1aaf1d0e2e6875e34b2c9595897bef6
"mac80211/minstrel_ht: fix cck rate sampling"
Cc: stable@vger.kernel.org # 3.10
Reported-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
IBSS needs to release the channel context when leaving
but I evidently missed that. Fix it.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of hard-coding length values, use a define to make it clear
where those lengths come from.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the functions mld_gq_start_timer(), mld_ifc_start_timer(),
and mld_dad_start_timer(), rather use unsigned long than int
as we operate only on unsigned values anyway. This seems more
appropriate as there is no good reason to do type conversions
to int, that could lead to future errors.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use proper API functions to calculate jiffies from milliseconds and
not the crude method of dividing HZ by a value. This ensures more
accurate values even in the case of strange HZ values. While at it,
also simplify code in the mlh2 case by using max().
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an Xin6 tunnel is set up, we check other netdevices to inherit the link-
local address. If none is available, the interface will not have any link-local
address. RFC4862 expects that each interface has a link local address.
Now than this kind of tunnels supports x-netns, it's easy to fall in this case
(by creating the tunnel in a netns where ethernet interfaces stand and then
moving it to a other netns where no ethernet interface is available).
RFC4291, Appendix A suggests two methods: the first is the one currently
implemented, the second is to generate a unique identifier, so that we can
always generate the link-local address. Let's use eth_random_addr() to generate
this interface indentifier.
I remove completly the previous method, hence for the whole life of the
interface, the link-local address remains the same (previously, it depends on
which ethernet interfaces were up when the tunnel interface was set up).
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit df8372ca747f6da9e8590775721d9363c1dfc87e.
These changes are buggy and make unintended semantic changes
to ip6_tnl_add_linklocal().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The VLAN code needs to know the length of the per-port VLAN bitmap to
perform its most basic operations (retrieving VLAN informations, removing
VLANs, forwarding database manipulation, etc). Unfortunately, in the
current implementation we are using a macro that indicates the bitmap
size in longs in places where the size in bits is expected, which in
some cases can cause what appear to be random failures.
Use the correct macro.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
Regarding the iwlwifi bits, Johannes says:
"We revert an rfkill bugfix that unfortunately caused more bugs, shuffle
some code to avoid touching the PCIe device before it's enabled and
disconnect if firmware fails to do our bidding. I also have Stanislaw's
fix to not crash in some channel switch scenarios."
As for the mac80211 bits, Johannes says:
"This time, I have one fix from Dan Carpenter for users of
nl80211hdr_put(), and one fix from myself fixing a regression with the
libertas driver."
Along with the above...
Dan Carpenter fixes some incorrectly placed "address of" operators
in hostap that caused copying of junk data.
Jussi Kivilinna corrects zd1201 to use an allocated buffer rather
than the stack for a URB operation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
getsockopt PACKET_STATISTICS returns tp_packets + tp_drops. Commit
ee80fbf301 ("packet: account statistics only in tpacket_stats_u")
cleaned up the getsockopt PACKET_STATISTICS code.
This also changed semantics. Historically, tp_packets included
tp_drops on return. The commit removed the line that adds tp_drops
into tp_packets.
This patch reinstates the old semantics.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Included change:
- Check if the skb has been correctly prepared before going on
|
|
We need to move the derefernce after the IS_ERR() check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As discussed last year [1], there is no compelling reason
to limit IPv4 MTU to 0xFFF0, while real limit is 0xFFFF
[1] : http://marc.info/?l=linux-netdev&m=135607247609434&w=2
Willem raised this issue again because some of our internal
regression tests broke after lo mtu being set to 65536.
IP_MTU reports 0xFFF0, and the test attempts to send a RAW datagram of
mtu + 1 bytes, expecting the send() to fail, but it does not.
Alexey raised interesting points about TCP MSS, that should be addressed
in follow-up patches in TCP stack if needed, as someone could also set
an odd mtu anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nocache-argument was used in tcp_v4_send_synack as an argument to
inet_csk_route_req. However, since ba3f7f04ef2b (ipv4: Kill
FLOWI_FLAG_RT_NOCACHE and associated code.) this is no more used.
This patch removes the unsued argument from tcp_v4_send_synack.
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ERROR: code indent should use tabs where possible: fix 2.
ERROR: do not use assignment in if condition: fix 5.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just follow the Joe Perches's opinion, it is a better way to fix the
style errors.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next
Conflicts:
net/netfilter/nf_conntrack_proto_tcp.c
The conflict had to do with overlapping changes dealing with
fixing the use of an "s32" to hold the value returned by
NAT_OFFSET().
Pablo Neira Ayuso says:
====================
The following batch contains Netfilter/IPVS updates for your net-next tree.
More specifically, they are:
* Trivial typo fix in xt_addrtype, from Phil Oester.
* Remove net_ratelimit in the conntrack logging for consistency with other
logging subsystem, from Patrick McHardy.
* Remove unneeded includes from the recently added xt_connlabel support, from
Florian Westphal.
* Allow to update conntracks via nfqueue, don't need NFQA_CFG_F_CONNTRACK for
this, from Florian Westphal.
* Remove tproxy core, now that we have socket early demux, from Florian
Westphal.
* A couple of patches to refactor conntrack event reporting to save a good
bunch of lines, from Florian Westphal.
* Fix missing locking in NAT sequence adjustment, it did not manifested in
any known bug so far, from Patrick McHardy.
* Change sequence number adjustment variable to 32 bits, to delay the
possible early overflow in long standing connections, also from Patrick.
* Comestic cleanups for IPVS, from Dragos Foianu.
* Fix possible null dereference in IPVS in the SH scheduler, from Daniel
Borkmann.
* Allow to attach conntrack expectations via nfqueue. Before this patch, you
had to use ctnetlink instead, thus, we save the conntrack lookup.
* Export xt_rpfilter and xt_HMARK header files, from Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Handle context based address when an unspecified address is given.
For other context based address we print a warning and drop the packet
because we don't support it right now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Werner Almesberger <werner@almesberger.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
