| Age | Commit message (Collapse) | Author |
|---|
|
Pull workqueue changes from Tejun Heo:
"PREPARE_[DELAYED_]WORK() were used to change the work function of work
items without fully reinitializing it; however, this makes workqueue
consider the work item as a different one from before and allows the
work item to start executing before the previous instance is finished
which can lead to extremely subtle issues which are painful to debug.
The interface has never been popular. This pull request contains
patches to remove existing usages and kill the interface. As one of
the changes was routed during the last devel cycle and another
depended on a pending change in nvme, for-3.15 contains a couple merge
commits.
In addition, interfaces which were deprecated quite a while ago -
__cancel_delayed_work() and WQ_NON_REENTRANT - are removed too"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
workqueue: remove deprecated WQ_NON_REENTRANT
workqueue: Spelling s/instensive/intensive/
workqueue: remove PREPARE_[DELAYED_]WORK()
staging/fwserial: don't use PREPARE_WORK
afs: don't use PREPARE_WORK
nvme: don't use PREPARE_WORK
usb: don't use PREPARE_DELAYED_WORK
floppy: don't use PREPARE_[DELAYED_]WORK
ps3-vuart: don't use PREPARE_WORK
wireless/rt2x00: don't use PREPARE_WORK in rt2800usb.c
workqueue: Remove deprecated __cancel_delayed_work()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 compat wrapper rework from Heiko Carstens:
"S390 compat system call wrapper simplification work.
The intention of this work is to get rid of all hand written assembly
compat system call wrappers on s390, which perform proper sign or zero
extension, or pointer conversion of compat system call parameters.
Instead all of this should be done with C code eg by using Al's
COMPAT_SYSCALL_DEFINEx() macro.
Therefore all common code and s390 specific compat system calls have
been converted to the COMPAT_SYSCALL_DEFINEx() macro.
In order to generate correct code all compat system calls may only
have eg compat_ulong_t parameters, but no unsigned long parameters.
Those patches which change parameter types from unsigned long to
compat_ulong_t parameters are separate in this series, but shouldn't
cause any harm.
The only compat system calls which intentionally have 64 bit
parameters (preadv64 and pwritev64) in support of the x86/32 ABI
haven't been changed, but are now only available if an architecture
defines __ARCH_WANT_COMPAT_SYS_PREADV64/PWRITEV64.
System calls which do not have a compat variant but still need proper
zero extension on s390, like eg "long sys_brk(unsigned long brk)" will
get a proper wrapper function with the new s390 specific
COMPAT_SYSCALL_WRAPx() macro:
COMPAT_SYSCALL_WRAP1(brk, unsigned long, brk);
which generates the following code (simplified):
asmlinkage long sys_brk(unsigned long brk);
asmlinkage long compat_sys_brk(long brk)
{
return sys_brk((u32)brk);
}
Given that the C file which contains all the COMPAT_SYSCALL_WRAP lines
includes both linux/syscall.h and linux/compat.h, it will generate
build errors, if the declaration of sys_brk() doesn't match, or if
there exists a non-matching compat_sys_brk() declaration.
In addition this will intentionally result in a link error if
somewhere else a compat_sys_brk() function exists, which probably
should have been used instead. Two more BUILD_BUG_ONs make sure the
size and type of each compat syscall parameter can be handled
correctly with the s390 specific macros.
I converted the compat system calls step by step to verify the
generated code is correct and matches the previous code. In fact it
did not always match, however that was always a bug in the hand
written asm code.
In result we get less code, less bugs, and much more sanity checking"
* 'compat' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (44 commits)
s390/compat: add copyright statement
compat: include linux/unistd.h within linux/compat.h
s390/compat: get rid of compat wrapper assembly code
s390/compat: build error for large compat syscall args
mm/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
kexec/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
net/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
ipc/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
fs/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
ipc/compat: convert to COMPAT_SYSCALL_DEFINE
fs/compat: convert to COMPAT_SYSCALL_DEFINE
security/compat: convert to COMPAT_SYSCALL_DEFINE
mm/compat: convert to COMPAT_SYSCALL_DEFINE
net/compat: convert to COMPAT_SYSCALL_DEFINE
kernel/compat: convert to COMPAT_SYSCALL_DEFINE
fs/compat: optional preadv64/pwrite64 compat system calls
ipc/compat_sys_msgrcv: change msgtyp type from long to compat_long_t
s390/compat: partial parameter conversion within syscall wrappers
s390/compat: automatic zero, sign and pointer conversion of syscalls
s390/compat: add sync_file_range and fallocate compat syscalls
...
|
|
Tejun Heo has made WQ_NON_REENTRANT useless in the dbf2576e37
("workqueue: make all workqueues non-reentrant"). So remove its
usages and definition.
This patch doesn't introduce any behavior changes.
tj: minor description updates.
Signed-off-by: ZhangZhen <zhenzhang.zhang@huawei.com>
Sigend-off-by: Tejun Heo <tj@kernel.org>
Acked-by: James Chapman <jchapman@katalix.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some drivers incorrectly assign vlan acceleration features to
vlan_features thus causing issues for Q-in-Q vlan configurations.
Warn the user of such cases.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the vlan filtering is enabled on the bridge, but
the filter is not configured on the bridge device itself,
running tcpdump on the bridge device will result in a
an Oops with NULL pointer dereference. The reason
is that br_pass_frame_up() will bypass the vlan
check because promisc flag is set. It will then try
to get the table pointer and process the packet based
on the table. Since the table pointer is NULL, we oops.
Catch this special condition in br_handle_vlan().
Reported-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
CC: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_network_protocol() already accounts for multiple vlan
headers that may be present in the skb. However, skb_mac_gso_segment()
doesn't know anything about it and assumes that skb->mac_len
is set correctly to skip all mac headers. That may not
always be the case. If we are simply forwarding the packet (via
bridge or macvtap), all vlan headers may not be accounted for.
A simple solution is to allow skb_network_protocol to return
the vlan depth it has calculated. This way skb_mac_gso_segment
will correctly skip all mac headers.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
addrconf_join_solict and addrconf_join_anycast may cause actions which
need rtnl locked, especially on first address creation.
A new DAD state is introduced which defers processing of the initial
DAD processing into a workqueue.
To get rtnl lock we need to push the code paths which depend on those
calls up to workqueues, specifically addrconf_verify and the DAD
processing.
(v2)
addrconf_dad_failure needs to be queued up to the workqueue, too. This
patch introduces a new DAD state and stop the DAD processing in the
workqueue (this is because of the possible ipv6_del_addr processing
which removes the solicited multicast address from the device).
addrconf_verify_lock is removed, too. After the transition it is not
needed any more.
As we are not processing in bottom half anymore we need to be a bit more
careful about disabling bottom half out when we lock spin_locks which are also
used in bh.
Relevant backtrace:
[ 541.030090] RTNL: assertion failed at net/core/dev.c (4496)
[ 541.031143] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 3.10.33-1-amd64-vyatta #1
[ 541.031145] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 541.031146] ffffffff8148a9f0 000000000000002f ffffffff813c98c1 ffff88007c4451f8
[ 541.031148] 0000000000000000 0000000000000000 ffffffff813d3540 ffff88007fc03d18
[ 541.031150] 0000880000000006 ffff88007c445000 ffffffffa0194160 0000000000000000
[ 541.031152] Call Trace:
[ 541.031153] <IRQ> [<ffffffff8148a9f0>] ? dump_stack+0xd/0x17
[ 541.031180] [<ffffffff813c98c1>] ? __dev_set_promiscuity+0x101/0x180
[ 541.031183] [<ffffffff813d3540>] ? __hw_addr_create_ex+0x60/0xc0
[ 541.031185] [<ffffffff813cfe1a>] ? __dev_set_rx_mode+0xaa/0xc0
[ 541.031189] [<ffffffff813d3a81>] ? __dev_mc_add+0x61/0x90
[ 541.031198] [<ffffffffa01dcf9c>] ? igmp6_group_added+0xfc/0x1a0 [ipv6]
[ 541.031208] [<ffffffff8111237b>] ? kmem_cache_alloc+0xcb/0xd0
[ 541.031212] [<ffffffffa01ddcd7>] ? ipv6_dev_mc_inc+0x267/0x300 [ipv6]
[ 541.031216] [<ffffffffa01c2fae>] ? addrconf_join_solict+0x2e/0x40 [ipv6]
[ 541.031219] [<ffffffffa01ba2e9>] ? ipv6_dev_ac_inc+0x159/0x1f0 [ipv6]
[ 541.031223] [<ffffffffa01c0772>] ? addrconf_join_anycast+0x92/0xa0 [ipv6]
[ 541.031226] [<ffffffffa01c311e>] ? __ipv6_ifa_notify+0x11e/0x1e0 [ipv6]
[ 541.031229] [<ffffffffa01c3213>] ? ipv6_ifa_notify+0x33/0x50 [ipv6]
[ 541.031233] [<ffffffffa01c36c8>] ? addrconf_dad_completed+0x28/0x100 [ipv6]
[ 541.031241] [<ffffffff81075c1d>] ? task_cputime+0x2d/0x50
[ 541.031244] [<ffffffffa01c38d6>] ? addrconf_dad_timer+0x136/0x150 [ipv6]
[ 541.031247] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
[ 541.031255] [<ffffffff8105313a>] ? call_timer_fn.isra.22+0x2a/0x90
[ 541.031258] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
Hunks and backtrace stolen from a patch by Stephen Hemminger.
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems I missed one change in get_timewait4_sock() to compute
the remaining time before deletion of IPV4 timewait socket.
This could result in wrong output in /proc/net/tcp for tm->when field.
Fixes: 96f817fedec4 ("tcp: shrink tcp6_timewait_sock by one cache line")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are two problematic situations.
A deadlock can happen when is_percpu is false because it can get
interrupted while holding the spinlock. Then it executes
ovs_flow_stats_update() in softirq context which tries to get
the same lock.
The second sitation is that when is_percpu is true, the code
correctly disables BH but only for the local CPU, so the
following can happen when locking the remote CPU without
disabling BH:
CPU#0 CPU#1
ovs_flow_stats_get()
stats_read()
+->spin_lock remote CPU#1 ovs_flow_stats_get()
| <interrupted> stats_read()
| ... +--> spin_lock remote CPU#0
| | <interrupted>
| ovs_flow_stats_update() | ...
| spin_lock local CPU#0 <--+ ovs_flow_stats_update()
+---------------------------------- spin_lock local CPU#1
This patch disables BH for both cases fixing the deadlocks.
Acked-by: Jesse Gross <jesse@nicira.com>
=================================
[ INFO: inconsistent lock state ]
3.14.0-rc8-00007-g632b06a #1 Tainted: G I
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/0/0 [HC0[0]:SC1[5]:HE1:SE0] takes:
(&(&cpu_stats->lock)->rlock){+.?...}, at: [<ffffffffa05dd8a1>] ovs_flow_stats_update+0x51/0xd0 [openvswitch]
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff810f973f>] __lock_acquire+0x68f/0x1c40
[<ffffffff810fb4e2>] lock_acquire+0xa2/0x1d0
[<ffffffff817d8d9e>] _raw_spin_lock+0x3e/0x80
[<ffffffffa05dd9e4>] ovs_flow_stats_get+0xc4/0x1e0 [openvswitch]
[<ffffffffa05da855>] ovs_flow_cmd_fill_info+0x185/0x360 [openvswitch]
[<ffffffffa05daf05>] ovs_flow_cmd_build_info.constprop.27+0x55/0x90 [openvswitch]
[<ffffffffa05db41d>] ovs_flow_cmd_new_or_set+0x4dd/0x570 [openvswitch]
[<ffffffff816c245d>] genl_family_rcv_msg+0x1cd/0x3f0
[<ffffffff816c270e>] genl_rcv_msg+0x8e/0xd0
[<ffffffff816c0239>] netlink_rcv_skb+0xa9/0xc0
[<ffffffff816c0798>] genl_rcv+0x28/0x40
[<ffffffff816bf830>] netlink_unicast+0x100/0x1e0
[<ffffffff816bfc57>] netlink_sendmsg+0x347/0x770
[<ffffffff81668e9c>] sock_sendmsg+0x9c/0xe0
[<ffffffff816692d9>] ___sys_sendmsg+0x3a9/0x3c0
[<ffffffff8166a911>] __sys_sendmsg+0x51/0x90
[<ffffffff8166a962>] SyS_sendmsg+0x12/0x20
[<ffffffff817e3ce9>] system_call_fastpath+0x16/0x1b
irq event stamp: 1740726
hardirqs last enabled at (1740726): [<ffffffff8175d5e0>] ip6_finish_output2+0x4f0/0x840
hardirqs last disabled at (1740725): [<ffffffff8175d59b>] ip6_finish_output2+0x4ab/0x840
softirqs last enabled at (1740674): [<ffffffff8109be12>] _local_bh_enable+0x22/0x50
softirqs last disabled at (1740675): [<ffffffff8109db05>] irq_exit+0xc5/0xd0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&cpu_stats->lock)->rlock);
<Interrupt>
lock(&(&cpu_stats->lock)->rlock);
*** DEADLOCK ***
5 locks held by swapper/0/0:
#0: (((&ifa->dad_timer))){+.-...}, at: [<ffffffff810a7155>] call_timer_fn+0x5/0x320
#1: (rcu_read_lock){.+.+..}, at: [<ffffffff81788a55>] mld_sendpack+0x5/0x4a0
#2: (rcu_read_lock_bh){.+....}, at: [<ffffffff8175d149>] ip6_finish_output2+0x59/0x840
#3: (rcu_read_lock_bh){.+....}, at: [<ffffffff8168ba75>] __dev_queue_xmit+0x5/0x9b0
#4: (rcu_read_lock){.+.+..}, at: [<ffffffffa05e41b5>] internal_dev_xmit+0x5/0x110 [openvswitch]
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G I 3.14.0-rc8-00007-g632b06a #1
Hardware name: /DX58SO, BIOS SOX5810J.86A.5599.2012.0529.2218 05/29/2012
0000000000000000 0fcf20709903df0c ffff88042d603808 ffffffff817cfe3c
ffffffff81c134c0 ffff88042d603858 ffffffff817cb6da 0000000000000005
ffffffff00000001 ffff880400000000 0000000000000006 ffffffff81c134c0
Call Trace:
<IRQ> [<ffffffff817cfe3c>] dump_stack+0x4d/0x66
[<ffffffff817cb6da>] print_usage_bug+0x1f4/0x205
[<ffffffff810f7f10>] ? check_usage_backwards+0x180/0x180
[<ffffffff810f8963>] mark_lock+0x223/0x2b0
[<ffffffff810f96d3>] __lock_acquire+0x623/0x1c40
[<ffffffff810f5707>] ? __lock_is_held+0x57/0x80
[<ffffffffa05e26c6>] ? masked_flow_lookup+0x236/0x250 [openvswitch]
[<ffffffff810fb4e2>] lock_acquire+0xa2/0x1d0
[<ffffffffa05dd8a1>] ? ovs_flow_stats_update+0x51/0xd0 [openvswitch]
[<ffffffff817d8d9e>] _raw_spin_lock+0x3e/0x80
[<ffffffffa05dd8a1>] ? ovs_flow_stats_update+0x51/0xd0 [openvswitch]
[<ffffffffa05dd8a1>] ovs_flow_stats_update+0x51/0xd0 [openvswitch]
[<ffffffffa05dcc64>] ovs_dp_process_received_packet+0x84/0x120 [openvswitch]
[<ffffffff810f93f7>] ? __lock_acquire+0x347/0x1c40
[<ffffffffa05e3bea>] ovs_vport_receive+0x2a/0x30 [openvswitch]
[<ffffffffa05e4218>] internal_dev_xmit+0x68/0x110 [openvswitch]
[<ffffffffa05e41b5>] ? internal_dev_xmit+0x5/0x110 [openvswitch]
[<ffffffff8168b4a6>] dev_hard_start_xmit+0x2e6/0x8b0
[<ffffffff8168be87>] __dev_queue_xmit+0x417/0x9b0
[<ffffffff8168ba75>] ? __dev_queue_xmit+0x5/0x9b0
[<ffffffff8175d5e0>] ? ip6_finish_output2+0x4f0/0x840
[<ffffffff8168c430>] dev_queue_xmit+0x10/0x20
[<ffffffff8175d641>] ip6_finish_output2+0x551/0x840
[<ffffffff8176128a>] ? ip6_finish_output+0x9a/0x220
[<ffffffff8176128a>] ip6_finish_output+0x9a/0x220
[<ffffffff8176145f>] ip6_output+0x4f/0x1f0
[<ffffffff81788c29>] mld_sendpack+0x1d9/0x4a0
[<ffffffff817895b8>] mld_send_initial_cr.part.32+0x88/0xa0
[<ffffffff817691b0>] ? addrconf_dad_completed+0x220/0x220
[<ffffffff8178e301>] ipv6_mc_dad_complete+0x31/0x50
[<ffffffff817690d7>] addrconf_dad_completed+0x147/0x220
[<ffffffff817691b0>] ? addrconf_dad_completed+0x220/0x220
[<ffffffff8176934f>] addrconf_dad_timer+0x19f/0x1c0
[<ffffffff810a71e9>] call_timer_fn+0x99/0x320
[<ffffffff810a7155>] ? call_timer_fn+0x5/0x320
[<ffffffff817691b0>] ? addrconf_dad_completed+0x220/0x220
[<ffffffff810a76c4>] run_timer_softirq+0x254/0x3b0
[<ffffffff8109d47d>] __do_softirq+0x12d/0x480
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a bridge with vlan_filtering enabled receives frames with stacked
vlan tags, i.e., they have two vlan tags, br_vlan_untag() strips not
only the outer tag but also the inner tag.
br_vlan_untag() is called only from br_handle_vlan(), and in this case,
it is enough to set skb->vlan_tci to 0 here, because vlan_tci has already
been set before calling br_handle_vlan().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bridge vlan code (br_vlan_get_tag()) assumes that all frames have vlan_tci
if they are tagged, but if vlan tx offload is manually disabled on bridge
device and frames are sent from vlan device on the bridge device, the tags
are embedded in skb->data and they break this assumption.
Extract embedded vlan tags and move them to vlan_tci at ingress.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_zerocopy can copy elements of the frags array between skbs, but it doesn't
orphan them. Also, it doesn't handle errors, so this patch takes care of that
as well, and modify the callers accordingly. skb_tx_error() is also added to
the callers so they will signal the failed delivery towards the creator of the
skb.
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, if the card supports CTAG acceleration we do not
account for the vlan header even if we are configuring an
8021AD vlan. This may not be best since we'll do software
tagging for 8021AD which will cause data copy on skb head expansion
Configure the length based on available hw offload capabilities and
vlan protocol.
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some applications didn't expect recvmsg() on a non blocking socket
could return -EINTR. This possibility was added as a side effect
of commit b3ca9b02b00704 ("net: fix multithreaded signal handling in
unix recv routines").
To hit this bug, you need to be a bit unlucky, as the u->readlock
mutex is usually held for very small periods.
Fixes: b3ca9b02b00704 ("net: fix multithreaded signal handling in unix recv routines")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rainer Weikusat <rweikusat@mobileactivedefense.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 10ddceb22ba (ip_tunnel:multicast process cause panic due
to skb->_skb_refdst NULL pointer) removed dst-drop call from
ip-tunnel-recv.
Following commit reintroduce dst-drop and fix the original bug by
checking loopback packet before releasing dst.
Original bug: https://bugzilla.kernel.org/show_bug.cgi?id=70681
CC: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a topology event subscription fails for any reason, such as out
of memory, max number reached or because we received an invalid
request the correct behavior is to terminate the subscribers
connection to the topology server. This is currently broken and
produces the following oops:
[27.953662] tipc: Subscription rejected, illegal request
[27.955329] BUG: spinlock recursion on CPU#1, kworker/u4:0/6
[27.957066] lock: 0xffff88003c67f408, .magic: dead4ead, .owner: kworker/u4:0/6, .owner_cpu: 1
[27.958054] CPU: 1 PID: 6 Comm: kworker/u4:0 Not tainted 3.14.0-rc6+ #5
[27.960230] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[27.960874] Workqueue: tipc_rcv tipc_recv_work [tipc]
[27.961430] ffff88003c67f408 ffff88003de27c18 ffffffff815c0207 ffff88003de1c050
[27.962292] ffff88003de27c38 ffffffff815beec5 ffff88003c67f408 ffffffff817f0a8a
[27.963152] ffff88003de27c58 ffffffff815beeeb ffff88003c67f408 ffffffffa0013520
[27.964023] Call Trace:
[27.964292] [<ffffffff815c0207>] dump_stack+0x45/0x56
[27.964874] [<ffffffff815beec5>] spin_dump+0x8c/0x91
[27.965420] [<ffffffff815beeeb>] spin_bug+0x21/0x26
[27.965995] [<ffffffff81083df6>] do_raw_spin_lock+0x116/0x140
[27.966631] [<ffffffff815c6215>] _raw_spin_lock_bh+0x15/0x20
[27.967256] [<ffffffffa0008540>] subscr_conn_shutdown_event+0x20/0xa0 [tipc]
[27.968051] [<ffffffffa000fde4>] tipc_close_conn+0xa4/0xb0 [tipc]
[27.968722] [<ffffffffa00101ba>] tipc_conn_terminate+0x1a/0x30 [tipc]
[27.969436] [<ffffffffa00089a2>] subscr_conn_msg_event+0x1f2/0x2f0 [tipc]
[27.970209] [<ffffffffa0010000>] tipc_receive_from_sock+0x90/0xf0 [tipc]
[27.970972] [<ffffffffa000fa79>] tipc_recv_work+0x29/0x50 [tipc]
[27.971633] [<ffffffff8105dbf5>] process_one_work+0x165/0x3e0
[27.972267] [<ffffffff8105e869>] worker_thread+0x119/0x3a0
[27.972896] [<ffffffff8105e750>] ? manage_workers.isra.25+0x2a0/0x2a0
[27.973622] [<ffffffff810648af>] kthread+0xdf/0x100
[27.974168] [<ffffffff810647d0>] ? kthread_create_on_node+0x1a0/0x1a0
[27.974893] [<ffffffff815ce13c>] ret_from_fork+0x7c/0xb0
[27.975466] [<ffffffff810647d0>] ? kthread_create_on_node+0x1a0/0x1a0
The recursion occurs when subscr_terminate tries to grab the
subscriber lock, which is already taken by subscr_conn_msg_event.
We fix this by checking if the request to establish a new
subscription was successful, and if not we initiate termination of
the subscriber after we have released the subscriber lock.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Neighbor Solicitation is ipv6 protocol, so we should check
skb->protocol with ETH_P_IPV6
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Cc: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jesse/openvswitch
Jesse Gross says:
====================
Open vSwitch
Four small fixes for net/3.14. I realize that these are late in the
cycle - just got back from vacation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 812e44dd1829 ("ip6mr: advertise new mfc entries via rtnl") reuses the
function ip6mr_fill_mroute() to notify mfc events.
But this function was used only for dump and thus was always setting the
flag NLM_F_MULTI, which is wrong in case of a single notification.
Libraries like libnl will wait forever for NLMSG_DONE.
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 8cd3ac9f9b7b ("ipmr: advertise new mfc entries via rtnl") reuses the
function ipmr_fill_mroute() to notify mfc events.
But this function was used only for dump and thus was always setting the
flag NLM_F_MULTI, which is wrong in case of a single notification.
Libraries like libnl will wait forever for NLMSG_DONE.
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 3ff661c38c84 ("net: rtnetlink notify events for FDB NTF_SELF adds and
deletes") reuses the function nlmsg_populate_fdb_fill() to notify fdb events.
But this function was used only for dump and thus was always setting the
flag NLM_F_MULTI, which is wrong in case of a single notification.
Libraries like libnl will wait forever for NLMSG_DONE.
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The kernel starts out its "jiffies" timer as 5 minutes below zero, as
shown in include/linux/jiffies.h:
/*
* Have the 32 bit jiffies value wrap 5 minutes after boot
* so jiffies wrap bugs show up earlier.
*/
#define INITIAL_JIFFIES ((unsigned long)(unsigned int) (-300*HZ))
The loop in ovs_flow_stats_get() starts out with 'used' set to 0, then
takes any "later" time. This means that for the first five minutes after
boot, flows will always be reported as never used, since 0 is greater than
any time already seen.
Signed-off-by: Ben Pfaff <blp@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
|
|
In ip6_append_data_mtu(), when the xfrm mode is not tunnel(such as
transport),the ipsec header need to be added in the first fragment, so the mtu
will decrease to reserve space for it, then the second fragment come, the mtu
should be turn back, as the commit 0c1833797a5a6ec23ea9261d979aa18078720b74
said. however, in the commit a493e60ac4bbe2e977e7129d6d8cbb0dd236be, it use
*mtu = min(*mtu, ...) to change the mtu, which lead to the new mtu is alway
equal with the first fragment's. and cannot turn back.
when I test through ping6 -c1 -s5000 $ip (mtu=1280):
...frag (0|1232) ESP(spi=0x00002000,seq=0xb), length 1232
...frag (1232|1216)
...frag (2448|1216)
...frag (3664|1216)
...frag (4880|164)
which should be:
...frag (0|1232) ESP(spi=0x00001000,seq=0x1), length 1232
...frag (1232|1232)
...frag (2464|1232)
...frag (3696|1232)
...frag (4928|116)
so delete the min() when change back the mtu.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Fixes: 75a493e60ac4bb ("ipv6: ip6_append_data_mtu did not care about pmtudisc and frag_size")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
1) Fix a sleep in atomic when pfkey_sadb2xfrm_user_sec_ctx()
is called from pfkey_compile_policy().
Fix from Nikolay Aleksandrov.
2) security_xfrm_policy_alloc() can be called in process and atomic
context. Add an argument to let the callers choose the appropriate
way. Fix from Nikolay Aleksandrov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"I know this is a bit more than you want to see, and I've told the
wireless folks under no uncertain terms that they must severely scale
back the extent of the fixes they are submitting this late in the
game.
Anyways:
1) vmxnet3's netpoll doesn't perform the equivalent of an ISR, which
is the correct implementation, like it should. Instead it does
something like a NAPI poll operation. This leads to crashes.
From Neil Horman and Arnd Bergmann.
2) Segmentation of SKBs requires proper socket orphaning of the
fragments, otherwise we might access stale state released by the
release callbacks.
This is a 5 patch fix, but the initial patches are giving
variables and such significantly clearer names such that the
actual fix itself at the end looks trivial.
From Michael S. Tsirkin.
3) TCP control block release can deadlock if invoked from a timer on
an already "owned" socket. Fix from Eric Dumazet.
4) In the bridge multicast code, we must validate that the
destination address of general queries is the link local all-nodes
multicast address. From Linus Lüssing.
5) The x86 BPF JIT support for negative offsets puts the parameter
for the helper function call in the wrong register. Fix from
Alexei Starovoitov.
6) The descriptor type used for RTL_GIGA_MAC_VER_17 chips in the
r8169 driver is incorrect. Fix from Hayes Wang.
7) The xen-netback driver tests skb_shinfo(skb)->gso_type bits to see
if a packet is a GSO frame, but that's not the correct test. It
should use skb_is_gso(skb) instead. Fix from Wei Liu.
8) Negative msg->msg_namelen values should generate an error, from
Matthew Leach.
9) at86rf230 can deadlock because it takes the same lock from it's
ISR and it's hard_start_xmit method, without disabling interrupts
in the latter. Fix from Alexander Aring.
10) The FEC driver's restart doesn't perform operations in the correct
order, so promiscuous settings can get lost. Fix from Stefan
Wahren.
11) Fix SKB leak in SCTP cookie handling, from Daniel Borkmann.
12) Reference count and memory leak fixes in TIPC from Ying Xue and
Erik Hugne.
13) Forced eviction in inet_frag_evictor() must strictly make sure all
frags are deleted, otherwise module unload (f.e. 6lowpan) can
crash. Fix from Florian Westphal.
14) Remove assumptions in AF_UNIX's use of csum_partial() (which it
uses as a hash function), which breaks on PowerPC. From Anton
Blanchard.
The main gist of the issue is that csum_partial() is defined only
as a value that, once folded (f.e. via csum_fold()) produces a
correct 16-bit checksum. It is legitimate, therefore, for
csum_partial() to produce two different 32-bit values over the
same data if their respective alignments are different.
15) Fix endiannes bug in MAC address handling of ibmveth driver, also
from Anton Blanchard.
16) Error checks for ipv6 exthdrs offload registration are reversed,
from Anton Nayshtut.
17) Externally triggered ipv6 addrconf routes should count against the
garbage collection threshold. Fix from Sabrina Dubroca.
18) The PCI shutdown handler added to the bnx2 driver can wedge the
chip if it was not brought up earlier already, which in particular
causes the firmware to shut down the PHY. Fix from Michael Chan.
19) Adjust the sanity WARN_ON_ONCE() in qdisc_list_add() because as
currently coded it can and does trigger in legitimate situations.
From Eric Dumazet.
20) BNA driver fails to build on ARM because of a too large udelay()
call, fix from Ben Hutchings.
21) Fair-Queue qdisc holds locks during GFP_KERNEL allocations, fix
from Eric Dumazet.
22) The vlan passthrough ops added in the previous release causes a
regression in source MAC address setting of outgoing headers in
some circumstances. Fix from Peter Boström"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (70 commits)
ipv6: Avoid unnecessary temporary addresses being generated
eth: fec: Fix lost promiscuous mode after reconnecting cable
bonding: set correct vlan id for alb xmit path
at86rf230: fix lockdep splats
net/mlx4_en: Deregister multicast vxlan steering rules when going down
vmxnet3: fix building without CONFIG_PCI_MSI
MAINTAINERS: add networking selftests to NETWORKING
net: socket: error on a negative msg_namelen
MAINTAINERS: Add tools/net to NETWORKING [GENERAL]
packet: doc: Spelling s/than/that/
net/mlx4_core: Load the IB driver when the device supports IBoE
net/mlx4_en: Handle vxlan steering rules for mac address changes
net/mlx4_core: Fix wrong dump of the vxlan offloads device capability
xen-netback: use skb_is_gso in xenvif_start_xmit
r8169: fix the incorrect tx descriptor version
tools/net/Makefile: Define PACKAGE to fix build problems
x86: bpf_jit: support negative offsets
bridge: multicast: enable snooping on general queries only
bridge: multicast: add sanity check for general query destination
tcp: tcp_release_cb() should release socket ownership
...
|
|
tmp_prefered_lft is an offset to ifp->tstamp, not now. Therefore
age needs to be added to the condition.
Age calculation in ipv6_create_tempaddr is different from the one
in addrconf_verify and doesn't consider ADDRCONF_TIMER_FUZZ_MINUS.
This can cause age in ipv6_create_tempaddr to be less than the one
in addrconf_verify and therefore unnecessary temporary address to
be generated.
Use age calculation as in addrconf_modify to avoid this.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When copying in a struct msghdr from the user, if the user has set the
msg_namelen parameter to a negative value it gets clamped to a valid
size due to a comparison between signed and unsigned values.
Ensure the syscall errors when the user passes in a negative value.
Signed-off-by: Matthew Leach <matthew.leach@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this check someone could easily create a denial of service
by injecting multicast-specific queries to enable the bridge
snooping part if no real querier issuing periodic general queries
is present on the link which would result in the bridge wrongly
shutting down ports for multicast traffic as the bridge did not learn
about these listeners.
With this patch the snooping code is enabled upon receiving valid,
general queries only.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
General IGMP and MLD queries are supposed to have the multicast
link-local all-nodes address as their destination according to RFC2236
section 9, RFC3376 section 4.1.12/9.1, RFC2710 section 8 and RFC3810
section 5.1.15.
Without this check, such malformed IGMP/MLD queries can result in a
denial of service: The queries are ignored by most IGMP/MLD listeners
therefore they will not respond with an IGMP/MLD report. However,
without this patch these malformed MLD queries would enable the
snooping part in the bridge code, potentially shutting down the
according ports towards these hosts for multicast traffic as the
bridge did not learn about these listeners.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lars Persson reported following deadlock :
-000 |M:0x0:0x802B6AF8(asm) <-- arch_spin_lock
-001 |tcp_v4_rcv(skb = 0x8BD527A0) <-- sk = 0x8BE6B2A0
-002 |ip_local_deliver_finish(skb = 0x8BD527A0)
-003 |__netif_receive_skb_core(skb = 0x8BD527A0, ?)
-004 |netif_receive_skb(skb = 0x8BD527A0)
-005 |elk_poll(napi = 0x8C770500, budget = 64)
-006 |net_rx_action(?)
-007 |__do_softirq()
-008 |do_softirq()
-009 |local_bh_enable()
-010 |tcp_rcv_established(sk = 0x8BE6B2A0, skb = 0x87D3A9E0, th = 0x814EBE14, ?)
-011 |tcp_v4_do_rcv(sk = 0x8BE6B2A0, skb = 0x87D3A9E0)
-012 |tcp_delack_timer_handler(sk = 0x8BE6B2A0)
-013 |tcp_release_cb(sk = 0x8BE6B2A0)
-014 |release_sock(sk = 0x8BE6B2A0)
-015 |tcp_sendmsg(?, sk = 0x8BE6B2A0, ?, ?)
-016 |sock_sendmsg(sock = 0x8518C4C0, msg = 0x87D8DAA8, size = 4096)
-017 |kernel_sendmsg(?, ?, ?, ?, size = 4096)
-018 |smb_send_kvec()
-019 |smb_send_rqst(server = 0x87C4D400, rqst = 0x87D8DBA0)
-020 |cifs_call_async()
-021 |cifs_async_writev(wdata = 0x87FD6580)
-022 |cifs_writepages(mapping = 0x852096E4, wbc = 0x87D8DC88)
-023 |__writeback_single_inode(inode = 0x852095D0, wbc = 0x87D8DC88)
-024 |writeback_sb_inodes(sb = 0x87D6D800, wb = 0x87E4A9C0, work = 0x87D8DD88)
-025 |__writeback_inodes_wb(wb = 0x87E4A9C0, work = 0x87D8DD88)
-026 |wb_writeback(wb = 0x87E4A9C0, work = 0x87D8DD88)
-027 |wb_do_writeback(wb = 0x87E4A9C0, force_wait = 0)
-028 |bdi_writeback_workfn(work = 0x87E4A9CC)
-029 |process_one_work(worker = 0x8B045880, work = 0x87E4A9CC)
-030 |worker_thread(__worker = 0x8B045880)
-031 |kthread(_create = 0x87CADD90)
-032 |ret_from_kernel_thread(asm)
Bug occurs because __tcp_checksum_complete_user() enables BH, assuming
it is running from softirq context.
Lars trace involved a NIC without RX checksum support but other points
are problematic as well, like the prequeue stuff.
Problem is triggered by a timer, that found socket being owned by user.
tcp_release_cb() should call tcp_write_timer_handler() or
tcp_delack_timer_handler() in the appropriate context :
BH disabled and socket lock held, but 'owned' field cleared,
as if they were running from timer handlers.
Fixes: 6f458dfb4092 ("tcp: improve latencies of timer triggered events")
Reported-by: Lars Persson <lars.persson@axis.com>
Tested-by: Lars Persson <lars.persson@axis.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_segment copies frags around, so we need
to copy them carefully to avoid accessing
user memory after reporting completion to userspace
through a callback.
skb_segment doesn't normally happen on datapath:
TSO needs to be disabled - so disabling zero copy
in this case does not look like a big deal.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fskb is unrelated to frag: it's coming from
frag_list. Rename it list_skb to avoid confusion.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rename local variable to make it easier to tell at a glance that we are
dealing with a head skb.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_frag can in fact point at either skb
or fskb so rename it generally "frag".
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
frag points at nskb, so name it appropriately
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With TX VLAN offload enabled the source MAC address for frames sent using the
VLAN interface is currently set to the address of the real interface. This is
wrong since the VLAN interface may be configured with a different address.
The bug was introduced in commit 2205369a314e12fcec4781cc73ac9c08fc2b47de
("vlan: Fix header ops passthru when doing TX VLAN offload.").
This patch sets the source address before calling the create function of the
real interface.
Signed-off-by: Peter Boström <peter.bostrom@netrounds.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resizing fq hash table allocates memory while holding qdisc spinlock,
with BH disabled.
This is definitely not good, as allocation might sleep.
We can drop the lock and get it when needed, we hold RTNL so no other
changes can happen at the same time.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: afe4fd062416 ("pkt_sched: fq: Fair Queue packet scheduler")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro.
Clean up file table accesses (get rid of fget_light() in favor of the
fdget() interface), add proper file position locking.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
get rid of fget_light()
sockfd_lookup_light(): switch to fdget^W^Waway from fget_light
vfs: atomic f_pos accesses as per POSIX
ocfs2 syncs the wrong range...
|
|
The WARN_ON(root == &noop_qdisc)) added in qdisc_list_add()
can trigger in normal conditions when devices are not up.
It should be done only right before the list_add_tail() call.
Fixes: e57a784d8cae4 ("pkt_sched: set root qdisc before change() in attach_default_qdiscs()")
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Tested-by: Mirco Tischler <mt-ml@gmx.de>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
security_xfrm_policy_alloc can be called in atomic context so the
allocation should be done with GFP_ATOMIC. Add an argument to let the
callers choose the appropriate way. In order to do so a gfp argument
needs to be added to the method xfrm_policy_alloc_security in struct
security_operations and to the internal function
selinux_xfrm_alloc_user. After that switch to GFP_ATOMIC in the atomic
callers and leave GFP_KERNEL as before for the rest.
The path that needed the gfp argument addition is:
security_xfrm_policy_alloc -> security_ops.xfrm_policy_alloc_security ->
all users of xfrm_policy_alloc_security (e.g. selinux_xfrm_policy_alloc) ->
selinux_xfrm_alloc_user (here the allocation used to be GFP_KERNEL only)
Now adding a gfp argument to selinux_xfrm_alloc_user requires us to also
add it to security_context_to_sid which is used inside and prior to this
patch did only GFP_KERNEL allocation. So add gfp argument to
security_context_to_sid and adjust all of its callers as well.
CC: Paul Moore <paul@paul-moore.com>
CC: Dave Jones <davej@redhat.com>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Fan Du <fan.du@windriver.com>
CC: David S. Miller <davem@davemloft.net>
CC: LSM list <linux-security-module@vger.kernel.org>
CC: SELinux list <selinux@tycho.nsa.gov>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
There's a kmalloc with GFP_KERNEL in a helper
(pfkey_sadb2xfrm_user_sec_ctx) used in pfkey_compile_policy which is
called under rcu_read_lock. Adjust pfkey_sadb2xfrm_user_sec_ctx to have
a gfp argument and adjust the users.
CC: Dave Jones <davej@redhat.com>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Fan Du <fan.du@windriver.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
DST_NOCOUNT should only be used if an authorized user adds routes
locally. In case of routes which are added on behalf of router
advertisments this flag must not get used as it allows an unlimited
number of routes getting added remotely.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Without this fix, ipv6_exthdrs_offload_init doesn't register IPPROTO_DSTOPTS
offload, but returns 0 (as the IPPROTO_ROUTING registration actually succeeds).
This then causes the ipv6_gso_segment to drop IPv6 packets with IPPROTO_DSTOPTS
header.
The issue detected and the fix verified by running MS HCK Offload LSO test on
top of QEMU Windows guests, as this test sends IPv6 packets with
IPPROTO_DSTOPTS.
Signed-off-by: Anton Nayshtut <anton@swortex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The unix socket code is using the result of csum_partial to
hash into a lookup table:
unix_hash_fold(csum_partial(sunaddr, len, 0));
csum_partial is only guaranteed to produce something that can be
folded into a checksum, as its prototype explains:
* returns a 32-bit number suitable for feeding into itself
* or csum_tcpudp_magic
The 32bit value should not be used directly.
Depending on the alignment, the ppc64 csum_partial will return
different 32bit partial checksums that will fold into the same
16bit checksum.
This difference causes the following testcase (courtesy of
Gustavo) to sometimes fail:
#include <sys/socket.h>
#include <stdio.h>
int main()
{
int fd = socket(PF_LOCAL, SOCK_STREAM|SOCK_CLOEXEC, 0);
int i = 1;
setsockopt(fd, SOL_SOCKET, SO_REUSEADDR, &i, 4);
struct sockaddr addr;
addr.sa_family = AF_LOCAL;
bind(fd, &addr, 2);
listen(fd, 128);
struct sockaddr_storage ss;
socklen_t sslen = (socklen_t)sizeof(ss);
getsockname(fd, (struct sockaddr*)&ss, &sslen);
fd = socket(PF_LOCAL, SOCK_STREAM|SOCK_CLOEXEC, 0);
if (connect(fd, (struct sockaddr*)&ss, sslen) == -1){
perror(NULL);
return 1;
}
printf("OK\n");
return 0;
}
As suggested by davem, fix this by using csum_fold to fold the
partial 32bit checksum into a 16bit checksum before using it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Quoting Alexander Aring:
While fragmentation and unloading of 6lowpan module I got this kernel Oops
after few seconds:
BUG: unable to handle kernel paging request at f88bbc30
[..]
Modules linked in: ipv6 [last unloaded: 6lowpan]
Call Trace:
[<c012af4c>] ? call_timer_fn+0x54/0xb3
[<c012aef8>] ? process_timeout+0xa/0xa
[<c012b66b>] run_timer_softirq+0x140/0x15f
Problem is that incomplete frags are still around after unload; when
their frag expire timer fires, we get crash.
When a netns is removed (also done when unloading module), inet_frag
calls the evictor with 'force' argument to purge remaining frags.
The evictor loop terminates when accounted memory ('work') drops to 0
or the lru-list becomes empty. However, the mem accounting is done
via percpu counters and may not be accurate, i.e. loop may terminate
prematurely.
Alter evictor to only stop once the lru list is empty when force is
requested.
Reported-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Reported-by: Alexander Aring <alex.aring@gmail.com>
Tested-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Failure to schedule a TIPC tasklet with tipc_k_signal because the
tasklet handler is disabled is not an error. It means TIPC is
currently in the process of shutting down. We remove the error
logging in this case.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the TIPC module is removed, the tasklet handler is disabled
before all other subsystems. This will cause lingering publications
in the name table because the node_down tasklets responsible to
clean up publications from an unreachable node will never run.
When the name table is shut down, these publications are detected
and an error message is logged:
tipc: nametbl_stop(): orphaned hash chain detected
This is actually a memory leak, introduced with commit
993b858e37b3120ee76d9957a901cca22312ffaa ("tipc: correct the order
of stopping services at rmmod")
Instead of just logging an error and leaking memory, we free
the orphaned entries during nametable shutdown.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a topology server subscriber is disconnected, the associated
connection id is set to zero. A check vs zero is then done in the
subscription timeout function to see if the subscriber have been
shut down. This is unnecessary, because all subscription timers
will be cancelled when a subscriber terminates. Setting the
connection id to zero is actually harmful because id zero is the
identity of the topology server listening socket, and can cause a
race that leads to this socket being closed instead.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
