| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
Some new APIs will require tracing a chandef without
it being part of a channel context, so separate out
the tracing macros for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To ease further DFS development regarding interface combinations, use
the interface combinations structure to test for radar capabilities.
Drivers can specify which channel widths they support, and in which
modes. Right now only a single AP interface is allowed, but as the
DFS code evolves other combinations can be enabled.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The NL80211_ATTR_USE_MFP attribute was originally added for
NL80211_CMD_ASSOCIATE, but it is actually as useful (if not even more
useful) with NL80211_CMD_CONNECT, so process that attribute with the
connect command, too.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As per email discussion Jouni Malinen pointed out that:
"P2P message exchanges can be executed on the current operating channel
of any operation (both P2P and non-P2P station). These can be on 5 GHz
and even on 60 GHz (so yes, you _can_ do GO Negotiation on 60 GHz).
As an example, it would be possible to receive a GO Negotiation Request
frame on a 5 GHz only radio and then to complete GO Negotiation on that
band. This can happen both when connected to a P2P group (through client
discoverability mechanism) and when connected to a legacy AP (assuming
the station receive Probe Request frame from full scan in the beginning
of P2P device discovery)."
This means that P2P messages can be sent over different radio devices.
However, these should use the same P2P device address so it should be
able to provision this from user-space. This patch adds a parameter for
this to struct vif_params which should only be used during creation of
the P2P device interface.
Cc: Jouni Malinen <j@w1.fi>
Cc: Greg Goldman <ggoldman@broadcom.com>
Cc: Jithu Jance <jithu@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[add error checking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add the nl80211_mesh_power_mode enumeration which holds possible
values for the mesh power mode. These modes are unknown, active,
light sleep and deep sleep.
Add power_mode entry to the mesh config structure to hold the
user-configured default mesh power mode. This value will be used
for new peer links.
Add the dot11MeshAwakeWindowDuration value to the mesh config.
The awake window is a duration in TU describing how long the STA
will stay awake after transmitting its beacon in PS mode.
Add access routines to:
- get/set local link-specific power mode (STA)
- get remote STA's link-specific power mode (STA)
- get remote STA's non-peer power mode (STA)
- get/set default mesh power mode (mesh config)
- get/set mesh awake window duration (mesh config)
All config changes may be done at mesh runtime and take effect
immediately.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
[fix commit message line length, error handling in set station]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.
Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This functions will be used for mesh beacons, too.
Signed-off-by: Marco Porsch <marco@cozybit.com>
[some formatting fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The established peer link count is indicated in mesh beacons and
used for other internal tasks. Previously it was not updated when
authenticated peering is performed in userspace.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Ranges are taken from IEEE 802.11-2012, common sense or current
implementation requirements.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow mesh interface to disable the power save which is by default
turn on in certain chipset. Testing with 2 units of ZCN-1523H-5-16
featuring AR9280 chipset which have power save enabled by default.
Constant reset if the average signal of the peer mesh STA is below
-80 dBm and power save is enabled.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When the driver's resume function can't completely
restore the configuration in the device, it returns
1 from the callback which will be treated like a HW
restart request, but done directly.
In this case, also call the driver's restart_complete()
function so it can finish the reconfiguration there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
My commit 529ba6e9313dbe60dab7e72c6fdf647a012e9f5b
("mac80211: clean up association better in suspend")
introduced a bug when resuming from WoWLAN when a
device reset is desired. This case must not use the
suspend_bss_conf as it hasn't been stored.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"This is the first NFC patchset targeted at the 3.9 merge window.
It brings the following goodies:
- LLCP socket timestamping (To be used e.g with the recently released nfctool
application for a more efficient skb timestamping when sniffing).
- A pretty big pn533 rework from Waldemar, preparing the driver to support
more flavours of pn533 based devices.
- HCI changes from Eric in preparation for the microread driver support.
- Some LLCP memory leak fixes, cleanups and slight improvements.
- pn544 and nfcwilink move to the devm_kzalloc API.
- An initial Secure Element (SE) API.
- An nfc.h license change from the original author, allowing non GPL
application code to safely include it."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Safer and more robust than than memcpy_toiovec.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
We can cast msg_name to a sockaddr_nfc_llcp pointer directly.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
commit 1a9193185f462a51815fe48491f8a6fb6b942551 "regulatory: code cleanup"
changed is_ht40_allowed without considering that IEEE80211_CHAN_NO_HT40 is
not just one flag, but two.
This is causing HT40- to be blocked completely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
My commit 4bf88530be971bf95a7830ca61b4120980bf4347
("mac80211: convert to channel definition struct")
accidentally broke HT40 connections due to swapped
channel flag checks -- fix that.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Each NFC adapter can have several links to different secure elements and
that property needs to be exported by the drivers.
A secure element link can be enabled and disabled, and card emulation will
be handled by the currently active one. Otherwise card emulation will be
host implemented.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Some chips diverge from the HCI spec in their implementation of standard
features. This adds a new quirks parameter to
nfc_hci_allocate_device() to let the driver indicate its divergence.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Some chips use a standard HCI event code, destined to a proprietary
gate, with a different meaning. Therefore, the HCI driver must always
have a chance to intercept the event before standard processing is
attempted.
The new semantic specifies that the result value "1" means that the
driver doesn't especially handle the event. result <= 0 means it was
handled.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
There is no use to return an error if the caller doesn't get it.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
When an adapter is removed, it will unregister itself from hci and/or
nfc core. In order to do that safely, work tasks must first be canceled
and prevented to be scheduled again, before the hci or nfc device can be
destroyed.
Signed-off-by: Eric Lapuyade <eric.lapuyade@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The reference count bump on the llcp Rx path is leading to a memory leak
whenever we're not receiving an I frame.
We fix that by removing the refcount bump (drivers must not free their
received skb) and using it only in the I frame path, when the frame is
actually queued. In that case, the skb will only be freed when someone
fetches it from userspace. in all other cases, LLCP received frames will
be freed when leaving the Rx work queue.
Reported-by: Eric Lapuyade <eric.lapuyade@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Not only it was improperly use to queue backlogged RX skbuffs, but it was
also not processed at all.
If the socket receive queue is full we simply drop the incoming packets.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Set timestamp in sent and received sk_buffs. timestamp is then put in
msghdr structure in llcp_sock_recvmsg().
Signed-off-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
My commit 379b82f4c9dc6e67bf61aa61b096c06a2f320f60
("regulatory: pass new regdomain to reset function")
broke the restore_regulatory_settings() function due
to a logic change. Consider this change:
- reset_regdomains(true);
- cfg80211_regdomain = cfg80211_world_regdom;
+ reset_regdomains(true, cfg80211_world_regdom);
This looks innocent enough, until you realise that the
called function (reset_regdomains) also resets the
cfg80211_world_regdom pointer, so that the old version
of the code would use the new object it pointed to and
the new version of the code uses the old object. This
lead to a double-free of this object.
Since reset_regdomains() sets it to &world_regdom, use
that directly.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Reported-by: Bob Copeland <me@bobcopeland.com>
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The uevent callback doesn't protect its access to
last_request, which now causes a warning since
the conversion to get_last_request(). Fix this by
allowing to use RCU protection for last_request.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
One of the function names was wrong and some parameters were
missing.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The following changes are invalid and should be
disallowed when a station already exists:
* supported rates changes, except for TDLS peers
* listen interval changes
* HT capability changes
Disallow them and also update a mac80211 comment
explaining how they would be racy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When an interface is configured to a 20 MHz channel
and the device as well as the peer are 40 MHz capable
the HT capabilities of the peer are not restricted to
20 MHz, even though they're supposed to be restricted
to the currently possible capabilities.
Unset the 40 MHz HT capability bits in this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Use __aligned(...) instead of __attribute__((aligned(...)))
in mac80211 and cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Support the HT notify channel width action frame
to update the rate scaling about the bandwidth
the peer can receive in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When TX aggregation is stopped, there are a few
different cases:
- connection with the peer was dropped
- session stop was requested locally
- session stop was requested by the peer
- connection was dropped while a session is stopping
The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.
Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.
In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To call it from ___ieee80211_stop_tx_ba_session,
move the function and dependencies up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Create the function ieee80211_remove_tid_tx to call
it from ___ieee80211_stop_tx_ba_session later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The initiator/tx doesn't really identify why an
aggregation session is stopped, give a reason
for stopping that more clearly identifies what's
going on. This will help tell the driver clearly
what is expected of it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Today, stations are added already associated. That is
inefficient if, for example, the driver has no room
for stations any more because then the station will
go through the entire auth/assoc handshake, only to
be kicked out afterwards.
To address this a bit better, at least with drivers
using the new station state callback, allow hostapd
to add stations in unauthenticated mode, just after
receiving the AUTH frame, before even replying. Thus
if there's no more space at that point, it can send
a negative auth frame back. It still needs to handle
later state transition errors though, of course.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some AP code ended up in mlme.c as ap.c didn't
exist when it was written, move it now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In interoperability testing some APs showed bad behaviour
if some of the VHT capabilities of the station are better
than their own. Restrict the assoc request parameters
- beamformee capabable,
- RX STBC and
- RX MCS set
to the subset that the AP can support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We should not add new beacon hints even if the wiphy
is not world roaming. Without this we were always adding
a beacon hint if not world roaming for every non world
roaming wiphy interface.
Tested-by: Ben Greear <greearb@candelatech.com>
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[fix locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This will be used later by other code. This has no
functional change.
Tested-by: Ben Greear <greearb@candelatech.com>
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Regulatory beacon hints are used to help with world roaming
and as it is right now we learn from a beacon hint processed
on one wiphy to all other wiphys. The processing of beacon
hints however is scheduled and if we have a lot of interfaces
we may hit the case that we'll queue a the same beacon hint
many times until its processed.
To avoid this do a lookup on the queued up beacon hints prior
to adding a new beacon hint. If the beacon hint is removed
from the pending reg beacon hint list then it would be processed
and we'd ensure all wiphys would have learned from it, if its
on the pending reg beacon list we'd now find it prior to it
being processed.
Tested-by: Ben Greear <greearb@candelatech.com>
Reported-by: Ben Greear <greearb@candelatech.com>
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of checking every time bss_info_changed is called,
assign the pointer once depending on the interface type
and then leave it untouched until the interface type is
changed. This makes the ieee80211_bss_info_change_notify()
now a simple wrapper to call the driver only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The special case in the function isn't really needed,
instead make the suspend code a bit better and also
easier to understand and move the warning into the
driver op wrapper inline.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
For AP/IBSS/mesh interfaces, call the driver to reconfigure
bss_info_changed only if the interface was beaconing before
suspend, otherwise we call the driver and it might interpret
the change as going from enabled to disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of calculating in ieee80211_bss_info_change_notify()
whether beaconing should be enabled or not, set it in the
correct places in the callers. This simplifies the logic in
this function at the expense of offchannel, but is also more
robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
During suspend/resume channel contexts might be
iterated even if they haven't been re-added to
the driver, keep track of this and skip them in
iteration. Also use the new status for sanity
checks.
Also clarify the fact that during HW restart all
contexts are iterated over (thanks Eliad.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When suspending, bss_info_changed() is called to
disable beacons, but managed mode interfaces are
simply removed (bss_info_changed() is called with
"no change" only). This can lead to problems.
To fix this and copy the BSS configuration, clear
it during suspend and restore it on resume.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
