| Age | Commit message (Collapse) | Author |
|---|
|
CONFIG_SND_HDA_I915 doesn't have to be user-selectable as this is almost
mandatory when i915 driver is available. Let's enable it always when
CONFIG_DRM_I915 is set, so that user won't be bothered by useless
questions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds two fields to unsolicited response, according to spec HDA040-A:
- Device Entry (bit 20:15)
- Inactive (bit 2)
and show the info in debug message.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch is only to allow codec proc file to expose devices list/select info
for Haswell codec pins.
Since Haswell Gfx driver cannot support DP1.2 MST now, so all pins' device list
is empty, meaning no pin is multi-streaming capaple.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If a display codec supports multi-stream transport on the pins, the pin's
device list length and device entries will be exposed to codec proc file.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds flags and routines to get device list & selection info on
a pin.
To support Display Port 1.2 multi-stream transport (MST) over single DP port,
a pin can support multiple devices. Please refer to HD-A spec Document Change
Notificaton HDA040-A.
A display audio codec can set flag "dp_mst" in its patch, indicating its pins
can support MST. But at runtime, a pin may not be multi-streaming capable and
report the device list is empty, depending on Gfx driver configuration.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.12
- DAPM is now mandatory for CODEC drivers in order to avoid the repeated
regressions in the special cases for non-DAPM CODECs and make it
easier to integrate with other components on boards. All existing
drivers have had some level of DAPM support added.
- A lot of cleanups in DAPM plus support for maintaining controls in a
specific state while a DAPM widget all contributed by Lars-Peter Clausen.
- Core helpers for bitbanged AC'97 reset from Markus Pargmann.
- New drivers and support for Analog Devices ADAU1702 and ADAU1401(a),
Asahi Kasei Microdevices AK4554, Atmel AT91ASM9x5 and WM8904 based
machines, Freescale S/PDIF and SSI AC'97, Renesas R-Car SoCs, Samsung
Exynos5420 SoCs, Texas Instruments PCM1681 and PCM1792A and Wolfson
Microelectronics WM8997.
- Support for building drivers that can support it cross-platform for
compile test.
|
|
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixing warning message:
sound/pci/rme96.c: In function ‘snd_rme96_resume’:
sound/pci/rme96.c:2418:19: warning: ignoring return value of ‘pci_enable_device’, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The headphone automute on this machine triggers annoying pop noises.
It seems that only the first DAC can be used, the secondary DAC always
results in this problem. This patch disables the secondary DAC with
a few additional workarounds.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fixed ALC283 D3 to D0 and D0 to D3 Headphone pop noise.
The previous fix [c5177c86: ALSA: hda - Fix the noise after suspend on
ALC283 codec] doesn't work sufficiently for some laptops.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Without proper power management handling, the first use
of a Digi96/8 anytime after a suspend / resume cycle will
start playback with distortions.
v3: Abort if vmalloc() of suspend buffers fail, but do not
leak memory in that case.
[fixed wrong memory leak fix again -- tiwai]
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch doesn't change functionality, it only improves readability
and fixes a copy&paste error in a comment.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use enum hdspm_ltc_format's fps_30 (corresponds to 4) instead of 30,
Other case branches return 1, 2 or 3 respectively, so 30 obviously is
wrong.
Since SNDRV_HDSPM_IOCTL_GET_LTC had never been working due to a
copy&paste error in hdspm.h, this change doesn't break userspace.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
If compiled without CONFIG_SND_HDA_I915, the audio driver cannot
request power well. However, if the power well is on for other
reasons, maybe audio can still work. Therefore, do not skip the
card completely if compiled without CONFIG_SND_HDA_I915.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The higher mic boosts (on internal mic) are so noisy they're unusable
in practice.
BugLink: https://bugs.launchpad.net/bugs/1213820
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This just cleans up the table, no functional changes.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The internal mic boost is so noisy on boosts 2 and 3 so they are
unusable in practice.
BugLink: https://bugs.launchpad.net/bugs/1213055
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Gateway LT27 needs a fixup for the inverted digital mic.
Reported-by: "Nathanael D. Noblet" <nathanael@gnat.ca>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The hardware does support synchronized start/pause/stop of pcm streams,
so there is no reason not to add that feature after more than ten years.
Some minor coding style / white space fixes in the surroundings of the
changes.
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The current generic parser code assumes that always a pin widget
controls the mute for an output blindly although it might be a
different widget in the middle. Instead of the fixed assumption,
check each parsed path and just pick up the right widget that has been
already defined as a mute control.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The auto-mute using the amp currently works only for a single amp on a
pin. Make it working also with HDA_CTL_BIND_MUTE type, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We've added a fake mute control (setting the amp volume to zero) for
CX5051 at commit [3868137e: ALSA: hda - Add a fake mute feature], but
this feature was overlooked in the generic parser implementation. Now
the driver lacks of mute controls on these codecs.
The fix is just to check both AC_AMPCAP_MUTE and AC_AMPCAP_MIN_MUTE
bits in each place checking the amp capabilities.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59001
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Correct the pins for a line-in and a headphone on LG LW25 laptop with
ALC880 codec. Other pins seem fine.
Reported-and-tested-by: Joonas Saarinen <jonskunator@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The snd_hda_jack_set_gating_jack() call didn't work when
auto_{mute,mic} is suppressed because (1) am_entry is
not filled with nid of the mic pin. (2) The jacks are not
created (by snd_hda_jack_detect_enable_callback) before the
snd_hda_jack_set_gating_jack call.
Now we use the first input pin nid directly, and create the jack if it
doesn't exist yet.
Signed-off-by: Chih-Chung Chang <chihchung@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A fixup for Apple Mac Mini was lost during the adaption to the generic
parser because the fallback for the generic ID 8384:7680 was dropped,
and it resulted in the silence output (and maybe other problems).
Unfortunately, just adding the missing subsystem ID wasn't enough, in
this case. The subsystem ID of this machine is 0000:0100 (what Apple
thought...?), and since snd_hda_pick_fixup() doesn't take the vendor
id zero into account, the driver ignored this entry. Now it's fixed
to regard the vendor id zero as a valid value.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
VAIO-Z laptops need to use the specific DAC for the speaker output
by some unknown reason although the codec itself supports the flexible
connection. So we implemented a workaround by a new flag,
no_primary_hp, for assigning the speaker pin first.
This worked until 3.8 kernel, but it got broken because the driver
learned for a better multi-io pin mapping, and not it can assign two
mic pins for multi-io. Since the multi-io requires to be the primary
output, the hp and two mic pins are assigned in prior to the speaker
in the end.
Although the machine has two mic pins, one of them is used as a noise-
canceling headphone, thus it's no real retaskable mic jack. Thus, at
best, we can disable the multi-io assignment and make the parser
behavior back to the state before the multi-io.
This patch adds again a new flag, no_multi_io, to indicate that the
device has no multi-io capability, and set it in the fixup for
VAIO-Z. The no_multi_io flag itself can be used generically, added
via a helper line, too.
Reported-by: Tormen <my.nl.abos@gmail.com>
Reported-by: Adam Williamson <awilliam@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The current fixup for dell-bios model with STAC9228 codec contains the
override of pin 0x0c for analog mic. But this is actually just adding
a bogus pin and confuses the parser. Better to remove it for the
auto-mic switching.
Meanwhile, for a possible regression, keep the old configuration as
model=dell-bios-amic, so that people can test it again quickly.
Tested on Dell 1420n laptop.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
With runtime power save feature enabled, Headphone hotplug
event will not be detected while controller/codec in D3. HDA has
feature WAKEEN to let codec wake up system if controller is in D3 or
system in S3.(HDA Spec 4.5.9.2/3). Codec can send out INT or wake up
controller depending on whether CIE or GIE enabled.(Figure 4, Interupt
structure).
The controller must be in RESET mode after enter runtime-suspend, otherwise
it will not be waken up even if codec send out wake-up event. And STATESTS
will be cleared after controller brought out of RESET mode.
This patch only enable WAKEEN for runtime-suspend(Controller D3) mode,
not for system S3 mode. with tool "evtest", Headphone hotplug events
could be cought and reported successfully.
[fixed an unused variable warning by tiwai]
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
With jackpoll_interval != 0, it's used to poll jack event periodically
in a delayed work. if it's 0, give the caller chance to probe jack status
but will not restart the delayed work.
In the next patch which enable WAKEEN feature, HDA controller was able to wake
up system when it's in D3, it's useful to detect Jack hotplug event and notify
userspace. By default the jackpoll_interval=0, this patch let jack poll once
without starting the delayed work.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Clearing jackpoll_interval before calling cancel_delayed_work_sync(),
otherwise the work will be triggered again and cause impact in
hda_jackpoll_work(). The next patch will poll jack once even with
jackpoll_interval=0.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Register STATESTS is 16-bit length, use correct API for read/write.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When the power state of ALC283 codec goes to D3, it gives a noise via
headphone output. This is because the driver tries to clear all pins
via snd_hda_shutup_pins(). Setting the mic pin to zero triggers such
a noise.
Define a new shutup call specific to this codec and control the pins
there more precisely. Also, add the power-save enable/disable
sequences in the resume and the new shutup calls.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Instead of calling snd_hda_shutup_pins() unconditionally, allow it be
called in spec->shutup callback. In this way, we can avoid calling
this function if it causes a problem like we see in the next patch
following this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The usage of strict_strto*() is not preferred, because
strict_strto*() is obsolete. Thus, kstrto*() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_hda_jack_detect() function returns a boolean value for a jack
plugged in or not, but it also returns always true when the
corresponding pin is phantom (i.e. fixed). This is OK in most cases,
but it makes the generic parser misbehaving about the auto-mute or
auto-mic switching, e.g. when one of headphone pins is a fixed.
Namely, the driver decides whether to mute the speaker or not, just
depending on the headphone plug state: if one of the headphone jacks
is seen as active, then the speaker is muted. Thus this will result
always in the muted speaker output.
So, the problem is the function returns a boolean, after all, although
we need to think of "phantom" jack. Now a new function,
snd_hda_jack_detect_state() is introduced to return these tristates.
The generic parser uses this function for checking the headphone or
mic jack states.
Meanwhile, the behavior of snd_hda_jack_detect() is kept as is, for
keeping compatibility in other driver codes.
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The quirk for Dell laptops with STAC9228 overrides the pin default
config of NID 0x0f to the value with AC_DEFCFG_MISC_NO_PRESENCE bit
on. I'm not quite sure why this was done so, but can guess that this
was introduced for avoiding this to be muted by another headphone
plug. Now, after transition to the generic parser, this workaround
rather causes a problem (notably as unexpected speaker mutes) because
the pin is seen as if it's always plugged in.
Since the generic parser can handle multiple headphone plugging
gracefully, we can get rid of this override now.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The EAPD GPIO is dynamically turned on/off for some machines with
Sigmatel codecs, but this didn't work as expected, and it resulted in
spontaneous lost of speaker outputs per HP plugging or power-saving.
This patch fixes the bug by simply including spec->eapd_mask into
spec->gpio_mask and spec->gpio_data bits.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This Conexant codec has a single jack that can be used as either
headphone or mic (but not headset). The existing hp_mic functionality
does not apply here, because the mic and the HP are on separate pins.
Hence make a lighter version of what has been earlier done for Realtek
codecs.
BugLink: https://bugs.launchpad.net/bugs/1198030
Tested-by: Franz Hsieh <franz.hsieh@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Vendor ID 0x10de0060 is used by a yet-to-be-named GPU chip.
Reviewed-by: Andy Ritger <aritger@nvidia.com>
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_pcm_stop() must be called in the PCM substream lock context.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
sound/pci/rme9652/hdspm.c:1110:2-3: Unneeded semicolon
Generated by: coccinelle/misc/semicolon.cocci
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A few small fixes (and cleanups) for HD-audio, USB-audio and ASoC"
* tag 'sound-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: fix regression for fixed stream quirk
ALSA: hda - Keep halting ALC5505 DSP
ASoC: wm8962: fix NULL pdata pointer
ASoC: imx-sgtl5000: return E_PROBE_DEFER if ssi/codec not found
ASoC: Samsung: Remove redundant comment
ALSA: hda - Fix EAPD vmaster hook for AD1884 & co
ASoC: samsung: Remove obsolete GPIO based DT pinmuxing
ASoC: mxs: register saif mclk to clock framework
|
|
|
|
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
|
|
ALC5505 DSP is enabled even though we don't use the features yet at
all. This results in the unnecessarily high power consumption, more
than 100mV higher. Until we implement the DSP support, better to
bypass DSP for saving more power.
Reported-by: Mengdong Lin <mengdong.lin@intel.com>
[Patch modified by Mengdong to cal alc5505_dsp_init() with extra
acl5505_dsp_halt().]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Martin Dausel <martin.dausel@iosono-sound.com>
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Also use snd_ctl_enum_info() to fill the autosync text fields on AES32
and MADI cards (only users of snd_hdspm_info_autosync_ref).
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Also use snd_ctl_enum_info() to fill the autosync enumerated controls.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
