summaryrefslogtreecommitdiffstats
path: root/sound/soc/codecs
AgeCommit message (Collapse)Author
2010-12-14ASoC: twl6040: Use correct offset for LineInAmp RightMisael Lopez Cruz
Gain for LineInAmp Right uses LINEGAIN[5:3], which means that offset for right channel should be 4. Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com> Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Fix TLV dB step values for gainsOlaya, Margarita
Some gains were incorrectly configured for dB values. Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Increase timeout for power upJorge Eduardo Candelaria
After coming back from suspend, the timeout waiting for Phoenix chip to complete its power up sequence is not enough, which leaves the codec cache value for some registers in an outdated state. Increase the timeout value to wait for the power up sequence to correclty complete. Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com> Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Enable plug detection interruptsMisael Lopez Cruz
Enable plug detection interrupt mask in order to get headset PLUGINT/UNPLUGINT interrupts. Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com> Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Clear interrupt status at boot timeJorge Eduardo Candelaria
On Phoenix 1.1, the INTID register default value is an invalid one, causing the interrupt handler to think the phoenix power on sequence is ready before it actually finishes. This causes some i2c errors when trying to configure twl. Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com> Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Enable automatic power for phoenix 1.1Olaya, Margarita
Phoenix 1.1 supports automatic power on sequence, a verification is added to use it with new revision of the chip. Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Fix analog Mic L & R mux controlsFrancois Mazard
The mux control has 4 elements not 3 Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Support other sample rates.Olaya, Margarita
The twl6040 can support more sample rates other than 88.2 and 96k. Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Fix PCM error handling opsOlaya, Margarita
This patch moves all the PCM error handling for clock config out of trigger() and startup() and into prepare(). Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Restore bias level at resumeOlaya, Margarita
This patch restores the CODEC bias level at resume(). Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Add headset and handset mux controlsJorge Eduardo Candelaria
This patch adds support for the twl6040 headset and handset MUX controls. Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com> Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Modify the IRQ handlerOlaya, Margarita
Multiples interrupts can be received. The irq handler is modified to attend all of them. Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Update twl IO macroOlaya, Margarita
Update the codec to use the new twl core register macros Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: twl6040: Add jack support for headset and handsetJorge Eduardo Candelaria
This patch adds support for reporting twl6040 headset and handset jack events. The machine driver retrieves and report the status through twl6040_hs_jack_detect. A workq is used to debounce of the irq. Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com> Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com> Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: TWL4030: Fix 24bit supportPeter Ujfalusi
twl4030 series of codecs supports S32_LE with msbits=24. Replace the S24_LE with S32_LE format, and add constraint for 24msbit in case of 32 S32_LE format. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-14ASoC: Explicitly clear WM8993 ramp controls on power downMark Brown
This helps ensure that the ramp logic is reset when powering back up. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-13Merge branch 'topic/asoc' of ↵Mark Brown
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 into for-2.6.38
2010-12-13ASoC: Fix merge errors with flush_scheduled_work() removalTakashi Iwai
delayed_work was moved to dapm in the commit ce6120cca2589ede530200c7cfe11ac9f144333c ASoC: Decouple DAPM from CODECs Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-13ASoC: Fix widgets for WM8994/58 AIF2 source controlMark Brown
The compiler really ought to have been warning about unreferenced variables... Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-13Merge branch 'topic/workq-update' into topic/asocTakashi Iwai
Conflicts: sound/soc/codecs/wm8350.c sound/soc/codecs/wm8753.c sound/soc/sh/fsi.c sound/soc/soc-core.c
2010-12-13sound: don't use flush_scheduled_work()Tejun Heo
flush_scheduled_work() is deprecated and scheduled to be removed. * cancel[_delayed]_work() + flush_scheduled_work() -> cancel[_delayed]_work_sync(). * wm8350, wm8753 and soc-core use custom code to cancel a delayed work, execute it immediately if it was pending and wait for its completion. This is equivalent to flush_delayed_work_sync(). Use it instead. Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2010-12-11ASoC: Automatically manage WM8903 deemphasis rateMark Brown
Provide the user with a boolean control then automatically select the deemphasis filter most closely matching the sample rate. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-11ASoC: Remove open coded symmetry implementation from WM8903Mark Brown
We're already flagged as using symmetric rates so we don't need to have a custom implementation. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-11ASoC: Implement WM8903 oversampling rate controlsMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-11ASoC: Implement WM8903 high pass filter supportMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-10ASoC: tlv320dac33: Power down digital parts, when not neededPeter Ujfalusi
If the following scenario has been followed: 1. Enable analog bypass amixer sset 'Analog Left Bypass' on amixer sset 'Analog Right Bypass' on 2. Start playback aplay -fdat -d3 /dev/zero After the playback stopped (3 sec), and the soc timeout (5 sec), the digital parts of the codec will remain powered up. This means that the DAI clocks are continue to run, the oscillator remain operational, etc. Use the SND_SOC_DAPM_POST_PMD widget to get notification about the stopped stream, and power down the digital part of the codec. If the analog bypass is enabled, than the codec will remain in BIAS_ON level, and things will work correctly. In case, if the bypass is disabled, than the codec will fall to BIAS_STANDBY than to BIAS_OFF level, as it used to. The digital part of DAC33 is initialized at every stream start (DAPM_PRE:PRE_PMU event), so subsequent streams (within 5 sec) will have working DAI. When the codec is coming out from BIAS_OFF, the full power-up sequence followed by the same DAPM_PRE widget event will power up the digital part. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-10ASoC: Implement WM8994/58 DAC and ADC oversampling controlMark Brown
The oversampling rate of the DAC and ADC can be controlled to optimise for either low power consumption or maximum performance. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-10ASoC: Optimise WM9081 FLL performanceMario Becroft
Tune the FLL gain for optimal performance according to evaluation results. Signed-off-by: Mario Becroft <mb@gem.win.co.nz> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-12-09Merge branch 'for-2.6.37' into for-2.6.38Mark Brown
2010-12-09ASoC: WM8580: Fix R8 initial valueSeungwhan Youn
Acc to WM8580 manual, the default value for R8 is 0x10, not 0x1c. Signed-off-by: Seungwhan Youn <sw.youn@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
2010-12-09ASoC: fix deemphasis control in wm8904/55/60 codecsDmitry Artamonow
Deemphasis control's .get callback should update control's value instead of returning it - return value of callback function is used for indicating error or success of operation. Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
2010-12-09ASoC: tlv320dac33: Fix compillation errorPeter Ujfalusi
Fix the compilation error introduced by patch: ASoC: tlv320dac33: Avoid multiple soft power up Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-09ASoC: tlv320dac33: Move DAC LR power on to a supply widgetPeter Ujfalusi
The power for the DACs need to be enabled, even when only the analog bypass is in use with the codec, otherwise the audio is going to be distorted. Make sure that the DACs are powered all the time, when there is audio activity. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-09ASoC: tlv320dac33: Rename outpup amplifier widgetPeter Ujfalusi
Use better name for the widget, and remove the 'Power' from it's name. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-08ASoC: Add ADC high pass filter support to WM8994Uk Kim
Signed-off-by: Uk Kim <w0806.kim@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-12-08ASoC: Support WM8994 mono AIF configurationsMark Brown
The WM8994 supports mono signals - enable this in the driver. With DSP mode an automatic data channel selector is available, activate this when in mono mode. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-08Merge branch 'for-2.6.37' into for-2.6.38Mark Brown
Conflicts: sound/soc/soc-core.c Axel's fix on two different branches.
2010-12-07ASoC: Correct WM8962 interrupt mask register readMark Brown
Fix mismerge from the out of tree BSP where this support was developed. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-12-07ASoC: WM8580: Debug BCLK and sample sizeJassi Brar
In case of SNDRV_PCM_FORMAT_S32_LE, we need to set WM8580_AIF_LENGTH_32, rather than WM8580_AIF_LENGTH_24. Also, the BCLK has to be 64fs, for sample size of 20, 24 and 32 bits. Signed-off-by: Jassi Brar <jassi.brar@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-12-06Merge branch 'for-2.6.37' into for-2.6.38Mark Brown
Conflicts: include/linux/mfd/wm8994/pdata.h
2010-12-06ASoC: Fix swap of left and right channels for WM8993/4 speaker boost gainUk Kim
SPKOUTL_BOOST start from third bit, SPKOUTLR_BOOST start from 0 bit. Signed-off-by: Uk Kim <w0806.kim@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
2010-12-03ASoC: When disabling WM8994 FLL force a source selectionMark Brown
When we disable the WM8994 FLL code path sharing means that we end up writing out a configuration. Currently this is the currently active input and output frequency (which causes snd_soc_update_bits() to suppress actual writes both immediately and in the common case where we reenable the same configuration later) but we allow machine drivers to pass through a source of zero. Since the register values written are one less than the source constants this causes corruption of other bitfields in the register. Fix this by using the most recently configured FLL source when none is provided. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Cc: stable@kernel.org
2010-12-03ASoC: WM8580: Debug interface indexJassi Brar
We want the index of DAI's driver here. Signed-off-by: Jassi Brar <jassi.brar@samsung.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-12-03ASoC: Fix inconsistent meaning of default case while checking alc5623->idAxel Lin
In alc5623_i2c_probe(), the default case for checking alc5623->id behaves the same as case 0x23. However, In alc5623_probe() the default case for checking alc5623->id becomes to be the same as case 0x21. This makes the meaning of default case inconsistent. Since we have checked codec id in alc5623_i2c_probe() by comparing vid2 with id->driver_data, it is not possible to run into the default case now. In case we may add more supported devices to alc5623_i2c_table in the future, this patch changes the default case return -EINVAL to let people know that they should not run into this case. They should also add a new case accordingly for the new id. Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Arnaud Patard <arnaud.patard@rtp-net.org> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2010-12-02ASoC: Tune performance of WM8958 revision AMark Brown
Update some of the default configuration for the device to improve the performance. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-02ASoC: Automatically manage WM8731 deemphasisMark Brown
The deemphasis filter should be selected based on sample rate for optimal performance. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-02ASoC: Split WM8731 enumeration array into individual enumsMark Brown
This is much more maintainable than the array. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-02ASoC: Provide WM8731 microphone boost TLV informationMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-02ASoC: Remove unused aic3x_i2c_init and aic3x_i2c_exit functionsAxel Lin
Signed-off-by: Axel Lin <axel.lin@gmail.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Acked-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
2010-12-02ASoC: tpa6130a2: Replace DAPM code with direct interfacePeter Ujfalusi
The use of DAPM widgets, and extra routing can cause ordering problems in the system. Machine drivers should use the exported direct interface with SND_SOC_DAPM_HP's event callback to manage the state of the amplifier. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-28 06:12:06 +0000