| Age | Commit message (Collapse) | Author |
|---|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
|
|
Commit 4eaa9819dc08d7bfd1065ce530e31b18a119dcaf changed semantics of
private_value member of kcontrol. This resulted in inability to control
amplifier and subsequently in very low output volume.
Tested-by: Johannes Schauer <josch@pyneo.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Unsigned variables should use `%u' rather than `%d'.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Merge branch 'devel-gpio' into for-rmk-devel
|
|
Move all the gpio functions out of <mach/hardware.h> as
this file is for defining the generic IO base addresses
for the kernel IO calls.
Make a new header <mach/gpio-fns.h> to take this and
include it via the chain from <linux/gpio.h> which is
what most of these files should be using (and will be
changed as soon as possible).
Note, this does make minor changes to some drivers but
should not mess up any pending merges.
CC: Richard Purdie <rpurdie@rpsys.net>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
calls
The S3C24XX DMA API channel configuration registers are being passed
values comprised of register values which makes it hard to move the
API to cover both the S3C24XX and S3C64XX.
These values can be calculated from knowing which device the channel
is connected to, so remove them from the two calls s3c2410_dma_config
and s3c2410_dma_devconfig.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
They aren't used by anything external and aren't prototyped; if any
users appear they can be exported again for them.
Also report what modes we have a problem with when we encounter invalid
mode configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Aids debugging.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
On startup we try to make sure that the port is quiesced but if the
port is already stopped then this will generate a warning about the
RX/TX mode configuration. Configure the mode before doing the teardown
to suppress these warnings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The data format configuration for S3C64xx IISv2 is completely different
to that for S3C24xx. Instead of a single bit configuration in bit 0 of
IISMOD we have format selection in bits 13 and 14 and bit clock rate
selection in bits 1 and 2. While we're here add support for 24 bit
samples in S3C64xx.
At some point it may be desirable to expose the bit clock rate selection
to users but given the limited configuration options that may not be
required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This makes the interface usable with the s3c-iis-v2 rate calculator
and consistent with S3C2412.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Make sure we get the DAI operations initialised.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Say what invalid values we're seeing when we see an invalid value and
ensure that errors are displayed by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
There is only one LRCLK pin on each interface.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
* fix/asoc:
ASoC: s3c-i2s-v2 needs to declare a license for modular builds
ASoC: remove non-existing referece to CONFIG_SND_SOC_CODEC_WM8991
ASoC: Fix WM8580 volume update handling for large register changes
ASoC: Fix offset of freqmode in WM8580 PLL configuration
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The S3C64xx IIS code had a number of problems with device registration.
The hardware has two IIS ports of which the driver supported only one
at once via a single exported DAI, attempting to identify the DAI to
use based on the dev->id of the ASoC platform device. As well as
limiting the driver to only supporting one IIS port at once this also
meant that the ID of the soc-audio device (or in future the card device)
had to match the IIS ID.
Fix both problems by converting the driver to register the DAIs based on
probing of platform devices registered by the arch/arm code, using those
platform devices to interact with the clock API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
It relies on EXPORT_SYMBOL_GPL() symbols.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
* fix/asoc:
ASoC: OMAP: Fix FS polarity in OSK5912 machine driver
ASoC: OMAP: Fix DSP_B format in OMAP McBSP DAI driver
ASoC: Fix include build error in s3c2412-i2s.c
ASoC: Fix s3c-i2s-v2.c snd_soc_dai changes
ASoC: s3c-i2s-v2.c fix for s3c_i2sv2_iis_calc_rate
ASoC: Fix jive_wm8750.c build problems
ASoC: pxa-ssp: allow setting of dai format 0
|
|
|
|
Fix accidental change of <mach/regs-gpio.h> to
<plat/regs-gpio.h> in s3c2412-i2s.c
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Fix the build error in s3c-i2s-v2.c caused by
a change to the snd_soc_dai ops field.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The definition of s3c_i2sv2_iis_calc_rate was never
renamed from s3c2412_iis_calc_rate, so rename this
to allow the build to work.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Fix build errors in sound/soc/s3c24xx/jive_wm8750.c
from changes to ASoC.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6 into topic/asoc
|
|
Due to the process and communications issues with the 2.6.30 S3C
platform merges none of the underlying arch/arm code for S3C64xx audio
support made it into mainline, rendering the drivers useless. Disable
them in Kconfig to avoid user confusion - users patching in the required
support can always reenable this too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The drivers are basically duplicating the same code over and over.
As snd_soc_cnew is going to be made static some time after the next
merge window, we might as well convert them now.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Merge Eric Maio's patch to merge snd_soc_dai_ops out of line. Fixed
merge issues and updated drivers, plus an issue with the ops for the two
s3c2443 AC97 DAIs having been merged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The register values are all u32 so don't need the long format.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6 into topic/asoc
|
|
Remove a non-existing Kconfig CONFIG_SND_SOC_WM8750_SPI.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Upgrade the severity of some failure messages from debug level so
they're displayed by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The recent set of S3C64xx patches re-added a lot of uses of DBG() that
had previously been removed - revert this so the standard pr_debug()
macro is used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
We now support the 64xx series as well as the 24xx series - make sure
people using Kconfig know this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Remove uneeded startup callback and use snd_soc_dapm_nc_pin()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Select the relevant DMA implementation when the
sound driver is selected.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Add the initial code to support the S3C64XX I2S hardware using the
s3c-i2s-v2 core code.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The S3C2412 I2S (IIS) interface is replicated on further Samsung SoC
parts in a broadly compatible way, so split the common code out into
a core called s3c-i2s-v2.[ch] so that the newer SoCs such as the
S3C6410 can make use of it.
As such, all the original s3c2412 functions are currently being left
with their original names, and will be renamed later in the series.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Add support for the Jive's WM8750 codec attached via the S3C2412 IIS.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
The <mach/audio.h> file needs to be common to both ARCH_S3C2410 and
ARCH_S3C64XX as they share common driver code, so move it to <plat/audio.h>.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Move the IIS headers to their correct place.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
