| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Try to spot locking issues by asserting that the DAPM mutex is held when
it should be. There's a bit of fun due to us not requiring the lock to be
held prior to the card being instantiated which mean we need to wrap the
assert in some paths and this isn't methodical by any stretch of the
imagination.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The function is not called outside soc-dapm.c so there is no need for it
to be exported.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The new sequence ensure that dapm_pre_sequence_async work on
the card before all codecs and dapm_post_sequence_async work
on the card after all codecs.
So the machine driver could utilize the determinate sequence
to do the gloabl setup and teardown in the right place.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The widgets generated by the machine driver need to power off too.
Signed-off-by: Xiang Xiao <xiaoxiang@xiaomi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There are three different completely independent code paths in
dapm_set_path_status(). One of them is never used at all and the other two (one
for mixers, one for MUXs) have their distincive callsites that always go onto
the same path. Breaking the function into two parts allows us to reduce the code
size and in the MUX case also do some optimizations to avoid having to calcualte
the selected item for each item again.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
MUXs and virtual MUXs are almost identical, the only difference is that for
virtual MUX there is no hardware backing register in which setting is stored.
This patch adds code, which is similar to what we already do for DAPM mixer
controls to support virtual mixer controls, to DAPM enum controls. The new code
will check if the enum does a hardware backing register and skip over reading
and writing to the register if it has not. This allows us to use the same code
path for both MUXs and virtual MUXs and a lot of nearly identical code can be
removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
MUXs and value MUXs are almost identical, the only difference is that a value
MUX uses a look-up table to map from the selected control item to a register
value, while MUXs use a direct mapping. This patch uses
snd_soc_enum_item_to_val() and snd_soc_enum_val_to_item(), which where earlier
introduced during the consolidation of enum and value enum controls, to hide
this difference. This allows us to use the same code path for both MUXs and
value MUXs and a lot of nearly duplicated code can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
'topic/max98090', 'topic/mc13783', 'fix/wm8994' and 'topic/wm8995' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-enum
|
|
We will often call sync after several functions that require the DAPM
mutex to be held. Rather than release and immediately relock the mutex
provide an unlocked function for this situation.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-dapm
|
|
The snd_soc_dapm_xxxx_pin all require the dapm_mutex to be held when
they are called as they edit the dirty list, however very few of the
callers do so.
This patch adds unlocked versions of all the functions replacing the
existing implementations with one that holds the lock internally. We
also fix up the places where the lock was actually held on the caller
side.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
|
|
The name "max" in struct soc_enum is rather confusing since it
actually takes the number of items. With "max", one might try to
assign (nitems - 1) value.
Rename the field to a more appropriate one, "items", which is also
used in struct snd_ctl_elem_info, too.
This patch also rewrites some code like "if (x > e->nitems - 1)" with
"if (x >= e->nitems)". Not only the latter improves the readability,
it also fixes a potential bug when e->items is zero.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The error messages for bypassing/unbypassing a regulator appear to be
swapped round, this patch corrects these.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Commit f7d3c1709 ("ASoC: dapm: Change prototype of soc_widget_read") changed the
signature of soc_widget_read() so that it, instead of return the register value
as a int, takes a pointer to a unsigned int and stores the register value in
that pointer. There are still a few places that pass a int type value to that
function though. Change these to unsigned int. For more consistency also change
the signature of soc_widget_write() to take a unsigned int instead of an int for
the register value.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The prefix for the codec driver can be used during dual identical
codec usecases. However, dapm adds prefix twice for codec DAI widget
in snd_soc_dapm_add_route API.
This change is to avoid double prefix addition for codec DAI widget
and is needed while using identical dual codecs.
Signed-off-by: Songhee Baek <sbaek@nvidia.com>
Signed-off-by: Arun Shamanna Lakshmi <aruns@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
soc_widget_read API returns the register data and it is possible
that a register can contain 0xffffffff. Thus, change the prototype
of soc_widget_read to return only the error code and pass the reg
data through pointer argument.
Signed-off-by: Arun Shamanna Lakshmi <aruns@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Connect the DAPM graph through each BE DAI link to the componnent(s) on the
other side of the BE DAI link. This allows the graph to be walked on
both sides of the link when graph changes are made.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
DPCM can dynamically alter the FE to BE PCM links at runtime based
on mixer/mux setting updates. Add soc_dpcm_runtime_update() calling in
get/put function for mixer/mux to support this feature.
Signed-off-by: Nenghua Cao <nhcao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.13
Some additional fixes for v3.13, the majority of which are removals and
downgrades of BUG()s from Takashi.
|
|
|
|
|
|
Leaving BUG_ON() in a core layer like dapm is rather inappropriate as
it leads to panic(), even though sanity checks might be still useful
for debugging.
Instead, Use WARN_ON(), and handle the error cases accordingly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
BUG() used in the driver is just to spit the stack trace on buggy
points, not really needed to stop the whole operation. For that
purpose, it'd be more convenient to use WARN() instead with more
error information.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
... instead of NULL dereferences.
Spotted by coverity CID 402004.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
... due to a copy & paste error.
Spotted by coverity CID 710923.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
|
|
In order to avoid trying to use an external clock or supply for an
on-chip supply prior to it being enabled move the clock and regulator
supply events to a separate step in DAPM sequencing from normal supply
events.
This should have minimal practical impact since these widgets are sorted
using SND_SOC_NOPM which is a negative value and hence sorted
separately to any real register writes, though it may be relevant if
supplies have event callbacks only.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Within a DAPM sequence we normally don't care about when exactly a register
write has completed so long as they happen in the order we requested. This
means that we can issue most of the writes we do asynchronously which
should maximise the ability of the underlying frameworks to keep the
hardware busy, providing a small performance improvement on some systems.
We currently ensure that all writes are completed both when changing to a
different device and when calling into the regulator and clock frameworks.
This should ensure that the previous ordering is maintained.
We also ensure that writes are completed prior to calling into widget
event functions since some event functions implement delays. This
should be improved in future so that widgets can disable this sync in
order to add extra writes.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch adds support for virtual DAPM mixer controls. They are similar to
virtual DAPM enums. There is no hardware register backing the control, so
changing the control's value wont have any direct effect on the hardware. But it
still influences the DAPM graph by causing the path it sits on to be connected
or disconnected. This in turn can cause power changes for some of the widgets on
the DAPM graph, which will then modify the hardware state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
VMID widgets behave very similar to signal generator widgets. Both are always
considered to be powered up. This means that we need to ignore the VMID widgets
in the same way as signal generator widgets when calculating the DAPM context's
target bias level. Otherwise the presence of a VMID widget, regardless whether
it is on an active path or not, will cause the DAPM context to be powered up.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
We need to make sure that the control's cached value is initialized to the same
value as the control's widget->on_val. Otherwise updates might be lost.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
snd_soc_dapm_new_widgets() works on the ASoC card as a whole not on a specific
DAPM context. The DAPM context that is passed as the parameter is only used to
look up the pointer to the card. This patch updates the signature of
snd_soc_dapm_new_widgets() to take the card directly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The current calls to dapm_mark_dirty() in snd_soc_dapm_add_path() are on a path
that is only reached if the sink widget is either a mixer or a mux. Move the
calls further up so they are called for all widget types.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Ensure that the recently added path kcontrol list is initialised otherwise
we may crash trying to delete routes that don't have kcontrols.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
Attempting to create the route as part of adding a mux control causes us
to attempt to add the same route twice since we loop over all sources
for the mux after creating the control. Instead do the addition in the
callers.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
|
|
ASoC automatically creates snd_soc_dapm_dai_in and snd_soc_dapm_dai_out
widgets for DAI drivers, and adds them to the list. Later on, ASoC
creates automatic routes between these widgets and a widget with a
stream name.
We look for a snd_soc_dapm_dai_in or snd_soc_dapm_dai_out widget, and
use this to obtain the DAI structure. We then scan all widgets for
any with a stream name refering to either the capture or the playback
stream, and create routes.
If you have both a snd_soc_dapm_dai_in and a snd_soc_dapm_dai_out
referring to the same DAI structure, this ends up creating one set of
routes for the DAI for the snd_soc_dapm_dai_in widget, and a duplicated
set of routes for the snd_soc_dapm_dai_out widget.
Fix this by checking that the stream name for the widget matches the
DAI widget name.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Some devices have the problem that if a internal audio signal source is disabled
the output of the source becomes undefined or goes to a undesired state (E.g.
DAC output goes to ground instead of VMID). In this case it is necessary, in
order to avoid unwanted clicks and pops, to disable any mixer input the signal
feeds into or to active a mute control along the path to the output. Often it is
still desirable to expose the same mixer input control to userspace, so cerain
paths can sill be disabled manually. This means we can not use conventional DAPM
to manage the mixer input control. This patch implements a method for letting
DAPM overwrite the state of a userspace visible control. I.e. DAPM will disable
the control if the path on which the control sits becomes inactive. Userspace
will then only see a cached copy of the controls state. Once DAPM powers the
path up again it will sync the userspace setting with the hardware and give
control back to userspace.
To implement this a new widget type is introduced. One widget of this type will
be created for each DAPM kcontrol which has the auto-disable feature enabled.
For each path that is controlled by the kcontrol the widget will be connected to
the source of that path. The new widget type behaves like a supply widget,
which means it will power up if one of its sinks are powered up and will only
power down if all of its sinks are powered down. In order to only have the mixer
input enabled when the source signal is valid the new widget type will be
disabled before all other widget types and only be enabled after all other
widget types.
E.g. consider the following simplified example. A DAC is connected to a mixer
and the mixer has a control to enable or disable the signal from the DAC.
+-------+
+-----+ | |
| DAC |-----[Ctrl]-| Mixer |
+-----+ : | |
| : +-------+
| :
+-------------+
| Ctrl widget |
+-------------+
If the control has the auto-disable feature enabled we'll create a widget for
the control. This widget is connected to the DAC as it is the source for the
mixer input. If the DAC powers up the control widget powers up and if the DAC
powers down the control widget is powered down. As long as the control widget
is powered down the hardware input control is kept disabled and if it is enabled
userspace can freely change the control's state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
list_first_entry() will always return a valid pointer, even if the list is
empty. So the check whether path is NULL will always be false. So we end up
calling dapm_create_or_share_mixmux_kcontrol() with a path struct that points
right in the middle of the widget struct and by trying to modify the path the
widgets memory will become corrupted. Fix this by using list_emtpy() to check if
the widget doesn't have any paths.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
|
|
When calling krealloc for the kcontrol data the items in the path list that
point back to the head of the list will now point to freed memory, which causes
the list to become corrupted. To fix this, instead of resizing the whole data
struct, only resize the widget list.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
snd_soc_cnew() can return NULL, so we should check the result before trying to
use it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There is a typo here so we end up using the old freed pointer instead of
the newly allocated one. (If the "n" is zero then the code works,
obviously).
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Wait with updating the widgets power field until the changes are actually
written to the hardware in dapm_seq_run_coalesced(). This will allow us to query
the current hardware state between calling dapm_power_one_widget() and actually
writing the new power state to hardware.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
snd_soc_dapm_add_path() is similar to snd_soc_dapm_add_route() except that it
expects the pointer to the source and sink widgets instead of their names. This
allows us to simplify the case where we already have a pointer to widgets. (E.g.
as we have in snd_soc_dapm_link_dai_widgets()). snd_soc_dapm_add_route() will be
updated to just look up the widget and then use snd_soc_dapm_add_path() to
handle everything else.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Currently the DAPM code is limited to only setting or clearing a single bit in a
register to power a widget up or down. This patch extends the DAPM code to be
more flexible in that regard and allow widgets to use arbitrary values to be
used to put a widget in either on or off state.
Since the snd_soc_dapm_widget struct already contains a on_val and off_val field
no additional fields need to be added and in fact the invert field can even be
removed. Also the generated code is slightly smaller.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Currently we store for each path which control (if any at all) is associated
with that control. But we are only ever interested in the reverse relationship,
i.e. we want to know all the paths a certain control is associated with. This is
currently implemented by always iterating over all paths. This patch updates the
code to keep a list for each control which contains all the paths that are
associated with that control. This improves the run time of e.g.
soc_dapm_mixer_update_power() and soc_dapm_mux_update_power() from O(n) (with n
being the number of paths for the card) to O(1).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The 'value' field is really per control and not per widget. Currently it is only
used for virtual MUXes, which only have one control per widget. So in that case
there is not so much of a difference between whether it is stored per widget or
per control. Moving the 'value' field from the widget to the control will allow
us to use it also for cases where we have more than one control per widget. E.g.
for mixers with multiple input controls.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
In preparation for adding additional per control data wrap all access to the
widget list in helper functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
