summaryrefslogtreecommitdiffstats
path: root/sound/soc
AgeCommit message (Collapse)Author
2009-09-30ASoC: Clean up WM8974 PLL configurationMark Brown
Don't use a static for WM8974 PLL factors - we don't support more than one device so it won't happen but no sense in leaving the race condition hanging around. Also, pre_div is a single bit and it's a bit simpler if we move the handling of the factor of 4 in the output into the coefficient setup. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-30ASoC: DaVinci: McASP FIFO related updatesChaithrika U S
The DMA params for McASP with FIFO has been updated so that it works for various FIFO levels. A member- 'fifo_level' has been added to the DMA params data structure. The fifo_level can be adjusted by the tx[rx]_numevt platform data. This is relevant only for DA8xx/OMAP-L1xx platforms. This implementation has been tested for numevt values 1, 2, 4, 8. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-25ASoC: pxa-ssp increase max_channels to 8Graeme Gregory
When running in TDM mode there can be more than 2 channels used. Datasheet has figures for upto 8 channels so increase max_channels on all SSP interfaces to this figure. Signed-off-by: Graeme Gregory <dp@xora.org.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-23Merge branch 'for-2.6.32' into for-2.6.33Mark Brown
2009-09-23ASoC: DaVinci: Correct McASP FIFO initializationChaithrika U S
McASP write FIFO registers should be modified for playback and read FIFO registers for capture. Check the PCM mode before manipulating the FIFO registers. Currently, irrespective of playback/capture both the FIFOs are enabled or disbaled. This resulted in errors in audio loopback mode. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-23ASoC: Davinci: Fix race with cpu_dai->dma_dataTroy Kisky
This patch removes references to cpu_dai->dma_data. It makes struct davinci_pcm_dma_params part of struct davinci_mcbsp_dev or struct davinci_audio_dev. It removes the unused name variable from davinci_pcm_dma_params. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-23ASoC: DaVinci: Fix divide by zero error during 1st executionTroy Kisky
When both playback and capture stream were open davinci_i2s_hw_params was setting parameters for the wrong stream. The fix for davinci_i2s_hw_params is sufficient, but it looks like a race still happens in davici_pcm_open. This patch also makes the race smaller but the next patch provides a better fix. Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-23Merge branch 'fix/asoc' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 * 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: ASoC: wm8753: fix mapping when MONOMIX is set to Stereo ASoC: some minor changes for AD1836 and AD1938 codec drivers ASoC: DaVinci: Fixes to McASP configuration ASoC: Blackfin I2S: fix resuming when device hasn't been used ASoC: Blackfin I2S: add lost platform_device parameter to resume function ASoC: fix typos in Blackfin headers ASoC: bf5xx-sport: the irq save/restore funcs take an unsigned long ASoC: Blackfin AC97: add a few missing multichannel define handling
2009-09-23ASoC: Blackfin: fix inverted handling of SPORT0 on PORT F/GCliff Cai
Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-23ASoC: Blackfin I2S: use dai state rather than local counterBarry Song
Since the active field of the dai already tells us the stream activity, the local counter variable is redundant and can be replaced. Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-21ASoC: wm8753: fix mapping when MONOMIX is set to StereoPhil Vandry
When MONOMIX is set to Stereo, Left PGA was not powered on but should be. Add a mapping from Capture Left Mux to Capture Left Mixer to fix the issue. Signed-off-by: Phil Vandry <vandry@TZoNE.ORG> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-21ASoC: some minor changes for AD1836 and AD1938 codec driversBarry Song
1. delete redundant assignment to bus field in spi_driver structure 2. fix lost assignment to set_bias_level entry in ad1938 codec dai 3. change spi driver name of ad1836 from "ad1836-spi" to "ad1836" Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-21trivial: remove unnecessary semicolonsJoe Perches
Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-09-21Merge branch 'upstream/wm8711' into for-2.6.33Mark Brown
2009-09-21ASoC: Convert soc-cache to use C99 style initialisers for the tableMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-19ASoC: Support WM8580 based audio subsystem on SMDK64xx machinesjassi brar
New machine driver for WM8580 I2S i/f on SMDK64XX. By default SoC-Slave is set and WM8580 is configured to use it's PLLA to generate clocks from a 12MHz crystal attached to WM8580. [Added dependency on BROKEN since the IISv4 interface hasn't been merged yet, fixed the PLL API usage and removed the disabling of the PLL in the hw_free function since that'll break simultaneous playback and record -- broonie.] Signed-off-by: Jassi <jassi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-18Merge branch 'davinci-for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci * 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (62 commits) DaVinci: DM646x - platform changes for vpif capture and display drivers davinci: DM355 - platform changes for vpfe capture davinci: DM644x platform changes for vpfe capture davinci: audio: move tlv320aic33 i2c setup into board files DaVinci: EDMA: Adding 2 new APIs for allocating/freeing PARAMs DaVinci: DM365: Adding entries for DM365 IRQ's DaVinci: DM355: Adding PINMUX entries for DM355 Display davinci: Handle pinmux conflict between mmc/sd and nor flash davinci: Add NOR flash support for da850/omap-l138 davinci: Add NAND flash support for DA850/OMAP-L138 davinci: Add MMC/SD support for da850/omap-l138 davinci: Add platform support for da850/omap-l138 GLCD davinci: Macro to convert GPIO signal to GPIO pin number davinci: Audio support for DA850/OMAP-L138 EVM davinci: Audio support for DA830 EVM davinci: Correct the number of GPIO pins for da850/omap-l138 davinci: Configure MDIO pins for EMAC DaVinci: DM365: Add Support for new Revision of silicon DaVinci: DM365: Fix Compilation issue due to PINMUX entry DaVinci: EDMA: Updating default queue handling ...
2009-09-18Merge branch 'for-2.6.32' into for-2.6.33Mark Brown
2009-09-18ASoC: Return correct codec clock in s3c64xx-i2sJassi
Instead of always returnig pointer to the 'audio-bus' clock, check which clock is used to generate internal clocks and then return it's pointer. Signed-off-by: Jassi <jassi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-18ASoC: DaVinci: Fixes to McASP configurationChaithrika U S
McASP register settings are not correct for DSP mode of operation. There is a channel swap initally. This patch provides fixes to the register values for proper working. Tested on DA830/OMAP-L137 EVM, DM6467 EVM. Signed-off-by: Chaithrika U S <chaithrika@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-18ASoC: Blackfin I2S: fix resuming when device hasn't been usedCliff Cai
If the sound system hasn't been utilized yet and we suspend, then we attempt to save/restore using state that doesn't exist. So use a global handle instead to reconfigure properly. Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-17Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: ALSA: hda - Fix MSI GX620 mixer ASoC: remove unused #include <linux/version.h> ASoC: S3C lrsync function made to work with IRQs disabled. ALSA: hda - Fix Dell S14 pin setup ALSA: hda - Fix IDT92HD83* codec setup ASoC: Fix display of stream name in DAPM debugfs ALSA: hda - Add support for HP dv6 ALSA: hda - Fix HP/line-out initialization with IDT/STAC codecs ALSA: hda - Set default GPIO for IDT92HD71bxx ALSA: hda - Set default GPIO for STAC/IDT codecs ASoC: Clean up error handling in MPC5200 DMA setup ALSA: hda - Add missing model=auto entry for ALC269
2009-09-17Merge branch 'fix/asoc' into for-linusTakashi Iwai
* fix/asoc: ASoC: remove unused #include <linux/version.h> ASoC: S3C lrsync function made to work with IRQs disabled. ASoC: Fix display of stream name in DAPM debugfs ASoC: Clean up error handling in MPC5200 DMA setup
2009-09-17ASoC: Blackfin I2S: add lost platform_device parameter to resume functionBarry Song
Commit dc7d7b830ee1 trimmed the platform_device parameter from all of the suspend functions, but it also accidentally removed it from the resume function in the Blackfin I2S driver. So restore it. Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-17ASoC: fix typos in Blackfin headersBarry Song
Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-17ASoC: bf5xx-sport: the irq save/restore funcs take an unsigned longMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-17ASoC: Blackfin AC97: add a few missing multichannel define handlingCliff Cai
Somewhere along the line, most of SND_BF5XX_MULTICHAN_SUPPORT handling was merged, but two places were missed (the probe/resume functions). Restore handling of this option so it gets initialized properly. Signed-off-by: Cliff Cai <cliff.cai@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-16ASoC: remove unused #include <linux/version.h>Huang Weiyi
Remove unused #include <linux/version.h>('s) in sound/soc/codecs/ad1836.c sound/soc/codecs/ad1938.c sound/soc/codecs/wm8974.c Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-16ASoC: Add S3C64xx IIS CDCLK source selectionMark Brown
CDCLK can either be an output generated by the CPU, intended for use as the CODEC master clock, or an input (probably from the CODEC) providing a master clock for the IIS block. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-15ASoC: Davinci: Add audio codec support for DM365 EVMMiguel Aguilar
This patch enables tlv320aic3101 support on DM365 EVM and it was tested on DM365 EVM rev c. Note: this patch was created based on temp/asoc branch. Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-15ASoC: use set_channel_map api to reorder channels for AD1938 and AD1836Barry Song
Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-15ASoC: S3C I2S LRCLK polarity option.Jassi
1) Explicitly set LRCLK polarity for I2S Vs LSM/MSB modes. 2) Convert from numerical to bit-field values for BCLK selection. 3) Use proper error checking for return value from clk_get Signed-off-by: Jassi <jassi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-15ASoC: S3C lrsync function made to work with IRQs disabled.Jassi
s3c2412_snd_lrsync() maybe reached with IRQs disabled and if LRCLK is dead due to improper initialization of CPU or CODEC, the system gets stuck in the loop because jiffies may never get updated. Implemented counter based wait mechanism for atleast the same timeout period. Signed-off-by: Jassi <jassi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-14Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-armLinus Torvalds
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (257 commits) [ARM] Update mach-types ARM: 5636/1: Move vendor enum to AMBA include ARM: Fix pfn_valid() for sparse memory [ARM] orion5x: Add LaCie NAS 2Big Network support [ARM] pxa/sharpsl_pm: zaurus c3000 aka spitz: fix resume ARM: 5686/1: at91: Correct AC97 reset line in at91sam9263ek board ARM: 5640/1: This patch modifies the support of AC97 on the at91sam9263 ek board ARM: 5689/1: Update default config of HP Jornada 700-series machines ARM: 5691/1: fix cache aliasing issues between kmap() and kmap_atomic() with highmem ARM: 5688/1: ks8695_serial: disable_irq() lockup ARM: 5687/1: fix an oops with highmem ARM: 5684/1: Add nuc960 platform to w90x900 ARM: 5683/1: Add nuc950 platform to w90x900 ARM: 5682/1: Add cpu.c and dev.c and modify some files of w90p910 platform ARM: 5626/1: add suspend/resume functions to amba-pl011 serial driver ARM: 5625/1: fix hard coded 4K resource size in amba bus detection MMC: MMCI: convert realview MMC to use gpiolib ARM: 5685/1: Make MMCI driver compile without gpiolib ARM: implement highpte ARM: Show FIQ in /proc/interrupts on CONFIG_FIQ ... Fix up trivial conflict in arch/arm/kernel/signal.c. It was due to the TIF_NOTIFY_RESUME addition in commit d0420c83f ("KEYS: Extend TIF_NOTIFY_RESUME to (almost) all architectures") and follow-ups.
2009-09-14ASoC: Fix display of stream name in DAPM debugfsMark Brown
Also display streams all the time while we're here. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-13ASoC: Provide API for reordering channelsBarry Song
The patch adds an interface to set the relationship between audio channel number and slot number. The interface should be really useful because audio channel n doesn't always use slot n in all platforms. And for some devices, the relationship even can change with sound mode switch in 2.1,3.1,4.1,5.1,6.1,7.1 etc. Signed-off-by: Barry Song <21cnbao@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-12ASoC: Clean up error handling in MPC5200 DMA setupJulia Lawall
Error handling code following a kzalloc should free the allocated data. Error handling code following an ioremap should iounmap the allocated data. The semantic match that finds the first problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; statement S; expression E; identifier f,f1,l; position p1,p2; expression *ptr != NULL; @@ x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...); ... if (x == NULL) S <... when != x when != if (...) { <+...x...+> } ( x->f1 = E | (x->f1 == NULL || ...) | f(...,x->f1,...) ) ...> ( return \(0\|<+...x...+>\|ptr\); | return@p2 ...; ) @script:python@ p1 << r.p1; p2 << r.p2; @@ print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-12Merge branch 'master' into develRussell King
2009-09-12Merge branch 'devel-stable' into develRussell King
Conflicts: MAINTAINERS arch/arm/mm/fault.c
2009-09-12Merge branches 'arm', 'at91', 'bcmring', 'ep93xx', 'mach-types', 'misc' and ↵Russell King
'w90x900' into devel
2009-09-10Merge branch 'topic/asoc' into for-linusTakashi Iwai
* topic/asoc: (226 commits) ASoC: au1x: PSC-AC97 bugfixes ASoC: Fix WM835x Out4 capture enumeration ASoC: Remove unuused hw_read_t ASoC: fix pxa2xx-ac97.c breakage ASoC: Fully specify DC servo bits to update in wm_hubs ASoC: Debugged improper setting of PLL fields in WM8580 driver ASoC: new board driver to connect bfin-5xx with ad1836 codec ASoC: OMAP: Add functionality to set CLKR and FSR sources in McBSP DAI ASoC: davinci: i2c device creation moved into board files ASoC: Don't reconfigure WM8350 FLL if not needed ASoC: Fix s3c-i2s-v2 build ASoC: Make platform data optional for TLV320AIC3x ASoC: Add S3C24xx dependencies for Simtec machines ASoC: SDP3430: Fix TWL GPIO6 pin mux request ASoC: S3C platform: Fix s3c2410_dma_started() called at improper time ARM: OMAP: McBSP: Merge two functions into omap_mcbsp_start/_stop ASoC: OMAP: Fix setup of XCCR and RCCR registers in McBSP DAI OMAP: McBSP: Use textual values in DMA operating mode sysfs files ARM: OMAP: DMA: Add support for DMA channel self linking on OMAP1510 ASoC: Select core DMA when building for S3C64xx ...
2009-09-10ASoC: AK4671: add ak4671 codec driverJoonyoung Shim
The AK4671 is a stereo CODEC with a built-in Microphone-Amplifier, Receiver-Amplifier and Headphone-Amplifier. The datasheet for the ak4671 can find at the following url: http://www.asahi-kasei.co.jp/akm/en/product/ak4671/ak4671_f01e.pdf Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-08ASoC: Allow per-route connectedness checks for suppliesMark Brown
Some chips with complex internal supply (particularly clocking) arragements may have multiple options for some of the supply connections. Since these don't affect user-visible audio routing the expectation would be that they would be managed automatically by one of the drivers. Support these users by allowing routes to have a connected function which is queried before the connectedness of the path is checked as normal. Currently this is only done for supplies, other widgets could be supported but are not currently since the expectation for them is that audio routing will be under the control of userspace. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-08ASoC: au1x: PSC-AC97 bugfixesManuel Lauss
This patch fixes the following bugs: - only reprogram bitdepth if it has changed since last call to hw_params. - add locking inside ac97_read/write functions: When reprogramming sample depth, the ac97 unit has to be disabled, which should not be done in the middle of codec register accesses. - retry timed-out codec register accesses. - wait for status bits to set/clear when starting/stopping various functional blocks; very important after reenabling AC97 unit else sound may be distorted (e.g. high-pitch noise in 1kHz sine wave). - clear fifos before/after starting/stopping RX/TX. - longer timeouts waiting for PSC/AC97 ready after cold reset with certain codecs this can take ridiculous amounts of time. Run-tested on various Au1200 platforms with various codecs. Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-07ASoC: Fix WM835x Out4 capture enumerationMark Brown
It's the 8th enum of a zero indexed array. This is why I don't let new drivers use these arrays of enums... Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@kernel.org
2009-09-07ASoC: Factor out I2C 8 bit address 8 bit data I/OJoonyoung Shim
This patch is for the AK4671 codec driver using this format. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-05ASoC: Add source argument to PLL configurationMark Brown
More and more devices feature PLLs and FLLs with the ability to select between multiple input clocks. In order to better support these devices a new argument, source, has been added to the set_pll() configuration API. Using set_clkdiv() is often difficult due to the need to stop the PLL/FLL before any reconfiguration can be done. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-02ASoC: Fully specify DC servo bits to update in wm_hubsMark Brown
Avoids potential issues if we read back unexpected values during a read/modify/write cycle. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-01ASoC: Debugged improper setting of PLL fields in WM8580 driverjassi brar
Bug was caught while trying to use WM8580 as I2S master on SMDK. Symptoms were lesser LRCLK read by CRO(41.02 instead of 44.1 KHz) Solved by referring to WM8580A manual and setting mask value correctly and making the code to not touch 'reserved' bits of PLL4 register. Signed-off-by: Jassi <jassi.brar@samsung.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2009-09-01ASoC: new board driver to connect bfin-5xx with ad1836 codecBarry Song
As discussed, the patch uses the original TDM order without rewriting. For the match between TDM slot number and audio channel number, a new API need be added. Signed-off-by: Barry Song <21cnbao@gmail.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>