| Age | Commit message (Collapse) | Author |
|---|
|
The card callback will get called for each DAPM context in the card so it
can be useful for it to know which device is currently undergoing a
transition.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
No functional changes but much less indentation.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
It's redundant now thanks to the use of the generic trace infrastructure.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
More with the legibility.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
If the only widgets active within a CODEC are supplies and micbiases we
are not passing audio, we are probably just doing microphone detection.
This will not generally require either fully accurate reference voltages
or much power so
If this turns out to be unsuitable for some systems we can provide a
facility to override this decision.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Rather than a simple flag to say if we want the DAPM context to be at full
power specify the target bias state. This should have no current effect
but is a bit more direct and so makes it easier to change our decisions
about the which bias state to go into in future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Allow more dynamic management of the device clocking by allowing BCLK to
be calculated when we set SYSCLK. This means that if the system is idle
when hw_params() runs then we don't try to use the SYSCLK used in that case
to set up the BCLK dividers, we can instead wait until a later point such
as bias level configuration. This makes it easier to manage low power modes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Avoids issues if someone does a read followed by restore and doesn't mask
out only the bits being updated.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
When the FLL locks on the WM8915 an interrupt is generated. For safety
error out if we don't get that interrupt when the IRQ output of the
WM8915 is hooked up. Since we *really* expect an interrupt but the
threaded IRQ handler may take a bit longer than expected to get
scheduled also dramatically increase the delay in this case.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6 into for-3.0
|
|
We should only call ssc_free() when ssc_request() succeeds or bad
things will happen.
Signed-off-by: Joachim Eastwood <joachim.eastwood@jotron.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
We only need to increase the detection rate to maximum if we're monitoring
for button presses as the response times needed for user interaction there
are much lower.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Revision 2 of the Speyside platform supplies a 32kHz clock on MCLK2 rather
than MCLK1.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
DCVDD and MICVDD are intended to be (and almost always are) generated by
on-board LDOs which are transparently controlled by the driver so we
shouldn't really be requesting them from the regulator API. If the driver
is updated to support external supply of these then we will need to change
the way we handle this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
This goto is after the call to clk_get, so it should go to the label that
includes a call to clk_put.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Really this should be something the IRQ core can cope with for us but since
it doesn't currently do so (at least for threaded interrupts like this) do
so in the driver. This allows us to run with interrupt controllers that
only support edge triggered interrupts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
|
|
Current implementation set max98095->sysclk/max98088->sysclk to freq twice.
Set it once is enough, this patch removes the first assignment in case
we may set invalid clock frequency to max98095->sysclk/max98088->sysclk.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Peter Hsiang <peter.hsiang@maxim-ic.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
ARM: 6945/1: Add unwinding support for division functions
ARM: kill pmd_off()
ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks
ARM: 6943/1: mm: use TTBR1 instead of reserved context ID
ARM: 6942/1: mm: make TTBR1 always point to swapper_pg_dir on ARMv6/7
ARM: 6941/1: cache: ensure MVA is cacheline aligned in flush_kern_dcache_area
ARM: add sendmmsg syscall
ARM: 6863/1: allow hotplug on msm
ARM: 6832/1: mmci: support for ST-Ericsson db8500v2
ARM: 6830/1: mach-ux500: force PrimeCell revisions
ARM: 6829/1: amba: make hardcoded periphid override hardware
ARM: 6828/1: mach-ux500: delete SSP PrimeCell ID
ARM: 6827/1: mach-netx: delete hardcoded periphid
ARM: 6940/1: fiq: Briefly document driver responsibilities for suspend/resume
ARM: 6938/1: fiq: Refactor {get,set}_fiq_regs() for Thumb-2
ARM: 6914/1: sparsemem: fix highmem detection when using SPARSEMEM
ARM: 6913/1: sparsemem: allow pfn_valid to be overridden when using SPARSEMEM
at91: drop at572d940hf support
at91rm9200: introduce at91rm9200_set_type to specficy cpu package
at91: drop boot_params and PLAT_PHYS_OFFSET
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (26 commits)
ASoC: Fix power down for widgetless per-card DAPM context case
ASoC: wm1250-ev1: Define "WM1250 Output" with SND_SOC_DAPM_OUTPUT
ASoC: Remove duplicate linux/delay.h inclusion.
ASoC: sam9g20_wm8731: use the proper SYSCKL value
ASoC: wm8731: fix wm8731_check_osc() connected condition
ALSA: hda - Reorganize controller quriks with bit flags
ALSA: hda - Use snd_printd() in snd_hda_parse_pin_def_config()
ALSA: core: remove unused variables.
ALSA: HDA: Increase MAX_HDMI_PINS
ALSA: PCM - Don't check DMA time-out too shortly
MAINTAINERS: add FireWire audio maintainer
ALSA: usb-audio: more control quirks for M-Audio FastTrack devices
ALSA: usb-audio: add new quirk type QUIRK_AUDIO_STANDARD_MIXER
ALSA: usb-audio: export snd_usb_feature_unit_ctl
ALSA: usb-audio: rework add_control_to_empty()
ALSA: usb-audio: move assignment of chip->ctrl_intf
ALSA: hda - Use model=auto for Lenovo G555
ALSA: HDA: Unify HDMI hotplug handling.
ALSA: hda - Force AD1988_6STACK_DIG for Asus M3N-HT Deluxe
ASoC: core - remove superfluous new line.
...
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
We want the default state of the HP_MUTE signal to be asserted, so that
the headphones are muted before the first audio playback. Without this,
the headphones are left unmuted until shortly after the first audio
playback completes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Run the data through cpu_to_be16() so it's at least clear what we're up to.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Commit af46800 ("ASoC: Implement mux control sharing") introduced
function dapm_is_shared_kcontrol.
When this function returns true, the naming of DAPM controls is derived
from the kcontrol_new. Otherwise, the name comes from the widget (and
possibly a widget's naming prefix).
A bug in the implementation of dapm_is_shared_kcontrol made it return 1
in all cases. Hence, that commit caused a change in control naming for
all controls instead of just shared controls.
Specifically, a control is always considered shared because it is always
compared against itself. Solve this by never comparing against the widget
containing the control being created.
Equally, controls should never be shared between DAPM contexts; when the
same codec is instantiated multiple times, the same kcontrol_new will be
used. However, the control should no be shared between the multiple
instances.
I tested that with the Tegra WM8903 driver:
* Shared is now mostly 0 as expected, and sometimes 1.
* The expected controls are still generated after this change.
However, I don't have any systems that have a widget/control naming
prefix, so I can't test that aspect.
Thanks for Jarkko Nikula for pointing out how to fix this.
Reported-by: Liam Girdwood <lrg@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (57 commits)
regulator: Fix 88pm8607.c printk format warning
input: Add support for Qualcomm PMIC8XXX power key
input: Add Qualcomm pm8xxx keypad controller driver
mfd: Add omap-usbhs runtime PM support
mfd: Fix ASIC3 SD Host Controller Configuration size
mfd: Fix omap_usbhs_alloc_children error handling
mfd: Fix omap usbhs crash when rmmoding ehci or ohci
mfd: Add ASIC3 LED support
leds: Add ASIC3 LED support
mfd: Update twl4030-code maintainer e-mail address
mfd: Correct the name and bitmask for ab8500-gpadc BTempPullUp
mfd: Add manual ab8500-gpadc batt temp activation for AB8500 3.0
mfd: Provide ab8500-core enumerators for chip cuts
mfd: Check twl4030-power remove script error condition after i2cwrite
mfd: Fix twl6030 irq definitions
mfd: Add phoenix lite (twl6025) support to twl6030
mfd: Avoid to use constraint name in 88pm860x regulator driver
mfd: Remove checking on max8925 regulator[0]
mfd: Remove unused parameter from 88pm860x API
mfd: Avoid to allocate 88pm860x static platform data
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
OMAP3: PM: Boot message is not an error, and not helpful, remove it
OMAP3: cpuidle: change the power domains modes determination logic
OMAP3: cpuidle: code rework for improved readability
OMAP3: cpuidle: re-organize the C-states data
OMAP3: clean-up mach specific cpuidle data structures
OMAP3 cpuidle: remove useless SDP specific timings
usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
usb: otg: OMAP4430: Fixing the omap4430_phy_init function
usb: musb: am35x: fix compile error when building am35x
usb: musb: OMAP4430: Power down the PHY during board init
omap: drop board-igep0030.c
omap: igep0020: add support for IGEP3
omap: igep0020: minor refactoring
omap: igep0020: name refactoring for future merge with IGEP3
omap: Remove support for omap2evm
arm: omap2plus: GPIO cleanup
omap: musb: introduce default board config
omap: move detection of NAND CS to common-board-devices
omap: use common initialization for PMIC i2c bus
omap: consolidate touch screen initialization among different boards
...
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Cc: Matti Aaltonen <matti.j.aaltonen@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Commit 52ba67b ("ASoC: Force all DAPM contexts into the same bias state")
powers up all the DAPM contexts in a card if any DAPM context becomes
active. Unfortunately power down newer happens if per-card DAPM context
doesn't have any widgets.
Reason for this is that power state of per-card DAPM context without
widgets is never cleared and thus all the DAPM contexts remain permanently
active. Test for widgetless calling DAPM context in dapm_power_widgets()
doesn't work for per-card DAPM context since power change is never
originating from widgetless per-card DAPM context.
Fix this by pre-clearing power state flag of non-codec DAPM context at the
beginning of power sequence.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Codec output pin should be defined with SND_SOC_DAPM_OUTPUT.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
It's enough to include linux/delay.h just once in
sound/soc/codecs/wm8915.c, so remove the duplicate.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
at91sam9g20 is providing master clock to wm8731: not using a crystal but an
external MCLK. We can avoid conflict and save power using WM8731_SYSCLK_MCLK as
we do not need oscillator to be powered.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The crystal oscillator is only enabled if the WM8731_SYSCLK_XTAL master clock
is specified. Fix the connected() struct snd_soc_dapm_route function to take
this into account. Oscillator is not enabled on machine that need it otherwise.
Machine drivers have to make sure that they use the proper SYSCLK value.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
We do not have to free a resource that is not allocated yet.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
For cards that have two or more DAIs, snd_soc_resume's loop over all
DAIs ends up calling schedule_work(deferred_resume_work) once per DAI.
Since this is the same work item each time, the 2nd and subsequent
calls return 0 (work item already queued), and trigger the dev_err
message below stating that a work item may have been lost.
Solve this by adjusting the loop to simply calculate whether to run the
resume work immediately or defer it, and then call schedule work (or not)
one time based on that.
Note: This has not been tested in mainline, but only in chromeos-2.6.38;
mainline doesn't support suspend/resume on Tegra, nor does the mainline
Tegra ASoC driver contain multiple DAIs. It has been compile-checked in
mainline.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The comment does not reflect reality anymore since the multi-component
monster patch landed. Things are matched by names now, and not by
exporting and referencing a struct. Fix it to avoid confusion.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
