summaryrefslogtreecommitdiffstats
path: root/sound/soc
AgeCommit message (Collapse)Author
2014-07-25ASoC: fsl_sai: Improve enable flow in fsl_sai_trigger()Nicolin Chen
The previous enable flow: 1, Enable TE&RE (SAI starts to consume tx FIFO and feed rx FIFO) 2, Mask IRQ of Tx/Rx to enable its interrupt. 3, Enable DMA request of Tx/Rx. As this flow would enable DMA request later than TERE, the Tx FIFO would be easily emptied into underrun while Rx FIFO would be easily stuffed into overrun due to the delayed DMA transfering. This issue happened merely occational before the patch 'ASoC: fsl_sai: Reset FIFOs after disabling TE/RE' because there were useless data remaining in the FIFO for the gap. However, it manifested after FIFO reset's implemented. After this patch, the new flow: 1, Enable DMA request of Tx/Rx. 2, Enable TE&RE (SAI starts to consume tx FIFO and feed rx FIFO) 3, Mask IRQ of Tx/Rx to enable its interrupt. Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-25ASoC: fsl_sai: Don't reset FIFO until TE/RE bit is unsetNicolin Chen
TE/RE bit of T/RCSR will remain set untill the current frame is physically finished. The FIFO reset operation should wait this bit's totally cleared rather than ignoring its status which might cause TE/RE disabling failed. This patch adds delay and timeout to wait for its completion before FIFO reset. Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-25ASoC: fsl_sai: Reduce race condition during TE/RE enablingNicolin Chen
For trigger start, we don't need to check if it's the first time to enable TE/RE or second time. It doesn't hurt to enable them any way, which in the meantime can reduce race condition for TE/RE enabling. For trigger stop, we will definitely clear FRDE of current direction. Thus the driver only needs to read the opposite one's. Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-25ASoC: rsnd: fixup dai remove callback operationKuninori Morimoto
rsnd driver is using SSI/SRC/DVC which are using "mod" base operation. These "mod" are supporting "probe" and "remove" callbacks. Current rsnd_probe should call "remove" if "probe" was failed, since "probe" might be having DMAEngine handle. Some mod's "remove" callback might be called without calling "probe", but it is no problem. because "remove" do nothing in such case. So, all mod's "remove" should be called when error case of rsnd_probe() and rsnd_remove(). Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-25ASoC: tlv320aic31xx: Add text in Kconfig so the codec can be used with ↵Peter Ujfalusi
simple-card In order to show the option under 'CODEC drivers' we need to have text in Kconfig. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-25ASoC: tlv320aic31xx: Add dependency for I2C and select REGMAP_I2C in KconfigPeter Ujfalusi
The codec can be configured via I2C and using regmap_i2c. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-22ASoC: arizona: Disable AIF TX/RX before configuring itRichard Fitzgerald
Changes to the AIF configuration registers only take effect when the AIF is disabled. If the configuration is being changed from the previous setup, temporarily disable the AIF. Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com> Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-22ASoC: wm8997: Set symmetric samplebits on AIFsRichard Fitzgerald
Different playback and capture bits-per-sample are not supported on the AIFs Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-22ASoC: wm5102: Set symmetric samplebits on AIFsRichard Fitzgerald
Different playback and capture bits-per-sample are not supported on the AIFs Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-22ASoC: wm5110: Set symmetric samplebits on AIFsRichard Fitzgerald
Different playback and capture bits-per-sample are not supported on the AIFs Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-22ASoC: rsnd: add missing src/dst_addr_width for DMAEngineKuninori Morimoto
Renesas new DMAEngine driver requests src/dst_addr_width Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-22ASoC: Add function to register component controlsLars-Peter Clausen
We have now everything in place to actual let a component register controls. Add a function which allows to do so. Also update snd_soc_add_codec_controls() and snd_soc_platform_controls() to use this new function internally. And while we are at it also change the num_controls parameter of those two functions from int to unsigned int. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-22ASoC: Move card field form platform/codec to componentLars-Peter Clausen
Both the snd_soc_codec and snd_soc_platform struct do have a pointer to the parent card and both handle this pointer in mostly the same way. This patch moves the card field to the component level which will allow further code consolidation between platforms and CODECS. Since there are only a handful of users of the snd_soc_codec struct's card field (and none of the snd_soc_platform's) these are update in this patch as well, which allows it to be removed from the snd_soc_codec struct. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-22ASoC: tegra: Replace instances of rtd->codec->card with rtd->cardLars-Peter Clausen
No need to go via the CODEC to get a pointer to the card. This will help to eventually remove the card field from the snd_soc_codec struct. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-22ASoC: Remove per card platform listLars-Peter Clausen
The platform_dev_list was added in commit f0fba2ad1b ("ASoC: multi-component - ASoC Multi-Component Support") and while platforms are added and remove from that list it is otherwise unused. This patch removes it again. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-21ASoC: tas2552: Fix PM sequencingDan Murphy
In the pm suspend/resume it is better to disable the GPIO after the regmap_cache setting calls so that if the call is interrupted the new reg values will be cached and set on resume. Also add pm_runtime_put in the remove call. Signed-off-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-19Merge tag 'samsung-cleanup' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup Merge "Samsung cleanup for v3.17" from Kukjin Kim: Most of them are for exynos SoCs, remove useless codes and update for PMU consolidation. - remove unnecessary header file in mach-exynos/pmu.c - remove unused code in mach-exynos/common.h - remove mach-exynos/regs-pmu.h dependency from PD - remove file path from comment section in mach-exynos - move SYSREG definitions into mach-exynos/regs-sys.h - add mapping PMU base address via DT for PMU cleanup - use staic in mach-exynos/common.h - update Samsung UART config options for low-level debug * tag 'samsung-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: ARM: EXYNOS: Add support for mapping PMU base address via DT ARM: EXYNOS: Remove "linux/bug.h" from pmu.c ARM: EXYNOS: Remove regs-pmu.h header dependency from pm_domain ARM: EXYNOS: Remove file path from comment section ARM: EXYNOS: Move SYSREG definition into sys-reg specific file ARM: EXYNOS: Make exynos machine_ops as static ARM: EXYNOS: Remove unused code in common.h ARM: debug: Update Samsung UART config options + Linux 3.16-rc5 Signed-off-by: Olof Johansson <olof@lixom.net>
2014-07-17Merge remote-tracking branches 'asoc/fix/samsung', 'asoc/fix/sgtl5000', ↵Mark Brown
'asoc/fix/simple' and 'asoc/fix/tlv320aic3x' into asoc-linus
2014-07-17Merge remote-tracking branches 'asoc/fix/fsl-sai', 'asoc/fix/intel', ↵Mark Brown
'asoc/fix/max98090' and 'asoc/fix/s6000' into asoc-linus
2014-07-17Merge remote-tracking branches 'asoc/fix/adau1701', 'asoc/fix/adsp', ↵Mark Brown
'asoc/fix/arizona', 'asoc/fix/blackfin', 'asoc/fix/cs42l56', 'asoc/fix/davinci' and 'asoc/fix/debugfs' into asoc-linus
2014-07-17Merge remote-tracking branch 'asoc/fix/rcar' into asoc-linusMark Brown
2014-07-17Merge remote-tracking branch 'asoc/fix/pcm' into asoc-linusMark Brown
2014-07-17Merge tag 'asoc-v3.16-rc1' into asoc-linusMark Brown
ASoC: Fixes for v3.16 Quite a few build coverage fixes in here among the usual small driver fixes includling the sigmadsp change from Lars - moving the driver to separate modules per bus (which is basically just code motion) avoids issues with some combinations of buses being enabled. # gpg: Signature made Thu 19 Jun 2014 11:57:31 BST using RSA key ID 7EA229BD # gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>" # gpg: aka "Mark Brown <broonie@debian.org>" # gpg: aka "Mark Brown <broonie@kernel.org>" # gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>" # gpg: aka "Mark Brown <broonie@linaro.org>" # gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
2014-07-17ASoC: Fix SOC_DOUBLE_R_SX_TLV volume mixer argumentsBrian Austin
Remove unnecessary bit shifts. Correct min value to match datasheet. Num steps = number of steps between min and max. Reported-by: Ryan Harvey <ryan.harvey@cirrus.com> Signed-off-by: Ryan Harvey <ryan.harvey@cirrus.com> Signed-off-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-17ASoC: cs42l56: Fix stereo channel register assignment for Headphone and ↵Brian Austin
LineOut volume mixers Stereo Headphone and LineOut volume mixers are now attached to HPA+HPB, LOA+LOB. Reported-by: Ryan Harvey <ryan.harvey@cirrus.com> Signed-off-by: Ryan Harvey <ryan.harvey@cirrus.com> Signed-off-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-17ASoC: fsl_sai: Fix incorrect register writing in fsl_sai_isr()Nicolin Chen
In the rx irq handling part, we should clear the flags in RCSR not TCSR. Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-17ASoC: fsl_sai: Reset FIFOs after disabling TE/RENicolin Chen
SAI will not clear their FIFOs after disabling TE/RE. Therfore, the driver should take care the task so as not to let useless data remain in the FIFO. Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-17ASoC: tas2552: Support TI TAS2552 AmplifierDan Murphy
Support the TI TAS2552 Class D amplifier. The TAS2552 is a high efficiency Class-D audio power amplifier with advanced battery current management and an integrated Class-G boost The device constantly measures the current and voltage across the load and provides a digital stream of this information. Signed-off-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-17ASoC: blackfin: use samples to set silenceScott Jiang
The third parameter for snd_pcm_format_set_silence needs the number of samples instead of sample bytes. Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com> Signed-off-by: Mark Brown <broonie@linaro.org> Cc: stable@vger.kernel.org
2014-07-17ASoC: Remove unused 'r' variable from dapm_connect_dai_link_widgets()Lars-Peter Clausen
It was accidentally added in commit 44ba2641 ("ASoC: dapm: Add support for DAI multicodec"). Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16ASoC: Intel: Add Broadwell Machine supportLiam Girdwood
Add support for Broadwell based machines with SST DSP audio. Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com> Signed-off-by: Jie Yang <yang.jie@linux.intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16Merge remote-tracking branch 'asoc/topic/rt286' into HEADMark Brown
2014-07-16ASoC: pcm: Add soc_dai_hw_params helperBenoit Cousson
Add a function helper to factorize the hw_params code. Suggested by Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Benoit Cousson <bcousson@baylibre.com> Tested-by: Lars-Peter Clausen <lars@metafoo.de> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16ASoC: compress: Prevent multicodec for compressed streamBenoit Cousson
Multiple codecs does not make sense in the case of compressed stream. Exit with error if it happens. Signed-off-by: Benoit Cousson <bcousson@baylibre.com> Tested-by: Lars-Peter Clausen <lars@metafoo.de> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16ASoC: dapm: Add support for DAI multicodecBenoit Cousson
Add multicodec support in soc-dapm.c Signed-off-by: Benoit Cousson <bcousson@baylibre.com> Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com> Signed-off-by: Fabien Parent <fparent@baylibre.com> Tested-by: Lars-Peter Clausen <lars@metafoo.de> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16ASoC: pcm: Add support for DAI multicodecBenoit Cousson
Add multicodec support in soc-pcm.c Signed-off-by: Benoit Cousson <bcousson@baylibre.com> Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com> Signed-off-by: Fabien Parent <fparent@baylibre.com> Tested-by: Lars-Peter Clausen <lars@metafoo.de> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16ASoC: core: Add initial support for DAI multicodecBenoit Cousson
DAI link assumes a one to one mapping between CPU DAI and CODEC. In some cases, the same CPU DAI can be connected to several codecs. This is the case for example, if you connect two mono codecs to the same I2S link in order to have a stereo card. The current ASoC implementation does not allow such setup. Add support for DAI links composed of a single CPU DAI and multiple CODECs. Sound cards have to pass the CODECs array in the corresponding DAI link through a new 'snd_soc_dai_link_component' struct. Each CODEC in this array is described in the same manner single CODEC DAIs are (either DT/OF node or codec_name). Multi-codec links are not supported in the case of CODEC to CODEC links. Just print a warning if it happens. Based on an original code done by Misael. Signed-off-by: Benoit Cousson <bcousson@baylibre.com> Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com> Signed-off-by: Fabien Parent <fparent@baylibre.com> Tested-by: Lars-Peter Clausen <lars@metafoo.de> Reviewed-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16Merge remote-tracking branch 'asoc/topic/component' into asoc-multiMark Brown
2014-07-16ASoC: core: add a helper for extended byte controls using TLVOmair Mohammed Abdullah
ALSA supports arbitrary length TLVs for each kcontrol that can be used to pass metadata about the control (e.g. volumes, enum information). The same transport mechanism is now used for arbitrary length data by defining a new helper. Signed-off-by: Omair Mohammed Abdullah <omair.m.abdullah@intel.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16ASoC: Intel: Update FW version readbackJie Yang
Update FW version readback. IPC_GLB_GET_FW_VERSION reads back the ABI version whilst the release version is in the mailbox. Update to use mailbox version for info logging. Signed-off-by: Jie Yang <yang.jie@intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16ASoC: mcasp: don't override bclk divider if it was provided by the machineDaniel Mack
If a machine driver provides an BCLK divider to the McASP driver, skip the automatic calculation. This fixes machines on which the physical sample transport always works in 32 bits, even though not all of them are actually used. snd_soc_params_to_bclk() will fail to address such cases properly. Signed-off-by: Daniel Mack <zonque@gmail.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16ASoC: davinci-mcasp: Use dmaengine based platform driver for AM335x/447xPeter Ujfalusi
Use the edma-pcm with AM335x and AM437x SoCs. Keep using the davinci-pcm for daVinci devices, they can be switched to use the dmaengine based driver later when they are verified to work correctly. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16ASoC: edma-pcm: Add empty functions for !CONFIG_SND_EDMA_SOC buildsPeter Ujfalusi
So drivers mixing with other platform drivers, like davinci-mcasp do not need to fiddle with CONFIG_SND_EDMA_SOC in their code. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16ASoC: edma-pcm: Remove PCM_INFO_BATCH and add PCM_INFO_NO_PERIOD_WAKEUP flagPeter Ujfalusi
The SNDRV_PCM_INFO_BATCH will be added back based on the dmaengine driver's capabilities. Patches for edma dmaengine driver has been prepared to suppress the interrupts. We can add this flag right away and have the benefit of not having interrupts during audio activity when the edma and ASoC patches are in the same tree. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Daniel Mack <daniel@zonque.org> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-16Merge remote-tracking branch 'asoc/fix/davinci' into asoc-davinciMark Brown
2014-07-16ASoC: intel: Cleanup useless ACPI inclusion.Lv Zheng
The sst-haswell-dsp.c is an ACPI independent file, this patch removes ACPI header files for it. Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-14ASoC: samsung: remove unused DMA dataArnd Bergmann
The s3c_dma_client structures and the 'ch' and 'ops' members in s3c_dma_params were only used by the legacy DMA driver and serve no function any more. This removes any reference to them. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-14ASoC: samsung: s3c24xx dmaengine follow-upArnd Bergmann
Commit ae602456e83c92 ("ASoC: samsung: drop support for legacy S3C24XX DMA API") removed the old code for the samsung specific DMA interfaces, now that everybody can use dmaengine. This picks up the few remaining pieces left over by that patch: The most important one is the removal of the dma_data->ops->started() calls in ac97. My understanding is that these are only required for drivers that do not support cyclic transfers, which the new dma engine driver now does, so we can simply remove them. This would also fix at least one bug in the ac97 driver on newer machines, which currently gives us a NULL pointer dereference from trying to call dma_data->ops->started(). Further, we must no longer 'select' S3C2410_DMA, which conflicts with the dmaengine driver. The SND_S3C_DMA symbol is now useless, because it is always selected, so we can remove it and build the dmaengine support unconditionally. Finally, we should not 'select' S3C24XX_DMAC or S3C64XX_PL080, which may have additional dependencies. This replaces it with 'depends on', to be more conservative. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-14ASoC: Intel: mfld: add generic parameter interfaceVinod Koul
This interface will be used by subsequent patches to set/get parameters from DSP Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2014-07-14ASoC: Intel: mfld: add dsp error codesVinod Koul
DSP returns error codes for IPC return so add them in driver Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>