| Age | Commit message (Collapse) | Author |
|---|
|
SST state change should be done under sst_lock
Signed-off-by: Mythri P K <mythri.p.k@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch adds the runtime pm handlers, the driver already has code for
get/put for runtime pm and only these handlers being missing.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It's already done in open/close.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now that manual selection of drivers for audio subsystem components is
preferred AIC23 codec must be selectable in Kconfig to make it possible.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch will optimize the power consumption of rt286.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When using clock gatings to save power, there are some known issues:
1. core clock gating (DCLCGE) must be disabled during D0 and D3 entry
and updating SRAM banks (VDRTCTL0).
2. DSP trunk clock gating (DTCGE) can cause FW crashes, disable it in D0.
To align with the new W/A flow from FW team, we must set VDRTCTL0.D3PGD
to 1 (D3 power gating disabled) at first startup and keep it all the time.
ADSP will be in D0 on first boot by BIOS part of WA. Required delays must
be preserved (waiting for HW to stabilize, after enabling CCG, changing
SRAM PG, D3PG).
D3->D0:
1. Disable core clock gating (VDRTCTL2.DCLCGE = 0)
2. Enable other CG apart from DTCG and DCLCG (VDRTCTL2. DCLCGE and DTCGE = 0)
3. Disable D3PG (VDRTCTL0.D3PGD = 1)
4. Power up necessary SRAM and wait at least for 18 clock cycles for every
bank you have powered up
5. Set D0 state(PMCS.PS = 0), wait for HW
6. Restore MCLK (clkctl.smos, disabled in D3 entry point 4)
7. Stall and reset core, set CSR
8. Enable core clock gating (VDRTCTL2.DCLCGE = 1), delay 50 us
9. Unreset core
10.Load FW, configure PLL and other necessary things
11.Unstall core
Changing SRAM PG during D0:
1. Disable core clock gating (VDRTCTL2.DCLCGE = 0)
2. Set PG mask
3. Wait at least for 18 clock cycles for every bank you have powered up
4. Enable core clock gating, delay 50 us
D0->D3:
1. Disable core clock gating (DCLCGE = 0)
2. Stall and reset core
3. Power down entire SRAM and wait at least for 18 clock cycles for every bank
(Enable SRAM PG (ISRAMPGE = 0x3FF, DSRAMPGE = 0xFFFFF, D3SRAMPGD = 0), remember
about preserving VDRTCTL0.D3PGD = 1)
4. Shutdown PLL, disable MCLK(clkctl.smos = 0), Enable DTCG to save power
5. Set D3 state(PMCS.PS = 3), delay 50 us
6. Enable core clock gating, delay 50 us
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix the following errors:
All error/warnings:
>> sound/soc/intel/sst-haswell-pcm.c:1168:13: error: 'hsw_pcm_prepare' undeclared here (not in a function)
.prepare = hsw_pcm_prepare,
^
>> sound/soc/intel/sst-haswell-pcm.c:1169:14: error: 'hsw_pcm_complete' undeclared here (not in a function)
.complete = hsw_pcm_complete,
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the debug output from IPCD and IPCX when booting fails.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
During FW parsing and loading, block_list_prepare() may
be called for each raw data block copying and this may
made the hsw_block_enable() called mutiple times, which
increase block->users many times. The result of this is
hsw_block_disable() can't power gated the related block
when trying to free the blocks during suspend, and the
power gating status also confused.
Here check the block user status, only calling enable()
for those blocks who has no user yet. Remember that
this works correctlly on current case, where there are
enough SRAM memory so different module won't share a
memory block. For further usage, we may need restructure
the struct sst_mem_block to save the module list who is
using it.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 14621c7e5e72 ("ASoC: Consolidate CPU and CODEC DAI lookup")
consolidated the lookup of CPU DAIs and CODEC DAIs into a single function.
When matching a component by name for CODEC DAIs the code previous to the
patch compared the name in the DAI link table with component->name. For CPU
DAIs the code compared to dev_name(component->dev). The newly introduced
function ended up using the later as well.
For most components dev_name(component->dev) and component->name are the
same. The main notable exception are I2C devices where the driver name and
the device name are concatenated to form the component name. By using
dev_name(component->dev) instead of component->name the patch broke the
matching of I2C CODECs by name.
This patch restores the original behavior by using component->name instead
of dev_name(component->dev). This will be safe even for CPU DAIs since for
CPU DAIs both are the same.
Fixes: 14621c7e5e72 ("ASoC: Consolidate CPU and CODEC DAI lookup")
Reported-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add PM and RTD3 support to the HSW/BDW PCM driver. The PCM driver will
now save DSP context and then power off the DSP when it's not in use.
DSP power and context is then restored when it's next used.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add PM and RTD3 support to the HSW/BDW IPC driver. This patch
saves and restores the DSP context, loads and unloads FW and drops
any pending IPC messages after suspend.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for PM wake, sleep and stall calls to the core HSW/BDW driver.
This includes reworking the reset and boot code and adding new calls
for setting D3/D0 state.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add generic functions to support DSP sleep, wake and stall.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sound/soc/intel/sst-firmware.c:172:29: sparse: symbol 'dw_pdata' was not declared. Should it be static?
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In this way the start code for tx/rx going to be located at the same place.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The AFIFO should not be stopped (or started for that matter) when McASP is
running since it can cause unpredictable issues because we are switching off
AFIFO for the direction which was handling the requests from McASP and was
generating DMA request toward the system DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Follow the sequence described in the TRMs when starting RX.
Write to RXBUF register was not correct and there is no need to release the
RX state machine/Receive frame sync generator twice.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Follow the sequence described in the TRMs when starting TX. This sequence
will make sure that we are not facing with initial channel swap caused by
no data available in McASP for transmit.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The main ASoC source file is getting quite large and the standard ops don't
really have anything to do with the rest of the file so split them out into
a separate file.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
R-Car sound doesn't support PAUSE.
Remove SNDRV_PCM_INFO_PAUSE flags from snd_pcm_hardware info
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
FSI doesn't support PAUSE.
Remove SNDRV_PCM_INFO_PAUSE flags from snd_pcm_hardware info
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
amixer query fails due to it is not readable reigster
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We have calls into the controller so we need to ensure it is being
built.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We can get into an infinite loop if the I2S_CLR register fails to
clear due to a missing break statement, so add that.
Signed-off-by: Jianqun <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
It is for channel to slot mapping, and it is not only for 8 channels mapping,
but also in 2, 4 and 6 channels mapping. If we want to use the 2 channels in
the stereo2 adc path, we need to set the item "2/1/3/4" or "2/3/1/4".
It also adds for stereo channel swap. It can map the sterero channels "L/R"
to "R/L", "L/L" or R/R.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since we are removing the Armada 370 DB audio machine driver to use
the 'simple-card' Device Tree binding, we can no longer select the
CS42L51 codec driver using a Kconfig 'select', and we instead need it
to be user-selectable. Therefore, this commit adds a prompt to make
the CS42L51 I2C codec driver user-selectable.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current block allocation is tied to block type and requestor type. Make the
allocation more generic by removing the struct module parameter and adding
a generic block allocator structure. Also pass in the list that the blocks
have to be added too in order to remove dependence on block requestor type.
ASoC: Intel: update scratch allocator to use generic block allocator
Update the scratch allocator to use the generic block allocator and calculate
total scratch buffer size.
ASoC: Intel: Add call to calculate offsets internally within the DSP.
A call to calculate internal DSP memory addresses used to allocate persistent
and scartch buffers.
ASoC: Intel: Add runtime module support.
Add support for runtime module objects that can be created for every FW
module that is parsed from the FW file. This gives a 1:N mapping between
the FW module from file and the runtime instantiations of that module.
We also need to make sure we remove every module and runtime module when
we unload the FW.
ASoC: Intel: Add DMA firmware loading support
Add support for DMA to load firmware modules to the DSP memory blocks.
Two DMA engines are supported, DesignWare and Intel MID.
ASoC: Intel: Add runtime module lookup API call
Add an API to allow quick lookup of runtime modules based on ID.
ASoC: Intel: Provide streams with dynamic module information
Remove the hard coded module paramaters and provide each module with
dynamically generated buffer information for scratch and persistent
buffers.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current daifmt setting method in simple-card driver is
placed to many places, and using un-readable/confusable method.
This patch adds new asoc_simple_card_parse_daifmt()
and tidyup code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When cpu-dai is the DAI Master (CBM_CFx), it may need some configurations,
set_sysclk() call for eample, for cpu-dai side in the hw_params(), even if
the set_bias_level() has already taken care of the codec-dai side.
So this patch just simply adds an additional condition.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The convention for i2c_device_id name does not need to have company prefix.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to Documentation/CodingStyle - Chapter 14:
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not."
So do it as recommeded.
Cc: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to Documentation/CodingStyle - Chapter 14:
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not."
So do it as recommeded.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to Documentation/CodingStyle - Chapter 14:
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not."
So do it as recommeded.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit f227b88f0fce ("ASoC: core: Add signed register volume control logic")
added support for signed control to the generic volsw control handler.
This makes it possible to use them for the S8 control as well, rather than
having to use a custom control handler implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently we cache the number of input and output paths going to/from a
widget only within a power update sequence. But not in between power update
sequences.
But we know how changes to the DAPM graph affect the number of input (form a
source) and output (to a sink) paths of a widget and only need to
recalculate them if a operation has been performed that might have changed
them.
* Adding/removing or connecting/disconnecting a path means that the for
the source of the path the number of output paths can change and for
the sink the number of input paths can change.
* Connecting/disconnecting a widget has the same effect has connecting/
disconnecting all paths of the widget. So for the widget itself the
number of inputs and outputs can change, for all sinks of the widget
the number of inputs can change and for all sources of the widget the
number of outputs can change.
* Activating/Deactivating a stream can either change the number of
outputs on the sources of the widget associated with the stream or the
number of inputs on the sinks.
Instead of always invalidating all cached numbers of input and output paths
for each power up or down sequence this patch restructures the code to only
invalidate the cached numbers when a operation that might change them has
been performed. This can greatly reduce the number of DAPM power checks for
some very common operations.
Since per DAPM operation typically only either change the number of inputs
or outputs the number of path checks is reduced by at least 50%. The number
of neighbor checks is also reduced about the same percentage, but since the
number of neighbors encountered when walking from sink to source is not the
same as when walking from source to sink the actual numbers will slightly
vary from card to card (e.g. for a mixer we see 1 neighbor when walking from
source to sink, but the number of inputs neighbors when walking from source
to sink).
Bigger improvements can be observed for widgets with multiple connected
inputs and output (e.g. mixers probably being the most widespread form of
this). Previously we had to re-calculate the number of inputs and outputs
on all input and output paths. With this change we only have to re-calculate
the number of outputs on the input path that got changed and the number of
inputs on the output paths.
E.g. imagine the following example:
A --> B ----.
v
M --> N --> Z <-- S <-- R
|
v
X
Widget Z has multiple input paths, if any change was made that cause Z to be
marked as dirty the power state of Z has to be re-computed. This requires to
know the number of inputs and outputs of Z, which requires to know the
number of inputs and outputs of all widgets on all paths from or to Z.
Previously this meant re-computing all inputs and outputs of all the path
going into or out of Z. With this patch in place only paths that actually
have changed need to be re-computed.
If the system is idle (or the part of the system affected by the changed
path) the number of path checks drops to either 0 or 1, regardless of how
large or complex the DAPM context is. 0 if there is no connected sink and no
connected source. 1 if there is either a connected source or sink, but not
both. The number of neighbor checks again will scale accordingly and will be
a constant number that is the number of inputs or outputs of the widget for
which we did the path check.
When loading a state file or switching between different profiles typically
multiple mixer and mux settings are changed, so we see the benefit of this
patch multiplied for these kinds of operations.
Testing with the ADAU1761 shows the following changes in DAPM stats for
changing a single Mixer switch for a Mixer with 5 inputs while the DAPM
context is idle.
Power Path Neighbour
Before: 2 12 30
After: 2 1 2
For the same switch, but with a active playback stream the stat changed are
as follows.
Power Path Neighbour
Before: 10 20 54
After: 10 7 21
Cumulative numbers for switching the audio profile which changes 7 controls
while the system is idle:
Power Path Neighbour
Before: 16 80 170
After: 16 7 23
Cumulative numbers for switching the audio profile which changes 7 controls
while playback is active:
Power Path Neighbour
Before: 51 123 273
After: 51 29 109
Starting (or stopping) the playback stream:
Power Path Neighbour
Before: 34 34 117
After: 34 17 69
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Supply widgets are somewhat special and not all kinds of paths to or from
supply widgets make sense. This patch adds a few sanity checks that errors
out during the path instantiation for those invalid paths. This will prevent
drivers to depend on weird behavior resulting from such paths as well as
will allow the DAPM algorithms to assume that they never see such paths.
This patch adds checks for the following three invalid types of paths:
* A path with a non-supply widget as a source connected to a supply
widget as a sink. Such a path has no effect on either of the two
connected widgets.
* Paths with a connected() callback that have a non-supply widget as the
source. The DAPM algorithm only uses the conneceted() callback for
supply widget power checks. And since it prevents caching of the DAPM
state there is no intention to make it more generic as it has
negative performance implications.
* Paths which connect a supply to a mixer or mux via a control. Controls
are only meant to affect the routing of audio data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The state of endpoint widgets is affected by that card's power state.
Endpoint widgets that do no have the ignore_suspend flag set will be
considered inactive during suspend. So they have to be re-checked and marked
dirty after the card's power state changes. Currently the input and output
widgets are marked dirty instead, this works most of the time since
typically a path from one endpoint to another will go via a input or output
widget. But marking the endpoints dirty is technically more correct and will
also work for odd corner cases.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Supply widgets do not count towards the input and output widgets of their
neighbors and for supply widgets themselves we do not care for the number
of input or output paths. This means that a path that connects to a supply
widget effectively behaves the same as a path that as the weak property set.
This patch adds a new path flag that gets set to true when the path is
connected to at least one supply widget. If a path with the flag set is
encountered in is_connected_{input,output}_ep() is is skipped in the same
way that weak paths are skipped. This slightly brings down the number of
path checks.
Since both the weak and the supply flag are implemented as bitfields which
are stored in the same word there is no runtime overhead due to checking
both rather than just one and also the size of the path struct is not
increased by this patch. Another advantage is that we do not have to handle
supply widgets in is_connected_{input,output}_ep() anymore since it will
never be called for supply widgets. The only exception is from
dapm_widget_power_read_file() where a check is added to special case supply
widgets.
Testing with the ADAU1761, which has a handful of supply widgets, shows the
following changes in the DAPM stats for a playback stream start.
Power Path Neighbour
Before: 34 78 117
After: 34 48 117
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DAPM widgets can be classified into four categories:
* supply: Supply widgets do not affect the power state of their
non-supply widget neighbors and unlike other widgets a
supply widget is not powered up when it is on an active
path, but when at least on of its neighbors is powered up.
* source: A source is a widget that receives data from outside the
DAPM graph or generates data. This can for example be a
microphone, the playback DMA or a signal generator. A source
widget will be considered powered up if there is an active
path to a sink widget.
* sink: A sink is a widget that transmits data to somewhere outside
of the DAPM graph. This can e.g. be a speaker or the capture
DMA. A sink widget will be considered powered up if there is
an active path from a source widget.
* normal: Normal widgets are widgets not covered by the categories
above. A normal widget will be considered powered up if it
is on an active path between a source widget and a sink
widget.
The way the number of input and output paths for a widget is calculated
depends on its category. There are a bunch of factors which decide which
category a widget is. Currently there is no formal classification of these
categories and we calculate the category of the widget based on these
factors whenever we want to know it. This is at least once for every widget
during each power update sequence. The factors which determine the category
of the widgets are mostly static though and if at all change rather seldom.
This patch introduces three new per widget flags, one for each of non-normal
widgets categories. Instead of re-computing the category each time we want
to know them the flags will be checked. For the majority of widgets the
category is solely determined by the widget id, which means it never changes
and only has to be set once when the widget is created. The only widgets
with dynamic categories are:
snd_soc_dapm_dai_out: Is considered a sink iff the capture stream is
active, otherwise normal.
snd_soc_dapm_dai_in: Is considered a source iff the playback stream
is active, otherwise normal.
snd_soc_dapm_input: Is considered a sink iff it has no outgoing
paths, otherwise normal.
snd_soc_dapm_output: Is considered a source iff it has no incoming
paths, otherwise normal.
snd_soc_dapm_line: Is considered a sink iff it has no outgoing paths
and is considered a source iff it has no incoming paths,
otherwise normal.
For snd_soc_dapm_dai_out/snd_soc_dapm_dai_in widgets the category will be
updated when a stream is started or stopped. For the other dynamic widgets
the category will be updated when a path connecting to it is added or
removed.
Introducing those new widget categories allows to make
is_connected_{output,input}_ep, which are among the hottest paths of the
DAPM algorithm, more generic and significantly shorter.
The before and after sizes for is_connected_{output,input}_ep are:
On ARM (defconfig + CONFIG_SND_SOC):
function old new delta
is_connected_output_ep 480 340 -140
is_connected_input_ep 456 352 -104
On amd64 (defconfig + CONFIG_SND_SOC):
function old new delta
is_connected_output_ep 579 427 -152
is_connected_input_ep 563 427 -136
Which is about a 25%-30% decrease, other architectures are expected to have
similar numbers. At the same time the size of the snd_soc_dapm_widget struct
does not change since the new flags are stored in the same word as the
existing flags.
Note: that since the per widget 'ext' flag was only used to decide whether a
snd_soc_dapm_input or snd_soc_dapm_output widget was a source or a sink it
is now unused and can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Controls on a path only have an effect if the sink on the path is either a
mixer or mux widget. Currently we sort of silently ignore controls on other
paths, but since they don't do anything having them on other paths does not
make much sense and it is probably safe to assume that if we see such a path
it is a mistake in the driver that registered the path. This patch modifies
snd_soc_dapm_add_path() to report an error if a path with and control is
encountered where we didn't expect a control. This also allows to simplify
the code quite a bit.
The patch also moves the connecting of the path lists out of
dapm_connect_mux() and dapm_connect_mixer() into snd_soc_dapm_add_path().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Paths that are directly connected to a MUX widget are not affected by
changes to the MUX's control. Rather than checking if a path is directly
connected each time the MUX is updated do it only once when MUX is created.
We can also remove the check for e->texts[mux] != NULL, since if that
condition was true the code would have had already crashed much earlier (And
generally speaking if a enum's 'texts' entry is NULL it's a bug in the
driver).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rework soc_dapm_{mixer,mux}_update_power() to only mark a path dirty if the
connect state if the path has actually changed. This avoids unnecessary
power state checks for the widgets involved.
Also factor out the common code that is involved in this into a helper
function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Kernel dump (WARN_ON) ocurred during system boot-up inside regmap_write():
------------[ cut here ]------------
WARNING: CPU: 0 PID: 47 at kernel/locking/lockdep.c:2744 lockdep_trace_alloc+0xe8/0x108()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
Modules linked in:
CPU: 0 PID: 47 Comm: kworker/u2:2 Not tainted 3.18.0-rc1-10245-gb75d289-dirty #56
Workqueue: deferwq deferred_probe_work_func
Backtrace:
[<80012294>] (dump_backtrace) from [<80012578>] (show_stack+0x18/0x1c)
r6:8097c73c r5:8097c73c r4:00000000 r3:be33ba80
[<80012560>] (show_stack) from [<806aac48>] (dump_stack+0x8c/0xa4)
[<806aabbc>] (dump_stack) from [<8002a694>] (warn_slowpath_common+0x70/0x94)
r6:80062838 r5:00000009 r4:bd827b30 r3:be33ba80
[<8002a624>] (warn_slowpath_common) from [<8002a6f0>] (warn_slowpath_fmt+0x38/0x40)
r8:00000004 r7:00000001 r6:000080d0 r5:60000193 r4:bd826010
[<8002a6bc>] (warn_slowpath_fmt) from [<80062838>] (lockdep_trace_alloc+0xe8/0x108)
r3:80831590 r2:8082e160
[<80062750>] (lockdep_trace_alloc) from [<800ea5dc>] (kmem_cache_alloc+0x28/0x134)
r5:000080d0 r4:be001f00
[<800ea5b4>] (kmem_cache_alloc) from [<8038d72c>] (regcache_rbtree_write+0x15c/0x648)
r10:00000000 r9:0000001c r8:00000004 r7:00000001 r6:00000000 r5:bd819a00
r4:00000000 r3:811aea88
[<8038d5d0>] (regcache_rbtree_write) from [<8038c4d8>] (regcache_write+0x5c/0x64)
r10:be3f9f88 r9:00000000 r8:00000004 r7:00000001 r6:00000000 r5:00000001
r4:bd819a00
[<8038c47c>] (regcache_write) from [<8038b0dc>] (_regmap_raw_write+0x134/0x5f4)
r6:be3f9f84 r5:00000001 r4:bd819a00 r3:00000001
[<8038afa8>] (_regmap_raw_write) from [<8038b610>] (_regmap_bus_raw_write+0x74/0x94)
r10:00000000 r9:00000001 r8:be3fb080 r7:bd819a00 r6:00000001 r5:00000000
r4:bd819a00
[<8038b59c>] (_regmap_bus_raw_write) from [<8038a8b4>] (_regmap_write+0x60/0x9c)
r6:00000001 r5:00000000 r4:bd819a00 r3:8038b59c
[<8038a854>] (_regmap_write) from [<8038ba24>] (regmap_write+0x48/0x68)
r7:bd81ad80 r6:00000001 r5:00000000 r4:bd819a00
[<8038b9dc>] (regmap_write) from [<80528f30>] (fsl_asrc_dai_probe+0x34/0x104)
r6:bd888628 r5:be3fb080 r4:be3b4410 r3:be3b442c
------------[ dump end ]------------
=============================================================================
2741 /*
2742 * Oi! Can't be having __GFP_FS allocations with IRQs disabled.
2743 */
2744 if (DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags)))
2745 return;
=============================================================================
By looking at 2744 line, we can get that it's because regcache_rbtree_write()
would call kmalloc() with GFP flag if it couldn't find an existing block to
insert nodes while this kmalloc() call is inside a spin_lock_irq_save pair,
i.e. IRQs disabled.
Even though this may be a bug that should be fixed, I still try to send this
patch as a quick fix (work around) since it does no harm to assign default
values of every registers when using regcache.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In order to support both ACPI and PCI devices we need to use a genric device
id in driver, so change all pci_id instances to device_id
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'asoc/fix/intel', 'asoc/fix/s6000' and 'asoc/fix/sgtl5000' into asoc-linus
|
|
Create a separate module for rt5677 spi driver. Without
this patch, the build fails due to multiple defs of
'init_module' and 'cleanup_module'. module_spi_driver()
defines its own module, so it can't be part of the rt5677
module.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the new flags argument to calls of (devm_)gpiod_get*() and
remove any direction setting code afterwards.
Currently both forms (with or without the flags argument)
are valid thanks to transitional macros in
<linux/gpio/consumer.h>. These macros will be removed once
all consumers are updated and the flags argument will become
compulsary.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
DVC can control Digital Volume / Mute / Volume Ramp etc,
and these uses different max value.
Current driver is using fixed max value for each settings.
This patch adds new struct rsnd_dvc_cfg, and control these.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
