| Age | Commit message (Collapse) | Author |
|---|
|
The references used for the noise gates and parameters for their triggering
are configurable, expose that to users.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Though the controls are named as stereo controls in the part the main use
case for the analogue inputs to the WM5102 is mono. Reflect this in the
controls exposed to userspace, providing a series of mono controls rather
than stereo ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Though the controls are named as stereo controls in the part the main use
case for the analogue inputs to the WM5102 is mono. Reflect this in the
controls exposed to userspace, providing a series of mono controls rather
than stereo ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
If the FLL is being shut down we will exit early so there is no need to
check here and in fact we're checking the wrong thing anyway.
Reported-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Add device tree support.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
idle_bias_off
Just found some cases that some codec drivers set the bias to _STANDBY and
set idle_bias_off to 1 during probing.
It will cause unpaired runtime_get_sync/put() issue. Also as Mark suggested,
there is no reason to start from _STANDBY bias with idle_bias_off == 1.
So here giving one warning when detected (dapm.idle_bias_off == 1) and
(dapm.bias_level != SND_SOC_BIAS_OFF) just after driver->probe().
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The mode variable is either 0 or 1.
To update mode setting, the mask should be BIT(0) rather than BIT(1).
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Omair M. Abdullah <omair.m.abdullah@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
sgtl5000 microphone gain only has 2 bits of resolution, so maximum value is 3.
From Eric Nelson:
"We also found that for the microphones we have here (commodity PC boom mics) a
default value of 2 for the gain gives the best results."
So change the default microphone gain as well.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
commit 9bde4f0b1c (ASoC: core: Fix SOC_DOUBLE_RANGE() macros) introduced
the following build warning:
sound/soc/soc-core.c:2999:6: warning: unused variable 'ret' [-Wunused-variable]
Remove the unused 'ret' variable.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
According to the defines in wm2200.h:
/*
* R1284 (0x504) - Audio IF 1_5
*/
We should not left shift 1 bit for fmt_val when setting dai format.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
Although we've had macros defining double _RANGE controls for a while now
they've not actually been backed up properly by the implementation, it's
treated everything as mono. Fix that by implementing the handling in the
stereo controls, ensuring that the mono controls don't mistakenly get
treated as stereo.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
|
|
Both the mask and mode settings are wrong in current code.
According to the datasheet:
S2PCFG0 (0x0A)
BIT[3:1] DATA_FORMAT
serial interface protocol format:
000: left Justified
001: I2S (default)
010: right justified
100: PCM no delay
101: PCM delay
111: DSP
Thus fixes the defines for LEFT_J_DATA_FORMAT, I2S_DATA_FORMAT, and
RIGHT_J_DATA_FORMAT.
Also adds define for DATA_FORMAT_MSK.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
When front-end PCM session is in paused state, back-end
PCM session will be put in paused state as well if given
front-end PCM session is the only client of given back-end.
Then, application closes front-end PCM session, DPCM
framework will not allow back-end enters HW_FREE state
so back-end will never get shutdown completely.
Signed-off-by: Patrick Lai <plai@codeaurora.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This update contains overall only driver-specific fixes. Slightly
large LOC are seen in usb-audio driver for a couple of new device
quirks and cs42l71 ASoC driver for enhanced features. The others are
a few small (regression) fixes HD-audio, and yet other small / trival
ASoC fixes."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: usb-audio: Support for Digidesign Mbox 2 USB sound card:
ALSA: HDA: Fix sound resume hang
ALSA: hda - bug fix for invalid connection list of Haswell HDMI codec pins
ALSA: hda - Fix the wrong pincaps set in ALC861VD dallas/hp fixup
ALSA: hda - Set codec->single_adc_amp flag for Realtek codecs
ASoC: atmel-ssc: change disable to disable in dts node
ASoC: Prevent pop_wait overwrite
ALSA: usb-audio: ignore-quirk for HP Wireless Audio
ALSA: hda - Always turn on pins for HDMI/DP
ALSA: hda - Fix pin configuration of HP Pavilion dv7
ASoC: core: Fix splitting of log messages
ASoC: cs42l73: Change VSPIN/VSPOUT to VSPINOUT
ASoC: cs42l73: Add DAPM events for power down.
ASoC: cs42l73: Add DMIC's as DAPM inputs.
ASoC: sigmadsp: Fix endianness conversion issue
ASoC: tpa6130a2: Use devm_* APIs
|
|
|
|
|
|
|
|
|
|
|
|
pop_wait is used to determine if a deferred playback close
needs to be cancelled when the a PCM is open or if after
the power-down delay expires it needs to run. pop_wait is
associated with the CODEC DAI, so the CODEC DAI must be
unique. This holds true for most CODECs, except for the
dummy CODEC and its DAI.
In DAI links with non-unique dummy CODECs (e.g. front-ends),
pop_wait can be overwritten by another DAI link using also a
dummy CODEC. Failure to cancel a deferred close can cause
mute due to the DAPM STOP event sent in the deferred work.
One scenario where pop_wait is overwritten and causing mute
is below (where hw:0,0 and hw:0,1 are two front-ends with
default pmdown_time = 5 secs):
aplay /dev/urandom -D hw:0,0 -c 2 -r 48000 -f S16_LE -d 1
sleep 1
aplay /dev/urandom -D hw:0,1 -c 2 -r 48000 -f S16_LE -d 3 &
aplay /dev/urandom -D hw:0,0 -c 2 -r 48000 -f S16_LE
Since CODECs may not be unique, pop_wait is moved to the PCM
runtime structure. Creating separate dummy CODECs for each
DAI link can also solve the problem, but at this point it's
only pop_wait variable in the CODEC DAI that has negative
effects by not being unique.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This update contains a fairly wide range of changes all over in sound
subdirectory, mainly because of UAPI header moves by David and __dev*
annotation removals by Bill. Other highlights are:
- Introduced the support for wallclock timestamps in ALSA PCM core
- Add the poll loop implementation for HD-audio jack detection
- Yet more VGA-switcheroo fixes for HD-audio
- New VIA HD-audio codec support
- More fixes on resource management in USB audio and MIDI drivers
- More quirks for USB-audio ASUS Xonar U3, Reloop Play, Focusrite,
Roland VG-99, etc
- Add support for FastTrack C400 usb-audio
- Clean ups in many drivers regarding firmware loading
- Add PSC724 Ultiimate Edge support to ice1712
- A few hdspm driver updates
- New Stanton SCS.1d/1m FireWire driver
- Standardisation of the logging in ASoC codes
- DT and dmaengine support for ASoC Atmel
- Support for Wolfson ADSP cores
- New drivers for Freescale/iVeia P1022 and Maxim MAX98090
- Lots of other ASoC driver fixes and developments"
Fix up trivial conflicts. And go out on a limb and assume the dts file
'status' field of one of the conflicting things was supposed to be
"disabled", not "disable" like in pretty much all other cases.
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (341 commits)
ALSA: hda - Move runtime PM check to runtime_idle callback
ALSA: hda - Add stereo-dmic fixup for Acer Aspire One 522
ALSA: hda - Avoid doubly suspend after vga switcheroo
ALSA: usb-audio: Enable S/PDIF on the ASUS Xonar U3
ALSA: hda - Check validity of CORB/RIRB WP reads
ALSA: hda - use usleep_range in link reset and change timeout check
ALSA: HDA: VIA: Add support for codec VT1808.
ALSA: HDA: VIA Add support for codec VT1705CF.
ASoC: codecs: remove __dev* attributes
ASoC: utils: remove __dev* attributes
ASoC: ux500: remove __dev* attributes
ASoC: txx9: remove __dev* attributes
ASoC: tegra: remove __dev* attributes
ASoC: spear: remove __dev* attributes
ASoC: sh: remove __dev* attributes
ASoC: s6000: remove __dev* attributes
ASoC: OMAP: remove __dev* attributes
ASoC: nuc900: remove __dev* attributes
ASoC: mxs: remove __dev* attributes
ASoC: kirkwood: remove __dev* attributes
...
|
|
Pull ARM SoC board updates, take 2 from Olof Johansson:
"This branch contains board updates for shmobile that had dependencies
on earlier branches past the first driver branch, and thus are merged
separately.
Most of these are to enable audio and USB on shmobile. They contain a
dependent ASoC branch that has been coordinated with Mark Brown."
* tag 'boards2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: shmobile: mackerel: Add FLCTL IRQ resource
ARM: shmobile: use FSI driver's audio clock on ap4evb
ARM: shmobile: use FSI driver's audio clock on mackerel
ARM: shmobile: use FSI driver's audio clock on armadillo800eva
ARM: shmobile: mackerel: enable DMAEngine on USB Host
ARM: shmobile: marzen: add USB OHCI driver support
ARM: shmobile: marzen: add USB EHCI driver support
ARM: shmobile: marzen: add USB phy support
ASoC: fsi: add master clock control functions
ASoC: fsi: care fsi_hw_start/stop() return value
ASoC: fsi: fsi_set_master_clk() was called from fsi_hw_xxx() only
ASoC: fsi: use devm_request_irq()
ASoC: fsi: fixup channels_min/max
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC power management and clock changes from Olof Johansson:
"This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable."
* tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: voltage: fixup oscillator handling when CONFIG_PM=n
ARM: OMAP4: USB: power down MUSB PHY during boot
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform conversion patches from Olof Johansson:
"Here are more patches in the progression towards multiplatform, sparse
irq conversions in particular.
Tegra has a handful of cleanups and general groundwork, but is not
quite there yet on full enablement.
Platforms that are enabled through this branch are VT8500 and Zynq.
Note that i.MX was converted in one of the earlier cleanup branches as
well (before we started a separate topic for multiplatform). And both
new platforms for this merge window, sunxi and bcm, were merged with
multiplatform support enabled."
Fix up conflicts mostly as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (29 commits)
ARM: zynq: Remove all unused mach headers
ARM: zynq: add support for ARCH_MULTIPLATFORM
ARM: zynq: make use of debug_ll_io_init()
ARM: zynq: remove TTC early mapping
ARM: tegra: move debug-macro.S to include/debug
ARM: tegra: don't include iomap.h from debug-macro.S
ARM: tegra: decouple uncompress.h and debug-macro.S
ARM: tegra: simplify DEBUG_LL UART selection options
ARM: tegra: select SPARSE_IRQ
ARM: tegra: enhance timer.c to get IO address from device tree
ARM: tegra: enhance timer.c to get IRQ info from device tree
ARM: timer: fix checkpatch warnings
ARM: tegra: add TWD to device tree
ARM: tegra: define DT bindings for and instantiate RTC
ARM: tegra: define DT bindings for and instantiate timer
clocksource/mtu-nomadik: use apb_pclk
clk: ux500: Register mtu apb_pclocks
ARM: plat-nomadik: convert platforms to SPARSE_IRQ
mfd/db8500-prcmu: use the irq_domain_add_simple()
mfd/ab8500-core: use irq_domain_add_simple()
...
|
|
Don't wrap log messages over multiple lines, it makes them hard to grep
for.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Since VSP only has one power bit, only provide one DAPM widget.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Add power down delays between setting PDN and MCLKDIS for spk amp, spklo amp, and ear amp.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The 'addr' field of the sigma_action struct is stored as big endian in the
firmware file.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
