| Age | Commit message (Collapse) | Author |
|---|
|
It seems this driver hasn't been updated for SMP, as local_irq_save/
local_irq_restore don't provide proper protection of read/modify/write
of the device's registers on such systems. Introduce a spinlock
serializing access to the register region, it will be helpful later
when I2SMOD, I2SPSR registers are made also accessible through the
clk API.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The usage of this goto seems unjustified, use if/else statement instead.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The code to get pointer to the other DAI is repeated multiple
times. Add a helper function and use it instead.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The clk_prepare_enable() call on the "iis" clock is moved to happen earlier
in the DAI platform device driver's probe() callback, so the I2S registers
can be safely accessed through the clk API, after the clk supplier is
registered in the platform device probe().
After this patch the "iis" clock is kept enabled since the (primary) I2S
platform device probe() and until the platform device driver remove() call.
This is similar to gating the clock in the snd_soc_dai probe() and remove()
callbacks.
Normally, in addition to that we should mark the device as PM runtime active,
so if runtime PM is enabled it can idle the device by turning off the clock.
Correcting this issue is left for a separate patch series, as we need to
ensure the BUSCLK clock is always enabled when required.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Acquire the I2S interface clock in driver probe() callback
as it's a per-device not a per-DAI clock. While at it switch
to the resource managed clk_get().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The memory mapped registers region is common for both DAIs so request
it in the I2S platform device driver's probe for the platform device
corresponding to the primary DAI, rather than in the ASoC DAI's probe
callback. While at it switch to devm_ioremap_resource(). This also
drops the hard coded (0x100) register region size in the driver.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
These functions may fail so let's properly report any errors.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Tidy up the samsung_i2s_get_driver_data() function by using
IS_ENABLE() instead of #ifdef and add missing braces for
the 'else' part. Also ensure we are not dereferencing NULL
'match' pointer.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When we want to use wm8960 codec, we should enable its MCLK in machine driver.
It's reasonable for wm8960 codec driver to manage its own MCLK.
When current bias_level is SND_SOC_BIAS_ON, it is preparing for a transition
away from ON. In this case, disable the codec mclk. When current bias_level
is not SND_SOC_BIAS_ON, it preparing for a transition to ON. In this case,
enable the codec mclk.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There have been some conflicting interpretations of how
snd_soc_dai_set_tdm_slot() is supposed to work. This patch updates the
documentation to be more specific on the exact semantics to avoid such
problems in the future.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now that the fsl DAI drivers uses the same semantics as the rest of a ASoC
the custom fsl_asoc_xlate_tdm_slot_mask() callback can be removed as it is
identical to the generic one.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The fsl-ssi and imx-ssi drivers use inverted semantics for the tx_mask and
rx_mask parameter of the set_tdm_slot() callback compared to rest of ASoC.
This patch updates the driver's semantics to be consistent with the rest of
ASoC, i.e. a set bit means a active slot and a cleared bit means a inactive
slot. This will allow us to use the set_tdm_slot() API in a more generic
way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The mc13783 driver uses inverted semantics for the tx_mask and rx_mask
parameter of the set_tdm_slot() callback compared to rest of ASoC. This
patch updates the driver's semantics to be consistent with the rest of ASoC,
i.e. a set bit means a active slot and a cleared bit means a inactive slot.
This will allow us to use the set_tdm_slot() API in a more generic way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Correct the path name for mux to get rid of the following warning:
--->8---
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTR
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTR
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACL
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACL
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACR
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACR
---8<---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The SOC_AT91SAM9X5 option is going to be removed, only depend on ARCH_AT91 like
for the other drivers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set the card owner field to avoid getting a kernel crash when the imx-spdif
is unloaded while the playback is active.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add the slot_width "25" support in the TDM mode for the Intel platform.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The patch uses the regmap functions instead of the snd_soc functions in some
cases.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If asoc_simple_card_probe() fails, asoc_simple_card_unref() may be
called before dev_set_drvdata(), causing a NULL pointer dereference in
asoc_simple_card_unref():
Unable to handle kernel NULL pointer dereference at virtual address 000000d4
...
PC is at asoc_simple_card_unref+0x14/0x48
LR is at asoc_simple_card_probe+0x3d4/0x40c
This typically happens because asoc_simple_card_parse_of() returns
-EPROBE_DEFER, but other failure modes are possible.
devm_snd_soc_register_card()/snd_soc_register_card() may fail either
before or after dev_set_drvdata().
Pass a snd_soc_card pointer instead of a platform_device pointer to
asoc_simple_card_unref() to fix this.
Note that if CONFIG_OF_DYNAMIC=n, of_node_put() is a dummy, and gcc may
optimize away the loop over card->dai_link, never actually dereferencing
card, and thus avoiding the crash...
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: e512e001dafa54e5 ("ASoC: simple-card: Fix the reference count of device nodes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
Since commit 2ffa531078037a0 ("ASoC: fsl_ssi: Fix module unbound") the irq
number is retrieved via platform_get_irq(), which may fail and return a negative
number, so adapt its type to 'int'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The following crash happens when trying to unload the snd_soc_imx_wm8962 module
while playback is active:
[ 208.666868] Unable to handle kernel paging request at virtc
[ 208.674110] pgd = 80004000
[ 208.676867] [7f06541c] *pgd=4c334811, *pte=00000000, *ppte=00000000
[ 208.683211] Internal error: Oops: 80000007 [#1] SMP ARM
[ 208.688445] Modules linked in: snd_soc_wm8962 snd_soc_fsl_ssi snd_soc_imx_audmux imx_pcm_fiq evbug]
...
In order to avoid such problem, fill the card owner field as suggested by
Lars-Peter Clausen:
"But looking at the source it seems that this is a core feature of ALSA and at
least for the card module itself it will do the ref-counting when a stream is
started/stopped. And we even support setting the owner of a card in ASoC.
It's just that pretty much no ASoC card driver bothers to set the owner field
in the snd_soc_card struct. So this particular problem can be fixed by updating
the imx-wm8962 driver to set the owner field."
By doing as suggested, we no longer see the crash when attempting to unload the
snd_soc_imx_wm8962 module while playback is active:
$ modprobe -r snd_soc_imx_wm8962
modprobe: can't unload module snd_soc_imx_wm8962: Resource temporarily
unavailable
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
L/R channel will be switched if under/over flow error happen on
Renesas R-Car sound device by the HW bugs. Then, HW restart is required
for salvage. This patch add salvage support for SRC.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The DAC powerdown bit is managed by DAPM. Manually powering down the DAC in
the CODEC probe function may cause unnecessary power state transitions which
can lead to click and pop noises.
So leave the DAC powerdown bit in its default poweron-reset state and let
DAPM do all the management.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
All DAPM input and output pins of the wm8750 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
All DAPM input and output pins of the wm9712 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The microphone route has sink and source swapped.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
All DAPM input and output pins of the uda1380 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
All DAPM input and output pins of the ak4641 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
All DAPM input and output pins of the wm9705 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
All DAPM input and output pins of the wm9705 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
All DAPM input and output pins of the wm8994 are either used in the card's
DAPM routing table or are marked as not connected.
Set the fully_routed flag of the card instead of manually marking the unused
inputs and outputs as not connected. This makes the code a bit shorter and
cleaner.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The "Headset Mic 2" and the "Headset Stereophone" widget are managed by the
jack detection logic. Their will be set depending on whether something is
connected to the jack or not. There is no need to manually change the state
beforehand as it will be overwritten anyway.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The DSP programs are listed out of order.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
|
|
The patch modified the behavior that updates the PLL parameter. It set the
update bit before the PLL power up.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
There may be 2 pcm streams for a same DAI at most, and these 2
streams should have different hsw_pcm_data, e.g. they have
different persistent data, so here we need split hsw_pcm_data
for playback and capture, to make sure they won't be mixed
and keep cleaned.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Reviewed-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Conflicts:
sound/soc/fsl/fsl_ssi.c
|
|
XTFPGA boards provides an audio subsystem that consists of TI CDCE706
clock synthesizer, I2S transmitter and TLV320AIC23 audio codec.
I2S transmitter has MMIO-based interface that resembles that of the
OpenCores I2S transmitter. I2S transmitter is always a master on I2S
bus. There's no specialized audio DMA, sample data are transferred to
I2S transmitter FIFO by CPU through memory-mapped queue interface.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The patch adds the MICBIAS VDD setting in the platform data. It can be set to
1V8 or 3V3 in the MICBIAS VDD.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently the error message uses 'np->full_name' which leads to a very verbose
log as:
fsl-ssi-dai 202c000.ssi: no irq for node /soc/aips-bus@02000000/spba-bus@02000000/ssi@0202c000
We can have a concise log by using pdev->name instead:
fsl-ssi-dai 202c000.ssi: no irq for node 202c000.ssi
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
A DAI may have 2 streams(playback/capture) and different modules
may be needed for them respectively, so we need add a stream
direction here, the combination(dai_id + stream) can tell us
which module we really need here.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The first 512 bytes of data DRAM memory is used for FW dump,
and this first data SRAM block should be never power gated
(always on), here always enable the block(DSRAM[0]) for D0
stage.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 2ffa531078037a0 ("ASoC: fsl_ssi: Fix module unbound") changed the way to
retrieve the irq number from irq_of_parse_and_map() to platform_get_irq(), but
missed to updated the irq error check accordingly.
We should test for negative irq number and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch introduces the use of function put_unaligned_be16.
This is done using Coccinelle and semantic patch used is as follows:
@a@
typedef u16, __be16, uint16_t;
{u16,__be16,uint16_t} e16;
identifier tmp;
expression ptr;
expression y,e;
type T;
@@
- tmp = cpu_to_be16(y);
<+... when != tmp
(
- memcpy(ptr, (T)&tmp, \(2\|sizeof(u16)\|sizeof(__be16)\|sizeof(uint16_t)\|sizeof(e16)\));
+ put_unaligned_be16(y,ptr);
|
- memcpy(ptr, (T)&tmp, ...);
+ put_unaligned_be16(y,ptr);
)
...+>
? tmp = e
@@ type T; identifier a.tmp; @@
- T tmp;
...when != tmp
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
--
Changes Since v2:
Make the patch compatible for current code
sound/soc/codecs/wm5102.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Export snd_soc_runtime_set_dai_fmt() so it can be used in modules.
Fixes: ce64c8b9cf5b ("ASoC: Add helper function for changing the DAI link format")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch applys rate symmetry for rockchip i2s DAI.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver supports NVIDIA Tegra Ryu board
Sponsored: Google ChromeOS
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
