| Age | Commit message (Collapse) | Author |
|---|
|
Added support for the Edirol UA-101 (only in high-speed mode) by taking
the quirks for the UA-1000 and change them accordingly. Changes were
made in 'usbaudio.c', 'usbaudio.h', and 'usbquirks.h'
MIDI and recording seem to work perfectly (with JACK), but playback
gives some few glitches. I think that's the mentioned
synchronizing-problem in the UA-1000 quirk ('FIXME: playback must be
synchronized to capture'), so I didn't change that.
ToDo: Adding Mixer-Support for the built-in
control-panel/patch-bay/router.
Signed-off-by: Bjoern Fay <mail@bfay.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
The patch fixes the memory corruption by the support of unconventional
sample rates. Also, it avoids the too restrictive constraints if
any of usb descriptions contain continuous rates.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
This is a patch for ALSA Bug #2724. Some webcams provide bogus
settings with no valid rates. With this patch those are skipped.
Signed-off-by: Gregor Jasny <gjasny@web.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Went rummaging through usbaudio.c and found some castings that
aren't needed as far as I can see. Part of the KernelJanitors
TODO list.
Signed-off-by: John Daiker <daikerjohn@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Add pause capabilities for both USB playback and capture streams.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
The hardware information structures for playback and capture streams,
respectively, are the same, so we can use just one structure for both
streams.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
The previous patch 'Repair snd-usb-usx2y for usb 2.6.18' assumed
urb->start_frame roll over beyond MAX_INT for both UHCI & OHCI.
This isn't true until now (kernel 2.6.20).
Fix this by only looking at the common between OHCI & UHCI Frame number
range.
This is for mainline and stable kernels >= 2.6.18.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fixed the error from kobject_add() at reconnection the usb audio device.
This happens when an app keeps opening a device while the device is
replugged, due to the confliction of the internal bookkept index and
the really empty slot.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Without the patch below namelist[0] will not be freed in case
of kmalloc error.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
The C-Media CM6501 chip's descriptors say that altsetting 5 supports
48 kHz, but it actually plays at 96 kHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Handle the return value of usb_register() in the module_init function.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Some drivers are returning OOM when it is not in response to a memory
shortage.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
- usb_free_urb() cleanup
- usb_kill_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
- usb_kill_urb() cleanup
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix hang-up at disconnection of usb-audio devices while accessing PCM.
Don't handle PCM operations any more after shutdown flag is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
urb->start_frame rolls over beyond MAX_INT now.
This is for stable kernel and stable alsa.
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fix bug in snd-usb-usx2y's usX2Y_pcms_lock_check()
substream can be NULL......
in mainline, bug was introduced by:
2006-06-22 [ALSA] Add O_APPEND flag support to PCM
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
|
|
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
The purpose of this patch is to split off the case when a device does
not reply on the lower level (which is reported by HC hardware), and
a case when the device accepted the request, but does not reply at
upper level. This redefinition allows to diagnose issues easier,
without asking the user if the -110 happened "immediately".
The usbmon splits such cases already thanks to its timestamp, but
it's not always available.
I adjusted all drivers which I found affected (by searching for "urb").
Out of tree drivers may suffer a little bit, but I do not expect much
breakage. At worst they may print a few messages.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add a mixer name map for the TerraTec Aureon 5.1 MkII USB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
To decrease the USB interrupts rate, increase both the default and the
maximum number of packets per URB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
There's at least one USB audio chipset out there which supports only one
non-standard rate (ID 0e6a:0310 supports 46875Hz). There's a few other
patches for this card which are unsatisfactory because they attempt to
map this rate to 44.1k leading to sound distortion.
The patch below uses SNDRV_PCM_RATE_KNOT to properly support the
non-standard rates where they are available.
Signed-off-by: Luke Ross <luke@lukeross.name>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Fixed a typo of CONFIG_PROC_FS in usbaudio.c.
The stream proc file appears again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Add some quirks for some unknown Yamaha USB MIDI devices.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Added TLV-read support to snd-usb-audio driver for passing
the volume dB scale information to user-space.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Orignally proposed by Sam Revitch <sam.revitch@gmail.com>.
Unregister device files at disconnection to avoid the futher accesses.
Also, the dev_unregister callback is removed and replaced with the
combination of disconnect + free.
A new function snd_card_free_when_closed() is introduced, which is
used in USB disconnect callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
sound: Conversions from kmalloc+memset to k(c|z)alloc.
Signed-off-by: Panagiotis Issaris <takis@issaris.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
From: Sam Revitch <sam.revitch@gmail.com>Recently a Turtle Beach Audio Advantage Roadie device ended up in my
possession. It seems to work with the snd-usb-audio driver, but only
using the headphone jack in 2-channel mode. The device has a DIN
connector carrying six more channels that are otherwise silent.
C-Media has freely available documentation for the CM106 chip around
which this device is based, and enabling 8-channel output, or
6-channel output with the headphone jack following the front pair is a
matter of setting one of its registers.
Attached is a patch to try to enable 5.1 output mode at probe time.
It seems to work correctly with my device. There is quite list of
other configurables for this device that might deserve controls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
|
|
Removed the CS_AUDIO_* #defines, which were duplicates of the
class-specific USB_DT_CS_* #defines in <linux/usb_ch9.h>.
Signed-off-by: Ben Williamson <ben.williamson@greyinnovation.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix a typo introduced by the last fix.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some devices don't have the required class-specific endpoint descriptors.
Instead of making this case an error, this patch makes the driver guess the
endpoint attributes.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
This patch rewrites the remote control code to use a table for
the peculiarities of the various SB models, and adds support
for a third model.
Signed-off-by: Raimonds Cicans <ray@vardes.lv>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Add a get_port_info callback to the snd_rawmidi_global_ops structure to
allow the USB MIDI driver to supply information flags for the sequencer
ports created by seq_midi.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Added O_APPEND flag support to PCM to enable shared substreams
among multiple processes. This mechanism is used by dmix and
dsnoop plugins.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove unneeded read/write_size fields in proc text ops.
snd_info_set_text_ops() is fixed, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a quirk entry for the TerraTec Phase 26 with yet another product ID.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Test the volume of usb audio whether actually it works and adjusts
the resolution value according to it.
Some USB audio devices report a lower resolution than it reacts.
The only possible check is to write and read a volume value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix a lot of typos. Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Modules: USB generic driver
We may leak 'namelist' in sound/usb/usbmixer.c::parse_audio_selector_unit()
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: USB generic driver
Add mixer control names for the AudioTrak Maya44 USB.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: USB generic driver
Add a quirk entry for the Casio PL-40R.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: USB generic driver
Add support for the Yamaha MDP-5 and EZ-J24.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: Documentation,USB generic driver
The patch adds the 'device_setup' module parameter and a specific
quirk to correctly initialize the audiophile usb device: this fixes
the distorted sound bug on the Analog capture port. Backward
compatibility is achieved by simply omitting the new parameter.
Signed-off-by: Thibault LE MEUR <Thibault.LeMeur@supelec.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: USB generic driver
Add an error message for -ENOSYS for situations when split iso support
is needed but not enabled.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: USB generic driver
Use a generic name for USB device 0x07cf:0x6802 because this ID is used
by several devices without a product ID.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: USB generic driver
When usb_submit_urb() fails, show an error description instead of just
the error code.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: USB generic driver
Add a quirk for the Casio AP-80R.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
|
Modules: USB generic driver
snd_ctl_add() kfree's the kcontrol already if we fail there,
so this driver is currently doing a double kfree.
Coverity bug #959
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Modules: USB generic driver
Reduce the code size of the snd_usbmidi_count_bits() function by using
simpler operations.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
|
