| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
|
|
ALC889 has two SPDIF outputs: 0x06, 0x10. Board vendors can use either or both.
DX58SO uses 0x10, but the driver assumes 0x06. The safe solution is to add
0x10 as slave output to the existing 0x06.
Reported-by: Jeroen Van Breedam <jeroen.vanbreedam@sgr5.be>
Tested-by: Jeroen Van Breedam <jeroen.vanbreedam@sgr5.be>
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch increases periods_min to 6 from 4, this will remove any
hickups where the buffer is not filled fast enough from user space.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch replaces the references to bus_id to the new dev_name() API.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch replaces the references to bus_id to the new dev_name() API.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch will set the channel A and control channel mode register to
zero before disabling the AC97C peripheral.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch will enable the AC97C before resetting the external codec,
leaving the AC97C disabled will result in floating I/O lines that can
affect the reset procedure.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch will enable interrupts from AC97C and report about error
conditions that occurs.
On channel A both overrun and underrun will be enabled depending if
playback and/or capture are enabled. On the control channel the overrun
interrupt is enabled.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch will set a proper maximum bytes for the buffer, which is:
channels * bytes per sample * maximum periods * maximum bytes per period.
It also sets the minimum periods to 6, a value chosen from testing, with
a minimum of 6 periods the system has good time to fill in new audio
data without skipping.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch will take care not to overwrite OCA and ICA registers when
assigning input and output channels. It will also make sure the
registers are at a known state when enabling a channel and clean up
properly in case of an error.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch will remove traces of channel B registers, since they are not
used by the AC97C driver. Channel B might be used for other purposes.
The driver also adds channel status bits TXEMPTY and OVRUN and a
AC97C_CH_MASK macro to ease clearing a channel settings.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added device id in struct for codec 92HD81B1C (0x111d76d5).
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A pointer to snd_pmac_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (when having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Rene Herman <rene.herman@keyaccess.nl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
|
|
Add ZV port control switch.
This patch is done after solution
given in the ALSA bug #2872 report.
The patch resolves the issue.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
trivial: Update my email address
trivial: NULL noise: drivers/mtd/tests/mtd_*test.c
trivial: NULL noise: drivers/media/dvb/frontends/drx397xD_fw.h
trivial: Fix misspelling of "Celsius".
trivial: remove unused variable 'path' in alloc_file()
trivial: fix a pdlfush -> pdflush typo in comment
trivial: jbd header comment typo fix for JBD_PARANOID_IOFAIL
trivial: wusb: Storage class should be before const qualifier
trivial: drivers/char/bsr.c: Storage class should be before const qualifier
trivial: h8300: Storage class should be before const qualifier
trivial: fix where cgroup documentation is not correctly referred to
trivial: Give the right path in Documentation example
trivial: MTD: remove EOL from MODULE_DESCRIPTION
trivial: Fix typo in bio_split()'s documentation
trivial: PWM: fix of #endif comment
trivial: fix typos/grammar errors in Kconfig texts
trivial: Fix misspelling of firmware
trivial: cgroups: documentation typo and spelling corrections
trivial: Update contact info for Jochen Hein
trivial: fix typo "resgister" -> "register"
...
|
|
Adds the needed code to be able to use 96KHz playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Without this the WM9705 driver fails badly when resuming.
Tested-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Ensure that any AC97 devices that bind to the CODEC are below the
ASoC device in the device tree so the suspend and resume code can
figure out what order to handle them in.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
AC97 devices may have other drivers hanging off them directly so need to
have resumed when the resume function returns meaning that we can't defer
the resume - complete it immediately for them. Non-AC97 devices should
not have other drivers hanging directly off the ASoC devices.
We only really need the deferral for non-AC97 devices - it's there since
some I2C buses are very slow and non-AC97 codecs often have large numbers
of registers to restore and require delays to bring the codec up cleanly
leading to a substantial impact on overall resume time.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
McBSP2 in OMAP3 has 1 ksample (1k x 32 bit) internal FIFO. During
initial playback startup, this FIFO is keeping the DMA request active
until the FIFO is full.
So now if ALSA buffer size is smaller, DMA is looping around it while
filling up the HW FIFO, generating burst of interrupts as well and SW
doesn't have any change to fill enough data.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
In case of duplex mode (capture and playback at the same time), the second
stream has to have the same parameters (rate, sample size) as the already
running stream.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
TWL4030 supports 96KHz sample playback, but only playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Optimize the display of SSI statistics in the Freescale MPC8610 sound driver
to display the status count only of the interrupts that were actually enabled.
Previously, it would display the counts of all SISR status bits, even those
that were not enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
the variable gsr_bit is set in isr. It is however set to 0 and interrupts are
disabled prior to reset. Hence it doesn't make a lot of sense to show the
content of gsr_bit in case of a reset timeout.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Remove the delay from the trigger function in the Freescale MPC8610 sound
driver when capture is started. This delay was used to ensure that the DMA
controller was active when ALSA call the .pointer function to request a
DMA transfer status. A better approach is for the .pointer function to detect
that DMA has not started, and return zero instead. This change eliminates
the need for the delay.
Also add some related code to check for a DMA programming error, and report
XRUN if it occurs.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
HTC Magician has a Philips UDA1380 codec connected via
SSP1 (playback) and I2S (capture).
There is a flip-flop between the SSP frame clock output
and the codec's word select input pin. To make the codec
see proper I2S input, the SSP has to send two frames per
sample.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Now magician and similar boards can use network mode with only one
active slot to explicitly set 16 bit frame width, even for S16_LE
stereo sound.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Setting ->owner as done currently (pde->owner = THIS_MODULE) is racy
as correctly noted at bug #12454. Someone can lookup entry with NULL
->owner, thus not pinning enything, and release it later resulting
in module refcount underflow.
We can keep ->owner and supply it at registration time like ->proc_fops
and ->data.
But this leaves ->owner as easy-manipulative field (just one C assignment)
and somebody will forget to unpin previous/pin current module when
switching ->owner. ->proc_fops is declared as "const" which should give
some thoughts.
->read_proc/->write_proc were just fixed to not require ->owner for
protection.
rmmod'ed directories will be empty and return "." and ".." -- no harm.
And directories with tricky enough readdir and lookup shouldn't be modular.
We definitely don't want such modular code.
Removing ->owner will also make PDE smaller.
So, let's nuke it.
Kudos to Jeff Layton for reminding about this, let's say, oversight.
http://bugzilla.kernel.org/show_bug.cgi?id=12454
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
|
|
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Fix misspelling of firmware.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (422 commits)
[ARM] 5435/1: fix compile warning in sanity_check_meminfo()
[ARM] 5434/1: ARM: OMAP: Fix mailbox compile for 24xx
[ARM] pxa: fix the bad assumption that PCMCIA sockets always start with 0
[ARM] pxa: fix Colibri PXA300 and PXA320 LCD backlight pins
imxfb: Fix TFT mode
i.MX21/27: remove ifdef CONFIG_FB_IMX
imxfb: add clock support
mxc: add arch_reset() function
clkdev: add possibility to get a clock based on the device name
i.MX1: remove fb support from mach-imx
[ARM] pxa: build arch/arm/plat-pxa/mfp.c only when PXA3xx or ARCH_MMP defined
Gemini: Add support for Teltonika RUT100
Gemini: gpiolib based GPIO support v2
MAINTAINERS: add myself as Gemini architecture maintainer
ARM: Add Gemini architecture v3
[ARM] OMAP: Fix compile for omap2_init_common_hw()
MAINTAINERS: Add myself as Faraday ARM core variant maintainer
ARM: Add support for FA526 v2
[ARM] acorn,ebsa110,footbridge,integrator,sa1100: Convert asm/io.h to linux/io.h
[ARM] collie: fix two minor formatting nits
...
|
|
Conflicts:
sound/soc/pxa/pxa2xx-i2s.c
|
|
Conflicts:
arch/parisc/kernel/irq.c
arch/x86/include/asm/fixmap_64.h
arch/x86/include/asm/setup.h
kernel/irq/handle.c
Semantic merge:
arch/x86/include/asm/fixmap.h
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: irq_node.handler() should return irqreturn_t
m68k: section mismatch fixes: Atari SCSI
m68k: section mismatch fixes: DMAsound for Atari
MAINTAINERS: Replace dead link to m68k CVS repository by link to new git repository
m68k: mac - Add SWIM floppy support
m68k: mac - Add a new entry in mac_model to identify the floppy controller type.
m68k: Add install target
|
|
* 'bkl-removal' of git://git.lwn.net/linux-2.6:
Rationalize fasync return values
Move FASYNC bit handling to f_op->fasync()
Use f_lock to protect f_flags
Rename struct file->f_ep_lock
|
|
add __initdata to driver presets struct
Signed-off-By: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (96 commits)
sh: add support for SMSC Polaris platform
sh: fix the HD64461 level-triggered interrupts handling
sh: sh-rtc wakeup support
sh: sh-rtc invalid time rework
sh: sh-rtc carry interrupt rework
sh: disallow kexec virtual entry
sh: kexec jump: fix for ftrace.
sh: kexec: Drop SR.BL bit toggling.
sh: add kexec jump support
sh: rework kexec segment code
sh: simplify kexec vbr code
sh: Flush only the needed range when unmapping a VMA.
sh: Update debugfs ASID dumping for 16-bit ASID support.
sh: tlb-pteaex: Kill off legacy PTEA updates.
sh: Support for extended ASIDs on PTEAEX-capable SH-X3 cores.
sh: sh7763rdp: Change IRQ number for sh_eth of sh7763rdp
sh: espt-giga board support
sh: dma: Make G2 DMA configurable.
sh: dma: Make PVR2 DMA configurable.
sh: Move IRQ multi definition of DMAC to defconfig
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into devel
|
|
|
|
|
|
|
|
|
|
|
|
|
