| Age | Commit message (Collapse) | Author |
|---|
|
The PXA3xx does not support the use of interrupts during reset and access
to the GPIO status requires similar handling to that for PXA27x.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added the support of Terrasonq TS88.
Signed-off-by: Peter Lienig <lienig@rheinmetall-de.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
free_irq() calls synchronize_irq() for you, so there is no need for
drivers to manually do the same thing (again). Thus, calls where
sync-irq immediately precedes free-irq can be simplified.
However, during this audit several bugs were noticed, where free-irq is
preceded by a "irq >= 0" check... but the sync-irq call is not covered
by the same check.
So, where sync-irq could not be eliminated completely, the missing check
was added.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Correct some arguments in calls to snd_ice1712_gpio_write_bits() from
ap192_set_rate_val().
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Some calls to snd_ice1712_gpio_write() go wrong, if
snd_ice1712_gpio_write_bits() ran before and changed the gpio mask register.
Read the actual gpio value and combine it with the to be set bits in the cpu
instead.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Let "chip reset" become first. Increasement of the "chip reset" related timeout
leads to correctly read eeprom's contents here.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Since unsigned active_offs < 0 is even true when DMAbuf_get_buffer_pointer()
returns negative
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
cs4270_hw_params does several times:
ret = snd_soc_write()
if (ret < 0)
...
This only works when ret is signed.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix the race at reconnection of the device.
The disconnected usb_chip[] must be cleared before the next probe
call properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A little clean up of snd_card_free*().
Removed snd_card_free_prepare() since it's actually almost identical
with snd_card_disconnect().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Move the call of device_unregister() for the card instance in
snd_card_disconnect() to avoid the race of sysfs card entry, which
can be typically found on usb-audio reconnection.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Coding style corrections for burgundy.c.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add mixer controls and correct headphone detection bits for PowerMac
G3 B&W and iMac G3 Tray-loading, both having Burgundy chipset.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Coding style corrections for awacs.c and awacs.h.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add mixer controls and correct headphone detection bits for PowerMacs
7300/7500 (AWACS) and G3 Beige (Screamer), and iMac G3 Slot-loading
(Screamer).
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Coding style corrections for pmac.c.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Enable port change interrupt while initialising AWACS, Screamer, and
Burgundy chipsets.
Signed-off-by: Risto Suominen <Risto.Suominen@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
bps is unsigned, a negative snd_pcm_format_width() return value is not noticed
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The last ALC889A hack may break on some devices with certain model presets
since patch_alc*() have different model tables. So, now it's handled in
the original patch_alc882() but fly to patch_alc883() in model=auto
appropriately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
ALC889A is recognized ALC885/ALC882 but it's actually closer to
ALC888/ALC883.
Cc: Kasper Sandberg <lkml@metanurb.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Several 92hd7xxx and STAC9228 laptops have multiple headphone jacks,
the second headphone jack should be used for the 5.1 surround sound.
Add support for 'Headphone as Line Out' switch, which allows it be used
in 5.1 surround sound.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a pointer for DAC volume TLV data to the model structure so that the
model driver do not need to manually assign it in their control filter.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Initialize the playback volume controls as being muted and having
minimal volume.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add fields for the DAC volume limits to the module structure so that
model drivers do not need to install their own control info handlers.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The empty hifier_mixer_init() function is useless; remove it.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Added the support of AD1989A and AD1989B codecs.
These codecs can have multiple SPDIF devices, but currently we handle
only one SPDIF. If any real devices with two SPDIF interfaces (likely
one for SPDIF and one for HDMI), we'll fix this rightly.
Otherwise, these codecs are pretty similar with AD1988.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix the GPIO 1 mixer control to enable I/O through the front panel
connector of the Xonar DX.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch for snd_usb_caiaq makes sample rates higher dann 48KHz work
with devices which have more than 2 stereo input/output pairs.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch corrects the input channel order of hardware supported by
snd_usb_caiaq.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch fixes potential lockups in snd_usb_caiaq by refining the
locking mechanims and by using usb_kill_urb() in favor to
usb_unlink_urb().
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Leave the power bit for the touch screen alone when suspending the WM9713
so that the touch screen driver can handle it. This allows the touch
screen to be used as a wakeup source when the system is suspended.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
sound: kernel log levels are 0-7
Kernel log levels are 0-7, not 0-9.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This adds support for Quanta IL1 mini-notebook to alsa, defining a new model
for it. It comes with an ALC267 codec chip. Some notes about this model:
* In headphone automute, I use AC_VERB_SET_PIN_WIDGET_CONTROL instead of common
amp mute, to avoid conflict with mixer switch (mixer and automute use the
same nid).
* The only connected capture sources in the hardware are the internal mic and
external mic jack. So instead of using an input source selector like on other
ALC268 models, the mic automute automatically switch between captures.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf, the platform modalias is
prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable sound
platform drivers, to re-enable auto loading.
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Power management support for EAPD enabled laptops, when headphones
are sensed it pulls the EAPD GPIO line low to power it down.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Several laptops have have the SPDIF out defined as 'Digital other out'
when it should be 'SPDIF out' in the default config.
Signed-off-by: Matthew Ranostay <mranostay@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The legacy PC speaker signal was not routed to outputs. The codec is not
prevented from powering down in this patch, although I suppose one could
argue that perhaps it should be. Let me know if anyone feels strongly one
way or the other.
Signed-off-by: Tony Vroon <tony@linx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Please refer to [0003874] on the alsa mantis.
This patch added the pci quirk.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To mute the output of Pin widget 15 in ALC880, we should use the
HDA_OUTPUT. However, current code looks like :
snd_hda_codec_amp_stereo(codec, 0x15, HDA_INPUT, 0, HDA_AMP_MUTE, bits);
It may be a misspelling.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Putting space between ! and variable is a strange coding style, fix
that, also make it fit into 80 columns where that is easy.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
usb audio contains useful debugging code, protected by #if
0. Unfortunately, it will not compile because variable names changed;
fix it.
Dallas workaround is formatted in a way where it is not quite obvious
what is normal code and what is quirk. Reformat it to make it obvious.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Dallas USB speakers are buggy in more than one way. One of configs
they offer does not work at all.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
On Wed, Apr 02, 2008 at 08:19:29AM -0400, Miles Lane wrote:
> [ 48.765906] [ BUG: bad unlock balance detected! ]
> [ 48.765912] -------------------------------------
> [ 48.765918] pulseaudio/4277 is trying to release lock
> (&codec->spdif_mutex) at:
> [ 48.765930] [<c03031b7>] mutex_unlock+0x8/0xa
> [ 48.765945] but there are no more locks to release!
> [ 48.765950]
> [ 48.765952] other info that might help us debug this:
> [ 48.765959] 2 locks held by pulseaudio/4277:
> [ 48.765965] #0: (&pcm->open_mutex){--..}, at: [<f89f134b>]
> snd_pcm_open+0xc1/0x1ba [snd_pcm]
> [ 48.766003] #1: (&chip->open_mutex){--..}, at: [<f8b4f13d>]
> azx_pcm_open+0x36/0x184 [snd_hda_intel]
> [ 48.766057]
> [ 48.766059] stack backtrace:
> [ 48.766066] Pid: 4277, comm: pulseaudio Not tainted 2.6.25-rc8-mm1 #12
> [ 48.766086] [<c013afc6>] print_unlock_inbalance_bug+0xce/0xd8
> [ 48.766107] [<c0109e1c>] ? save_stack_trace+0x1d/0x3b
> [ 48.766130] [<c012f54e>] ? __kernel_text_address+0x1b/0x27
> [ 48.766146] [<c0104533>] ? dump_trace+0xcd/0xd9
> [ 48.766160] [<c0109d9e>] ? save_stack_address+0x0/0x2c
> [ 48.766176] [<c013b80a>] ? find_usage_backwards+0xa4/0xc3
> [ 48.766193] [<c013cfb5>] lock_release_non_nested+0x84/0x120
> [ 48.766209] [<c03031b7>] ? mutex_unlock+0x8/0xa
> [ 48.766222] [<c013d1bb>] lock_release+0x16a/0x199
> [ 48.766238] [<c0303137>] __mutex_unlock_slowpath+0xa9/0x121
> [ 48.766252] [<c03031b7>] mutex_unlock+0x8/0xa
> [ 48.766263] [<f8b4ffd8>] snd_hda_multi_out_analog_open+0xd3/0xef
> [snd_hda_intel]
The following patch should fix it.
Cc: "Miles Lane" <miles.lane@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
WARNING: braces {} are not necessary for single statement blocks
#40: FILE: sound/pci/es1968.c:1831:
+ if (diff > 1) {
+ __maestro_write(chip, IDR0_DATA_PORT, cp1);
+ }
total: 0 errors, 1 warnings, 35 lines checked
./patches/es1968-fix-jitter-on-some-maestro-cards.patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Andreas Mueller <andreas@stapelspeicher.org>
Tested-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch suppresses jitter on several Maestro cards in stereo mode (ALSA of
course).
The patch is also incorporated in the *BSD drivers where I "ported" it from.
Without this patch most of the stereo audio gets out of sync and really
distorted (oss-emulation with mplayer at 48000khz worked somehow).
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
sound/pci/rme9652/hdspm.c has unusually large number of static inline
functions - 22.
I looked through them and some of them seem to be too big to warrant inlining.
This patch removes "inline" from these static functions (regardless of number
of callsites - gcc nowadays auto-inlines statics with one callsite).
Size difference on 32bit x86:
text data bss dec hex filename
20437 2160 516 23113 5a49 linux-2.6-ALLYES/sound/pci/rme9652/hdspm.o
18036 2160 516 20712 50e8 linux-2.6.inline-ALLYES/sound/pci/rme9652/hdspm.o
[coding fix by Takashi Iwai <tiwai@suse.de>]
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When logging register changes in DAPM debug output include the register
number.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Please refer to [0003848] on the alsa mantis.
This patch adds the pci quirk and Mic-Int controller.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
