| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Do not explicity set the default input mode. Use the hardware default
of mode 0 ('Control vinyl'), which is now available.
This reverts commit e3ca4c9.
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
After removing code, only one case remains. So use an 'if' instead.
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This feature was undocumented on early A4DJ units. It is indicated
by lighting both the 'line' and 'phono' lamps at the same time.
Newer units document this and the newer Windows drivers enable this
for all units, so restore the functionality.
This patch simplifies the code and changes the mode mapping to match
the A8DJ, favouring simpler code and consistency over keeping the
existing mapping.
Both 'Control vinyl' and 'Phono' input modes enable the hardware
preamp. The difference is the input impedance.
This reverts commit 9a9527e.
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Mark Hills <mark@pogo.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix a small off-by-one bug which causes the feature unit to announce a
wrong number of channels. This leads to illegal requests sent to the
firmware eventually.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add hd radio blend functions. HPI version inc to 4.03.25.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This request is again handled differently in comparison to UAC1.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
UAC2 devices have their information about pitch control stored in a
different field. Parse it, and emulate the bits for a v1 device.
A new struct uac2_iso_endpoint_descriptor is added.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
-1 is not a good return value as it means -EPERM, "not permitted".
Choose -ENOTSUPP instead, which is what the code really wants to tell
its callers.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a spin_unlock missing on the error path.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E1;
@@
* spin_lock(E1,...);
<+... when != E1
if (...) {
... when != E1
* return ...;
}
...+>
* spin_unlock(E1,...);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6 into fix/asoc
|
|
These should be regular, not linear.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
|
|
These scales should be regular, not linear.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
|
|
These should be regular rather than linear scales.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: stable@kernel.org
|
|
This updates the i.MX SSI driver to make it compatible with the ASoC tree
following the move of DMA parameters from the DAI to the audio substream
object.
Signed-off-by: Stuart Longland <redhatter@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
|
|
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
Add a module option to allow the GPR mixer controls to have the full
resolution of the hardware, i.e., 0...2^31-1 instead of 0...100.
Because of bugs in userspace tools like alsactl and alsamixer, this is
not yet enabled by default.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In the cleanup of the hw_ptr update functions in 2.6.33, the calculation
of the delta value was changed to use the modulo operator to protect
against a negative difference due to the pointer wrapping around at the
boundary.
However, the ptr variables are unsigned, so a negative difference would
result in the two complement's value which has no relation to the actual
difference relative to the boundary; the result is typically some value
near LONG_MAX-boundary. Furthermore, even if the modulo operation would
be done with signed types, the result of a negative dividend could be
negative.
The invalid delta value is then caught by the following checks, but this
means that the pointer update is ignored.
To fix this, use a range check as in the other pointer calculations.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Check that the interrupt raised for a stream is actually a buffer
completion interrupt before handling it as one. Otherwise, memory
errors or FIFO xruns would be interpreted as a pointer update and could
break the stream timing.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
BugLink: https://launchpad.net/bugs/576160
Symptom: Currently (2.6.32.12) the Dell M1730 uses the 3stack model
quirk. Unfortunately this means that capture is not functional out-
of-the-box despite ensuring that capture settings are unmuted and
raised fully.
Test case: boot from Ubuntu 10.04 LTS live cd; capture does not
work.
Resolution: Correct the model quirk for Dell M1730 to rely on the
BIOS configuration.
This patch also trivially sorts the quirk into the correct section
based on the comments.
Reported-and-Tested-By: <picdragon99@msn.com>
Tested-By: Daren Hayward
Tested-By: Tobias Krais
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
First issue:
With the original patch, I've noticed by unmuting the mic
(and even having it muted), there is a distorted("Noise")
coming from the internal speakers, even when the headphones are plugged in.
What my finding's revealed is:
/* Mic (rear) pin: input vref at 80% */
{0x18, AC_VERB_SET_PIN_WIDGET_CONTROL, PIN_VREF80},
{0x18, AC_VERB_SET_AMP_GAIN_MUTE, AMP_OUT_MUTE},
From the original patch. Looking at codec#0 0x18/0x1a is listed as:
Node 0x18 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x90100141: [Fixed] Speaker at Int N/A
Conn = Unknown, Color = Unknown
DefAssociation = 0x4, Sequence = 0x1
Misc = NO_PRESENCE
Pin-ctls: 0x41: OUT VREF_50
Unsolicited: tag=00, enabled=0
Connection: 5
0x0c* 0x0d 0x0e 0x0f 0x26
seems this Node is listed as: [Fixed] Speaker while 0x15
Node 0x15 [Pin Complex] wcaps 0x40018f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x018b3020: [Jack] Line In at Ext Rear
Conn = Comb, Color = Blue
DefAssociation = 0x2, Sequence = 0x0
Pin-ctls: 0x01: VREF_50
Unsolicited: tag=00, enabled=0
Connection: 5
0x0c 0x0d* 0x0e 0x0f 0x26
is [Jack] Line In at Ext Rear.
(looking at the other apple products as examples
I came up with the fix below).
Second issue:
alc885_mbp_4ch_modes
The original patch does a good job with the
HP pin automute function, but from what I noticed is I would have to manually
change the channel form 2 to 4 after plugging the headphones in.
And not to mention having odd moments to where I was jamming out
with the headphones on, then later realized I had sound blasting out
of the speakers as well. My findings revealed that changing
alc885_mbp_4ch_modes to alc885_mba21_ch_modes and setting
- spec->autocfg.speaker_pins[0] = 0x15;
+ spec->autocfg.speaker_pins[0] = 0x18;
gets the automute function when the headphones plugged in working
flawlessly(and the no need to manually change the channel number
afterwards).
Third issue:
alc885_imac91_mixer
There probably doesnt need to be anything changed with this
(esspecially if your one to like lots of sliders),but my findings
revealed that mac osx only has a master on the top right,
another switch on itunes, and then a slider for the mic.
So the changes I did below try and mimic osx as much as possible
(only thing I had an issue with is just having one mute switch
on the master, instead of having two(still investigating)).
fourth issue:
alc882_capture_source
I endeded up creating alc889A_imac91_capture_source()
only because looking at alc882_capture_source I see
that the mic is set to 0x1 while this works, I also noticed
that adding 0x1 and 0x01 and testing that 0x1 somehow
stops working, and 0x01 works(so I figured 0x01 was more
of the alpha of the numbers(still need to figure out
where that valuse is)). In any case the microphone
does work with the original, and with the below patch, but both
still record not as clean(lots of "Noise", which I would like to
look into too).
Note: using alsamixer -Va reveals the capture switches.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
BugLink: https://launchpad.net/bugs/549560
Symptom: on a significant number of hardware, booting from a live cd
results in capture working correctly, but once the distribution is
installed, booting from the install results in capture not working.
Test case: boot from Ubuntu 10.04 LTS live cd; capture works correctly.
Install to HD and reboot; capture does not work. Reproduced with 2.6.32
mainline build (vanilla kernel.org compile)
Resolution: add SSID for Toshiba A100-259 to the position_fix quirk
table, explicitly specifying the LPIB method.
I'll be sending additional patches for these SSIDs as bug reports are
confirmed.
This patch also trivially sorts the quirk table in ascending order by
subsystem vendor.
Reported-and-Tested-by: <davide.molteni@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
BugLink: https://launchpad.net/bugs/583983
Symptom: on a significant number of hardware, booting from a live cd
results in capture working correctly, but once the distribution is
installed, booting from the install results in capture not working.
Test case: boot from Ubuntu 10.04 LTS live cd; capture works correctly.
Install to HD and reboot; capture does not work. Reproduced with 2.6.32
mainline build (vanilla kernel.org compile).
Resolution: add SSID for Acer Aspire 5110 to the position_fix quirk
table, explicitly specifying the LPIB method.
I'll be sending additional patches for these SSIDs as bug reports are
confirmed.
Reported-and-Tested-By: Leo
Cc: <stable@kernel.org>
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use the VENDOR/DEVICE ids provided in pci_ids.h instead of creating
local ids of the same values.
Also, fix the following checkpatch.pl warnings:
WARNING: Use #include <linux/io.h> instead of <asm/io.h>
WARNING: unnecessary whitespace before a quoted newline
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The decoding/encoding is based on own reverse-engineering. Both control and
data ports are handled. Writing to control port supports SysEx events only,
as this is the only type of messages that MPD16 recognizes.
Signed-off-by: Krzysztof Foltman <wdev@foltman.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Commit 7910b4a1db63fefc3d291853d33c34c5b6352e8e in 2.6.34 changed the
runtime->boundary calculation to make this value a multiple of both the
buffer_size and the period_size, because the latter is assumed by the
runtime->hw_ptr_interrupt calculation.
However, due to the lack of a ioctl that could read the software
parameters before they are set, the kernel requires that alsa-lib
calculates the boundary value, too. The changed algorithm leads to
a different boundary value used by alsa-lib, which makes, e.g., mplayer
fail to play a 44.1 kHz file because the silence_size parameter is now
invalid; bug report:
<https://bugtrack.alsa-project.org/alsa-bug/view.php?id=5015>.
This patch reverts the change to the boundary calculation, and instead
fixes the hw_ptr_interrupt calculation to be period-aligned regardless
of the boundary value.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (250 commits)
ALSA: hda: Storage class should be before const qualifier
ASoC: tpa6130a2: Remove CPVSS and HPVdd supplies
ASoC: tpa6130a2: Define output pins with SND_SOC_DAPM_OUTPUT
ASoC: sdp4430 - add sdp4430 pcm ops to DAI.
ASoC: TWL6040: Enable earphone path in codec
ASoC: SDP4430: Add support for Earphone speaker
ASoC: SDP4430: Add sdp4430 machine driver
ASoC: tlv320dac33: Avoid powering off while in BIAS_OFF
ASoC: tlv320dac33: Use dev_dbg in dac33_hard_power function
ALSA: sound/pci/asihpi: Use kzalloc
ALSA: hdmi - dont fail on extra nodes
ALSA: intelhdmi - add id for the CougarPoint chipset
ALSA: intelhdmi - user friendly codec name
ALSA: intelhdmi - add dependency on SND_DYNAMIC_MINORS
ALSA: asihpi: incorrect range check
ALSA: asihpi: testing the wrong variable
ALSA: es1688: add pedantic range checks
ARM: McBSP: Add support for omap4 in McBSP driver
ARM: McBSP: Fix request for irq in OMAP4
OMAP: McBSP: Add 32-bit mode support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (44 commits)
vlynq: make whole Kconfig-menu dependant on architecture
add descriptive comment for TIF_MEMDIE task flag declaration.
EEPROM: max6875: Header file cleanup
EEPROM: 93cx6: Header file cleanup
EEPROM: Header file cleanup
agp: use NULL instead of 0 when pointer is needed
rtc-v3020: make bitfield unsigned
PCI: make bitfield unsigned
jbd2: use NULL instead of 0 when pointer is needed
cciss: fix shadows sparse warning
doc: inode uses a mutex instead of a semaphore.
uml: i386: Avoid redefinition of NR_syscalls
fix "seperate" typos in comments
cocbalt_lcdfb: correct sections
doc: Change urls for sparse
Powerpc: wii: Fix typo in comment
i2o: cleanup some exit paths
Documentation/: it's -> its where appropriate
UML: Fix compiler warning due to missing task_struct declaration
UML: add kernel.h include to signal.c
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (29 commits)
pcmcia: disable PCMCIA ioctl also for ARM
drivers/staging/comedi: dev_node removal (quatech_daqp_cs)
drivers/staging/comedi: dev_node removal (ni_mio_cs)
drivers/staging/comedi: dev_node removal (ni_labpc_cs)
drivers/staging/comedi: dev_node removal (ni_daq_dio24)
drivers/staging/comedi: dev_node removal (ni_daq_700)
drivers/staging/comedi: dev_node removal (das08_cs)
drivers/staging/comedi: dev_node removal (cb_das16_cs)
pata_pcmcia: get rid of extra indirection
pcmcia: remove suspend-related comment from yenta_socket.c
pcmcia: call pcmcia_{read,write}_cis_mem with ops_mutex held
pcmcia: remove pcmcia_add_device_lock
pcmcia: update gfp/slab.h includes
pcmcia: remove unused mem_op.h
pcmcia: do not autoadd root PCI bus resources
pcmcia: clarify alloc_io_space, move it to resource handlers
pcmcia: move all pcmcia_resource_ops providers into one module
pcmcia: move high level CIS access code to separate file
pcmcia: dev_node removal (core)
pcmcia: dev_node removal (remaining drivers)
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM: PM QOS update fix
Freezer / cgroup freezer: Update stale locking comments
PM / platform_bus: Allow runtime PM by default
i2c: Fix bus-level power management callbacks
PM QOS update
PM / Hibernate: Fix block_io.c printk warning
PM / Hibernate: Group swap ops
PM / Hibernate: Move the first_sector out of swsusp_write
PM / Hibernate: Separate block_io
PM / Hibernate: Snapshot cleanup
FS / libfs: Implement simple_write_to_buffer
PM / Hibernate: document open(/dev/snapshot) side effects
PM / Runtime: Add sysfs debug files
PM: Improve device power management document
PM: Update device power management document
PM: Allow runtime_suspend methods to call pm_schedule_suspend()
PM: pm_wakeup - switch to using bool
|
|
Conflicts:
sound/soc/codecs/ad1938.c
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
These pins are for decoupling capacitors for the internal charge pumps
in TPA6130A2 and TPA6140A2 and not for connecting external supply.
Thanks to Eduardo Valentin <eduardo.valentin@nokia.com> for pointing out the
issue with TPA6130A2 and Ilkka Koskinen <ilkka.koskinen@nokia.com> with
TPA6140A2.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Reviewed-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
