| Age | Commit message (Collapse) | Author |
|---|
|
Fix the following compile warning. kctl should be NULL-initialized.
sound/pci/hda/patch_realtek.c: In function ‘alc_build_controls’:
sound/pci/hda/patch_realtek.c:2550:23: warning: ‘kctl’ may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
After mass production started it was found that several boards exhibit
noise problems during sound playback. After some investigation it was
determined that CLKX polarity is set incorrectly, and even if most boards
can tolerate the wrong setting, there are some that don't.
Fix polarity setup in the board file. As the clock settings for input and
output now match, merge in and out functions and structures to simplify
code.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
|
|
Stanse found that in snd_usb_parse_audio_endpoints, there is a
dangling pointer dereference. When snd_usb_parse_audio_format fails,
fp is freed, and continue invoked. On the next loop, there is
"fp && fp->altsetting == 1 && fp->channels == 1" test, but fp is set
from the last iteration (but is bogus) and thus ilegally dereferenced.
Set fp to NULL before "continue".
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
|
|
When SX_TLV widgets are read, if the gain is set to a value below 0dB,
the mixer control is erroniously read as being at maximum volume.
The value read out of the CODEC register is never sign-extended, and
when the minimum value is subtracted (read; added, since the minimum is
negative) the result is a number greater than the maximum allowed value
for the control, and hence it saturates.
Solution: Mask the result so that it "wraps around", emulating
sign-extension.
Signed-off-by: Stuart Longland <redhatter@gentoo.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
* tdm slot has to be configured to get sound working on i.MX25
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Lenovo IdeaPad Y430 has an additional subwoofer connected at pin 0x1b,
which isn't muted when headphone is plugged in. This adds additional
support to the extra subwoofer via new ideapad model.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
These give incorrect results for index wrap on 64 bit.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The config option SND_FSI_AK4642 selects SND_SOC_AK4642 which in turn
enables the compilation of ak4642.c - however this codec uses I2C to
communicate with the HW.
Same applies to DA7210.
Consequently when I2C is not set, the compilation fails [1]
This patch fixes this issues, by adding a depencdency on the related HW-
controller.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Compiling in the MPC5200 sound drivers results in the following build error:
sound/soc/fsl/mpc5200_psc_ac97.o: In function `to_psc_dma_stream':
mpc5200_psc_ac97.c:(.text+0x0): multiple definition of `to_psc_dma_stream'
sound/soc/fsl/mpc5200_dma.o:mpc5200_dma.c:(.text+0x0): first defined here
sound/soc/fsl/efika-audio-fabric.o: In function `to_psc_dma_stream':
efika-audio-fabric.c:(.text+0x0): multiple definition of `to_psc_dma_stream'
sound/soc/fsl/mpc5200_dma.o:mpc5200_dma.c:(.text+0x0): first defined here
make[3]: *** [sound/soc/fsl/built-in.o] Error 1
make[2]: *** [sound/soc/fsl] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
This patch fixes it by declaring the inline function in the header file to
also be a static.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Jon Smirl <jonsmirl@gmail.com>
Tested-by: John Hilmar Linkhorst <John.Linkhorst@rwth-aachen.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The most useful configuration for the WM2000 is to enable the ANC so turn
that on by default, and since we're not reflecting chip default state also
enable the speaker output by default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
|
|
On DA830/OMAP-L137 and DA850/OMAP-L138 SoCs, the McASP peripheral
has FIFO support. This FIFO provides additional data buffering. It
also provides tolerance to variation in host/DMA controller response
times. More details of the FIFO operation can be found at
http://focus.ti.com/general/docs/lit/getliterature.tsp?literatureNumber=sprufm1&fileType=pdf
Existing sequence of steps for audio playback/capture are:
a. DMA configuration
b. McASP configuration (configures and enables FIFO)
c. Start DMA
d. Start McASP (enables FIFO)
During McASP configuration, while FIFO was being configured, FIFO
was being enabled in davinci_hw_common_param() function of
sound/soc/davinci/davinci-mcasp.c file. This generated a transmit
DMA event, which gets serviced when DMA is started.
https://patchwork.kernel.org/patch/84611/ patch clears the DMA
events before starting DMA, which is the right thing to do. But
this resulted in a state where DMA was waiting for an event from
McASP (after step c above), but the event which was already there,
has got cleared (because of step b above).
The fix is not to enable the FIFO during McASP configuration as
FIFO was being enabled as part of McASP start.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
|
|
The line-in input is 0x7 not 0x2 for MacBook (Pro) 5,1 / 5,2 models
Signed-off-by: Alex Murray <murray.alex@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The header contains an extern that isn't used by anything. Remove.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
For RANGE requests, we should only query as much bytes as we're in fact
interested in.
For CUR requests, we shouldn't confuse the firmware with an overlong
request but just ask for 2 bytes.
This might need fixing in the future as it's not entirely clear when to
dispatch 1-byte, 2-byte and 4-byte request blocks. For now, we assume
everything is coded in 16bit - this works for all firmware
implementations I've seen.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Alex Lee <alexlee188@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A device may report its supported sample rates in ranges rather than in
discrete triplets. The code used to only parse the MIN field instead of
properly paying attention to the MAX and RES values.
Also, handle RES values of 1 correctly and announce a continous sample
rate range in this case.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Alex Lee <alexlee188@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Control messages directed to an interface must have the interface number
set in the lower 8 bits of wIndex. This wasn't done correctly for some
clock and mixer messages.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Alex Lee <alexlee188@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
With multiple codec configurations, some codec might have no ADC, thus
it keeps spec->adc_nids = NULL. This causes an Oops in alc_build_controls().
Reference: kernel bug #16156
https://bugzilla.kernel.org/show_bug.cgi?id=16156
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: sound/spi: patch for the unuseful variable removal
ALSA: hda - Add SSID table for iMac7,1.
ALSA: hda - Add SSID table for MacBookAir1,1
ALSA: hda - Add SSID table for MacBookAir2,1
ALSA: atmel: set "channel A event" output to debug
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6164/1: Add kto and kfrom to input operands list.
ARM: 6166/1: Proper prefetch abort handling on pre-ARMv6
ARM: 6165/1: trap overflows on highmem pages from kmap_atomic when debugging
ARM: 6152/1: ux500 make it possible to disable localtimers
[ARM] pxa/spitz: Correctly register WM8750
[ARM] pxa/palmtc: storage class should be before const qualifier
ARM: 6146/1: sa1111: Prevent deadlock in resume path
ARM: 6145/1: ux500 MTU clockrate correction
ARM: 6144/1: TCM memory bug freeing bug
ARM: VFP: Fix vfp_put_double() for d16-d31
|
|
This patch is to change 'auido.h' to 'audio.h' for
fixing nuc900 alsa driver build error.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
|
|
Add support for i2s audio on Bluewater Systems Snapper CL15 module
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The '*bitclk' of structure 'snd_at73c213' seems no use,
so I make a patch to remove the unnecessary variable.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch add's the iMac7,1 SSID entry to
patch_realtek.c which adds sound support.
bug entry:
https://bugs.launchpad.net/mactel-support/+bug/360866
Note:I do not have this machine on hand only
codec#0 file for the machine so please
test if you have the appropriate equipment.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch add's the MacBookAir1,1 SSID entry to
patch_realtek.c which adds sound support.
bug entry:
https://bugs.launchpad.net/mactel-support/+bug/268301
Note:I do not have this machine on hand only
codec#0 file for the machine so please
test if you have the appropriate equipment.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This adds the SSID number to snd_pci_quirk for the
MacBookAir2,1 taken from codec#0 at:
http://launchpadlibrarian.net/49455483/Card0.Codecs.codec.0.txt
keep in mind I do not have one of these machines on hand
so please if you do have this machine please test for me..
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6 into topic/asoc
|
|
This patch to remove the 'break;', when the 'switch' jumps to
the 'default' branch, the 'return -EINVAL' will be return with
a error number, so the 'break;' code never be run, it is unuseful
and should be removed here.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Remove break after return, it is not needed.
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Add ep93xx i2s audio driver
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Upper threshold is used in mode7 of DAC33.
Instead of hard wired UTHR, add control to change the upper threshold
value.
Changing upper threshold is not allowed when the playback is already
running, since wrongly timed change in the UTHR can cause problems
with the codec.
With this control the length of the burst in mode7 can be changed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda-intel - fix wallclk variable update and condition
ALSA: asihpi - Fix uninitialized variable
ALSA: hda: Use LPIB for ASUS M2V
usb/gadget: Replace the old USB audio FU definitions in f_audio.c
ASoC: MX31ads sound support should depend on MACH_MX31ADS_WM1133_EV1
ASoC: Add missing Kconfig entry for Phytec boards
ALSA: usb-audio: export UAC2 clock selectors as mixer controls
ALSA: usb-audio: clean up find_audio_control_unit()
ALSA: usb-audio: add UAC2 sepecific Feature Unit controls
ALSA: usb-audio: unify constants from specification
ALSA: usb-audio: parse clock topology of UAC2 devices
ALSA: usb-audio: fix selector unit string index accessor
include/linux/usb/audio-v2.h: add more UAC2 details
ALSA: usb-audio: support partially write-protected UAC2 controls
ALSA: usb-audio: UAC2: clean up parsing of bmaControls
ALSA: hda: Use LPIB for another mainboard
ALSA: hda: Use mb31 quirk for an iMac model
ALSA: hda: Use LPIB for an ASUS device
|
