| Age | Commit message (Collapse) | Author |
|---|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
|
|
Call the gpio reset platform function instead of using the flawed
ac97 functionality of the MPC5200(b)
From MPC5200B User's Manual:
"Some AC97 devices goes to a test mode, if the Sync line is high
during the Res line is low (reset phase). To avoid this behavior the
Sync line must be also forced to zero during the reset phase. To do
that, the pin muxing should switch to GPIO mode and the GPIO control
register should be used to control the output lines."
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
pcmcia: avoid buffer overflow in pcmcia_setup_isa_irq
pcmcia: do not request windows if you don't need to
pcmcia: insert PCMCIA device resources into resource tree
pcmcia: export resource information to sysfs
pcmcia: use struct resource for PCMCIA devices, part 2
pcmcia: remove memreq_t
pcmcia: move local definitions out of include/pcmcia/cs.h
pcmcia: do not use io_req_t when calling pcmcia_request_io()
pcmcia: do not use io_req_t after call to pcmcia_request_io()
pcmcia: use struct resource for PCMCIA devices
pcmcia: clean up cs.h
pcmcia: use pcmica_{read,write}_config_byte
pcmcia: remove cs_types.h
pcmcia: remove unused flag, simplify headers
pcmcia: remove obsolete CS_EVENT_ definitions
pcmcia: split up central event handler
pcmcia: simplify event callback
pcmcia: remove obsolete ioctl
Conflicts in:
- drivers/staging/comedi/drivers/*
- drivers/staging/wlags49_h2/wl_cs.c
due to dev_info_t and whitespace changes
|
|
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
|
|
|
|
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (48 commits)
Documentation: update broken web addresses.
fix comment typo "choosed" -> "chosen"
hostap:hostap_hw.c Fix typo in comment
Fix spelling contorller -> controller in comments
Kconfig.debug: FAIL_IO_TIMEOUT: typo Faul -> Fault
fs/Kconfig: Fix typo Userpace -> Userspace
Removing dead MACH_U300_BS26
drivers/infiniband: Remove unnecessary casts of private_data
fs/ocfs2: Remove unnecessary casts of private_data
libfc: use ARRAY_SIZE
scsi: bfa: use ARRAY_SIZE
drm: i915: use ARRAY_SIZE
drm: drm_edid: use ARRAY_SIZE
synclink: use ARRAY_SIZE
block: cciss: use ARRAY_SIZE
comment typo fixes: charater => character
fix comment typos concerning "challenge"
arm: plat-spear: fix typo in kerneldoc
reiserfs: typo comment fix
update email address
...
|
|
The NID 0x11 on HP dc5750 with ALC260 should be a speaker although BIOS
gives it as a line-out. This patch adds a quirk to fix the pin config
so that the real line-out is used properly.
Reference: bnc#624118
https://bugzilla.novell.com/show_bug.cgi?id=624118
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
My previous patch assumed that the DMA mode (represented by 3 lowest bits of
ALS4K_GCR99_DMA_EMULATION_CTRL register) is set to the default value 0. If
that's not the case, it might result in invalid mode to be set.
This patch fixes this potential problem.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
PM / Runtime: Add runtime PM statistics (v3)
PM / Runtime: Make runtime_status attribute not debug-only (v. 2)
PM: Do not use dynamically allocated objects in pm_wakeup_event()
PM / Suspend: Fix ordering of calls in suspend error paths
PM / Hibernate: Fix snapshot error code path
PM / Hibernate: Fix hibernation_platform_enter()
pm_qos: Get rid of the allocation in pm_qos_add_request()
pm_qos: Reimplement using plists
plist: Add plist_last
PM: Make it possible to avoid races between wakeup and system sleep
PNPACPI: Add support for remote wakeup
PM: describe kernel policy regarding wakeup defaults (v. 2)
PM / Hibernate: Fix typos in comments in kernel/power/swap.c
|
|
|
|
Enable burst mode to prevent dropouts during high PCI bus usage.
The card is useless in X without this because of dropouts when anything moves
on the screen (at least with PCI VGA card). Enabling this is also recommended
by the datasheet (page 48).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In patch_alc269(), we initialize the primary capsrc so that the device
works from the beginning. It issues CONNECT_SEL verb no matter which
widget is although some widget (e.g. 0x23) has no connection selection
but a mixer, which requires unmuting instead.
This patch fixes the initialization of capsrc by re-using the code as
a helper function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix the ordering problem in DAPM domain, when the user
changes between digital and analog sources during active
capture (or loopback) scenario.
Before this patch, when the user changed from analog source
to digital there were a short time, when the codec enabled
analog mic bias (2.2 volts) instead of the correct digital
mic bias (1.8 volts) to the digital microphones.
This behaviour caused by the former implementation of
selecting the correct type of bias. This was done at the
POST_REG event of the DAPM_MUX_E("TXx Capture Route")
widget.
By moving the bias type selection as DAPM_SUPPLY and
connecting it to the corresponding digimic widget the
problematic situation can be avoided.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
An Intel board needs a white-list entry to enable PC-beep.
Otherwise the driver misdetects (due to bogus BIOS info) and ignores
the PC-beep on 2.6.35.
Reported-and-tested-by: Leandro Lucarella <luca@llucax.com.ar>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Since the pending periods are often bogus and take long time until
actually processed, it often results in a high CPU usage of the hd-audio
workq. Overall it's better to have low CPU consumption by avoiding a
too tight loop rather than the wake-up timing accuracy.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Define constants for the HD-audio stream format bits, and replace the
magic numbers in codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix HDA beep frequency on IDT 92HD73xx and 92HD71Bxx codecs.
These codecs use the standard beep frequency calculation although the
datasheet says it's linear frequency.
Other IDT/STAC codecs might have the same problem. They should be
fixed individually later.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Passing IEC 61937 encapsulated compressed audio at bitrates over 6.144
Mbps (i.e. more than a single 2-channel 16-bit 192kHz IEC 60958 link)
over HDMI requires the use of HBR Audio Stream Packets instead of Audio
Sample Packets.
Enable HBR mode when the stream has 8 channels and the Non-PCM bit is
set.
If the audio converter is not connected to any HBR-capable pins, return
-EINVAL in prepare().
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Set bit 15 (Stream Type) of HDA Stream Format to 1 (Non-PCM) when IEC958
channel status bit 1 (AES0 & 0x02) is set to 1 (non-audio).
This is a prequisite for HDMI HBR passthrough.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Instead of io_req_t, drivers are now requested to fill out
struct pcmcia_device *p_dev->resource[0,1] for up to two ioport
ranges. After a call to pcmcia_request_io(), the ports found there
are reserved, after calling pcmcia_request_configuration(), they may
be used.
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
CC: Michael Buesch <mb@bu3sch.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
After pcmcia_request_io(), do not make use of the values stored in
io_req_t, but instead use those found in struct pcmcia_device->resource[].
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Just as with the X301. The X300 does not have a way to do SPDIF either.
It does not have a dock connector, nor does it have the SPDIF through
the headphone jack.
This patch fixes it so X300 does not show SPDIF, since it cannot do it.
To add all Lenovo Thinkpads had different codec subsytem IDs:
X300:
http://launchpadlibrarian.net/34862838/Card0.Codecs.codec.0.txt
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
the ability to use SPDIF
The Lenovo X301 does not have the ability to connect to a docking
station to use the SPDIF port. It also does not have the ability to do
SPDIF though the headphone jack or Display Port jacks.
This patch fixes it so this is not exposed for the X301 and users do
think it has the ability to do SPDIF.
I tested both headphone & display port jacks and it is not there. I have
tested this patch and it works great.
Also to add the other Thinkpads have different subsystem codec IDs.
Here are examples:
X301:
http://launchpadlibrarian.net/31561902/Card0.Codecs.codec.0.txt
X200:
http://launchpadlibrarian.net/49055036/Card0.Codecs.codec.0.txt
W500:
http://launchpadlibrarian.net/36276057/Card0.Codecs.codec.0.txt
Signed-off-by: Jerone Young <jerone.young@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch fixes the error path in wm9081_register to properly free resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
There is a memory leak found if wm8978_register() fail.
This patch moves the buffer allocate and release
at the same level to prevent the memory leak.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
wm8974 is allocated in wm8974_i2c_probe() but is not freed if wm8974_register()
return -EINVAL (if another WM8974 is registered).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch fixes the error path in wm8961_register to properly free resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch fixes the error path in wm8955_register to properly free resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch adds checking for wm8940_register return value,
and does kfree(wm8940) if wm8940_register() fail.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch includes below fixes:
1. wm8904 need to be kfreed in wm8904_register() error path before return.
2. fix the error path for snd_soc_register_codec() fail and
snd_soc_register_dai() fail to properly free resources.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
wm8711 is allocated in either wm8711_spi_probe() or wm8711_i2c_probe() but is
not freed if wm8711_register() return -EINVAL(if another ad1836 is registered).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
This patch includes below fixes:
1. If another WM8523 is registered, need to kfree wm8523 before return -EINVAL.
2. If snd_soc_register_codec failed, goto error path to properly free resources.
3. Instead of using mixed in-line and goto style cleanup, use goto style error
handling if snd_soc_register_dai failed.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
da7210 should be kfreed if da7210_init() return error.
This patch also fixes the error handing in the case of snd_soc_register_dai()
fail by adding snd_soc_unregister_codec() in error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
ak4642 should be kfreed if ak4642_init() return error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
ad1836 is allocated in ad1836_spi_probe() but is not freed if ad1836_register()
return -EINVAL (if another ad1836 is registered).
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Barry Song <21cnbao@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The WM8741 is a very high performance stereo DAC designed for audio
applications such as professional recording systems, A/V receivers and
high specification CD, DVD and home theatre systems. The device supports
PCM data input word lengths from 16 to 32-bits and sampling rates up to
192kHz. The WM8741 also supports DSD bit-stream data format, in both
direct DSD and PCM-converted DSD modes.
TODO: Expand wm8741_set_dai_sysclk and rate_constraint members to
allow for all supported sample rate / Master Clock frequency combinations.
Fully enable control of supplies.
Signed-off-by: Ian Lartey <ian@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into topic/asoc
|
|
The use of sDMA packet mode in THRESHOLD mode removes the restriction on the
period size.
With the extended THRESHOLD mode user space can ask for any
period size it wishes, and the driver will configure the
sDMA and McBSP FIFO accordingly.
Replace the hw_rule for the period size with static constraint,
which will make sure that the period size will be always
even (to avoid prime period size, which could be possible in
mono stream)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
Utilize the sDMA controller's packet syncronization mode, when
the McBSP FIFO is in use (by extending the THRESHOLD mode).
When the sDMA is configured for packet mode, the sDMA frame size
does not need to match with the McBSP threshold configuration.
Uppon DMA request the sDMA will transfer packet size number of
words, and still trigger interrupt on frame boundary.
The patch extends the original THRESHOLD mode by doing the
following:
if (period_words <= max_threshold)
Current THRESHOLD mode configuration
Otherwise (period_words > max_threshold)
McBSP threshold = sDMA packet size
sDMA frame size = period size
With the extended THRESHOLD mode we can remove the constraint
for the maximum period size, since if the period size is
bigger than the maximum allowed threshold, than the driver
will switch to packet mode, and picks the best (biggest)
threshold value, which can divide evenly the period size.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
To make the code a bit more readable, change the indexed
references to the omap_mcbsp_dai_dma_params elements with
pointer.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
In preparation for the extended threshold mode (sDMA packet mode
support), the code need to be restructured.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
|
|
urb data align
Match usb ids in usb/quirks-table.h for some Hauppage HVR-950Q models
and for the HVR850 model to those ids at the end of au0828-cards.c
Thanks to nhJm449 for pointing out the problem.
Signed-off-by: John S Gruber <JohnSGruber@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Remove cs_types.h which is no longer needed: Most definitions aren't
used at all, a few can be made away with, and two remaining definitions
(typedefs, unfortunatley) may be moved to more specific places.
CC: linux-ide@vger.kernel.org
CC: linux-usb@vger.kernel.org
CC: laforge@gnumonks.org
CC: linux-mtd@lists.infradead.org
CC: alsa-devel@alsa-project.org
CC: linux-serial@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org> (for drivers/bluetooth/)
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
The current ALC259/268/269 parser ignores some pins as unhandled,
but user won't notice what goes wrong. So, added a warning message
for the ignored pins as a hint.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The pin NID 0x1a should be handled as well as NID 0x1b.
Also added comments.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Call snd_hda_shutup_pins() for power-saving and reboot-notifier in
patch_conexant.c as well as other codecs. This will reduce the pop
noise in power-save mode.
Reference: bnc#624896
https://bugzilla.novell.com/show_bug.cgi?id=624896
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
