Age | Commit message (Collapse) | Author |
|
Not all channels have been initialized, so far, especially when aamix
NID itself doesn't have amps but its leaves have. This patch fixes
these holes. Otherwise you might get unexpected loopback inputs,
e.g. from surround channels.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Optional DT property to specify the desired parent clock for the McASP fck
clock.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
An earlier patch overlooked this when the compatible has been changed from
omap2 -> am33x.
Rename omap2_mcasp_pdata to am33xx_mcasp_pdata.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Instead of passing __iomem address (mcasp->base + register_offset) pass
the main mcasp structure and only access the mcasp->base in the low level
IO functions.
In most cases this helps with code readability and it will make it easier
to switch over to regmap in the future.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The IP in DRA7xx is similar to the IP found in TI81xxAM3xxx/AM4xxx type of
SoCs but it is is integrated with sDMA instead of eDMA. The suitable pcm
driver for DRA7xx is the omap-pcm driver which is using dmaengine.
In the driver we can configure both dma related structures used for eDMA and
sDMA. The only thing we need to make sure that we set the correct dma_data
at startup with snd_soc_dai_set_dma_data()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
In synchronous mode both transmit and receive sections are using the TX
clocks. In setup like this the TX clocks need to be enabled when capture
is running.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The audio data to/from McASP can be sent/received via two method:
Via the data port (preferred) or via the configuration bus.
Currently the driver assumes that all data communication will be done via
the data port.
This patch adds support for selecting the configuration port as data
interface.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The FIFO registers base address is different in dm646x compared to newer
SoCs with McASP IP. Instead of using two paths (switch/case) to handle the
difference we can simply pick the correct base address beforehand and use
offsets to address the register we need to configure.
With this change the indentation depth can be reduced as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
davinci_mcasp_set_dai_fmt
Replace mcasp->base use with plain base in the davinci_mcasp_set_dai_fmt()
function since it has been already used by the remaining part of the function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Rename the private struct from davinci_audio_dev to davinci_mcasp.
Change the local use of the pointer to this struct from *dev to *mcasp.
The aim is to have better readable code for the first look since having
dev->xxxx in the code when using the local private struct is a bit
surprising.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
It brings no benefit to inline this function due to it's size and function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
It is not used in the code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Since it is a private struct strictly used by the davinci-mcasp driver it
can be moved from header file to the source file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
It is better for readability to have the register definitions out from the
source file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add .name when assigning the dai name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
These are not used, probably leftovers from the past.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
It is not used outside of the .c file.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Specify the dai formats to use within the snd_soc_dai_link structures. In
this way we can remove the code dealing with the dai format configuration
from the machin driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There's no need to include this header file here.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
AM43xx have the same McASP IP as AM33xx and both platform uses eDMA. Modify
the Kconfig so it will be possible to add audio support for AM43xx based
boards later.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
We have several boards using the same machine driver for audio support.
All of these machines can select a generic machine driver config option to
build the needed driver while keeping the config options used within the
driver for compile time code path selection.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The help text is misleading and the prompt itself explains the purpose of
this config section.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Gen2 has 0 - 9, total 10 channels, not 9 channels.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
On the Dell Inspiron 3045 machine (codec Subsystem Id: 0x10280628),
no external microphone can be detected when plugging a 3-ring
headset. If we add "model=dell-headset-multi" for the
snd-hda-intel.ko, the problem will disappear.
BugLink: https://bugs.launchpad.net/hwe-somerville/+bug/1259437
CC: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
On the Dell Optiplex 3030 machine (codec Subsystem Id: 0x10280623),
no external microphone can be detected when plugging a 3-ring
headset. If we add "model=dell-headset-multi" for the
snd-hda-intel.ko, the problem will disappear.
BugLink: https://bugs.launchpad.net/hwe-somerville/+bug/1259435
CC: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add fields to struct snd_dmaengine_pcm_config to allow custom:
- DMA channel names.
This is useful when the default "tx" and "rx" channel names don't
apply, for example if a HW module supports multiple channels, each
having different DMA channel names. This is the case with the FIFOs
in Tegra's AHUB. This new facility can replace
SND_DMAENGINE_PCM_FLAG_CUSTOM_CHANNEL_NAME.
- DMA device
This allows requesting DMA channels for a device other than the device
which is registering the "PCM" driver. This is quite unusual, but is
currently useful on Tegra. In much HW, and in Tegra20, each DAI HW
module contains its own FIFOs which DMA writes to. However, in Tegra30,
the DMA FIFOs were split out AHUB HW module, which then routes the data
through a cross-bar, and into the DAI HW modules. However, the current
ASoC driver structure does not expose this detail, and acts as if the
FIFOs are still part of the DAI HW modules. Consequently, the "PCM"
driver is registered with the DAI HW module, yet the DMA channels must
be looked up in the AHUB HW module's device tree node. This new config
field allows that to happen. Eventually, the Tegra drivers will be
reworked to fully expose the AHUB, and this config field can be
removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
If snd_dmaengine_pcm_register()'s call to snd_soc_add_platform() fails,
all objects allocated during registration are leaked. Fix this by adding
error-handling code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Restructure the internals of dmaengine_pcm_request_chan_of() as a loop
over all channels to be allocated. This makes it easier to add logic
that applies to all allocated channels, without having to duplicate that
logic in each of the half-duplex/full-duplex paths.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
if codec driver is used for AIC3X_MODEL_3007 the mono iout controls overwrite
registers for class-d amplifier.
classd amplifier controls are only used for AIC3X_MODEL_3007.
Removing all mono snd_kcontrol_new, snd_soc_dapm_widget, snd_soc_dapm_route
and aic3x_init stuff from common code and call only for not AIC3X_MODEL_3007
codecs.
Testet only with AIC3X_MODEL_3007
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch adds a ASoC driver for the AXI-SPDIF softcore. The core implements a
simple SPDIF transmitter and is used on some Analog Devices' reference designs
for various FPGA platforms. For now the driver only support the PL330 as the the
DMA controller.
The driver uses the generic PCM dmaengine driver for its PCM. The only
restriction is that we need to set the SND_DMAENGINE_PCM_FLAG_NO_RESIDUE flag as
the dmaengine driver for the DMA core (PL330) that is used with this core has no
residue reporting capabilities yet. This will be fixed in the future though.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch adds support for the AXI-I2S softcore. The core implements a simple
bidirectional I2S transceiver and is used by Analog Devices in some of their
reference designs for various FPGA platforms.
The driver uses the generic PCM dmaengine driver for its PCM. The only
restriction is that we need to set the SND_DMAENGINE_PCM_FLAG_NO_RESIDUE flag as
the dmaengine driver for the DMA core (PL330) that is used with this core has no
residue reporting capabilities yet. This will be fixed in the future though.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
If we update it here, the set_bias_level() of Codec driver won't be normally
called and we will then miss some essential procedures in set_bias_level() of
the Codec driver. Thus drop it.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
In tegra*_i2s_set_fmt(), in the (fmt == SND_SOC_DAIFMT_CBM_CFM) case,
"val" is never assigned to, but left uninitialized. The other case does
initialized it. Fix this by initializing val at the start of the
function, and only ever ORing into it.
Update the handling of "mask" so it works the same way for consistency.
Update tegra20_spdif.c to use the same code-style for consistency, even
though it doesn't happen to suffer from the same problem at present.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes: 0f163546a772 ("ASoC: tegra: use regmap more directly")
Cc: <stable@vger.kernel.org>
|
|
Since there are more HD-audio compatible codecs, move the definitions
of HD-audio verbs into common header location, include/sound, so that
it can be included cleanly from other drivers than HD-audio driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
AD and VIA codecs had stereo mixer input enabled as default before
moving to the generic parser, and people think the lack of such a
regression. In this patch, the stereo mixer input is added back to
the input selection if no auto-mic is available, and if it's not
disabled explicitly via hint. This should satisfy most of demands,
i.e. stereo mix on desktop machines like what it worked before, and it
still keeps the new auto-mic feature on laptops.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Sometimes the hardware reports LPIB being advanced than POSBUF.
When this happens, the driver adjusts to a positive value by adding
the buffer size. Then the driver detects it as an error (greater than
the period size), and stops the LPIB delay account from this point
on.
When I took a close look at these conditions, the values shown are all
very small numbers, and it'd be better to just ignore these values
instead of discontinuing the LPIB delay correction.
In this patch, the driver checks a negative delay value and ignores if
it's a significantly small error. Currently the threshold is set to
64 frames, but could be smaller.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The loopback mixing paths aren't initialized correctly at init
callback. Mostly this is harmless as codecs usually set the mute
state as default, but we still should make sure.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We have blindly assumed that all valid configurations should have
either analog or digital playback, but there can be capture-only
configurations. The parser shouldn't escape in such a case.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch skips the default depop delay before D3 for Haswell (10 ms) and
Valleyview2 (100 ms) display codec, to reduce codec suspend time.
The analog part of display audio is implemented in the external display. Some
displays have weak pop noise while others not when suspending, no matter there
is the default delay or not.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
I've tested the old Dell Vostro 131 with the latest generic parser
and it works just fine, and as a bonus we get better jack detection
features in userspace. Therefore this quirk can be removed.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This simplifies lots of codes indeed.
Tested-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fix the following warning when optimizing for size with gcc-4.6.4:
sound/usb/mixer_quirks.c:1514:6: warning: 'err' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
DSPCLK_DIV can be only generated correctly after enabling SYSCLK. But if the
current bias_level hasn't reached SND_SOC_BIAS_ON, DAPM won't enable SYSCLK,
which would cause the calculation result from DSPCLK_DIV invalid since bit
DSPCLK_DIV will be finally turned to its true value after DAPM enables SYSCLK
while the driver won't calculate it again for the current instance. In this
circumstance, a playback which needs non-zero DSPCLK_DIV would be distorted
due to unexpected clock frequency resulted from an invalid DSPCLK_DIV value.
So this patch provisionally enables the SYSCLK to get a valid DSPCLK_DIV for
calculation and then disables it afterward.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Initially, this binding and driver only describe/support playback to
headphones and speakers, and capture from the external microphone, with
GPIO-based jack detection for the headphone jack only.
This driver is useful for the Venice2 board.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch add quirk for Acer Aspire E-572:
- fix external mic
- limit mic boost for internal mic with maximal noise level of -24dB
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This will allow a marginal speed improvement when used with a bus that
supports async I/O by reducing the amount of context thrashing between
writes, allowing the bus to be more fully utilised.
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
MacBook Air 2,1 has a fairly different pin assignment from its brother
MBA 1,1, and yet another quirks are needed for pin 0x18 and 0x19,
similarly like what iMac 9,1 requires, in order to make the sound
working on it.
Reported-and-tested-by: Bruno Prémont <bonbons@linux-vserver.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Change sam9x5 with wm8731 work in DSP A mode, this will fix the
left/right channel swap issue.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|