summaryrefslogtreecommitdiffstats
path: root/sound
AgeCommit message (Collapse)Author
2013-11-29ASoC: core: Use consistent byte ordering in snd_soc_bytes_getCharles Keepax
snd_soc_bytes_put treats the data in the binary control as big endian words, however snd_soc_bytes_get uses the endian of the host machine. This causes the two functions to be inconsistant with how the mask is applied on little endian machines. This patch applies the big_endian format used in snd_soc_bytes_put to snd_soc_bytes_get. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-29ALSA: hda - allow a codec to define its own depop delay timeMengdong Lin
This patch adds 'depop_delay' to struct hda_codec, to indicate a depop delay time in ms when power-down, in function set_power_state() to D3. Default value is -1, for a default delay time. Machine fixup can set a suitable value according to the codec chip and HW audio design. Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-11-29ALSA: hda - fixup ALC262 to remove depop delay on Intel BayleyBay boardMengdong Lin
This patch defines a fixup 'alc_fixup_no_depop_delay', which sets alc_spec flag 'no_depop_delay' to indicate skipping delay in Realtek codec suspend/resume. And Intel Baytrail BayleyBay board applies this fixup to reduce driver suspend/resume time. Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-11-29ALSA: hda/realtek - Remove depop delay for suspend and resume if applicableKailang Yang
This patch defines a flag "no_depop_delay" in alc_spec. If this flag is set, delay in alc_eapd_shutup and alc_resume will be skipped. Machine-specific fixup can set this flag to reduce suspend/resume time, if the codec and hardware analog design can avoid pop noise without this delay. Signed-off-by: Kailang Yang <kailang@realtek.com> Signed-off-by: Mengdong Lin <mengdong.lin@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-11-29ALSA: hda/realtek - Add more codecs alias name for DellKailang Yang
Dell assigned alias name for more codecs. ALC3220 ALC3221 ALC3223 ALC3226 ALC3234 ALC3661. Signed-off-by: Kailang Yang <kailang@realtek.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-11-29ASoC: cs42l52: Fix buildMark Brown
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-29ASoC: rcar: add Gen2 sound supportKuninori Morimoto
This patch adds Gen2 sound support for Renesas R-Car. But, it is supporting PIO transfer only at this point Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-29ASoC: rcar: remove rcar_gen_opsKuninori Morimoto
Current rcar driver gen.c is using rcar_gen_ops which was made with the assumption that Gen1 and Gen2 need different behavior. but it was not needed. This patch removes unnecessary complex method. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-29ASoC: rcar: remove .path_init/exit from rsnd_gen_opsKuninori Morimoto
rsnd_gen_ops has .path_init/exit callback function which cares SRU/SSI (if Gen1) SCU/SSIU/SSI (if Gen2) path settings. But, the differences between Gen1/Gen2 are cared in ssi.c/scu.c, and the path itself is same in Gen1/Gen2. This patch removes .path_init/exit callback. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-29ASoC: rcar: add rsnd_is_accessible_reg()Kuninori Morimoto
Current rcar driver is supporting Gen1, and Gen2 will be supported soon. Then, some registers are used from Gen1 only, or from Gen2 only. To avoid NULL pointer access, this patch adds register accessible check function. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-29ASoC: rcar: separate regmap init common fieldKuninori Morimoto
The repmap initialization difference between Gen1/Gen2 is only register offset. This patch separates rsnd_gen1_regmap_init() into common part and Gen1 specific part. Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-29ASoC: rcar: remove unused register settingsKuninori Morimoto
AUDIO_CLK_SEL4/5 are not used Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-29ALSA: dice: fix array limits in dice_proc_read()Dan Carpenter
The array limits are supposed to be in units of u32 instead of in bytes. The current code has a potential array overflow. Fixes: c614475b0ea9 ('ALSA: dice: add a proc file to show device information') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-11-29ALSA: hda - Add mono speaker quirk for Dell Inspiron 5439David Henningsson
This machine also has mono output if run through DAC node 0x03. Cc: stable@vger.kernel.org (v3.10+) BugLink: https://bugs.launchpad.net/bugs/1256212 Tested-by: David Chen <david.chen@canonical.com> Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-11-28ASoC: wm_adsp: Stop region iteration when the desired region is foundCharles Keepax
When locating the memory region relating to a coefficient block written through a bin file we keep processing the list of regions even after we have found the region we require. This patch adds a break, so we don't process redundant list items. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-28ALSA: hda - Add LFE chmap to ASUS ET2700Takashi Iwai
As the previous commit 1f0bbf03cb82 added the pin config for the bass speaker, this patch adds the corresponding LFE-only channel map on ASUS ET2700. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65961 Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-11-28ALSA: hda - Initialize missing bass speaker pin for ASUS AIO ET2700Takashi Iwai
Add a fixup entry for the missing bass speaker pin 0x16 on ASUS ET2700 AiO desktop. The channel map will be added in the next patch, so that this can be backported easily to stable kernels. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65961 Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-11-28ASoC: spear: Use devm_snd_dmaengine_pcm_registerLars-Peter Clausen
Makes the code slightly shorter. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Rajeev Kumar <rajeev-dlh.kumar@st.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-28ASoC: Add resource managed snd_dmaengine_pcm_register()Lars-Peter Clausen
For many drivers using the generic dmaengine PCM driver one of the few (or the only) things left to do in the drivers remove function is to unregister the PCM device. This patch adds a resource managed version of snd_dmaengine_pcm_register() which makes it possible to simplify the remove function as well as the error path in the probe function for those drivers. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-28ASoC: cs42l52: Add devicetree support for CS42L52Brian Austin
This patch adds device tree support for the CS42L52 Codec Signed-off-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-28Merge branch 'for-linus' into for-nextTakashi Iwai
2013-11-28ALSA: hda - limit mic boost on Asus UX31[A,E]Oleksij Rempel
This both devices need limit for internal dmic. [cosmetic change; renamed fixup name by tiwai] Signed-off-by: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-11-28ALSA: hda - Check leaf nodes to find aamix ampsTakashi Iwai
The current generic parser assumes blindly that the volume and mute amps are found in the aamix node itself. But on some codecs, typically Analog Devices ones, the aamix amps are separately implemented in each leaf node of the aamix node, and the current driver can't establish the correct amp controls. This is a regression compared with the previous static quirks. This patch extends the search for the amps to the leaf nodes for allowing the aamix controls again on such codecs. In this implementation, I didn't code to loop through the whole paths, since usually one depth should suffice, and we can't search too deeply, as it may result in the conflicting control assignments. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=65641 Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-11-28ASoC: cs42l52: Make MICA/B mixer dependent on mic configBrian Austin
MICA/B Single-Ended input selection depends on mica/b config so lets make the mixer controls for them only show for selected mic's Signed-off-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-28ASoC: cs42l52: Reorganize MICA/B Config and SelectBrian Austin
This patch reworks the MICA an MICB config for single-ended or differential and the selection of which MIC for the single config Signed-off-by: Brian Austin <brian.austin@cirrus.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: cs42l52: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm9081: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27AsoC: wm9081: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm8988: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm8985: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm8983: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm8900: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm8804: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm8776: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm8994: Move DCS done IRQ request laterwangbiao
once code return from request_threaded_irq, irq was setup enabled by default, but completion var dcs_done not got initialized yet, if then a dcs done irq was raised, system will got hung as the sync mechanism is invalid now. so this patch move dcs done irq request to the end of initialization of completion. Signed-off-by: wang, biao <biao.wang@intel.com> Signed-off-by: Zhang, Di <di.zhang@intel.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm8753: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm8750: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm8741: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm8737: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm8731: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: ssm2602: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: da7210: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: cs4271: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: kirkwood: Fix erroneous double output while playingJean-Francois Moine
This patch fixes the setting of the register KIRKWOOD_PLAYCTL which did always streaming on both I2S and SPDIF, ignoring the DAI ID. The bug was introduced by the commit 75b9b65ee5a "ASoC: kirkwood: add S/PDIF support" Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: kirkwood: Fix invalid S/PDIF formatJean-Francois Moine
This patch removes the 32 bits format which is not supported by S/PDIF output. Signed-off-by: Jean-Francois Moine <moinejf@free.fr> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: soc-io: Use IS_ENABLED() macroFabio Estevam
Using the IS_ENABLED() macro can make the code shorter and simpler. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: pcm: Always honor DAI min and max sample rate constraintsLars-Peter Clausen
snd_pcm_limit_hw_rates() will initialize the minimum and maximum sample rate for the PCM stream based on the rates specified in the rates field. Since we call snd_pcm_limit_hw_rates() after soc_pcm_init_runtime_hw() it will essentially overwrite the min and max rate set in soc_pcm_init_runtime_hw(). This may cause the minimum or maximum rate to be set to a value outside the range of one of the components if one of the components sets either SNDRV_PCM_RATE_CONTINUOUS or SNDRV_PCM_RATE_KNOT and the other component specified a discrete rate via SNDRV_PCM_RATE_[0-9]* that is outside of the first component's rate range. To fix this first calculate the minimum and maximum rates using snd_pcm_limit_hw_rates() and then on top of that apply the contraints specified in the snd_soc_pcm_stream structs. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Takashi iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: pcm: Fix rate_max calculationLars-Peter Clausen
In order to make sure that the sample rate is in the supported range of both components the maximum rate of the card should be the minimum of the maximum rate of each components. There is one special case to consider though, if max_rate is set to 0 this means there is no maximum specified, so use min_not_zero() macro which will give use the desired result. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Takashi iwai <tiwai@suse.de> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: wm5110: Remove output OSR and PGA volume controlsCharles Keepax
These are managed automatically in current revisions. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@linaro.org>
2013-11-27ASoC: atmel: sam9x5_wm8731: fix oops when unload moduleBo Shen
As the priv is not assigned to card->drvdata, it is NULL, so when unload module, it will cause NULL pointer oops. Assign priv to card->drvdata to fix this issue. Signed-off-by: Bo Shen <voice.shen@atmel.com> Signed-off-by: Mark Brown <broonie@linaro.org>