| Age | Commit message (Collapse) | Author |
|---|
|
Currently in snd_soc_instantiate_card() we only check if the aux dev exists, but
do not yet assign it to its rtd. This means that we need to lookup the aux dev
again in soc_probe_aux_dev(). This patch changes the behavior to assign the aux
dev to the rtd in soc_check_aux_dev() (and renames it to soc_bind_aux_dev()).
This simplifies the implementation a bit and also removes the need for
soc_post_component_init() to know about the specific CODEC that was assigned to
the rtd. The later is necessary for componentization as the code should work for
all types of components not just CODECs. This new behavior is also more in sync
with how soc_bind_dai_link()/soc_probe_link_dais() works.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
soc_find_matching_codec() works in the same way as soc_find_codec() except that
it only works for auxdevs. It can easily be replaced by the generic
soc_find_codec().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
rtd->codec is already initialized in soc_bind_dai_link(), so there is no need to
do it again in soc_dai_link_init(). Removing the rtd->codec initialization from
soc_dai_link_init() also removes the need for soc_dai_link_init() to know about
the CODEC at all.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch adds a minimum support of Realtek ALC5670 codec.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Now, DVC can use DT
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
R-Car sound uses Audio DMAC and Audio DMAC peri peri.
Audio DMAC peri peri transfers data inside circuit.
DMA transfer needs source / destination address,
and destination address can be set via dmaengine_slave_config().
The source address can be set when starting DMAEngine.
Because Audio DMAC peri peri always ignores its value,
current driver always used same source address for
Audio DMAC / Audio DMAC peri peri
(Audio DMAC peri peri source / destination address
is always fixed value)
But, This is not good match for DT booting.
This patch properly uses DMA start address
for Audio DMAC / Audio DMAC peri peri.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Current R-Car sound SSI/SRC/DVC selection has feature limit.
(It is assuming that SSI/SRC are using same index number)
So that enabling SSI/SRC flexible selection,
this patch modifies DMA settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Refactor the function to facilitate the migration to
multiple codecs.
Fix a trailing space in the header as well.
No functional change.
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Since multiple codecs DAI will be usable in the future, remove
explicit unique codec_dai and cpu_dai parameters.
Replace them with snd_soc_pcm_runtime pointer that will contain
every instances.
No functionale change.
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
'status' is not used in the function. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Tested-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
'err' is not used in the function. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
'chip' is not used in the function. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The "list" field has been omitted from struct azx, but its
initialization remained mistakenly in hda_tegra.c, which leads to a
compile error:
sound/pci/hda/hda_tegra.c: In function 'hda_tegra_create':
sound/pci/hda/hda_tegra.c:481:22: error: 'struct azx' has no member
named 'list'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 9a34af4a3327 ('ALSA: hda - Move more PCI-controller-specific stuff from generic code')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
'prev' is not used in the function. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
'private_data' is not used in the function. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
I received a report this morning from one of the Novena developers that
the behaviour of the iMX6 ASoC codec driver (using imx-pcm-dma.c) was
sub-optimal under high system load.
While there are issues relating to system load remaining, upon reviewing
the ASoC imx-pcm-dma.c driver, it was noticed that it not using the
residue support, because SDMA doesn't support it. This has the effect
that SDMA has to make multiple calls into the ASoC and ALSA code, one
for each period.
Since ALSA's snd_pcm_elapsed() does not need to be called multiple times
and it is entirely sufficient to call it once to update ALSA with the
current buffer position via the pointer method, we can do better here.
We can also avoid stopping the DMA entirely, just like real cyclic DMA
implementations behave. While this means that we replay some old samples,
this is a nicer behaviour than having audio stop and restart.
The changes to achieve this are relatively minor - imx-sdma.c can track
where the DMA is to the nearest descriptor boundary - it does this
already when deciding how many callbacks to issue. In doing this,
buf_tail always points at the descriptor which will complete next.
The residue is defined by the bytes remaining to the end of the buffer,
when the buffer is viewed as a single block of memory [start...end].
So, when we start out, there's a full buffer worth of residue, and this
counts down as we approach the end of the buffer, eventually becoming
zero at the end, before returning to the full buffer worth when we
wrap back to the start.
Moving the walking of the descriptors into the interrupt handler means
that we can update the BD_DONE flag at interrupt time, thus avoiding
a delayed tasklet stopping the cyclic DMA.
This means that the residue can be calculated from (total descriptors -
buf_tail) * descriptor size. This is what the change below does. We
update imx-pcm-dma.c to remove the NO_RESIDUE flag since we now provide
the residue.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This renames all the local <mach/gpio.h> headers in the S5P platforms
to <mach/gpio-samsung.h> indicating a scope local to this platform,
and cuts the implicit inclusion of <mach/gpio.h> from <linux/gpio.h>
by removing the use of NEED_MACH_GPIO_H from all S5P variants.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Peach-pi board has MAX98091 CODEC. Extend snow machine driver to support
this board.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The MAX98091 CODEC is the same as MAX98090 CODEC, but with an extra
microphone. Existing driver for MAX98090 CODEC already has support
for MAX98091 CODEC. Adding proper compatible string so that MAX98091
CODEC can be specified from device tree.
Signed-off-by: Wonjoon Lee <woojoo.lee@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The implementation of rt5677_pll_calc() has the same logic of rl6231_pll_calc().
The only difference is the lower boundary checking for freq_in.
This patch calls rl6231_pll_calc() instead of open-coded.
The k_bp of struct rt5677_pll_code is always false, thus also remove the
code to check pll_code.k_bp.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
In case of S24_LE/U24_LE modes we expect 24bits on the bus while the samples
are stored and transferred in memory on 32bits (lower 3 bytes of the 4
bytes).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The codec need to be configured to 24bit mode in case of S24_LE format.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Correct the hw_params callback to configure the codec correctly in case of
S24_3LE format since in case of S24_3LE the codec has been configured to
16bit format mode.
S24_LE is not defined as supported format for the codec.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The recent commit [6194b99d: ALSA: hda - Kill the rest of snd_print*()
usages] changed the callback map_slaves(), but one call was forgotten
to be replaced due to the cast, which leads to kernel Oops due to
invalid function. This patch replaces it with a proper function.
Fixes: 6194b99de9f5 ('ALSA: hda - Kill the rest of snd_print*() usages')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The cs4265_volatile_register reutrns a bool. The function now returns
true or false vs 1 and 0.
Signed-off-by: Paul Handrigan <Paul.Handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Conflicts:
sound/soc/soc-core.c
|
|
Current DVC can be enabled only when playback,
but, this came from misunderstanding.
It is not correct.
DVC <-> DMA relationship is...
Playback: MEM -> DMAC -> SRC -> DVC -> DMACp -> SSI
Capture: SSI -> DMACp -> SRC -> DVC -> DMAC -> MEM
DVC can be used for both Playback/Capture
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Current R-Car sound driver is using DMAEngine directly,
but, ASoC is requesting to use common DMA transfer method,
like snd_dmaengine_pcm_trigger() or dmaengine_pcm_ops.
It is difficult to switch at this point, since Renesas
driver is also supporting PIO transfer.
This patch uses dmaengine_prep_dma_cyclic() instead
of dmaengine_prep_slave_single().
It is used in requested method,
and is good first step to switch over.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Sound data needs to be sent to R-Car sound SSI when playback.
But, there are 2 interfaces for it.
1st is SSITDR/SSIRDR which are mapped on SSI.
2nd is SSIn_BUSIF which are mapped on SSIU.
2nd SSIn_BUSIF is used when DMA transfer,
and it is always used if sound data came from via SRC.
But, we can use it when SSI+DMA case too.
(Current driver is assuming 1st SSITDR/SSIRDR for it)
2nd SSIn_BUSIF can be used as FIFO.
This is very helpful/useful for SSI+DMA.
But DMA address / DMA ID are not same between 1st/2nd cases.
This patch care about these settings.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Current FSI driver is using DMAEngine directly,
but, ASoC is requesting to use common DMA transfer method,
like snd_dmaengine_pcm_trigger() or dmaengine_pcm_ops.
It is difficult to switch at this point, since Renesas
driver is also supporting PIO transfer.
This patch uses dmaengine_prep_dma_cyclic() instead
of dmaengine_prep_slave_single().
It is used in requested method,
and is good first step to switch over.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
fsi PIO/DMA handler are using each own pointer update method,
but these can be share.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Current fsi driver is using SNDRV_DMA_TYPE_CONTINUOUS
for snd_pcm_lib_preallocate_pages_for_all().
But, it came from original dma-sh7760.c,
and no longer needed.
This patch exchange its parameter, and removed
original dma mapping and un-needed
dma_sync_single_xxx() from driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
|
|
Avoid creating duplicate directories by prefixing codecs and platforms
with their separate identifiers. This avoids snd-soc-dummy (which can
appear both as a dummy platform and a dummy codec on the same card)
from clashing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Permit ALSA to run without hardware interrupts from the audio interface.
Instead, ALSA will use a kernel timer to decide when to check the buffer
state, resulting in a lighter workload for the CPU.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
There is no hardware restriction requiring a minimum of 8 periods, or
a minimum of 2048 bytes in a period. Let's drop these values so that
userspace has more flexibility in choosing these parameters.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
We still see the occasional timeout waiting for busy to clear. As the
spec is contradictory, and we know that the current implementation
doesn't work, try an alternative interpretation from the spec. This
one appears to work - I have yet to find any issue with it during my
testing over several months.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The spec requires that the mute bits must be set while the channel
is disabled. Ensure that this is the case by providing a helper
which ensures that the appropriate mute bit is set while the enable
bit is clear.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Since we wish to disable capture inputs for some formats, we need to
ensure that we clear the enable bits in our cached record control
register. This seems to have been missed, resulting in the register
only accumulating enable bits.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Add a KIRKWOOD_RECCTL_ENABLE_MASK definition to complement the existing
PLAYCTL definition, and make use of it where we wish to clear both
enable bits.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Also add const to array
text data bss dec hex filename
10946 2904 3528 17378 43e2 sound/soc/codecs/wm0010.o-before
10891 2840 3512 17243 435b sound/soc/codecs/wm0010.o-after
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Let memory subsystem handle the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Let memory subsystem handle the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Let memory subsystem handle the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Let memory subsystem handle the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Let memory subsystem handle the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Let memory subsystem handle the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Let memory subsystem handle the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Let memory subsystem handle the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
