summaryrefslogtreecommitdiffstats
path: root/sound
AgeCommit message (Collapse)Author
2012-09-27ASoC: wm5110: Adding missing volume update bitsCharles Keepax
The volume update bits were being set on all but one input and one output. Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Cc: stable@vger.kernel.org
2012-09-26ASoC: wm5110: Add OUT3R supportMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-26ASoC: wm5110: Add AEC loopback supportMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-26ASoC: wm5110: Rename EPOUT to HPOUT3Mark Brown
The third output on WM5110 is a general purpose headphone output which can be used to drive an earpice rather than a dedicated earpiece driver. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-26ASoC: arizona: Add more clock ratesMark Brown
Some devices support additional clock rates. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-26ASoC: arizona: Add more DSP options for mixer input muxesMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-26ASoC: wm0010: Initialise chip state before we register the interruptMark Brown
The interrupt handler uses the chip state. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-26ASoC: wm0010: Don't check if reset GPIO is defined when removingMark Brown
We will fail to probe without one. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-26ASoC: wm0010: Allow slow GPIO for resetMark Brown
We never set the GPIO from atomic context so there's no reason why we can't support a GPIO that needs to sleep when configuring. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-26ASoC: wm5110: Enable bypass mode for MICVDDMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-26ASoC: wm5102: Enable bypass mode for MICVDDMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-26ASoC: dapm: Allow regulators to bypass as well as disable when idleMark Brown
Allow regulators managed via DAPM to make use of the bypass support that has recently been added to the regulator API by setting a flag SND_SOC_DAPM_REGULATOR_BYPASS. When this flag is set the regulator will be put into bypass mode before being disabled, allowing the regulator to fall into bypass mode if it can't be disabled due to other users. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-25ASoC: cs4270: Remove mono supportFabio Estevam
According to cs4270 datasheet, there is no reference to mono mode. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Timur Tabi <timur@freescale.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22Merge remote-tracking branch 'asoc/topic/ux500' into for-3.7Mark Brown
2012-09-22ASoC: wm2000: Add regulator supportMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: wm2000: Convert to devm_regmap_init_i2c()Mark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22Merge tag 'v3.6-rc6' into for-3.7Mark Brown
Linux 3.6-rc6 has all our bug fixes. Conflicts (trivial overlap): sound/soc/omap/am3517evm.c
2012-09-22ASoC: twl4030: Support for DT booted kernelPeter Ujfalusi
When the kernel has been booted with DT blob the platform data is NULL for the driver. We need to construct the pdata based on the DT information for runtime use. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: twl4030: Add pointer to pdata within the private dataPeter Ujfalusi
Access the pdata via a pointer within the twl4030_priv structure. In preparation for DeviceTree support. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: twl4030: Convert to use devm_kzallocPeter Ujfalusi
Allocate the private data with devm_kzalloc. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC/mfd: twl4030: Remove set_hs_extmute callback from platform dataPeter Ujfalusi
We no longer have users for the set_hs_extmute callback which has been replaced by hs_extmute_gpio so the codec driver can handle the external mute if it is needed by the board. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ARM: OMAP/ASoC: Zoom2: Let the codec to handle the hs_extmute GPIOPeter Ujfalusi
Remove the use of set_hs_extmute callback and let the codec driver to handle the extmute GPIO. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: twl4030: Move hs_extmute GPIO handling to driverPeter Ujfalusi
The external mute (if it is in use) is handled by a GPIO line. Prepare to remove the set_hs_extmute callback and replace it with: hs_extmute_gpio: the GPIO number to use for external mute When the users of set_hs_extmute has been converted the callback can be removed. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: omap-pcm: Convert to use dmaenginePeter Ujfalusi
Original author: Russell King <rmk+kernel@arm.linux.org.uk> Switch the omap-pcm to use dmaengine. Certain features are not supported by after dmaengine conversion: 1. No period wakeup mode DMA engine has no way to communicate this information through standard channels. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: OMAP: mcbsp, mcpdm, dmic, hdmi: Set dma_data at startup timePeter Ujfalusi
Set the dma_data for the stream (snd_soc_dai_set_dma_data) at dai_startup time so omap-pcm will have access to the needed information regarding to the DMA channel earlier. This is needed for the clean dmaengine support. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: omap-pcm, omap-dmic: Change the use of omap_pcm_dma_data->data_typePeter Ujfalusi
Instead of the OMAP DMA data type definition the data_type will be used to specify the number of bits the DMA word should be configured or 0 in case when based on the stream's format the omap-pcm can decide the needed DMA word size. This feature is needed for the omap-hdmi where the sDMA need to be configured for 32bit word type regardless of the audio format used. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: OMAP: mcbsp, mcpdm, dmic: Let omap-pcm to pick the dma_typePeter Ujfalusi
omap-pcm can figure out the correct dma_type based on the stream's format. In this way we can get rid of the plat/dma.h include from these drivers. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: omap-mcpdm: Use platform_get_resource_* to get resourcesPeter Ujfalusi
Get the needed resources in a correct way and avoid using defines for them. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: omap-pcm: Prepare to configure the DMA data_type based on stream ↵Peter Ujfalusi
properties Based on the format of the stream the omap-pcm can decide alone what data type should be used with by the sDMA. Keep the possibility for OMAP dai drivers to tell omap-pcm if they want to use different data type. This is needed for the omap-hdmi for example which needs 32bit data type even if the stream format is S16_LE. The check if (dma_data->data_type) is safe at the moment since omap-pcm does not support 8bit samples (OMAP_DMA_DATA_TYPE_S8 == 0x00). The next step is to redefine the meaning of dma_data->data_type to unblock this limitation. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: OMAP: Remove sync_mode from omap_pcm_dma_data structPeter Ujfalusi
The omap-pcm platform driver no longer needs this parameter to select between ELEMENT and PACKET mode. The selection is based on the configured packet_size. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: omap-pcm: Select sDMA synchronization based on packet_sizePeter Ujfalusi
Since we only have element or packet synchronization we can use the dma_data->packet_size to select the desired mode: if packet_size is 0 we use ELEMENT mode if packet_size is not 0 we use PACKET mode for sDMA synchronization. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: omap-mcbsp: Use sDMA packet mode instead of frame modePeter Ujfalusi
When McBSP is configured in threshold mode we can use sDMA packet mode in all cases. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: fsl: register the wm9712-codecEric Millbrandt
The mpc5200-psc-ac97 driver does not enumerate attached ac97 devices, so register the device here. Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: fsl: pcm030-audio-fabric use snd_soc_register_cardEric Millbrandt
Convert pcm030-audio-fabric to use the new snd_soc_register_card api instead of the older method of registering a separate platform device. Create the dai_link to the mpc5200_psc_ac97 platform using the device tree. Convert the pcm030-audio-fabric driver to a platform-driver and add a remove function. Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: fsl: add PPC_MPC52xx dependency to SND_POWERPC_SOCEric Millbrandt
mpc52xx socs do not define FSL_SOC but need SND_POWERPC_SOC defined to build ASoC drivers. Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: twl6040: Convert to use DAI DAPM widgetsPeter Ujfalusi
Use DAPM mapping for stream events and give unique names for the streams. This change also fixes the following warning: twl6040-codec twl6040-codec: Failed to create Capture debugfs file Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-22ASoC: twl4030: Convert to use DAI DAPM widgetsPeter Ujfalusi
Use DAPM mapping for stream events and give unique names for the streams. This change also fixes the following warning: twl4030-codec twl4030-codec: Failed to create Capture debugfs file Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-21ASoC: wm8960: remove 'dres' field from platform data structureTimur Tabi
The 'dres' field (discharge resistance for headphone outputs) is no longer used in the driver, so remove it. It was used in the original version of the driver when entering standby from off, but we stopped using it when we switched from having a single startup sequence to having separate cap and capless sequences. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-20ASoC: Ux500: Minor coding layout changesLee Jones
Includes removal of duplicate debug print affirming entry into the probe function, an unnecessary line break of a coding line <80 chars and a white space change (unintentional tab). Acked-by: Ola Lilja <ola.o.lilja@stericsson.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2012-09-20ASoC: codecs: Enable AB8500 CODEC for Device TreeLee Jones
We continue to allow the AB8500 CODEC to be registered via the AB8500 Multi Functional Device API, only this time we extract its configuration from the Device Tree binary. Acked-by: Ola Lilja <ola.o.lilja@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2012-09-20ASoC: Ux500: Enable ux500 MSP driver for Device TreeLee Jones
Register both parts of the MSP driver from Device Tree so that they are probed when Device Tree is enabled. Also, as there is platform data involved, we ensure that there is allocated memory to place the configuration into and that the correct information is extracted from the DT binary. Acked-by: Ola Lilja <ola.o.lilja@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2012-09-20ASoC: Ux500: Enable MOP500 driver for Device TreeLee Jones
Here we ensure that the MOP500 audio driver will be probed during a Device Tree boot. We also parse the sound node to link together the codec, dma and the CPU-side Digital Audio Interface. Acked-by: Ola Lilja <ola.o.lilja@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2012-09-20ASoC: Ux500: Move MSP pinctrl setup into the MSP driverLee Jones
In the initial submission of the MSP driver msp1 and msp3's associated pinctrl mechanism was passed back to platform code using a plat_init() call-back routine, but it has no place in platform code. The MSP driver should set this up for the appropriate ports. Instead we use a use_pinctrl identifier which is passed from platform_data/Device Tree which indicates which ports should use pinctrl. Acked-by: Ola Lilja <ola.o.lilja@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2012-09-18ASoC: wm8961: Move device identification and reset to I2C probeMark Brown
This is more idiomatic as it means we verify that the device is there prior to trying to do the card probe. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-18ASoC: wm8961: Convert to direct regmap API usageMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-18ASoC: wm8960: Support shared LRCLKMark Brown
If the LRCLK is shared and the WM8960 is clock master then we should enable the LRCM bit to tell the device that it should drive LRCLK when either ADC or DAC is enabled rather than separately driving the two LRCLKs. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-18ASoC: wm8776: Convert to direct regmap API usageMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-18ASoC: fsl: cleanup headers in pcm030-audio-fabricEric Millbrandt
Remove unreferenced header files. Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-18ASoC: fsl: mpc5200 add missing information to snd_soc_dai_driverEric Millbrandt
Add missing dai_driver information to avoid these runtime errors [ 16.433788] asoc: error - multiple DAI f0002c00.i2s registered with no name [ 16.453551] Failed to register DAI [ 16.461222] mpc5200-psc-i2s: probe of f0002c00.i2s failed with error -22 [ 16.475242] asoc: error - multiple DAI f0002000.ac97 registered with no name [ 16.488087] mpc5200-psc-ac97 f0002000.ac97: Failed to register DAI [ 16.502222] mpc5200-psc-ac97: probe of f0002000.ac97 failed with error -22 Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-18ASoC: fsl: mpc5200 combine psc_dma platform dataEric Millbrandt
The mpc5200_psc_ac97 and mpc5200_psc_i2s modules rely on shared platform data with mpc5200_dma. Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-10-04 08:33:42 +0000