summaryrefslogtreecommitdiffstats
path: root/sound
AgeCommit message (Collapse)Author
2013-01-21ALSA: hda - Add aamix NID to IDT 92HD codecsTakashi Iwai
IDT codecs have analog-loopback mixer widgets, but we haven't cared about it, so far. Let's set them. This will avoid also possible wrong routes for the input paths. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-21ALSA: hda - Remove superfluous header inclusionsTakashi Iwai
Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-21ALSA: hda - Enable parsing the independent HP mode as default for VIA codecsTakashi Iwai
The original VIA codec parser enabled it as default, so let's keep the behavior as it was. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-21ALSA: hda - Fix conflicts between Loopback Mixing and Independent HPTakashi Iwai
This patch eventually fixes two issues: - Handle the case where the primary output is a headphone and can have independent HP mode; so far we checked only the case where the headphone is the secondary output. - Fix the conflict of HP independent mode and aamix mode; when switched to aamix mode, the DAC might be also switched to another widget shared with other outputs. Then even if we disable the DAC for the original output, it doesn't change -- because the active route is from another (shared) DAC to HP pin through aamix. So, in such a case, we have to prohibit the switch to aamix for HP routes. This fixes issues appearing on VT codecs. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-21ALSA: hda - Check aamix-output paths from other DACs, tooTakashi Iwai
Many codecs provide routes to multiple output pins through an aamix widget, but most of them do it only from a single DAC. However, the current generic parser checks only the aamix paths from the original (directly bound) DACs through aamix NID, and miss the path: primary DAC -> aamix -> target out pin This patch adds a more check for the routes like the above. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-21ALSA: hda - Add missing badness evaluation for unresolved pathsTakashi Iwai
When a patch couldn't be resolved in try_assign_dacs() although the target DAC is expected, we forgot to add a proper badness value but continued. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-21ALSA: hda - Set the pin targets after deciding output configTakashi Iwai
Since fill_and_eval_dacs() may be called repeatedly with different configurations, setting pinctls at each time there isn't optimal. We can set it better only once after deciding the output configuration in parse_output_paths(). Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-21ALSA: hda - Improve debug prints for output pathsTakashi Iwai
Print the information of outputs in a bit more details and concisely in a single place instead of printing the path at each time when detected. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-21ASoC: core: Ensure SND_SOC_BYTES writes are from DMA safe memoryMark Brown
With some buses the transfers may DMAed, especially for larger blocks. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-21ASoC: arizona: Allow number of channels clocked to be restrictedMark Brown
Place a cap on the number of channels clocks are generated for. This is intended for use with systems which have the WM5102 master an I2S bus with multiple data lines. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-21ASoC: wm_adsp: Provide explicit trace of coefficient writesMark Brown
Helpful for debugging. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-21Merge remote-tracking branch 'asoc/fix/adsp' into asoc-adspMark Brown
2013-01-21ASoC: arizona: Support clearing clocksMark Brown
Some systems may wish to support switching between telephony and CD audio clock rates but this is restricted by enforcement of constraints on the current DAI clock. Support setting clocks to zero and don't enforce any constraints in that case in order to facilitate this use case. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-21taint: add explicit flag to show whether lock dep is still OK.Rusty Russell
Fix up all callers as they were before, with make one change: an unsigned module taints the kernel, but doesn't turn off lockdep. Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2013-01-20ASoC: wm_adsp: Use GFP_DMA for algorithm readbackMark Brown
Normally kmalloc() returns things that are DMA safe so not visible on all platforms but we do need to explicitly request DMA safe memory. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-20ASoC: wm_adsp: Use GFP_DMA for things that may be DMAedMark Brown
Normally kmalloc() returns things that are DMA safe so not visible on all platforms but we do need to explicitly request DMA safe memory. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-20ASoC: wm_adsp: Make region identification errors more informativeMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-20ASoC: wm2200: Implement EQ and LHPF coefficient configurationMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-20ASoC: wm5100: Implement DRC, EQ and LHPF coefficient configurationMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-19ALSA: hda - Add fixup for Acer AO725 laptopTakashi Iwai
Acer AO725 needs the same fixup as AO756. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52181 Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18tty: Added a CONFIG_TTY option to allow removal of TTYJoe Millenbach
The option allows you to remove TTY and compile without errors. This saves space on systems that won't support TTY interfaces anyway. bloat-o-meter output is below. The bulk of this patch consists of Kconfig changes adding "depends on TTY" to various serial devices and similar drivers that require the TTY layer. Ideally, these dependencies would occur on a common intermediate symbol such as SERIO, but most drivers "select SERIO" rather than "depends on SERIO", and "select" does not respect dependencies. bloat-o-meter output comparing our previous minimal to new minimal by removing TTY. The list is filtered to not show removed entries with awk '$3 != "-"' as the list was very long. add/remove: 0/226 grow/shrink: 2/14 up/down: 6/-35356 (-35350) function old new delta chr_dev_init 166 170 +4 allow_signal 80 82 +2 static.__warned 143 142 -1 disallow_signal 63 62 -1 __set_special_pids 95 94 -1 unregister_console 126 121 -5 start_kernel 546 541 -5 register_console 593 588 -5 copy_from_user 45 40 -5 sys_setsid 128 120 -8 sys_vhangup 32 19 -13 do_exit 1543 1526 -17 bitmap_zero 60 40 -20 arch_local_irq_save 137 117 -20 release_task 674 652 -22 static.spin_unlock_irqrestore 308 260 -48 Signed-off-by: Joe Millenbach <jmillenbach@gmail.com> Reviewed-by: Jamey Sharp <jamey@minilop.net> Reviewed-by: Josh Triplett <josh@joshtriplett.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-01-18ALSA: hda/conexant - Set mixer NID 0x19 for CX20551 codecTakashi Iwai
Conexant CX20551 codec has a mixer in NID 0x19 and a few outputs have to take the input through this widget. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - Correct more array rooms in hda_gen_specTakashi Iwai
Looking through the whole definitions, some fields have inappropriate array sizes, especially about the capture. The array assigned to each input (pin) should have HDA_MAX_NUM_INPUTS entries while the array assigned to each ADC should have AUTO_CFG_MAX_INS entries. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - Fix the wrong adc_idx for capture sourceTakashi Iwai
The patch "ALSA: hda - fix wrong adc_idx in generic parser" fixed the adc_idx for the capture volume and capture switch controls. But also modified the adc_idx retrieval for the capture source controls wrongly. As multiple capture source controls are created in a single shot with counts > 1, the id.index doesn't contain the real value. The real index has to be taken via snd_ctl_get_ioffidx() as in the original code. This patch reverts the fixes partially to recover from the regression. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - Don't add unnecessary indices on HDMI and SPDIFDavid Henningsson
If there's one each of HDMI and SPDIF, we should not add an index on the one that comes second. [slight code refactoring by tiwai] Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - don't compare with yourself in fill_input_pin_labelsDavid Henningsson
Just stumbled over this one while reading the code. Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - make sure there are enough input labels and pathsDavid Henningsson
I found a codec configuration which had six inputs, so the max of five was not appropriate. Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - Fix speaker pin of FSC Lifebook S7110 laptopTakashi Iwai
Some BIOS version of FSC Lifebook S7110 laptop seems to give a wrong default pin config for NID 0x15, which confuses the parser. Give a fixup to correct the value. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - Add boost to line inputs, tooTakashi Iwai
Although I commented that boost volumes would be added only for line-in and mic pins in the source code, the actual code excludes but for mic-in. Fix it to accept the line-ins, too. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda/sigmatel - Add bass speaker support for HP ENVY Spectre XTTakashi Iwai
The pin configuration for the bass speaker needs to be corrected in a fixup. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - Consolidate cap_sync_hook and capture_switch_hookTakashi Iwai
Two hooks in hda_gen_spec, cap_sync_hook and capture_switch_hook, play very similar roles. The only differences are that the former is called more often (e.g. at init or switching capsrc) while the latter can take an on/off argument. As a more generic implementation, consolidate these two hooks, and pass snd_ctl_elem_value pointer as the second argument. If the secondary argument is non-NULL, it can take the on/off value, so the caller handles it like the former capture_switch_hook. If it's NULL, it's called in the init or capsrc switch case. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - Fix missing call of capture_switch_hookTakashi Iwai
When a standard capture switch without multiple binding is used, the call for capture_switch_hook isn't called properly. Replace the put ops to add the hook call in that case. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - Fix mute led for another HP machineDavid Henningsson
This machine also has the "HP_Mute_LED_0_A" string in DMI information. Cc: <stable@vger.kernel.org> BugLink: https://bugs.launchpad.net/bugs/1096789 Tested-by: Tammy Yang <tammy.yang@canonical.com> Signed-off-by: David Henningsson <david.henningsson@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - Look for boost controls more deeplyTakashi Iwai
In the current generic parser code, we look for the (mic) boost controls only on input pins. But many codecs assign the boost volume to a widget connected to each input pin instead of the input amp of the pin itself. In this patch, the parser tries to look through more widgets connected to the pin and find a boost amp. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - Fix invalid mute in path activationTakashi Iwai
When an amp in the activation path is associated with mixer controls, activate_amp() tries to skip the initialization. It's good, but only if the mixer really initializes both mute and volume. Otherwise, either the mute of the volume is left uninitialized. This patch adds this missing check and properly initialize the partially controlled amps in an activation path. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - Unify input label creations in generic parserTakashi Iwai
There are a few places creating the labels and indices of kctls for each input pin in the current generic parser code. This is redundant and makes harder to maintain. Let's create the labels and indices at once and keep them in hda_gen_spec. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ALSA: hda - Keep autocfg.input idx value in imux tableTakashi Iwai
Since the imux table entries can be a subset of autocfg.input table, the indices of these aren't always same. For passing the proper index value of autocfg.input at creating input ctl labels (via snd_hda_autocfg_input_label()), keep the corresponding autocfg.input idx value in the index field of each imux item, which isn't used in the generic driver. Also, this makes easier to check the invalid imux pin for stereo mix. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18Merge remote-tracking branch 'asoc/topic/adsp' into asoc-wm2200Mark Brown
2013-01-18ASoC: wm_adsp: Set ADSP1 clock rate to match sys clockChris Rattray
Sets the ADSP1 clock rate to match the system clock rate. To support this the codec driver provides details of register containing the system clock control bits. Signed-off-by: Chris Rattray <crattray@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-18ALSA: hda - Fix missing unsol event handler in some codec driversTakashi Iwai
This resulted in non-working auto-mute behavior, of course... Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-18ASoC: wm5102: Add controls for firmware selectionMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-18ASoC: wm2200: Add controls for firmware enumerationMark Brown
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-18ASoC: wm_adsp: Implement support for coefficeint file format 1Mark Brown
Implement support for a new revision of the coefficeint file format for ADSP cores. Since coefficient file format 0 has not been widely deployed and is very unlikely to ever be used with this driver code support for it has been removed. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2013-01-17ALSA: hda - Use generic parser for STAC/IDT codec driverTakashi Iwai
Finally we reached here. All codecs driver (except for CA0132, which has really device-specific requirements) have been converted to use the generic parser. This patch appears bigger than others since it also involves with the code shuffling, but mostly the cut-off of parser codes and adapt to the generic parser flags. Most of fixup codecs haven't been changed but just removed a few unnecessary codes. The only missing stuff is the SPDIF mux control. It'll be added again later. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-17Merge branch 'test/hda-gen-parser' into test/hda-migrateTakashi Iwai
* test/hda-gen-parser: ALSA: hda - Improve naming rule for primary output ALSA: hda - Add PCM capture hook to hda_gen_spec ALSA: hda - Record all detected ADCs in hda_gen_spec ALSA: hda - Move vmaster TLV parsing to snd_hda_gen_parse_auto_config() ALSA: hda - Add input jack mode enum controls to generic parser ALSA: hda - Give more comments to hda_gen_spec flags ALSA: hda - Add suppress_auto_mute flag to hda_gen_spec ALSA: hda - Record the current speaker / LO mute status in hda_gen_spec ALSA: hda - Properly call automute/switch hooks at init
2013-01-17ALSA: hda - Improve naming rule for primary outputTakashi Iwai
When the volume or mute control of the primary output is shared with other (headphone or speaker) outputs, we shouldn't name it as a specific output type but rather name it with the channel name or a generic name like "PCM". Also, this check should be performed individually for the volume and the mute controls because some codecs may have shared volumes but separate mute controls. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-17ALSA: hda - Add PCM capture hook to hda_gen_specTakashi Iwai
Not only PCM playback, a hook for PCM capture would be required for power controls in codec drivers. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-17ALSA: hda - Record all detected ADCs in hda_gen_specTakashi Iwai
Since the generic parser reduces the ADC list, copy the list of the all detected ADCs and keep it. This list can be later referred by the codec driver for finer power controls. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-17ALSA: hda - Move vmaster TLV parsing to snd_hda_gen_parse_auto_config()Takashi Iwai
Add vmaster_tlv[] to hda_gen_spec and store the suggested TLV data in snd_hda_gen_parse_auto_config(). This allows the codec driver to correct the TLV data (e.g. mute capability) before actually creating vmaster instance. Signed-off-by: Takashi Iwai <tiwai@suse.de>
2013-01-17ALSA: hda - Add input jack mode enum controls to generic parserTakashi Iwai
Just like the jack mode enum ctls for output jacks, add the support for similar enum ctls for input pins to control the bias Vref. The new controls will be added when spec->add_in_jack_modes is set either by the codec driver or by a hint string. Note that ground and 100% vrefs are excluded from the list for simplicity, currently. We may add a new flag to allow them, too. But I guess it's easier to put a value override in the pinfix in such a case. Signed-off-by: Takashi Iwai <tiwai@suse.de>