From 05745c4ab1c58fbb6ab8e8d3a40e0e395d7e2b0e Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Wed, 19 Sep 2007 15:36:45 -0700 Subject: sky2: fe+ chip support Add support for newest Marvell chips. The Yukon FE plus chip is found in some not yet released laptops. Tested on hardware evaluation boards. This version of the patch is for 2.6.23. It supersedes the two previous patches that are sitting in netdev-2.6 (upstream branch). Signed-off-by: Stephen Hemminger Signed-off-by: Jeff Garzik --- drivers/net/sky2.c | 136 ++++++++++++++++++++++++++++++++++++++++------------- drivers/net/sky2.h | 18 +++++-- 2 files changed, 117 insertions(+), 37 deletions(-) diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 060951a8022..d0e5875628e 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -118,12 +118,15 @@ static const struct pci_device_id sky2_id_table[] = { { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4351) }, /* 88E8036 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4352) }, /* 88E8038 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4353) }, /* 88E8039 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4354) }, /* 88E8040 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4356) }, /* 88EC033 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x435A) }, /* 88E8048 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4360) }, /* 88E8052 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4361) }, /* 88E8050 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4362) }, /* 88E8053 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4363) }, /* 88E8055 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4364) }, /* 88E8056 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4365) }, /* 88E8070 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4366) }, /* 88EC036 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4367) }, /* 88EC032 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4368) }, /* 88EC034 */ @@ -147,6 +150,7 @@ static const char *yukon2_name[] = { "Extreme", /* 0xb5 */ "EC", /* 0xb6 */ "FE", /* 0xb7 */ + "FE+", /* 0xb8 */ }; static void sky2_set_multicast(struct net_device *dev); @@ -331,7 +335,7 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); if (sky2_is_copper(hw)) { - if (hw->chip_id == CHIP_ID_YUKON_FE) { + if (!(hw->flags & SKY2_HW_GIGABIT)) { /* enable automatic crossover */ ctrl |= PHY_M_PC_MDI_XMODE(PHY_M_PC_ENA_AUTO) >> 1; } else { @@ -450,7 +454,7 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) gma_write16(hw, port, GM_GP_CTRL, reg); - if (hw->chip_id != CHIP_ID_YUKON_FE) + if (hw->flags & SKY2_HW_GIGABIT) gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000); gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv); @@ -474,6 +478,23 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl); break; + case CHIP_ID_YUKON_FE_P: + /* Enable Link Partner Next Page */ + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + ctrl |= PHY_M_PC_ENA_LIP_NP; + + /* disable Energy Detect and enable scrambler */ + ctrl &= ~(PHY_M_PC_ENA_ENE_DT | PHY_M_PC_DIS_SCRAMB); + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + /* set LED2 -> ACT, LED1 -> LINK, LED0 -> SPEED */ + ctrl = PHY_M_FELP_LED2_CTRL(LED_PAR_CTRL_ACT_BL) | + PHY_M_FELP_LED1_CTRL(LED_PAR_CTRL_LINK) | + PHY_M_FELP_LED0_CTRL(LED_PAR_CTRL_SPEED); + + gm_phy_write(hw, port, PHY_MARV_FE_LED_PAR, ctrl); + break; + case CHIP_ID_YUKON_XL: pg = gm_phy_read(hw, port, PHY_MARV_EXT_ADR); @@ -543,7 +564,13 @@ static void sky2_phy_init(struct sky2_hw *hw, unsigned port) /* set page register to 0 */ gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0); + } else if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) { + /* apply workaround for integrated resistors calibration */ + gm_phy_write(hw, port, PHY_MARV_PAGE_ADDR, 17); + gm_phy_write(hw, port, PHY_MARV_PAGE_DATA, 0x3f60); } else if (hw->chip_id != CHIP_ID_YUKON_EX) { + /* no effect on Yukon-XL */ gm_phy_write(hw, port, PHY_MARV_LED_CTRL, ledctrl); if (sky2->autoneg == AUTONEG_DISABLE || sky2->speed == SPEED_100) { @@ -664,25 +691,25 @@ static void sky2_wol_init(struct sky2_port *sky2) static void sky2_set_tx_stfwd(struct sky2_hw *hw, unsigned port) { - if (hw->chip_id == CHIP_ID_YUKON_EX && hw->chip_rev != CHIP_REV_YU_EX_A0) { + struct net_device *dev = hw->dev[port]; + + if (dev->mtu <= ETH_DATA_LEN) sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), - TX_STFW_ENA | - (hw->dev[port]->mtu > ETH_DATA_LEN) ? TX_JUMBO_ENA : TX_JUMBO_DIS); - } else { - if (hw->dev[port]->mtu > ETH_DATA_LEN) { - /* set Tx GMAC FIFO Almost Empty Threshold */ - sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR), - (ECU_JUMBO_WM << 16) | ECU_AE_THR); + TX_JUMBO_DIS | TX_STFW_ENA); + + else if (hw->chip_id != CHIP_ID_YUKON_EC_U) + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), + TX_STFW_ENA | TX_JUMBO_ENA); + else { + /* set Tx GMAC FIFO Almost Empty Threshold */ + sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR), + (ECU_JUMBO_WM << 16) | ECU_AE_THR); - sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), - TX_JUMBO_ENA | TX_STFW_DIS); + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), + TX_JUMBO_ENA | TX_STFW_DIS); - /* Can't do offload because of lack of store/forward */ - hw->dev[port]->features &= ~(NETIF_F_TSO | NETIF_F_SG - | NETIF_F_ALL_CSUM); - } else - sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), - TX_JUMBO_DIS | TX_STFW_ENA); + /* Can't do offload because of lack of store/forward */ + dev->features &= ~(NETIF_F_TSO | NETIF_F_SG | NETIF_F_ALL_CSUM); } } @@ -768,7 +795,8 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port) /* Configure Rx MAC FIFO */ sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR); rx_reg = GMF_OPER_ON | GMF_RX_F_FL_ON; - if (hw->chip_id == CHIP_ID_YUKON_EX) + if (hw->chip_id == CHIP_ID_YUKON_EX || + hw->chip_id == CHIP_ID_YUKON_FE_P) rx_reg |= GMF_RX_OVER_ON; sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), rx_reg); @@ -777,7 +805,12 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port) sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), GMR_FS_ANY_ERR); /* Set threshold to 0xa (64 bytes) + 1 to workaround pause bug */ - sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF+1); + reg = RX_GMF_FL_THR_DEF + 1; + /* Another magic mystery workaround from sk98lin */ + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) + reg = 0x178; + sky2_write16(hw, SK_REG(port, RX_GMF_FL_THR), reg); /* Configure Tx MAC FIFO */ sky2_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR); @@ -1704,8 +1737,12 @@ static u16 sky2_phy_speed(const struct sky2_hw *hw, u16 aux) if (hw->flags & SKY2_HW_FIBRE_PHY) return SPEED_1000; - if (hw->chip_id == CHIP_ID_YUKON_FE) - return (aux & PHY_M_PS_SPEED_100) ? SPEED_100 : SPEED_10; + if (!(hw->flags & SKY2_HW_GIGABIT)) { + if (aux & PHY_M_PS_SPEED_100) + return SPEED_100; + else + return SPEED_10; + } switch (aux & PHY_M_PS_SPEED_MSK) { case PHY_M_PS_SPEED_1000: @@ -1949,7 +1986,9 @@ static int sky2_change_mtu(struct net_device *dev, int new_mtu) if (new_mtu < ETH_ZLEN || new_mtu > ETH_JUMBO_MTU) return -EINVAL; - if (new_mtu > ETH_DATA_LEN && hw->chip_id == CHIP_ID_YUKON_FE) + if (new_mtu > ETH_DATA_LEN && + (hw->chip_id == CHIP_ID_YUKON_FE || + hw->chip_id == CHIP_ID_YUKON_FE_P)) return -EINVAL; if (!netif_running(dev)) { @@ -1966,7 +2005,7 @@ static int sky2_change_mtu(struct net_device *dev, int new_mtu) synchronize_irq(hw->pdev->irq); - if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) + if (!(hw->flags & SKY2_HW_RAMBUFFER)) sky2_set_tx_stfwd(hw, port); ctl = gma_read16(hw, port, GM_GP_CTRL); @@ -2205,7 +2244,7 @@ static int sky2_status_intr(struct sky2_hw *hw, int to_do) } /* This chip reports checksum status differently */ - if (hw->chip_id == CHIP_ID_YUKON_EX) { + if (hw->flags & SKY2_HW_NEW_LE) { if (sky2->rx_csum && (le->css & (CSS_ISIPV4 | CSS_ISIPV6)) && (le->css & CSS_TCPUDPCSOK)) @@ -2246,8 +2285,14 @@ static int sky2_status_intr(struct sky2_hw *hw, int to_do) if (!sky2->rx_csum) break; - if (hw->chip_id == CHIP_ID_YUKON_EX) + /* If this happens then driver assuming wrong format */ + if (unlikely(hw->flags & SKY2_HW_NEW_LE)) { + if (net_ratelimit()) + printk(KERN_NOTICE "%s: unexpected" + " checksum status\n", + dev->name); break; + } /* Both checksum counters are programmed to start at * the same offset, so unless there is a problem they @@ -2549,17 +2594,25 @@ static void sky2_netpoll(struct net_device *dev) #endif /* Chip internal frequency for clock calculations */ -static inline u32 sky2_mhz(const struct sky2_hw *hw) +static u32 sky2_mhz(const struct sky2_hw *hw) { switch (hw->chip_id) { case CHIP_ID_YUKON_EC: case CHIP_ID_YUKON_EC_U: case CHIP_ID_YUKON_EX: - return 125; /* 125 Mhz */ + return 125; + case CHIP_ID_YUKON_FE: - return 100; /* 100 Mhz */ - default: /* YUKON_XL */ - return 156; /* 156 Mhz */ + return 100; + + case CHIP_ID_YUKON_FE_P: + return 50; + + case CHIP_ID_YUKON_XL: + return 156; + + default: + BUG(); } } @@ -2623,6 +2676,12 @@ static int __devinit sky2_init(struct sky2_hw *hw) hw->flags = SKY2_HW_RAMBUFFER; break; + case CHIP_ID_YUKON_FE_P: + hw->flags = SKY2_HW_NEWER_PHY + | SKY2_HW_NEW_LE + | SKY2_HW_AUTO_TX_SUM + | SKY2_HW_ADV_POWER_CTL; + break; default: dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n", hw->chip_id); @@ -2827,7 +2886,9 @@ static int sky2_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol) sky2->wol = wol->wolopts; - if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) + if (hw->chip_id == CHIP_ID_YUKON_EC_U || + hw->chip_id == CHIP_ID_YUKON_EX || + hw->chip_id == CHIP_ID_YUKON_FE_P) sky2_write32(hw, B0_CTST, sky2->wol ? Y2_HW_WOL_ON : Y2_HW_WOL_OFF); @@ -3820,6 +3881,13 @@ static __devinit struct net_device *sky2_init_netdev(struct sky2_hw *hw, sky2->hw = hw; sky2->msg_enable = netif_msg_init(debug, default_msg); + /* This chip has hardware problems that generates + * bogus PHY receive status so by default shut up the message. + */ + if (hw->chip_id == CHIP_ID_YUKON_FE_P && + hw->chip_rev == CHIP_REV_YU_FE2_A0) + sky2->msg_enable &= ~NETIF_MSG_RX_ERR; + /* Auto speed and flow control */ sky2->autoneg = AUTONEG_ENABLE; sky2->flow_mode = FC_BOTH; @@ -4189,7 +4257,9 @@ static int sky2_resume(struct pci_dev *pdev) pci_enable_wake(pdev, PCI_D0, 0); /* Re-enable all clocks */ - if (hw->chip_id == CHIP_ID_YUKON_EX || hw->chip_id == CHIP_ID_YUKON_EC_U) + if (hw->chip_id == CHIP_ID_YUKON_EX || + hw->chip_id == CHIP_ID_YUKON_EC_U || + hw->chip_id == CHIP_ID_YUKON_FE_P) sky2_pci_write32(hw, PCI_DEV_REG3, 0); sky2_reset(hw); diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index af303496f9e..a05b30b68fa 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -470,18 +470,24 @@ enum { CHIP_ID_YUKON_EX = 0xb5, /* Chip ID for YUKON-2 Extreme */ CHIP_ID_YUKON_EC = 0xb6, /* Chip ID for YUKON-2 EC */ CHIP_ID_YUKON_FE = 0xb7, /* Chip ID for YUKON-2 FE */ - + CHIP_ID_YUKON_FE_P = 0xb8, /* Chip ID for YUKON-2 FE+ */ +}; +enum yukon_ec_rev { CHIP_REV_YU_EC_A1 = 0, /* Chip Rev. for Yukon-EC A1/A0 */ CHIP_REV_YU_EC_A2 = 1, /* Chip Rev. for Yukon-EC A2 */ CHIP_REV_YU_EC_A3 = 2, /* Chip Rev. for Yukon-EC A3 */ - +}; +enum yukon_ec_u_rev { CHIP_REV_YU_EC_U_A0 = 1, CHIP_REV_YU_EC_U_A1 = 2, CHIP_REV_YU_EC_U_B0 = 3, - +}; +enum yukon_fe_rev { CHIP_REV_YU_FE_A1 = 1, CHIP_REV_YU_FE_A2 = 2, - +}; +enum yukon_fe_p_rev { + CHIP_REV_YU_FE2_A0 = 0, }; enum yukon_ex_rev { CHIP_REV_YU_EX_A0 = 1, @@ -1729,6 +1735,10 @@ enum { GMF_RX_CTRL_DEF = GMF_OPER_ON | GMF_RX_F_FL_ON, }; +/* TX_GMF_EA 32 bit Tx GMAC FIFO End Address */ +enum { + TX_DYN_WM_ENA = 3, /* Yukon-FE+ specific */ +}; /* TX_GMF_CTRL_T 32 bit Tx GMAC FIFO Control/Test */ enum { -- cgit v1.2.3-70-g09d2