From 2909c3f79d933b55bf2485addb1dca762210b6af Mon Sep 17 00:00:00 2001 From: Alexander Duyck Date: Thu, 19 Nov 2009 12:41:42 +0000 Subject: igb: add support for the 82580 phy This patch adds support for the phy included in the 82580 silicon family. Signed-off-by: Alexander Duyck Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/igb/e1000_hw.h | 1 + drivers/net/igb/e1000_phy.c | 242 ++++++++++++++++++++++++++++++++++++++++++++ drivers/net/igb/e1000_phy.h | 32 ++++++ 3 files changed, 275 insertions(+) diff --git a/drivers/net/igb/e1000_hw.h b/drivers/net/igb/e1000_hw.h index 2dc929419df..5deda3e7842 100644 --- a/drivers/net/igb/e1000_hw.h +++ b/drivers/net/igb/e1000_hw.h @@ -93,6 +93,7 @@ enum e1000_phy_type { e1000_phy_gg82563, e1000_phy_igp_3, e1000_phy_ife, + e1000_phy_82580, }; enum e1000_bus_type { diff --git a/drivers/net/igb/e1000_phy.c b/drivers/net/igb/e1000_phy.c index 83b706c460b..b8fbc8558fe 100644 --- a/drivers/net/igb/e1000_phy.c +++ b/drivers/net/igb/e1000_phy.c @@ -420,6 +420,57 @@ out: return ret_val; } +/** + * igb_copper_link_setup_82580 - Setup 82580 PHY for copper link + * @hw: pointer to the HW structure + * + * Sets up Carrier-sense on Transmit and downshift values. + **/ +s32 igb_copper_link_setup_82580(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + + + if (phy->reset_disable) { + ret_val = 0; + goto out; + } + + if (phy->type == e1000_phy_82580) { + ret_val = hw->phy.ops.reset(hw); + if (ret_val) { + hw_dbg("Error resetting the PHY.\n"); + goto out; + } + } + + /* Enable CRS on TX. This must be set for half-duplex operation. */ + ret_val = phy->ops.read_reg(hw, I82580_CFG_REG, &phy_data); + if (ret_val) + goto out; + + phy_data |= I82580_CFG_ASSERT_CRS_ON_TX; + + /* Enable downshift */ + phy_data |= I82580_CFG_ENABLE_DOWNSHIFT; + + ret_val = phy->ops.write_reg(hw, I82580_CFG_REG, phy_data); + if (ret_val) + goto out; + + /* Set number of link attempts before downshift */ + ret_val = phy->ops.read_reg(hw, I82580_CTRL_REG, &phy_data); + if (ret_val) + goto out; + phy_data &= ~I82580_CTRL_DOWNSHIFT_MASK; + ret_val = phy->ops.write_reg(hw, I82580_CTRL_REG, phy_data); + +out: + return ret_val; +} + /** * igb_copper_link_setup_m88 - Setup m88 PHY's for copper link * @hw: pointer to the HW structure @@ -1888,3 +1939,194 @@ s32 igb_phy_init_script_igp3(struct e1000_hw *hw) return 0; } +/** + * igb_check_polarity_82580 - Checks the polarity. + * @hw: pointer to the HW structure + * + * Success returns 0, Failure returns -E1000_ERR_PHY (-2) + * + * Polarity is determined based on the PHY specific status register. + **/ +s32 igb_check_polarity_82580(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + + + ret_val = phy->ops.read_reg(hw, I82580_PHY_STATUS_2, &data); + + if (!ret_val) + phy->cable_polarity = (data & I82580_PHY_STATUS2_REV_POLARITY) + ? e1000_rev_polarity_reversed + : e1000_rev_polarity_normal; + + return ret_val; +} + +/** + * igb_phy_force_speed_duplex_82580 - Force speed/duplex for I82580 PHY + * @hw: pointer to the HW structure + * + * Calls the PHY setup function to force speed and duplex. Clears the + * auto-crossover to force MDI manually. Waits for link and returns + * successful if link up is successful, else -E1000_ERR_PHY (-2). + **/ +s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data; + bool link; + + + ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_data); + if (ret_val) + goto out; + + igb_phy_force_speed_duplex_setup(hw, &phy_data); + + ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_data); + if (ret_val) + goto out; + + /* + * Clear Auto-Crossover to force MDI manually. 82580 requires MDI + * forced whenever speed and duplex are forced. + */ + ret_val = phy->ops.read_reg(hw, I82580_PHY_CTRL_2, &phy_data); + if (ret_val) + goto out; + + phy_data &= ~I82580_PHY_CTRL2_AUTO_MDIX; + phy_data &= ~I82580_PHY_CTRL2_FORCE_MDI_MDIX; + + ret_val = phy->ops.write_reg(hw, I82580_PHY_CTRL_2, phy_data); + if (ret_val) + goto out; + + hw_dbg("I82580_PHY_CTRL_2: %X\n", phy_data); + + udelay(1); + + if (phy->autoneg_wait_to_complete) { + hw_dbg("Waiting for forced speed/duplex link on 82580 phy\n"); + + ret_val = igb_phy_has_link(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + goto out; + + if (!link) + hw_dbg("Link taking longer than expected.\n"); + + /* Try once more */ + ret_val = igb_phy_has_link(hw, + PHY_FORCE_LIMIT, + 100000, + &link); + if (ret_val) + goto out; + } + +out: + return ret_val; +} + +/** + * igb_get_phy_info_82580 - Retrieve I82580 PHY information + * @hw: pointer to the HW structure + * + * Read PHY status to determine if link is up. If link is up, then + * set/determine 10base-T extended distance and polarity correction. Read + * PHY port status to determine MDI/MDIx and speed. Based on the speed, + * determine on the cable length, local and remote receiver. + **/ +s32 igb_get_phy_info_82580(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 data; + bool link; + + + ret_val = igb_phy_has_link(hw, 1, 0, &link); + if (ret_val) + goto out; + + if (!link) { + hw_dbg("Phy info is only valid if link is up\n"); + ret_val = -E1000_ERR_CONFIG; + goto out; + } + + phy->polarity_correction = true; + + ret_val = igb_check_polarity_82580(hw); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, I82580_PHY_STATUS_2, &data); + if (ret_val) + goto out; + + phy->is_mdix = (data & I82580_PHY_STATUS2_MDIX) ? true : false; + + if ((data & I82580_PHY_STATUS2_SPEED_MASK) == + I82580_PHY_STATUS2_SPEED_1000MBPS) { + ret_val = hw->phy.ops.get_cable_length(hw); + if (ret_val) + goto out; + + ret_val = phy->ops.read_reg(hw, PHY_1000T_STATUS, &data); + if (ret_val) + goto out; + + phy->local_rx = (data & SR_1000T_LOCAL_RX_STATUS) + ? e1000_1000t_rx_status_ok + : e1000_1000t_rx_status_not_ok; + + phy->remote_rx = (data & SR_1000T_REMOTE_RX_STATUS) + ? e1000_1000t_rx_status_ok + : e1000_1000t_rx_status_not_ok; + } else { + phy->cable_length = E1000_CABLE_LENGTH_UNDEFINED; + phy->local_rx = e1000_1000t_rx_status_undefined; + phy->remote_rx = e1000_1000t_rx_status_undefined; + } + +out: + return ret_val; +} + +/** + * igb_get_cable_length_82580 - Determine cable length for 82580 PHY + * @hw: pointer to the HW structure + * + * Reads the diagnostic status register and verifies result is valid before + * placing it in the phy_cable_length field. + **/ +s32 igb_get_cable_length_82580(struct e1000_hw *hw) +{ + struct e1000_phy_info *phy = &hw->phy; + s32 ret_val; + u16 phy_data, length; + + + ret_val = phy->ops.read_reg(hw, I82580_PHY_DIAG_STATUS, &phy_data); + if (ret_val) + goto out; + + length = (phy_data & I82580_DSTATUS_CABLE_LENGTH) >> + I82580_DSTATUS_CABLE_LENGTH_SHIFT; + + if (length == E1000_CABLE_LENGTH_UNDEFINED) + ret_val = -E1000_ERR_PHY; + + phy->cable_length = length; + +out: + return ret_val; +} diff --git a/drivers/net/igb/e1000_phy.h b/drivers/net/igb/e1000_phy.h index adb9436b733..e23b0211a20 100644 --- a/drivers/net/igb/e1000_phy.h +++ b/drivers/net/igb/e1000_phy.h @@ -63,6 +63,11 @@ s32 igb_phy_has_link(struct e1000_hw *hw, u32 iterations, s32 igb_phy_init_script_igp3(struct e1000_hw *hw); s32 igb_read_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 *data); s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data); +s32 igb_copper_link_setup_82580(struct e1000_hw *hw); +s32 igb_check_polarity_82580(struct e1000_hw *hw); +s32 igb_get_phy_info_82580(struct e1000_hw *hw); +s32 igb_phy_force_speed_duplex_82580(struct e1000_hw *hw); +s32 igb_get_cable_length_82580(struct e1000_hw *hw); /* IGP01E1000 Specific Registers */ #define IGP01E1000_PHY_PORT_CONFIG 0x10 /* Port Config */ @@ -77,6 +82,33 @@ s32 igb_write_phy_reg_i2c(struct e1000_hw *hw, u32 offset, u16 data); #define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0=MDI, 1=MDIX */ #define IGP01E1000_PSCFR_SMART_SPEED 0x0080 +#define I82580_ADDR_REG 16 +#define I82580_CFG_REG 22 +#define I82580_CFG_ASSERT_CRS_ON_TX (1 << 15) +#define I82580_CFG_ENABLE_DOWNSHIFT (3 << 10) /* auto downshift 100/10 */ +#define I82580_CTRL_REG 23 +#define I82580_CTRL_DOWNSHIFT_MASK (7 << 10) + +/* 82580 specific PHY registers */ +#define I82580_PHY_CTRL_2 18 +#define I82580_PHY_LBK_CTRL 19 +#define I82580_PHY_STATUS_2 26 +#define I82580_PHY_DIAG_STATUS 31 + +/* I82580 PHY Status 2 */ +#define I82580_PHY_STATUS2_REV_POLARITY 0x0400 +#define I82580_PHY_STATUS2_MDIX 0x0800 +#define I82580_PHY_STATUS2_SPEED_MASK 0x0300 +#define I82580_PHY_STATUS2_SPEED_1000MBPS 0x0200 +#define I82580_PHY_STATUS2_SPEED_100MBPS 0x0100 + +/* I82580 PHY Control 2 */ +#define I82580_PHY_CTRL2_AUTO_MDIX 0x0400 +#define I82580_PHY_CTRL2_FORCE_MDI_MDIX 0x0200 + +/* I82580 PHY Diagnostics Status */ +#define I82580_DSTATUS_CABLE_LENGTH 0x03FC +#define I82580_DSTATUS_CABLE_LENGTH_SHIFT 2 /* Enable flexible speed on link-up */ #define IGP02E1000_PM_D0_LPLU 0x0002 /* For D0a states */ #define IGP02E1000_PM_D3_LPLU 0x0004 /* For all other states */ -- cgit v1.2.3-70-g09d2