From 30b3710105be0ba6bbdb7d7d126af76246b02eba Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Fri, 4 Sep 2009 17:44:51 -0700 Subject: kmemleak: add clear command support In an ideal world your kmemleak output will be small, when its not (usually during initial bootup) you can use the clear command to ingore previously reported and unreferenced kmemleak objects. We do this by painting all currently reported unreferenced objects grey. We paint them grey instead of black to allow future scans on the same objects as such objects could still potentially reference newly allocated objects in the future. To test a critical section on demand with a clean /sys/kernel/debug/kmemleak you can do: echo clear > /sys/kernel/debug/kmemleak test your kernel or modules echo scan > /sys/kernel/debug/kmemleak Then as usual to get your report with: cat /sys/kernel/debug/kmemleak Signed-off-by: Luis R. Rodriguez Signed-off-by: Catalin Marinas --- Documentation/kmemleak.txt | 30 ++++++++++++++++++++++++++++++ mm/kmemleak.c | 26 ++++++++++++++++++++++++++ 2 files changed, 56 insertions(+) diff --git a/Documentation/kmemleak.txt b/Documentation/kmemleak.txt index c223785339b..34f6638aa5a 100644 --- a/Documentation/kmemleak.txt +++ b/Documentation/kmemleak.txt @@ -27,6 +27,13 @@ To trigger an intermediate memory scan: # echo scan > /sys/kernel/debug/kmemleak +To clear the list of all current possible memory leaks: + + # echo clear > /sys/kernel/debug/kmemleak + +New leaks will then come up upon reading /sys/kernel/debug/kmemleak +again. + Note that the orphan objects are listed in the order they were allocated and one object at the beginning of the list may cause other subsequent objects to be reported as orphan. @@ -42,6 +49,8 @@ Memory scanning parameters can be modified at run-time by writing to the scan= - set the automatic memory scanning period in seconds (default 600, 0 to stop the automatic scanning) scan - trigger a memory scan + clear - clear list of current memory leak suspects, done by + marking all current reported unreferenced objects grey dump= - dump information about the object found at Kmemleak can also be disabled at boot-time by passing "kmemleak=off" on @@ -87,6 +96,27 @@ avoid this, kmemleak can also store the number of values pointing to an address inside the block address range that need to be found so that the block is not considered a leak. One example is __vmalloc(). +Testing specific sections with kmemleak +--------------------------------------- + +Upon initial bootup your /sys/kernel/debug/kmemleak output page may be +quite extensive. This can also be the case if you have very buggy code +when doing development. To work around these situations you can use the +'clear' command to clear all reported unreferenced objects from the +/sys/kernel/debug/kmemleak output. By issuing a 'scan' after a 'clear' +you can find new unreferenced objects; this should help with testing +specific sections of code. + +To test a critical section on demand with a clean kmemleak do: + + # echo clear > /sys/kernel/debug/kmemleak + ... test your kernel or modules ... + # echo scan > /sys/kernel/debug/kmemleak + +Then as usual to get your report with: + + # cat /sys/kernel/debug/kmemleak + Kmemleak API ------------ diff --git a/mm/kmemleak.c b/mm/kmemleak.c index f5042b4a7b9..c17dbc76fb7 100644 --- a/mm/kmemleak.c +++ b/mm/kmemleak.c @@ -1420,6 +1420,28 @@ static int dump_str_object_info(const char *str) return 0; } +/* + * We use grey instead of black to ensure we can do future scans on the same + * objects. If we did not do future scans these black objects could + * potentially contain references to newly allocated objects in the future and + * we'd end up with false positives. + */ +static void kmemleak_clear(void) +{ + struct kmemleak_object *object; + unsigned long flags; + + rcu_read_lock(); + list_for_each_entry_rcu(object, &object_list, object_list) { + spin_lock_irqsave(&object->lock, flags); + if ((object->flags & OBJECT_REPORTED) && + unreferenced_object(object)) + object->min_count = 0; + spin_unlock_irqrestore(&object->lock, flags); + } + rcu_read_unlock(); +} + /* * File write operation to configure kmemleak at run-time. The following * commands can be written to the /sys/kernel/debug/kmemleak file: @@ -1431,6 +1453,8 @@ static int dump_str_object_info(const char *str) * scan=... - set the automatic memory scanning period in seconds (0 to * disable it) * scan - trigger a memory scan + * clear - mark all current reported unreferenced kmemleak objects as + * grey to ignore printing them * dump=... - dump information about the object found at the given address */ static ssize_t kmemleak_write(struct file *file, const char __user *user_buf, @@ -1472,6 +1496,8 @@ static ssize_t kmemleak_write(struct file *file, const char __user *user_buf, } } else if (strncmp(buf, "scan", 4) == 0) kmemleak_scan(); + else if (strncmp(buf, "clear", 5) == 0) + kmemleak_clear(); else if (strncmp(buf, "dump=", 5) == 0) ret = dump_str_object_info(buf + 5); else -- cgit v1.2.3-70-g09d2