From 3a71c05e66e597a1349fdbd5f0bb119d8d9cb850 Mon Sep 17 00:00:00 2001 From: Loic Poulain Date: Fri, 26 Sep 2014 16:14:51 +0200 Subject: pinctrl: baytrail: Clear DIRECT_IRQ bit Direct irq en bit should be cleared for pads using io mode. If not, the io based irq will never be detected. However, this bit can sometimes be misconfigured (BIOS issue). Force clearing of this bit in io mode and trigger a WARN. Signed-off-by: Loic Poulain Acked-by: Mika Westerberg Signed-off-by: Linus Walleij --- drivers/pinctrl/pinctrl-baytrail.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/drivers/pinctrl/pinctrl-baytrail.c b/drivers/pinctrl/pinctrl-baytrail.c index e12e5b07f6d..b83ec87c71f 100644 --- a/drivers/pinctrl/pinctrl-baytrail.c +++ b/drivers/pinctrl/pinctrl-baytrail.c @@ -227,10 +227,14 @@ static int byt_irq_type(struct irq_data *d, unsigned type) spin_lock_irqsave(&vg->lock, flags); value = readl(reg); + WARN(value & BYT_DIRECT_IRQ_EN, + "Bad pad config for io mode, force direct_irq_en bit clearing"); + /* For level trigges the BYT_TRIG_POS and BYT_TRIG_NEG bits * are used to indicate high and low level triggering */ - value &= ~(BYT_TRIG_POS | BYT_TRIG_NEG | BYT_TRIG_LVL); + value &= ~(BYT_DIRECT_IRQ_EN | BYT_TRIG_POS | BYT_TRIG_NEG | + BYT_TRIG_LVL); switch (type) { case IRQ_TYPE_LEVEL_HIGH: -- cgit v1.2.3-70-g09d2 From c11f042b8607f38410351fb30c224783f2b24fb7 Mon Sep 17 00:00:00 2001 From: David Cohen Date: Thu, 16 Oct 2014 19:06:59 -0700 Subject: pinctrl: use linux-gpio mailing list The GPIO concepts are close enough to pin control that we may use the same mailing list to discuss them. Signed-off-by: Linus Walleij --- MAINTAINERS | 1 + 1 file changed, 1 insertion(+) diff --git a/MAINTAINERS b/MAINTAINERS index a20df9bf8ab..d7df7913c61 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -7153,6 +7153,7 @@ F: drivers/crypto/picoxcell* PIN CONTROL SUBSYSTEM M: Linus Walleij +L: linux-gpio@vger.kernel.org S: Maintained F: drivers/pinctrl/ F: include/linux/pinctrl/ -- cgit v1.2.3-70-g09d2 From cde7fc879969f933614b1256df2625d6ff637bab Mon Sep 17 00:00:00 2001 From: Robert Jarzmik Date: Tue, 7 Oct 2014 21:18:14 +0200 Subject: ARM: pxa: fix hang on startup with DEBUG_LL The commit 2111667b4677 ("ARM: pxa: call debug_ll_io_init for earlyprintk") triggers in the current kernel the attached backtrace on PXA/tosa early in the boot time when DEBUG_LL is enabled. It is due to overlap between uart virtual memory defined in DEBUG_UART_VIRT and mapped by debug_ll_io_init() and peripheral bus mapped by pxa_map_io at the same address, 0xf2100000. As hinted by Arnd, map early virtual memory for low level debug on address 0xf6200000, even if that means 2 virtual mappings will give access to the pxa internal UARTs (FFUART, BTUART, STUART, ...). ------------[ cut here ]------------ kernel BUG at /home/lumag/linux/mm/vmalloc.c:1143! Internal error: Oops - BUG: 0 [#1] PREEMPT ARM Modules linked in: CPU: 0 PID: 0 Comm: swapper Not tainted 3.17.0-00032-g8e0d202-dirty #23 task: c062a5a8 ti: c0620000 task.ti: c0620000 PC is at vm_area_add_early+0x54/0x84 LR is at add_static_vm_early+0xc/0x60 pc : [] lr : [] psr: 800001d3 sp : c0621f04 ip : c03efa74 fp : c03edf84 r10: c0637e98 r9 : 40000001 r8 : c03da57c r7 : c3ffcfb0 r6 : 00000000 r5 : c3ffcfb0 r4 : 02000000 r3 : c3ffcfd8 r2 : f2100000 r1 : f4000000 r0 : c3ffcfb0 Flags: Nzcv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel Control: 00007977 Table: a0004000 DAC: 00000017 Process swapper (pid: 0, stack limit = 0xc06201c8) Stack: (0xc0621f04 to 0xc0622000) 1f00: c3ffcfd8 40000001 c3ffcfd8 c03ee08c c03da570 c03db90c c0637d24 1f20: 00000000 c03ec7cc c066e654 a0700000 000a0700 c03db914 c03db90c c03daf84 1f40: 00000000 000a0000 c0000000 c03ec7cc 000a0700 c0700000 ffff1000 000a3fff 1f60: 00001000 00000007 00000000 c03ec7cc c0008000 c03ed748 c0621fd4 c03d5d18 1f80: 69052d00 a03ec48c 00000000 c03d8ad0 0000006c 00007977 c036c6e8 00000001 1fa0: c0621fd4 c03ed744 c0628000 a0004000 69052d00 a03ec48c 00000000 c03d68d4 1fc0: 00000000 00000000 00000000 00000000 00000000 c03ed748 c0649894 c062801c 1fe0: c03ed744 c062b2f0 a0004000 69052d00 a03ec48c a0008040 00000000 00000000 [] (vm_area_add_early) from [] (add_static_vm_early+0xc/0x60) [] (add_static_vm_early) from [] (iotable_init.part.6+0xa8/0xb4) [] (iotable_init.part.6) from [] (pxa25x_map_io+0x8/0x24) [] (pxa25x_map_io) from [] (paging_init+0x744/0x8d8) [] (paging_init) from [] (setup_arch+0x354/0x608) [] (setup_arch) from [] (start_kernel+0xa8/0x3dc) [] (start_kernel) from [] (0xa0008040) Code: e5904008 e0811004 e1520001 2a000005 (e7f001f2) ---[ end trace f24b6c88ae00fa9a ]--- Kernel panic - not syncing: Attempted to kill the idle task! ---[ end Kernel panic - not syncing: Attempted to kill the idle task! Cc: Reported-by: Dmitry Eremin-Solenikov Signed-off-by: Robert Jarzmik Acked-by: Arnd Bergmann --- arch/arm/Kconfig.debug | 2 +- arch/arm/mach-pxa/include/mach/addr-map.h | 5 +++++ 2 files changed, 6 insertions(+), 1 deletion(-) diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug index 03dc4c1a873..d8f6a2ec3d4 100644 --- a/arch/arm/Kconfig.debug +++ b/arch/arm/Kconfig.debug @@ -1187,7 +1187,7 @@ config DEBUG_UART_VIRT default 0xf1c28000 if DEBUG_SUNXI_UART0 default 0xf1c28400 if DEBUG_SUNXI_UART1 default 0xf1f02800 if DEBUG_SUNXI_R_UART - default 0xf2100000 if DEBUG_PXA_UART1 + default 0xf6200000 if DEBUG_PXA_UART1 default 0xf4090000 if ARCH_LPC32XX default 0xf4200000 if ARCH_GEMINI default 0xf7000000 if DEBUG_S3C24XX_UART && (DEBUG_S3C_UART0 || \ diff --git a/arch/arm/mach-pxa/include/mach/addr-map.h b/arch/arm/mach-pxa/include/mach/addr-map.h index bbf9df37ad4..d28fe291233 100644 --- a/arch/arm/mach-pxa/include/mach/addr-map.h +++ b/arch/arm/mach-pxa/include/mach/addr-map.h @@ -38,6 +38,11 @@ #define DMEMC_VIRT IOMEM(0xf6100000) #define DMEMC_SIZE 0x00100000 +/* + * Reserved space for low level debug virtual addresses within + * 0xf6200000..0xf6201000 + */ + /* * Internal Memory Controller (PXA27x and later) */ -- cgit v1.2.3-70-g09d2 From 2ca6121c673e1a741f32b6d0857ae48be545d9db Mon Sep 17 00:00:00 2001 From: Dinh Nguyen Date: Tue, 21 Oct 2014 23:04:16 +0000 Subject: ARM: socfpga_defconfig: Update defconfig for SoCFPGA Clean up the socfpga_defconfig file by doing: make socfpga_defconfig make make savedefconfig Then add the following to socfpga_defconfig: CONFIG_SIGNALFD=y CONFIG_REGULATOR=y CONFIG_REGULATOR_FIXED_VOLTAGE=y CONFIG_SRAM=y CONFIG_DEVTMPFS_MOUNT=y CONFIG_CONFIGFS_FS=y CONFIG_PMBUS=y CONFIG_SENSORS_PMBUS=y CONFIG_SENSORS_LTC2978=y CONFIG_SENSORS_LTC2978_REGULATOR=y CONFIG_PRINTK_TIME=y CONFIG_EXT4_FS=y Signed-off-by: Thor Thayer Signed-off-by: Steffen Trumtrar Signed-off-by: Alan Tull Signed-off-by: Dinh Nguyen --- arch/arm/configs/socfpga_defconfig | 71 +++++++++++++++----------------------- 1 file changed, 28 insertions(+), 43 deletions(-) diff --git a/arch/arm/configs/socfpga_defconfig b/arch/arm/configs/socfpga_defconfig index d7a5855a5db..a2956c3112f 100644 --- a/arch/arm/configs/socfpga_defconfig +++ b/arch/arm/configs/socfpga_defconfig @@ -1,5 +1,6 @@ -CONFIG_EXPERIMENTAL=y CONFIG_SYSVIPC=y +CONFIG_FHANDLE=y +CONFIG_HIGH_RES_TIMERS=y CONFIG_IKCONFIG=y CONFIG_IKCONFIG_PROC=y CONFIG_LOG_BUF_SHIFT=14 @@ -11,23 +12,17 @@ CONFIG_PROFILING=y CONFIG_OPROFILE=y CONFIG_MODULES=y CONFIG_MODULE_UNLOAD=y -CONFIG_HOTPLUG=y # CONFIG_LBDAF is not set # CONFIG_BLK_DEV_BSG is not set # CONFIG_IOSCHED_DEADLINE is not set # CONFIG_IOSCHED_CFQ is not set CONFIG_ARCH_SOCFPGA=y -CONFIG_MACH_SOCFPGA_CYCLONE5=y CONFIG_ARM_THUMBEE=y -# CONFIG_ARCH_VEXPRESS_CORTEX_A5_A9_ERRATA is not set -# CONFIG_CACHE_L2X0 is not set -CONFIG_HIGH_RES_TIMERS=y CONFIG_SMP=y CONFIG_NR_CPUS=2 CONFIG_AEABI=y CONFIG_ZBOOT_ROM_TEXT=0x0 CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_CMDLINE="" CONFIG_VFP=y CONFIG_NEON=y CONFIG_NET=y @@ -41,38 +36,30 @@ CONFIG_IP_PNP=y CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y CONFIG_IP_PNP_RARP=y +CONFIG_IPV6=y +CONFIG_NETWORK_PHY_TIMESTAMPING=y +CONFIG_VLAN_8021Q=y +CONFIG_VLAN_8021Q_GVRP=y CONFIG_CAN=y -CONFIG_CAN_RAW=y -CONFIG_CAN_BCM=y -CONFIG_CAN_GW=y -CONFIG_CAN_DEV=y -CONFIG_CAN_CALC_BITTIMING=y CONFIG_CAN_C_CAN=y CONFIG_CAN_C_CAN_PLATFORM=y CONFIG_CAN_DEBUG_DEVICES=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" CONFIG_DEVTMPFS=y -CONFIG_PROC_DEVICETREE=y +CONFIG_DEVTMPFS_MOUNT=y CONFIG_BLK_DEV_RAM=y CONFIG_BLK_DEV_RAM_COUNT=2 CONFIG_BLK_DEV_RAM_SIZE=8192 +CONFIG_SRAM=y CONFIG_SCSI=y # CONFIG_SCSI_PROC_FS is not set CONFIG_BLK_DEV_SD=y # CONFIG_SCSI_LOWLEVEL is not set CONFIG_NETDEVICES=y CONFIG_STMMAC_ETH=y +CONFIG_DWMAC_SOCFPGA=y CONFIG_MICREL_PHY=y -# CONFIG_STMMAC_PHY_ID_ZERO_WORKAROUND is not set CONFIG_INPUT_EVDEV=y -CONFIG_DWMAC_SOCFPGA=y -CONFIG_PPS=y -CONFIG_NETWORK_PHY_TIMESTAMPING=y -CONFIG_PTP_1588_CLOCK=y -CONFIG_VLAN_8021Q=y -CONFIG_VLAN_8021Q_GVRP=y -CONFIG_GARP=y -CONFIG_IPV6=y # CONFIG_SERIO_SERPORT is not set CONFIG_SERIO_AMBAKMI=y CONFIG_LEGACY_PTY_COUNT=16 @@ -81,45 +68,43 @@ CONFIG_SERIAL_8250_CONSOLE=y CONFIG_SERIAL_8250_NR_UARTS=2 CONFIG_SERIAL_8250_RUNTIME_UARTS=2 CONFIG_SERIAL_8250_DW=y +CONFIG_I2C=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_DESIGNWARE_PLATFORM=y CONFIG_GPIOLIB=y CONFIG_GPIO_SYSFS=y CONFIG_GPIO_DWAPB=y -# CONFIG_RTC_HCTOSYS is not set +CONFIG_PMBUS=y +CONFIG_SENSORS_LTC2978=y +CONFIG_SENSORS_LTC2978_REGULATOR=y CONFIG_WATCHDOG=y CONFIG_DW_WATCHDOG=y +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +CONFIG_USB=y +CONFIG_USB_DWC2=y +CONFIG_USB_DWC2_HOST=y +CONFIG_MMC=y +CONFIG_MMC_DW=y CONFIG_EXT2_FS=y CONFIG_EXT2_FS_XATTR=y CONFIG_EXT2_FS_POSIX_ACL=y CONFIG_EXT3_FS=y -CONFIG_NFS_FS=y -CONFIG_ROOT_NFS=y -# CONFIG_DNOTIFY is not set -# CONFIG_INOTIFY_USER is not set -CONFIG_FHANDLE=y +CONFIG_EXT4_FS=y CONFIG_VFAT_FS=y CONFIG_NTFS_FS=y CONFIG_NTFS_RW=y CONFIG_TMPFS=y -CONFIG_JFFS2_FS=y +CONFIG_CONFIGFS_FS=y +CONFIG_NFS_FS=y +CONFIG_ROOT_NFS=y CONFIG_NLS_CODEPAGE_437=y CONFIG_NLS_ISO8859_1=y +CONFIG_PRINTK_TIME=y +CONFIG_DEBUG_INFO=y CONFIG_MAGIC_SYSRQ=y CONFIG_DETECT_HUNG_TASK=y # CONFIG_SCHED_DEBUG is not set -CONFIG_DEBUG_INFO=y CONFIG_ENABLE_DEFAULT_TRACERS=y CONFIG_DEBUG_USER=y CONFIG_XZ_DEC=y -CONFIG_I2C=y -CONFIG_I2C_DESIGNWARE_CORE=y -CONFIG_I2C_DESIGNWARE_PLATFORM=y -CONFIG_I2C_CHARDEV=y -CONFIG_MMC=y -CONFIG_MMC_DW=y -CONFIG_PM=y -CONFIG_SUSPEND=y -CONFIG_MMC_UNSAFE_RESUME=y -CONFIG_USB=y -CONFIG_USB_DWC2=y -CONFIG_USB_DWC2_HOST=y -CONFIG_USB_DWC2_PLATFORM=y -- cgit v1.2.3-70-g09d2 From cf355704d681ce7043c732e732b0a23c27d158a8 Mon Sep 17 00:00:00 2001 From: Alexander Sverdlin Date: Thu, 23 Oct 2014 15:55:04 +0200 Subject: MIPS: Octeon: Make Octeon GPIO IRQ chip CPU hotplug-aware Make Octeon GPIO IRQ chip CPU hotplug-aware Seems that irq_cpu_offline callbacks were forgotten in v1 and v2 CIU GPIO chips. There is such a callback for octeon_irq_chip_ciu2_gpio, covering CIU2 chips. Without this callback GPIO IRQs are not being migrated during core offlining. Patch is tested on Octeon II. Signed-off-by: Alexander Sverdlin Cc: David Daney Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/8201/ Signed-off-by: Ralf Baechle --- arch/mips/cavium-octeon/octeon-irq.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/mips/cavium-octeon/octeon-irq.c b/arch/mips/cavium-octeon/octeon-irq.c index 74173404967..2bc4aa95944 100644 --- a/arch/mips/cavium-octeon/octeon-irq.c +++ b/arch/mips/cavium-octeon/octeon-irq.c @@ -809,6 +809,7 @@ static struct irq_chip octeon_irq_chip_ciu_gpio_v2 = { .irq_set_type = octeon_irq_ciu_gpio_set_type, #ifdef CONFIG_SMP .irq_set_affinity = octeon_irq_ciu_set_affinity_v2, + .irq_cpu_offline = octeon_irq_cpu_offline_ciu, #endif .flags = IRQCHIP_SET_TYPE_MASKED, }; @@ -823,6 +824,7 @@ static struct irq_chip octeon_irq_chip_ciu_gpio = { .irq_set_type = octeon_irq_ciu_gpio_set_type, #ifdef CONFIG_SMP .irq_set_affinity = octeon_irq_ciu_set_affinity, + .irq_cpu_offline = octeon_irq_cpu_offline_ciu, #endif .flags = IRQCHIP_SET_TYPE_MASKED, }; -- cgit v1.2.3-70-g09d2 From d5a238df0a29f271069a1d3bb2c58ddec3cb4669 Mon Sep 17 00:00:00 2001 From: Yijing Wang Date: Wed, 15 Oct 2014 11:07:06 +0800 Subject: MIPS/Xlp: Remove the dead function destroy_irq() to fix build error Commit 465665f78a7 ("mips: Kill pointless destroy_irq()") removed the destroy_irq(). So remove the leftover one in xlp_setup_msix() to fix build error. arch/mips/pci/msi-xlp.c: In function 'xlp_setup_msix': arch/mips/pci/msi-xlp.c:447:3: error: implicit declaration of function 'destroy_irq'.. cc1: some warnings being treated as errors make[1]: *** [arch/mips/pci/msi-xlp.o] Error 1 make: *** [arch/mips/pci/] Error 2 Signed-off-by: Yijing Wang Cc: Thomas Gleixner Cc: Bjorn Helgaas Cc: linux-pci@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Xinwei Hu Cc: Wuyun Cc: linux-arm-kernel@lists.infradead.org Cc: Russell King Cc: linux-arch@vger.kernel.org Cc: arnab.basu@freescale.com Cc: Bharat.Bhushan@freescale.com Cc: x86@kernel.org Cc: Arnd Bergmann Cc: Konrad Rzeszutek Wilk Cc: xen-devel@lists.xenproject.org Cc: Joerg Roedel Cc: iommu@lists.linux-foundation.org Cc: linux-mips@linux-mips.org Cc: Benjamin Herrenschmidt Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-s390@vger.kernel.org Cc: Sebastian Ott Cc: Tony Luck Cc: linux-ia64@vger.kernel.org Cc: David S. Miller Cc: sparclinux@vger.kernel.org Cc: Chris Metcalf Cc: Lucas Stach Cc: David Vrabel Cc: Sergei Shtylyov Cc: Michael Ellerman Cc: Thierry Reding Cc: Thomas Petazzoni Cc: Liviu Dudau Patchwork: https://patchwork.linux-mips.org/patch/8087/ Signed-off-by: Ralf Baechle --- arch/mips/pci/msi-xlp.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/arch/mips/pci/msi-xlp.c b/arch/mips/pci/msi-xlp.c index fa374fe3746..f7ac3edda1b 100644 --- a/arch/mips/pci/msi-xlp.c +++ b/arch/mips/pci/msi-xlp.c @@ -443,10 +443,8 @@ static int xlp_setup_msix(uint64_t lnkbase, int node, int link, msg.data = 0xc00 | msixvec; ret = irq_set_msi_desc(xirq, desc); - if (ret < 0) { - destroy_irq(xirq); + if (ret < 0) return ret; - } write_msi_msg(xirq, &msg); return 0; -- cgit v1.2.3-70-g09d2 From 5df4c8dbbc03f4d7e6b6620dcc6869fa989406ee Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Mon, 27 Oct 2014 03:35:53 +0100 Subject: MIPS: Wire up bpf syscall. Signed-off-by: Ralf Baechle --- arch/mips/include/uapi/asm/unistd.h | 15 +++++++++------ arch/mips/kernel/scall32-o32.S | 1 + arch/mips/kernel/scall64-64.S | 1 + arch/mips/kernel/scall64-n32.S | 1 + arch/mips/kernel/scall64-o32.S | 1 + 5 files changed, 13 insertions(+), 6 deletions(-) diff --git a/arch/mips/include/uapi/asm/unistd.h b/arch/mips/include/uapi/asm/unistd.h index fdb4923777d..9dc58568f23 100644 --- a/arch/mips/include/uapi/asm/unistd.h +++ b/arch/mips/include/uapi/asm/unistd.h @@ -375,16 +375,17 @@ #define __NR_seccomp (__NR_Linux + 352) #define __NR_getrandom (__NR_Linux + 353) #define __NR_memfd_create (__NR_Linux + 354) +#define __NR_bpf (__NR_Linux + 355) /* * Offset of the last Linux o32 flavoured syscall */ -#define __NR_Linux_syscalls 354 +#define __NR_Linux_syscalls 355 #endif /* _MIPS_SIM == _MIPS_SIM_ABI32 */ #define __NR_O32_Linux 4000 -#define __NR_O32_Linux_syscalls 354 +#define __NR_O32_Linux_syscalls 355 #if _MIPS_SIM == _MIPS_SIM_ABI64 @@ -707,16 +708,17 @@ #define __NR_seccomp (__NR_Linux + 312) #define __NR_getrandom (__NR_Linux + 313) #define __NR_memfd_create (__NR_Linux + 314) +#define __NR_bpf (__NR_Linux + 315) /* * Offset of the last Linux 64-bit flavoured syscall */ -#define __NR_Linux_syscalls 314 +#define __NR_Linux_syscalls 315 #endif /* _MIPS_SIM == _MIPS_SIM_ABI64 */ #define __NR_64_Linux 5000 -#define __NR_64_Linux_syscalls 314 +#define __NR_64_Linux_syscalls 315 #if _MIPS_SIM == _MIPS_SIM_NABI32 @@ -1043,15 +1045,16 @@ #define __NR_seccomp (__NR_Linux + 316) #define __NR_getrandom (__NR_Linux + 317) #define __NR_memfd_create (__NR_Linux + 318) +#define __NR_memfd_create (__NR_Linux + 319) /* * Offset of the last N32 flavoured syscall */ -#define __NR_Linux_syscalls 318 +#define __NR_Linux_syscalls 319 #endif /* _MIPS_SIM == _MIPS_SIM_NABI32 */ #define __NR_N32_Linux 6000 -#define __NR_N32_Linux_syscalls 318 +#define __NR_N32_Linux_syscalls 319 #endif /* _UAPI_ASM_UNISTD_H */ diff --git a/arch/mips/kernel/scall32-o32.S b/arch/mips/kernel/scall32-o32.S index 744cd10ba59..00cad1005a1 100644 --- a/arch/mips/kernel/scall32-o32.S +++ b/arch/mips/kernel/scall32-o32.S @@ -579,3 +579,4 @@ EXPORT(sys_call_table) PTR sys_seccomp PTR sys_getrandom PTR sys_memfd_create + PTR sys_bpf /* 4355 */ diff --git a/arch/mips/kernel/scall64-64.S b/arch/mips/kernel/scall64-64.S index 002b1bc09c3..5251565e344 100644 --- a/arch/mips/kernel/scall64-64.S +++ b/arch/mips/kernel/scall64-64.S @@ -434,4 +434,5 @@ EXPORT(sys_call_table) PTR sys_seccomp PTR sys_getrandom PTR sys_memfd_create + PTR sys_bpf /* 5315 */ .size sys_call_table,.-sys_call_table diff --git a/arch/mips/kernel/scall64-n32.S b/arch/mips/kernel/scall64-n32.S index ca6cbbe9805..77e74398b82 100644 --- a/arch/mips/kernel/scall64-n32.S +++ b/arch/mips/kernel/scall64-n32.S @@ -427,4 +427,5 @@ EXPORT(sysn32_call_table) PTR sys_seccomp PTR sys_getrandom PTR sys_memfd_create + PTR sys_bpf .size sysn32_call_table,.-sysn32_call_table diff --git a/arch/mips/kernel/scall64-o32.S b/arch/mips/kernel/scall64-o32.S index 9e10d11fbb8..6f8db9f728e 100644 --- a/arch/mips/kernel/scall64-o32.S +++ b/arch/mips/kernel/scall64-o32.S @@ -564,4 +564,5 @@ EXPORT(sys32_call_table) PTR sys_seccomp PTR sys_getrandom PTR sys_memfd_create + PTR sys_bpf /* 4355 */ .size sys32_call_table,.-sys32_call_table -- cgit v1.2.3-70-g09d2 From f7bbd12a4b7e088f53f20dd31019984459699fb9 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Thu, 9 Oct 2014 20:30:06 +0200 Subject: m68k: Wire up bpf Signed-off-by: Geert Uytterhoeven Acked-by: Alexei Starovoitov --- arch/m68k/include/asm/unistd.h | 2 +- arch/m68k/include/uapi/asm/unistd.h | 1 + arch/m68k/kernel/syscalltable.S | 1 + 3 files changed, 3 insertions(+), 1 deletion(-) diff --git a/arch/m68k/include/asm/unistd.h b/arch/m68k/include/asm/unistd.h index 4ef7a54813e..75e75d7b170 100644 --- a/arch/m68k/include/asm/unistd.h +++ b/arch/m68k/include/asm/unistd.h @@ -4,7 +4,7 @@ #include -#define NR_syscalls 354 +#define NR_syscalls 355 #define __ARCH_WANT_OLD_READDIR #define __ARCH_WANT_OLD_STAT diff --git a/arch/m68k/include/uapi/asm/unistd.h b/arch/m68k/include/uapi/asm/unistd.h index b419c6b7ac3..2c1bec9a14b 100644 --- a/arch/m68k/include/uapi/asm/unistd.h +++ b/arch/m68k/include/uapi/asm/unistd.h @@ -359,5 +359,6 @@ #define __NR_renameat2 351 #define __NR_getrandom 352 #define __NR_memfd_create 353 +#define __NR_bpf 354 #endif /* _UAPI_ASM_M68K_UNISTD_H_ */ diff --git a/arch/m68k/kernel/syscalltable.S b/arch/m68k/kernel/syscalltable.S index 05b46c2b08b..2ca219e184c 100644 --- a/arch/m68k/kernel/syscalltable.S +++ b/arch/m68k/kernel/syscalltable.S @@ -374,4 +374,5 @@ ENTRY(sys_call_table) .long sys_renameat2 .long sys_getrandom .long sys_memfd_create + .long sys_bpf -- cgit v1.2.3-70-g09d2 From f022d8cb7ec70fe8edd56383d876001317ee76b1 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Fri, 24 Oct 2014 13:18:39 +0300 Subject: mm: cma: Don't crash on allocation if CMA area can't be activated If activation of the CMA area fails its mutex won't be initialized, leading to an oops at allocation time when trying to lock the mutex. Fix this by setting the cma area count field to 0 when activation fails, leading to allocation returning NULL immediately. Cc: # v3.17 Signed-off-by: Laurent Pinchart Acked-by: Michal Nazarewicz Signed-off-by: Marek Szyprowski --- mm/cma.c | 1 + 1 file changed, 1 insertion(+) diff --git a/mm/cma.c b/mm/cma.c index 963bc4add9a..5aa1a6f74de 100644 --- a/mm/cma.c +++ b/mm/cma.c @@ -124,6 +124,7 @@ static int __init cma_activate_area(struct cma *cma) err: kfree(cma->bitmap); + cma->count = 0; return -EINVAL; } -- cgit v1.2.3-70-g09d2 From 800a85d3d286604b8c539ca7ee90b992316fd2a7 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Fri, 24 Oct 2014 13:18:40 +0300 Subject: mm: cma: Always consider a 0 base address reservation as dynamic The fixed parameter to cma_declare_contiguous() tells the function whether the given base address must be honoured or should be considered as a hint only. The API considers a zero base address as meaning any base address, which must never be considered as a fixed value. Part of the implementation correctly checks both fixed and base != 0, but two locations check the fixed value only. Set fixed to false when base is 0 to fix that and simplify the code. Signed-off-by: Laurent Pinchart Acked-by: Michal Nazarewicz Signed-off-by: Marek Szyprowski --- mm/cma.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/mm/cma.c b/mm/cma.c index 5aa1a6f74de..62a5dccc3fb 100644 --- a/mm/cma.c +++ b/mm/cma.c @@ -245,6 +245,9 @@ int __init cma_declare_contiguous(phys_addr_t base, size = ALIGN(size, alignment); limit &= ~(alignment - 1); + if (!base) + fixed = false; + /* size should be aligned with order_per_bit */ if (!IS_ALIGNED(size >> PAGE_SHIFT, 1 << order_per_bit)) return -EINVAL; @@ -268,7 +271,7 @@ int __init cma_declare_contiguous(phys_addr_t base, } /* Reserve memory */ - if (base && fixed) { + if (fixed) { if (memblock_is_region_reserved(base, size) || memblock_reserve(base, size) < 0) { ret = -EBUSY; -- cgit v1.2.3-70-g09d2 From 16195ddd4ebcc10c30b2f232f8e400df8d464380 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Fri, 24 Oct 2014 13:18:41 +0300 Subject: mm: cma: Ensure that reservations never cross the low/high mem boundary Commit 95b0e655f914 ("ARM: mm: don't limit default CMA region only to low memory") extended CMA memory reservation to allow usage of high memory. It relied on commit f7426b983a6a ("mm: cma: adjust address limit to avoid hitting low/high memory boundary") to ensure that the reserved block never crossed the low/high memory boundary. While the implementation correctly lowered the limit, it failed to consider the case where the base..limit range crossed the low/high memory boundary with enough space on each side to reserve the requested size on either low or high memory. Rework the base and limit adjustment to fix the problem. The function now starts by rejecting the reservation altogether for fixed reservations that cross the boundary, tries to reserve from high memory first and then falls back to low memory. Signed-off-by: Laurent Pinchart Signed-off-by: Marek Szyprowski --- mm/cma.c | 49 +++++++++++++++++++++++++++++++++---------------- 1 file changed, 33 insertions(+), 16 deletions(-) diff --git a/mm/cma.c b/mm/cma.c index 62a5dccc3fb..c30a6edee65 100644 --- a/mm/cma.c +++ b/mm/cma.c @@ -253,23 +253,24 @@ int __init cma_declare_contiguous(phys_addr_t base, return -EINVAL; /* - * adjust limit to avoid crossing low/high memory boundary for - * automatically allocated regions + * If allocating at a fixed base the request region must not cross the + * low/high memory boundary. */ - if (((limit == 0 || limit > memblock_end) && - (memblock_end - size < highmem_start && - memblock_end > highmem_start)) || - (!fixed && limit > highmem_start && limit - size < highmem_start)) { - limit = highmem_start; - } - - if (fixed && base < highmem_start && base+size > highmem_start) { + if (fixed && base < highmem_start && base + size > highmem_start) { ret = -EINVAL; pr_err("Region at %08lx defined on low/high memory boundary (%08lx)\n", (unsigned long)base, (unsigned long)highmem_start); goto err; } + /* + * If the limit is unspecified or above the memblock end, its effective + * value will be the memblock end. Set it explicitly to simplify further + * checks. + */ + if (limit == 0 || limit > memblock_end) + limit = memblock_end; + /* Reserve memory */ if (fixed) { if (memblock_is_region_reserved(base, size) || @@ -278,14 +279,30 @@ int __init cma_declare_contiguous(phys_addr_t base, goto err; } } else { - phys_addr_t addr = memblock_alloc_range(size, alignment, base, - limit); + phys_addr_t addr = 0; + + /* + * All pages in the reserved area must come from the same zone. + * If the requested region crosses the low/high memory boundary, + * try allocating from high memory first and fall back to low + * memory in case of failure. + */ + if (base < highmem_start && limit > highmem_start) { + addr = memblock_alloc_range(size, alignment, + highmem_start, limit); + limit = highmem_start; + } + if (!addr) { - ret = -ENOMEM; - goto err; - } else { - base = addr; + addr = memblock_alloc_range(size, alignment, base, + limit); + if (!addr) { + ret = -ENOMEM; + goto err; + } } + + base = addr; } ret = cma_init_reserved_mem(base, size, order_per_bit, res_cma); -- cgit v1.2.3-70-g09d2 From 56fa4f609badbe442093409c3d3a051811e54f72 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Fri, 24 Oct 2014 13:18:42 +0300 Subject: mm: cma: Use %pa to print physical addresses Casting physical addresses to unsigned long and using %lu truncates the values on systems where physical addresses are larger than 32 bits. Use %pa and get rid of the cast instead. Signed-off-by: Laurent Pinchart Acked-by: Michal Nazarewicz Acked-by: Geert Uytterhoeven Signed-off-by: Marek Szyprowski --- mm/cma.c | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-) diff --git a/mm/cma.c b/mm/cma.c index c30a6edee65..fde706e1284 100644 --- a/mm/cma.c +++ b/mm/cma.c @@ -218,9 +218,8 @@ int __init cma_declare_contiguous(phys_addr_t base, phys_addr_t highmem_start = __pa(high_memory); int ret = 0; - pr_debug("%s(size %lx, base %08lx, limit %08lx alignment %08lx)\n", - __func__, (unsigned long)size, (unsigned long)base, - (unsigned long)limit, (unsigned long)alignment); + pr_debug("%s(size %pa, base %pa, limit %pa alignment %pa)\n", + __func__, &size, &base, &limit, &alignment); if (cma_area_count == ARRAY_SIZE(cma_areas)) { pr_err("Not enough slots for CMA reserved regions!\n"); @@ -258,8 +257,8 @@ int __init cma_declare_contiguous(phys_addr_t base, */ if (fixed && base < highmem_start && base + size > highmem_start) { ret = -EINVAL; - pr_err("Region at %08lx defined on low/high memory boundary (%08lx)\n", - (unsigned long)base, (unsigned long)highmem_start); + pr_err("Region at %pa defined on low/high memory boundary (%pa)\n", + &base, &highmem_start); goto err; } @@ -309,8 +308,8 @@ int __init cma_declare_contiguous(phys_addr_t base, if (ret) goto err; - pr_info("Reserved %ld MiB at %08lx\n", (unsigned long)size / SZ_1M, - (unsigned long)base); + pr_info("Reserved %ld MiB at %pa\n", (unsigned long)size / SZ_1M, + &base); return 0; err: -- cgit v1.2.3-70-g09d2 From dda02fd6278d9e995850b3c1dba484f17cbe4de4 Mon Sep 17 00:00:00 2001 From: Weijie Yang Date: Fri, 24 Oct 2014 17:47:57 +0800 Subject: mm, cma: make parameters order consistent in func declaration and definition In the current code, the base and size parameters order is not consistent in functions declaration and definition. If someone calls these functions according to the declaration parameters order in cma.h, he will run into some bug and it's hard to find the reason. This patch makes the parameters order consistent in functions declaration and definition. Signed-off-by: Weijie Yang Acked-by: Michal Nazarewicz Signed-off-by: Marek Szyprowski --- include/linux/cma.h | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/include/linux/cma.h b/include/linux/cma.h index 0430ed05d3b..a93438beb33 100644 --- a/include/linux/cma.h +++ b/include/linux/cma.h @@ -18,12 +18,12 @@ struct cma; extern phys_addr_t cma_get_base(struct cma *cma); extern unsigned long cma_get_size(struct cma *cma); -extern int __init cma_declare_contiguous(phys_addr_t size, - phys_addr_t base, phys_addr_t limit, +extern int __init cma_declare_contiguous(phys_addr_t base, + phys_addr_t size, phys_addr_t limit, phys_addr_t alignment, unsigned int order_per_bit, bool fixed, struct cma **res_cma); -extern int cma_init_reserved_mem(phys_addr_t size, - phys_addr_t base, int order_per_bit, +extern int cma_init_reserved_mem(phys_addr_t base, + phys_addr_t size, int order_per_bit, struct cma **res_cma); extern struct page *cma_alloc(struct cma *cma, int count, unsigned int align); extern bool cma_release(struct cma *cma, struct page *pages, int count); -- cgit v1.2.3-70-g09d2 From 1f759bb3a2a0d75ceeeec729b1c66a7f443631ba Mon Sep 17 00:00:00 2001 From: Martin Schwidefsky Date: Mon, 20 Oct 2014 10:24:39 +0200 Subject: s390/time: use stck clock fast for do_account_vtime The last high frequency call site of the STCK instruction is do_account_vtime. Replace it with the faster STCKF instruction. Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/vtime.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/s390/kernel/vtime.c b/arch/s390/kernel/vtime.c index 416f2a323ba..7f0089d9a4a 100644 --- a/arch/s390/kernel/vtime.c +++ b/arch/s390/kernel/vtime.c @@ -66,7 +66,11 @@ static int do_account_vtime(struct task_struct *tsk, int hardirq_offset) clock = S390_lowcore.last_update_clock; asm volatile( " stpt %0\n" /* Store current cpu timer value */ +#ifdef CONFIG_HAVE_MARCH_Z9_109_FEATURES + " stckf %1" /* Store current tod clock value */ +#else " stck %1" /* Store current tod clock value */ +#endif : "=m" (S390_lowcore.last_update_timer), "=m" (S390_lowcore.last_update_clock)); S390_lowcore.system_timer += timer - S390_lowcore.last_update_timer; -- cgit v1.2.3-70-g09d2 From 9b2efe035eafb1a29ff3dfe21ed0e755aac09130 Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Mon, 27 Oct 2014 08:28:08 +0100 Subject: s390/vdso: fix stack corruption The kernel provided vdso functions do not get a stack frame from the calling function and therefore may not change the stack contents, unless they allocate space on their own. This problem was exposed with 070b7be633dc "s390/vdso: replace stck with stcke" which writes 16 bytes instead of 8 bytes into the stack frame. These additional 8 bytes however were indeed used by the caller (glibc) to save data and therefore this data was corrupted by the vdso code. Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/vdso32/clock_gettime.S | 12 ++++++++---- arch/s390/kernel/vdso32/gettimeofday.S | 14 ++++++++------ arch/s390/kernel/vdso64/clock_gettime.S | 13 +++++++++---- arch/s390/kernel/vdso64/gettimeofday.S | 6 ++++-- 4 files changed, 29 insertions(+), 16 deletions(-) diff --git a/arch/s390/kernel/vdso32/clock_gettime.S b/arch/s390/kernel/vdso32/clock_gettime.S index 48c2206a395..5eec9afbb5b 100644 --- a/arch/s390/kernel/vdso32/clock_gettime.S +++ b/arch/s390/kernel/vdso32/clock_gettime.S @@ -19,6 +19,7 @@ .type __kernel_clock_gettime,@function __kernel_clock_gettime: .cfi_startproc + ahi %r15,-16 basr %r5,0 0: al %r5,21f-0b(%r5) /* get &_vdso_data */ chi %r2,__CLOCK_REALTIME_COARSE @@ -34,8 +35,8 @@ __kernel_clock_gettime: 1: l %r4,__VDSO_UPD_COUNT+4(%r5) /* load update counter */ tml %r4,0x0001 /* pending update ? loop */ jnz 1b - stcke 24(%r15) /* Store TOD clock */ - lm %r0,%r1,25(%r15) + stcke 0(%r15) /* Store TOD clock */ + lm %r0,%r1,1(%r15) s %r0,__VDSO_XTIME_STAMP(%r5) /* TOD - cycle_last */ sl %r1,__VDSO_XTIME_STAMP+4(%r5) brc 3,2f @@ -70,6 +71,7 @@ __kernel_clock_gettime: 8: st %r2,0(%r3) /* store tp->tv_sec */ st %r1,4(%r3) /* store tp->tv_nsec */ lhi %r2,0 + ahi %r15,16 br %r14 /* CLOCK_MONOTONIC_COARSE */ @@ -96,8 +98,8 @@ __kernel_clock_gettime: 11: l %r4,__VDSO_UPD_COUNT+4(%r5) /* load update counter */ tml %r4,0x0001 /* pending update ? loop */ jnz 11b - stcke 24(%r15) /* Store TOD clock */ - lm %r0,%r1,25(%r15) + stcke 0(%r15) /* Store TOD clock */ + lm %r0,%r1,1(%r15) s %r0,__VDSO_XTIME_STAMP(%r5) /* TOD - cycle_last */ sl %r1,__VDSO_XTIME_STAMP+4(%r5) brc 3,12f @@ -132,11 +134,13 @@ __kernel_clock_gettime: 17: st %r2,0(%r3) /* store tp->tv_sec */ st %r1,4(%r3) /* store tp->tv_nsec */ lhi %r2,0 + ahi %r15,16 br %r14 /* Fallback to system call */ 19: lhi %r1,__NR_clock_gettime svc 0 + ahi %r15,16 br %r14 20: .long 1000000000 diff --git a/arch/s390/kernel/vdso32/gettimeofday.S b/arch/s390/kernel/vdso32/gettimeofday.S index 60def5f562d..719de6186b2 100644 --- a/arch/s390/kernel/vdso32/gettimeofday.S +++ b/arch/s390/kernel/vdso32/gettimeofday.S @@ -19,6 +19,7 @@ .type __kernel_gettimeofday,@function __kernel_gettimeofday: .cfi_startproc + ahi %r15,-16 basr %r5,0 0: al %r5,13f-0b(%r5) /* get &_vdso_data */ 1: ltr %r3,%r3 /* check if tz is NULL */ @@ -29,30 +30,30 @@ __kernel_gettimeofday: l %r4,__VDSO_UPD_COUNT+4(%r5) /* load update counter */ tml %r4,0x0001 /* pending update ? loop */ jnz 1b - stcke 24(%r15) /* Store TOD clock */ - lm %r0,%r1,25(%r15) + stcke 0(%r15) /* Store TOD clock */ + lm %r0,%r1,1(%r15) s %r0,__VDSO_XTIME_STAMP(%r5) /* TOD - cycle_last */ sl %r1,__VDSO_XTIME_STAMP+4(%r5) brc 3,3f ahi %r0,-1 3: ms %r0,__VDSO_TK_MULT(%r5) /* * tk->mult */ - st %r0,24(%r15) + st %r0,0(%r15) l %r0,__VDSO_TK_MULT(%r5) ltr %r1,%r1 mr %r0,%r0 jnm 4f a %r0,__VDSO_TK_MULT(%r5) -4: al %r0,24(%r15) +4: al %r0,0(%r15) al %r0,__VDSO_XTIME_NSEC(%r5) /* + xtime */ al %r1,__VDSO_XTIME_NSEC+4(%r5) brc 12,5f ahi %r0,1 -5: mvc 24(4,%r15),__VDSO_XTIME_SEC+4(%r5) +5: mvc 0(4,%r15),__VDSO_XTIME_SEC+4(%r5) cl %r4,__VDSO_UPD_COUNT+4(%r5) /* check update counter */ jne 1b l %r4,__VDSO_TK_SHIFT(%r5) /* Timekeeper shift */ srdl %r0,0(%r4) /* >> tk->shift */ - l %r4,24(%r15) /* get tv_sec from stack */ + l %r4,0(%r15) /* get tv_sec from stack */ basr %r5,0 6: ltr %r0,%r0 jnz 7f @@ -71,6 +72,7 @@ __kernel_gettimeofday: 9: srl %r0,6 st %r0,4(%r2) /* store tv->tv_usec */ 10: slr %r2,%r2 + ahi %r15,16 br %r14 11: .long 1000000000 12: .long 274877907 diff --git a/arch/s390/kernel/vdso64/clock_gettime.S b/arch/s390/kernel/vdso64/clock_gettime.S index 9d9761f8e11..7699e735ae2 100644 --- a/arch/s390/kernel/vdso64/clock_gettime.S +++ b/arch/s390/kernel/vdso64/clock_gettime.S @@ -19,6 +19,7 @@ .type __kernel_clock_gettime,@function __kernel_clock_gettime: .cfi_startproc + aghi %r15,-16 larl %r5,_vdso_data cghi %r2,__CLOCK_REALTIME_COARSE je 4f @@ -37,10 +38,10 @@ __kernel_clock_gettime: 0: lg %r4,__VDSO_UPD_COUNT(%r5) /* load update counter */ tmll %r4,0x0001 /* pending update ? loop */ jnz 0b - stcke 48(%r15) /* Store TOD clock */ + stcke 0(%r15) /* Store TOD clock */ lgf %r2,__VDSO_TK_SHIFT(%r5) /* Timekeeper shift */ lg %r0,__VDSO_WTOM_SEC(%r5) - lg %r1,49(%r15) + lg %r1,1(%r15) sg %r1,__VDSO_XTIME_STAMP(%r5) /* TOD - cycle_last */ msgf %r1,__VDSO_TK_MULT(%r5) /* * tk->mult */ alg %r1,__VDSO_WTOM_NSEC(%r5) @@ -56,6 +57,7 @@ __kernel_clock_gettime: 2: stg %r0,0(%r3) /* store tp->tv_sec */ stg %r1,8(%r3) /* store tp->tv_nsec */ lghi %r2,0 + aghi %r15,16 br %r14 /* CLOCK_MONOTONIC_COARSE */ @@ -82,9 +84,9 @@ __kernel_clock_gettime: 5: lg %r4,__VDSO_UPD_COUNT(%r5) /* load update counter */ tmll %r4,0x0001 /* pending update ? loop */ jnz 5b - stcke 48(%r15) /* Store TOD clock */ + stcke 0(%r15) /* Store TOD clock */ lgf %r2,__VDSO_TK_SHIFT(%r5) /* Timekeeper shift */ - lg %r1,49(%r15) + lg %r1,1(%r15) sg %r1,__VDSO_XTIME_STAMP(%r5) /* TOD - cycle_last */ msgf %r1,__VDSO_TK_MULT(%r5) /* * tk->mult */ alg %r1,__VDSO_XTIME_NSEC(%r5) /* + tk->xtime_nsec */ @@ -101,6 +103,7 @@ __kernel_clock_gettime: 7: stg %r0,0(%r3) /* store tp->tv_sec */ stg %r1,8(%r3) /* store tp->tv_nsec */ lghi %r2,0 + aghi %r15,16 br %r14 /* CLOCK_THREAD_CPUTIME_ID for this thread */ @@ -134,11 +137,13 @@ __kernel_clock_gettime: slgr %r4,%r0 /* r4 = tv_nsec */ stg %r4,8(%r3) lghi %r2,0 + aghi %r15,16 br %r14 /* Fallback to system call */ 12: lghi %r1,__NR_clock_gettime svc 0 + aghi %r15,16 br %r14 13: .quad 1000000000 diff --git a/arch/s390/kernel/vdso64/gettimeofday.S b/arch/s390/kernel/vdso64/gettimeofday.S index 7a344995a97..6ce46707663 100644 --- a/arch/s390/kernel/vdso64/gettimeofday.S +++ b/arch/s390/kernel/vdso64/gettimeofday.S @@ -19,6 +19,7 @@ .type __kernel_gettimeofday,@function __kernel_gettimeofday: .cfi_startproc + aghi %r15,-16 larl %r5,_vdso_data 0: ltgr %r3,%r3 /* check if tz is NULL */ je 1f @@ -28,8 +29,8 @@ __kernel_gettimeofday: lg %r4,__VDSO_UPD_COUNT(%r5) /* load update counter */ tmll %r4,0x0001 /* pending update ? loop */ jnz 0b - stcke 48(%r15) /* Store TOD clock */ - lg %r1,49(%r15) + stcke 0(%r15) /* Store TOD clock */ + lg %r1,1(%r15) sg %r1,__VDSO_XTIME_STAMP(%r5) /* TOD - cycle_last */ msgf %r1,__VDSO_TK_MULT(%r5) /* * tk->mult */ alg %r1,__VDSO_XTIME_NSEC(%r5) /* + tk->xtime_nsec */ @@ -50,6 +51,7 @@ __kernel_gettimeofday: srlg %r0,%r0,6 stg %r0,8(%r2) /* store tv->tv_usec */ 4: lghi %r2,0 + aghi %r15,16 br %r14 5: .quad 1000000000 .long 274877907 -- cgit v1.2.3-70-g09d2 From e43b49a0cb9c9ea958edcf7520aae2490549c68b Mon Sep 17 00:00:00 2001 From: Martin Schwidefsky Date: Mon, 16 Jun 2014 10:21:31 -0700 Subject: s390: update default configuration Signed-off-by: Martin Schwidefsky --- arch/s390/configs/default_defconfig | 36 +++++++++++++-------------------- arch/s390/configs/gcov_defconfig | 25 +++++------------------ arch/s390/configs/performance_defconfig | 30 +++++++++------------------ arch/s390/configs/zfcpdump_defconfig | 10 ++------- arch/s390/defconfig | 5 ++--- 5 files changed, 32 insertions(+), 74 deletions(-) diff --git a/arch/s390/configs/default_defconfig b/arch/s390/configs/default_defconfig index 9d94fdd9f52..9432d0f202e 100644 --- a/arch/s390/configs/default_defconfig +++ b/arch/s390/configs/default_defconfig @@ -35,7 +35,6 @@ CONFIG_MODULE_UNLOAD=y CONFIG_MODULE_FORCE_UNLOAD=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y -CONFIG_BLK_DEV_INTEGRITY=y CONFIG_BLK_DEV_THROTTLING=y CONFIG_PARTITION_ADVANCED=y CONFIG_IBM_PARTITION=y @@ -245,6 +244,7 @@ CONFIG_NF_TABLES_IPV4=m CONFIG_NFT_CHAIN_ROUTE_IPV4=m CONFIG_NFT_CHAIN_NAT_IPV4=m CONFIG_NF_TABLES_ARP=m +CONFIG_NF_NAT_IPV4=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_AH=m CONFIG_IP_NF_MATCH_ECN=m @@ -252,11 +252,6 @@ CONFIG_IP_NF_MATCH_RPFILTER=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m -CONFIG_IP_NF_TARGET_ULOG=m -CONFIG_NF_NAT_IPV4=m -CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_NETMAP=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m @@ -270,6 +265,7 @@ CONFIG_NF_CONNTRACK_IPV6=m CONFIG_NF_TABLES_IPV6=m CONFIG_NFT_CHAIN_ROUTE_IPV6=m CONFIG_NFT_CHAIN_NAT_IPV6=m +CONFIG_NF_NAT_IPV6=m CONFIG_IP6_NF_IPTABLES=m CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_EUI64=m @@ -286,9 +282,6 @@ CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_RAW=m CONFIG_IP6_NF_SECURITY=m -CONFIG_NF_NAT_IPV6=m -CONFIG_IP6_NF_TARGET_MASQUERADE=m -CONFIG_IP6_NF_TARGET_NPT=m CONFIG_NF_TABLES_BRIDGE=m CONFIG_NET_SCTPPROBE=m CONFIG_RDS=m @@ -374,14 +367,13 @@ CONFIG_BLK_DEV_SR=m CONFIG_CHR_DEV_SG=y CONFIG_CHR_DEV_SCH=m CONFIG_SCSI_ENCLOSURE=m -CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_LOGGING=y CONFIG_SCSI_SPI_ATTRS=m +CONFIG_SCSI_FC_ATTRS=y CONFIG_SCSI_SAS_LIBSAS=m CONFIG_SCSI_SRP_ATTRS=m CONFIG_ISCSI_TCP=m -CONFIG_LIBFCOE=m CONFIG_SCSI_DEBUG=m CONFIG_ZFCP=y CONFIG_SCSI_VIRTIO=m @@ -427,7 +419,6 @@ CONFIG_VIRTIO_NET=m CONFIG_NLMON=m CONFIG_VHOST_NET=m # CONFIG_NET_VENDOR_ARC is not set -# CONFIG_NET_CADENCE is not set # CONFIG_NET_VENDOR_CHELSIO is not set # CONFIG_NET_VENDOR_INTEL is not set # CONFIG_NET_VENDOR_MARVELL is not set @@ -481,14 +472,14 @@ CONFIG_JFS_FS=m CONFIG_JFS_POSIX_ACL=y CONFIG_JFS_SECURITY=y CONFIG_JFS_STATISTICS=y -CONFIG_XFS_FS=m +CONFIG_XFS_FS=y CONFIG_XFS_QUOTA=y CONFIG_XFS_POSIX_ACL=y CONFIG_XFS_RT=y CONFIG_XFS_DEBUG=y CONFIG_GFS2_FS=m CONFIG_OCFS2_FS=m -CONFIG_BTRFS_FS=m +CONFIG_BTRFS_FS=y CONFIG_BTRFS_FS_POSIX_ACL=y CONFIG_NILFS2_FS=m CONFIG_FANOTIFY=y @@ -574,7 +565,6 @@ CONFIG_DEBUG_SHIRQ=y CONFIG_DETECT_HUNG_TASK=y CONFIG_TIMER_STATS=y CONFIG_DEBUG_RT_MUTEXES=y -CONFIG_RT_MUTEX_TESTER=y CONFIG_DEBUG_WW_MUTEX_SLOWPATH=y CONFIG_PROVE_LOCKING=y CONFIG_LOCK_STAT=y @@ -600,8 +590,13 @@ CONFIG_FAULT_INJECTION_DEBUG_FS=y CONFIG_FAULT_INJECTION_STACKTRACE_FILTER=y CONFIG_LATENCYTOP=y CONFIG_DEBUG_STRICT_USER_COPY_CHECKS=y +CONFIG_IRQSOFF_TRACER=y +CONFIG_PREEMPT_TRACER=y +CONFIG_SCHED_TRACER=y +CONFIG_FTRACE_SYSCALLS=y +CONFIG_STACK_TRACER=y CONFIG_BLK_DEV_IO_TRACE=y -# CONFIG_KPROBE_EVENT is not set +CONFIG_UPROBE_EVENT=y CONFIG_LKDTM=m CONFIG_TEST_LIST_SORT=y CONFIG_KPROBES_SANITY_TEST=y @@ -609,7 +604,10 @@ CONFIG_RBTREE_TEST=y CONFIG_INTERVAL_TREE_TEST=m CONFIG_PERCPU_TEST=m CONFIG_ATOMIC64_SELFTEST=y +CONFIG_TEST_STRING_HELPERS=y +CONFIG_TEST_KSTRTOX=y CONFIG_DMA_API_DEBUG=y +CONFIG_TEST_BPF=m # CONFIG_STRICT_DEVMEM is not set CONFIG_S390_PTDUMP=y CONFIG_ENCRYPTED_KEYS=m @@ -673,12 +671,6 @@ CONFIG_ASYMMETRIC_PUBLIC_KEY_SUBTYPE=m CONFIG_X509_CERTIFICATE_PARSER=m CONFIG_CRC7=m CONFIG_CRC8=m -CONFIG_XZ_DEC_X86=y -CONFIG_XZ_DEC_POWERPC=y -CONFIG_XZ_DEC_IA64=y -CONFIG_XZ_DEC_ARM=y -CONFIG_XZ_DEC_ARMTHUMB=y -CONFIG_XZ_DEC_SPARC=y CONFIG_CORDIC=m CONFIG_CMM=m CONFIG_APPLDATA_BASE=y diff --git a/arch/s390/configs/gcov_defconfig b/arch/s390/configs/gcov_defconfig index 90f514baa37..219dca6ea92 100644 --- a/arch/s390/configs/gcov_defconfig +++ b/arch/s390/configs/gcov_defconfig @@ -35,7 +35,6 @@ CONFIG_MODULE_UNLOAD=y CONFIG_MODULE_FORCE_UNLOAD=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y -CONFIG_BLK_DEV_INTEGRITY=y CONFIG_BLK_DEV_THROTTLING=y CONFIG_PARTITION_ADVANCED=y CONFIG_IBM_PARTITION=y @@ -243,6 +242,7 @@ CONFIG_NF_TABLES_IPV4=m CONFIG_NFT_CHAIN_ROUTE_IPV4=m CONFIG_NFT_CHAIN_NAT_IPV4=m CONFIG_NF_TABLES_ARP=m +CONFIG_NF_NAT_IPV4=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_AH=m CONFIG_IP_NF_MATCH_ECN=m @@ -250,11 +250,6 @@ CONFIG_IP_NF_MATCH_RPFILTER=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m -CONFIG_IP_NF_TARGET_ULOG=m -CONFIG_NF_NAT_IPV4=m -CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_NETMAP=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m @@ -268,6 +263,7 @@ CONFIG_NF_CONNTRACK_IPV6=m CONFIG_NF_TABLES_IPV6=m CONFIG_NFT_CHAIN_ROUTE_IPV6=m CONFIG_NFT_CHAIN_NAT_IPV6=m +CONFIG_NF_NAT_IPV6=m CONFIG_IP6_NF_IPTABLES=m CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_EUI64=m @@ -284,9 +280,6 @@ CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_RAW=m CONFIG_IP6_NF_SECURITY=m -CONFIG_NF_NAT_IPV6=m -CONFIG_IP6_NF_TARGET_MASQUERADE=m -CONFIG_IP6_NF_TARGET_NPT=m CONFIG_NF_TABLES_BRIDGE=m CONFIG_NET_SCTPPROBE=m CONFIG_RDS=m @@ -371,14 +364,13 @@ CONFIG_BLK_DEV_SR=m CONFIG_CHR_DEV_SG=y CONFIG_CHR_DEV_SCH=m CONFIG_SCSI_ENCLOSURE=m -CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_LOGGING=y CONFIG_SCSI_SPI_ATTRS=m +CONFIG_SCSI_FC_ATTRS=y CONFIG_SCSI_SAS_LIBSAS=m CONFIG_SCSI_SRP_ATTRS=m CONFIG_ISCSI_TCP=m -CONFIG_LIBFCOE=m CONFIG_SCSI_DEBUG=m CONFIG_ZFCP=y CONFIG_SCSI_VIRTIO=m @@ -424,7 +416,6 @@ CONFIG_VIRTIO_NET=m CONFIG_NLMON=m CONFIG_VHOST_NET=m # CONFIG_NET_VENDOR_ARC is not set -# CONFIG_NET_CADENCE is not set # CONFIG_NET_VENDOR_CHELSIO is not set # CONFIG_NET_VENDOR_INTEL is not set # CONFIG_NET_VENDOR_MARVELL is not set @@ -478,13 +469,13 @@ CONFIG_JFS_FS=m CONFIG_JFS_POSIX_ACL=y CONFIG_JFS_SECURITY=y CONFIG_JFS_STATISTICS=y -CONFIG_XFS_FS=m +CONFIG_XFS_FS=y CONFIG_XFS_QUOTA=y CONFIG_XFS_POSIX_ACL=y CONFIG_XFS_RT=y CONFIG_GFS2_FS=m CONFIG_OCFS2_FS=m -CONFIG_BTRFS_FS=m +CONFIG_BTRFS_FS=y CONFIG_BTRFS_FS_POSIX_ACL=y CONFIG_NILFS2_FS=m CONFIG_FANOTIFY=y @@ -626,12 +617,6 @@ CONFIG_ASYMMETRIC_PUBLIC_KEY_SUBTYPE=m CONFIG_X509_CERTIFICATE_PARSER=m CONFIG_CRC7=m CONFIG_CRC8=m -CONFIG_XZ_DEC_X86=y -CONFIG_XZ_DEC_POWERPC=y -CONFIG_XZ_DEC_IA64=y -CONFIG_XZ_DEC_ARM=y -CONFIG_XZ_DEC_ARMTHUMB=y -CONFIG_XZ_DEC_SPARC=y CONFIG_CORDIC=m CONFIG_CMM=m CONFIG_APPLDATA_BASE=y diff --git a/arch/s390/configs/performance_defconfig b/arch/s390/configs/performance_defconfig index 13559d32af6..822c2f2e0c2 100644 --- a/arch/s390/configs/performance_defconfig +++ b/arch/s390/configs/performance_defconfig @@ -33,7 +33,6 @@ CONFIG_MODULE_UNLOAD=y CONFIG_MODULE_FORCE_UNLOAD=y CONFIG_MODVERSIONS=y CONFIG_MODULE_SRCVERSION_ALL=y -CONFIG_BLK_DEV_INTEGRITY=y CONFIG_BLK_DEV_THROTTLING=y CONFIG_PARTITION_ADVANCED=y CONFIG_IBM_PARTITION=y @@ -241,6 +240,7 @@ CONFIG_NF_TABLES_IPV4=m CONFIG_NFT_CHAIN_ROUTE_IPV4=m CONFIG_NFT_CHAIN_NAT_IPV4=m CONFIG_NF_TABLES_ARP=m +CONFIG_NF_NAT_IPV4=m CONFIG_IP_NF_IPTABLES=m CONFIG_IP_NF_MATCH_AH=m CONFIG_IP_NF_MATCH_ECN=m @@ -248,11 +248,6 @@ CONFIG_IP_NF_MATCH_RPFILTER=m CONFIG_IP_NF_MATCH_TTL=m CONFIG_IP_NF_FILTER=m CONFIG_IP_NF_TARGET_REJECT=m -CONFIG_IP_NF_TARGET_ULOG=m -CONFIG_NF_NAT_IPV4=m -CONFIG_IP_NF_TARGET_MASQUERADE=m -CONFIG_IP_NF_TARGET_NETMAP=m -CONFIG_IP_NF_TARGET_REDIRECT=m CONFIG_IP_NF_MANGLE=m CONFIG_IP_NF_TARGET_CLUSTERIP=m CONFIG_IP_NF_TARGET_ECN=m @@ -266,6 +261,7 @@ CONFIG_NF_CONNTRACK_IPV6=m CONFIG_NF_TABLES_IPV6=m CONFIG_NFT_CHAIN_ROUTE_IPV6=m CONFIG_NFT_CHAIN_NAT_IPV6=m +CONFIG_NF_NAT_IPV6=m CONFIG_IP6_NF_IPTABLES=m CONFIG_IP6_NF_MATCH_AH=m CONFIG_IP6_NF_MATCH_EUI64=m @@ -282,9 +278,6 @@ CONFIG_IP6_NF_TARGET_REJECT=m CONFIG_IP6_NF_MANGLE=m CONFIG_IP6_NF_RAW=m CONFIG_IP6_NF_SECURITY=m -CONFIG_NF_NAT_IPV6=m -CONFIG_IP6_NF_TARGET_MASQUERADE=m -CONFIG_IP6_NF_TARGET_NPT=m CONFIG_NF_TABLES_BRIDGE=m CONFIG_NET_SCTPPROBE=m CONFIG_RDS=m @@ -369,14 +362,13 @@ CONFIG_BLK_DEV_SR=m CONFIG_CHR_DEV_SG=y CONFIG_CHR_DEV_SCH=m CONFIG_SCSI_ENCLOSURE=m -CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_LOGGING=y CONFIG_SCSI_SPI_ATTRS=m +CONFIG_SCSI_FC_ATTRS=y CONFIG_SCSI_SAS_LIBSAS=m CONFIG_SCSI_SRP_ATTRS=m CONFIG_ISCSI_TCP=m -CONFIG_LIBFCOE=m CONFIG_SCSI_DEBUG=m CONFIG_ZFCP=y CONFIG_SCSI_VIRTIO=m @@ -422,7 +414,6 @@ CONFIG_VIRTIO_NET=m CONFIG_NLMON=m CONFIG_VHOST_NET=m # CONFIG_NET_VENDOR_ARC is not set -# CONFIG_NET_CADENCE is not set # CONFIG_NET_VENDOR_CHELSIO is not set # CONFIG_NET_VENDOR_INTEL is not set # CONFIG_NET_VENDOR_MARVELL is not set @@ -476,13 +467,13 @@ CONFIG_JFS_FS=m CONFIG_JFS_POSIX_ACL=y CONFIG_JFS_SECURITY=y CONFIG_JFS_STATISTICS=y -CONFIG_XFS_FS=m +CONFIG_XFS_FS=y CONFIG_XFS_QUOTA=y CONFIG_XFS_POSIX_ACL=y CONFIG_XFS_RT=y CONFIG_GFS2_FS=m CONFIG_OCFS2_FS=m -CONFIG_BTRFS_FS=m +CONFIG_BTRFS_FS=y CONFIG_BTRFS_FS_POSIX_ACL=y CONFIG_NILFS2_FS=m CONFIG_FANOTIFY=y @@ -550,8 +541,11 @@ CONFIG_TIMER_STATS=y CONFIG_RCU_TORTURE_TEST=m CONFIG_RCU_CPU_STALL_TIMEOUT=60 CONFIG_LATENCYTOP=y +CONFIG_SCHED_TRACER=y +CONFIG_FTRACE_SYSCALLS=y +CONFIG_STACK_TRACER=y CONFIG_BLK_DEV_IO_TRACE=y -# CONFIG_KPROBE_EVENT is not set +CONFIG_UPROBE_EVENT=y CONFIG_LKDTM=m CONFIG_PERCPU_TEST=m CONFIG_ATOMIC64_SELFTEST=y @@ -618,12 +612,6 @@ CONFIG_ASYMMETRIC_PUBLIC_KEY_SUBTYPE=m CONFIG_X509_CERTIFICATE_PARSER=m CONFIG_CRC7=m CONFIG_CRC8=m -CONFIG_XZ_DEC_X86=y -CONFIG_XZ_DEC_POWERPC=y -CONFIG_XZ_DEC_IA64=y -CONFIG_XZ_DEC_ARM=y -CONFIG_XZ_DEC_ARMTHUMB=y -CONFIG_XZ_DEC_SPARC=y CONFIG_CORDIC=m CONFIG_CMM=m CONFIG_APPLDATA_BASE=y diff --git a/arch/s390/configs/zfcpdump_defconfig b/arch/s390/configs/zfcpdump_defconfig index e376789f2d8..9d63051ebec 100644 --- a/arch/s390/configs/zfcpdump_defconfig +++ b/arch/s390/configs/zfcpdump_defconfig @@ -22,8 +22,8 @@ CONFIG_HZ_100=y CONFIG_CRASH_DUMP=y # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set # CONFIG_SECCOMP is not set -# CONFIG_IUCV is not set CONFIG_NET=y +# CONFIG_IUCV is not set CONFIG_ATM=y CONFIG_ATM_LANE=y CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" @@ -36,9 +36,9 @@ CONFIG_ENCLOSURE_SERVICES=y CONFIG_SCSI=y CONFIG_BLK_DEV_SD=y CONFIG_SCSI_ENCLOSURE=y -CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_LOGGING=y +CONFIG_SCSI_FC_ATTRS=y CONFIG_SCSI_SRP_ATTRS=y CONFIG_ZFCP=y # CONFIG_INPUT_MOUSEDEV_PSAUX is not set @@ -75,12 +75,6 @@ CONFIG_DEBUG_KERNEL=y CONFIG_RCU_CPU_STALL_TIMEOUT=60 # CONFIG_FTRACE is not set # CONFIG_STRICT_DEVMEM is not set -CONFIG_XZ_DEC_X86=y -CONFIG_XZ_DEC_POWERPC=y -CONFIG_XZ_DEC_IA64=y -CONFIG_XZ_DEC_ARM=y -CONFIG_XZ_DEC_ARMTHUMB=y -CONFIG_XZ_DEC_SPARC=y # CONFIG_PFAULT is not set # CONFIG_S390_HYPFS_FS is not set # CONFIG_VIRTUALIZATION is not set diff --git a/arch/s390/defconfig b/arch/s390/defconfig index fab35a8efa4..785c5f24d6f 100644 --- a/arch/s390/defconfig +++ b/arch/s390/defconfig @@ -92,10 +92,10 @@ CONFIG_CHR_DEV_ST=y CONFIG_BLK_DEV_SR=y CONFIG_BLK_DEV_SR_VENDOR=y CONFIG_CHR_DEV_SG=y -CONFIG_SCSI_MULTI_LUN=y CONFIG_SCSI_CONSTANTS=y CONFIG_SCSI_LOGGING=y CONFIG_SCSI_SCAN_ASYNC=y +CONFIG_SCSI_FC_ATTRS=y CONFIG_ZFCP=y CONFIG_SCSI_VIRTIO=y CONFIG_NETDEVICES=y @@ -164,14 +164,13 @@ CONFIG_CRYPTO_CMAC=m CONFIG_CRYPTO_XCBC=m CONFIG_CRYPTO_VMAC=m CONFIG_CRYPTO_CRC32=m -CONFIG_CRYPTO_CRCT10DIF=m CONFIG_CRYPTO_MD4=m CONFIG_CRYPTO_MICHAEL_MIC=m CONFIG_CRYPTO_RMD128=m CONFIG_CRYPTO_RMD160=m CONFIG_CRYPTO_RMD256=m CONFIG_CRYPTO_RMD320=m -CONFIG_CRYPTO_SHA256=m +CONFIG_CRYPTO_SHA256=y CONFIG_CRYPTO_SHA512=m CONFIG_CRYPTO_TGR192=m CONFIG_CRYPTO_WP512=m -- cgit v1.2.3-70-g09d2 From 49dc71268bec9a6a28107ba64d834460e1513909 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 27 Oct 2014 09:00:21 -0700 Subject: ARM: omap2plus_defconfig: Fix bloat caused by having ipv6 built-in Commit 673ce00c5d6c (ARM: omap2plus_defconfig: Add support for distros with systemd) caused considerable bloat as noted by Paul Walmsley . Let's fix this issue by making what we can into loadable modules for the systemd options. That's only IPV6 and AUTOFS4_FS it seems, and IPv6 defaults to a loadable module. Reported-by: Paul Walmsley Signed-off-by: Tony Lindgren --- arch/arm/configs/omap2plus_defconfig | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index 16e719c268d..3fbad5b9561 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -86,7 +86,6 @@ CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y CONFIG_IP_PNP_RARP=y # CONFIG_INET_LRO is not set -CONFIG_IPV6=y CONFIG_NETFILTER=y CONFIG_CAN=m CONFIG_CAN_C_CAN=m @@ -317,7 +316,7 @@ CONFIG_EXT4_FS=y CONFIG_FANOTIFY=y CONFIG_QUOTA=y CONFIG_QFMT_V2=y -CONFIG_AUTOFS4_FS=y +CONFIG_AUTOFS4_FS=m CONFIG_MSDOS_FS=y CONFIG_VFAT_FS=y CONFIG_TMPFS=y -- cgit v1.2.3-70-g09d2 From b1bde689dde0d5de9e974390f9a0859a7ec5fd1b Mon Sep 17 00:00:00 2001 From: Aaron Lu Date: Thu, 23 Oct 2014 16:18:02 +0800 Subject: toshiba_acpi: Add Toshiba TECRA A50-A to the alt keymap dmi list As bug #72551, the Toshiba TECRA A50-A series models also come with the new keymap layout as found out by Azael Avalos, so add it to the dmi table. Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=76971 Reported-and-tested-by: Blindekinder Cc: Azael Avalos Signed-off-by: Aaron Lu Signed-off-by: Darren Hart --- drivers/platform/x86/toshiba_acpi.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/platform/x86/toshiba_acpi.c b/drivers/platform/x86/toshiba_acpi.c index ef3a1904e92..ab6151f0542 100644 --- a/drivers/platform/x86/toshiba_acpi.c +++ b/drivers/platform/x86/toshiba_acpi.c @@ -240,6 +240,12 @@ static const struct dmi_system_id toshiba_alt_keymap_dmi[] = { DMI_MATCH(DMI_PRODUCT_NAME, "Qosmio X75-A"), }, }, + { + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"), + DMI_MATCH(DMI_PRODUCT_NAME, "TECRA A50-A"), + }, + }, {} }; -- cgit v1.2.3-70-g09d2 From 4ec7a45b51a32ee513898e2f1e42bb681b340fcf Mon Sep 17 00:00:00 2001 From: Stanislaw Gruszka Date: Sun, 26 Oct 2014 11:23:55 +0100 Subject: asus-nb-wmi: Add wapf4 quirk for the X550VB X550VB as many others Asus laptops need wapf4 quirk to make RFKILL switch be functional. Otherwise system boots with wireless card disabled and is only possible to enable it by suspend/resume. Bug report: http://bugzilla.redhat.com/show_bug.cgi?id=1089731#c23 Reported-and-tested-by: Vratislav Podzimek Signed-off-by: Stanislaw Gruszka Signed-off-by: Darren Hart --- drivers/platform/x86/asus-nb-wmi.c | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/drivers/platform/x86/asus-nb-wmi.c b/drivers/platform/x86/asus-nb-wmi.c index 3a4951f4606..c1a6cd66af4 100644 --- a/drivers/platform/x86/asus-nb-wmi.c +++ b/drivers/platform/x86/asus-nb-wmi.c @@ -180,6 +180,15 @@ static const struct dmi_system_id asus_quirks[] = { }, .driver_data = &quirk_asus_wapf4, }, + { + .callback = dmi_matched, + .ident = "ASUSTeK COMPUTER INC. X550VB", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."), + DMI_MATCH(DMI_PRODUCT_NAME, "X550VB"), + }, + .driver_data = &quirk_asus_wapf4, + }, { .callback = dmi_matched, .ident = "ASUSTeK COMPUTER INC. X55A", -- cgit v1.2.3-70-g09d2 From 5a1426c99f9b7aa11d60c4e6b7a3211bb5321696 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Wed, 22 Oct 2014 16:06:37 +0200 Subject: samsung-laptop: Add broken-acpi-video quirk for NC210/NC110 The acpi-video backlight interface on the NC210 does not work, blacklist it and use the samsung-laptop interface instead. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=861573 Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede Signed-off-by: Darren Hart --- drivers/platform/x86/samsung-laptop.c | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/drivers/platform/x86/samsung-laptop.c b/drivers/platform/x86/samsung-laptop.c index 5a596651227..ff765d8e1a0 100644 --- a/drivers/platform/x86/samsung-laptop.c +++ b/drivers/platform/x86/samsung-laptop.c @@ -1559,6 +1559,16 @@ static struct dmi_system_id __initdata samsung_dmi_table[] = { }, .driver_data = &samsung_broken_acpi_video, }, + { + .callback = samsung_dmi_matched, + .ident = "NC210", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "SAMSUNG ELECTRONICS CO., LTD."), + DMI_MATCH(DMI_PRODUCT_NAME, "NC210/NC110"), + DMI_MATCH(DMI_BOARD_NAME, "NC210/NC110"), + }, + .driver_data = &samsung_broken_acpi_video, + }, { .callback = samsung_dmi_matched, .ident = "730U3E/740U3E", -- cgit v1.2.3-70-g09d2 From 183fd8fcd7f8afb7ac5ec68f83194872f9fecc84 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Wed, 22 Oct 2014 16:06:38 +0200 Subject: acer-wmi: Add acpi_backlight=video quirk for the Acer KAV80 The acpi-video backlight interface on the Acer KAV80 is broken, and worse it causes the entire machine to slow down significantly after a suspend/resume. Blacklist it, and use the acer-wmi backlight interface instead. Note that the KAV80 is somewhat unique in that it is the only Acer model where we fall back to acer-wmi after blacklisting, rather then using the native (e.g. intel) backlight driver. This is done because there is no native backlight interface on this model. BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1128309 Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede Signed-off-by: Darren Hart --- drivers/platform/x86/acer-wmi.c | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/drivers/platform/x86/acer-wmi.c b/drivers/platform/x86/acer-wmi.c index 96a0b75c52c..26c4fd1394d 100644 --- a/drivers/platform/x86/acer-wmi.c +++ b/drivers/platform/x86/acer-wmi.c @@ -579,6 +579,17 @@ static const struct dmi_system_id video_vendor_dmi_table[] __initconst = { DMI_MATCH(DMI_PRODUCT_NAME, "Aspire 5741"), }, }, + { + /* + * Note no video_set_backlight_video_vendor, we must use the + * acer interface, as there is no native backlight interface. + */ + .ident = "Acer KAV80", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "Acer"), + DMI_MATCH(DMI_PRODUCT_NAME, "KAV80"), + }, + }, {} }; -- cgit v1.2.3-70-g09d2 From 725c7f619e20f5051bba627fca11dc107c2a93b1 Mon Sep 17 00:00:00 2001 From: Stephan Mueller Date: Mon, 27 Oct 2014 04:09:50 +0100 Subject: quirk for Lenovo Yoga 3: no rfkill switch The Yoga 3 does not contain any physical rfkill switch. Therefore disable the rfkill switch identically to the Yoga 2 approach. Signed-off-by: Stephan Mueller Signed-off-by: Darren Hart --- drivers/platform/x86/ideapad-laptop.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/platform/x86/ideapad-laptop.c b/drivers/platform/x86/ideapad-laptop.c index 02152de135b..ed494f37c40 100644 --- a/drivers/platform/x86/ideapad-laptop.c +++ b/drivers/platform/x86/ideapad-laptop.c @@ -837,6 +837,13 @@ static const struct dmi_system_id no_hw_rfkill_list[] = { DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo Yoga 2"), }, }, + { + .ident = "Lenovo Yoga 3 Pro 1370", + .matches = { + DMI_MATCH(DMI_SYS_VENDOR, "LENOVO"), + DMI_MATCH(DMI_PRODUCT_VERSION, "Lenovo YOGA 3 Pro-1370"), + }, + }, {} }; -- cgit v1.2.3-70-g09d2 From 6ed15ea67b5ebb13ececcfc6056d90a70ed96f7b Mon Sep 17 00:00:00 2001 From: Heiko Carstens Date: Mon, 27 Oct 2014 15:49:06 +0100 Subject: s390/ftrace: add ftrace_graph_is_dead() check Add an ftrace_graph_is_dead() check to prepare_ftrace_return() in order to detect an internal ftrace graph error. This allows to prevent further ftrace graph handling and hopefully keeps the kernel alive. This patch is the same like for all other architectures. For unkown reasons s390 was left out. Signed-off-by: Heiko Carstens Signed-off-by: Martin Schwidefsky --- arch/s390/kernel/ftrace.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/s390/kernel/ftrace.c b/arch/s390/kernel/ftrace.c index 51d14fe5eb9..ca1cabb3a96 100644 --- a/arch/s390/kernel/ftrace.c +++ b/arch/s390/kernel/ftrace.c @@ -121,6 +121,8 @@ unsigned long __kprobes prepare_ftrace_return(unsigned long parent, { struct ftrace_graph_ent trace; + if (unlikely(ftrace_graph_is_dead())) + goto out; if (unlikely(atomic_read(¤t->tracing_graph_pause))) goto out; ip = (ip & PSW_ADDR_INSN) - MCOUNT_INSN_SIZE; -- cgit v1.2.3-70-g09d2 From d90c33818967c5e5371961604ad98b4dea4fa3f4 Mon Sep 17 00:00:00 2001 From: David Cohen Date: Tue, 14 Oct 2014 10:54:37 -0700 Subject: pinctrl: baytrail: show output gpio state correctly on Intel Baytrail Even if a gpio pin is set to output, we still need to set INPUT_EN functionality (by clearing INPUT_EN bit) to be able to read the pin's level. E.g. without this change, we'll always read low level state from sysfs. Cc: # v3.14+ Cc: Mathias Nyman Signed-off-by: David Cohen Reviewed-by: Felipe Balbi Signed-off-by: Linus Walleij --- drivers/pinctrl/pinctrl-baytrail.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/pinctrl/pinctrl-baytrail.c b/drivers/pinctrl/pinctrl-baytrail.c index b83ec87c71f..9dc38140194 100644 --- a/drivers/pinctrl/pinctrl-baytrail.c +++ b/drivers/pinctrl/pinctrl-baytrail.c @@ -322,7 +322,7 @@ static int byt_gpio_direction_output(struct gpio_chip *chip, "Potential Error: Setting GPIO with direct_irq_en to output"); reg_val = readl(reg) | BYT_DIR_MASK; - reg_val &= ~BYT_OUTPUT_EN; + reg_val &= ~(BYT_OUTPUT_EN | BYT_INPUT_EN); if (value) writel(reg_val | BYT_LEVEL, reg); -- cgit v1.2.3-70-g09d2 From 9599815de61db104ad21bc61f5e3544d2415c6ee Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Mon, 20 Oct 2014 12:45:32 +0200 Subject: usb: dwc2: gadget: fix enumeration issues Excessive debug messages might cause timing issues that prevent correct usb enumeration. This patch hides information about USB bus reset to let driver enumerate fast enough to avoid making host angry. This fixes endless enumeration and usb reset loop observed with some Linux hosts. Acked-by: Paul Zimmerman Signed-off-by: Marek Szyprowski Reviewed-by: Felipe Balbi Signed-off-by: Felipe Balbi --- drivers/usb/dwc2/gadget.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/dwc2/gadget.c b/drivers/usb/dwc2/gadget.c index eee87098bb8..8b5c079c7b7 100644 --- a/drivers/usb/dwc2/gadget.c +++ b/drivers/usb/dwc2/gadget.c @@ -2327,7 +2327,7 @@ irq_retry: u32 usb_status = readl(hsotg->regs + GOTGCTL); - dev_info(hsotg->dev, "%s: USBRst\n", __func__); + dev_dbg(hsotg->dev, "%s: USBRst\n", __func__); dev_dbg(hsotg->dev, "GNPTXSTS=%08x\n", readl(hsotg->regs + GNPTXSTS)); -- cgit v1.2.3-70-g09d2 From f0fd9ad87e698d634ab5894f751b7af908e96a41 Mon Sep 17 00:00:00 2001 From: Soren Brinkmann Date: Thu, 23 Oct 2014 09:29:22 -0700 Subject: MAINTAINERS: Add Soren as reviewer for Zynq Signed-off-by: Soren Brinkmann Acked-by: Michal Simek Signed-off-by: Arnd Bergmann --- MAINTAINERS | 1 + 1 file changed, 1 insertion(+) diff --git a/MAINTAINERS b/MAINTAINERS index 71fdbd4f4ac..7b765a42e2d 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1543,6 +1543,7 @@ F: arch/arm/mach-pxa/include/mach/z2.h ARM/ZYNQ ARCHITECTURE M: Michal Simek +R: Sören Brinkmann L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers) W: http://wiki.xilinx.com T: git git://git.xilinx.com/linux-xlnx.git -- cgit v1.2.3-70-g09d2 From f267ea0fe05123e8101e5793d977b537924939a0 Mon Sep 17 00:00:00 2001 From: Stefan Hengelein Date: Sun, 19 Oct 2014 19:49:45 +0200 Subject: ARM: ixp4xx: remove compilation warnings in io.h When arch/arm/mach-ixp4xx/common-pci.c is compiled, two warnings occur: arch/arm/mach-ixp4xx/include/mach/io.h:144: warning: passing argument 1 of '__raw_readb' makes pointer from integer without a cast arch/arm/mach-ixp4xx/include/mach/io.h:79: warning: passing argument 2 of '__raw_writeb' makes pointer from integer without a cast Both functions expect an 'volatile void __iomem *' but get an u32. The 'u32 addr' variable is initialized with the address of an 'volatile void __iomem *' pointer. Passing the pointer directly, avoids the warning and semantics are preserved. This warning was found with vampyr. Signed-off-by: Stefan Hengelein Signed-off-by: Arnd Bergmann --- arch/arm/mach-ixp4xx/include/mach/io.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h index 559c69a4773..7d11979da03 100644 --- a/arch/arm/mach-ixp4xx/include/mach/io.h +++ b/arch/arm/mach-ixp4xx/include/mach/io.h @@ -76,7 +76,7 @@ static inline void __indirect_writeb(u8 value, volatile void __iomem *p) u32 n, byte_enables, data; if (!is_pci_memory(addr)) { - __raw_writeb(value, addr); + __raw_writeb(value, p); return; } @@ -141,7 +141,7 @@ static inline unsigned char __indirect_readb(const volatile void __iomem *p) u32 n, byte_enables, data; if (!is_pci_memory(addr)) - return __raw_readb(addr); + return __raw_readb(p); n = addr % 4; byte_enables = (0xf & ~BIT(n)) << IXP4XX_PCI_NP_CBE_BESL; -- cgit v1.2.3-70-g09d2 From 157a1b17a5eb24f957ada8c2522cb88d9e3665fb Mon Sep 17 00:00:00 2001 From: Axel Lin Date: Sun, 19 Oct 2014 23:41:00 +0800 Subject: soc: versatile: Add terminating entry for realview_soc_of_match The of_device_id table is supposed to be zero-terminated. Signed-off-by: Axel Lin Acked-by: Linus Walleij Signed-off-by: Arnd Bergmann --- drivers/soc/versatile/soc-realview.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/soc/versatile/soc-realview.c b/drivers/soc/versatile/soc-realview.c index cea8ea3491d..1a07bf540fe 100644 --- a/drivers/soc/versatile/soc-realview.c +++ b/drivers/soc/versatile/soc-realview.c @@ -26,6 +26,7 @@ static const struct of_device_id realview_soc_of_match[] = { { .compatible = "arm,realview-pb11mp-soc", }, { .compatible = "arm,realview-pba8-soc", }, { .compatible = "arm,realview-pbx-soc", }, + { } }; static u32 realview_coreid; -- cgit v1.2.3-70-g09d2 From d6093099698962a4564d50cb7d389068ecea3dbc Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Tue, 21 Oct 2014 19:55:20 +0100 Subject: ARM: multi_v7_defconfig: fix support for APQ8084 This patch enables configs required to boot IFC6540 board with atleast a serial console. Without this patch there is no serial console. Signed-off-by: Srinivas Kandagatla Signed-off-by: Arnd Bergmann --- arch/arm/configs/multi_v7_defconfig | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig index 709ecc9009e..2fab4f6cc6e 100644 --- a/arch/arm/configs/multi_v7_defconfig +++ b/arch/arm/configs/multi_v7_defconfig @@ -235,6 +235,7 @@ CONFIG_SPI_TEGRA20_SLINK=y CONFIG_SPI_XILINX=y CONFIG_PINCTRL_AS3722=y CONFIG_PINCTRL_PALMAS=y +CONFIG_PINCTRL_APQ8084=y CONFIG_GPIO_SYSFS=y CONFIG_GPIO_GENERIC_PLATFORM=y CONFIG_GPIO_DWAPB=y @@ -410,6 +411,7 @@ CONFIG_NVEC_POWER=y CONFIG_NVEC_PAZ00=y CONFIG_QCOM_GSBI=y CONFIG_COMMON_CLK_QCOM=y +CONFIG_APQ_MMCC_8084=y CONFIG_MSM_GCC_8660=y CONFIG_MSM_MMCC_8960=y CONFIG_MSM_MMCC_8974=y -- cgit v1.2.3-70-g09d2 From a6bbce54efa9145dbcf3029c885549f7ebc40a3b Mon Sep 17 00:00:00 2001 From: Dave Chinner Date: Wed, 29 Oct 2014 08:22:18 +1100 Subject: xfs: bulkstat doesn't release AGI buffer on error The recent refactoring of the bulkstat code left a small landmine in the code. If a inobt read fails, then the tree walk is aborted and returns without releasing the AGI buffer or freeing the cursor. This can lead to a subsequent bulkstat call hanging trying to grab the AGI buffer again. cc: Signed-off-by: Dave Chinner Reviewed-by: Brian Foster Reviewed-by: Eric Sandeen Signed-off-by: Dave Chinner --- fs/xfs/xfs_itable.c | 16 ++++++++++------ 1 file changed, 10 insertions(+), 6 deletions(-) diff --git a/fs/xfs/xfs_itable.c b/fs/xfs/xfs_itable.c index f1deb961a29..ef8ea058978 100644 --- a/fs/xfs/xfs_itable.c +++ b/fs/xfs/xfs_itable.c @@ -427,7 +427,7 @@ xfs_bulkstat( error = xfs_bulkstat_grab_ichunk(cur, agino, &icount, &r); if (error) - break; + goto del_cursor; if (icount) { irbp->ir_startino = r.ir_startino; irbp->ir_freecount = r.ir_freecount; @@ -442,7 +442,7 @@ xfs_bulkstat( error = xfs_inobt_lookup(cur, 0, XFS_LOOKUP_GE, &tmp); } if (error) - break; + goto del_cursor; /* * Loop through inode btree records in this ag, @@ -454,7 +454,7 @@ xfs_bulkstat( error = xfs_inobt_get_rec(cur, &r, &i); if (error || i == 0) { end_of_ag = 1; - break; + goto del_cursor; } /* @@ -476,13 +476,17 @@ xfs_bulkstat( error = xfs_btree_increment(cur, 0, &tmp); cond_resched(); } + /* - * Drop the btree buffers and the agi buffer. - * We can't hold any of the locks these represent - * when calling iget. + * Drop the btree buffers and the agi buffer as we can't hold any + * of the locks these represent when calling iget. If there is a + * pending error, then we are done. */ +del_cursor: xfs_btree_del_cursor(cur, XFS_BTREE_NOERROR); xfs_buf_relse(agbp); + if (error) + break; /* * Now format all the good inodes into the user's buffer. */ -- cgit v1.2.3-70-g09d2 From 30fa0530ff87f6379e046629adfa3f4872a2d353 Mon Sep 17 00:00:00 2001 From: Zubair Lutfullah Kakakhel Date: Tue, 28 Oct 2014 11:28:34 +0000 Subject: MIPS: CMA: Do not reserve memory if not required Even if CMA is disabled, the for_each_memblock macro expands to run reserve_bootmem once. Hence, reserve_bootmem attempts to reserve location 0 of size 0. Add a check to avoid that. Issue was highlighted during testing with EVA enabled. resrve_bootmem used to exit gracefully when passed arguments to reserve 0 size location at 0 without EVA. But with EVA enabled, macros would point to different addresses and the code would trigger a BUG. Signed-off-by: Zubair Lutfullah Kakakhel Tested-by: Markos Chandras Tested-by: Huacai Chen Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/8231/ Signed-off-by: Ralf Baechle --- arch/mips/kernel/setup.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/mips/kernel/setup.c b/arch/mips/kernel/setup.c index b3b8f0d9d4a..d21ec57b6e9 100644 --- a/arch/mips/kernel/setup.c +++ b/arch/mips/kernel/setup.c @@ -683,7 +683,8 @@ static void __init arch_mem_init(char **cmdline_p) dma_contiguous_reserve(PFN_PHYS(max_low_pfn)); /* Tell bootmem about cma reserved memblock section */ for_each_memblock(reserved, reg) - reserve_bootmem(reg->base, reg->size, BOOTMEM_DEFAULT); + if (reg->size != 0) + reserve_bootmem(reg->base, reg->size, BOOTMEM_DEFAULT); } static void __init resource_init(void) -- cgit v1.2.3-70-g09d2 From 7de79a1d4992921c85b10077520385acc5b9a6e0 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Wed, 8 Oct 2014 23:08:13 +0100 Subject: regulator: of: Lower the severity of the error with no container Description of regulators should generally be optional so if there is no DT node for the regulators container then we shouldn't print an error message. Lower the severity of the message to debug level (it might help someone work out what went wrong) and while we're at it say what we were looking for. Reported-by: Guenter Roeck Signed-off-by: Mark Brown --- drivers/regulator/of_regulator.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c index 7a51814abdc..5a1d4afa477 100644 --- a/drivers/regulator/of_regulator.c +++ b/drivers/regulator/of_regulator.c @@ -211,7 +211,8 @@ struct regulator_init_data *regulator_of_get_init_data(struct device *dev, search = dev->of_node; if (!search) { - dev_err(dev, "Failed to find regulator container node\n"); + dev_dbg(dev, "Failed to find regulator container node '%s'\n", + desc->regulators_node); return NULL; } -- cgit v1.2.3-70-g09d2 From 739fd5078493f9ea96b7562f504fcc1316d13164 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 27 Oct 2014 13:06:07 -0700 Subject: ARM: omap2plus_defconfig: Fix errors with NAND BCH Looks like we need to have BCH enabled to get NAND working and to avoid getting: nand: error: CONFIG_MTD_NAND_ECC_BCH not enabled Signed-off-by: Tony Lindgren --- arch/arm/configs/omap2plus_defconfig | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig index 3fbad5b9561..b3f86670d2e 100644 --- a/arch/arm/configs/omap2plus_defconfig +++ b/arch/arm/configs/omap2plus_defconfig @@ -111,6 +111,7 @@ CONFIG_MTD_OOPS=y CONFIG_MTD_CFI=y CONFIG_MTD_CFI_INTELEXT=y CONFIG_MTD_NAND=y +CONFIG_MTD_NAND_ECC_BCH=y CONFIG_MTD_NAND_OMAP2=y CONFIG_MTD_ONENAND=y CONFIG_MTD_ONENAND_VERIFY_WRITE=y -- cgit v1.2.3-70-g09d2 From 4b91f7f3c8b20e073b7bfc098625b37f99789508 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Mon, 27 Oct 2014 13:05:54 -0700 Subject: ARM: OMAP2+: Warn about deprecated legacy booting mode We're moving omaps to use device tree based booting and already have omap2, omap4, omap5, am335x and am437x booting in device tree only mode. Only omap3 still has legacy booting still around and we really want to make that device tree only. So let's add a warning about deprecated legacy booting so we get people to upgrade their boards to use device tree based booting and find out about any remaining issues. Note that for most boards we already have the .dts file and those can be booted with without changing the bootloader using the appended DTB mode. Acked-By: Sebastian Reichel Reviewed-by: Aaro Koskinen Reviewed-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/omap_device.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/mach-omap2/omap_device.c b/arch/arm/mach-omap2/omap_device.c index d22c30d3ccf..8c58b71c272 100644 --- a/arch/arm/mach-omap2/omap_device.c +++ b/arch/arm/mach-omap2/omap_device.c @@ -917,6 +917,10 @@ static int __init omap_device_late_idle(struct device *dev, void *data) static int __init omap_device_late_init(void) { bus_for_each_dev(&platform_bus_type, NULL, NULL, omap_device_late_idle); + + WARN(!of_have_populated_dt(), + "legacy booting deprecated, please update to boot with .dts\n"); + return 0; } omap_late_initcall_sync(omap_device_late_init); -- cgit v1.2.3-70-g09d2 From 7a19dee116c8fae7ba7a778043c245194289f5a2 Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Thu, 30 Oct 2014 10:34:52 +1100 Subject: xfs: Check error during inode btree iteration in xfs_bulkstat() xfs_bulkstat() doesn't check error return from xfs_btree_increment(). In case of specific fs corruption that could result in xfs_bulkstat() entering an infinite loop because we would be looping over the same chunk over and over again. Fix the problem by checking the return value and terminating the loop properly. Coverity-id: 1231338 cc: Signed-off-by: Jan Kara Reviewed-by: Jie Liu Signed-off-by: Dave Chinner --- fs/xfs/xfs_itable.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/fs/xfs/xfs_itable.c b/fs/xfs/xfs_itable.c index ef8ea058978..7765ff743e9 100644 --- a/fs/xfs/xfs_itable.c +++ b/fs/xfs/xfs_itable.c @@ -474,6 +474,10 @@ xfs_bulkstat( */ agino = r.ir_startino + XFS_INODES_PER_CHUNK; error = xfs_btree_increment(cur, 0, &tmp); + if (error) { + end_of_ag = 1; + goto del_cursor; + } cond_resched(); } -- cgit v1.2.3-70-g09d2 From f55fefd1a5a339b1bd08c120b93312d6eb64a9fb Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Thu, 30 Oct 2014 10:35:00 +1100 Subject: mm: Remove false WARN_ON from pagecache_isize_extended() The WARN_ON checking whether i_mutex is held in pagecache_isize_extended() was wrong because some filesystems (e.g. XFS) use different locks for serialization of truncates / writes. So just remove the check. Signed-off-by: Jan Kara Reviewed-by: Dave Chinner Signed-off-by: Dave Chinner --- mm/truncate.c | 1 - 1 file changed, 1 deletion(-) diff --git a/mm/truncate.c b/mm/truncate.c index 261eaf6e5a1..c646084e5ee 100644 --- a/mm/truncate.c +++ b/mm/truncate.c @@ -755,7 +755,6 @@ void pagecache_isize_extended(struct inode *inode, loff_t from, loff_t to) struct page *page; pgoff_t index; - WARN_ON(!mutex_is_locked(&inode->i_mutex)); WARN_ON(to > inode->i_size); if (from >= to || bsize == PAGE_CACHE_SIZE) -- cgit v1.2.3-70-g09d2 From 5d11fb4b9a1d90983452c029b5e1377af78fda49 Mon Sep 17 00:00:00 2001 From: Brian Foster Date: Thu, 30 Oct 2014 10:35:11 +1100 Subject: xfs: rework zero range to prevent invalid i_size updates The zero range operation is analogous to fallocate with the exception of converting the range to zeroes. E.g., it attempts to allocate zeroed blocks over the range specified by the caller. The XFS implementation kills all delalloc blocks currently over the aligned range, converts the range to allocated zero blocks (unwritten extents) and handles the partial pages at the ends of the range by sending writes through the pagecache. The current implementation suffers from several problems associated with inode size. If the aligned range covers an extending I/O, said I/O is discarded and an inode size update from a previous write never makes it to disk. Further, if an unaligned zero range extends beyond eof, the page write induced for the partial end page can itself increase the inode size, even if the zero range request is not supposed to update i_size (via KEEP_SIZE, similar to an fallocate beyond EOF). The latter behavior not only incorrectly increases the inode size, but can lead to stray delalloc blocks on the inode. Typically, post-eof preallocation blocks are either truncated on release or inode eviction or explicitly written to by xfs_zero_eof() on natural file size extension. If the inode size increases due to zero range, however, associated blocks leak into the address space having never been converted or mapped to pagecache pages. A direct I/O to such an uncovered range cannot convert the extent via writeback and will BUG(). For example: $ xfs_io -fc "pwrite 0 128k" -c "fzero -k 1m 54321" ... $ xfs_io -d -c "pread 128k 128k" If the entire delalloc extent happens to not have page coverage whatsoever (e.g., delalloc conversion couldn't find a large enough free space extent), even a full file writeback won't convert what's left of the extent and we'll assert on inode eviction. Rework xfs_zero_file_space() to avoid buffered I/O for partial pages. Use the existing hole punch and prealloc mechanisms as primitives for zero range. This implementation is not efficient nor ideal as we writeback dirty data over the range and remove existing extents rather than convert to unwrittern. The former writeback, however, is currently the only mechanism available to ensure consistency between pagecache and extent state. Even a pagecache truncate/delalloc punch prior to hole punch has lead to inconsistencies due to racing with writeback. This provides a consistent, correct implementation of zero range that survives fsstress/fsx testing without assert failures. The implementation can be optimized from this point forward once the fundamental issue of pagecache and delalloc extent state consistency is addressed. Signed-off-by: Brian Foster Reviewed-by: Dave Chinner Signed-off-by: Dave Chinner --- fs/xfs/xfs_bmap_util.c | 72 ++++++++++++++------------------------------------ 1 file changed, 20 insertions(+), 52 deletions(-) diff --git a/fs/xfs/xfs_bmap_util.c b/fs/xfs/xfs_bmap_util.c index 92e8f99a585..281002689d6 100644 --- a/fs/xfs/xfs_bmap_util.c +++ b/fs/xfs/xfs_bmap_util.c @@ -1338,7 +1338,10 @@ xfs_free_file_space( goto out; } - +/* + * Preallocate and zero a range of a file. This mechanism has the allocation + * semantics of fallocate and in addition converts data in the range to zeroes. + */ int xfs_zero_file_space( struct xfs_inode *ip, @@ -1346,65 +1349,30 @@ xfs_zero_file_space( xfs_off_t len) { struct xfs_mount *mp = ip->i_mount; - uint granularity; - xfs_off_t start_boundary; - xfs_off_t end_boundary; + uint blksize; int error; trace_xfs_zero_file_space(ip); - granularity = max_t(uint, 1 << mp->m_sb.sb_blocklog, PAGE_CACHE_SIZE); + blksize = 1 << mp->m_sb.sb_blocklog; /* - * Round the range of extents we are going to convert inwards. If the - * offset is aligned, then it doesn't get changed so we zero from the - * start of the block offset points to. + * Punch a hole and prealloc the range. We use hole punch rather than + * unwritten extent conversion for two reasons: + * + * 1.) Hole punch handles partial block zeroing for us. + * + * 2.) If prealloc returns ENOSPC, the file range is still zero-valued + * by virtue of the hole punch. */ - start_boundary = round_up(offset, granularity); - end_boundary = round_down(offset + len, granularity); - - ASSERT(start_boundary >= offset); - ASSERT(end_boundary <= offset + len); - - if (start_boundary < end_boundary - 1) { - /* - * Writeback the range to ensure any inode size updates due to - * appending writes make it to disk (otherwise we could just - * punch out the delalloc blocks). - */ - error = filemap_write_and_wait_range(VFS_I(ip)->i_mapping, - start_boundary, end_boundary - 1); - if (error) - goto out; - truncate_pagecache_range(VFS_I(ip), start_boundary, - end_boundary - 1); - - /* convert the blocks */ - error = xfs_alloc_file_space(ip, start_boundary, - end_boundary - start_boundary - 1, - XFS_BMAPI_PREALLOC | XFS_BMAPI_CONVERT); - if (error) - goto out; - - /* We've handled the interior of the range, now for the edges */ - if (start_boundary != offset) { - error = xfs_iozero(ip, offset, start_boundary - offset); - if (error) - goto out; - } - - if (end_boundary != offset + len) - error = xfs_iozero(ip, end_boundary, - offset + len - end_boundary); - - } else { - /* - * It's either a sub-granularity range or the range spanned lies - * partially across two adjacent blocks. - */ - error = xfs_iozero(ip, offset, len); - } + error = xfs_free_file_space(ip, offset, len); + if (error) + goto out; + error = xfs_alloc_file_space(ip, round_down(offset, blksize), + round_up(offset + len, blksize) - + round_down(offset, blksize), + XFS_BMAPI_PREALLOC); out: return error; -- cgit v1.2.3-70-g09d2 From 94966b712c6875939fcdd83cb2707a797e131a43 Mon Sep 17 00:00:00 2001 From: Fabian Frederick Date: Wed, 29 Oct 2014 21:14:27 +0100 Subject: powerpc: Fix section mismatch warning Add __init to MMU_setup() which uses __initdata boot_command_line. Also MMU_setup() is only called from MMU_init(), which is also __init. Warning appeared since commit 3e47d1474c2b. Fixes: 3e47d1474c2b ("powerpc: Remove powerpc specific cmd_line") Signed-off-by: Fabian Frederick [mpe: Update changelog] Signed-off-by: Michael Ellerman --- arch/powerpc/mm/init_32.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/powerpc/mm/init_32.c b/arch/powerpc/mm/init_32.c index cad68ff8eca..415a51b028b 100644 --- a/arch/powerpc/mm/init_32.c +++ b/arch/powerpc/mm/init_32.c @@ -103,7 +103,7 @@ unsigned long __max_low_memory = MAX_LOW_MEM; /* * Check for command-line options that affect what MMU_init will do. */ -void MMU_setup(void) +void __init MMU_setup(void) { /* Check for nobats option (used in mapin_ram). */ if (strstr(boot_command_line, "nobats")) { -- cgit v1.2.3-70-g09d2 From 408cddd96e3b155337f9e3aba2198e92e94c6068 Mon Sep 17 00:00:00 2001 From: Hari Bathini Date: Wed, 1 Oct 2014 12:32:30 +0530 Subject: powerpc/fadump: Fix endianess issues in firmware assisted dump handling Firmware-assisted dump (fadump) kernel code is not endian safe. The below patch fixes this issue. Tested this patch with upstream kernel. Below output shows crash tool successfully opening LE fadump vmcore. # crash vmlinux vmcore GNU gdb (GDB) 7.6 This GDB was configured as "powerpc64le-unknown-linux-gnu"... KERNEL: vmlinux DUMPFILE: vmcore CPUS: 16 DATE: Wed Dec 31 19:00:00 1969 UPTIME: 00:03:28 LOAD AVERAGE: 0.46, 0.86, 0.41 TASKS: 268 NODENAME: linux-dhr2 RELEASE: 3.17.0-rc5-7-default VERSION: #6 SMP Tue Sep 30 01:06:34 EDT 2014 MACHINE: ppc64le (4116 Mhz) MEMORY: 40 GB PANIC: "Oops: Kernel access of bad area, sig: 11 [#1]" (check log for details) PID: 6223 COMMAND: "bash" TASK: c0000009661b2500 [THREAD_INFO: c000000967ac0000] CPU: 2 STATE: TASK_RUNNING (PANIC) Signed-off-by: Hari Bathini [mpe: Make the comment in pSeries_lpar_hptab_clear() clearer] Signed-off-by: Michael Ellerman --- arch/powerpc/include/asm/fadump.h | 52 ++++++++-------- arch/powerpc/kernel/fadump.c | 114 +++++++++++++++++----------------- arch/powerpc/platforms/pseries/lpar.c | 14 ++++- 3 files changed, 95 insertions(+), 85 deletions(-) diff --git a/arch/powerpc/include/asm/fadump.h b/arch/powerpc/include/asm/fadump.h index a6774560afe..493e72f64b3 100644 --- a/arch/powerpc/include/asm/fadump.h +++ b/arch/powerpc/include/asm/fadump.h @@ -70,39 +70,39 @@ #define CPU_UNKNOWN (~((u32)0)) /* Utility macros */ -#define SKIP_TO_NEXT_CPU(reg_entry) \ -({ \ - while (reg_entry->reg_id != REG_ID("CPUEND")) \ - reg_entry++; \ - reg_entry++; \ +#define SKIP_TO_NEXT_CPU(reg_entry) \ +({ \ + while (be64_to_cpu(reg_entry->reg_id) != REG_ID("CPUEND")) \ + reg_entry++; \ + reg_entry++; \ }) /* Kernel Dump section info */ struct fadump_section { - u32 request_flag; - u16 source_data_type; - u16 error_flags; - u64 source_address; - u64 source_len; - u64 bytes_dumped; - u64 destination_address; + __be32 request_flag; + __be16 source_data_type; + __be16 error_flags; + __be64 source_address; + __be64 source_len; + __be64 bytes_dumped; + __be64 destination_address; }; /* ibm,configure-kernel-dump header. */ struct fadump_section_header { - u32 dump_format_version; - u16 dump_num_sections; - u16 dump_status_flag; - u32 offset_first_dump_section; + __be32 dump_format_version; + __be16 dump_num_sections; + __be16 dump_status_flag; + __be32 offset_first_dump_section; /* Fields for disk dump option. */ - u32 dd_block_size; - u64 dd_block_offset; - u64 dd_num_blocks; - u32 dd_offset_disk_path; + __be32 dd_block_size; + __be64 dd_block_offset; + __be64 dd_num_blocks; + __be32 dd_offset_disk_path; /* Maximum time allowed to prevent an automatic dump-reboot. */ - u32 max_time_auto; + __be32 max_time_auto; }; /* @@ -174,15 +174,15 @@ static inline u64 str_to_u64(const char *str) /* Register save area header. */ struct fadump_reg_save_area_header { - u64 magic_number; - u32 version; - u32 num_cpu_offset; + __be64 magic_number; + __be32 version; + __be32 num_cpu_offset; }; /* Register entry. */ struct fadump_reg_entry { - u64 reg_id; - u64 reg_value; + __be64 reg_id; + __be64 reg_value; }; /* fadump crash info structure */ diff --git a/arch/powerpc/kernel/fadump.c b/arch/powerpc/kernel/fadump.c index 742694c1d85..26d091a1a54 100644 --- a/arch/powerpc/kernel/fadump.c +++ b/arch/powerpc/kernel/fadump.c @@ -58,7 +58,7 @@ int __init early_init_dt_scan_fw_dump(unsigned long node, const __be32 *sections; int i, num_sections; int size; - const int *token; + const __be32 *token; if (depth != 1 || strcmp(uname, "rtas") != 0) return 0; @@ -72,7 +72,7 @@ int __init early_init_dt_scan_fw_dump(unsigned long node, return 1; fw_dump.fadump_supported = 1; - fw_dump.ibm_configure_kernel_dump = *token; + fw_dump.ibm_configure_kernel_dump = be32_to_cpu(*token); /* * The 'ibm,kernel-dump' rtas node is present only if there is @@ -147,11 +147,11 @@ static unsigned long init_fadump_mem_struct(struct fadump_mem_struct *fdm, memset(fdm, 0, sizeof(struct fadump_mem_struct)); addr = addr & PAGE_MASK; - fdm->header.dump_format_version = 0x00000001; - fdm->header.dump_num_sections = 3; + fdm->header.dump_format_version = cpu_to_be32(0x00000001); + fdm->header.dump_num_sections = cpu_to_be16(3); fdm->header.dump_status_flag = 0; fdm->header.offset_first_dump_section = - (u32)offsetof(struct fadump_mem_struct, cpu_state_data); + cpu_to_be32((u32)offsetof(struct fadump_mem_struct, cpu_state_data)); /* * Fields for disk dump option. @@ -167,27 +167,27 @@ static unsigned long init_fadump_mem_struct(struct fadump_mem_struct *fdm, /* Kernel dump sections */ /* cpu state data section. */ - fdm->cpu_state_data.request_flag = FADUMP_REQUEST_FLAG; - fdm->cpu_state_data.source_data_type = FADUMP_CPU_STATE_DATA; + fdm->cpu_state_data.request_flag = cpu_to_be32(FADUMP_REQUEST_FLAG); + fdm->cpu_state_data.source_data_type = cpu_to_be16(FADUMP_CPU_STATE_DATA); fdm->cpu_state_data.source_address = 0; - fdm->cpu_state_data.source_len = fw_dump.cpu_state_data_size; - fdm->cpu_state_data.destination_address = addr; + fdm->cpu_state_data.source_len = cpu_to_be64(fw_dump.cpu_state_data_size); + fdm->cpu_state_data.destination_address = cpu_to_be64(addr); addr += fw_dump.cpu_state_data_size; /* hpte region section */ - fdm->hpte_region.request_flag = FADUMP_REQUEST_FLAG; - fdm->hpte_region.source_data_type = FADUMP_HPTE_REGION; + fdm->hpte_region.request_flag = cpu_to_be32(FADUMP_REQUEST_FLAG); + fdm->hpte_region.source_data_type = cpu_to_be16(FADUMP_HPTE_REGION); fdm->hpte_region.source_address = 0; - fdm->hpte_region.source_len = fw_dump.hpte_region_size; - fdm->hpte_region.destination_address = addr; + fdm->hpte_region.source_len = cpu_to_be64(fw_dump.hpte_region_size); + fdm->hpte_region.destination_address = cpu_to_be64(addr); addr += fw_dump.hpte_region_size; /* RMA region section */ - fdm->rmr_region.request_flag = FADUMP_REQUEST_FLAG; - fdm->rmr_region.source_data_type = FADUMP_REAL_MODE_REGION; - fdm->rmr_region.source_address = RMA_START; - fdm->rmr_region.source_len = fw_dump.boot_memory_size; - fdm->rmr_region.destination_address = addr; + fdm->rmr_region.request_flag = cpu_to_be32(FADUMP_REQUEST_FLAG); + fdm->rmr_region.source_data_type = cpu_to_be16(FADUMP_REAL_MODE_REGION); + fdm->rmr_region.source_address = cpu_to_be64(RMA_START); + fdm->rmr_region.source_len = cpu_to_be64(fw_dump.boot_memory_size); + fdm->rmr_region.destination_address = cpu_to_be64(addr); addr += fw_dump.boot_memory_size; return addr; @@ -272,7 +272,7 @@ int __init fadump_reserve_mem(void) * first kernel. */ if (fdm_active) - fw_dump.boot_memory_size = fdm_active->rmr_region.source_len; + fw_dump.boot_memory_size = be64_to_cpu(fdm_active->rmr_region.source_len); else fw_dump.boot_memory_size = fadump_calculate_reserve_size(); @@ -314,8 +314,8 @@ int __init fadump_reserve_mem(void) (unsigned long)(base >> 20)); fw_dump.fadumphdr_addr = - fdm_active->rmr_region.destination_address + - fdm_active->rmr_region.source_len; + be64_to_cpu(fdm_active->rmr_region.destination_address) + + be64_to_cpu(fdm_active->rmr_region.source_len); pr_debug("fadumphdr_addr = %p\n", (void *) fw_dump.fadumphdr_addr); } else { @@ -472,9 +472,9 @@ fadump_read_registers(struct fadump_reg_entry *reg_entry, struct pt_regs *regs) { memset(regs, 0, sizeof(struct pt_regs)); - while (reg_entry->reg_id != REG_ID("CPUEND")) { - fadump_set_regval(regs, reg_entry->reg_id, - reg_entry->reg_value); + while (be64_to_cpu(reg_entry->reg_id) != REG_ID("CPUEND")) { + fadump_set_regval(regs, be64_to_cpu(reg_entry->reg_id), + be64_to_cpu(reg_entry->reg_value)); reg_entry++; } reg_entry++; @@ -603,20 +603,20 @@ static int __init fadump_build_cpu_notes(const struct fadump_mem_struct *fdm) if (!fdm->cpu_state_data.bytes_dumped) return -EINVAL; - addr = fdm->cpu_state_data.destination_address; + addr = be64_to_cpu(fdm->cpu_state_data.destination_address); vaddr = __va(addr); reg_header = vaddr; - if (reg_header->magic_number != REGSAVE_AREA_MAGIC) { + if (be64_to_cpu(reg_header->magic_number) != REGSAVE_AREA_MAGIC) { printk(KERN_ERR "Unable to read register save area.\n"); return -ENOENT; } pr_debug("--------CPU State Data------------\n"); - pr_debug("Magic Number: %llx\n", reg_header->magic_number); - pr_debug("NumCpuOffset: %x\n", reg_header->num_cpu_offset); + pr_debug("Magic Number: %llx\n", be64_to_cpu(reg_header->magic_number)); + pr_debug("NumCpuOffset: %x\n", be32_to_cpu(reg_header->num_cpu_offset)); - vaddr += reg_header->num_cpu_offset; - num_cpus = *((u32 *)(vaddr)); + vaddr += be32_to_cpu(reg_header->num_cpu_offset); + num_cpus = be32_to_cpu(*((__be32 *)(vaddr))); pr_debug("NumCpus : %u\n", num_cpus); vaddr += sizeof(u32); reg_entry = (struct fadump_reg_entry *)vaddr; @@ -639,13 +639,13 @@ static int __init fadump_build_cpu_notes(const struct fadump_mem_struct *fdm) fdh = __va(fw_dump.fadumphdr_addr); for (i = 0; i < num_cpus; i++) { - if (reg_entry->reg_id != REG_ID("CPUSTRT")) { + if (be64_to_cpu(reg_entry->reg_id) != REG_ID("CPUSTRT")) { printk(KERN_ERR "Unable to read CPU state data\n"); rc = -ENOENT; goto error_out; } /* Lower 4 bytes of reg_value contains logical cpu id */ - cpu = reg_entry->reg_value & FADUMP_CPU_ID_MASK; + cpu = be64_to_cpu(reg_entry->reg_value) & FADUMP_CPU_ID_MASK; if (fdh && !cpumask_test_cpu(cpu, &fdh->cpu_online_mask)) { SKIP_TO_NEXT_CPU(reg_entry); continue; @@ -692,7 +692,7 @@ static int __init process_fadump(const struct fadump_mem_struct *fdm_active) return -EINVAL; /* Check if the dump data is valid. */ - if ((fdm_active->header.dump_status_flag == FADUMP_ERROR_FLAG) || + if ((be16_to_cpu(fdm_active->header.dump_status_flag) == FADUMP_ERROR_FLAG) || (fdm_active->cpu_state_data.error_flags != 0) || (fdm_active->rmr_region.error_flags != 0)) { printk(KERN_ERR "Dump taken by platform is not valid\n"); @@ -828,7 +828,7 @@ static void fadump_setup_crash_memory_ranges(void) static inline unsigned long fadump_relocate(unsigned long paddr) { if (paddr > RMA_START && paddr < fw_dump.boot_memory_size) - return fdm.rmr_region.destination_address + paddr; + return be64_to_cpu(fdm.rmr_region.destination_address) + paddr; else return paddr; } @@ -902,7 +902,7 @@ static int fadump_create_elfcore_headers(char *bufp) * to the specified destination_address. Hence set * the correct offset. */ - phdr->p_offset = fdm.rmr_region.destination_address; + phdr->p_offset = be64_to_cpu(fdm.rmr_region.destination_address); } phdr->p_paddr = mbase; @@ -951,7 +951,7 @@ static void register_fadump(void) fadump_setup_crash_memory_ranges(); - addr = fdm.rmr_region.destination_address + fdm.rmr_region.source_len; + addr = be64_to_cpu(fdm.rmr_region.destination_address) + be64_to_cpu(fdm.rmr_region.source_len); /* Initialize fadump crash info header. */ addr = init_fadump_header(addr); vaddr = __va(addr); @@ -1023,7 +1023,7 @@ void fadump_cleanup(void) /* Invalidate the registration only if dump is active. */ if (fw_dump.dump_active) { init_fadump_mem_struct(&fdm, - fdm_active->cpu_state_data.destination_address); + be64_to_cpu(fdm_active->cpu_state_data.destination_address)); fadump_invalidate_dump(&fdm); } } @@ -1063,7 +1063,7 @@ static void fadump_invalidate_release_mem(void) return; } - destination_address = fdm_active->cpu_state_data.destination_address; + destination_address = be64_to_cpu(fdm_active->cpu_state_data.destination_address); fadump_cleanup(); mutex_unlock(&fadump_mutex); @@ -1183,31 +1183,31 @@ static int fadump_region_show(struct seq_file *m, void *private) seq_printf(m, "CPU : [%#016llx-%#016llx] %#llx bytes, " "Dumped: %#llx\n", - fdm_ptr->cpu_state_data.destination_address, - fdm_ptr->cpu_state_data.destination_address + - fdm_ptr->cpu_state_data.source_len - 1, - fdm_ptr->cpu_state_data.source_len, - fdm_ptr->cpu_state_data.bytes_dumped); + be64_to_cpu(fdm_ptr->cpu_state_data.destination_address), + be64_to_cpu(fdm_ptr->cpu_state_data.destination_address) + + be64_to_cpu(fdm_ptr->cpu_state_data.source_len) - 1, + be64_to_cpu(fdm_ptr->cpu_state_data.source_len), + be64_to_cpu(fdm_ptr->cpu_state_data.bytes_dumped)); seq_printf(m, "HPTE: [%#016llx-%#016llx] %#llx bytes, " "Dumped: %#llx\n", - fdm_ptr->hpte_region.destination_address, - fdm_ptr->hpte_region.destination_address + - fdm_ptr->hpte_region.source_len - 1, - fdm_ptr->hpte_region.source_len, - fdm_ptr->hpte_region.bytes_dumped); + be64_to_cpu(fdm_ptr->hpte_region.destination_address), + be64_to_cpu(fdm_ptr->hpte_region.destination_address) + + be64_to_cpu(fdm_ptr->hpte_region.source_len) - 1, + be64_to_cpu(fdm_ptr->hpte_region.source_len), + be64_to_cpu(fdm_ptr->hpte_region.bytes_dumped)); seq_printf(m, "DUMP: [%#016llx-%#016llx] %#llx bytes, " "Dumped: %#llx\n", - fdm_ptr->rmr_region.destination_address, - fdm_ptr->rmr_region.destination_address + - fdm_ptr->rmr_region.source_len - 1, - fdm_ptr->rmr_region.source_len, - fdm_ptr->rmr_region.bytes_dumped); + be64_to_cpu(fdm_ptr->rmr_region.destination_address), + be64_to_cpu(fdm_ptr->rmr_region.destination_address) + + be64_to_cpu(fdm_ptr->rmr_region.source_len) - 1, + be64_to_cpu(fdm_ptr->rmr_region.source_len), + be64_to_cpu(fdm_ptr->rmr_region.bytes_dumped)); if (!fdm_active || (fw_dump.reserve_dump_area_start == - fdm_ptr->cpu_state_data.destination_address)) + be64_to_cpu(fdm_ptr->cpu_state_data.destination_address))) goto out; /* Dump is active. Show reserved memory region. */ @@ -1215,10 +1215,10 @@ static int fadump_region_show(struct seq_file *m, void *private) " : [%#016llx-%#016llx] %#llx bytes, " "Dumped: %#llx\n", (unsigned long long)fw_dump.reserve_dump_area_start, - fdm_ptr->cpu_state_data.destination_address - 1, - fdm_ptr->cpu_state_data.destination_address - + be64_to_cpu(fdm_ptr->cpu_state_data.destination_address) - 1, + be64_to_cpu(fdm_ptr->cpu_state_data.destination_address) - fw_dump.reserve_dump_area_start, - fdm_ptr->cpu_state_data.destination_address - + be64_to_cpu(fdm_ptr->cpu_state_data.destination_address) - fw_dump.reserve_dump_area_start); out: if (fdm_active) diff --git a/arch/powerpc/platforms/pseries/lpar.c b/arch/powerpc/platforms/pseries/lpar.c index 8c509d5397c..f6880d2a40f 100644 --- a/arch/powerpc/platforms/pseries/lpar.c +++ b/arch/powerpc/platforms/pseries/lpar.c @@ -43,6 +43,7 @@ #include #include #include +#include #include "pseries.h" @@ -247,8 +248,17 @@ static void pSeries_lpar_hptab_clear(void) } #ifdef __LITTLE_ENDIAN__ - /* Reset exceptions to big endian */ - if (firmware_has_feature(FW_FEATURE_SET_MODE)) { + /* + * Reset exceptions to big endian. + * + * FIXME this is a hack for kexec, we need to reset the exception + * endian before starting the new kernel and this is a convenient place + * to do it. + * + * This is also called on boot when a fadump happens. In that case we + * must not change the exception endian mode. + */ + if (firmware_has_feature(FW_FEATURE_SET_MODE) && !is_fadump_active()) { long rc; rc = pseries_big_endian_exceptions(); -- cgit v1.2.3-70-g09d2 From 7c21539c45eace48e9f6fbdd59347d8416960af5 Mon Sep 17 00:00:00 2001 From: Lukas Bossard Date: Wed, 29 Oct 2014 18:31:07 +0100 Subject: ALSA: hda - Add ultra dock support for Thinkpad X240. Adding ultra doch support for Lenovo Thinkpad X240 (17aa:2214). [Actually replaced the entry with ALC292_FIXUP_TPT440_DOCK -- tiwai] Signed-off-by: Lukas Bossard Cc: Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index c9cf248ce8e..9bc0301ddf4 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -4804,7 +4804,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x17aa, 0x220e, "Thinkpad T440p", ALC292_FIXUP_TPT440_DOCK), SND_PCI_QUIRK(0x17aa, 0x2210, "Thinkpad T540p", ALC292_FIXUP_TPT440_DOCK), SND_PCI_QUIRK(0x17aa, 0x2212, "Thinkpad T440", ALC292_FIXUP_TPT440_DOCK), - SND_PCI_QUIRK(0x17aa, 0x2214, "Thinkpad", ALC269_FIXUP_LIMIT_INT_MIC_BOOST), + SND_PCI_QUIRK(0x17aa, 0x2214, "Thinkpad X240", ALC292_FIXUP_TPT440_DOCK), SND_PCI_QUIRK(0x17aa, 0x2215, "Thinkpad", ALC269_FIXUP_LIMIT_INT_MIC_BOOST), SND_PCI_QUIRK(0x17aa, 0x3978, "IdeaPad Y410P", ALC269_FIXUP_NO_SHUTUP), SND_PCI_QUIRK(0x17aa, 0x5013, "Thinkpad", ALC269_FIXUP_LIMIT_INT_MIC_BOOST), -- cgit v1.2.3-70-g09d2 From 7a5255f17d913581cc8351582676e06d4613c20d Mon Sep 17 00:00:00 2001 From: David Henningsson Date: Thu, 30 Oct 2014 08:26:01 +0100 Subject: ALSA: hda - Set GPIO 4 low for a few HP machines These HP machines needs GPIO 4 low to enable the headphone amplifier. In addition, we still need to control LEDs via vref and GPIO. Cc: stable@vger.kernel.org BugLink: https://bugs.launchpad.net/bugs/1387128 Tested-by: TienFu Chen Signed-off-by: David Henningsson Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 33 +++++++++++++++++++++++++++++---- 1 file changed, 29 insertions(+), 4 deletions(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 9bc0301ddf4..d16d8ec9520 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -3350,6 +3350,27 @@ static void alc269_fixup_hp_gpio_mic1_led(struct hda_codec *codec, } } +static void alc280_fixup_hp_gpio4(struct hda_codec *codec, + const struct hda_fixup *fix, int action) +{ + /* Like hp_gpio_mic1_led, but also needs GPIO4 low to enable headphone amp */ + struct alc_spec *spec = codec->spec; + static const struct hda_verb gpio_init[] = { + { 0x01, AC_VERB_SET_GPIO_MASK, 0x18 }, + { 0x01, AC_VERB_SET_GPIO_DIRECTION, 0x18 }, + {} + }; + + if (action == HDA_FIXUP_ACT_PRE_PROBE) { + spec->gen.vmaster_mute.hook = alc269_fixup_hp_gpio_mute_hook; + spec->gen.cap_sync_hook = alc269_fixup_hp_cap_mic_mute_hook; + spec->gpio_led = 0; + spec->cap_mute_led_nid = 0x18; + snd_hda_add_verbs(codec, gpio_init); + codec->power_filter = led_power_filter; + } +} + static void alc269_fixup_hp_line1_mic1_led(struct hda_codec *codec, const struct hda_fixup *fix, int action) { @@ -4217,6 +4238,7 @@ enum { ALC283_FIXUP_BXBT2807_MIC, ALC255_FIXUP_DELL_WMI_MIC_MUTE_LED, ALC282_FIXUP_ASPIRE_V5_PINS, + ALC280_FIXUP_HP_GPIO4, }; static const struct hda_fixup alc269_fixups[] = { @@ -4680,7 +4702,10 @@ static const struct hda_fixup alc269_fixups[] = { { }, }, }, - + [ALC280_FIXUP_HP_GPIO4] = { + .type = HDA_FIXUP_FUNC, + .v.func = alc280_fixup_hp_gpio4, + }, }; static const struct snd_pci_quirk alc269_fixup_tbl[] = { @@ -4728,7 +4753,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x22cf, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1), SND_PCI_QUIRK(0x103c, 0x22dc, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x22fb, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), - SND_PCI_QUIRK(0x103c, 0x8004, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), + SND_PCI_QUIRK(0x103c, 0x8004, "HP", ALC269_FIXUP_HP_GPIO4), /* ALC290 */ SND_PCI_QUIRK(0x103c, 0x221b, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2221, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), @@ -4742,7 +4767,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x2255, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2256, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2257, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), - SND_PCI_QUIRK(0x103c, 0x2258, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), + SND_PCI_QUIRK(0x103c, 0x2258, "HP", ALC269_FIXUP_HP_GPIO4), SND_PCI_QUIRK(0x103c, 0x2259, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x225a, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2260, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1), @@ -4751,7 +4776,7 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x2265, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1), SND_PCI_QUIRK(0x103c, 0x2272, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2273, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), - SND_PCI_QUIRK(0x103c, 0x2277, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), + SND_PCI_QUIRK(0x103c, 0x2277, "HP", ALC269_FIXUP_HP_GPIO4), SND_PCI_QUIRK(0x103c, 0x2278, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x227f, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1), SND_PCI_QUIRK(0x103c, 0x2282, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1), -- cgit v1.2.3-70-g09d2 From cf51eb9d0c6027d083893f8a72f26d7f007f1ff7 Mon Sep 17 00:00:00 2001 From: David Henningsson Date: Thu, 30 Oct 2014 08:26:02 +0100 Subject: ALSA: hda - change three SSID quirks to one pin quirk These three HP machines all have the same pin config, so we can change it to a pin quirk. Signed-off-by: David Henningsson Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index d16d8ec9520..22d9d2104e9 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -4753,7 +4753,6 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x22cf, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1), SND_PCI_QUIRK(0x103c, 0x22dc, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x22fb, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), - SND_PCI_QUIRK(0x103c, 0x8004, "HP", ALC269_FIXUP_HP_GPIO4), /* ALC290 */ SND_PCI_QUIRK(0x103c, 0x221b, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2221, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), @@ -4767,7 +4766,6 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x2255, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2256, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2257, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), - SND_PCI_QUIRK(0x103c, 0x2258, "HP", ALC269_FIXUP_HP_GPIO4), SND_PCI_QUIRK(0x103c, 0x2259, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x225a, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2260, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1), @@ -4776,7 +4774,6 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x2265, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1), SND_PCI_QUIRK(0x103c, 0x2272, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2273, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), - SND_PCI_QUIRK(0x103c, 0x2277, "HP", ALC269_FIXUP_HP_GPIO4), SND_PCI_QUIRK(0x103c, 0x2278, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x227f, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1), SND_PCI_QUIRK(0x103c, 0x2282, "HP", ALC269_FIXUP_HP_MUTE_LED_MIC1), @@ -5009,6 +5006,19 @@ static const struct snd_hda_pin_quirk alc269_pin_fixup_tbl[] = { {0x17, 0x40000000}, {0x1d, 0x40700001}, {0x21, 0x02211040}), + SND_HDA_PIN_QUIRK(0x10ec0280, 0x103c, "HP", ALC280_FIXUP_HP_GPIO4, + {0x12, 0x90a60130}, + {0x13, 0x40000000}, + {0x14, 0x90170110}, + {0x15, 0x0421101f}, + {0x16, 0x411111f0}, + {0x17, 0x411111f0}, + {0x18, 0x411111f0}, + {0x19, 0x411111f0}, + {0x1a, 0x04a11020}, + {0x1b, 0x411111f0}, + {0x1d, 0x40748605}, + {0x1e, 0x411111f0}), SND_HDA_PIN_QUIRK(0x10ec0280, 0x103c, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED, {0x12, 0x90a60140}, {0x13, 0x40000000}, -- cgit v1.2.3-70-g09d2 From 1df8874bfab15671fe9433ec20807590ba86b334 Mon Sep 17 00:00:00 2001 From: Kailang Yang Date: Wed, 29 Oct 2014 16:10:13 +0800 Subject: ALSA: hda/realtek - Update Initial AMP for EAPD control The default EAPD control uses verb command to control EAPD. Some codec does not have verb command for EAPD. It needs to control by hidden register. This update will avoid wrong behavior for some codec. This patch will fix double setup for EAPD. It just needs to turn on by one site for verb command or hidden register controlled. Detailed changes: - alc889_coef_init() is replaced with alc_update_coef_idx() with a correct COEF value. - for ALC262, ALC887 and ALC900, the EAPD setup via the hidden register is removed because this rather conflicts with the EAPD verb setup. - For ALC888-VC, also the hidden register access is removed in alc888_coef_init(). - Remove the dead #if 0 code for ALC267/ALC268. Signed-off-by: Kailang Yang Cc: Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 34 ++++++++++------------------------ 1 file changed, 10 insertions(+), 24 deletions(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 22d9d2104e9..ba72fffa746 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -291,18 +291,14 @@ static void alc880_unsol_event(struct hda_codec *codec, unsigned int res) /* additional initialization for ALC888 variants */ static void alc888_coef_init(struct hda_codec *codec) { - if (alc_get_coef0(codec) == 0x20) - /* alc888S-VC */ - alc_write_coef_idx(codec, 7, 0x830); - else - /* alc888-VB */ - alc_write_coef_idx(codec, 7, 0x3030); -} - -/* additional initialization for ALC889 variants */ -static void alc889_coef_init(struct hda_codec *codec) -{ - alc_update_coef_idx(codec, 7, 0, 0x2010); + switch (alc_get_coef0(codec) & 0x00f0) { + /* alc888-VA */ + case 0x00: + /* alc888-VB */ + case 0x10: + alc_update_coef_idx(codec, 7, 0, 0x2030); /* Turn EAPD to High */ + break; + } } /* turn on/off EAPD control (only if available) */ @@ -359,25 +355,15 @@ static void alc_auto_init_amp(struct hda_codec *codec, int type) case 0x10ec0260: alc_update_coefex_idx(codec, 0x1a, 7, 0, 0x2010); break; - case 0x10ec0262: case 0x10ec0880: case 0x10ec0882: case 0x10ec0883: case 0x10ec0885: - case 0x10ec0887: - /*case 0x10ec0889:*/ /* this causes an SPDIF problem */ - case 0x10ec0900: - alc889_coef_init(codec); + alc_update_coef_idx(codec, 7, 0, 0x2030); break; case 0x10ec0888: alc888_coef_init(codec); break; -#if 0 /* XXX: This may cause the silent output on speaker on some machines */ - case 0x10ec0267: - case 0x10ec0268: - alc_update_coef_idx(codec, 7, 0, 0x3000); - break; -#endif /* XXX */ } break; } @@ -1710,7 +1696,7 @@ static void alc889_fixup_coef(struct hda_codec *codec, { if (action != HDA_FIXUP_ACT_INIT) return; - alc889_coef_init(codec); + alc_update_coef_idx(codec, 7, 0, 0x2030); } /* toggle speaker-output according to the hp-jack state */ -- cgit v1.2.3-70-g09d2 From f5ee37bd31678d6cb2313631f203794b5c25e862 Mon Sep 17 00:00:00 2001 From: Ilya Dryomov Date: Thu, 9 Oct 2014 17:06:01 +0400 Subject: rbd: use a single workqueue for all devices Using one queue per device doesn't make much sense given that our workfn processes "devices" and not "requests". Switch to a single workqueue for all devices. Signed-off-by: Ilya Dryomov Reviewed-by: Sage Weil --- drivers/block/rbd.c | 33 ++++++++++++++++++--------------- 1 file changed, 18 insertions(+), 15 deletions(-) diff --git a/drivers/block/rbd.c b/drivers/block/rbd.c index 0a54c588e43..be8d44af6ae 100644 --- a/drivers/block/rbd.c +++ b/drivers/block/rbd.c @@ -342,7 +342,6 @@ struct rbd_device { struct list_head rq_queue; /* incoming rq queue */ spinlock_t lock; /* queue, flags, open_count */ - struct workqueue_struct *rq_wq; struct work_struct rq_work; struct rbd_image_header header; @@ -402,6 +401,8 @@ static struct kmem_cache *rbd_segment_name_cache; static int rbd_major; static DEFINE_IDA(rbd_dev_id_ida); +static struct workqueue_struct *rbd_wq; + /* * Default to false for now, as single-major requires >= 0.75 version of * userspace rbd utility. @@ -3452,7 +3453,7 @@ static void rbd_request_fn(struct request_queue *q) } if (queued) - queue_work(rbd_dev->rq_wq, &rbd_dev->rq_work); + queue_work(rbd_wq, &rbd_dev->rq_work); } /* @@ -5242,16 +5243,9 @@ static int rbd_dev_device_setup(struct rbd_device *rbd_dev) set_capacity(rbd_dev->disk, rbd_dev->mapping.size / SECTOR_SIZE); set_disk_ro(rbd_dev->disk, rbd_dev->mapping.read_only); - rbd_dev->rq_wq = alloc_workqueue("%s", WQ_MEM_RECLAIM, 0, - rbd_dev->disk->disk_name); - if (!rbd_dev->rq_wq) { - ret = -ENOMEM; - goto err_out_mapping; - } - ret = rbd_bus_add_dev(rbd_dev); if (ret) - goto err_out_workqueue; + goto err_out_mapping; /* Everything's ready. Announce the disk to the world. */ @@ -5263,9 +5257,6 @@ static int rbd_dev_device_setup(struct rbd_device *rbd_dev) return ret; -err_out_workqueue: - destroy_workqueue(rbd_dev->rq_wq); - rbd_dev->rq_wq = NULL; err_out_mapping: rbd_dev_mapping_clear(rbd_dev); err_out_disk: @@ -5512,7 +5503,6 @@ static void rbd_dev_device_release(struct device *dev) { struct rbd_device *rbd_dev = dev_to_rbd_dev(dev); - destroy_workqueue(rbd_dev->rq_wq); rbd_free_disk(rbd_dev); clear_bit(RBD_DEV_FLAG_EXISTS, &rbd_dev->flags); rbd_dev_mapping_clear(rbd_dev); @@ -5716,11 +5706,21 @@ static int __init rbd_init(void) if (rc) return rc; + /* + * The number of active work items is limited by the number of + * rbd devices, so leave @max_active at default. + */ + rbd_wq = alloc_workqueue(RBD_DRV_NAME, WQ_MEM_RECLAIM, 0); + if (!rbd_wq) { + rc = -ENOMEM; + goto err_out_slab; + } + if (single_major) { rbd_major = register_blkdev(0, RBD_DRV_NAME); if (rbd_major < 0) { rc = rbd_major; - goto err_out_slab; + goto err_out_wq; } } @@ -5738,6 +5738,8 @@ static int __init rbd_init(void) err_out_blkdev: if (single_major) unregister_blkdev(rbd_major, RBD_DRV_NAME); +err_out_wq: + destroy_workqueue(rbd_wq); err_out_slab: rbd_slab_exit(); return rc; @@ -5749,6 +5751,7 @@ static void __exit rbd_exit(void) rbd_sysfs_cleanup(); if (single_major) unregister_blkdev(rbd_major, RBD_DRV_NAME); + destroy_workqueue(rbd_wq); rbd_slab_exit(); } -- cgit v1.2.3-70-g09d2 From 89baaa570ab0b476db09408d209578cfed700e9f Mon Sep 17 00:00:00 2001 From: Mike Christie Date: Thu, 16 Oct 2014 01:50:19 -0500 Subject: libceph: use memalloc flags for net IO This patch has ceph's lib code use the memalloc flags. If the VM layer needs to write data out to free up memory to handle new allocation requests, the block layer must be able to make forward progress. To handle that requirement we use structs like mempools to reserve memory for objects like bios and requests. The problem is when we send/receive block layer requests over the network layer, net skb allocations can fail and the system can lock up. To solve this, the memalloc related flags were added. NBD, iSCSI and NFS uses these flags to tell the network/vm layer that it should use memory reserves to fullfill allcation requests for structs like skbs. I am running ceph in a bunch of VMs in my laptop, so this patch was not tested very harshly. Signed-off-by: Mike Christie Reviewed-by: Ilya Dryomov --- net/ceph/messenger.c | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-) diff --git a/net/ceph/messenger.c b/net/ceph/messenger.c index 559c9f619c2..8d1653caffd 100644 --- a/net/ceph/messenger.c +++ b/net/ceph/messenger.c @@ -484,7 +484,7 @@ static int ceph_tcp_connect(struct ceph_connection *con) IPPROTO_TCP, &sock); if (ret) return ret; - sock->sk->sk_allocation = GFP_NOFS; + sock->sk->sk_allocation = GFP_NOFS | __GFP_MEMALLOC; #ifdef CONFIG_LOCKDEP lockdep_set_class(&sock->sk->sk_lock, &socket_class); @@ -509,6 +509,9 @@ static int ceph_tcp_connect(struct ceph_connection *con) return ret; } + + sk_set_memalloc(sock->sk); + con->sock = sock; return 0; } @@ -2769,8 +2772,11 @@ static void con_work(struct work_struct *work) { struct ceph_connection *con = container_of(work, struct ceph_connection, work.work); + unsigned long pflags = current->flags; bool fault; + current->flags |= PF_MEMALLOC; + mutex_lock(&con->mutex); while (true) { int ret; @@ -2824,6 +2830,8 @@ static void con_work(struct work_struct *work) con_fault_finish(con); con->ops->put(con); + + tsk_restore_flags(current, pflags, PF_MEMALLOC); } /* -- cgit v1.2.3-70-g09d2 From a8d4205623ae965e36c68629db306ca0695a2771 Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Wed, 22 Oct 2014 09:17:24 +0200 Subject: rbd: Fix error recovery in rbd_obj_read_sync() When we fail to allocate page vector in rbd_obj_read_sync() we just basically ignore the problem and continue which will result in an oops later. Fix the problem by returning proper error. CC: Yehuda Sadeh CC: Sage Weil CC: ceph-devel@vger.kernel.org CC: stable@vger.kernel.org Coverity-id: 1226882 Signed-off-by: Jan Kara Signed-off-by: Ilya Dryomov --- drivers/block/rbd.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/block/rbd.c b/drivers/block/rbd.c index be8d44af6ae..27b71a0b72d 100644 --- a/drivers/block/rbd.c +++ b/drivers/block/rbd.c @@ -3533,7 +3533,7 @@ static int rbd_obj_read_sync(struct rbd_device *rbd_dev, page_count = (u32) calc_pages_for(offset, length); pages = ceph_alloc_page_vector(page_count, GFP_KERNEL); if (IS_ERR(pages)) - ret = PTR_ERR(pages); + return PTR_ERR(pages); ret = -ENOMEM; obj_request = rbd_obj_request_create(object_name, offset, length, -- cgit v1.2.3-70-g09d2 From 14edb593338e3811e818aba286237c365f8881a1 Mon Sep 17 00:00:00 2001 From: Tomas Melin Date: Tue, 28 Oct 2014 15:43:14 -0300 Subject: [media] rc-core: fix protocol_change regression in ir_raw_event_register MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit IR receiver using nuvoton-cir and lirc required additional configuration steps after upgrade from kernel 3.16 to 3.17-rcX. Bisected regression to commit da6e162d6a4607362f8478c715c797d84d449f8b ("[media] rc-core: simplify sysfs code"). The regression comes from adding function change_protocol in ir-raw.c. It changes behaviour so that only the protocol enabled by driver's map_name will be active after registration. This breaks user space behaviour, lirc does not get key press signals anymore. Enable lirc protocol by default for ir raw decoders to restore original behaviour. Cc: stable@vger.kernel.org # for v3.17 Signed-off-by: Tomas Melin Acked-by: David Härdeman Signed-off-by: Mauro Carvalho Chehab --- drivers/media/rc/rc-ir-raw.c | 1 - drivers/media/rc/rc-main.c | 2 ++ 2 files changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/media/rc/rc-ir-raw.c b/drivers/media/rc/rc-ir-raw.c index e8fff2add26..b732ac6a26d 100644 --- a/drivers/media/rc/rc-ir-raw.c +++ b/drivers/media/rc/rc-ir-raw.c @@ -262,7 +262,6 @@ int ir_raw_event_register(struct rc_dev *dev) return -ENOMEM; dev->raw->dev = dev; - dev->enabled_protocols = ~0; dev->change_protocol = change_protocol; rc = kfifo_alloc(&dev->raw->kfifo, sizeof(struct ir_raw_event) * MAX_IR_EVENT_SIZE, diff --git a/drivers/media/rc/rc-main.c b/drivers/media/rc/rc-main.c index a7991c7d010..8d3b74c5a71 100644 --- a/drivers/media/rc/rc-main.c +++ b/drivers/media/rc/rc-main.c @@ -1421,6 +1421,8 @@ int rc_register_device(struct rc_dev *dev) if (dev->change_protocol) { u64 rc_type = (1 << rc_map->rc_type); + if (dev->driver_type == RC_DRIVER_IR_RAW) + rc_type |= RC_BIT_LIRC; rc = dev->change_protocol(dev, &rc_type); if (rc < 0) goto out_raw; -- cgit v1.2.3-70-g09d2 From cef83483341e258beed49ce78fb2cc0c46ab1757 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Thu, 30 Oct 2014 06:54:12 -0300 Subject: [media] rc5-decoder: BZ#85721: Fix RC5-SZ decoding MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Changeset e87b540be2dd broke RC5-SZ decoding, as it forgot to add the extra bit check for the enabled protocols at the beginning of the logic. Signed-off-by: Mauro Carvalho Chehab Acked-by: David Härdeman Signed-off-by: Mauro Carvalho Chehab --- drivers/media/rc/ir-rc5-decoder.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/rc/ir-rc5-decoder.c b/drivers/media/rc/ir-rc5-decoder.c index 2ef763928ca..84fa6e9b59a 100644 --- a/drivers/media/rc/ir-rc5-decoder.c +++ b/drivers/media/rc/ir-rc5-decoder.c @@ -53,7 +53,7 @@ static int ir_rc5_decode(struct rc_dev *dev, struct ir_raw_event ev) u32 scancode; enum rc_type protocol; - if (!(dev->enabled_protocols & (RC_BIT_RC5 | RC_BIT_RC5X))) + if (!(dev->enabled_protocols & (RC_BIT_RC5 | RC_BIT_RC5X | RC_BIT_RC5_SZ))) return 0; if (!is_timing_event(ev)) { -- cgit v1.2.3-70-g09d2 From cc040ba269ae6972face1dc7376ab3eaab9f64c8 Mon Sep 17 00:00:00 2001 From: "Lad, Prabhakar" Date: Wed, 29 Oct 2014 09:44:21 +0000 Subject: MAINTAINERS: drop list entry for davinci As davinci-linux-open-source@linux.davincidsp.com is now shut and no more maintained by TI, drop this entry from DAVINCI MACHINE SUPPORT and DAVINCI SERIES MEDIA DRIVER. Signed-off-by: Lad, Prabhakar Cc: Kevin Hilman Cc: arm@kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Acked-by: Sekhar Nori Signed-off-by: Kevin Hilman --- MAINTAINERS | 2 -- 1 file changed, 2 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index 7b765a42e2d..f54ff97d621 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -8465,7 +8465,6 @@ F: arch/arm/mach-s3c24xx/bast-irq.c TI DAVINCI MACHINE SUPPORT M: Sekhar Nori M: Kevin Hilman -L: davinci-linux-open-source@linux.davincidsp.com (moderated for non-subscribers) T: git git://gitorious.org/linux-davinci/linux-davinci.git Q: http://patchwork.kernel.org/project/linux-davinci/list/ S: Supported @@ -8475,7 +8474,6 @@ F: drivers/i2c/busses/i2c-davinci.c TI DAVINCI SERIES MEDIA DRIVER M: Lad, Prabhakar L: linux-media@vger.kernel.org -L: davinci-linux-open-source@linux.davincidsp.com (moderated for non-subscribers) W: http://linuxtv.org/ Q: http://patchwork.linuxtv.org/project/linux-media/list/ T: git git://linuxtv.org/mhadli/v4l-dvb-davinci_devices.git -- cgit v1.2.3-70-g09d2 From f4fd36b8802781238beb99015b40af4425f3dfa9 Mon Sep 17 00:00:00 2001 From: Amit Daniel Kachhap Date: Thu, 30 Oct 2014 12:24:51 +0000 Subject: arm64: psci: fix cpu_suspend to check idle state type for index This fix rectifies the psci cpu_suspend implementation to check the PSCI power state parameter type field associated with the requested idle state index. Acked-by: Lorenzo Pieralisi Signed-off-by: Amit Daniel Kachhap Signed-off-by: Will Deacon --- arch/arm64/kernel/psci.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/kernel/psci.c b/arch/arm64/kernel/psci.c index 866c1c82186..663da771580 100644 --- a/arch/arm64/kernel/psci.c +++ b/arch/arm64/kernel/psci.c @@ -528,7 +528,7 @@ static int __maybe_unused cpu_psci_cpu_suspend(unsigned long index) if (WARN_ON_ONCE(!index)) return -EINVAL; - if (state->type == PSCI_POWER_STATE_TYPE_STANDBY) + if (state[index - 1].type == PSCI_POWER_STATE_TYPE_STANDBY) ret = psci_ops.cpu_suspend(state[index - 1], 0); else ret = __cpu_suspend(index, psci_suspend_finisher); -- cgit v1.2.3-70-g09d2 From 8c5bcded11cb607b1bb5920de3b9c882136d27db Mon Sep 17 00:00:00 2001 From: Ulrich Eckhardt Date: Fri, 10 Oct 2014 14:19:12 -0300 Subject: [media] ds3000: fix LNB supply voltage on Tevii S480 on initialization The Tevii S480 outputs 18V on startup for the LNB supply voltage and does not automatically power down. This blocks other receivers connected to a satellite channel router (EN50494), since the receivers can not send the required DiSEqC sequences when the Tevii card is connected to a the same SCR. This patch switches off the LNB supply voltage on initialization of the frontend. [mchehab@osg.samsung.com: add a comment about why we're explicitly turning off voltage at device init] Cc: stable@vger.kernel.org Signed-off-by: Ulrich Eckhardt Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb-frontends/ds3000.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/media/dvb-frontends/ds3000.c b/drivers/media/dvb-frontends/ds3000.c index 335daeff91b..9d0d0347758 100644 --- a/drivers/media/dvb-frontends/ds3000.c +++ b/drivers/media/dvb-frontends/ds3000.c @@ -864,6 +864,13 @@ struct dvb_frontend *ds3000_attach(const struct ds3000_config *config, memcpy(&state->frontend.ops, &ds3000_ops, sizeof(struct dvb_frontend_ops)); state->frontend.demodulator_priv = state; + + /* + * Some devices like T480 starts with voltage on. Be sure + * to turn voltage off during init, as this can otherwise + * interfere with Unicable SCR systems. + */ + ds3000_set_voltage(&state->frontend, SEC_VOLTAGE_OFF); return &state->frontend; error3: -- cgit v1.2.3-70-g09d2 From 808be31426af57af22268ef0fcb42617beb3d15b Mon Sep 17 00:00:00 2001 From: Anton Blanchard Date: Fri, 31 Oct 2014 16:50:57 +1100 Subject: powerpc: do_notify_resume can be called with bad thread_info flags argument Back in 7230c5644188 ("powerpc: Rework lazy-interrupt handling") we added a call out to restore_interrupts() (written in c) before calling do_notify_resume: bl restore_interrupts addi r3,r1,STACK_FRAME_OVERHEAD bl do_notify_resume Unfortunately do_notify_resume takes two arguments, the second one being the thread_info flags: void do_notify_resume(struct pt_regs *regs, unsigned long thread_info_flags) We do populate r4 (the second argument) earlier, but restore_interrupts() is free to muck it up all it wants. My guess is the gcc compiler gods shone down on us and its register allocator never used r4. Sometimes, rarely, luck is on our side. LLVM on the other hand did trample r4. Signed-off-by: Anton Blanchard Cc: stable@vger.kernel.org Signed-off-by: Michael Ellerman --- arch/powerpc/kernel/entry_64.S | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S index 5bbd1bc8c3b..0905c8da90f 100644 --- a/arch/powerpc/kernel/entry_64.S +++ b/arch/powerpc/kernel/entry_64.S @@ -659,7 +659,13 @@ _GLOBAL(ret_from_except_lite) 3: #endif bl save_nvgprs + /* + * Use a non volatile GPR to save and restore our thread_info flags + * across the call to restore_interrupts. + */ + mr r30,r4 bl restore_interrupts + mr r4,r30 addi r3,r1,STACK_FRAME_OVERHEAD bl do_notify_resume b ret_from_except -- cgit v1.2.3-70-g09d2 From 325e4114043469e5f9923d902b4d30bcc2be8163 Mon Sep 17 00:00:00 2001 From: Benjamin Herrenschmidt Date: Thu, 30 Oct 2014 16:19:13 +1100 Subject: powerpc/powernv: Properly fix LPC debugfs endianness Endian is hard, especially when I designed a stupid FW interface, and I should know better... oh well, this is attempt #2 at fixing this properly. This time it seems to work with all access sizes and I can run my flashing tool (which exercises all sort of access sizes and types to access the SPI controller in the BMC) just fine. Signed-off-by: Benjamin Herrenschmidt CC: stable@vger.kernel.org Signed-off-by: Michael Ellerman --- arch/powerpc/platforms/powernv/opal-lpc.c | 59 +++++++++++++++++++++++++++++++ 1 file changed, 59 insertions(+) diff --git a/arch/powerpc/platforms/powernv/opal-lpc.c b/arch/powerpc/platforms/powernv/opal-lpc.c index ad4b31df779..e4169d68cb3 100644 --- a/arch/powerpc/platforms/powernv/opal-lpc.c +++ b/arch/powerpc/platforms/powernv/opal-lpc.c @@ -216,14 +216,54 @@ static ssize_t lpc_debug_read(struct file *filp, char __user *ubuf, &data, len); if (rc) return -ENXIO; + + /* + * Now there is some trickery with the data returned by OPAL + * as it's the desired data right justified in a 32-bit BE + * word. + * + * This is a very bad interface and I'm to blame for it :-( + * + * So we can't just apply a 32-bit swap to what comes from OPAL, + * because user space expects the *bytes* to be in their proper + * respective positions (ie, LPC position). + * + * So what we really want to do here is to shift data right + * appropriately on a LE kernel. + * + * IE. If the LPC transaction has bytes B0, B1, B2 and B3 in that + * order, we have in memory written to by OPAL at the "data" + * pointer: + * + * Bytes: OPAL "data" LE "data" + * 32-bit: B0 B1 B2 B3 B0B1B2B3 B3B2B1B0 + * 16-bit: B0 B1 0000B0B1 B1B00000 + * 8-bit: B0 000000B0 B0000000 + * + * So a BE kernel will have the leftmost of the above in the MSB + * and rightmost in the LSB and can just then "cast" the u32 "data" + * down to the appropriate quantity and write it. + * + * However, an LE kernel can't. It doesn't need to swap because a + * load from data followed by a store to user are going to preserve + * the byte ordering which is the wire byte order which is what the + * user wants, but in order to "crop" to the right size, we need to + * shift right first. + */ switch(len) { case 4: rc = __put_user((u32)data, (u32 __user *)ubuf); break; case 2: +#ifdef __LITTLE_ENDIAN__ + data >>= 16; +#endif rc = __put_user((u16)data, (u16 __user *)ubuf); break; default: +#ifdef __LITTLE_ENDIAN__ + data >>= 24; +#endif rc = __put_user((u8)data, (u8 __user *)ubuf); break; } @@ -263,12 +303,31 @@ static ssize_t lpc_debug_write(struct file *filp, const char __user *ubuf, else if (todo > 1 && (pos & 1) == 0) len = 2; } + + /* + * Similarly to the read case, we have some trickery here but + * it's different to handle. We need to pass the value to OPAL in + * a register whose layout depends on the access size. We want + * to reproduce the memory layout of the user, however we aren't + * doing a load from user and a store to another memory location + * which would achieve that. Here we pass the value to OPAL via + * a register which is expected to contain the "BE" interpretation + * of the byte sequence. IE: for a 32-bit access, byte 0 should be + * in the MSB. So here we *do* need to byteswap on LE. + * + * User bytes: LE "data" OPAL "data" + * 32-bit: B0 B1 B2 B3 B3B2B1B0 B0B1B2B3 + * 16-bit: B0 B1 0000B1B0 0000B0B1 + * 8-bit: B0 000000B0 000000B0 + */ switch(len) { case 4: rc = __get_user(data, (u32 __user *)ubuf); + data = cpu_to_be32(data); break; case 2: rc = __get_user(data, (u16 __user *)ubuf); + data = cpu_to_be16(data); break; default: rc = __get_user(data, (u8 __user *)ubuf); -- cgit v1.2.3-70-g09d2 From e9226d7c9f1d83278d78675d51acc07e1a78cb27 Mon Sep 17 00:00:00 2001 From: Ilya Dryomov Date: Wed, 22 Oct 2014 18:15:37 +0400 Subject: libceph: eliminate unnecessary allocation in process_one_ticket() Commit c27a3e4d667f ("libceph: do not hard code max auth ticket len") while fixing a buffer overlow tried to keep the same as much of the surrounding code as possible and introduced an unnecessary kmalloc() in the unencrypted ticket path. It is likely to fail on huge tickets, so get rid of it. Signed-off-by: Ilya Dryomov Reviewed-by: Sage Weil --- net/ceph/auth_x.c | 25 ++++++++++--------------- 1 file changed, 10 insertions(+), 15 deletions(-) diff --git a/net/ceph/auth_x.c b/net/ceph/auth_x.c index de6662b14e1..7e38b729696 100644 --- a/net/ceph/auth_x.c +++ b/net/ceph/auth_x.c @@ -149,6 +149,7 @@ static int process_one_ticket(struct ceph_auth_client *ac, struct ceph_crypto_key old_key; void *ticket_buf = NULL; void *tp, *tpend; + void **ptp; struct ceph_timespec new_validity; struct ceph_crypto_key new_session_key; struct ceph_buffer *new_ticket_blob; @@ -208,25 +209,19 @@ static int process_one_ticket(struct ceph_auth_client *ac, goto out; } tp = ticket_buf; - dlen = ceph_decode_32(&tp); + ptp = &tp; + tpend = *ptp + dlen; } else { /* unencrypted */ - ceph_decode_32_safe(p, end, dlen, bad); - ticket_buf = kmalloc(dlen, GFP_NOFS); - if (!ticket_buf) { - ret = -ENOMEM; - goto out; - } - tp = ticket_buf; - ceph_decode_need(p, end, dlen, bad); - ceph_decode_copy(p, ticket_buf, dlen); + ptp = p; + tpend = end; } - tpend = tp + dlen; + ceph_decode_32_safe(ptp, tpend, dlen, bad); dout(" ticket blob is %d bytes\n", dlen); - ceph_decode_need(&tp, tpend, 1 + sizeof(u64), bad); - blob_struct_v = ceph_decode_8(&tp); - new_secret_id = ceph_decode_64(&tp); - ret = ceph_decode_buffer(&new_ticket_blob, &tp, tpend); + ceph_decode_need(ptp, tpend, 1 + sizeof(u64), bad); + blob_struct_v = ceph_decode_8(ptp); + new_secret_id = ceph_decode_64(ptp); + ret = ceph_decode_buffer(&new_ticket_blob, ptp, tpend); if (ret) goto out; -- cgit v1.2.3-70-g09d2 From 10ccaf178b2b961d8bca252d647ed7ed8aae2a20 Mon Sep 17 00:00:00 2001 From: Dan Streetman Date: Fri, 31 Oct 2014 15:41:34 -0400 Subject: powerpc: use device_online/offline() instead of cpu_up/down() In powerpc pseries platform dlpar operations, use device_online() and device_offline() instead of cpu_up() and cpu_down(). Calling cpu_up/down() directly does not update the cpu device offline field, which is used to online/offline a cpu from sysfs. Calling device_online/offline() instead keeps the sysfs cpu online value correct. The hotplug lock, which is required to be held when calling device_online/offline(), is already held when dlpar_online/offline_cpu() are called, since they are called only from cpu_probe|release_store(). This patch fixes errors on phyp (PowerVM) systems that have cpu(s) added/removed using dlpar operations; without this patch, the /sys/devices/system/cpu/cpuN/online nodes do not correctly show the online state of added/removed cpus. Signed-off-by: Dan Streetman Cc: Nathan Fontenot Fixes: 0902a9044fa5 ("Driver core: Use generic offline/online for CPU offline/online") Signed-off-by: Michael Ellerman --- arch/powerpc/platforms/pseries/dlpar.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/powerpc/platforms/pseries/dlpar.c b/arch/powerpc/platforms/pseries/dlpar.c index 6ad83bd11fe..c22bb1b4beb 100644 --- a/arch/powerpc/platforms/pseries/dlpar.c +++ b/arch/powerpc/platforms/pseries/dlpar.c @@ -382,7 +382,7 @@ static int dlpar_online_cpu(struct device_node *dn) BUG_ON(get_cpu_current_state(cpu) != CPU_STATE_OFFLINE); cpu_maps_update_done(); - rc = cpu_up(cpu); + rc = device_online(get_cpu_device(cpu)); if (rc) goto out; cpu_maps_update_begin(); @@ -467,7 +467,7 @@ static int dlpar_offline_cpu(struct device_node *dn) if (get_cpu_current_state(cpu) == CPU_STATE_ONLINE) { set_preferred_offline_state(cpu, CPU_STATE_OFFLINE); cpu_maps_update_done(); - rc = cpu_down(cpu); + rc = device_offline(get_cpu_device(cpu)); if (rc) goto out; cpu_maps_update_begin(); -- cgit v1.2.3-70-g09d2 From 298dcb2dd0267d51e4f7c94a628cd0765a50ad75 Mon Sep 17 00:00:00 2001 From: Grzegorz Jaszczyk Date: Thu, 25 Sep 2014 13:17:18 +0200 Subject: irqchip: armada-370-xp: Fix MSI interrupt handling The MSI interrupts use the 16 high doorbells, which are notified by using IRQ1 of the main interrupt controller. The MSI interrupts were handled correctly for Armada-XP and Armada-370 but not for Armada-375 and Armada-38x, which use chained handler for the MPIC. This commit fixes that by checking proper interrupt number in chained handler for the MPIC. Signed-off-by: Grzegorz Jaszczyk Reviewed-by: Gregory CLEMENT Fixes: bc69b8adfe22 ("irqchip: armada-370-xp: Setup a chained handler for the MPIC") Cc: # v3.15+ Acked-by: Ezequiel Garcia Link: https://lkml.kernel.org/r/1411643839-64925-2-git-send-email-jaz@semihalf.com Signed-off-by: Jason Cooper --- drivers/irqchip/irq-armada-370-xp.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/irqchip/irq-armada-370-xp.c b/drivers/irqchip/irq-armada-370-xp.c index 3e238cd049e..2f01073d620 100644 --- a/drivers/irqchip/irq-armada-370-xp.c +++ b/drivers/irqchip/irq-armada-370-xp.c @@ -413,9 +413,9 @@ static void armada_370_xp_mpic_handle_cascade_irq(unsigned int irq, irqmap = readl_relaxed(per_cpu_int_base + ARMADA_375_PPI_CAUSE); - if (irqmap & BIT(0)) { + if (irqmap & BIT(1)) { armada_370_xp_handle_msi_irq(NULL, true); - irqmap &= ~BIT(0); + irqmap &= ~BIT(1); } for_each_set_bit(irqn, &irqmap, BITS_PER_LONG) { -- cgit v1.2.3-70-g09d2 From 758e8366754d3fa57da978fef9d2c652f7b55c02 Mon Sep 17 00:00:00 2001 From: Grzegorz Jaszczyk Date: Thu, 25 Sep 2014 13:17:19 +0200 Subject: irqchip: armada-370-xp: Fix MPIC interrupt handling In both Armada-375 and Armada-38x MPIC interrupts should be identified by reading cause register multiplied by the interrupt mask. A lack of above mentioned multiplication resulted in a bug, caused by the fact that in Armada-375 and Armada-38x some of the interrupts (e.g. network interrupts) can be handled either as a GIC or MPIC interrupts. Therefore during MPIC interrupts handling, cause register shows hits from interrupts even if they are masked for MPIC but unmasked for a GIC. This resulted in 'bad IRQ' error, because masked MPIC interrupt without registered interrupt handler, was trying to be handled during interrupt handling procedure of some other unmasked MPIC interrupt (e.g. local timer irq). This commit fixes that by ensuring that during MPIC interrupt handling only interrupts that are unmasked for MPIC are processed. Signed-off-by: Grzegorz Jaszczyk Reviewed-by: Gregory CLEMENT Fixes: bc69b8adfe22 ("irqchip: armada-370-xp: Setup a chained handler for the MPIC") Cc: # v3.15+ Acked-by: Ezequiel Garcia Link: https://lkml.kernel.org/r/1411643839-64925-3-git-send-email-jaz@semihalf.com Signed-off-by: Jason Cooper --- drivers/irqchip/irq-armada-370-xp.c | 23 +++++++++++++++++------ 1 file changed, 17 insertions(+), 6 deletions(-) diff --git a/drivers/irqchip/irq-armada-370-xp.c b/drivers/irqchip/irq-armada-370-xp.c index 2f01073d620..6a2e168c3ab 100644 --- a/drivers/irqchip/irq-armada-370-xp.c +++ b/drivers/irqchip/irq-armada-370-xp.c @@ -43,6 +43,7 @@ #define ARMADA_370_XP_INT_CLEAR_ENABLE_OFFS (0x34) #define ARMADA_370_XP_INT_SOURCE_CTL(irq) (0x100 + irq*4) #define ARMADA_370_XP_INT_SOURCE_CPU_MASK 0xF +#define ARMADA_370_XP_INT_IRQ_FIQ_MASK(cpuid) ((BIT(0) | BIT(8)) << cpuid) #define ARMADA_370_XP_CPU_INTACK_OFFS (0x44) #define ARMADA_375_PPI_CAUSE (0x10) @@ -406,19 +407,29 @@ static void armada_370_xp_mpic_handle_cascade_irq(unsigned int irq, struct irq_desc *desc) { struct irq_chip *chip = irq_get_chip(irq); - unsigned long irqmap, irqn; + unsigned long irqmap, irqn, irqsrc, cpuid; unsigned int cascade_irq; chained_irq_enter(chip, desc); irqmap = readl_relaxed(per_cpu_int_base + ARMADA_375_PPI_CAUSE); - - if (irqmap & BIT(1)) { - armada_370_xp_handle_msi_irq(NULL, true); - irqmap &= ~BIT(1); - } + cpuid = cpu_logical_map(smp_processor_id()); for_each_set_bit(irqn, &irqmap, BITS_PER_LONG) { + irqsrc = readl_relaxed(main_int_base + + ARMADA_370_XP_INT_SOURCE_CTL(irqn)); + + /* Check if the interrupt is not masked on current CPU. + * Test IRQ (0-1) and FIQ (8-9) mask bits. + */ + if (!(irqsrc & ARMADA_370_XP_INT_IRQ_FIQ_MASK(cpuid))) + continue; + + if (irqn == 1) { + armada_370_xp_handle_msi_irq(NULL, true); + continue; + } + cascade_irq = irq_find_mapping(armada_370_xp_mpic_domain, irqn); generic_handle_irq(cascade_irq); } -- cgit v1.2.3-70-g09d2 From e841971628fa355358ea6c5b0595eed0a6202595 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Thu, 31 Jul 2014 19:10:59 +0200 Subject: thermal: exynos: remove unused struct exynos_tmu_registers entries Remove unused / write-only entries from struct exynos_tmu_registers. Then remove unused defines while at it. We don't keep the unused/untested features in the kernel just in case that some future hardware might need it. Such code has a real maintainance cost (all other code changes have to take the dead code into account) and usually makes future changes more difficult, not easier (i.e. recent additions of Exynos5420 SoC and Exynos5260 SoC thermal support has not made use of any of the driver's currently unused/untested features, moreover the recently added code is more complex than needed because of the existing dead code). Also all removed dead code is still accessible in the kernel git repository and can be easily brought back if/when needed. There should be no functional changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Kyungmin Park Tested-by: Amit Daniel Kachhap Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_tmu.h | 40 ------------------------------- drivers/thermal/samsung/exynos_tmu_data.c | 5 ---- drivers/thermal/samsung/exynos_tmu_data.h | 29 +--------------------- 3 files changed, 1 insertion(+), 73 deletions(-) diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h index 1b4a6444ea6..44ca6337e94 100644 --- a/drivers/thermal/samsung/exynos_tmu.h +++ b/drivers/thermal/samsung/exynos_tmu.h @@ -85,8 +85,6 @@ enum soc_type { * @triminfo_25_shift: shift bit of the 25 C trim value in triminfo_data reg. * @triminfo_85_shift: shift bit of the 85 C trim value in triminfo_data reg. * @triminfo_ctrl: trim info controller register. - * @triminfo_reload_shift: shift of triminfo reload enable bit in triminfo_ctrl - reg. * @tmu_ctrl: TMU main controller register. * @test_mux_addr_shift: shift bits of test mux address. * @buf_vref_sel_shift: shift bits of reference voltage in tmu_ctrl register. @@ -101,27 +99,13 @@ enum soc_type { register. * @calib_mode_mask: mask bits of calibration mode value in tmu_ctrl register. - * @therm_trip_tq_en_shift: shift bits of thermal trip enable by TQ pin in - tmu_ctrl register. * @core_en_shift: shift bits of TMU core enable bit in tmu_ctrl register. * @tmu_status: register drescribing the TMU status. * @tmu_cur_temp: register containing the current temperature of the TMU. - * @tmu_cur_temp_shift: shift bits of current temp value in tmu_cur_temp - register. * @threshold_temp: register containing the base threshold level. * @threshold_th0: Register containing first set of rising levels. - * @threshold_th0_l0_shift: shift bits of level0 threshold temperature. - * @threshold_th0_l1_shift: shift bits of level1 threshold temperature. - * @threshold_th0_l2_shift: shift bits of level2 threshold temperature. - * @threshold_th0_l3_shift: shift bits of level3 threshold temperature. * @threshold_th1: Register containing second set of rising levels. - * @threshold_th1_l0_shift: shift bits of level0 threshold temperature. - * @threshold_th1_l1_shift: shift bits of level1 threshold temperature. - * @threshold_th1_l2_shift: shift bits of level2 threshold temperature. - * @threshold_th1_l3_shift: shift bits of level3 threshold temperature. * @threshold_th2: Register containing third set of rising levels. - * @threshold_th2_l0_shift: shift bits of level0 threshold temperature. - * @threshold_th3: Register containing fourth set of rising levels. * @threshold_th3_l0_shift: shift bits of level0 threshold temperature. * @tmu_inten: register containing the different threshold interrupt enable bits. @@ -130,9 +114,6 @@ enum soc_type { * @inten_rise2_shift: shift bits of rising 2 interrupt bits. * @inten_rise3_shift: shift bits of rising 3 interrupt bits. * @inten_fall0_shift: shift bits of falling 0 interrupt bits. - * @inten_fall1_shift: shift bits of falling 1 interrupt bits. - * @inten_fall2_shift: shift bits of falling 2 interrupt bits. - * @inten_fall3_shift: shift bits of falling 3 interrupt bits. * @tmu_intstat: Register containing the interrupt status values. * @tmu_intclear: Register for clearing the raised interrupt status. * @intclr_fall_shift: shift bits for interrupt clear fall 0 @@ -142,7 +123,6 @@ enum soc_type { * @emul_con: TMU emulation controller register. * @emul_temp_shift: shift bits of emulation temperature. * @emul_time_shift: shift bits of emulation time. - * @emul_time_mask: mask bits of emulation time. * @tmu_irqstatus: register to find which TMU generated interrupts. * @tmu_pmin: register to get/set the Pmin value. */ @@ -153,7 +133,6 @@ struct exynos_tmu_registers { u32 triminfo_ctrl; u32 triminfo_ctrl1; - u32 triminfo_reload_shift; u32 tmu_ctrl; u32 test_mux_addr_shift; @@ -166,32 +145,17 @@ struct exynos_tmu_registers { u32 buf_slope_sel_mask; u32 calib_mode_shift; u32 calib_mode_mask; - u32 therm_trip_tq_en_shift; u32 core_en_shift; u32 tmu_status; u32 tmu_cur_temp; - u32 tmu_cur_temp_shift; u32 threshold_temp; u32 threshold_th0; - u32 threshold_th0_l0_shift; - u32 threshold_th0_l1_shift; - u32 threshold_th0_l2_shift; - u32 threshold_th0_l3_shift; - u32 threshold_th1; - u32 threshold_th1_l0_shift; - u32 threshold_th1_l1_shift; - u32 threshold_th1_l2_shift; - u32 threshold_th1_l3_shift; - u32 threshold_th2; - u32 threshold_th2_l0_shift; - - u32 threshold_th3; u32 threshold_th3_l0_shift; u32 tmu_inten; @@ -200,9 +164,6 @@ struct exynos_tmu_registers { u32 inten_rise2_shift; u32 inten_rise3_shift; u32 inten_fall0_shift; - u32 inten_fall1_shift; - u32 inten_fall2_shift; - u32 inten_fall3_shift; u32 tmu_intstat; @@ -215,7 +176,6 @@ struct exynos_tmu_registers { u32 emul_con; u32 emul_temp_shift; u32 emul_time_shift; - u32 emul_time_mask; u32 tmu_irqstatus; u32 tmu_pmin; diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c index aa8e0dee205..d5cdfe524a3 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.c +++ b/drivers/thermal/samsung/exynos_tmu_data.c @@ -123,7 +123,6 @@ static const struct exynos_tmu_registers exynos3250_tmu_registers = { .emul_con = EXYNOS_EMUL_CON, .emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT, .emul_time_shift = EXYNOS_EMUL_TIME_SHIFT, - .emul_time_mask = EXYNOS_EMUL_TIME_MASK, }; #define EXYNOS3250_TMU_DATA \ @@ -185,7 +184,6 @@ static const struct exynos_tmu_registers exynos4412_tmu_registers = { .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT, .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT, .triminfo_ctrl = EXYNOS_TMU_TRIMINFO_CON, - .triminfo_reload_shift = EXYNOS_TRIMINFO_RELOAD_SHIFT, .tmu_ctrl = EXYNOS_TMU_REG_CONTROL, .test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT, .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT, @@ -215,7 +213,6 @@ static const struct exynos_tmu_registers exynos4412_tmu_registers = { .emul_con = EXYNOS_EMUL_CON, .emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT, .emul_time_shift = EXYNOS_EMUL_TIME_SHIFT, - .emul_time_mask = EXYNOS_EMUL_TIME_MASK, }; #define EXYNOS4412_TMU_DATA \ @@ -317,7 +314,6 @@ static const struct exynos_tmu_registers exynos5260_tmu_registers = { .emul_con = EXYNOS5260_EMUL_CON, .emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT, .emul_time_shift = EXYNOS_EMUL_TIME_SHIFT, - .emul_time_mask = EXYNOS_EMUL_TIME_MASK, }; #define __EXYNOS5260_TMU_DATA \ @@ -409,7 +405,6 @@ static const struct exynos_tmu_registers exynos5420_tmu_registers = { .emul_con = EXYNOS_EMUL_CON, .emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT, .emul_time_shift = EXYNOS_EMUL_TIME_SHIFT, - .emul_time_mask = EXYNOS_EMUL_TIME_MASK, }; #define __EXYNOS5420_TMU_DATA \ diff --git a/drivers/thermal/samsung/exynos_tmu_data.h b/drivers/thermal/samsung/exynos_tmu_data.h index f0979e59849..9337c5a3616 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.h +++ b/drivers/thermal/samsung/exynos_tmu_data.h @@ -42,20 +42,8 @@ /* Exynos4210 specific registers */ #define EXYNOS4210_TMU_REG_THRESHOLD_TEMP 0x44 #define EXYNOS4210_TMU_REG_TRIG_LEVEL0 0x50 -#define EXYNOS4210_TMU_REG_TRIG_LEVEL1 0x54 -#define EXYNOS4210_TMU_REG_TRIG_LEVEL2 0x58 -#define EXYNOS4210_TMU_REG_TRIG_LEVEL3 0x5C -#define EXYNOS4210_TMU_REG_PAST_TEMP0 0x60 -#define EXYNOS4210_TMU_REG_PAST_TEMP1 0x64 -#define EXYNOS4210_TMU_REG_PAST_TEMP2 0x68 -#define EXYNOS4210_TMU_REG_PAST_TEMP3 0x6C - -#define EXYNOS4210_TMU_TRIG_LEVEL0_MASK 0x1 -#define EXYNOS4210_TMU_TRIG_LEVEL1_MASK 0x10 -#define EXYNOS4210_TMU_TRIG_LEVEL2_MASK 0x100 -#define EXYNOS4210_TMU_TRIG_LEVEL3_MASK 0x1000 + #define EXYNOS4210_TMU_TRIG_LEVEL_MASK 0x1111 -#define EXYNOS4210_TMU_INTCLEAR_VAL 0x1111 /* Exynos5250 and Exynos4412 specific registers */ #define EXYNOS_TMU_TRIMINFO_CON 0x14 @@ -63,14 +51,11 @@ #define EXYNOS_THD_TEMP_FALL 0x54 #define EXYNOS_EMUL_CON 0x80 -#define EXYNOS_TRIMINFO_RELOAD_SHIFT 1 #define EXYNOS_TRIMINFO_25_SHIFT 0 #define EXYNOS_TRIMINFO_85_SHIFT 8 #define EXYNOS_TMU_RISE_INT_MASK 0x111 #define EXYNOS_TMU_RISE_INT_SHIFT 0 #define EXYNOS_TMU_FALL_INT_MASK 0x111 -#define EXYNOS_TMU_CLEAR_RISE_INT 0x111 -#define EXYNOS_TMU_CLEAR_FALL_INT (0x111 << 12) #define EXYNOS_TMU_CLEAR_FALL_INT_SHIFT 12 #define EXYNOS5420_TMU_CLEAR_FALL_INT_SHIFT 16 #define EXYNOS5440_TMU_CLEAR_FALL_INT_SHIFT 4 @@ -85,9 +70,6 @@ #define EXYNOS_TMU_INTEN_RISE2_SHIFT 8 #define EXYNOS_TMU_INTEN_RISE3_SHIFT 12 #define EXYNOS_TMU_INTEN_FALL0_SHIFT 16 -#define EXYNOS_TMU_INTEN_FALL1_SHIFT 20 -#define EXYNOS_TMU_INTEN_FALL2_SHIFT 24 -#define EXYNOS_TMU_INTEN_FALL3_SHIFT 28 #define EXYNOS_EMUL_TIME 0x57F0 #define EXYNOS_EMUL_TIME_MASK 0xffff @@ -122,13 +104,11 @@ #define EXYNOS5440_TMU_S0_7_TH0 0x110 #define EXYNOS5440_TMU_S0_7_TH1 0x130 #define EXYNOS5440_TMU_S0_7_TH2 0x150 -#define EXYNOS5440_TMU_S0_7_EVTEN 0x1F0 #define EXYNOS5440_TMU_S0_7_IRQEN 0x210 #define EXYNOS5440_TMU_S0_7_IRQ 0x230 /* exynos5440 common registers */ #define EXYNOS5440_TMU_IRQ_STATUS 0x000 #define EXYNOS5440_TMU_PMIN 0x004 -#define EXYNOS5440_TMU_TEMP 0x008 #define EXYNOS5440_TMU_RISE_INT_MASK 0xf #define EXYNOS5440_TMU_RISE_INT_SHIFT 0 @@ -138,13 +118,6 @@ #define EXYNOS5440_TMU_INTEN_RISE2_SHIFT 2 #define EXYNOS5440_TMU_INTEN_RISE3_SHIFT 3 #define EXYNOS5440_TMU_INTEN_FALL0_SHIFT 4 -#define EXYNOS5440_TMU_INTEN_FALL1_SHIFT 5 -#define EXYNOS5440_TMU_INTEN_FALL2_SHIFT 6 -#define EXYNOS5440_TMU_INTEN_FALL3_SHIFT 7 -#define EXYNOS5440_TMU_TH_RISE0_SHIFT 0 -#define EXYNOS5440_TMU_TH_RISE1_SHIFT 8 -#define EXYNOS5440_TMU_TH_RISE2_SHIFT 16 -#define EXYNOS5440_TMU_TH_RISE3_SHIFT 24 #define EXYNOS5440_TMU_TH_RISE4_SHIFT 24 #define EXYNOS5440_EFUSE_SWAP_OFFSET 8 -- cgit v1.2.3-70-g09d2 From d37761ecde5f151f4748309fedaa1db53832cc2c Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Thu, 31 Jul 2014 19:11:00 +0200 Subject: thermal: exynos: remove dead code for HW_MODE calibration The commit 1928457 ("thermal: exynos: Add hardware mode thermal calibration support") has added HW_MODE feature but it has never been enabled. As such it has been a dead code for over a year now and should be removed from the kernel. We don't keep the unused/untested features in the kernel just in case that some future hardware might need it. Such code has a real maintainance cost (all other code changes have to take the dead code into account) and usually makes future changes more difficult, not easier (i.e. recent additions of Exynos5420 SoC and Exynos5260 SoC thermal support has not made use of any of the driver's currently unused/untested features, moreover the recently added code is more complex than needed because of the existing dead code). Also all removed dead code is still accessible in the kernel git repository and can be easily brought back if/when needed. There should be no functional changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Kyungmin Park Tested-by: Amit Daniel Kachhap Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_tmu.c | 33 +------------------------------ drivers/thermal/samsung/exynos_tmu.h | 13 ------------ drivers/thermal/samsung/exynos_tmu_data.c | 3 --- drivers/thermal/samsung/exynos_tmu_data.h | 2 -- 4 files changed, 1 insertion(+), 50 deletions(-) diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c index acbff14da3a..4a55f112cc6 100644 --- a/drivers/thermal/samsung/exynos_tmu.c +++ b/drivers/thermal/samsung/exynos_tmu.c @@ -77,9 +77,6 @@ static int temp_to_code(struct exynos_tmu_data *data, u8 temp) struct exynos_tmu_platform_data *pdata = data->pdata; int temp_code; - if (pdata->cal_mode == HW_MODE) - return temp; - if (data->soc == SOC_ARCH_EXYNOS4210) /* temp should range between 25 and 125 */ if (temp < 25 || temp > 125) { @@ -114,9 +111,6 @@ static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code) struct exynos_tmu_platform_data *pdata = data->pdata; int temp; - if (pdata->cal_mode == HW_MODE) - return temp_code; - if (data->soc == SOC_ARCH_EXYNOS4210) /* temp_code should range between 75 and 175 */ if (temp_code < 75 || temp_code > 175) { @@ -167,9 +161,6 @@ static int exynos_tmu_initialize(struct platform_device *pdev) if (TMU_SUPPORTS(pdata, TRIM_RELOAD)) __raw_writel(1, data->base + reg->triminfo_ctrl); - if (pdata->cal_mode == HW_MODE) - goto skip_calib_data; - /* Save trimming info in order to perform calibration */ if (data->soc == SOC_ARCH_EXYNOS5440) { /* @@ -210,7 +201,6 @@ static int exynos_tmu_initialize(struct platform_device *pdev) (pdata->efuse_value >> reg->triminfo_85_shift) & EXYNOS_TMU_TEMP_MASK; -skip_calib_data: if (pdata->max_trigger_level > MAX_THRESHOLD_LEVS) { dev_err(&pdev->dev, "Invalid max trigger level\n"); ret = -EINVAL; @@ -325,7 +315,7 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on) struct exynos_tmu_data *data = platform_get_drvdata(pdev); struct exynos_tmu_platform_data *pdata = data->pdata; const struct exynos_tmu_registers *reg = pdata->registers; - unsigned int con, interrupt_en, cal_val; + unsigned int con, interrupt_en; mutex_lock(&data->lock); clk_enable(data->clk); @@ -351,27 +341,6 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on) con |= (pdata->noise_cancel_mode << reg->therm_trip_mode_shift); } - if (pdata->cal_mode == HW_MODE) { - con &= ~(reg->calib_mode_mask << reg->calib_mode_shift); - cal_val = 0; - switch (pdata->cal_type) { - case TYPE_TWO_POINT_TRIMMING: - cal_val = 3; - break; - case TYPE_ONE_POINT_TRIMMING_85: - cal_val = 2; - break; - case TYPE_ONE_POINT_TRIMMING_25: - cal_val = 1; - break; - case TYPE_NONE: - break; - default: - dev_err(&pdev->dev, "Invalid calibration type, using none\n"); - } - con |= cal_val << reg->calib_mode_shift; - } - if (on) { con |= (1 << reg->core_en_shift); interrupt_en = diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h index 44ca6337e94..789a8f70f45 100644 --- a/drivers/thermal/samsung/exynos_tmu.h +++ b/drivers/thermal/samsung/exynos_tmu.h @@ -34,11 +34,6 @@ enum calibration_type { TYPE_NONE, }; -enum calibration_mode { - SW_MODE, - HW_MODE, -}; - enum soc_type { SOC_ARCH_EXYNOS3250 = 1, SOC_ARCH_EXYNOS4210, @@ -95,10 +90,6 @@ enum soc_type { * @buf_slope_sel_shift: shift bits of amplifier gain value in tmu_ctrl register. * @buf_slope_sel_mask: mask bits of amplifier gain value in tmu_ctrl register. - * @calib_mode_shift: shift bits of calibration mode value in tmu_ctrl - register. - * @calib_mode_mask: mask bits of calibration mode value in tmu_ctrl - register. * @core_en_shift: shift bits of TMU core enable bit in tmu_ctrl register. * @tmu_status: register drescribing the TMU status. * @tmu_cur_temp: register containing the current temperature of the TMU. @@ -143,8 +134,6 @@ struct exynos_tmu_registers { u32 therm_trip_en_shift; u32 buf_slope_sel_shift; u32 buf_slope_sel_mask; - u32 calib_mode_shift; - u32 calib_mode_mask; u32 core_en_shift; u32 tmu_status; @@ -226,7 +215,6 @@ struct exynos_tmu_registers { * @default_temp_offset: default temperature offset in case of no trimming * @test_mux; information if SoC supports test MUX * @cal_type: calibration type for temperature - * @cal_mode: calibration mode for temperature * @freq_clip_table: Table representing frequency reduction percentage. * @freq_tab_count: Count of the above table as frequency reduction may * applicable to only some of the trigger levels. @@ -257,7 +245,6 @@ struct exynos_tmu_platform_data { u8 test_mux; enum calibration_type cal_type; - enum calibration_mode cal_mode; enum soc_type type; struct freq_clip_table freq_tab[4]; unsigned int freq_tab_count; diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c index d5cdfe524a3..1d05bf8235a 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.c +++ b/drivers/thermal/samsung/exynos_tmu_data.c @@ -482,8 +482,6 @@ static const struct exynos_tmu_registers exynos5440_tmu_registers = { .therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT, .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT, .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK, - .calib_mode_shift = EXYNOS_TMU_CALIB_MODE_SHIFT, - .calib_mode_mask = EXYNOS_TMU_CALIB_MODE_MASK, .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT, .tmu_status = EXYNOS5440_TMU_S0_7_STATUS, .tmu_cur_temp = EXYNOS5440_TMU_S0_7_TEMP, @@ -520,7 +518,6 @@ static const struct exynos_tmu_registers exynos5440_tmu_registers = { .reference_voltage = 16, \ .noise_cancel_mode = 4, \ .cal_type = TYPE_ONE_POINT_TRIMMING, \ - .cal_mode = 0, \ .efuse_value = 0x5b2d, \ .min_efuse_value = 16, \ .max_efuse_value = 76, \ diff --git a/drivers/thermal/samsung/exynos_tmu_data.h b/drivers/thermal/samsung/exynos_tmu_data.h index 9337c5a3616..ac03b76c51c 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.h +++ b/drivers/thermal/samsung/exynos_tmu_data.h @@ -62,8 +62,6 @@ #define EXYNOS_TMU_TRIP_MODE_SHIFT 13 #define EXYNOS_TMU_TRIP_MODE_MASK 0x7 #define EXYNOS_TMU_THERM_TRIP_EN_SHIFT 12 -#define EXYNOS_TMU_CALIB_MODE_SHIFT 4 -#define EXYNOS_TMU_CALIB_MODE_MASK 0x3 #define EXYNOS_TMU_INTEN_RISE0_SHIFT 0 #define EXYNOS_TMU_INTEN_RISE1_SHIFT 4 -- cgit v1.2.3-70-g09d2 From 930aa102e2b0ba70ea420999362e2edc4fda15d3 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Thu, 31 Jul 2014 19:11:01 +0200 Subject: thermal: exynos: remove redundant pdata checks from exynos_tmu_initialize() Remove runtime checks for pdata sanity from exynos_tmu_initialize(). The current values hardcoded in pdata will never trigger the checks and checking itself is not proper. The checks in question are done at runtime in a production code for data that is hardcoded inside driver during development time and later it doesn't change. Such data should be verified during development and review time (i.e. by a script parsing relevant data from exynos_tmu_data.c, one can also argue that verification to be done is so simple that the review by a maintainer should be enough). There should be no functional changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Kyungmin Park Tested-by: Amit Daniel Kachhap Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_thermal_common.h | 1 - drivers/thermal/samsung/exynos_tmu.c | 13 ------------- 2 files changed, 14 deletions(-) diff --git a/drivers/thermal/samsung/exynos_thermal_common.h b/drivers/thermal/samsung/exynos_thermal_common.h index 3eb2ed9ea3a..cd4471925cd 100644 --- a/drivers/thermal/samsung/exynos_thermal_common.h +++ b/drivers/thermal/samsung/exynos_thermal_common.h @@ -27,7 +27,6 @@ #define SENSOR_NAME_LEN 16 #define MAX_TRIP_COUNT 8 #define MAX_COOLING_DEVICE 4 -#define MAX_THRESHOLD_LEVS 5 #define ACTIVE_INTERVAL 500 #define IDLE_INTERVAL 10000 diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c index 4a55f112cc6..b9bffad6833 100644 --- a/drivers/thermal/samsung/exynos_tmu.c +++ b/drivers/thermal/samsung/exynos_tmu.c @@ -201,23 +201,10 @@ static int exynos_tmu_initialize(struct platform_device *pdev) (pdata->efuse_value >> reg->triminfo_85_shift) & EXYNOS_TMU_TEMP_MASK; - if (pdata->max_trigger_level > MAX_THRESHOLD_LEVS) { - dev_err(&pdev->dev, "Invalid max trigger level\n"); - ret = -EINVAL; - goto out; - } - for (i = 0; i < pdata->max_trigger_level; i++) { if (!pdata->trigger_levels[i]) continue; - if ((pdata->trigger_type[i] == HW_TRIP) && - (!pdata->trigger_levels[pdata->max_trigger_level - 1])) { - dev_err(&pdev->dev, "Invalid hw trigger level\n"); - ret = -EINVAL; - goto out; - } - /* Count trigger levels except the HW trip*/ if (!(pdata->trigger_type[i] == HW_TRIP)) trigger_levs++; -- cgit v1.2.3-70-g09d2 From 8131a246600f0c34a71cbe1a2e4a19af7e9bc887 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Thu, 31 Jul 2014 19:11:02 +0200 Subject: thermal: exynos: remove redundant threshold_code checks from exynos_tmu_initialize() Remove runtime checks for negative return values of temp_to_code() from exynos_tmu_initialize(). The current level temperature data hardcoded in pdata will never cause a negative temp_to_code() return values and checking itself is not proper. The checks in question are done at runtime in a production code for data that is hardcoded inside driver during development time and later it doesn't change. Such data should be verified during development and review time (i.e. by a script parsing relevant data from exynos_tmu_data.c, one can also argue that verification to be done is so simple that the review by a maintainer should be enough). Theres should be no functional changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Kyungmin Park Tested-by: Amit Daniel Kachhap Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_tmu.c | 16 +--------------- 1 file changed, 1 insertion(+), 15 deletions(-) diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c index b9bffad6833..15574ccede3 100644 --- a/drivers/thermal/samsung/exynos_tmu.c +++ b/drivers/thermal/samsung/exynos_tmu.c @@ -215,10 +215,6 @@ static int exynos_tmu_initialize(struct platform_device *pdev) if (data->soc == SOC_ARCH_EXYNOS4210) { /* Write temperature code for threshold */ threshold_code = temp_to_code(data, pdata->threshold); - if (threshold_code < 0) { - ret = threshold_code; - goto out; - } writeb(threshold_code, data->base + reg->threshold_temp); for (i = 0; i < trigger_levs; i++) @@ -232,19 +228,13 @@ static int exynos_tmu_initialize(struct platform_device *pdev) i < trigger_levs && i < EXYNOS_MAX_TRIGGER_PER_REG; i++) { threshold_code = temp_to_code(data, pdata->trigger_levels[i]); - if (threshold_code < 0) { - ret = threshold_code; - goto out; - } rising_threshold &= ~(0xff << 8 * i); rising_threshold |= threshold_code << 8 * i; if (pdata->threshold_falling) { threshold_code = temp_to_code(data, pdata->trigger_levels[i] - pdata->threshold_falling); - if (threshold_code > 0) - falling_threshold |= - threshold_code << 8 * i; + falling_threshold |= threshold_code << 8 * i; } } @@ -263,10 +253,6 @@ static int exynos_tmu_initialize(struct platform_device *pdev) (pdata->trigger_type[i] == HW_TRIP)) { threshold_code = temp_to_code(data, pdata->trigger_levels[i]); - if (threshold_code < 0) { - ret = threshold_code; - goto out; - } if (i == EXYNOS_MAX_TRIGGER_PER_REG - 1) { /* 1-4 level to be assigned in th0 reg */ rising_threshold &= ~(0xff << 8 * i); -- cgit v1.2.3-70-g09d2 From ddb31d43cb20222f929b0d242bdb516de51b6c23 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Thu, 31 Jul 2014 19:11:03 +0200 Subject: thermal: exynos: simplify temp_to_code() and code_to_temp() * Remove dead temp check from temp_to_code() (this function users in exynos_tmu_initialize() always pass correct temperatures and exynos_tmu_set_emulation() returns early for EXYNOS4210 because TMU_SUPPORT_EMULATION flag is not set on this SoC). * Move temp_code check from code_to_temp() to exynos_tmu_read() (code_to_temp() only user). There should be no functional changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Kyungmin Park Reviewed-by: Amit Daniel Kachhap Tested-by: Amit Daniel Kachhap Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_tmu.c | 28 +++++++++++----------------- 1 file changed, 11 insertions(+), 17 deletions(-) diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c index 15574ccede3..aa4d4fd2b3f 100644 --- a/drivers/thermal/samsung/exynos_tmu.c +++ b/drivers/thermal/samsung/exynos_tmu.c @@ -77,13 +77,6 @@ static int temp_to_code(struct exynos_tmu_data *data, u8 temp) struct exynos_tmu_platform_data *pdata = data->pdata; int temp_code; - if (data->soc == SOC_ARCH_EXYNOS4210) - /* temp should range between 25 and 125 */ - if (temp < 25 || temp > 125) { - temp_code = -EINVAL; - goto out; - } - switch (pdata->cal_type) { case TYPE_TWO_POINT_TRIMMING: temp_code = (temp - pdata->first_point_trim) * @@ -98,7 +91,7 @@ static int temp_to_code(struct exynos_tmu_data *data, u8 temp) temp_code = temp + pdata->default_temp_offset; break; } -out: + return temp_code; } @@ -111,13 +104,6 @@ static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code) struct exynos_tmu_platform_data *pdata = data->pdata; int temp; - if (data->soc == SOC_ARCH_EXYNOS4210) - /* temp_code should range between 75 and 175 */ - if (temp_code < 75 || temp_code > 175) { - temp = -ENODATA; - goto out; - } - switch (pdata->cal_type) { case TYPE_TWO_POINT_TRIMMING: temp = (temp_code - data->temp_error1) * @@ -132,7 +118,7 @@ static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code) temp = temp_code - pdata->default_temp_offset; break; } -out: + return temp; } @@ -346,8 +332,16 @@ static int exynos_tmu_read(struct exynos_tmu_data *data) clk_enable(data->clk); temp_code = readb(data->base + reg->tmu_cur_temp); - temp = code_to_temp(data, temp_code); + if (data->soc == SOC_ARCH_EXYNOS4210) + /* temp_code should range between 75 and 175 */ + if (temp_code < 75 || temp_code > 175) { + temp = -ENODATA; + goto out; + } + + temp = code_to_temp(data, temp_code); +out: clk_disable(data->clk); mutex_unlock(&data->lock); -- cgit v1.2.3-70-g09d2 From ac951af51f417f71bb6830a5d8018755f55715f4 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Thu, 31 Jul 2014 19:11:04 +0200 Subject: thermal: exynos: cache non_hw_trigger_levels in pdata Cache number of non-hardware trigger levels in a new pdata field (non_hw_trigger_levels) and convert code in exynos_tmu_initialize() accordingly. There should be no functional changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Kyungmin Park Reviewed-by: Amit Daniel Kachhap Tested-by: Amit Daniel Kachhap Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_tmu.c | 16 +++------------- drivers/thermal/samsung/exynos_tmu.h | 2 ++ drivers/thermal/samsung/exynos_tmu_data.c | 6 ++++++ 3 files changed, 11 insertions(+), 13 deletions(-) diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c index aa4d4fd2b3f..6bc8a201961 100644 --- a/drivers/thermal/samsung/exynos_tmu.c +++ b/drivers/thermal/samsung/exynos_tmu.c @@ -129,7 +129,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev) const struct exynos_tmu_registers *reg = pdata->registers; unsigned int status, trim_info = 0, con; unsigned int rising_threshold = 0, falling_threshold = 0; - int ret = 0, threshold_code, i, trigger_levs = 0; + int ret = 0, threshold_code, i; mutex_lock(&data->lock); clk_enable(data->clk); @@ -187,15 +187,6 @@ static int exynos_tmu_initialize(struct platform_device *pdev) (pdata->efuse_value >> reg->triminfo_85_shift) & EXYNOS_TMU_TEMP_MASK; - for (i = 0; i < pdata->max_trigger_level; i++) { - if (!pdata->trigger_levels[i]) - continue; - - /* Count trigger levels except the HW trip*/ - if (!(pdata->trigger_type[i] == HW_TRIP)) - trigger_levs++; - } - rising_threshold = readl(data->base + reg->threshold_th0); if (data->soc == SOC_ARCH_EXYNOS4210) { @@ -203,15 +194,14 @@ static int exynos_tmu_initialize(struct platform_device *pdev) threshold_code = temp_to_code(data, pdata->threshold); writeb(threshold_code, data->base + reg->threshold_temp); - for (i = 0; i < trigger_levs; i++) + for (i = 0; i < pdata->non_hw_trigger_levels; i++) writeb(pdata->trigger_levels[i], data->base + reg->threshold_th0 + i * sizeof(reg->threshold_th0)); writel(reg->intclr_rise_mask, data->base + reg->tmu_intclear); } else { /* Write temperature code for rising and falling threshold */ - for (i = 0; - i < trigger_levs && i < EXYNOS_MAX_TRIGGER_PER_REG; i++) { + for (i = 0; i < pdata->non_hw_trigger_levels; i++) { threshold_code = temp_to_code(data, pdata->trigger_levels[i]); rising_threshold &= ~(0xff << 8 * i); diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h index 789a8f70f45..5514d689624 100644 --- a/drivers/thermal/samsung/exynos_tmu.h +++ b/drivers/thermal/samsung/exynos_tmu.h @@ -199,6 +199,7 @@ struct exynos_tmu_registers { * 1 = enable trigger_level[] interrupt, * 0 = disable trigger_level[] interrupt * @max_trigger_level: max trigger level supported by the TMU + * @non_hw_trigger_levels: number of defined non-hardware trigger levels * @gain: gain of amplifier in the positive-TC generator block * 0 <= gain <= 15 * @reference_voltage: reference voltage of amplifier @@ -232,6 +233,7 @@ struct exynos_tmu_platform_data { enum trigger_type trigger_type[MAX_TRIP_COUNT]; bool trigger_enable[MAX_TRIP_COUNT]; u8 max_trigger_level; + u8 non_hw_trigger_levels; u8 gain; u8 reference_voltage; u8 noise_cancel_mode; diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c index 1d05bf8235a..9c81515e74a 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.c +++ b/drivers/thermal/samsung/exynos_tmu_data.c @@ -64,6 +64,7 @@ struct exynos_tmu_init_data const exynos4210_default_tmu_data = { .trigger_type[1] = THROTTLE_ACTIVE, .trigger_type[2] = SW_TRIP, .max_trigger_level = 4, + .non_hw_trigger_levels = 3, .gain = 15, .reference_voltage = 7, .cal_type = TYPE_ONE_POINT_TRIMMING, @@ -140,6 +141,7 @@ static const struct exynos_tmu_registers exynos3250_tmu_registers = { .trigger_type[2] = SW_TRIP, \ .trigger_type[3] = HW_TRIP, \ .max_trigger_level = 4, \ + .non_hw_trigger_levels = 3, \ .gain = 8, \ .reference_voltage = 16, \ .noise_cancel_mode = 4, \ @@ -230,6 +232,7 @@ static const struct exynos_tmu_registers exynos4412_tmu_registers = { .trigger_type[2] = SW_TRIP, \ .trigger_type[3] = HW_TRIP, \ .max_trigger_level = 4, \ + .non_hw_trigger_levels = 3, \ .gain = 8, \ .reference_voltage = 16, \ .noise_cancel_mode = 4, \ @@ -331,6 +334,7 @@ static const struct exynos_tmu_registers exynos5260_tmu_registers = { .trigger_type[2] = SW_TRIP, \ .trigger_type[3] = HW_TRIP, \ .max_trigger_level = 4, \ + .non_hw_trigger_levels = 3, \ .gain = 8, \ .reference_voltage = 16, \ .noise_cancel_mode = 4, \ @@ -422,6 +426,7 @@ static const struct exynos_tmu_registers exynos5420_tmu_registers = { .trigger_type[2] = SW_TRIP, \ .trigger_type[3] = HW_TRIP, \ .max_trigger_level = 4, \ + .non_hw_trigger_levels = 3, \ .gain = 8, \ .reference_voltage = 16, \ .noise_cancel_mode = 4, \ @@ -514,6 +519,7 @@ static const struct exynos_tmu_registers exynos5440_tmu_registers = { .trigger_type[0] = SW_TRIP, \ .trigger_type[4] = HW_TRIP, \ .max_trigger_level = 5, \ + .non_hw_trigger_levels = 1, \ .gain = 5, \ .reference_voltage = 16, \ .noise_cancel_mode = 4, \ -- cgit v1.2.3-70-g09d2 From 9c7a87f146a642447db29327bcedfbe2163da172 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Thu, 31 Jul 2014 19:11:05 +0200 Subject: thermal: exynos: remove redundant pdata checks from exynos_tmu_control() pdata->reference_voltage and pdata->gain are always defined to non-zero values so remove the redundant checks from exynos_tmu_control(). There should be no functional changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Kyungmin Park Tested-by: Amit Daniel Kachhap Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_tmu.c | 12 ++++-------- drivers/thermal/samsung/exynos_tmu.h | 4 ++-- 2 files changed, 6 insertions(+), 10 deletions(-) diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c index 6bc8a201961..122ae663d0a 100644 --- a/drivers/thermal/samsung/exynos_tmu.c +++ b/drivers/thermal/samsung/exynos_tmu.c @@ -274,15 +274,11 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on) if (pdata->test_mux) con |= (pdata->test_mux << reg->test_mux_addr_shift); - if (pdata->reference_voltage) { - con &= ~(reg->buf_vref_sel_mask << reg->buf_vref_sel_shift); - con |= pdata->reference_voltage << reg->buf_vref_sel_shift; - } + con &= ~(reg->buf_vref_sel_mask << reg->buf_vref_sel_shift); + con |= pdata->reference_voltage << reg->buf_vref_sel_shift; - if (pdata->gain) { - con &= ~(reg->buf_slope_sel_mask << reg->buf_slope_sel_shift); - con |= (pdata->gain << reg->buf_slope_sel_shift); - } + con &= ~(reg->buf_slope_sel_mask << reg->buf_slope_sel_shift); + con |= (pdata->gain << reg->buf_slope_sel_shift); if (pdata->noise_cancel_mode) { con &= ~(reg->therm_trip_mode_mask << diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h index 5514d689624..327c64f0721 100644 --- a/drivers/thermal/samsung/exynos_tmu.h +++ b/drivers/thermal/samsung/exynos_tmu.h @@ -201,10 +201,10 @@ struct exynos_tmu_registers { * @max_trigger_level: max trigger level supported by the TMU * @non_hw_trigger_levels: number of defined non-hardware trigger levels * @gain: gain of amplifier in the positive-TC generator block - * 0 <= gain <= 15 + * 0 < gain <= 15 * @reference_voltage: reference voltage of amplifier * in the positive-TC generator block - * 0 <= reference_voltage <= 31 + * 0 < reference_voltage <= 31 * @noise_cancel_mode: noise cancellation mode * 000, 100, 101, 110 and 111 can be different modes * @type: determines the type of SOC -- cgit v1.2.3-70-g09d2 From 99d67fb993bbe2f27b0004332218108d66c78af4 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Thu, 31 Jul 2014 19:11:06 +0200 Subject: thermal: exynos: remove identical values from exynos*_tmu_registers structures There is no need for abstracting configuration for registers that are identical on all SoC types. There should be no functional changes caused by this patch. Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Kyungmin Park Tested-by: Amit Daniel Kachhap Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_tmu.c | 16 ++++++------ drivers/thermal/samsung/exynos_tmu.h | 15 ----------- drivers/thermal/samsung/exynos_tmu_data.c | 42 ------------------------------- 3 files changed, 8 insertions(+), 65 deletions(-) diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c index 122ae663d0a..35437dffaec 100644 --- a/drivers/thermal/samsung/exynos_tmu.c +++ b/drivers/thermal/samsung/exynos_tmu.c @@ -174,7 +174,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev) trim_info = readl(data->base + reg->triminfo_data); } data->temp_error1 = trim_info & EXYNOS_TMU_TEMP_MASK; - data->temp_error2 = ((trim_info >> reg->triminfo_85_shift) & + data->temp_error2 = ((trim_info >> EXYNOS_TRIMINFO_85_SHIFT) & EXYNOS_TMU_TEMP_MASK); if (!data->temp_error1 || @@ -184,7 +184,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev) if (!data->temp_error2) data->temp_error2 = - (pdata->efuse_value >> reg->triminfo_85_shift) & + (pdata->efuse_value >> EXYNOS_TRIMINFO_85_SHIFT) & EXYNOS_TMU_TEMP_MASK; rising_threshold = readl(data->base + reg->threshold_th0); @@ -274,11 +274,11 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on) if (pdata->test_mux) con |= (pdata->test_mux << reg->test_mux_addr_shift); - con &= ~(reg->buf_vref_sel_mask << reg->buf_vref_sel_shift); - con |= pdata->reference_voltage << reg->buf_vref_sel_shift; + con &= ~(EXYNOS_TMU_REF_VOLTAGE_MASK << EXYNOS_TMU_REF_VOLTAGE_SHIFT); + con |= pdata->reference_voltage << EXYNOS_TMU_REF_VOLTAGE_SHIFT; - con &= ~(reg->buf_slope_sel_mask << reg->buf_slope_sel_shift); - con |= (pdata->gain << reg->buf_slope_sel_shift); + con &= ~(EXYNOS_TMU_BUF_SLOPE_SEL_MASK << EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT); + con |= (pdata->gain << EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT); if (pdata->noise_cancel_mode) { con &= ~(reg->therm_trip_mode_mask << @@ -287,7 +287,7 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on) } if (on) { - con |= (1 << reg->core_en_shift); + con |= (1 << EXYNOS_TMU_CORE_EN_SHIFT); interrupt_en = pdata->trigger_enable[3] << reg->inten_rise3_shift | pdata->trigger_enable[2] << reg->inten_rise2_shift | @@ -297,7 +297,7 @@ static void exynos_tmu_control(struct platform_device *pdev, bool on) interrupt_en |= interrupt_en << reg->inten_fall0_shift; } else { - con &= ~(1 << reg->core_en_shift); + con &= ~(1 << EXYNOS_TMU_CORE_EN_SHIFT); interrupt_en = 0; /* Disable all interrupts */ } writel(interrupt_en, data->base + reg->tmu_inten); diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h index 327c64f0721..d503f35e3cd 100644 --- a/drivers/thermal/samsung/exynos_tmu.h +++ b/drivers/thermal/samsung/exynos_tmu.h @@ -77,20 +77,12 @@ enum soc_type { * bitfields. The register validity, offsets and bitfield values may vary * slightly across different exynos SOC's. * @triminfo_data: register containing 2 pont trimming data - * @triminfo_25_shift: shift bit of the 25 C trim value in triminfo_data reg. - * @triminfo_85_shift: shift bit of the 85 C trim value in triminfo_data reg. * @triminfo_ctrl: trim info controller register. * @tmu_ctrl: TMU main controller register. * @test_mux_addr_shift: shift bits of test mux address. - * @buf_vref_sel_shift: shift bits of reference voltage in tmu_ctrl register. - * @buf_vref_sel_mask: mask bits of reference voltage in tmu_ctrl register. * @therm_trip_mode_shift: shift bits of tripping mode in tmu_ctrl register. * @therm_trip_mode_mask: mask bits of tripping mode in tmu_ctrl register. * @therm_trip_en_shift: shift bits of tripping enable in tmu_ctrl register. - * @buf_slope_sel_shift: shift bits of amplifier gain value in tmu_ctrl - register. - * @buf_slope_sel_mask: mask bits of amplifier gain value in tmu_ctrl register. - * @core_en_shift: shift bits of TMU core enable bit in tmu_ctrl register. * @tmu_status: register drescribing the TMU status. * @tmu_cur_temp: register containing the current temperature of the TMU. * @threshold_temp: register containing the base threshold level. @@ -119,22 +111,15 @@ enum soc_type { */ struct exynos_tmu_registers { u32 triminfo_data; - u32 triminfo_25_shift; - u32 triminfo_85_shift; u32 triminfo_ctrl; u32 triminfo_ctrl1; u32 tmu_ctrl; u32 test_mux_addr_shift; - u32 buf_vref_sel_shift; - u32 buf_vref_sel_mask; u32 therm_trip_mode_shift; u32 therm_trip_mode_mask; u32 therm_trip_en_shift; - u32 buf_slope_sel_shift; - u32 buf_slope_sel_mask; - u32 core_en_shift; u32 tmu_status; diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c index 9c81515e74a..82e0732af75 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.c +++ b/drivers/thermal/samsung/exynos_tmu_data.c @@ -27,14 +27,7 @@ #if defined(CONFIG_CPU_EXYNOS4210) static const struct exynos_tmu_registers exynos4210_tmu_registers = { .triminfo_data = EXYNOS_TMU_REG_TRIMINFO, - .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT, - .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT, .tmu_ctrl = EXYNOS_TMU_REG_CONTROL, - .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT, - .buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK, - .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT, - .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK, - .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT, .tmu_status = EXYNOS_TMU_REG_STATUS, .tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP, .threshold_temp = EXYNOS4210_TMU_REG_THRESHOLD_TEMP, @@ -94,18 +87,11 @@ struct exynos_tmu_init_data const exynos4210_default_tmu_data = { #if defined(CONFIG_SOC_EXYNOS3250) static const struct exynos_tmu_registers exynos3250_tmu_registers = { .triminfo_data = EXYNOS_TMU_REG_TRIMINFO, - .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT, - .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT, .tmu_ctrl = EXYNOS_TMU_REG_CONTROL, .test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT, - .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT, - .buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK, .therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT, .therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK, .therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT, - .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT, - .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK, - .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT, .tmu_status = EXYNOS_TMU_REG_STATUS, .tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP, .threshold_th0 = EXYNOS_THD_TEMP_RISE, @@ -183,19 +169,12 @@ struct exynos_tmu_init_data const exynos3250_default_tmu_data = { #if defined(CONFIG_SOC_EXYNOS4412) || defined(CONFIG_SOC_EXYNOS5250) static const struct exynos_tmu_registers exynos4412_tmu_registers = { .triminfo_data = EXYNOS_TMU_REG_TRIMINFO, - .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT, - .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT, .triminfo_ctrl = EXYNOS_TMU_TRIMINFO_CON, .tmu_ctrl = EXYNOS_TMU_REG_CONTROL, .test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT, - .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT, - .buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK, .therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT, .therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK, .therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT, - .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT, - .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK, - .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT, .tmu_status = EXYNOS_TMU_REG_STATUS, .tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP, .threshold_th0 = EXYNOS_THD_TEMP_RISE, @@ -286,18 +265,11 @@ struct exynos_tmu_init_data const exynos5250_default_tmu_data = { #if defined(CONFIG_SOC_EXYNOS5260) static const struct exynos_tmu_registers exynos5260_tmu_registers = { .triminfo_data = EXYNOS_TMU_REG_TRIMINFO, - .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT, - .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT, .tmu_ctrl = EXYNOS_TMU_REG_CONTROL, .tmu_ctrl = EXYNOS_TMU_REG_CONTROL1, - .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT, - .buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK, .therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT, .therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK, .therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT, - .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT, - .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK, - .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT, .tmu_status = EXYNOS_TMU_REG_STATUS, .tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP, .threshold_th0 = EXYNOS_THD_TEMP_RISE, @@ -378,17 +350,10 @@ struct exynos_tmu_init_data const exynos5260_default_tmu_data = { #if defined(CONFIG_SOC_EXYNOS5420) static const struct exynos_tmu_registers exynos5420_tmu_registers = { .triminfo_data = EXYNOS_TMU_REG_TRIMINFO, - .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT, - .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT, .tmu_ctrl = EXYNOS_TMU_REG_CONTROL, - .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT, - .buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK, .therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT, .therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK, .therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT, - .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT, - .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK, - .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT, .tmu_status = EXYNOS_TMU_REG_STATUS, .tmu_cur_temp = EXYNOS_TMU_REG_CURRENT_TEMP, .threshold_th0 = EXYNOS_THD_TEMP_RISE, @@ -477,17 +442,10 @@ struct exynos_tmu_init_data const exynos5420_default_tmu_data = { #if defined(CONFIG_SOC_EXYNOS5440) static const struct exynos_tmu_registers exynos5440_tmu_registers = { .triminfo_data = EXYNOS5440_TMU_S0_7_TRIM, - .triminfo_25_shift = EXYNOS_TRIMINFO_25_SHIFT, - .triminfo_85_shift = EXYNOS_TRIMINFO_85_SHIFT, .tmu_ctrl = EXYNOS5440_TMU_S0_7_CTRL, - .buf_vref_sel_shift = EXYNOS_TMU_REF_VOLTAGE_SHIFT, - .buf_vref_sel_mask = EXYNOS_TMU_REF_VOLTAGE_MASK, .therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT, .therm_trip_mode_mask = EXYNOS_TMU_TRIP_MODE_MASK, .therm_trip_en_shift = EXYNOS_TMU_THERM_TRIP_EN_SHIFT, - .buf_slope_sel_shift = EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT, - .buf_slope_sel_mask = EXYNOS_TMU_BUF_SLOPE_SEL_MASK, - .core_en_shift = EXYNOS_TMU_CORE_EN_SHIFT, .tmu_status = EXYNOS5440_TMU_S0_7_STATUS, .tmu_cur_temp = EXYNOS5440_TMU_S0_7_TEMP, .threshold_th0 = EXYNOS5440_TMU_S0_7_TH0, -- cgit v1.2.3-70-g09d2 From 60e203ecb1faf62efe369ca2bc22630bcda88bdc Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Tue, 26 Aug 2014 10:31:02 +0900 Subject: thermal: samsung: Exynos5260 and Exynos5420 should not use TRIM_RELOAD flag Currently these SoCs claim TRIM_RELOAD support but don't have triminfo_ctrl register address defined in their struct exynos_tmu_registers entries. This causes incorrect write of value "1" to data->base + 0x00 address (which happens to be TRIMINFO register). Additionally according to the documentation that I have neither Exynos5260 nor Exynos5420 support/require TRIM_RELOAD feature. Thus fix the aforementioned issue by removing TMU_SUPPORT_TRIM_RELOAD flag for both Exynos5260 and Exynos5420. Cc: Naveen Krishna Chatradhi Cc: Amit Daniel Kachhap Cc: Eduardo Valentin Cc: Zhang Rui Signed-off-by: Bartlomiej Zolnierkiewicz Signed-off-by: Chanwoo Choi Acked-by: Kyungmin Park Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_tmu_data.c | 16 +++++++--------- 1 file changed, 7 insertions(+), 9 deletions(-) diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c index 82e0732af75..177ada5846c 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.c +++ b/drivers/thermal/samsung/exynos_tmu_data.c @@ -331,9 +331,8 @@ static const struct exynos_tmu_registers exynos5260_tmu_registers = { #define EXYNOS5260_TMU_DATA \ __EXYNOS5260_TMU_DATA \ .type = SOC_ARCH_EXYNOS5260, \ - .features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \ - TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \ - TMU_SUPPORT_EMUL_TIME) + .features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_FALLING_TRIP | \ + TMU_SUPPORT_READY_STATUS | TMU_SUPPORT_EMUL_TIME) struct exynos_tmu_init_data const exynos5260_default_tmu_data = { .tmu_data = { @@ -416,16 +415,15 @@ static const struct exynos_tmu_registers exynos5420_tmu_registers = { #define EXYNOS5420_TMU_DATA \ __EXYNOS5420_TMU_DATA \ .type = SOC_ARCH_EXYNOS5250, \ - .features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \ - TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \ - TMU_SUPPORT_EMUL_TIME) + .features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_FALLING_TRIP | \ + TMU_SUPPORT_READY_STATUS | TMU_SUPPORT_EMUL_TIME) #define EXYNOS5420_TMU_DATA_SHARED \ __EXYNOS5420_TMU_DATA \ .type = SOC_ARCH_EXYNOS5420_TRIMINFO, \ - .features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \ - TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \ - TMU_SUPPORT_EMUL_TIME | TMU_SUPPORT_ADDRESS_MULTIPLE) + .features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_FALLING_TRIP | \ + TMU_SUPPORT_READY_STATUS | TMU_SUPPORT_EMUL_TIME | \ + TMU_SUPPORT_ADDRESS_MULTIPLE) struct exynos_tmu_init_data const exynos5420_default_tmu_data = { .tmu_data = { -- cgit v1.2.3-70-g09d2 From 56c64da7aa31c7e0422ec54e5d0ed60a98f28712 Mon Sep 17 00:00:00 2001 From: Chanwoo Choi Date: Wed, 3 Sep 2014 12:09:02 +0900 Subject: thermal: exynos: Add support for many TRIMINFO_CTRL registers This patch support many TRIMINFO_CTRL registers if specific Exynos SoC has one more TRIMINFO_CTRL registers. Also this patch uses proper 'RELOAD' shift/mask bit operation to set RELOAD feature instead of static value. Signed-off-by: Chanwoo Choi Acked-by: Kyungmin Park Cc: Zhang Rui Cc: Eduardo Valentin Cc: Amit Daniel Kachhap Reviewed-by: Amit Daniel Kachhap Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_thermal_common.h | 1 + drivers/thermal/samsung/exynos_tmu.c | 15 ++++++++++++--- drivers/thermal/samsung/exynos_tmu.h | 7 +++++-- drivers/thermal/samsung/exynos_tmu_data.c | 4 +++- drivers/thermal/samsung/exynos_tmu_data.h | 1 + 5 files changed, 22 insertions(+), 6 deletions(-) diff --git a/drivers/thermal/samsung/exynos_thermal_common.h b/drivers/thermal/samsung/exynos_thermal_common.h index cd4471925cd..158f5aa8dc5 100644 --- a/drivers/thermal/samsung/exynos_thermal_common.h +++ b/drivers/thermal/samsung/exynos_thermal_common.h @@ -27,6 +27,7 @@ #define SENSOR_NAME_LEN 16 #define MAX_TRIP_COUNT 8 #define MAX_COOLING_DEVICE 4 +#define MAX_TRIMINFO_CTRL_REG 2 #define ACTIVE_INTERVAL 500 #define IDLE_INTERVAL 10000 diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c index 35437dffaec..092ab69d628 100644 --- a/drivers/thermal/samsung/exynos_tmu.c +++ b/drivers/thermal/samsung/exynos_tmu.c @@ -127,7 +127,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev) struct exynos_tmu_data *data = platform_get_drvdata(pdev); struct exynos_tmu_platform_data *pdata = data->pdata; const struct exynos_tmu_registers *reg = pdata->registers; - unsigned int status, trim_info = 0, con; + unsigned int status, trim_info = 0, con, ctrl; unsigned int rising_threshold = 0, falling_threshold = 0; int ret = 0, threshold_code, i; @@ -144,8 +144,17 @@ static int exynos_tmu_initialize(struct platform_device *pdev) } } - if (TMU_SUPPORTS(pdata, TRIM_RELOAD)) - __raw_writel(1, data->base + reg->triminfo_ctrl); + if (TMU_SUPPORTS(pdata, TRIM_RELOAD)) { + for (i = 0; i < reg->triminfo_ctrl_count; i++) { + if (pdata->triminfo_reload[i]) { + ctrl = readl(data->base + + reg->triminfo_ctrl[i]); + ctrl |= pdata->triminfo_reload[i]; + writel(ctrl, data->base + + reg->triminfo_ctrl[i]); + } + } + } /* Save trimming info in order to perform calibration */ if (data->soc == SOC_ARCH_EXYNOS5440) { diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h index d503f35e3cd..f67203bfd83 100644 --- a/drivers/thermal/samsung/exynos_tmu.h +++ b/drivers/thermal/samsung/exynos_tmu.h @@ -78,6 +78,7 @@ enum soc_type { * slightly across different exynos SOC's. * @triminfo_data: register containing 2 pont trimming data * @triminfo_ctrl: trim info controller register. + * @triminfo_ctrl_count: the number of trim info controller register. * @tmu_ctrl: TMU main controller register. * @test_mux_addr_shift: shift bits of test mux address. * @therm_trip_mode_shift: shift bits of tripping mode in tmu_ctrl register. @@ -112,8 +113,8 @@ enum soc_type { struct exynos_tmu_registers { u32 triminfo_data; - u32 triminfo_ctrl; - u32 triminfo_ctrl1; + u32 triminfo_ctrl[MAX_TRIMINFO_CTRL_REG]; + u32 triminfo_ctrl_count; u32 tmu_ctrl; u32 test_mux_addr_shift; @@ -200,6 +201,7 @@ struct exynos_tmu_registers { * @second_point_trim: temp value of the second point trimming * @default_temp_offset: default temperature offset in case of no trimming * @test_mux; information if SoC supports test MUX + * @triminfo_reload: reload value to read TRIMINFO register * @cal_type: calibration type for temperature * @freq_clip_table: Table representing frequency reduction percentage. * @freq_tab_count: Count of the above table as frequency reduction may @@ -230,6 +232,7 @@ struct exynos_tmu_platform_data { u8 second_point_trim; u8 default_temp_offset; u8 test_mux; + u8 triminfo_reload[MAX_TRIMINFO_CTRL_REG]; enum calibration_type cal_type; enum soc_type type; diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c index 177ada5846c..362a1e14855 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.c +++ b/drivers/thermal/samsung/exynos_tmu_data.c @@ -169,7 +169,8 @@ struct exynos_tmu_init_data const exynos3250_default_tmu_data = { #if defined(CONFIG_SOC_EXYNOS4412) || defined(CONFIG_SOC_EXYNOS5250) static const struct exynos_tmu_registers exynos4412_tmu_registers = { .triminfo_data = EXYNOS_TMU_REG_TRIMINFO, - .triminfo_ctrl = EXYNOS_TMU_TRIMINFO_CON, + .triminfo_ctrl[0] = EXYNOS_TMU_TRIMINFO_CON, + .triminfo_ctrl_count = 1, .tmu_ctrl = EXYNOS_TMU_REG_CONTROL, .test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT, .therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT, @@ -231,6 +232,7 @@ static const struct exynos_tmu_registers exynos4412_tmu_registers = { .temp_level = 95, \ }, \ .freq_tab_count = 2, \ + .triminfo_reload[0] = EXYNOS_TRIMINFO_RELOAD_ENABLE, \ .registers = &exynos4412_tmu_registers, \ .features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \ TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \ diff --git a/drivers/thermal/samsung/exynos_tmu_data.h b/drivers/thermal/samsung/exynos_tmu_data.h index ac03b76c51c..6b47a174c8f 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.h +++ b/drivers/thermal/samsung/exynos_tmu_data.h @@ -51,6 +51,7 @@ #define EXYNOS_THD_TEMP_FALL 0x54 #define EXYNOS_EMUL_CON 0x80 +#define EXYNOS_TRIMINFO_RELOAD_ENABLE 1 #define EXYNOS_TRIMINFO_25_SHIFT 0 #define EXYNOS_TRIMINFO_85_SHIFT 8 #define EXYNOS_TMU_RISE_INT_MASK 0x111 -- cgit v1.2.3-70-g09d2 From 32a7416423278cf81d89fe9ac990e6e3546fb602 Mon Sep 17 00:00:00 2001 From: Chanwoo Choi Date: Wed, 3 Sep 2014 12:09:03 +0900 Subject: thermal: exynos: Add support for TRIM_RELOAD feature at Exynos3250 This patch add support for TRIM_RELOAD feature at Exynos3250. The TMu of Exynos3250 has two TRIMINFO_CON register and must need to set RELOAD bit before reading TRIMINFO register. Signed-off-by: Chanwoo Choi Acked-by: Kyungmin Park Cc: Zhang Rui Cc: Eduardo Valentin Cc: Amit Daniel Kachhap Reviewed-by: Amit Daniel Kachhap Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_tmu_data.c | 9 +++++++-- drivers/thermal/samsung/exynos_tmu_data.h | 7 +++++-- 2 files changed, 12 insertions(+), 4 deletions(-) diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c index 362a1e14855..8bae1704b9b 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.c +++ b/drivers/thermal/samsung/exynos_tmu_data.c @@ -87,6 +87,9 @@ struct exynos_tmu_init_data const exynos4210_default_tmu_data = { #if defined(CONFIG_SOC_EXYNOS3250) static const struct exynos_tmu_registers exynos3250_tmu_registers = { .triminfo_data = EXYNOS_TMU_REG_TRIMINFO, + .triminfo_ctrl[0] = EXYNOS_TMU_TRIMINFO_CON1, + .triminfo_ctrl[1] = EXYNOS_TMU_TRIMINFO_CON2, + .triminfo_ctrl_count = 2, .tmu_ctrl = EXYNOS_TMU_REG_CONTROL, .test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT, .therm_trip_mode_shift = EXYNOS_TMU_TRIP_MODE_SHIFT, @@ -147,8 +150,10 @@ static const struct exynos_tmu_registers exynos3250_tmu_registers = { .temp_level = 95, \ }, \ .freq_tab_count = 2, \ + .triminfo_reload[0] = EXYNOS_TRIMINFO_RELOAD_ENABLE, \ + .triminfo_reload[1] = EXYNOS_TRIMINFO_RELOAD_ENABLE, \ .registers = &exynos3250_tmu_registers, \ - .features = (TMU_SUPPORT_EMULATION | \ + .features = (TMU_SUPPORT_EMULATION | TMU_SUPPORT_TRIM_RELOAD | \ TMU_SUPPORT_FALLING_TRIP | TMU_SUPPORT_READY_STATUS | \ TMU_SUPPORT_EMUL_TIME) #endif @@ -169,7 +174,7 @@ struct exynos_tmu_init_data const exynos3250_default_tmu_data = { #if defined(CONFIG_SOC_EXYNOS4412) || defined(CONFIG_SOC_EXYNOS5250) static const struct exynos_tmu_registers exynos4412_tmu_registers = { .triminfo_data = EXYNOS_TMU_REG_TRIMINFO, - .triminfo_ctrl[0] = EXYNOS_TMU_TRIMINFO_CON, + .triminfo_ctrl[0] = EXYNOS_TMU_TRIMINFO_CON2, .triminfo_ctrl_count = 1, .tmu_ctrl = EXYNOS_TMU_REG_CONTROL, .test_mux_addr_shift = EXYNOS4412_MUX_ADDR_SHIFT, diff --git a/drivers/thermal/samsung/exynos_tmu_data.h b/drivers/thermal/samsung/exynos_tmu_data.h index 6b47a174c8f..4b8f33c85b3 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.h +++ b/drivers/thermal/samsung/exynos_tmu_data.h @@ -39,14 +39,17 @@ #define EXYNOS_TMU_BUF_SLOPE_SEL_SHIFT 8 #define EXYNOS_TMU_CORE_EN_SHIFT 0 +/* Exynos3250 specific registers */ +#define EXYNOS_TMU_TRIMINFO_CON1 0x10 + /* Exynos4210 specific registers */ #define EXYNOS4210_TMU_REG_THRESHOLD_TEMP 0x44 #define EXYNOS4210_TMU_REG_TRIG_LEVEL0 0x50 #define EXYNOS4210_TMU_TRIG_LEVEL_MASK 0x1111 -/* Exynos5250 and Exynos4412 specific registers */ -#define EXYNOS_TMU_TRIMINFO_CON 0x14 +/* Exynos5250, Exynos4412, Exynos3250 specific registers */ +#define EXYNOS_TMU_TRIMINFO_CON2 0x14 #define EXYNOS_THD_TEMP_RISE 0x50 #define EXYNOS_THD_TEMP_FALL 0x54 #define EXYNOS_EMUL_CON 0x80 -- cgit v1.2.3-70-g09d2 From 689bd24c5e5046b5e5d0aeff9c0b6abf1093fed6 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Thu, 28 Aug 2014 10:12:32 +0200 Subject: thermal: rcar: Add binding docs for new R-Car Gen2 SoCs - r8a7792 (R-Car V2H) - r8a7793 (R-Car M2-N) - r8a7794 (R-Car E2) r8a7791 is now called "R-Car M2-W". Signed-off-by: Geert Uytterhoeven Signed-off-by: Eduardo Valentin --- Documentation/devicetree/bindings/thermal/rcar-thermal.txt | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index 0ef00be44b0..43404b19793 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -7,7 +7,10 @@ Required properties: - "renesas,thermal-r8a73a4" (R-Mobile AP6) - "renesas,thermal-r8a7779" (R-Car H1) - "renesas,thermal-r8a7790" (R-Car H2) - - "renesas,thermal-r8a7791" (R-Car M2) + - "renesas,thermal-r8a7791" (R-Car M2-W) + - "renesas,thermal-r8a7792" (R-Car V2H) + - "renesas,thermal-r8a7793" (R-Car M2-N) + - "renesas,thermal-r8a7794" (R-Car E2) - reg : Address range of the thermal registers. The 1st reg will be recognized as common register if it has "interrupts". -- cgit v1.2.3-70-g09d2 From c2aad93c7edd5e1bc26cc1d80c1c00a954f01946 Mon Sep 17 00:00:00 2001 From: Vladimir Zapolskiy Date: Mon, 29 Sep 2014 02:47:46 +0300 Subject: thermal: fix multiple disbalanced device node counters Here on function return all temporarily used device nodes shall decrement their usage counter. The problems are found with device nodes allocated by for_each_child_of_node(), of_parse_phandle() and of_find_node_by_name(), fix all problems at once. Signed-off-by: Vladimir Zapolskiy Cc: devicetree@vger.kernel.org Cc: Zhang Rui Cc: Eduardo Valentin Signed-off-by: Eduardo Valentin --- drivers/thermal/of-thermal.c | 40 ++++++++++++++++++++++++++++++++-------- 1 file changed, 32 insertions(+), 8 deletions(-) diff --git a/drivers/thermal/of-thermal.c b/drivers/thermal/of-thermal.c index f8eb625b840..62143ba3100 100644 --- a/drivers/thermal/of-thermal.c +++ b/drivers/thermal/of-thermal.c @@ -387,15 +387,18 @@ thermal_zone_of_sensor_register(struct device *dev, int sensor_id, int (*get_trend)(void *, long *)) { struct device_node *np, *child, *sensor_np; + struct thermal_zone_device *tzd = ERR_PTR(-ENODEV); np = of_find_node_by_name(NULL, "thermal-zones"); if (!np) return ERR_PTR(-ENODEV); - if (!dev || !dev->of_node) + if (!dev || !dev->of_node) { + of_node_put(np); return ERR_PTR(-EINVAL); + } - sensor_np = dev->of_node; + sensor_np = of_node_get(dev->of_node); for_each_child_of_node(np, child) { struct of_phandle_args sensor_specs; @@ -422,16 +425,21 @@ thermal_zone_of_sensor_register(struct device *dev, int sensor_id, } if (sensor_specs.np == sensor_np && id == sensor_id) { - of_node_put(np); - return thermal_zone_of_add_sensor(child, sensor_np, - data, - get_temp, - get_trend); + tzd = thermal_zone_of_add_sensor(child, sensor_np, + data, + get_temp, + get_trend); + of_node_put(sensor_specs.np); + of_node_put(child); + goto exit; } + of_node_put(sensor_specs.np); } +exit: + of_node_put(sensor_np); of_node_put(np); - return ERR_PTR(-ENODEV); + return tzd; } EXPORT_SYMBOL_GPL(thermal_zone_of_sensor_register); @@ -623,6 +631,7 @@ static int thermal_of_populate_trip(struct device_node *np, /* Required for cooling map matching */ trip->np = np; + of_node_get(np); return 0; } @@ -730,9 +739,14 @@ finish: return tz; free_tbps: + for (i = 0; i < tz->num_tbps; i++) + of_node_put(tz->tbps[i].cooling_device); kfree(tz->tbps); free_trips: + for (i = 0; i < tz->ntrips; i++) + of_node_put(tz->trips[i].np); kfree(tz->trips); + of_node_put(gchild); free_tz: kfree(tz); of_node_put(child); @@ -742,7 +756,13 @@ free_tz: static inline void of_thermal_free_zone(struct __thermal_zone *tz) { + int i; + + for (i = 0; i < tz->num_tbps; i++) + of_node_put(tz->tbps[i].cooling_device); kfree(tz->tbps); + for (i = 0; i < tz->ntrips; i++) + of_node_put(tz->trips[i].np); kfree(tz->trips); kfree(tz); } @@ -814,10 +834,13 @@ int __init of_parse_thermal_zones(void) /* attempting to build remaining zones still */ } } + of_node_put(np); return 0; exit_free: + of_node_put(child); + of_node_put(np); of_thermal_free_zone(tz); /* no memory available, so free what we have built */ @@ -859,4 +882,5 @@ void of_thermal_destroy_zones(void) kfree(zone->ops); of_thermal_free_zone(zone->devdata); } + of_node_put(np); } -- cgit v1.2.3-70-g09d2 From b835ced1fd05c43bd4a706050963678bc6e95bc7 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Fri, 3 Oct 2014 18:17:17 +0200 Subject: thermal: exynos: fix IRQ clearing on TMU initialization * Factor out code for clearing raised IRQs from exynos_tmu_work() to exynos_tmu_clear_irqs(). * Add a comment about documentation bugs to exynos_tmu_clear_irqs(). [ The documentation for Exynos3250, Exynos4412, Exynos5250 and Exynos5260 incorrectly states that INTCLEAR register has a different placing of bits responsible for FALL IRQs than INTSTAT register. Exynos5420 and Exynos5440 documentation is correct (Exynos4210 doesn't support FALL IRQs at all). ] * Use exynos_tmu_clear_irqs() in exynos_tmu_initialize() instead of open-coded code trying to clear IRQs according to predefined masks. After this change exynos_tmu_initialize() just clears IRQs that are raised like it is already done in exynos_tmu_work(). As a nice side-effect the code now uses the correct offset (16 instead of 12) for bits responsible for clearing FALL IRQs in INTCLEAR register on Exynos3250, Exynos4412 and Exynos5250. * Remove no longer needed intclr_rise_[mask,shift] and intclr_fall_[mask,shift] fields from struct exynos_tmu_registers. * Remove no longer needed defines. This patch has been tested on Exynos4412 and Exynos5420 SoCs. Cc: Amit Daniel Kachhap Cc: Lukasz Majewski Cc: Eduardo Valentin Cc: Zhang Rui Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Kyungmin Park Signed-off-by: Eduardo Valentin --- drivers/thermal/samsung/exynos_tmu.c | 29 +++++++++++++++++++++-------- drivers/thermal/samsung/exynos_tmu.h | 8 -------- drivers/thermal/samsung/exynos_tmu_data.c | 21 --------------------- drivers/thermal/samsung/exynos_tmu_data.h | 15 --------------- 4 files changed, 21 insertions(+), 52 deletions(-) diff --git a/drivers/thermal/samsung/exynos_tmu.c b/drivers/thermal/samsung/exynos_tmu.c index 092ab69d628..49c09243fd3 100644 --- a/drivers/thermal/samsung/exynos_tmu.c +++ b/drivers/thermal/samsung/exynos_tmu.c @@ -122,6 +122,23 @@ static int code_to_temp(struct exynos_tmu_data *data, u8 temp_code) return temp; } +static void exynos_tmu_clear_irqs(struct exynos_tmu_data *data) +{ + const struct exynos_tmu_registers *reg = data->pdata->registers; + unsigned int val_irq; + + val_irq = readl(data->base + reg->tmu_intstat); + /* + * Clear the interrupts. Please note that the documentation for + * Exynos3250, Exynos4412, Exynos5250 and Exynos5260 incorrectly + * states that INTCLEAR register has a different placing of bits + * responsible for FALL IRQs than INTSTAT register. Exynos5420 + * and Exynos5440 documentation is correct (Exynos4210 doesn't + * support FALL IRQs at all). + */ + writel(val_irq, data->base + reg->tmu_intclear); +} + static int exynos_tmu_initialize(struct platform_device *pdev) { struct exynos_tmu_data *data = platform_get_drvdata(pdev); @@ -207,7 +224,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev) writeb(pdata->trigger_levels[i], data->base + reg->threshold_th0 + i * sizeof(reg->threshold_th0)); - writel(reg->intclr_rise_mask, data->base + reg->tmu_intclear); + exynos_tmu_clear_irqs(data); } else { /* Write temperature code for rising and falling threshold */ for (i = 0; i < pdata->non_hw_trigger_levels; i++) { @@ -228,9 +245,7 @@ static int exynos_tmu_initialize(struct platform_device *pdev) writel(falling_threshold, data->base + reg->threshold_th1); - writel((reg->intclr_rise_mask << reg->intclr_rise_shift) | - (reg->intclr_fall_mask << reg->intclr_fall_shift), - data->base + reg->tmu_intclear); + exynos_tmu_clear_irqs(data); /* if last threshold limit is also present */ i = pdata->max_trigger_level - 1; @@ -396,7 +411,7 @@ static void exynos_tmu_work(struct work_struct *work) struct exynos_tmu_data, irq_work); struct exynos_tmu_platform_data *pdata = data->pdata; const struct exynos_tmu_registers *reg = pdata->registers; - unsigned int val_irq, val_type; + unsigned int val_type; if (!IS_ERR(data->clk_sec)) clk_enable(data->clk_sec); @@ -414,9 +429,7 @@ static void exynos_tmu_work(struct work_struct *work) clk_enable(data->clk); /* TODO: take action based on particular interrupt */ - val_irq = readl(data->base + reg->tmu_intstat); - /* clear the interrupts */ - writel(val_irq, data->base + reg->tmu_intclear); + exynos_tmu_clear_irqs(data); clk_disable(data->clk); mutex_unlock(&data->lock); diff --git a/drivers/thermal/samsung/exynos_tmu.h b/drivers/thermal/samsung/exynos_tmu.h index f67203bfd83..c58c7663a3f 100644 --- a/drivers/thermal/samsung/exynos_tmu.h +++ b/drivers/thermal/samsung/exynos_tmu.h @@ -100,10 +100,6 @@ enum soc_type { * @inten_fall0_shift: shift bits of falling 0 interrupt bits. * @tmu_intstat: Register containing the interrupt status values. * @tmu_intclear: Register for clearing the raised interrupt status. - * @intclr_fall_shift: shift bits for interrupt clear fall 0 - * @intclr_rise_shift: shift bits of all rising interrupt bits. - * @intclr_rise_mask: mask bits of all rising interrupt bits. - * @intclr_fall_mask: mask bits of all rising interrupt bits. * @emul_con: TMU emulation controller register. * @emul_temp_shift: shift bits of emulation temperature. * @emul_time_shift: shift bits of emulation time. @@ -143,10 +139,6 @@ struct exynos_tmu_registers { u32 tmu_intstat; u32 tmu_intclear; - u32 intclr_fall_shift; - u32 intclr_rise_shift; - u32 intclr_fall_mask; - u32 intclr_rise_mask; u32 emul_con; u32 emul_temp_shift; diff --git a/drivers/thermal/samsung/exynos_tmu_data.c b/drivers/thermal/samsung/exynos_tmu_data.c index 8bae1704b9b..2683d2897e9 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.c +++ b/drivers/thermal/samsung/exynos_tmu_data.c @@ -39,7 +39,6 @@ static const struct exynos_tmu_registers exynos4210_tmu_registers = { .inten_rise3_shift = EXYNOS_TMU_INTEN_RISE3_SHIFT, .tmu_intstat = EXYNOS_TMU_REG_INTSTAT, .tmu_intclear = EXYNOS_TMU_REG_INTCLEAR, - .intclr_rise_mask = EXYNOS4210_TMU_TRIG_LEVEL_MASK, }; struct exynos_tmu_init_data const exynos4210_default_tmu_data = { @@ -106,10 +105,6 @@ static const struct exynos_tmu_registers exynos3250_tmu_registers = { .inten_fall0_shift = EXYNOS_TMU_INTEN_FALL0_SHIFT, .tmu_intstat = EXYNOS_TMU_REG_INTSTAT, .tmu_intclear = EXYNOS_TMU_REG_INTCLEAR, - .intclr_fall_shift = EXYNOS_TMU_CLEAR_FALL_INT_SHIFT, - .intclr_rise_shift = EXYNOS_TMU_RISE_INT_SHIFT, - .intclr_rise_mask = EXYNOS_TMU_RISE_INT_MASK, - .intclr_fall_mask = EXYNOS_TMU_FALL_INT_MASK, .emul_con = EXYNOS_EMUL_CON, .emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT, .emul_time_shift = EXYNOS_EMUL_TIME_SHIFT, @@ -193,10 +188,6 @@ static const struct exynos_tmu_registers exynos4412_tmu_registers = { .inten_fall0_shift = EXYNOS_TMU_INTEN_FALL0_SHIFT, .tmu_intstat = EXYNOS_TMU_REG_INTSTAT, .tmu_intclear = EXYNOS_TMU_REG_INTCLEAR, - .intclr_fall_shift = EXYNOS_TMU_CLEAR_FALL_INT_SHIFT, - .intclr_rise_shift = EXYNOS_TMU_RISE_INT_SHIFT, - .intclr_rise_mask = EXYNOS_TMU_RISE_INT_MASK, - .intclr_fall_mask = EXYNOS_TMU_FALL_INT_MASK, .emul_con = EXYNOS_EMUL_CON, .emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT, .emul_time_shift = EXYNOS_EMUL_TIME_SHIFT, @@ -289,10 +280,6 @@ static const struct exynos_tmu_registers exynos5260_tmu_registers = { .inten_fall0_shift = EXYNOS_TMU_INTEN_FALL0_SHIFT, .tmu_intstat = EXYNOS5260_TMU_REG_INTSTAT, .tmu_intclear = EXYNOS5260_TMU_REG_INTCLEAR, - .intclr_fall_shift = EXYNOS5420_TMU_CLEAR_FALL_INT_SHIFT, - .intclr_rise_shift = EXYNOS_TMU_RISE_INT_SHIFT, - .intclr_rise_mask = EXYNOS5260_TMU_RISE_INT_MASK, - .intclr_fall_mask = EXYNOS5260_TMU_FALL_INT_MASK, .emul_con = EXYNOS5260_EMUL_CON, .emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT, .emul_time_shift = EXYNOS_EMUL_TIME_SHIFT, @@ -373,10 +360,6 @@ static const struct exynos_tmu_registers exynos5420_tmu_registers = { .inten_fall0_shift = EXYNOS_TMU_INTEN_FALL0_SHIFT, .tmu_intstat = EXYNOS_TMU_REG_INTSTAT, .tmu_intclear = EXYNOS_TMU_REG_INTCLEAR, - .intclr_fall_shift = EXYNOS5420_TMU_CLEAR_FALL_INT_SHIFT, - .intclr_rise_shift = EXYNOS_TMU_RISE_INT_SHIFT, - .intclr_rise_mask = EXYNOS_TMU_RISE_INT_MASK, - .intclr_fall_mask = EXYNOS_TMU_FALL_INT_MASK, .emul_con = EXYNOS_EMUL_CON, .emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT, .emul_time_shift = EXYNOS_EMUL_TIME_SHIFT, @@ -465,10 +448,6 @@ static const struct exynos_tmu_registers exynos5440_tmu_registers = { .inten_fall0_shift = EXYNOS5440_TMU_INTEN_FALL0_SHIFT, .tmu_intstat = EXYNOS5440_TMU_S0_7_IRQ, .tmu_intclear = EXYNOS5440_TMU_S0_7_IRQ, - .intclr_fall_shift = EXYNOS5440_TMU_CLEAR_FALL_INT_SHIFT, - .intclr_rise_shift = EXYNOS5440_TMU_RISE_INT_SHIFT, - .intclr_rise_mask = EXYNOS5440_TMU_RISE_INT_MASK, - .intclr_fall_mask = EXYNOS5440_TMU_FALL_INT_MASK, .tmu_irqstatus = EXYNOS5440_TMU_IRQ_STATUS, .emul_con = EXYNOS5440_TMU_S0_7_DEBUG, .emul_temp_shift = EXYNOS_EMUL_DATA_SHIFT, diff --git a/drivers/thermal/samsung/exynos_tmu_data.h b/drivers/thermal/samsung/exynos_tmu_data.h index 4b8f33c85b3..65e2ea6a957 100644 --- a/drivers/thermal/samsung/exynos_tmu_data.h +++ b/drivers/thermal/samsung/exynos_tmu_data.h @@ -46,8 +46,6 @@ #define EXYNOS4210_TMU_REG_THRESHOLD_TEMP 0x44 #define EXYNOS4210_TMU_REG_TRIG_LEVEL0 0x50 -#define EXYNOS4210_TMU_TRIG_LEVEL_MASK 0x1111 - /* Exynos5250, Exynos4412, Exynos3250 specific registers */ #define EXYNOS_TMU_TRIMINFO_CON2 0x14 #define EXYNOS_THD_TEMP_RISE 0x50 @@ -57,12 +55,6 @@ #define EXYNOS_TRIMINFO_RELOAD_ENABLE 1 #define EXYNOS_TRIMINFO_25_SHIFT 0 #define EXYNOS_TRIMINFO_85_SHIFT 8 -#define EXYNOS_TMU_RISE_INT_MASK 0x111 -#define EXYNOS_TMU_RISE_INT_SHIFT 0 -#define EXYNOS_TMU_FALL_INT_MASK 0x111 -#define EXYNOS_TMU_CLEAR_FALL_INT_SHIFT 12 -#define EXYNOS5420_TMU_CLEAR_FALL_INT_SHIFT 16 -#define EXYNOS5440_TMU_CLEAR_FALL_INT_SHIFT 4 #define EXYNOS_TMU_TRIP_MODE_SHIFT 13 #define EXYNOS_TMU_TRIP_MODE_MASK 0x7 #define EXYNOS_TMU_THERM_TRIP_EN_SHIFT 12 @@ -87,10 +79,6 @@ #define EXYNOS5260_TMU_REG_INTEN 0xC0 #define EXYNOS5260_TMU_REG_INTSTAT 0xC4 #define EXYNOS5260_TMU_REG_INTCLEAR 0xC8 -#define EXYNOS5260_TMU_CLEAR_RISE_INT 0x1111 -#define EXYNOS5260_TMU_CLEAR_FALL_INT (0x1111 << 16) -#define EXYNOS5260_TMU_RISE_INT_MASK 0x1111 -#define EXYNOS5260_TMU_FALL_INT_MASK 0x1111 #define EXYNOS5260_EMUL_CON 0x100 /* Exynos4412 specific */ @@ -112,9 +100,6 @@ #define EXYNOS5440_TMU_IRQ_STATUS 0x000 #define EXYNOS5440_TMU_PMIN 0x004 -#define EXYNOS5440_TMU_RISE_INT_MASK 0xf -#define EXYNOS5440_TMU_RISE_INT_SHIFT 0 -#define EXYNOS5440_TMU_FALL_INT_MASK 0xf #define EXYNOS5440_TMU_INTEN_RISE0_SHIFT 0 #define EXYNOS5440_TMU_INTEN_RISE1_SHIFT 1 #define EXYNOS5440_TMU_INTEN_RISE2_SHIFT 2 -- cgit v1.2.3-70-g09d2 From 191252837626fca0de694c18bb2aa64c118eda89 Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 29 Oct 2014 09:07:30 +0100 Subject: USB: kobil_sct: fix non-atomic allocation in write path Write may be called from interrupt context so make sure to use GFP_ATOMIC for all allocations in write. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable Signed-off-by: Johan Hovold --- drivers/usb/serial/kobil_sct.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/usb/serial/kobil_sct.c b/drivers/usb/serial/kobil_sct.c index 3d2bd65df0f..02c420af251 100644 --- a/drivers/usb/serial/kobil_sct.c +++ b/drivers/usb/serial/kobil_sct.c @@ -335,7 +335,8 @@ static int kobil_write(struct tty_struct *tty, struct usb_serial_port *port, port->interrupt_out_urb->transfer_buffer_length = length; priv->cur_pos = priv->cur_pos + length; - result = usb_submit_urb(port->interrupt_out_urb, GFP_NOIO); + result = usb_submit_urb(port->interrupt_out_urb, + GFP_ATOMIC); dev_dbg(&port->dev, "%s - Send write URB returns: %i\n", __func__, result); todo = priv->filled - priv->cur_pos; @@ -350,7 +351,7 @@ static int kobil_write(struct tty_struct *tty, struct usb_serial_port *port, if (priv->device_type == KOBIL_ADAPTER_B_PRODUCT_ID || priv->device_type == KOBIL_ADAPTER_K_PRODUCT_ID) { result = usb_submit_urb(port->interrupt_in_urb, - GFP_NOIO); + GFP_ATOMIC); dev_dbg(&port->dev, "%s - Send read URB returns: %i\n", __func__, result); } } -- cgit v1.2.3-70-g09d2 From e681286de221af78fc85db9222b6a203148c005a Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 29 Oct 2014 09:07:31 +0100 Subject: USB: opticon: fix non-atomic allocation in write path Write may be called from interrupt context so make sure to use GFP_ATOMIC for all allocations in write. Fixes: 0d930e51cfe6 ("USB: opticon: Add Opticon OPN2001 write support") Cc: stable Signed-off-by: Johan Hovold --- drivers/usb/serial/opticon.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/serial/opticon.c b/drivers/usb/serial/opticon.c index 4856fb7e637..4b7bfb394a3 100644 --- a/drivers/usb/serial/opticon.c +++ b/drivers/usb/serial/opticon.c @@ -215,7 +215,7 @@ static int opticon_write(struct tty_struct *tty, struct usb_serial_port *port, /* The connected devices do not have a bulk write endpoint, * to transmit data to de barcode device the control endpoint is used */ - dr = kmalloc(sizeof(struct usb_ctrlrequest), GFP_NOIO); + dr = kmalloc(sizeof(struct usb_ctrlrequest), GFP_ATOMIC); if (!dr) { count = -ENOMEM; goto error_no_dr; -- cgit v1.2.3-70-g09d2 From 4cdd32b4ba101ae07331f2058b20d7ce0ecc4961 Mon Sep 17 00:00:00 2001 From: Zhangfei Gao Date: Fri, 10 Oct 2014 03:53:47 -0300 Subject: [media] ir-hix5hd2 fix build warning Change CONFIG_PM to CONFIG_PM_SLEEP to solve warning: 'hix5hd2_ir_suspend' & 'hix5hd2_ir_resume' defined but not used Signed-off-by: Zhangfei Gao Signed-off-by: Mauro Carvalho Chehab --- drivers/media/rc/ir-hix5hd2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/rc/ir-hix5hd2.c b/drivers/media/rc/ir-hix5hd2.c index 08bbd4f508c..b0df62961c1 100644 --- a/drivers/media/rc/ir-hix5hd2.c +++ b/drivers/media/rc/ir-hix5hd2.c @@ -297,7 +297,7 @@ static int hix5hd2_ir_remove(struct platform_device *pdev) return 0; } -#ifdef CONFIG_PM +#ifdef CONFIG_PM_SLEEP static int hix5hd2_ir_suspend(struct device *dev) { struct hix5hd2_ir_priv *priv = dev_get_drvdata(dev); -- cgit v1.2.3-70-g09d2 From d358aefdc0cc92b16ced449f998dbad639db6809 Mon Sep 17 00:00:00 2001 From: Ulrich Eckhardt Date: Fri, 10 Oct 2014 13:27:32 -0300 Subject: [media] imon: fix other RC type protocol support With kernel 3.17 the imon remote control for device 15c2:0034 does not work anymore, which uses the OTHER protocol. Only the front panel buttons which uses the RC6 protocol are working. Adds the missing comparison for the RC_BIT_OTHER. Cc: stable@vger.kernel.org # for Kernel 3.17 Signed-off-by: Ulrich Eckhardt Signed-off-by: Mauro Carvalho Chehab --- drivers/media/rc/imon.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/media/rc/imon.c b/drivers/media/rc/imon.c index b8837dd39bb..65f80b8b9f7 100644 --- a/drivers/media/rc/imon.c +++ b/drivers/media/rc/imon.c @@ -1678,7 +1678,8 @@ static void imon_incoming_packet(struct imon_context *ictx, if (press_type == 0) rc_keyup(ictx->rdev); else { - if (ictx->rc_type == RC_BIT_RC6_MCE) + if (ictx->rc_type == RC_BIT_RC6_MCE || + ictx->rc_type == RC_BIT_OTHER) rc_keydown(ictx->rdev, ictx->rc_type == RC_BIT_RC6_MCE ? RC_TYPE_RC6_MCE : RC_TYPE_OTHER, ictx->rc_scancode, ictx->rc_toggle); -- cgit v1.2.3-70-g09d2 From ca0c37a0b489bb14bf3e1549e7a8d0c9a17f4919 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Mon, 3 Nov 2014 15:07:05 +0100 Subject: regulator: max77693: Fix use of uninitialized regulator config Driver allocated on stack struct regulator_config but didn't initialize it fully. Few fields (driver_data, ena_gpio) were left untouched. This lead to using random ena_gpio values as GPIOs for max77693 regulators. On occasion these values could match real GPIO numbers leading to interfering with other drivers and to unsuccessful enable/disable of regulator. Signed-off-by: Krzysztof Kozlowski Fixes: 80b022e29bfd ("regulator: max77693: Add max77693 regualtor driver.") Cc: Signed-off-by: Mark Brown --- drivers/regulator/max77693.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/regulator/max77693.c b/drivers/regulator/max77693.c index c67ff05fc1d..d158f71fa12 100644 --- a/drivers/regulator/max77693.c +++ b/drivers/regulator/max77693.c @@ -227,7 +227,7 @@ static int max77693_pmic_probe(struct platform_device *pdev) struct max77693_dev *iodev = dev_get_drvdata(pdev->dev.parent); struct max77693_regulator_data *rdata = NULL; int num_rdata, i; - struct regulator_config config; + struct regulator_config config = { }; num_rdata = max77693_pmic_init_rdata(&pdev->dev, &rdata); if (!rdata || num_rdata <= 0) { -- cgit v1.2.3-70-g09d2 From d83aef13adfd893694be3f9b7decf167f963aa08 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Mon, 3 Nov 2014 15:40:40 +0100 Subject: regulator: max1586: zero-initialize regulator match table array The struct of_regulator_match rmatch[] is declared as a non-static local variable so the structure members are not auto-initialized. Initialize the array at declaration time to avoid the structure members values to be indeterminate and have sane defaults instead. Signed-off-by: Javier Martinez Canillas Signed-off-by: Mark Brown --- drivers/regulator/max1586.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/regulator/max1586.c b/drivers/regulator/max1586.c index 86db310d530..d2a8c64cae4 100644 --- a/drivers/regulator/max1586.c +++ b/drivers/regulator/max1586.c @@ -163,7 +163,7 @@ static int of_get_max1586_platform_data(struct device *dev, struct max1586_platform_data *pdata) { struct max1586_subdev_data *sub; - struct of_regulator_match rmatch[ARRAY_SIZE(max1586_reg)]; + struct of_regulator_match rmatch[ARRAY_SIZE(max1586_reg)] = { }; struct device_node *np = dev->of_node; int i, matched; -- cgit v1.2.3-70-g09d2 From 050cf85c3f3913fa6cf678bd059a9e0e4c7621e5 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Mon, 3 Nov 2014 15:40:41 +0100 Subject: regulator: max77686: zero-initialize regulator match table The struct of_regulator_match is declared as a non-static local variable so the structure members are not auto-initialized. Initialize the struct at declaration time to avoid the structure members values to be indeterminate and have sane defaults instead. Signed-off-by: Javier Martinez Canillas Signed-off-by: Mark Brown --- drivers/regulator/max77686.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/regulator/max77686.c b/drivers/regulator/max77686.c index ef1af2debbd..f69320e1738 100644 --- a/drivers/regulator/max77686.c +++ b/drivers/regulator/max77686.c @@ -395,7 +395,7 @@ static int max77686_pmic_dt_parse_pdata(struct platform_device *pdev, struct max77686_dev *iodev = dev_get_drvdata(pdev->dev.parent); struct device_node *pmic_np, *regulators_np; struct max77686_regulator_data *rdata; - struct of_regulator_match rmatch; + struct of_regulator_match rmatch = { }; unsigned int i; pmic_np = iodev->dev->of_node; -- cgit v1.2.3-70-g09d2 From ecea7484d2f76da1ce1eacdc7c25df08dab6fe78 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Mon, 3 Nov 2014 15:40:42 +0100 Subject: regulator: max77802: zero-initialize regulator match table The struct of_regulator_match is declared as a non-static local variable so the structure members are not auto-initialized. Initialize the struct at declaration time to avoid the structure members values to be indeterminate and have sane defaults instead. Signed-off-by: Javier Martinez Canillas Signed-off-by: Mark Brown --- drivers/regulator/max77802.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/regulator/max77802.c b/drivers/regulator/max77802.c index d89792b084e..45fa240fe24 100644 --- a/drivers/regulator/max77802.c +++ b/drivers/regulator/max77802.c @@ -454,7 +454,7 @@ static int max77802_pmic_dt_parse_pdata(struct platform_device *pdev, struct max77686_dev *iodev = dev_get_drvdata(pdev->dev.parent); struct device_node *pmic_np, *regulators_np; struct max77686_regulator_data *rdata; - struct of_regulator_match rmatch; + struct of_regulator_match rmatch = { }; unsigned int i; pmic_np = iodev->dev->of_node; -- cgit v1.2.3-70-g09d2 From c9889803e3ba635d4517cb9e366218c9895f8d24 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Mon, 3 Nov 2014 15:40:43 +0100 Subject: regulator: max8660: zero-initialize regulator match table array The struct of_regulator_match rmatch[] is declared as a non-static local variable so the structure members are not auto-initialized. Initialize the array at declaration time to avoid the structure members values to be indeterminate and have sane defaults instead. Signed-off-by: Javier Martinez Canillas Signed-off-by: Mark Brown --- drivers/regulator/max8660.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/regulator/max8660.c b/drivers/regulator/max8660.c index 2fc41118879..7eee2ca1854 100644 --- a/drivers/regulator/max8660.c +++ b/drivers/regulator/max8660.c @@ -335,7 +335,7 @@ static int max8660_pdata_from_dt(struct device *dev, int matched, i; struct device_node *np; struct max8660_subdev_data *sub; - struct of_regulator_match rmatch[ARRAY_SIZE(max8660_reg)]; + struct of_regulator_match rmatch[ARRAY_SIZE(max8660_reg)] = { }; np = of_get_child_by_name(dev->of_node, "regulators"); if (!np) { -- cgit v1.2.3-70-g09d2 From 282179105d5403d991d2510ec74d1031695b3ef0 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Mon, 3 Nov 2014 15:40:44 +0100 Subject: regulator: s2mpa01: zero-initialize regulator match table array The struct of_regulator_match rmatch[] is declared as a non-static local variable so the structure members are not auto-initialized. Initialize the array at declaration time to avoid the structure members values to be indeterminate and have sane defaults instead. Signed-off-by: Javier Martinez Canillas Signed-off-by: Mark Brown --- drivers/regulator/s2mpa01.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/regulator/s2mpa01.c b/drivers/regulator/s2mpa01.c index 4acefa6b462..7633b9bfbe6 100644 --- a/drivers/regulator/s2mpa01.c +++ b/drivers/regulator/s2mpa01.c @@ -341,7 +341,7 @@ static int s2mpa01_pmic_probe(struct platform_device *pdev) { struct sec_pmic_dev *iodev = dev_get_drvdata(pdev->dev.parent); struct sec_platform_data *pdata = dev_get_platdata(iodev->dev); - struct of_regulator_match rdata[S2MPA01_REGULATOR_MAX]; + struct of_regulator_match rdata[S2MPA01_REGULATOR_MAX] = { }; struct device_node *reg_np = NULL; struct regulator_config config = { }; struct s2mpa01_info *s2mpa01; -- cgit v1.2.3-70-g09d2 From cba63cf8f92952211eb13376cda6c05679d675d2 Mon Sep 17 00:00:00 2001 From: Hans Verkuil Date: Mon, 3 Nov 2014 07:42:09 -0300 Subject: [media] vivid: default to single planar device instances The default used to be that the first vivid device instance was single planar, the second multi planar, the third single planar, etc. However, that turned out to be unexpected and awkward. Change the driver to always default to single planar. Signed-off-by: Hans Verkuil Signed-off-by: Mauro Carvalho Chehab --- Documentation/video4linux/vivid.txt | 12 +++++------- drivers/media/platform/vivid/vivid-core.c | 11 +++-------- 2 files changed, 8 insertions(+), 15 deletions(-) diff --git a/Documentation/video4linux/vivid.txt b/Documentation/video4linux/vivid.txt index eeb11a28e4f..e5a940e3d30 100644 --- a/Documentation/video4linux/vivid.txt +++ b/Documentation/video4linux/vivid.txt @@ -221,12 +221,11 @@ ccs_out_mode: specify the allowed video output crop/compose/scaling combination key, not quality. multiplanar: select whether each device instance supports multi-planar formats, - and thus the V4L2 multi-planar API. By default the first device instance - is single-planar, the second multi-planar, and it keeps alternating. + and thus the V4L2 multi-planar API. By default device instances are + single-planar. This module option can override that for each instance. Values are: - 0: use alternating single and multi-planar devices. 1: this is a single-planar instance. 2: this is a multi-planar instance. @@ -975,9 +974,8 @@ is set, then the alpha component is only used for the color red and set to 0 otherwise. The driver has to be configured to support the multiplanar formats. By default -the first driver instance is single-planar, the second is multi-planar, and it -keeps alternating. This can be changed by setting the multiplanar module option, -see section 1 for more details on that option. +the driver instances are single-planar. This can be changed by setting the +multiplanar module option, see section 1 for more details on that option. If the driver instance is using the multiplanar formats/API, then the first single planar format (YUYV) and the multiplanar NV16M and NV61M formats the @@ -1021,7 +1019,7 @@ the output overlay for the video output, turn on video looping and capture to see the blended framebuffer overlay that's being written to by the second instance. This setup would require the following commands: - $ sudo modprobe vivid n_devs=2 node_types=0x10101,0x1 multiplanar=1,1 + $ sudo modprobe vivid n_devs=2 node_types=0x10101,0x1 $ v4l2-ctl -d1 --find-fb /dev/fb1 is the framebuffer associated with base address 0x12800000 $ sudo v4l2-ctl -d2 --set-fbuf fb=1 diff --git a/drivers/media/platform/vivid/vivid-core.c b/drivers/media/platform/vivid/vivid-core.c index 2c61a62ab48..686c3c2ad05 100644 --- a/drivers/media/platform/vivid/vivid-core.c +++ b/drivers/media/platform/vivid/vivid-core.c @@ -100,11 +100,9 @@ MODULE_PARM_DESC(ccs_out_mode, " output crop/compose/scale mode:\n" "\t\t bit 0=crop, 1=compose, 2=scale,\n" "\t\t -1=user-controlled (default)"); -static unsigned multiplanar[VIVID_MAX_DEVS]; +static unsigned multiplanar[VIVID_MAX_DEVS] = { [0 ... (VIVID_MAX_DEVS - 1)] = 1 }; module_param_array(multiplanar, uint, NULL, 0444); -MODULE_PARM_DESC(multiplanar, " 0 (default) is alternating single and multiplanar devices,\n" - "\t\t 1 is single planar devices,\n" - "\t\t 2 is multiplanar devices"); +MODULE_PARM_DESC(multiplanar, " 1 (default) creates a single planar device, 2 creates a multiplanar device."); /* Default: video + vbi-cap (raw and sliced) + radio rx + radio tx + sdr + vbi-out + vid-out */ static unsigned node_types[VIVID_MAX_DEVS] = { [0 ... (VIVID_MAX_DEVS - 1)] = 0x1d3d }; @@ -669,10 +667,7 @@ static int __init vivid_create_instance(int inst) /* start detecting feature set */ /* do we use single- or multi-planar? */ - if (multiplanar[inst] == 0) - dev->multiplanar = inst & 1; - else - dev->multiplanar = multiplanar[inst] > 1; + dev->multiplanar = multiplanar[inst] > 1; v4l2_info(&dev->v4l2_dev, "using %splanar format API\n", dev->multiplanar ? "multi" : "single "); -- cgit v1.2.3-70-g09d2 From 906aaf5a195b59fbafc1a36d06be5a52894904fd Mon Sep 17 00:00:00 2001 From: Akihiro Tsukada Date: Fri, 31 Oct 2014 10:23:18 -0300 Subject: [media] dvb:tc90522: fix stats report * report the fixed per-transponder symbolrate instead of per-TS ones * add output TS-ID report Signed-off-by: Akihiro Tsukada Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb-frontends/tc90522.c | 16 +++++++--------- 1 file changed, 7 insertions(+), 9 deletions(-) diff --git a/drivers/media/dvb-frontends/tc90522.c b/drivers/media/dvb-frontends/tc90522.c index d9905fb52f8..ad3351f233a 100644 --- a/drivers/media/dvb-frontends/tc90522.c +++ b/drivers/media/dvb-frontends/tc90522.c @@ -216,32 +216,30 @@ static int tc90522s_get_frontend(struct dvb_frontend *fe) c->delivery_system = SYS_ISDBS; layers = 0; - ret = reg_read(state, 0xe8, val, 3); + ret = reg_read(state, 0xe6, val, 5); if (ret == 0) { - int slots; u8 v; + c->stream_id = val[0] << 8 | val[1]; + /* high/single layer */ - v = (val[0] & 0x70) >> 4; + v = (val[2] & 0x70) >> 4; c->modulation = (v == 7) ? PSK_8 : QPSK; c->fec_inner = fec_conv_sat[v]; c->layer[0].fec = c->fec_inner; c->layer[0].modulation = c->modulation; - c->layer[0].segment_count = val[1] & 0x3f; /* slots */ + c->layer[0].segment_count = val[3] & 0x3f; /* slots */ /* low layer */ - v = (val[0] & 0x07); + v = (val[2] & 0x07); c->layer[1].fec = fec_conv_sat[v]; if (v == 0) /* no low layer */ c->layer[1].segment_count = 0; else - c->layer[1].segment_count = val[2] & 0x3f; /* slots */ + c->layer[1].segment_count = val[4] & 0x3f; /* slots */ /* actually, BPSK if v==1, but not defined in fe_modulation_t */ c->layer[1].modulation = QPSK; layers = (v > 0) ? 2 : 1; - - slots = c->layer[0].segment_count + c->layer[1].segment_count; - c->symbol_rate = 28860000 * slots / 48; } /* statistics */ -- cgit v1.2.3-70-g09d2 From 8e281fafda676df6f554a9074a28439039005418 Mon Sep 17 00:00:00 2001 From: Akihiro Tsukada Date: Fri, 31 Oct 2014 10:19:39 -0300 Subject: [media] dvb-core: set default properties of ISDB-S Signed-off-by: Akihiro Tsukada Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb-core/dvb_frontend.c | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/drivers/media/dvb-core/dvb_frontend.c b/drivers/media/dvb-core/dvb_frontend.c index b8579ee68bd..2cf30576bf3 100644 --- a/drivers/media/dvb-core/dvb_frontend.c +++ b/drivers/media/dvb-core/dvb_frontend.c @@ -962,6 +962,11 @@ static int dvb_frontend_clear_cache(struct dvb_frontend *fe) case SYS_ATSC: c->modulation = VSB_8; break; + case SYS_ISDBS: + c->symbol_rate = 28860000; + c->rolloff = ROLLOFF_35; + c->bandwidth_hz = c->symbol_rate / 100 * 135; + break; default: c->modulation = QAM_AUTO; break; @@ -2072,6 +2077,7 @@ static int dtv_set_frontend(struct dvb_frontend *fe) break; case SYS_DVBS: case SYS_TURBO: + case SYS_ISDBS: rolloff = 135; break; case SYS_DVBS2: -- cgit v1.2.3-70-g09d2 From 01bd399a10eabddcc57ed489edcdd677a450119c Mon Sep 17 00:00:00 2001 From: Akihiro Tsukada Date: Fri, 31 Oct 2014 10:21:50 -0300 Subject: [media] dvb:tc90522: fix always-false expression Signed-off-by: Akihiro Tsukada Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb-frontends/tc90522.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/media/dvb-frontends/tc90522.c b/drivers/media/dvb-frontends/tc90522.c index ad3351f233a..b35d65c9cc0 100644 --- a/drivers/media/dvb-frontends/tc90522.c +++ b/drivers/media/dvb-frontends/tc90522.c @@ -361,7 +361,7 @@ static int tc90522t_get_frontend(struct dvb_frontend *fe) u8 v; c->isdbt_partial_reception = val[0] & 0x01; - c->isdbt_sb_mode = (val[0] & 0xc0) == 0x01; + c->isdbt_sb_mode = (val[0] & 0xc0) == 0x40; /* layer A */ v = (val[2] & 0x78) >> 3; -- cgit v1.2.3-70-g09d2 From e7dbb48958897c0a80b14250a981a563d9160e4d Mon Sep 17 00:00:00 2001 From: "Steven Rostedt (Red Hat)" Date: Fri, 31 Oct 2014 18:02:05 -0400 Subject: ftracetest: Take the first debugfs mount found Running ftracetests on a box that mounted debugfs in two locations made the ftracetests fail. This is because the tests uses a grep of debugfs from the /proc/mounts file to find the debugfs mount point, and then appends "/tracing" to that string to get the tracing directory. If the debugfs directory is mounted twice, then that grep will return two answers and appending "/tracing" to a string with two lines will not work. Use "head -1" to only take the first mount point found. Acked-by: Masami Hiramatsu Signed-off-by: Steven Rostedt --- tools/testing/selftests/ftrace/ftracetest | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/tools/testing/selftests/ftrace/ftracetest b/tools/testing/selftests/ftrace/ftracetest index a8f81c78285..515247601df 100755 --- a/tools/testing/selftests/ftrace/ftracetest +++ b/tools/testing/selftests/ftrace/ftracetest @@ -82,7 +82,7 @@ parse_opts() { # opts } # Parameters -DEBUGFS_DIR=`grep debugfs /proc/mounts | cut -f2 -d' '` +DEBUGFS_DIR=`grep debugfs /proc/mounts | cut -f2 -d' ' | head -1` TRACING_DIR=$DEBUGFS_DIR/tracing TOP_DIR=`absdir $0` TEST_DIR=$TOP_DIR/test.d -- cgit v1.2.3-70-g09d2 From 167921cb0ff2bdbf25138dad799fec88c99ed316 Mon Sep 17 00:00:00 2001 From: Fengguang Wu Date: Mon, 3 Nov 2014 16:43:32 -0300 Subject: [media] sp2: sp2_init() can be static drivers/media/dvb-frontends/sp2.c:269:5: sparse: symbol 'sp2_init' was not declared. Should it be static? drivers/media/dvb-frontends/sp2.c:351:5: sparse: symbol 'sp2_exit' was not declared. Should it be static? Signed-off-by: Fengguang Wu Signed-off-by: Mauro Carvalho Chehab --- drivers/media/dvb-frontends/sp2.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/media/dvb-frontends/sp2.c b/drivers/media/dvb-frontends/sp2.c index 9b684d5c8f9..15bf4318cb7 100644 --- a/drivers/media/dvb-frontends/sp2.c +++ b/drivers/media/dvb-frontends/sp2.c @@ -266,7 +266,7 @@ int sp2_ci_poll_slot_status(struct dvb_ca_en50221 *en50221, return s->status; } -int sp2_init(struct sp2 *s) +static int sp2_init(struct sp2 *s) { int ret = 0; u8 buf; @@ -348,7 +348,7 @@ err: return ret; } -int sp2_exit(struct i2c_client *client) +static int sp2_exit(struct i2c_client *client) { struct sp2 *s; -- cgit v1.2.3-70-g09d2 From 14015860565a1464193ddb3fbd3f7253a37dfcf9 Mon Sep 17 00:00:00 2001 From: Yao Dongdong Date: Tue, 28 Oct 2014 07:40:25 +0000 Subject: Thermal:Remove usless if(!result) before return tz result is always zero when comes here. Signed-off-by: Yao Dongdong Acked-by: Eduardo Valentin Signed-off-by: Eduardo Valentin --- drivers/thermal/thermal_core.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/thermal/thermal_core.c b/drivers/thermal/thermal_core.c index 9bf10aa6069..43b90709585 100644 --- a/drivers/thermal/thermal_core.c +++ b/drivers/thermal/thermal_core.c @@ -1575,8 +1575,7 @@ struct thermal_zone_device *thermal_zone_device_register(const char *type, thermal_zone_device_update(tz); - if (!result) - return tz; + return tz; unregister: release_idr(&thermal_tz_idr, &thermal_idr_lock, tz->id); -- cgit v1.2.3-70-g09d2 From cf84a691a61606a2e7269907d3727e2d9fa148ee Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Mon, 27 Oct 2014 18:34:33 +0100 Subject: USB: cdc-acm: add device id for GW Instek AFG-2225 Add device-id entry for GW Instek AFG-2225, which has a byte swapped bInterfaceSubClass (0x20). Reported-by: Karl Palsson Cc: stable Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index e934e19f49f..959343b891c 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -1681,6 +1681,7 @@ static const struct usb_device_id acm_ids[] = { { USB_DEVICE(0x0572, 0x1328), /* Shiro / Aztech USB MODEM UM-3100 */ .driver_info = NO_UNION_NORMAL, /* has no union descriptor */ }, + { USB_DEVICE(0x2184, 0x001c) }, /* GW Instek AFG-2225 */ { USB_DEVICE(0x22b8, 0x6425), /* Motorola MOTOMAGX phones */ }, /* Motorola H24 HSPA module: */ -- cgit v1.2.3-70-g09d2 From 24cb4502c97b0c9bed90aae0225adb92088783d3 Mon Sep 17 00:00:00 2001 From: Jim Paris Date: Thu, 30 Oct 2014 11:04:47 -0400 Subject: cdc-acm: ensure that termios get set when the port is activated The driver wasn't properly configuring the hardware for the current termios settings under all conditions. Ensure that termios are written to the device when the port is activated. Signed-off-by: Jim Paris Reviewed-by: Johan Hovold Acked-by: Oliver Neukum Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index 959343b891c..6771f884cb8 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -60,6 +60,9 @@ static struct acm *acm_table[ACM_TTY_MINORS]; static DEFINE_MUTEX(acm_table_lock); +static void acm_tty_set_termios(struct tty_struct *tty, + struct ktermios *termios_old); + /* * acm_table accessors */ @@ -554,6 +557,8 @@ static int acm_port_activate(struct tty_port *port, struct tty_struct *tty) goto error_submit_urb; } + acm_tty_set_termios(tty, NULL); + /* * Unthrottle device in case the TTY was closed while throttled. */ -- cgit v1.2.3-70-g09d2 From 90a646c770c50cc206ceba0d7b50453c46c13c36 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Wed, 1 Oct 2014 11:29:14 +0200 Subject: usb: Do not allow usb_alloc_streams on unconfigured devices This commit fixes the following oops: [10238.622067] scsi host3: uas_eh_bus_reset_handler start [10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd [10245.779365] usb 3-4: device descriptor read/8, error -110 [10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd [10250.897603] usb 3-4: device descriptor read/8, error -110 [10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040 [10251.058244] IP: [] xhci_check_streams_endpoint+0x91/0x140 [10251.059473] Call Trace: [10251.059487] [] xhci_calculate_streams_and_bitmask+0xbc/0x130 [10251.059520] [] xhci_alloc_streams+0x10f/0x5a0 [10251.059548] [] ? check_preempt_curr+0x75/0xa0 [10251.059575] [] ? ttwu_do_wakeup+0x2c/0x100 [10251.059601] [] ? ttwu_do_activate.constprop.111+0x66/0x70 [10251.059635] [] usb_alloc_streams+0xab/0xf0 [10251.059662] [] uas_configure_endpoints+0x128/0x150 [uas] [10251.059694] [] uas_post_reset+0x3c/0xb0 [uas] [10251.059722] [] usb_reset_device+0x1b9/0x2a0 [10251.059749] [] uas_eh_bus_reset_handler+0xb2/0x190 [uas] [10251.059781] [] scsi_try_bus_reset+0x53/0x110 [10251.059808] [] scsi_eh_bus_reset+0xf7/0x270 The problem is the following call sequence (simplified): 1) usb_reset_device 2) usb_reset_and_verify_device 2) hub_port_init 3) hub_port_finish_reset 3) xhci_discover_or_reset_device This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0 4) usb_get_device_descriptor This fails 5) hub_port_init fails 6) usb_reset_and_verify_device fails, does not restore device config 7) uas_post_reset 8) xhci_alloc_streams NULL deref on the free-ed ring This commit fixes this by not allowing usb_alloc_streams to continue if the device is not configured. Note that we do allow usb_free_streams to continue after a (logical) disconnect, as it is necessary to explicitly free the streams at the xhci controller level. Cc: stable@vger.kernel.org Signed-off-by: Hans de Goede Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/hcd.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/core/hcd.c b/drivers/usb/core/hcd.c index b84fb141e12..a6efb4184f2 100644 --- a/drivers/usb/core/hcd.c +++ b/drivers/usb/core/hcd.c @@ -2060,6 +2060,8 @@ int usb_alloc_streams(struct usb_interface *interface, return -EINVAL; if (dev->speed != USB_SPEED_SUPER) return -EINVAL; + if (dev->state < USB_STATE_CONFIGURED) + return -ENODEV; for (i = 0; i < num_eps; i++) { /* Streams only apply to bulk endpoints. */ -- cgit v1.2.3-70-g09d2 From 93c9bf4d1838d5851a18ca398b0ad66397f05056 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Fri, 31 Oct 2014 14:49:47 -0400 Subject: usb-storage: handle a skipped data phase Sometimes mass-storage devices using the Bulk-only transport will mistakenly skip the data phase of a command. Rather than sending the data expected by the host or sending a zero-length packet, they go directly to the status phase and send the CSW. This causes problems for usb-storage, for obvious reasons. The driver will interpret the CSW as a short data transfer and will wait to receive a CSW. The device won't have anything left to send, so the command eventually times out. The SCSI layer doesn't retry commands after they time out (this is a relatively recent change). Therefore we should do our best to detect a skipped data phase and handle it promptly. This patch adds code to do that. If usb-storage receives a short 13-byte data transfer from the device, and if the first four bytes of the data match the CSW signature, the driver will set the residue to the full transfer length and interpret the data as a CSW. This fixes Bugzilla #86611. Signed-off-by: Alan Stern CC: Matthew Dharm Tested-by: Paul Osmialowski CC: Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/transport.c | 26 ++++++++++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/drivers/usb/storage/transport.c b/drivers/usb/storage/transport.c index 22c7d4360fa..b1d815eb6d0 100644 --- a/drivers/usb/storage/transport.c +++ b/drivers/usb/storage/transport.c @@ -1118,6 +1118,31 @@ int usb_stor_Bulk_transport(struct scsi_cmnd *srb, struct us_data *us) */ if (result == USB_STOR_XFER_LONG) fake_sense = 1; + + /* + * Sometimes a device will mistakenly skip the data phase + * and go directly to the status phase without sending a + * zero-length packet. If we get a 13-byte response here, + * check whether it really is a CSW. + */ + if (result == USB_STOR_XFER_SHORT && + srb->sc_data_direction == DMA_FROM_DEVICE && + transfer_length - scsi_get_resid(srb) == + US_BULK_CS_WRAP_LEN) { + struct scatterlist *sg = NULL; + unsigned int offset = 0; + + if (usb_stor_access_xfer_buf((unsigned char *) bcs, + US_BULK_CS_WRAP_LEN, srb, &sg, + &offset, FROM_XFER_BUF) == + US_BULK_CS_WRAP_LEN && + bcs->Signature == + cpu_to_le32(US_BULK_CS_SIGN)) { + usb_stor_dbg(us, "Device skipped data phase\n"); + scsi_set_resid(srb, transfer_length); + goto skipped_data_phase; + } + } } /* See flow chart on pg 15 of the Bulk Only Transport spec for @@ -1153,6 +1178,7 @@ int usb_stor_Bulk_transport(struct scsi_cmnd *srb, struct us_data *us) if (result != USB_STOR_XFER_GOOD) return USB_STOR_TRANSPORT_ERROR; + skipped_data_phase: /* check bulk status */ residue = le32_to_cpu(bcs->Residue); usb_stor_dbg(us, "Bulk Status S 0x%x T 0x%x R %u Stat 0x%x\n", -- cgit v1.2.3-70-g09d2 From aee0ce3ae73c566ace9958302e001d3cbbb0a623 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Fri, 31 Oct 2014 14:37:32 +0100 Subject: uas: Add US_FL_NO_ATA_1X quirk for 1 more Seagate model These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X quirk to filter these out. Cc: stable@vger.kernel.org # 3.16 Signed-off-by: Hans de Goede Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_uas.h | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/usb/storage/unusual_uas.h b/drivers/usb/storage/unusual_uas.h index 8511b54a65d..d57e138567a 100644 --- a/drivers/usb/storage/unusual_uas.h +++ b/drivers/usb/storage/unusual_uas.h @@ -61,6 +61,13 @@ UNUSUAL_DEV(0x0bc2, 0xab20, 0x0000, 0x9999, USB_SC_DEVICE, USB_PR_DEVICE, NULL, US_FL_NO_ATA_1X), +/* https://bbs.archlinux.org/viewtopic.php?id=183190 */ +UNUSUAL_DEV(0x0bc2, 0xab21, 0x0000, 0x9999, + "Seagate", + "Backup+ BK", + USB_SC_DEVICE, USB_PR_DEVICE, NULL, + US_FL_NO_ATA_1X), + /* Reported-by: Claudio Bizzarri */ UNUSUAL_DEV(0x152d, 0x0567, 0x0000, 0x9999, "JMicron", -- cgit v1.2.3-70-g09d2 From cee2448e5b412ea109e92be12cd504df28ab1e0f Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Wed, 29 Oct 2014 11:46:11 +0300 Subject: USB: HWA: fix a warning message We wanted to print the version as (major).(minor) but because the shift operation is higher precedence than the mask then we print (minor).(minor). Signed-off-by: Dan Carpenter Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/hwa-hc.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/host/hwa-hc.c b/drivers/usb/host/hwa-hc.c index d0d8fadf706..1db0626c8bf 100644 --- a/drivers/usb/host/hwa-hc.c +++ b/drivers/usb/host/hwa-hc.c @@ -607,7 +607,7 @@ found: wa->wa_descr = wa_descr = (struct usb_wa_descriptor *) hdr; if (le16_to_cpu(wa_descr->bcdWAVersion) > 0x0100) dev_warn(dev, "Wire Adapter v%d.%d newer than groked v1.0\n", - le16_to_cpu(wa_descr->bcdWAVersion) & 0xff00 >> 8, + (le16_to_cpu(wa_descr->bcdWAVersion) & 0xff00) >> 8, le16_to_cpu(wa_descr->bcdWAVersion) & 0x00ff); result = 0; error: -- cgit v1.2.3-70-g09d2 From 2391eacbd00b706ff4902db7dbee21e33b6f1850 Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Tue, 28 Oct 2014 11:05:29 +0100 Subject: xhci: Disable streams on Asmedia 1042 xhci controllers Streams seem to be broken on the Asmedia 1042. An uas capable Seagate disk which is known to work fine with other controllers causes the system to freeze when connected over usb-3 with this controller, where as it works fine with uas in usb-2 ports, indicating a problem with streams. This is a bit bigger hammer then I would like to use for this, but for now it will have to make do. I've ordered a pci-e usb controller card with an Asmedia 1042, once that arrives I'll try to get streams to work (with a quirk flag if necessary) and then we can re-enable them. For now this at least makes uas capable disk enclosures work again by forcing fallback to the usb-storage driver. Reported-by: Bogdan Mihalcea Cc: Bogdan Mihalcea Cc: stable@vger.kernel.org # 3.16 Signed-off-by: Hans de Goede Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-pci.c | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index 280dde93abe..2c7f3fb811d 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -162,6 +162,10 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) pdev->device == 0x3432) xhci->quirks |= XHCI_BROKEN_STREAMS; + if (pdev->vendor == PCI_VENDOR_ID_ASMEDIA && + pdev->device == 0x1042) + xhci->quirks |= XHCI_BROKEN_STREAMS; + if (xhci->quirks & XHCI_RESET_ON_RESUME) xhci_dbg_trace(xhci, trace_xhci_dbg_quirks, "QUIRK: Resetting on resume"); -- cgit v1.2.3-70-g09d2 From 673029fe9c16c95600bdaca4760673527af32edf Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Thu, 9 Oct 2014 17:27:56 +0200 Subject: uas: Add NO_ATA_1X for VIA VL711 devices Just like some Seagate enclosures, these devices do not seem to grok ata pass through commands. Cc: stable@vger.kernel.org # 3.16 Signed-off-by: Hans de Goede Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_uas.h | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/usb/storage/unusual_uas.h b/drivers/usb/storage/unusual_uas.h index d57e138567a..ea793c1f304 100644 --- a/drivers/usb/storage/unusual_uas.h +++ b/drivers/usb/storage/unusual_uas.h @@ -82,3 +82,10 @@ UNUSUAL_DEV(0x174c, 0x5106, 0x0000, 0x9999, "ASM1051", USB_SC_DEVICE, USB_PR_DEVICE, NULL, US_FL_IGNORE_UAS), + +/* Reported-by: Hans de Goede */ +UNUSUAL_DEV(0x2109, 0x0711, 0x0000, 0x9999, + "VIA", + "VL711", + USB_SC_DEVICE, USB_PR_DEVICE, NULL, + US_FL_NO_ATA_1X), -- cgit v1.2.3-70-g09d2 From cd6e245a2d061a8367e37aaece32cf3fc922de80 Mon Sep 17 00:00:00 2001 From: Sylwester Nawrocki Date: Tue, 7 Oct 2014 11:12:07 +0200 Subject: usb: Remove references to non-existent PLAT_S5P symbol The PLAT_S5P Kconfig symbol was removed in commit d78c16ccde96 ("ARM: SAMSUNG: Remove remaining legacy code"). There are still some references left, fix that by replacing them with ARCH_S5PV210. Fixes: d78c16ccde96 ("ARM: SAMSUNG: Remove remaining legacy code") Reported-by: Paul Bolle Acked-by: Jingoo Han Signed-off-by: Sylwester Nawrocki Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/Kconfig | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index a8a30b1d416..a3ca1375dd5 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -234,7 +234,7 @@ config USB_EHCI_SH config USB_EHCI_EXYNOS tristate "EHCI support for Samsung S5P/EXYNOS SoC Series" - depends on PLAT_S5P || ARCH_EXYNOS + depends on ARCH_S5PV210 || ARCH_EXYNOS help Enable support for the Samsung Exynos SOC's on-chip EHCI controller. @@ -550,7 +550,7 @@ config USB_OHCI_SH config USB_OHCI_EXYNOS tristate "OHCI support for Samsung S5P/EXYNOS SoC Series" - depends on PLAT_S5P || ARCH_EXYNOS + depends on ARCH_S5PV210 || ARCH_EXYNOS help Enable support for the Samsung Exynos SOC's on-chip OHCI controller. -- cgit v1.2.3-70-g09d2 From ec5633ba677761b44ba94ae29c906ba79dd6eaa0 Mon Sep 17 00:00:00 2001 From: Luis Henriques Date: Thu, 2 Oct 2014 00:10:57 +0100 Subject: usb: storage: fix build warnings !CONFIG_PM Functions fw5895_init() and config_autodelink_before_power_down() are used only when CONFIG_PM is defined. drivers/usb/storage/realtek_cr.c:699:13: warning: 'fw5895_init' defined but not used [-Wunused-function] drivers/usb/storage/realtek_cr.c:629:12: warning: 'config_autodelink_before_power_down' defined but not used [-Wunused-function] Signed-off-by: Luis Henriques Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/realtek_cr.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/storage/realtek_cr.c b/drivers/usb/storage/realtek_cr.c index 8591d89a38e..27e4a580d2e 100644 --- a/drivers/usb/storage/realtek_cr.c +++ b/drivers/usb/storage/realtek_cr.c @@ -626,6 +626,7 @@ static int config_autodelink_after_power_on(struct us_data *us) return 0; } +#ifdef CONFIG_PM static int config_autodelink_before_power_down(struct us_data *us) { struct rts51x_chip *chip = (struct rts51x_chip *)(us->extra); @@ -716,6 +717,7 @@ static void fw5895_init(struct us_data *us) } } } +#endif #ifdef CONFIG_REALTEK_AUTOPM static void fw5895_set_mmc_wp(struct us_data *us) -- cgit v1.2.3-70-g09d2 From 2e069232fd470175068cbd6eaf8879ef47d772f8 Mon Sep 17 00:00:00 2001 From: Mark Einon Date: Sun, 19 Oct 2014 20:25:26 +0100 Subject: MAINTAINERS: Remove duplicate entry for usbip driver The usbip driver was moved out of staging in 3.17-rc3 but the MAINTAINERS file still has the old staging entry as well as the new one. Remove the old entry. Signed-off-by: Mark Einon Signed-off-by: Greg Kroah-Hartman --- MAINTAINERS | 5 ----- 1 file changed, 5 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index 3c6427190be..22d0bb08127 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -9703,11 +9703,6 @@ S: Maintained F: Documentation/hid/hiddev.txt F: drivers/hid/usbhid/ -USB/IP DRIVERS -L: linux-usb@vger.kernel.org -S: Orphan -F: drivers/staging/usbip/ - USB ISP116X DRIVER M: Olav Kongas L: linux-usb@vger.kernel.org -- cgit v1.2.3-70-g09d2 From 876af5d454548be40327ba9efea4bc92a8575019 Mon Sep 17 00:00:00 2001 From: Adel Gadllah Date: Thu, 9 Oct 2014 09:29:29 +0200 Subject: USB: quirks: enable device-qualifier quirk for another Elan touchscreen Currently this quirk is enabled for the model with the device id 0x0089, it is needed for the 0x009b model, which is found on the Fujitsu Lifebook u904 as well. Signed-off-by: Adel Gadllah Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/quirks.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/usb/core/quirks.c b/drivers/usb/core/quirks.c index 5ae883dc21f..d1080ed3608 100644 --- a/drivers/usb/core/quirks.c +++ b/drivers/usb/core/quirks.c @@ -97,6 +97,9 @@ static const struct usb_device_id usb_quirk_list[] = { { USB_DEVICE(0x04f3, 0x0089), .driver_info = USB_QUIRK_DEVICE_QUALIFIER }, + { USB_DEVICE(0x04f3, 0x009b), .driver_info = + USB_QUIRK_DEVICE_QUALIFIER }, + /* Roland SC-8820 */ { USB_DEVICE(0x0582, 0x0007), .driver_info = USB_QUIRK_RESET_RESUME }, -- cgit v1.2.3-70-g09d2 From d749947561af5996ccc076b2ffcc5f48b1be5d74 Mon Sep 17 00:00:00 2001 From: Adel Gadllah Date: Thu, 9 Oct 2014 09:29:30 +0200 Subject: USB: quirks: enable device-qualifier quirk for yet another Elan touchscreen Yet another device affected by this. Tested-by: Kevin Fenzi Signed-off-by: Adel Gadllah Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/quirks.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/usb/core/quirks.c b/drivers/usb/core/quirks.c index d1080ed3608..39b4081b632 100644 --- a/drivers/usb/core/quirks.c +++ b/drivers/usb/core/quirks.c @@ -100,6 +100,9 @@ static const struct usb_device_id usb_quirk_list[] = { { USB_DEVICE(0x04f3, 0x009b), .driver_info = USB_QUIRK_DEVICE_QUALIFIER }, + { USB_DEVICE(0x04f3, 0x016f), .driver_info = + USB_QUIRK_DEVICE_QUALIFIER }, + /* Roland SC-8820 */ { USB_DEVICE(0x0582, 0x0007), .driver_info = USB_QUIRK_RESET_RESUME }, -- cgit v1.2.3-70-g09d2 From b45abacde3d551c6696c6738bef4a1805d0bf27a Mon Sep 17 00:00:00 2001 From: Oliver Neukum Date: Mon, 27 Oct 2014 14:53:29 +0100 Subject: xhci: no switching back on non-ULT Haswell The switch back is limited to ULT even on HP. The contrary finding arose by bad luck in BIOS versions for testing. This fixes spontaneous resume from S3 on some HP laptops. Signed-off-by: Oliver Neukum Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/xhci-pci.c | 14 -------------- 1 file changed, 14 deletions(-) diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c index 2c7f3fb811d..9a69b1f1b30 100644 --- a/drivers/usb/host/xhci-pci.c +++ b/drivers/usb/host/xhci-pci.c @@ -127,20 +127,6 @@ static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci) xhci->quirks |= XHCI_SPURIOUS_REBOOT; xhci->quirks |= XHCI_AVOID_BEI; } - if (pdev->vendor == PCI_VENDOR_ID_INTEL && - (pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI || - pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI)) { - /* Workaround for occasional spurious wakeups from S5 (or - * any other sleep) on Haswell machines with LPT and LPT-LP - * with the new Intel BIOS - */ - /* Limit the quirk to only known vendors, as this triggers - * yet another BIOS bug on some other machines - * https://bugzilla.kernel.org/show_bug.cgi?id=66171 - */ - if (pdev->subsystem_vendor == PCI_VENDOR_ID_HP) - xhci->quirks |= XHCI_SPURIOUS_WAKEUP; - } if (pdev->vendor == PCI_VENDOR_ID_INTEL && pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI) { xhci->quirks |= XHCI_SPURIOUS_REBOOT; -- cgit v1.2.3-70-g09d2 From d1d9548256fbdf2e049d6413a5266c41e73658ee Mon Sep 17 00:00:00 2001 From: Hans de Goede Date: Thu, 23 Oct 2014 14:40:57 +0200 Subject: uas: Add US_FL_NO_ATA_1X quirk for 2 more Seagate models These drives hang when receiving ATA12 commands, so set the US_FL_NO_ATA_1X quirk to filter these out. Cc: stable@vger.kernel.org # 3.16 Signed-off-by: Hans de Goede Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_uas.h | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/drivers/usb/storage/unusual_uas.h b/drivers/usb/storage/unusual_uas.h index ea793c1f304..2fefaf923e4 100644 --- a/drivers/usb/storage/unusual_uas.h +++ b/drivers/usb/storage/unusual_uas.h @@ -54,6 +54,20 @@ UNUSUAL_DEV(0x0bc2, 0x3312, 0x0000, 0x9999, USB_SC_DEVICE, USB_PR_DEVICE, NULL, US_FL_NO_ATA_1X), +/* Reported-by: Hans de Goede */ +UNUSUAL_DEV(0x0bc2, 0x3320, 0x0000, 0x9999, + "Seagate", + "Expansion Desk", + USB_SC_DEVICE, USB_PR_DEVICE, NULL, + US_FL_NO_ATA_1X), + +/* Reported-by: Bogdan Mihalcea */ +UNUSUAL_DEV(0x0bc2, 0xa003, 0x0000, 0x9999, + "Seagate", + "Backup Plus", + USB_SC_DEVICE, USB_PR_DEVICE, NULL, + US_FL_NO_ATA_1X), + /* https://bbs.archlinux.org/viewtopic.php?id=183190 */ UNUSUAL_DEV(0x0bc2, 0xab20, 0x0000, 0x9999, "Seagate", -- cgit v1.2.3-70-g09d2 From 01ed67dc70834d00d62b6e754ee0f76301fbc140 Mon Sep 17 00:00:00 2001 From: Tony Zheng Date: Fri, 17 Oct 2014 19:43:02 +0800 Subject: usb: core: need to call usb_phy_notify_connect after device setup Since we notify disconnecting based on the usb device is existed (port_dev->child, the child device at roothub is not NULL), we need to notify connect after device has been registered. This fixes a bug that do fast plug in/out test, and the notify_disconnect is not called due to roothub child is NULL and the enumeration has failed. Cc: v3.17+ Signed-off-by: Tony Zheng Signed-off-by: Peter Chen Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/hub.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 11e80ac3132..65a8e505588 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -4468,9 +4468,6 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1, if (retval) goto fail; - if (hcd->usb_phy && !hdev->parent) - usb_phy_notify_connect(hcd->usb_phy, udev->speed); - /* * Some superspeed devices have finished the link training process * and attached to a superspeed hub port, but the device descriptor @@ -4783,6 +4780,10 @@ static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus, port_dev->child = NULL; spin_unlock_irq(&device_state_lock); mutex_unlock(&usb_port_peer_mutex); + } else { + if (hcd->usb_phy && !hdev->parent) + usb_phy_notify_connect(hcd->usb_phy, + udev->speed); } } -- cgit v1.2.3-70-g09d2 From b2108f1e519e983e5dd5712b3a44f7366ab509e4 Mon Sep 17 00:00:00 2001 From: Peter Chen Date: Tue, 4 Nov 2014 11:14:31 +0800 Subject: usb: core: notify disconnection when core detects disconnect It is safe to call notify disconnect when the usb core thinks the device is disconnected. This commit also fixes one bug found at below situation: we have not enabled usb wakeup, we do system suspend when there is an usb device at the port, after suspend, we plug out the usb device, then plug in device again. At that time, the nofity disconnect was not called at current code, as the controller doesn't know the usb device was disconnected during the suspend, but USB core knows the port has changed during that periods. So to fix this problem, and let the usb core call notify disconnect. Cc: 3.17+ Signed-off-by: Peter Chen Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/hub.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index 65a8e505588..b649fef2e35 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -4624,8 +4624,7 @@ static void hub_port_connect(struct usb_hub *hub, int port1, u16 portstatus, /* Disconnect any existing devices under this port */ if (udev) { - if (hcd->usb_phy && !hdev->parent && - !(portstatus & USB_PORT_STAT_CONNECTION)) + if (hcd->usb_phy && !hdev->parent) usb_phy_notify_disconnect(hcd->usb_phy, udev->speed); usb_disconnect(&port_dev->child); } -- cgit v1.2.3-70-g09d2 From c72c553249bb73705f594e292a8f8750027fbcbe Mon Sep 17 00:00:00 2001 From: Stefan Agner Date: Mon, 27 Oct 2014 17:40:44 +0100 Subject: ARM: imx: clk-vf610: define PLL's clock tree So far, the required PLL's (PLL1/PLL2/PLL5) have been initialized by boot loader and the kernel code defined fixed rates according to those default configurations. Beginning with the USB PLL7 the code started to initialize the PLL's itself (using imx_clk_pllv3). However, since commit dc4805c2e78ba5a22ea1632f3e3e4ee601a1743b (ARM: imx: remove ENABLE and BYPASS bits from clk-pllv3 driver) imx_clk_pllv3 no longer takes care of the ENABLE and BYPASS bits, hence the USB PLL were not configured correctly anymore. This patch not only fixes those USB PLL's, but also makes use of the imx_clk_pllv3 for all PLL's and alignes the code with the PLL support of the i.MX6 series. Signed-off-by: Stefan Agner Signed-off-by: Shawn Guo --- arch/arm/mach-imx/clk-vf610.c | 134 ++++++++++++++++++++++---------- include/dt-bindings/clock/vf610-clock.h | 39 ++++++++-- 2 files changed, 123 insertions(+), 50 deletions(-) diff --git a/arch/arm/mach-imx/clk-vf610.c b/arch/arm/mach-imx/clk-vf610.c index a1781847505..40963725459 100644 --- a/arch/arm/mach-imx/clk-vf610.c +++ b/arch/arm/mach-imx/clk-vf610.c @@ -58,8 +58,14 @@ #define PFD_PLL1_BASE (anatop_base + 0x2b0) #define PFD_PLL2_BASE (anatop_base + 0x100) #define PFD_PLL3_BASE (anatop_base + 0xf0) +#define PLL1_CTRL (anatop_base + 0x270) +#define PLL2_CTRL (anatop_base + 0x30) #define PLL3_CTRL (anatop_base + 0x10) +#define PLL4_CTRL (anatop_base + 0x70) +#define PLL5_CTRL (anatop_base + 0xe0) +#define PLL6_CTRL (anatop_base + 0xa0) #define PLL7_CTRL (anatop_base + 0x20) +#define ANA_MISC1 (anatop_base + 0x160) static void __iomem *anatop_base; static void __iomem *ccm_base; @@ -67,25 +73,34 @@ static void __iomem *ccm_base; /* sources for multiplexer clocks, this is used multiple times */ static const char *fast_sels[] = { "firc", "fxosc", }; static const char *slow_sels[] = { "sirc_32k", "sxosc", }; -static const char *pll1_sels[] = { "pll1_main", "pll1_pfd1", "pll1_pfd2", "pll1_pfd3", "pll1_pfd4", }; -static const char *pll2_sels[] = { "pll2_main", "pll2_pfd1", "pll2_pfd2", "pll2_pfd3", "pll2_pfd4", }; -static const char *sys_sels[] = { "fast_clk_sel", "slow_clk_sel", "pll2_pfd_sel", "pll2_main", "pll1_pfd_sel", "pll3_main", }; +static const char *pll1_sels[] = { "pll1_sys", "pll1_pfd1", "pll1_pfd2", "pll1_pfd3", "pll1_pfd4", }; +static const char *pll2_sels[] = { "pll2_bus", "pll2_pfd1", "pll2_pfd2", "pll2_pfd3", "pll2_pfd4", }; +static const char *pll_bypass_src_sels[] = { "fast_clk_sel", "lvds1_in", }; +static const char *pll1_bypass_sels[] = { "pll1", "pll1_bypass_src", }; +static const char *pll2_bypass_sels[] = { "pll2", "pll2_bypass_src", }; +static const char *pll3_bypass_sels[] = { "pll3", "pll3_bypass_src", }; +static const char *pll4_bypass_sels[] = { "pll4", "pll4_bypass_src", }; +static const char *pll5_bypass_sels[] = { "pll5", "pll5_bypass_src", }; +static const char *pll6_bypass_sels[] = { "pll6", "pll6_bypass_src", }; +static const char *pll7_bypass_sels[] = { "pll7", "pll7_bypass_src", }; +static const char *sys_sels[] = { "fast_clk_sel", "slow_clk_sel", "pll2_pfd_sel", "pll2_bus", "pll1_pfd_sel", "pll3_usb_otg", }; static const char *ddr_sels[] = { "pll2_pfd2", "sys_sel", }; static const char *rmii_sels[] = { "enet_ext", "audio_ext", "enet_50m", "enet_25m", }; static const char *enet_ts_sels[] = { "enet_ext", "fxosc", "audio_ext", "usb", "enet_ts", "enet_25m", "enet_50m", }; -static const char *esai_sels[] = { "audio_ext", "mlb", "spdif_rx", "pll4_main_div", }; -static const char *sai_sels[] = { "audio_ext", "mlb", "spdif_rx", "pll4_main_div", }; +static const char *esai_sels[] = { "audio_ext", "mlb", "spdif_rx", "pll4_audio_div", }; +static const char *sai_sels[] = { "audio_ext", "mlb", "spdif_rx", "pll4_audio_div", }; static const char *nfc_sels[] = { "platform_bus", "pll1_pfd1", "pll3_pfd1", "pll3_pfd3", }; -static const char *qspi_sels[] = { "pll3_main", "pll3_pfd4", "pll2_pfd4", "pll1_pfd4", }; -static const char *esdhc_sels[] = { "pll3_main", "pll3_pfd3", "pll1_pfd3", "platform_bus", }; -static const char *dcu_sels[] = { "pll1_pfd2", "pll3_main", }; +static const char *qspi_sels[] = { "pll3_usb_otg", "pll3_pfd4", "pll2_pfd4", "pll1_pfd4", }; +static const char *esdhc_sels[] = { "pll3_usb_otg", "pll3_pfd3", "pll1_pfd3", "platform_bus", }; +static const char *dcu_sels[] = { "pll1_pfd2", "pll3_usb_otg", }; static const char *gpu_sels[] = { "pll2_pfd2", "pll3_pfd2", }; -static const char *vadc_sels[] = { "pll6_main_div", "pll3_main_div", "pll3_main", }; +static const char *vadc_sels[] = { "pll6_video_div", "pll3_usb_otg_div", "pll3_usb_otg", }; /* FTM counter clock source, not module clock */ static const char *ftm_ext_sels[] = {"sirc_128k", "sxosc", "fxosc_half", "audio_ext", }; static const char *ftm_fix_sels[] = { "sxosc", "ipg_bus", }; -static struct clk_div_table pll4_main_div_table[] = { + +static struct clk_div_table pll4_audio_div_table[] = { { .val = 0, .div = 1 }, { .val = 1, .div = 2 }, { .val = 2, .div = 6 }, @@ -120,6 +135,9 @@ static void __init vf610_clocks_init(struct device_node *ccm_node) clk[VF610_CLK_AUDIO_EXT] = imx_obtain_fixed_clock("audio_ext", 0); clk[VF610_CLK_ENET_EXT] = imx_obtain_fixed_clock("enet_ext", 0); + /* Clock source from external clock via LVDs PAD */ + clk[VF610_CLK_ANACLK1] = imx_obtain_fixed_clock("anaclk1", 0); + clk[VF610_CLK_FXOSC_HALF] = imx_clk_fixed_factor("fxosc_half", "fxosc", 1, 2); np = of_find_compatible_node(NULL, NULL, "fsl,vf610-anatop"); @@ -133,31 +151,63 @@ static void __init vf610_clocks_init(struct device_node *ccm_node) clk[VF610_CLK_SLOW_CLK_SEL] = imx_clk_mux("slow_clk_sel", CCM_CCSR, 4, 1, slow_sels, ARRAY_SIZE(slow_sels)); clk[VF610_CLK_FASK_CLK_SEL] = imx_clk_mux("fast_clk_sel", CCM_CCSR, 5, 1, fast_sels, ARRAY_SIZE(fast_sels)); - clk[VF610_CLK_PLL1_MAIN] = imx_clk_fixed_factor("pll1_main", "fast_clk_sel", 22, 1); - clk[VF610_CLK_PLL1_PFD1] = imx_clk_pfd("pll1_pfd1", "pll1_main", PFD_PLL1_BASE, 0); - clk[VF610_CLK_PLL1_PFD2] = imx_clk_pfd("pll1_pfd2", "pll1_main", PFD_PLL1_BASE, 1); - clk[VF610_CLK_PLL1_PFD3] = imx_clk_pfd("pll1_pfd3", "pll1_main", PFD_PLL1_BASE, 2); - clk[VF610_CLK_PLL1_PFD4] = imx_clk_pfd("pll1_pfd4", "pll1_main", PFD_PLL1_BASE, 3); - - clk[VF610_CLK_PLL2_MAIN] = imx_clk_fixed_factor("pll2_main", "fast_clk_sel", 22, 1); - clk[VF610_CLK_PLL2_PFD1] = imx_clk_pfd("pll2_pfd1", "pll2_main", PFD_PLL2_BASE, 0); - clk[VF610_CLK_PLL2_PFD2] = imx_clk_pfd("pll2_pfd2", "pll2_main", PFD_PLL2_BASE, 1); - clk[VF610_CLK_PLL2_PFD3] = imx_clk_pfd("pll2_pfd3", "pll2_main", PFD_PLL2_BASE, 2); - clk[VF610_CLK_PLL2_PFD4] = imx_clk_pfd("pll2_pfd4", "pll2_main", PFD_PLL2_BASE, 3); - - clk[VF610_CLK_PLL3_MAIN] = imx_clk_fixed_factor("pll3_main", "fast_clk_sel", 20, 1); - clk[VF610_CLK_PLL3_PFD1] = imx_clk_pfd("pll3_pfd1", "pll3_main", PFD_PLL3_BASE, 0); - clk[VF610_CLK_PLL3_PFD2] = imx_clk_pfd("pll3_pfd2", "pll3_main", PFD_PLL3_BASE, 1); - clk[VF610_CLK_PLL3_PFD3] = imx_clk_pfd("pll3_pfd3", "pll3_main", PFD_PLL3_BASE, 2); - clk[VF610_CLK_PLL3_PFD4] = imx_clk_pfd("pll3_pfd4", "pll3_main", PFD_PLL3_BASE, 3); - - clk[VF610_CLK_PLL4_MAIN] = imx_clk_fixed_factor("pll4_main", "fast_clk_sel", 25, 1); - /* Enet pll: fixed 50Mhz */ - clk[VF610_CLK_PLL5_MAIN] = imx_clk_fixed_factor("pll5_main", "fast_clk_sel", 125, 6); - /* pll6: default 960Mhz */ - clk[VF610_CLK_PLL6_MAIN] = imx_clk_fixed_factor("pll6_main", "fast_clk_sel", 40, 1); - /* pll7: USB1 PLL at 480MHz */ - clk[VF610_CLK_PLL7_MAIN] = imx_clk_pllv3(IMX_PLLV3_USB, "pll7_main", "fast_clk_sel", PLL7_CTRL, 0x2); + clk[VF610_CLK_PLL1_BYPASS_SRC] = imx_clk_mux("pll1_bypass_src", PLL1_CTRL, 14, 1, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels)); + clk[VF610_CLK_PLL2_BYPASS_SRC] = imx_clk_mux("pll2_bypass_src", PLL2_CTRL, 14, 1, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels)); + clk[VF610_CLK_PLL3_BYPASS_SRC] = imx_clk_mux("pll3_bypass_src", PLL3_CTRL, 14, 1, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels)); + clk[VF610_CLK_PLL4_BYPASS_SRC] = imx_clk_mux("pll4_bypass_src", PLL4_CTRL, 14, 1, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels)); + clk[VF610_CLK_PLL5_BYPASS_SRC] = imx_clk_mux("pll5_bypass_src", PLL5_CTRL, 14, 1, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels)); + clk[VF610_CLK_PLL6_BYPASS_SRC] = imx_clk_mux("pll6_bypass_src", PLL6_CTRL, 14, 1, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels)); + clk[VF610_CLK_PLL7_BYPASS_SRC] = imx_clk_mux("pll7_bypass_src", PLL7_CTRL, 14, 1, pll_bypass_src_sels, ARRAY_SIZE(pll_bypass_src_sels)); + + clk[VF610_CLK_PLL1] = imx_clk_pllv3(IMX_PLLV3_GENERIC, "pll1", "pll1_bypass_src", PLL1_CTRL, 0x1); + clk[VF610_CLK_PLL2] = imx_clk_pllv3(IMX_PLLV3_GENERIC, "pll2", "pll2_bypass_src", PLL2_CTRL, 0x1); + clk[VF610_CLK_PLL3] = imx_clk_pllv3(IMX_PLLV3_USB, "pll3", "pll3_bypass_src", PLL3_CTRL, 0x1); + clk[VF610_CLK_PLL4] = imx_clk_pllv3(IMX_PLLV3_AV, "pll4", "pll4_bypass_src", PLL4_CTRL, 0x7f); + clk[VF610_CLK_PLL5] = imx_clk_pllv3(IMX_PLLV3_ENET, "pll5", "pll5_bypass_src", PLL5_CTRL, 0x3); + clk[VF610_CLK_PLL6] = imx_clk_pllv3(IMX_PLLV3_AV, "pll6", "pll6_bypass_src", PLL6_CTRL, 0x7f); + clk[VF610_CLK_PLL7] = imx_clk_pllv3(IMX_PLLV3_USB, "pll7", "pll7_bypass_src", PLL7_CTRL, 0x1); + + clk[VF610_PLL1_BYPASS] = imx_clk_mux_flags("pll1_bypass", PLL1_CTRL, 16, 1, pll1_bypass_sels, ARRAY_SIZE(pll1_bypass_sels), CLK_SET_RATE_PARENT); + clk[VF610_PLL2_BYPASS] = imx_clk_mux_flags("pll2_bypass", PLL2_CTRL, 16, 1, pll2_bypass_sels, ARRAY_SIZE(pll2_bypass_sels), CLK_SET_RATE_PARENT); + clk[VF610_PLL3_BYPASS] = imx_clk_mux_flags("pll3_bypass", PLL3_CTRL, 16, 1, pll3_bypass_sels, ARRAY_SIZE(pll3_bypass_sels), CLK_SET_RATE_PARENT); + clk[VF610_PLL4_BYPASS] = imx_clk_mux_flags("pll4_bypass", PLL4_CTRL, 16, 1, pll4_bypass_sels, ARRAY_SIZE(pll4_bypass_sels), CLK_SET_RATE_PARENT); + clk[VF610_PLL5_BYPASS] = imx_clk_mux_flags("pll5_bypass", PLL5_CTRL, 16, 1, pll5_bypass_sels, ARRAY_SIZE(pll5_bypass_sels), CLK_SET_RATE_PARENT); + clk[VF610_PLL6_BYPASS] = imx_clk_mux_flags("pll6_bypass", PLL6_CTRL, 16, 1, pll6_bypass_sels, ARRAY_SIZE(pll6_bypass_sels), CLK_SET_RATE_PARENT); + clk[VF610_PLL7_BYPASS] = imx_clk_mux_flags("pll7_bypass", PLL7_CTRL, 16, 1, pll7_bypass_sels, ARRAY_SIZE(pll7_bypass_sels), CLK_SET_RATE_PARENT); + + /* Do not bypass PLLs initially */ + clk_set_parent(clk[VF610_PLL1_BYPASS], clk[VF610_CLK_PLL1]); + clk_set_parent(clk[VF610_PLL2_BYPASS], clk[VF610_CLK_PLL2]); + clk_set_parent(clk[VF610_PLL3_BYPASS], clk[VF610_CLK_PLL3]); + clk_set_parent(clk[VF610_PLL4_BYPASS], clk[VF610_CLK_PLL4]); + clk_set_parent(clk[VF610_PLL5_BYPASS], clk[VF610_CLK_PLL5]); + clk_set_parent(clk[VF610_PLL6_BYPASS], clk[VF610_CLK_PLL6]); + clk_set_parent(clk[VF610_PLL7_BYPASS], clk[VF610_CLK_PLL7]); + + clk[VF610_CLK_PLL1_SYS] = imx_clk_gate("pll1_sys", "pll1_bypass", PLL1_CTRL, 13); + clk[VF610_CLK_PLL2_BUS] = imx_clk_gate("pll2_bus", "pll2_bypass", PLL2_CTRL, 13); + clk[VF610_CLK_PLL3_USB_OTG] = imx_clk_gate("pll3_usb_otg", "pll3_bypass", PLL3_CTRL, 13); + clk[VF610_CLK_PLL4_AUDIO] = imx_clk_gate("pll4_audio", "pll4_bypass", PLL4_CTRL, 13); + clk[VF610_CLK_PLL5_ENET] = imx_clk_gate("pll5_enet", "pll5_bypass", PLL5_CTRL, 13); + clk[VF610_CLK_PLL6_VIDEO] = imx_clk_gate("pll6_video", "pll6_bypass", PLL6_CTRL, 13); + clk[VF610_CLK_PLL7_USB_HOST] = imx_clk_gate("pll7_usb_host", "pll7_bypass", PLL7_CTRL, 13); + + clk[VF610_CLK_LVDS1_IN] = imx_clk_gate_exclusive("lvds1_in", "anaclk1", ANA_MISC1, 12, BIT(10)); + + clk[VF610_CLK_PLL1_PFD1] = imx_clk_pfd("pll1_pfd1", "pll1_sys", PFD_PLL1_BASE, 0); + clk[VF610_CLK_PLL1_PFD2] = imx_clk_pfd("pll1_pfd2", "pll1_sys", PFD_PLL1_BASE, 1); + clk[VF610_CLK_PLL1_PFD3] = imx_clk_pfd("pll1_pfd3", "pll1_sys", PFD_PLL1_BASE, 2); + clk[VF610_CLK_PLL1_PFD4] = imx_clk_pfd("pll1_pfd4", "pll1_sys", PFD_PLL1_BASE, 3); + + clk[VF610_CLK_PLL2_PFD1] = imx_clk_pfd("pll2_pfd1", "pll2_bus", PFD_PLL2_BASE, 0); + clk[VF610_CLK_PLL2_PFD2] = imx_clk_pfd("pll2_pfd2", "pll2_bus", PFD_PLL2_BASE, 1); + clk[VF610_CLK_PLL2_PFD3] = imx_clk_pfd("pll2_pfd3", "pll2_bus", PFD_PLL2_BASE, 2); + clk[VF610_CLK_PLL2_PFD4] = imx_clk_pfd("pll2_pfd4", "pll2_bus", PFD_PLL2_BASE, 3); + + clk[VF610_CLK_PLL3_PFD1] = imx_clk_pfd("pll3_pfd1", "pll3_usb_otg", PFD_PLL3_BASE, 0); + clk[VF610_CLK_PLL3_PFD2] = imx_clk_pfd("pll3_pfd2", "pll3_usb_otg", PFD_PLL3_BASE, 1); + clk[VF610_CLK_PLL3_PFD3] = imx_clk_pfd("pll3_pfd3", "pll3_usb_otg", PFD_PLL3_BASE, 2); + clk[VF610_CLK_PLL3_PFD4] = imx_clk_pfd("pll3_pfd4", "pll3_usb_otg", PFD_PLL3_BASE, 3); clk[VF610_CLK_PLL1_PFD_SEL] = imx_clk_mux("pll1_pfd_sel", CCM_CCSR, 16, 3, pll1_sels, 5); clk[VF610_CLK_PLL2_PFD_SEL] = imx_clk_mux("pll2_pfd_sel", CCM_CCSR, 19, 3, pll2_sels, 5); @@ -167,12 +217,12 @@ static void __init vf610_clocks_init(struct device_node *ccm_node) clk[VF610_CLK_PLATFORM_BUS] = imx_clk_divider("platform_bus", "sys_bus", CCM_CACRR, 3, 3); clk[VF610_CLK_IPG_BUS] = imx_clk_divider("ipg_bus", "platform_bus", CCM_CACRR, 11, 2); - clk[VF610_CLK_PLL3_MAIN_DIV] = imx_clk_divider("pll3_main_div", "pll3_main", CCM_CACRR, 20, 1); - clk[VF610_CLK_PLL4_MAIN_DIV] = clk_register_divider_table(NULL, "pll4_main_div", "pll4_main", 0, CCM_CACRR, 6, 3, 0, pll4_main_div_table, &imx_ccm_lock); - clk[VF610_CLK_PLL6_MAIN_DIV] = imx_clk_divider("pll6_main_div", "pll6_main", CCM_CACRR, 21, 1); + clk[VF610_CLK_PLL3_MAIN_DIV] = imx_clk_divider("pll3_usb_otg_div", "pll3_usb_otg", CCM_CACRR, 20, 1); + clk[VF610_CLK_PLL4_MAIN_DIV] = clk_register_divider_table(NULL, "pll4_audio_div", "pll4_audio", 0, CCM_CACRR, 6, 3, 0, pll4_audio_div_table, &imx_ccm_lock); + clk[VF610_CLK_PLL6_MAIN_DIV] = imx_clk_divider("pll6_video_div", "pll6_video", CCM_CACRR, 21, 1); - clk[VF610_CLK_USBPHY0] = imx_clk_gate("usbphy0", "pll3_main", PLL3_CTRL, 6); - clk[VF610_CLK_USBPHY1] = imx_clk_gate("usbphy1", "pll7_main", PLL7_CTRL, 6); + clk[VF610_CLK_USBPHY0] = imx_clk_gate("usbphy0", "pll3_usb_otg", PLL3_CTRL, 6); + clk[VF610_CLK_USBPHY1] = imx_clk_gate("usbphy1", "pll7_usb_host", PLL7_CTRL, 6); clk[VF610_CLK_USBC0] = imx_clk_gate2("usbc0", "ipg_bus", CCM_CCGR1, CCM_CCGRx_CGn(4)); clk[VF610_CLK_USBC1] = imx_clk_gate2("usbc1", "ipg_bus", CCM_CCGR7, CCM_CCGRx_CGn(4)); @@ -191,8 +241,8 @@ static void __init vf610_clocks_init(struct device_node *ccm_node) clk[VF610_CLK_QSPI1_X1_DIV] = imx_clk_divider("qspi1_x1", "qspi1_x2", CCM_CSCDR3, 11, 1); clk[VF610_CLK_QSPI1] = imx_clk_gate2("qspi1", "qspi1_x1", CCM_CCGR8, CCM_CCGRx_CGn(4)); - clk[VF610_CLK_ENET_50M] = imx_clk_fixed_factor("enet_50m", "pll5_main", 1, 10); - clk[VF610_CLK_ENET_25M] = imx_clk_fixed_factor("enet_25m", "pll5_main", 1, 20); + clk[VF610_CLK_ENET_50M] = imx_clk_fixed_factor("enet_50m", "pll5_enet", 1, 10); + clk[VF610_CLK_ENET_25M] = imx_clk_fixed_factor("enet_25m", "pll5_enet", 1, 20); clk[VF610_CLK_ENET_SEL] = imx_clk_mux("enet_sel", CCM_CSCMR2, 4, 2, rmii_sels, 4); clk[VF610_CLK_ENET_TS_SEL] = imx_clk_mux("enet_ts_sel", CCM_CSCMR2, 0, 3, enet_ts_sels, 7); clk[VF610_CLK_ENET] = imx_clk_gate("enet", "enet_sel", CCM_CSCDR1, 24); diff --git a/include/dt-bindings/clock/vf610-clock.h b/include/dt-bindings/clock/vf610-clock.h index d6b56b21539..801c0ac50c4 100644 --- a/include/dt-bindings/clock/vf610-clock.h +++ b/include/dt-bindings/clock/vf610-clock.h @@ -21,24 +21,24 @@ #define VF610_CLK_FASK_CLK_SEL 8 #define VF610_CLK_AUDIO_EXT 9 #define VF610_CLK_ENET_EXT 10 -#define VF610_CLK_PLL1_MAIN 11 +#define VF610_CLK_PLL1_SYS 11 #define VF610_CLK_PLL1_PFD1 12 #define VF610_CLK_PLL1_PFD2 13 #define VF610_CLK_PLL1_PFD3 14 #define VF610_CLK_PLL1_PFD4 15 -#define VF610_CLK_PLL2_MAIN 16 +#define VF610_CLK_PLL2_BUS 16 #define VF610_CLK_PLL2_PFD1 17 #define VF610_CLK_PLL2_PFD2 18 #define VF610_CLK_PLL2_PFD3 19 #define VF610_CLK_PLL2_PFD4 20 -#define VF610_CLK_PLL3_MAIN 21 +#define VF610_CLK_PLL3_USB_OTG 21 #define VF610_CLK_PLL3_PFD1 22 #define VF610_CLK_PLL3_PFD2 23 #define VF610_CLK_PLL3_PFD3 24 #define VF610_CLK_PLL3_PFD4 25 -#define VF610_CLK_PLL4_MAIN 26 -#define VF610_CLK_PLL5_MAIN 27 -#define VF610_CLK_PLL6_MAIN 28 +#define VF610_CLK_PLL4_AUDIO 26 +#define VF610_CLK_PLL5_ENET 27 +#define VF610_CLK_PLL6_VIDEO 28 #define VF610_CLK_PLL3_MAIN_DIV 29 #define VF610_CLK_PLL4_MAIN_DIV 30 #define VF610_CLK_PLL6_MAIN_DIV 31 @@ -166,9 +166,32 @@ #define VF610_CLK_DMAMUX3 153 #define VF610_CLK_FLEXCAN0_EN 154 #define VF610_CLK_FLEXCAN1_EN 155 -#define VF610_CLK_PLL7_MAIN 156 +#define VF610_CLK_PLL7_USB_HOST 156 #define VF610_CLK_USBPHY0 157 #define VF610_CLK_USBPHY1 158 -#define VF610_CLK_END 159 +#define VF610_CLK_LVDS1_IN 159 +#define VF610_CLK_ANACLK1 160 +#define VF610_CLK_PLL1_BYPASS_SRC 161 +#define VF610_CLK_PLL2_BYPASS_SRC 162 +#define VF610_CLK_PLL3_BYPASS_SRC 163 +#define VF610_CLK_PLL4_BYPASS_SRC 164 +#define VF610_CLK_PLL5_BYPASS_SRC 165 +#define VF610_CLK_PLL6_BYPASS_SRC 166 +#define VF610_CLK_PLL7_BYPASS_SRC 167 +#define VF610_CLK_PLL1 168 +#define VF610_CLK_PLL2 169 +#define VF610_CLK_PLL3 170 +#define VF610_CLK_PLL4 171 +#define VF610_CLK_PLL5 172 +#define VF610_CLK_PLL6 173 +#define VF610_CLK_PLL7 174 +#define VF610_PLL1_BYPASS 175 +#define VF610_PLL2_BYPASS 176 +#define VF610_PLL3_BYPASS 177 +#define VF610_PLL4_BYPASS 178 +#define VF610_PLL5_BYPASS 179 +#define VF610_PLL6_BYPASS 180 +#define VF610_PLL7_BYPASS 181 +#define VF610_CLK_END 182 #endif /* __DT_BINDINGS_CLOCK_VF610_H */ -- cgit v1.2.3-70-g09d2 From a87fa1d81a9fb5e9adca9820e16008c40ad09f33 Mon Sep 17 00:00:00 2001 From: Grant Likely Date: Mon, 3 Nov 2014 15:15:35 +0000 Subject: of: Fix overflow bug in string property parsing functions The string property read helpers will run off the end of the buffer if it is handed a malformed string property. Rework the parsers to make sure that doesn't happen. At the same time add new test cases to make sure the functions behave themselves. The original implementations of of_property_read_string_index() and of_property_count_strings() both open-coded the same block of parsing code, each with it's own subtly different bugs. The fix here merges functions into a single helper and makes the original functions static inline wrappers around the helper. One non-bugfix aspect of this patch is the addition of a new wrapper, of_property_read_string_array(). The new wrapper is needed by the device_properties feature that Rafael is working on and planning to merge for v3.19. The implementation is identical both with and without the new static inline wrapper, so it just got left in to reduce the churn on the header file. Signed-off-by: Grant Likely Cc: Rafael J. Wysocki Cc: Mika Westerberg Cc: Rob Herring Cc: Arnd Bergmann Cc: Darren Hart Cc: # v3.3+: Drop selftest hunks that don't apply --- drivers/of/base.c | 88 ++++++++--------------------- drivers/of/selftest.c | 66 ++++++++++++++++++++-- drivers/of/testcase-data/tests-phandle.dtsi | 2 + include/linux/of.h | 84 ++++++++++++++++++++++----- 4 files changed, 154 insertions(+), 86 deletions(-) diff --git a/drivers/of/base.c b/drivers/of/base.c index 2305dc0382b..3823edf2d01 100644 --- a/drivers/of/base.c +++ b/drivers/of/base.c @@ -1279,52 +1279,6 @@ int of_property_read_string(struct device_node *np, const char *propname, } EXPORT_SYMBOL_GPL(of_property_read_string); -/** - * of_property_read_string_index - Find and read a string from a multiple - * strings property. - * @np: device node from which the property value is to be read. - * @propname: name of the property to be searched. - * @index: index of the string in the list of strings - * @out_string: pointer to null terminated return string, modified only if - * return value is 0. - * - * Search for a property in a device tree node and retrieve a null - * terminated string value (pointer to data, not a copy) in the list of strings - * contained in that property. - * Returns 0 on success, -EINVAL if the property does not exist, -ENODATA if - * property does not have a value, and -EILSEQ if the string is not - * null-terminated within the length of the property data. - * - * The out_string pointer is modified only if a valid string can be decoded. - */ -int of_property_read_string_index(struct device_node *np, const char *propname, - int index, const char **output) -{ - struct property *prop = of_find_property(np, propname, NULL); - int i = 0; - size_t l = 0, total = 0; - const char *p; - - if (!prop) - return -EINVAL; - if (!prop->value) - return -ENODATA; - if (strnlen(prop->value, prop->length) >= prop->length) - return -EILSEQ; - - p = prop->value; - - for (i = 0; total < prop->length; total += l, p += l) { - l = strlen(p) + 1; - if (i++ == index) { - *output = p; - return 0; - } - } - return -ENODATA; -} -EXPORT_SYMBOL_GPL(of_property_read_string_index); - /** * of_property_match_string() - Find string in a list and return index * @np: pointer to node containing string list property @@ -1351,7 +1305,7 @@ int of_property_match_string(struct device_node *np, const char *propname, end = p + prop->length; for (i = 0; p < end; i++, p += l) { - l = strlen(p) + 1; + l = strnlen(p, end - p) + 1; if (p + l > end) return -EILSEQ; pr_debug("comparing %s with %s\n", string, p); @@ -1363,39 +1317,41 @@ int of_property_match_string(struct device_node *np, const char *propname, EXPORT_SYMBOL_GPL(of_property_match_string); /** - * of_property_count_strings - Find and return the number of strings from a - * multiple strings property. + * of_property_read_string_util() - Utility helper for parsing string properties * @np: device node from which the property value is to be read. * @propname: name of the property to be searched. + * @out_strs: output array of string pointers. + * @sz: number of array elements to read. + * @skip: Number of strings to skip over at beginning of list. * - * Search for a property in a device tree node and retrieve the number of null - * terminated string contain in it. Returns the number of strings on - * success, -EINVAL if the property does not exist, -ENODATA if property - * does not have a value, and -EILSEQ if the string is not null-terminated - * within the length of the property data. + * Don't call this function directly. It is a utility helper for the + * of_property_read_string*() family of functions. */ -int of_property_count_strings(struct device_node *np, const char *propname) +int of_property_read_string_helper(struct device_node *np, const char *propname, + const char **out_strs, size_t sz, int skip) { struct property *prop = of_find_property(np, propname, NULL); - int i = 0; - size_t l = 0, total = 0; - const char *p; + int l = 0, i = 0; + const char *p, *end; if (!prop) return -EINVAL; if (!prop->value) return -ENODATA; - if (strnlen(prop->value, prop->length) >= prop->length) - return -EILSEQ; - p = prop->value; + end = p + prop->length; - for (i = 0; total < prop->length; total += l, p += l, i++) - l = strlen(p) + 1; - - return i; + for (i = 0; p < end && (!out_strs || i < skip + sz); i++, p += l) { + l = strnlen(p, end - p) + 1; + if (p + l > end) + return -EILSEQ; + if (out_strs && i >= skip) + *out_strs++ = p; + } + i -= skip; + return i <= 0 ? -ENODATA : i; } -EXPORT_SYMBOL_GPL(of_property_count_strings); +EXPORT_SYMBOL_GPL(of_property_read_string_helper); void of_print_phandle_args(const char *msg, const struct of_phandle_args *args) { diff --git a/drivers/of/selftest.c b/drivers/of/selftest.c index 78001270a59..11b873c54a7 100644 --- a/drivers/of/selftest.c +++ b/drivers/of/selftest.c @@ -339,8 +339,9 @@ static void __init of_selftest_parse_phandle_with_args(void) selftest(rc == -EINVAL, "expected:%i got:%i\n", -EINVAL, rc); } -static void __init of_selftest_property_match_string(void) +static void __init of_selftest_property_string(void) { + const char *strings[4]; struct device_node *np; int rc; @@ -357,13 +358,66 @@ static void __init of_selftest_property_match_string(void) rc = of_property_match_string(np, "phandle-list-names", "third"); selftest(rc == 2, "third expected:0 got:%i\n", rc); rc = of_property_match_string(np, "phandle-list-names", "fourth"); - selftest(rc == -ENODATA, "unmatched string; rc=%i", rc); + selftest(rc == -ENODATA, "unmatched string; rc=%i\n", rc); rc = of_property_match_string(np, "missing-property", "blah"); - selftest(rc == -EINVAL, "missing property; rc=%i", rc); + selftest(rc == -EINVAL, "missing property; rc=%i\n", rc); rc = of_property_match_string(np, "empty-property", "blah"); - selftest(rc == -ENODATA, "empty property; rc=%i", rc); + selftest(rc == -ENODATA, "empty property; rc=%i\n", rc); rc = of_property_match_string(np, "unterminated-string", "blah"); - selftest(rc == -EILSEQ, "unterminated string; rc=%i", rc); + selftest(rc == -EILSEQ, "unterminated string; rc=%i\n", rc); + + /* of_property_count_strings() tests */ + rc = of_property_count_strings(np, "string-property"); + selftest(rc == 1, "Incorrect string count; rc=%i\n", rc); + rc = of_property_count_strings(np, "phandle-list-names"); + selftest(rc == 3, "Incorrect string count; rc=%i\n", rc); + rc = of_property_count_strings(np, "unterminated-string"); + selftest(rc == -EILSEQ, "unterminated string; rc=%i\n", rc); + rc = of_property_count_strings(np, "unterminated-string-list"); + selftest(rc == -EILSEQ, "unterminated string array; rc=%i\n", rc); + + /* of_property_read_string_index() tests */ + rc = of_property_read_string_index(np, "string-property", 0, strings); + selftest(rc == 0 && !strcmp(strings[0], "foobar"), "of_property_read_string_index() failure; rc=%i\n", rc); + strings[0] = NULL; + rc = of_property_read_string_index(np, "string-property", 1, strings); + selftest(rc == -ENODATA && strings[0] == NULL, "of_property_read_string_index() failure; rc=%i\n", rc); + rc = of_property_read_string_index(np, "phandle-list-names", 0, strings); + selftest(rc == 0 && !strcmp(strings[0], "first"), "of_property_read_string_index() failure; rc=%i\n", rc); + rc = of_property_read_string_index(np, "phandle-list-names", 1, strings); + selftest(rc == 0 && !strcmp(strings[0], "second"), "of_property_read_string_index() failure; rc=%i\n", rc); + rc = of_property_read_string_index(np, "phandle-list-names", 2, strings); + selftest(rc == 0 && !strcmp(strings[0], "third"), "of_property_read_string_index() failure; rc=%i\n", rc); + strings[0] = NULL; + rc = of_property_read_string_index(np, "phandle-list-names", 3, strings); + selftest(rc == -ENODATA && strings[0] == NULL, "of_property_read_string_index() failure; rc=%i\n", rc); + strings[0] = NULL; + rc = of_property_read_string_index(np, "unterminated-string", 0, strings); + selftest(rc == -EILSEQ && strings[0] == NULL, "of_property_read_string_index() failure; rc=%i\n", rc); + rc = of_property_read_string_index(np, "unterminated-string-list", 0, strings); + selftest(rc == 0 && !strcmp(strings[0], "first"), "of_property_read_string_index() failure; rc=%i\n", rc); + strings[0] = NULL; + rc = of_property_read_string_index(np, "unterminated-string-list", 2, strings); /* should fail */ + selftest(rc == -EILSEQ && strings[0] == NULL, "of_property_read_string_index() failure; rc=%i\n", rc); + strings[1] = NULL; + + /* of_property_read_string_array() tests */ + rc = of_property_read_string_array(np, "string-property", strings, 4); + selftest(rc == 1, "Incorrect string count; rc=%i\n", rc); + rc = of_property_read_string_array(np, "phandle-list-names", strings, 4); + selftest(rc == 3, "Incorrect string count; rc=%i\n", rc); + rc = of_property_read_string_array(np, "unterminated-string", strings, 4); + selftest(rc == -EILSEQ, "unterminated string; rc=%i\n", rc); + /* -- An incorrectly formed string should cause a failure */ + rc = of_property_read_string_array(np, "unterminated-string-list", strings, 4); + selftest(rc == -EILSEQ, "unterminated string array; rc=%i\n", rc); + /* -- parsing the correctly formed strings should still work: */ + strings[2] = NULL; + rc = of_property_read_string_array(np, "unterminated-string-list", strings, 2); + selftest(rc == 2 && strings[2] == NULL, "of_property_read_string_array() failure; rc=%i\n", rc); + strings[1] = NULL; + rc = of_property_read_string_array(np, "phandle-list-names", strings, 1); + selftest(rc == 1 && strings[1] == NULL, "Overwrote end of string array; rc=%i, str='%s'\n", rc, strings[1]); } #define propcmp(p1, p2) (((p1)->length == (p2)->length) && \ @@ -881,7 +935,7 @@ static int __init of_selftest(void) of_selftest_find_node_by_name(); of_selftest_dynamic(); of_selftest_parse_phandle_with_args(); - of_selftest_property_match_string(); + of_selftest_property_string(); of_selftest_property_copy(); of_selftest_changeset(); of_selftest_parse_interrupts(); diff --git a/drivers/of/testcase-data/tests-phandle.dtsi b/drivers/of/testcase-data/tests-phandle.dtsi index ce0fe083d40..5b1527e8a7f 100644 --- a/drivers/of/testcase-data/tests-phandle.dtsi +++ b/drivers/of/testcase-data/tests-phandle.dtsi @@ -39,7 +39,9 @@ phandle-list-bad-args = <&provider2 1 0>, <&provider3 0>; empty-property; + string-property = "foobar"; unterminated-string = [40 41 42 43]; + unterminated-string-list = "first", "second", [40 41 42 43]; }; }; }; diff --git a/include/linux/of.h b/include/linux/of.h index 6545e7aec7b..29f0adc5f3e 100644 --- a/include/linux/of.h +++ b/include/linux/of.h @@ -267,14 +267,12 @@ extern int of_property_read_u64(const struct device_node *np, extern int of_property_read_string(struct device_node *np, const char *propname, const char **out_string); -extern int of_property_read_string_index(struct device_node *np, - const char *propname, - int index, const char **output); extern int of_property_match_string(struct device_node *np, const char *propname, const char *string); -extern int of_property_count_strings(struct device_node *np, - const char *propname); +extern int of_property_read_string_helper(struct device_node *np, + const char *propname, + const char **out_strs, size_t sz, int index); extern int of_device_is_compatible(const struct device_node *device, const char *); extern int of_device_is_available(const struct device_node *device); @@ -486,15 +484,9 @@ static inline int of_property_read_string(struct device_node *np, return -ENOSYS; } -static inline int of_property_read_string_index(struct device_node *np, - const char *propname, int index, - const char **out_string) -{ - return -ENOSYS; -} - -static inline int of_property_count_strings(struct device_node *np, - const char *propname) +static inline int of_property_read_string_helper(struct device_node *np, + const char *propname, + const char **out_strs, size_t sz, int index) { return -ENOSYS; } @@ -667,6 +659,70 @@ static inline int of_property_count_u64_elems(const struct device_node *np, return of_property_count_elems_of_size(np, propname, sizeof(u64)); } +/** + * of_property_read_string_array() - Read an array of strings from a multiple + * strings property. + * @np: device node from which the property value is to be read. + * @propname: name of the property to be searched. + * @out_strs: output array of string pointers. + * @sz: number of array elements to read. + * + * Search for a property in a device tree node and retrieve a list of + * terminated string values (pointer to data, not a copy) in that property. + * + * If @out_strs is NULL, the number of strings in the property is returned. + */ +static inline int of_property_read_string_array(struct device_node *np, + const char *propname, const char **out_strs, + size_t sz) +{ + return of_property_read_string_helper(np, propname, out_strs, sz, 0); +} + +/** + * of_property_count_strings() - Find and return the number of strings from a + * multiple strings property. + * @np: device node from which the property value is to be read. + * @propname: name of the property to be searched. + * + * Search for a property in a device tree node and retrieve the number of null + * terminated string contain in it. Returns the number of strings on + * success, -EINVAL if the property does not exist, -ENODATA if property + * does not have a value, and -EILSEQ if the string is not null-terminated + * within the length of the property data. + */ +static inline int of_property_count_strings(struct device_node *np, + const char *propname) +{ + return of_property_read_string_helper(np, propname, NULL, 0, 0); +} + +/** + * of_property_read_string_index() - Find and read a string from a multiple + * strings property. + * @np: device node from which the property value is to be read. + * @propname: name of the property to be searched. + * @index: index of the string in the list of strings + * @out_string: pointer to null terminated return string, modified only if + * return value is 0. + * + * Search for a property in a device tree node and retrieve a null + * terminated string value (pointer to data, not a copy) in the list of strings + * contained in that property. + * Returns 0 on success, -EINVAL if the property does not exist, -ENODATA if + * property does not have a value, and -EILSEQ if the string is not + * null-terminated within the length of the property data. + * + * The out_string pointer is modified only if a valid string can be decoded. + */ +static inline int of_property_read_string_index(struct device_node *np, + const char *propname, + int index, const char **output) +{ + int rc = of_property_read_string_helper(np, propname, output, 1, index); + return rc < 0 ? rc : 0; +} + /** * of_property_read_bool - Findfrom a property * @np: device node from which the property value is to be read. -- cgit v1.2.3-70-g09d2 From 5cc7b04740effa5cc0af53f434134b5859d58b73 Mon Sep 17 00:00:00 2001 From: Alexander Stein Date: Tue, 4 Nov 2014 09:20:18 +0100 Subject: spi: fsl-dspi: Fix CTAR selection There are only 4 CTAR registers (CTAR0 - CTAR3) so we can only use the lower 2 bits of the chip select to select a CTAR register. SPI_PUSHR_CTAS used the lower 3 bits which would result in wrong bit values if the chip selects 4/5 are used. For those chip selects SPI_CTAR even calculated offsets of non-existing registers. Signed-off-by: Alexander Stein Signed-off-by: Mark Brown Cc: stable@vger.kernel.org --- drivers/spi/spi-fsl-dspi.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/spi/spi-fsl-dspi.c b/drivers/spi/spi-fsl-dspi.c index 448216025ce..831ceb4a91f 100644 --- a/drivers/spi/spi-fsl-dspi.c +++ b/drivers/spi/spi-fsl-dspi.c @@ -46,7 +46,7 @@ #define SPI_TCR 0x08 -#define SPI_CTAR(x) (0x0c + (x * 4)) +#define SPI_CTAR(x) (0x0c + (((x) & 0x3) * 4)) #define SPI_CTAR_FMSZ(x) (((x) & 0x0000000f) << 27) #define SPI_CTAR_CPOL(x) ((x) << 26) #define SPI_CTAR_CPHA(x) ((x) << 25) @@ -70,7 +70,7 @@ #define SPI_PUSHR 0x34 #define SPI_PUSHR_CONT (1 << 31) -#define SPI_PUSHR_CTAS(x) (((x) & 0x00000007) << 28) +#define SPI_PUSHR_CTAS(x) (((x) & 0x00000003) << 28) #define SPI_PUSHR_EOQ (1 << 27) #define SPI_PUSHR_CTCNT (1 << 26) #define SPI_PUSHR_PCS(x) (((1 << x) & 0x0000003f) << 16) -- cgit v1.2.3-70-g09d2 From 89fbec5b97fbcf08db3a9cd93a340f21f95d38b8 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Tue, 4 Nov 2014 08:28:47 -0200 Subject: ARM: imx: Fix the removal of CONFIG_SPI option Since 64546e9fe3a5b8c ("ARM: imx_v6_v7_defconfig updates") and commit 0650f855d2e4b0b9 ("ARM: imx_v4_v5_defconfig: Select CONFIG_IMX_WEIM") CONFIG_SPI selection was dropped by savedefconfig for imx_v4_v5_defconfig and imx_v6_v7_defconfig. In order to keep the same behaviour as previous kernel versions and avoid regressions, let's add CONFIG_SPI option back. Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/configs/imx_v4_v5_defconfig | 1 + arch/arm/configs/imx_v6_v7_defconfig | 1 + 2 files changed, 2 insertions(+) diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig index e688741c89a..e6b0007355f 100644 --- a/arch/arm/configs/imx_v4_v5_defconfig +++ b/arch/arm/configs/imx_v4_v5_defconfig @@ -97,6 +97,7 @@ CONFIG_SERIAL_IMX_CONSOLE=y # CONFIG_HW_RANDOM is not set CONFIG_I2C_CHARDEV=y CONFIG_I2C_IMX=y +CONFIG_SPI=y CONFIG_SPI_IMX=y CONFIG_SPI_SPIDEV=y CONFIG_GPIO_SYSFS=y diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig index 8fca6e276b6..6790f1b3f3a 100644 --- a/arch/arm/configs/imx_v6_v7_defconfig +++ b/arch/arm/configs/imx_v6_v7_defconfig @@ -158,6 +158,7 @@ CONFIG_I2C_CHARDEV=y CONFIG_I2C_ALGOPCF=m CONFIG_I2C_ALGOPCA=m CONFIG_I2C_IMX=y +CONFIG_SPI=y CONFIG_SPI_IMX=y CONFIG_GPIO_SYSFS=y CONFIG_GPIO_MC9S08DZ60=y -- cgit v1.2.3-70-g09d2 From 0097761013253930341e23723d64e0845c3f9edd Mon Sep 17 00:00:00 2001 From: Ralf Baechle Date: Tue, 4 Nov 2014 11:54:29 +0100 Subject: MIPS: Fix strnlen_user() return value in case of overlong strings. We were returning maxlen like the userland strnlen if no '\0' character was encountered while the kernel version is expected to return a value larger than maxlen. Fixed to return maxlen + 1. Signed-off-by: Ralf Baechle --- arch/mips/lib/strnlen_user.S | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/arch/mips/lib/strnlen_user.S b/arch/mips/lib/strnlen_user.S index f3af6995e2a..7d12c0dded3 100644 --- a/arch/mips/lib/strnlen_user.S +++ b/arch/mips/lib/strnlen_user.S @@ -40,9 +40,11 @@ FEXPORT(__strnlen_\func\()_nocheck_asm) .else EX(lbe, t0, (v0), .Lfault\@) .endif - PTR_ADDIU v0, 1 + .set noreorder bnez t0, 1b -1: PTR_SUBU v0, a0 +1: PTR_ADDIU v0, 1 + .set reorder + PTR_SUBU v0, a0 jr ra END(__strnlen_\func\()_asm) -- cgit v1.2.3-70-g09d2 From 6e5aafb27419f32575b27ef9d6a31e5d54661aca Mon Sep 17 00:00:00 2001 From: Chris Mason Date: Tue, 4 Nov 2014 06:59:04 -0800 Subject: Btrfs: fix kfree on list_head in btrfs_lookup_csums_range error cleanup If we hit any errors in btrfs_lookup_csums_range, we'll loop through all the csums we allocate and free them. But the code was using list_entry incorrectly, and ended up trying to free the on-stack list_head instead. This bug came from commit 0678b6185 btrfs: Don't BUG_ON kzalloc error in btrfs_lookup_csums_range() Signed-off-by: Chris Mason Reported-by: Erik Berg cc: stable@vger.kernel.org # 3.3 or newer --- fs/btrfs/file-item.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/btrfs/file-item.c b/fs/btrfs/file-item.c index 783a94355ef..84a2d186827 100644 --- a/fs/btrfs/file-item.c +++ b/fs/btrfs/file-item.c @@ -413,7 +413,7 @@ int btrfs_lookup_csums_range(struct btrfs_root *root, u64 start, u64 end, ret = 0; fail: while (ret < 0 && !list_empty(&tmplist)) { - sums = list_entry(&tmplist, struct btrfs_ordered_sum, list); + sums = list_entry(tmplist.next, struct btrfs_ordered_sum, list); list_del(&sums->list); kfree(sums); } -- cgit v1.2.3-70-g09d2 From 8bcdd9297d213c6f8c40b87423581cea0fbf37c2 Mon Sep 17 00:00:00 2001 From: Stephen Warren Date: Tue, 4 Nov 2014 20:27:17 -0700 Subject: MAINTAINERS: update bcm2835 entry Add Lee Jones as a new co-maintainer. The kernel.org repo moved to allow us both to push to it. Update MAINTAINERS to match. Signed-off-by: Stephen Warren Signed-off-by: Olof Johansson --- MAINTAINERS | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/MAINTAINERS b/MAINTAINERS index f155c2a1255..7b690fc1e44 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2072,8 +2072,9 @@ F: drivers/clocksource/bcm_kona_timer.c BROADCOM BCM2835 ARM ARCHITECTURE M: Stephen Warren +M: Lee Jones L: linux-rpi-kernel@lists.infradead.org (moderated for non-subscribers) -T: git git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi.git +T: git git://git.kernel.org/pub/scm/linux/kernel/git/rpi/linux-rpi.git S: Maintained N: bcm2835 -- cgit v1.2.3-70-g09d2 From c922c4e87b9b5a3b50d4d17b96f189121430f511 Mon Sep 17 00:00:00 2001 From: Hui Wang Date: Wed, 5 Nov 2014 12:17:58 +0800 Subject: ALSA: hda - fix mute led problem for three HP laptops Without the fix, the mute led can't work on these three machines. After apply this fix, these three machines will fall back on the led control quirk as below, and through testing, the mute led works very well. PIN_QUIRK(0x10ec0282, 0x103c, "HP", ALC269_FIXUP_HP_LINE1_MIC1_LED, ALC282_STANDARD_PINS, {0x12, 0x90a60140}, ... BugLink: https://bugs.launchpad.net/bugs/1389497 Tested-by: TieFu Chen Cc: Kailang Yang Cc: stable@vger.kernel.org Signed-off-by: Hui Wang Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index ba72fffa746..1af917f58a7 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -4744,9 +4744,6 @@ static const struct snd_pci_quirk alc269_fixup_tbl[] = { SND_PCI_QUIRK(0x103c, 0x2221, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2225, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2246, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), - SND_PCI_QUIRK(0x103c, 0x2247, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), - SND_PCI_QUIRK(0x103c, 0x2248, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), - SND_PCI_QUIRK(0x103c, 0x2249, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2253, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2254, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), SND_PCI_QUIRK(0x103c, 0x2255, "HP", ALC269_FIXUP_HP_GPIO_MIC1_LED), -- cgit v1.2.3-70-g09d2 From a31b0c6c19bf28c54999c3cd8cc3a7c8ba565a45 Mon Sep 17 00:00:00 2001 From: Kristina Martsenko Date: Wed, 5 Nov 2014 02:22:41 +0200 Subject: mmc: core: fix card detection regression MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Since commit 89168b489915 ("mmc: core: restore detect line inversion semantics"), the SD card on i.MX28 (and possibly other) devices isn't detected and booting stops at: [ 4.120617] Waiting for root device /dev/mmcblk0p3... This is caused by the MMC_CAP2_CD_ACTIVE_HIGH flag being set incorrectly when the host controller doesn't use a GPIO for card detection (but instead uses a dedicated pin). In this case mmc_gpiod_request_cd() will return before assigning to the gpio_invert variable, leaving the variable uninitialized. The variable then gets used to set the flag. This patch fixes the issue by making sure gpio_invert is set to false when a GPIO isn't used. After this patch, i.MX28 boots fine. The MMC_CAP2_RO_ACTIVE_HIGH (write protect) flag is also set incorrectly for the exact same reason (it uses the same uninitialized variable), so this patch fixes that too. Fixes: 89168b489915 ("mmc: core: restore detect line inversion semantics") Reported-by: Stefan Wahren Signed-off-by: Kristina Martšenko Tested-by: Fabio Estevam Signed-off-by: Ulf Hansson --- drivers/mmc/core/host.c | 21 ++++++++------------- 1 file changed, 8 insertions(+), 13 deletions(-) diff --git a/drivers/mmc/core/host.c b/drivers/mmc/core/host.c index 03c53b72a2d..270d58a4c43 100644 --- a/drivers/mmc/core/host.c +++ b/drivers/mmc/core/host.c @@ -311,7 +311,8 @@ int mmc_of_parse(struct mmc_host *host) struct device_node *np; u32 bus_width; int len, ret; - bool cap_invert, gpio_invert; + bool cd_cap_invert, cd_gpio_invert = false; + bool ro_cap_invert, ro_gpio_invert = false; if (!host->parent || !host->parent->of_node) return 0; @@ -359,16 +360,13 @@ int mmc_of_parse(struct mmc_host *host) if (of_find_property(np, "non-removable", &len)) { host->caps |= MMC_CAP_NONREMOVABLE; } else { - if (of_property_read_bool(np, "cd-inverted")) - cap_invert = true; - else - cap_invert = false; + cd_cap_invert = of_property_read_bool(np, "cd-inverted"); if (of_find_property(np, "broken-cd", &len)) host->caps |= MMC_CAP_NEEDS_POLL; ret = mmc_gpiod_request_cd(host, "cd", 0, true, - 0, &gpio_invert); + 0, &cd_gpio_invert); if (ret) { if (ret == -EPROBE_DEFER) return ret; @@ -391,17 +389,14 @@ int mmc_of_parse(struct mmc_host *host) * both inverted, the end result is that the CD line is * not inverted. */ - if (cap_invert ^ gpio_invert) + if (cd_cap_invert ^ cd_gpio_invert) host->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH; } /* Parse Write Protection */ - if (of_property_read_bool(np, "wp-inverted")) - cap_invert = true; - else - cap_invert = false; + ro_cap_invert = of_property_read_bool(np, "wp-inverted"); - ret = mmc_gpiod_request_ro(host, "wp", 0, false, 0, &gpio_invert); + ret = mmc_gpiod_request_ro(host, "wp", 0, false, 0, &ro_gpio_invert); if (ret) { if (ret == -EPROBE_DEFER) goto out; @@ -414,7 +409,7 @@ int mmc_of_parse(struct mmc_host *host) dev_info(host->parent, "Got WP GPIO\n"); /* See the comment on CD inversion above */ - if (cap_invert ^ gpio_invert) + if (ro_cap_invert ^ ro_gpio_invert) host->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH; if (of_find_property(np, "cap-sd-highspeed", &len)) -- cgit v1.2.3-70-g09d2 From 3f822c6264954660babce757fb45792fd3af273e Mon Sep 17 00:00:00 2001 From: Miklos Szeredi Date: Tue, 4 Nov 2014 16:11:03 +0100 Subject: ovl: don't poison cursor ovl_cache_put() can be called from ovl_dir_reset() if the cache needs to be rebuilt. We did list_del() on the cursor, which results in an Oops on the poisoned pointer in ovl_seek_cursor(). Reported-by: Jordi Pujol Palomer Signed-off-by: Miklos Szeredi Tested-by: Jordi Pujol Palomer Signed-off-by: Al Viro --- fs/overlayfs/readdir.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/overlayfs/readdir.c b/fs/overlayfs/readdir.c index 4e9d7c1fea5..2a7ef4f8e2a 100644 --- a/fs/overlayfs/readdir.c +++ b/fs/overlayfs/readdir.c @@ -168,7 +168,7 @@ static void ovl_cache_put(struct ovl_dir_file *od, struct dentry *dentry) { struct ovl_dir_cache *cache = od->cache; - list_del(&od->cursor.l_node); + list_del_init(&od->cursor.l_node); WARN_ON(cache->refcount <= 0); cache->refcount--; if (!cache->refcount) { -- cgit v1.2.3-70-g09d2 From 0725dda207e95ff25f1aa01432250323e0ec49d6 Mon Sep 17 00:00:00 2001 From: Takashi Iwai Date: Wed, 5 Nov 2014 15:08:49 +0100 Subject: ALSA: usb-audio: Fix device_del() sysfs warnings at disconnect Some USB-audio devices show weird sysfs warnings at disconnecting the devices, e.g. usb 1-3: USB disconnect, device number 3 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 973 at fs/sysfs/group.c:216 device_del+0x39/0x180() sysfs group ffffffff8183df40 not found for kobject 'midiC1D0' Call Trace: [] ? dump_stack+0x49/0x71 [] ? warn_slowpath_common+0x82/0xb0 [] ? warn_slowpath_fmt+0x45/0x50 [] ? device_del+0x39/0x180 [] ? device_unregister+0x9/0x20 [] ? device_destroy+0x34/0x40 [] ? snd_unregister_device+0x7f/0xd0 [snd] [] ? snd_rawmidi_dev_disconnect+0xce/0x100 [snd_rawmidi] [] ? snd_device_disconnect+0x62/0x90 [snd] [] ? snd_device_disconnect_all+0x3c/0x60 [snd] [] ? snd_card_disconnect+0x124/0x1a0 [snd] [] ? usb_audio_disconnect+0x88/0x1c0 [snd_usb_audio] [] ? usb_unbind_interface+0x5e/0x1b0 [usbcore] [] ? __device_release_driver+0x79/0xf0 [] ? device_release_driver+0x25/0x40 [] ? bus_remove_device+0xf1/0x130 [] ? device_del+0x109/0x180 [] ? usb_disable_device+0x95/0x1f0 [usbcore] [] ? usb_disconnect+0x8f/0x190 [usbcore] [] ? hub_thread+0x539/0x13a0 [usbcore] [] ? sched_clock_local+0x15/0x80 [] ? sched_clock_cpu+0xb8/0xd0 [] ? bit_waitqueue+0xb0/0xb0 [] ? usb_port_resume+0x430/0x430 [usbcore] [] ? usb_port_resume+0x430/0x430 [usbcore] [] ? kthread+0xce/0xf0 [] ? kthread_create_on_node+0x1c0/0x1c0 [] ? ret_from_fork+0x7c/0xb0 [] ? kthread_create_on_node+0x1c0/0x1c0 ---[ end trace 40b1928d1136b91e ]--- This comes from the fact that usb-audio driver may receive the disconnect callback multiple times, per each usb interface. When a device has both audio and midi interfaces, it gets called twice, and currently the driver tries to release resources at the last call. At this point, the first parent interface has been already deleted, thus deleting a child of the first parent hits such a warning. For fixing this problem, we need to call snd_card_disconnect() and cancel pending operations at the very first disconnect while the release of the whole objects waits until the last disconnect call. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80931 Reported-and-tested-by: Tomas Gayoso Reported-and-tested-by: Chris J Arges Cc: Signed-off-by: Takashi Iwai --- sound/usb/card.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/sound/usb/card.c b/sound/usb/card.c index 7ecd0e8a5c5..f61ebb17cc6 100644 --- a/sound/usb/card.c +++ b/sound/usb/card.c @@ -591,18 +591,19 @@ static void snd_usb_audio_disconnect(struct usb_device *dev, { struct snd_card *card; struct list_head *p; + bool was_shutdown; if (chip == (void *)-1L) return; card = chip->card; down_write(&chip->shutdown_rwsem); + was_shutdown = chip->shutdown; chip->shutdown = 1; up_write(&chip->shutdown_rwsem); mutex_lock(®ister_mutex); - chip->num_interfaces--; - if (chip->num_interfaces <= 0) { + if (!was_shutdown) { struct snd_usb_endpoint *ep; snd_card_disconnect(card); @@ -622,6 +623,10 @@ static void snd_usb_audio_disconnect(struct usb_device *dev, list_for_each(p, &chip->mixer_list) { snd_usb_mixer_disconnect(p); } + } + + chip->num_interfaces--; + if (chip->num_interfaces <= 0) { usb_chip[chip->index] = NULL; mutex_unlock(®ister_mutex); snd_card_free_when_closed(card); -- cgit v1.2.3-70-g09d2 From 97b56be10352a70c82dc51f187f6a77ffde50e40 Mon Sep 17 00:00:00 2001 From: Catalin Marinas Date: Wed, 5 Nov 2014 16:26:35 +0000 Subject: arm64: compat: Enable bpf syscall Following the arm32 commit 2d605a302972 (ARM: enable bpf syscall), wire this syscall for arm64 compat as well. Signed-off-by: Catalin Marinas --- arch/arm64/include/asm/unistd32.h | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/include/asm/unistd32.h b/arch/arm64/include/asm/unistd32.h index da1f06b535e..9dfdac4a74a 100644 --- a/arch/arm64/include/asm/unistd32.h +++ b/arch/arm64/include/asm/unistd32.h @@ -792,3 +792,5 @@ __SYSCALL(__NR_renameat2, sys_renameat2) __SYSCALL(__NR_getrandom, sys_getrandom) #define __NR_memfd_create 385 __SYSCALL(__NR_memfd_create, sys_memfd_create) +#define __NR_bpf 386 +__SYSCALL(__NR_bpf, sys_bpf) -- cgit v1.2.3-70-g09d2 From 2d39ad649eca1e8a993f4fda244fe17ecea7a38d Mon Sep 17 00:00:00 2001 From: Will Deacon Date: Wed, 5 Nov 2014 16:47:31 +0000 Subject: arm64: defconfig: update defconfig for 3.18 This patch enables a few things missing from our defconfig: - PCI and MSI, including support for the x-gene host controller - BPF JIT - SPI, GPIO and MMC for Seattle - GPIO for x-gene - USB for Juno - RTC It also removes HMC_DRV, which was being built as a module for some reason. Signed-off-by: Will Deacon Signed-off-by: Catalin Marinas --- arch/arm64/configs/defconfig | 26 ++++++++++++++++++++++++-- 1 file changed, 24 insertions(+), 2 deletions(-) diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig index 4ce602c2c6d..dd301be89ec 100644 --- a/arch/arm64/configs/defconfig +++ b/arch/arm64/configs/defconfig @@ -35,6 +35,9 @@ CONFIG_MODULE_UNLOAD=y CONFIG_ARCH_THUNDER=y CONFIG_ARCH_VEXPRESS=y CONFIG_ARCH_XGENE=y +CONFIG_PCI=y +CONFIG_PCI_MSI=y +CONFIG_PCI_XGENE=y CONFIG_SMP=y CONFIG_PREEMPT=y CONFIG_KSM=y @@ -52,6 +55,7 @@ CONFIG_IP_PNP_DHCP=y CONFIG_IP_PNP_BOOTP=y # CONFIG_INET_LRO is not set # CONFIG_IPV6 is not set +CONFIG_BPF_JIT=y # CONFIG_WIRELESS is not set CONFIG_NET_9P=y CONFIG_NET_9P_VIRTIO=y @@ -65,16 +69,17 @@ CONFIG_VIRTIO_BLK=y CONFIG_BLK_DEV_SD=y # CONFIG_SCSI_LOWLEVEL is not set CONFIG_ATA=y +CONFIG_SATA_AHCI=y +CONFIG_SATA_AHCI_PLATFORM=y CONFIG_AHCI_XGENE=y -CONFIG_PHY_XGENE=y CONFIG_PATA_PLATFORM=y CONFIG_PATA_OF_PLATFORM=y CONFIG_NETDEVICES=y CONFIG_TUN=y CONFIG_VIRTIO_NET=y +CONFIG_NET_XGENE=y CONFIG_SMC91X=y CONFIG_SMSC911X=y -CONFIG_NET_XGENE=y # CONFIG_WLAN is not set CONFIG_INPUT_EVDEV=y # CONFIG_SERIO_SERPORT is not set @@ -87,6 +92,11 @@ CONFIG_SERIAL_AMBA_PL011_CONSOLE=y CONFIG_SERIAL_OF_PLATFORM=y CONFIG_VIRTIO_CONSOLE=y # CONFIG_HW_RANDOM is not set +# CONFIG_HMC_DRV is not set +CONFIG_SPI=y +CONFIG_SPI_PL022=y +CONFIG_GPIO_PL061=y +CONFIG_GPIO_XGENE=y # CONFIG_HWMON is not set CONFIG_REGULATOR=y CONFIG_REGULATOR_FIXED_VOLTAGE=y @@ -97,13 +107,25 @@ CONFIG_LOGO=y # CONFIG_LOGO_LINUX_MONO is not set # CONFIG_LOGO_LINUX_VGA16 is not set CONFIG_USB=y +CONFIG_USB_EHCI_HCD=y +CONFIG_USB_EHCI_HCD_PLATFORM=y CONFIG_USB_ISP1760_HCD=y +CONFIG_USB_OHCI_HCD=y +CONFIG_USB_OHCI_HCD_PLATFORM=y CONFIG_USB_STORAGE=y +CONFIG_USB_ULPI=y CONFIG_MMC=y CONFIG_MMC_ARMMMCI=y +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_PLTFM=y +CONFIG_MMC_SPI=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_EFI=y +CONFIG_RTC_DRV_XGENE=y CONFIG_VIRTIO_BALLOON=y CONFIG_VIRTIO_MMIO=y # CONFIG_IOMMU_SUPPORT is not set +CONFIG_PHY_XGENE=y CONFIG_EXT2_FS=y CONFIG_EXT3_FS=y # CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set -- cgit v1.2.3-70-g09d2 From 4a53d3afa00b0b74b0e49b147902a41e55b2e715 Mon Sep 17 00:00:00 2001 From: Lars-Peter Clausen Date: Thu, 25 Sep 2014 15:27:00 +0100 Subject: staging:iio:ad5933: Fix NULL pointer deref when enabling buffer In older versions of the IIO framework it was possible to pass a completely different set of channels to iio_buffer_register() as the one that is assigned to the IIO device. Commit 959d2952d124 ("staging:iio: make iio_sw_buffer_preenable much more general.") introduced a restriction that requires that the set of channels that is passed to iio_buffer_register() is a subset of the channels assigned to the IIO device as the IIO core will use the list of channels that is assigned to the device to lookup a channel by scan index in iio_compute_scan_bytes(). If it can not find the channel the function will crash. This patch fixes the issue by making sure that the same set of channels is assigned to the IIO device and passed to iio_buffer_register(). Fixes the follow NULL pointer derefernce kernel crash: Unable to handle kernel NULL pointer dereference at virtual address 00000016 pgd = d53d0000 [00000016] *pgd=1534e831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] PREEMPT SMP ARM Modules linked in: CPU: 1 PID: 1626 Comm: bash Not tainted 3.15.0-19969-g2a180eb-dirty #9545 task: d6c124c0 ti: d539a000 task.ti: d539a000 PC is at iio_compute_scan_bytes+0x34/0xa8 LR is at iio_compute_scan_bytes+0x34/0xa8 pc : [] lr : [] psr: 60070013 sp : d539beb8 ip : 00000001 fp : 00000000 r10: 00000002 r9 : 00000000 r8 : 00000001 r7 : 00000000 r6 : d6dc8800 r5 : d7571000 r4 : 00000002 r3 : d7571000 r2 : 00000044 r1 : 00000001 r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 18c5387d Table: 153d004a DAC: 00000015 Process bash (pid: 1626, stack limit = 0xd539a240) Stack: (0xd539beb8 to 0xd539c000) bea0: c02fc0e4 d7571000 bec0: d76c1640 d6dc8800 d757117c 00000000 d757112c c0305b04 d76c1690 d76c1640 bee0: d7571188 00000002 00000000 d7571000 d539a000 00000000 000dd1c8 c0305d54 bf00: d7571010 0160b868 00000002 c69d3900 d7573278 d7573308 c69d3900 c01ece90 bf20: 00000002 c0103fac c0103f6c d539bf88 00000002 c69d3b00 c69d3b0c c0103468 bf40: 00000000 00000000 d7694a00 00000002 000af408 d539bf88 c000dd84 c00b2f94 bf60: d7694a00 000af408 00000002 d7694a00 d7694a00 00000002 000af408 c000dd84 bf80: 00000000 c00b32d0 00000000 00000000 00000002 b6f1aa78 00000002 000af408 bfa0: 00000004 c000dc00 b6f1aa78 00000002 00000001 000af408 00000002 00000000 bfc0: b6f1aa78 00000002 000af408 00000004 be806a4c 000a6094 00000000 000dd1c8 bfe0: 00000000 be8069cc b6e8ab77 b6ec125c 40070010 00000001 22940489 154a5007 [] (iio_compute_scan_bytes) from [] (__iio_update_buffers+0x248/0x438) [] (__iio_update_buffers) from [] (iio_buffer_store_enable+0x60/0x7c) [] (iio_buffer_store_enable) from [] (dev_attr_store+0x18/0x24) [] (dev_attr_store) from [] (sysfs_kf_write+0x40/0x4c) [] (sysfs_kf_write) from [] (kernfs_fop_write+0x110/0x154) [] (kernfs_fop_write) from [] (vfs_write+0xd0/0x160) [] (vfs_write) from [] (SyS_write+0x40/0x78) [] (SyS_write) from [] (ret_fast_syscall+0x0/0x30) Code: ea00000e e1a01008 e1a00005 ebfff6fc (e5d0a016) Fixes: 959d2952d124 ("staging:iio: make iio_sw_buffer_preenable much more general.") Signed-off-by: Lars-Peter Clausen Cc: Stable@vger.kernel.org Signed-off-by: Jonathan Cameron --- drivers/staging/iio/impedance-analyzer/ad5933.c | 11 ++++------- 1 file changed, 4 insertions(+), 7 deletions(-) diff --git a/drivers/staging/iio/impedance-analyzer/ad5933.c b/drivers/staging/iio/impedance-analyzer/ad5933.c index d0c89d0457d..9a6665dcf72 100644 --- a/drivers/staging/iio/impedance-analyzer/ad5933.c +++ b/drivers/staging/iio/impedance-analyzer/ad5933.c @@ -115,6 +115,7 @@ static const struct iio_chan_spec ad5933_channels[] = { .channel = 0, .info_mask_separate = BIT(IIO_CHAN_INFO_PROCESSED), .address = AD5933_REG_TEMP_DATA, + .scan_index = -1, .scan_type = { .sign = 's', .realbits = 14, @@ -125,8 +126,6 @@ static const struct iio_chan_spec ad5933_channels[] = { .indexed = 1, .channel = 0, .extend_name = "real_raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | - BIT(IIO_CHAN_INFO_SCALE), .address = AD5933_REG_REAL_DATA, .scan_index = 0, .scan_type = { @@ -139,8 +138,6 @@ static const struct iio_chan_spec ad5933_channels[] = { .indexed = 1, .channel = 0, .extend_name = "imag_raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | - BIT(IIO_CHAN_INFO_SCALE), .address = AD5933_REG_IMAG_DATA, .scan_index = 1, .scan_type = { @@ -749,14 +746,14 @@ static int ad5933_probe(struct i2c_client *client, indio_dev->name = id->name; indio_dev->modes = INDIO_DIRECT_MODE; indio_dev->channels = ad5933_channels; - indio_dev->num_channels = 1; /* only register temp0_input */ + indio_dev->num_channels = ARRAY_SIZE(ad5933_channels); ret = ad5933_register_ring_funcs_and_init(indio_dev); if (ret) goto error_disable_reg; - /* skip temp0_input, register in0_(real|imag)_raw */ - ret = iio_buffer_register(indio_dev, &ad5933_channels[1], 2); + ret = iio_buffer_register(indio_dev, ad5933_channels, + ARRAY_SIZE(ad5933_channels)); if (ret) goto error_unreg_ring; -- cgit v1.2.3-70-g09d2 From 97fb3033128958457f77456dc677a64bce8d33ae Mon Sep 17 00:00:00 2001 From: Lars-Peter Clausen Date: Thu, 25 Sep 2014 15:27:00 +0100 Subject: staging:iio:ad5933: Drop "raw" from channel names "raw" is the name of a channel property, but should not be part of the channel name itself. Signed-off-by: Lars-Peter Clausen Cc: Signed-off-by: Jonathan Cameron --- drivers/staging/iio/impedance-analyzer/ad5933.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/staging/iio/impedance-analyzer/ad5933.c b/drivers/staging/iio/impedance-analyzer/ad5933.c index 9a6665dcf72..b6bd609c365 100644 --- a/drivers/staging/iio/impedance-analyzer/ad5933.c +++ b/drivers/staging/iio/impedance-analyzer/ad5933.c @@ -125,7 +125,7 @@ static const struct iio_chan_spec ad5933_channels[] = { .type = IIO_VOLTAGE, .indexed = 1, .channel = 0, - .extend_name = "real_raw", + .extend_name = "real", .address = AD5933_REG_REAL_DATA, .scan_index = 0, .scan_type = { @@ -137,7 +137,7 @@ static const struct iio_chan_spec ad5933_channels[] = { .type = IIO_VOLTAGE, .indexed = 1, .channel = 0, - .extend_name = "imag_raw", + .extend_name = "imag", .address = AD5933_REG_IMAG_DATA, .scan_index = 1, .scan_type = { -- cgit v1.2.3-70-g09d2 From c6b4cac2d9cbe7891260b55b2871d269d89d1ae7 Mon Sep 17 00:00:00 2001 From: Robin van der Gracht Date: Mon, 29 Sep 2014 15:00:07 +0200 Subject: iio: st_sensors: Fix buffer copy Use byte_for_channel as iterator to properly initialize the buffer. Signed-off-by: Robin van der Gracht Acked-by: Denis Ciocca Signed-off-by: Jonathan Cameron Cc: --- drivers/iio/common/st_sensors/st_sensors_buffer.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/iio/common/st_sensors/st_sensors_buffer.c b/drivers/iio/common/st_sensors/st_sensors_buffer.c index 1665c8e4b62..e18bc678225 100644 --- a/drivers/iio/common/st_sensors/st_sensors_buffer.c +++ b/drivers/iio/common/st_sensors/st_sensors_buffer.c @@ -71,7 +71,7 @@ int st_sensors_get_buffer_element(struct iio_dev *indio_dev, u8 *buf) goto st_sensors_free_memory; } - for (i = 0; i < n * num_data_channels; i++) { + for (i = 0; i < n * byte_for_channel; i++) { if (i < n) buf[i] = rx_array[i]; else -- cgit v1.2.3-70-g09d2 From 4748119f1889b4ce96c84831ad0581598081b46f Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Sat, 4 Oct 2014 08:50:21 -0300 Subject: iio: adc: mxs-lradc: Disable the clock on probe failure We should disable lradc->clk in the case of errors in the probe function. Signed-off-by: Fabio Estevam Reviewed-by: Marek Vasut Signed-off-by: Jonathan Cameron Cc: --- drivers/staging/iio/adc/mxs-lradc.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) diff --git a/drivers/staging/iio/adc/mxs-lradc.c b/drivers/staging/iio/adc/mxs-lradc.c index 32a19264a17..2a29b9baec0 100644 --- a/drivers/staging/iio/adc/mxs-lradc.c +++ b/drivers/staging/iio/adc/mxs-lradc.c @@ -1559,14 +1559,16 @@ static int mxs_lradc_probe(struct platform_device *pdev) /* Grab all IRQ sources */ for (i = 0; i < of_cfg->irq_count; i++) { lradc->irq[i] = platform_get_irq(pdev, i); - if (lradc->irq[i] < 0) - return lradc->irq[i]; + if (lradc->irq[i] < 0) { + ret = lradc->irq[i]; + goto err_clk; + } ret = devm_request_irq(dev, lradc->irq[i], mxs_lradc_handle_irq, 0, of_cfg->irq_name[i], iio); if (ret) - return ret; + goto err_clk; } lradc->vref_mv = of_cfg->vref_mv; @@ -1588,7 +1590,7 @@ static int mxs_lradc_probe(struct platform_device *pdev) &mxs_lradc_trigger_handler, &mxs_lradc_buffer_ops); if (ret) - return ret; + goto err_clk; ret = mxs_lradc_trigger_init(iio); if (ret) @@ -1643,6 +1645,8 @@ err_dev: mxs_lradc_trigger_remove(iio); err_trig: iio_triggered_buffer_cleanup(iio); +err_clk: + clk_disable_unprepare(lradc->clk); return ret; } -- cgit v1.2.3-70-g09d2 From 03045bcf312961cc75b2719aad6b4d69907884db Mon Sep 17 00:00:00 2001 From: Dan Murphy Date: Mon, 20 Oct 2014 14:52:02 -0500 Subject: iio: tsl4531: Fix compiler error when CONFIG_PM_OPS is not defined MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Fix the compiler error when the CONFIG_PM_OPS flag is not set. drivers/iio/light/tsl4531.c:235:8: error: ‘tsl4531_suspend’ undeclared here (not in a function) drivers/iio/light/tsl4531.c:235:8: error: ‘tsl4531_resume’ undeclared here (not in a function) Signed-off-by: Dan Murphy Signed-off-by: Jonathan Cameron --- drivers/iio/light/tsl4531.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/drivers/iio/light/tsl4531.c b/drivers/iio/light/tsl4531.c index a15006efa13..0763b863257 100644 --- a/drivers/iio/light/tsl4531.c +++ b/drivers/iio/light/tsl4531.c @@ -230,9 +230,12 @@ static int tsl4531_resume(struct device *dev) return i2c_smbus_write_byte_data(to_i2c_client(dev), TSL4531_CONTROL, TSL4531_MODE_NORMAL); } -#endif static SIMPLE_DEV_PM_OPS(tsl4531_pm_ops, tsl4531_suspend, tsl4531_resume); +#define TSL4531_PM_OPS (&tsl4531_pm_ops) +#else +#define TSL4531_PM_OPS NULL +#endif static const struct i2c_device_id tsl4531_id[] = { { "tsl4531", 0 }, @@ -243,7 +246,7 @@ MODULE_DEVICE_TABLE(i2c, tsl4531_id); static struct i2c_driver tsl4531_driver = { .driver = { .name = TSL4531_DRV_NAME, - .pm = &tsl4531_pm_ops, + .pm = TSL4531_PM_OPS, .owner = THIS_MODULE, }, .probe = tsl4531_probe, -- cgit v1.2.3-70-g09d2 From 25afffe16d07909197f99163ca7cd1f80fb5cbdd Mon Sep 17 00:00:00 2001 From: Daniel Baluta Date: Fri, 10 Oct 2014 15:53:00 +0100 Subject: io: accel: kxcjk-1013: Fix iio_event_spec direction Because IIO_EV_DIR_* are not bitmasks but enums, IIO_EV_DIR_RISING | IIO_EV_DIR_FALLING is not equal with IIO_EV_DIR_EITHER. This could lead to potential misformatted sysfs attributes like: * in_accel_x_thresh_(null)_en * in_accel_x_thresh_(null)_period * in_accel_x_thresh_(null)_value or even memory corruption. Fixes: b4b491c083 (iio: accel: kxcjk-1013: Support threshold) Signed-off-by: Daniel Baluta Cc: Signed-off-by: Jonathan Cameron --- drivers/iio/accel/kxcjk-1013.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/iio/accel/kxcjk-1013.c b/drivers/iio/accel/kxcjk-1013.c index 98909a9e284..a23e58c4ed9 100644 --- a/drivers/iio/accel/kxcjk-1013.c +++ b/drivers/iio/accel/kxcjk-1013.c @@ -894,7 +894,7 @@ static const struct attribute_group kxcjk1013_attrs_group = { static const struct iio_event_spec kxcjk1013_event = { .type = IIO_EV_TYPE_THRESH, - .dir = IIO_EV_DIR_RISING | IIO_EV_DIR_FALLING, + .dir = IIO_EV_DIR_EITHER, .mask_separate = BIT(IIO_EV_INFO_VALUE) | BIT(IIO_EV_INFO_ENABLE) | BIT(IIO_EV_INFO_PERIOD) -- cgit v1.2.3-70-g09d2 From f73cde600d410ad4b31362a9c348016e40a146ea Mon Sep 17 00:00:00 2001 From: George McCollister Date: Fri, 31 Oct 2014 15:44:00 +0000 Subject: iio: as3935: allocate correct iio_device size Signed-off-by: George McCollister Acked-by: Hartmut Knaack Cc: Signed-off-by: Jonathan Cameron --- drivers/iio/proximity/as3935.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/iio/proximity/as3935.c b/drivers/iio/proximity/as3935.c index 5e780ef206f..8349cc0fdf6 100644 --- a/drivers/iio/proximity/as3935.c +++ b/drivers/iio/proximity/as3935.c @@ -330,7 +330,7 @@ static int as3935_probe(struct spi_device *spi) return -EINVAL; } - indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(st)); + indio_dev = devm_iio_device_alloc(&spi->dev, sizeof(*st)); if (!indio_dev) return -ENOMEM; -- cgit v1.2.3-70-g09d2 From e10554738cab4224e097c2f9d975ea781a4fcde4 Mon Sep 17 00:00:00 2001 From: Lars-Peter Clausen Date: Tue, 4 Nov 2014 18:03:14 +0100 Subject: staging:iio:ade7758: Fix NULL pointer deref when enabling buffer In older versions of the IIO framework it was possible to pass a completely different set of channels to iio_buffer_register() as the one that is assigned to the IIO device. Commit 959d2952d124 ("staging:iio: make iio_sw_buffer_preenable much more general.") introduced a restriction that requires that the set of channels that is passed to iio_buffer_register() is a subset of the channels assigned to the IIO device as the IIO core will use the list of channels that is assigned to the device to lookup a channel by scan index in iio_compute_scan_bytes(). If it can not find the channel the function will crash. This patch fixes the issue by making sure that the same set of channels is assigned to the IIO device and passed to iio_buffer_register(). Note that we need to remove the IIO_CHAN_INFO_RAW and IIO_CHAN_INFO_SCALE info attributes from the channels since we don't actually want those to be registered. Fixes the following crash: Unable to handle kernel NULL pointer dereference at virtual address 00000016 pgd = d2094000 [00000016] *pgd=16e39831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] PREEMPT SMP ARM Modules linked in: CPU: 1 PID: 1695 Comm: bash Not tainted 3.17.0-06329-g29461ee #9686 task: d7768040 ti: d5bd4000 task.ti: d5bd4000 PC is at iio_compute_scan_bytes+0x38/0xc0 LR is at iio_compute_scan_bytes+0x34/0xc0 pc : [] lr : [] psr: 60070013 sp : d5bd5ec0 ip : 00000000 fp : 00000000 r10: d769f934 r9 : 00000000 r8 : 00000001 r7 : 00000000 r6 : c8fc6240 r5 : d769f800 r4 : 00000000 r3 : d769f800 r2 : 00000000 r1 : ffffffff r0 : 00000000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 18c5387d Table: 1209404a DAC: 00000015 Process bash (pid: 1695, stack limit = 0xd5bd4240) Stack: (0xd5bd5ec0 to 0xd5bd6000) 5ec0: d769f800 d7435640 c8fc6240 d769f984 00000000 c03175a4 d7435690 d7435640 5ee0: d769f990 00000002 00000000 d769f800 d5bd4000 00000000 000b43a8 c03177f4 5f00: d769f810 0162b8c8 00000002 c8fc7e00 d77f1d08 d77f1da8 c8fc7e00 c01faf1c 5f20: 00000002 c010694c c010690c d5bd5f88 00000002 c8fc6840 c8fc684c c0105e08 5f40: 00000000 00000000 d20d1580 00000002 000af408 d5bd5f88 c000de84 c00b76d4 5f60: d20d1580 000af408 00000002 d20d1580 d20d1580 00000002 000af408 c000de84 5f80: 00000000 c00b7a44 00000000 00000000 00000002 b6ebea78 00000002 000af408 5fa0: 00000004 c000dd00 b6ebea78 00000002 00000001 000af408 00000002 00000000 5fc0: b6ebea78 00000002 000af408 00000004 bee96a4c 000a6094 00000000 000b43a8 5fe0: 00000000 bee969cc b6e2eb77 b6e6525c 40070010 00000001 00000000 00000000 [] (iio_compute_scan_bytes) from [] (__iio_update_buffers+0x248/0x438) [] (__iio_update_buffers) from [] (iio_buffer_store_enable+0x60/0x7c) [] (iio_buffer_store_enable) from [] (dev_attr_store+0x18/0x24) [] (dev_attr_store) from [] (sysfs_kf_write+0x40/0x4c) [] (sysfs_kf_write) from [] (kernfs_fop_write+0x110/0x154) [] (kernfs_fop_write) from [] (vfs_write+0xbc/0x170) [] (vfs_write) from [] (SyS_write+0x40/0x78) [] (SyS_write) from [] (ret_fast_syscall+0x0/0x30) Fixes: 959d2952d124 ("staging:iio: make iio_sw_buffer_preenable much more general.") Signed-off-by: Lars-Peter Clausen Cc: Signed-off-by: Jonathan Cameron --- drivers/staging/iio/meter/ade7758.h | 1 - drivers/staging/iio/meter/ade7758_core.c | 33 ++------------------------------ drivers/staging/iio/meter/ade7758_ring.c | 3 +-- 3 files changed, 3 insertions(+), 34 deletions(-) diff --git a/drivers/staging/iio/meter/ade7758.h b/drivers/staging/iio/meter/ade7758.h index 07318203a83..e8c98cf5707 100644 --- a/drivers/staging/iio/meter/ade7758.h +++ b/drivers/staging/iio/meter/ade7758.h @@ -119,7 +119,6 @@ struct ade7758_state { u8 *tx; u8 *rx; struct mutex buf_lock; - const struct iio_chan_spec *ade7758_ring_channels; struct spi_transfer ring_xfer[4]; struct spi_message ring_msg; /* diff --git a/drivers/staging/iio/meter/ade7758_core.c b/drivers/staging/iio/meter/ade7758_core.c index abc60067cd7..9eb79b7cb42 100644 --- a/drivers/staging/iio/meter/ade7758_core.c +++ b/drivers/staging/iio/meter/ade7758_core.c @@ -635,8 +635,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 0, .extend_name = "raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_A, AD7758_VOLTAGE), .scan_index = 0, .scan_type = { @@ -649,8 +647,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 0, .extend_name = "raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_A, AD7758_CURRENT), .scan_index = 1, .scan_type = { @@ -663,8 +659,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 0, .extend_name = "apparent_raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_A, AD7758_APP_PWR), .scan_index = 2, .scan_type = { @@ -677,8 +671,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 0, .extend_name = "active_raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_A, AD7758_ACT_PWR), .scan_index = 3, .scan_type = { @@ -691,8 +683,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 0, .extend_name = "reactive_raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_A, AD7758_REACT_PWR), .scan_index = 4, .scan_type = { @@ -705,8 +695,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 1, .extend_name = "raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_B, AD7758_VOLTAGE), .scan_index = 5, .scan_type = { @@ -719,8 +707,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 1, .extend_name = "raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_B, AD7758_CURRENT), .scan_index = 6, .scan_type = { @@ -733,8 +719,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 1, .extend_name = "apparent_raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_B, AD7758_APP_PWR), .scan_index = 7, .scan_type = { @@ -747,8 +731,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 1, .extend_name = "active_raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_B, AD7758_ACT_PWR), .scan_index = 8, .scan_type = { @@ -761,8 +743,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 1, .extend_name = "reactive_raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_B, AD7758_REACT_PWR), .scan_index = 9, .scan_type = { @@ -775,8 +755,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 2, .extend_name = "raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_C, AD7758_VOLTAGE), .scan_index = 10, .scan_type = { @@ -789,8 +767,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 2, .extend_name = "raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_C, AD7758_CURRENT), .scan_index = 11, .scan_type = { @@ -803,8 +779,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 2, .extend_name = "apparent_raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_C, AD7758_APP_PWR), .scan_index = 12, .scan_type = { @@ -817,8 +791,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 2, .extend_name = "active_raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_C, AD7758_ACT_PWR), .scan_index = 13, .scan_type = { @@ -831,8 +803,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .indexed = 1, .channel = 2, .extend_name = "reactive_raw", - .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), - .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), .address = AD7758_WT(AD7758_PHASE_C, AD7758_REACT_PWR), .scan_index = 14, .scan_type = { @@ -873,13 +843,14 @@ static int ade7758_probe(struct spi_device *spi) goto error_free_rx; } st->us = spi; - st->ade7758_ring_channels = &ade7758_channels[0]; mutex_init(&st->buf_lock); indio_dev->name = spi->dev.driver->name; indio_dev->dev.parent = &spi->dev; indio_dev->info = &ade7758_info; indio_dev->modes = INDIO_DIRECT_MODE; + indio_dev->channels = ade7758_channels; + indio_dev->num_channels = ARRAY_SIZE(ade7758_channels); ret = ade7758_configure_ring(indio_dev); if (ret) diff --git a/drivers/staging/iio/meter/ade7758_ring.c b/drivers/staging/iio/meter/ade7758_ring.c index c0accf8cce9..628e902dd81 100644 --- a/drivers/staging/iio/meter/ade7758_ring.c +++ b/drivers/staging/iio/meter/ade7758_ring.c @@ -85,7 +85,6 @@ static irqreturn_t ade7758_trigger_handler(int irq, void *p) **/ static int ade7758_ring_preenable(struct iio_dev *indio_dev) { - struct ade7758_state *st = iio_priv(indio_dev); unsigned channel; if (!bitmap_empty(indio_dev->active_scan_mask, indio_dev->masklength)) @@ -95,7 +94,7 @@ static int ade7758_ring_preenable(struct iio_dev *indio_dev) indio_dev->masklength); ade7758_write_waveform_type(&indio_dev->dev, - st->ade7758_ring_channels[channel].address); + indio_dev->channels[channel].address); return 0; } -- cgit v1.2.3-70-g09d2 From 79fa64eb2ee8ccb4bcad7f54caa2699730b10b22 Mon Sep 17 00:00:00 2001 From: Lars-Peter Clausen Date: Tue, 4 Nov 2014 18:03:15 +0100 Subject: staging:iio:ade7758: Fix check if channels are enabled in prenable We should check if a channel is enabled, not if no channels are enabled. Fixes: 550268ca1111 ("staging:iio: scrap scan_count and ensure all drivers use active_scan_mask") Signed-off-by: Lars-Peter Clausen Cc: Signed-off-by: Jonathan Cameron --- drivers/staging/iio/meter/ade7758_ring.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/staging/iio/meter/ade7758_ring.c b/drivers/staging/iio/meter/ade7758_ring.c index 628e902dd81..6e900649074 100644 --- a/drivers/staging/iio/meter/ade7758_ring.c +++ b/drivers/staging/iio/meter/ade7758_ring.c @@ -87,7 +87,7 @@ static int ade7758_ring_preenable(struct iio_dev *indio_dev) { unsigned channel; - if (!bitmap_empty(indio_dev->active_scan_mask, indio_dev->masklength)) + if (bitmap_empty(indio_dev->active_scan_mask, indio_dev->masklength)) return -EINVAL; channel = find_first_bit(indio_dev->active_scan_mask, -- cgit v1.2.3-70-g09d2 From b598aacc29331e7e638cd509108600e916c6331b Mon Sep 17 00:00:00 2001 From: Lars-Peter Clausen Date: Tue, 4 Nov 2014 18:03:16 +0100 Subject: staging:iio:ade7758: Remove "raw" from channel name "raw" is a property of a channel, but should not be part of the name of channel. Signed-off-by: Lars-Peter Clausen Cc: Signed-off-by: Jonathan Cameron --- drivers/staging/iio/meter/ade7758_core.c | 24 +++++++++--------------- 1 file changed, 9 insertions(+), 15 deletions(-) diff --git a/drivers/staging/iio/meter/ade7758_core.c b/drivers/staging/iio/meter/ade7758_core.c index 9eb79b7cb42..fb373b89dcc 100644 --- a/drivers/staging/iio/meter/ade7758_core.c +++ b/drivers/staging/iio/meter/ade7758_core.c @@ -634,7 +634,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_VOLTAGE, .indexed = 1, .channel = 0, - .extend_name = "raw", .address = AD7758_WT(AD7758_PHASE_A, AD7758_VOLTAGE), .scan_index = 0, .scan_type = { @@ -646,7 +645,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_CURRENT, .indexed = 1, .channel = 0, - .extend_name = "raw", .address = AD7758_WT(AD7758_PHASE_A, AD7758_CURRENT), .scan_index = 1, .scan_type = { @@ -658,7 +656,7 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_POWER, .indexed = 1, .channel = 0, - .extend_name = "apparent_raw", + .extend_name = "apparent", .address = AD7758_WT(AD7758_PHASE_A, AD7758_APP_PWR), .scan_index = 2, .scan_type = { @@ -670,7 +668,7 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_POWER, .indexed = 1, .channel = 0, - .extend_name = "active_raw", + .extend_name = "active", .address = AD7758_WT(AD7758_PHASE_A, AD7758_ACT_PWR), .scan_index = 3, .scan_type = { @@ -682,7 +680,7 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_POWER, .indexed = 1, .channel = 0, - .extend_name = "reactive_raw", + .extend_name = "reactive", .address = AD7758_WT(AD7758_PHASE_A, AD7758_REACT_PWR), .scan_index = 4, .scan_type = { @@ -694,7 +692,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_VOLTAGE, .indexed = 1, .channel = 1, - .extend_name = "raw", .address = AD7758_WT(AD7758_PHASE_B, AD7758_VOLTAGE), .scan_index = 5, .scan_type = { @@ -706,7 +703,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_CURRENT, .indexed = 1, .channel = 1, - .extend_name = "raw", .address = AD7758_WT(AD7758_PHASE_B, AD7758_CURRENT), .scan_index = 6, .scan_type = { @@ -718,7 +714,7 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_POWER, .indexed = 1, .channel = 1, - .extend_name = "apparent_raw", + .extend_name = "apparent", .address = AD7758_WT(AD7758_PHASE_B, AD7758_APP_PWR), .scan_index = 7, .scan_type = { @@ -730,7 +726,7 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_POWER, .indexed = 1, .channel = 1, - .extend_name = "active_raw", + .extend_name = "active", .address = AD7758_WT(AD7758_PHASE_B, AD7758_ACT_PWR), .scan_index = 8, .scan_type = { @@ -742,7 +738,7 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_POWER, .indexed = 1, .channel = 1, - .extend_name = "reactive_raw", + .extend_name = "reactive", .address = AD7758_WT(AD7758_PHASE_B, AD7758_REACT_PWR), .scan_index = 9, .scan_type = { @@ -754,7 +750,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_VOLTAGE, .indexed = 1, .channel = 2, - .extend_name = "raw", .address = AD7758_WT(AD7758_PHASE_C, AD7758_VOLTAGE), .scan_index = 10, .scan_type = { @@ -766,7 +761,6 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_CURRENT, .indexed = 1, .channel = 2, - .extend_name = "raw", .address = AD7758_WT(AD7758_PHASE_C, AD7758_CURRENT), .scan_index = 11, .scan_type = { @@ -778,7 +772,7 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_POWER, .indexed = 1, .channel = 2, - .extend_name = "apparent_raw", + .extend_name = "apparent", .address = AD7758_WT(AD7758_PHASE_C, AD7758_APP_PWR), .scan_index = 12, .scan_type = { @@ -790,7 +784,7 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_POWER, .indexed = 1, .channel = 2, - .extend_name = "active_raw", + .extend_name = "active", .address = AD7758_WT(AD7758_PHASE_C, AD7758_ACT_PWR), .scan_index = 13, .scan_type = { @@ -802,7 +796,7 @@ static const struct iio_chan_spec ade7758_channels[] = { .type = IIO_POWER, .indexed = 1, .channel = 2, - .extend_name = "reactive_raw", + .extend_name = "reactive", .address = AD7758_WT(AD7758_PHASE_C, AD7758_REACT_PWR), .scan_index = 14, .scan_type = { -- cgit v1.2.3-70-g09d2 From ab699bc792ddbfbe022c67debf6c56d81ff67a80 Mon Sep 17 00:00:00 2001 From: Olof Johansson Date: Tue, 4 Nov 2014 22:28:12 -0800 Subject: ARM: dts: vf610: add SD node to cosmic dts Driver has been there since a while back, but the dts never seems to have been updated with the node (nor pinctrl). Do so now. Cc: Matt Porter Acked-by: Shawn Guo Acked-by: Stefan Agner Signed-off-by: Olof Johansson --- arch/arm/boot/dts/vf610-cosmic.dts | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm/boot/dts/vf610-cosmic.dts b/arch/arm/boot/dts/vf610-cosmic.dts index 3fd1b74e121..de1b453c293 100644 --- a/arch/arm/boot/dts/vf610-cosmic.dts +++ b/arch/arm/boot/dts/vf610-cosmic.dts @@ -33,6 +33,13 @@ }; +&esdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc1>; + bus-width = <4>; + status = "okay"; +}; + &fec1 { phy-mode = "rmii"; pinctrl-names = "default"; @@ -42,6 +49,18 @@ &iomuxc { vf610-cosmic { + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + VF610_PAD_PTA24__ESDHC1_CLK 0x31ef + VF610_PAD_PTA25__ESDHC1_CMD 0x31ef + VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef + VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef + VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef + VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef + VF610_PAD_PTB28__GPIO_98 0x219d + >; + }; + pinctrl_fec1: fec1grp { fsl,pins = < VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2 -- cgit v1.2.3-70-g09d2 From ac0225f94f2af14d5db5a3ca2e9b151bb5488a52 Mon Sep 17 00:00:00 2001 From: Greg Kroah-Hartman Date: Wed, 5 Nov 2014 11:12:17 -0800 Subject: Revert "storage: Replace magic number with define in usb_stor_euscsi_init()" This reverts commit bda9893c50fb56253d3c206c14e3f933e5f68b3c as it was incorrect. Reported-by: Mark Knibbs Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/initializers.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/storage/initializers.c b/drivers/usb/storage/initializers.c index 4bc2fc98636..5a8b5ff1e45 100644 --- a/drivers/usb/storage/initializers.c +++ b/drivers/usb/storage/initializers.c @@ -52,7 +52,7 @@ int usb_stor_euscsi_init(struct us_data *us) us->iobuf[0] = 0x1; result = usb_stor_control_msg(us, us->send_ctrl_pipe, 0x0C, USB_RECIP_INTERFACE | USB_TYPE_VENDOR, - 0x01, 0x0, us->iobuf, 0x1, USB_CTRL_SET_TIMEOUT); + 0x01, 0x0, us->iobuf, 0x1, 5000); usb_stor_dbg(us, "-- result is %d\n", result); return 0; -- cgit v1.2.3-70-g09d2 From 4473d054ceb572557954f9536731d39b20937b0c Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Wed, 5 Nov 2014 18:41:59 +0100 Subject: USB: cdc-acm: only raise DTR on transitions from B0 Make sure to only raise DTR on transitions from B0 in set_termios. Also allow set_termios to be called from open with a termios_old of NULL. Note that DTR will not be raised prematurely in this case. Cc: stable Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index 6771f884cb8..9d6495424b0 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -985,11 +985,12 @@ static void acm_tty_set_termios(struct tty_struct *tty, /* FIXME: Needs to clear unsupported bits in the termios */ acm->clocal = ((termios->c_cflag & CLOCAL) != 0); - if (!newline.dwDTERate) { + if (C_BAUD(tty) == B0) { newline.dwDTERate = acm->line.dwDTERate; newctrl &= ~ACM_CTRL_DTR; - } else + } else if (termios_old && (termios_old->c_cflag & CBAUD) == B0) { newctrl |= ACM_CTRL_DTR; + } if (newctrl != acm->ctrlout) acm_set_control(acm, acm->ctrlout = newctrl); -- cgit v1.2.3-70-g09d2 From a88098bdb272fb631a59fb152bfef7c827531294 Mon Sep 17 00:00:00 2001 From: Mark Knibbs Date: Tue, 4 Nov 2014 13:00:24 +0000 Subject: USB: storage: Fix timeout in usb_stor_euscsi_init() and usb_stor_huawei_e220_init() The timeout argument to usb_stor_control_msg() is specified in jiffies, not milliseconds. Signed-off-by: Mark Knibbs Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/initializers.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/usb/storage/initializers.c b/drivers/usb/storage/initializers.c index 5a8b5ff1e45..73f125e0cb5 100644 --- a/drivers/usb/storage/initializers.c +++ b/drivers/usb/storage/initializers.c @@ -52,7 +52,7 @@ int usb_stor_euscsi_init(struct us_data *us) us->iobuf[0] = 0x1; result = usb_stor_control_msg(us, us->send_ctrl_pipe, 0x0C, USB_RECIP_INTERFACE | USB_TYPE_VENDOR, - 0x01, 0x0, us->iobuf, 0x1, 5000); + 0x01, 0x0, us->iobuf, 0x1, 5 * HZ); usb_stor_dbg(us, "-- result is %d\n", result); return 0; @@ -100,7 +100,7 @@ int usb_stor_huawei_e220_init(struct us_data *us) result = usb_stor_control_msg(us, us->send_ctrl_pipe, USB_REQ_SET_FEATURE, USB_TYPE_STANDARD | USB_RECIP_DEVICE, - 0x01, 0x0, NULL, 0x0, 1000); + 0x01, 0x0, NULL, 0x0, 1 * HZ); usb_stor_dbg(us, "Huawei mode set result is %d\n", result); return 0; } -- cgit v1.2.3-70-g09d2 From 32f638fc11db0526c706454d9ab4339d55ac89f3 Mon Sep 17 00:00:00 2001 From: Yinghai Lu Date: Thu, 30 Oct 2014 10:17:25 -0600 Subject: PCI: Don't oops on virtual buses in acpi_pci_get_bridge_handle() acpi_pci_get_bridge_handle() returns the ACPI handle for the bridge device (either a host bridge or a PCI-to-PCI bridge) leading to a PCI bus. But SR-IOV virtual functions can be on a virtual bus with no bridge leading to it. Return a NULL acpi_handle in this case instead of trying to dereference the NULL pointer to the bridge. This fixes a NULL pointer dereference oops in pci_get_hp_params() when adding SR-IOV VF devices on virtual buses. [bhelgaas: changelog, add comment in code] Fixes: 6cd33649fa83 ("PCI: Add pci_configure_device() during enumeration") Link: https://bugzilla.kernel.org/show_bug.cgi?id=87591 Reported-by: Chao Zhou Reported-by: Joerg Roedel Signed-off-by: Yinghai Lu Signed-off-by: Bjorn Helgaas --- include/linux/pci-acpi.h | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/include/linux/pci-acpi.h b/include/linux/pci-acpi.h index 64dacb7288a..24c7728ca68 100644 --- a/include/linux/pci-acpi.h +++ b/include/linux/pci-acpi.h @@ -41,8 +41,13 @@ static inline acpi_handle acpi_pci_get_bridge_handle(struct pci_bus *pbus) if (pci_is_root_bus(pbus)) dev = pbus->bridge; - else + else { + /* If pbus is a virtual bus, there is no bridge to it */ + if (!pbus->self) + return NULL; + dev = &pbus->self->dev; + } return ACPI_HANDLE(dev); } -- cgit v1.2.3-70-g09d2 From 7e8631e8b9d4e9f698c09c7e7309c96249180ff9 Mon Sep 17 00:00:00 2001 From: Al Viro Date: Wed, 5 Nov 2014 15:18:29 -0500 Subject: fix breakage in o2net_send_tcp_msg() uninitialized msghdr. Broken in "ocfs2: don't open-code kernel_recvmsg()" by me ;-/ Cc: stable@vger.kernel.org # 3.15+ Signed-off-by: Al Viro --- fs/ocfs2/cluster/tcp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/fs/ocfs2/cluster/tcp.c b/fs/ocfs2/cluster/tcp.c index 97de0fbd9f7..a9604400406 100644 --- a/fs/ocfs2/cluster/tcp.c +++ b/fs/ocfs2/cluster/tcp.c @@ -925,7 +925,7 @@ static int o2net_send_tcp_msg(struct socket *sock, struct kvec *vec, size_t veclen, size_t total) { int ret; - struct msghdr msg; + struct msghdr msg = {.msg_flags = 0,}; if (sock == NULL) { ret = -EINVAL; -- cgit v1.2.3-70-g09d2 From f20531a9aae0c7378d9fa75b4b5d99b7eecab066 Mon Sep 17 00:00:00 2001 From: Oussama Ghorbel Date: Tue, 4 Nov 2014 11:47:06 +0530 Subject: phy: omap-usb2: Enable runtime PM of omap-usb2 phy properly The USB OTG port does not work since v3.16 on omap platform. This is a regression introduced by the commit eb82a3d846fa (phy: omap-usb2: Balance pm_runtime_enable() on probe failure and remove). This because the call to pm_runtime_enable() function is moved after the call to devm_phy_create() function, which has side effect since later in the subsequent calls of devm_phy_create() there is a check with pm_runtime_enabled() to configure few things. Fixes: eb82a3d846fa Signed-off-by: Oussama Ghorbel Tested-by: Rabin Vincent Signed-off-by: Kishon Vijay Abraham I Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/phy/phy-omap-usb2.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/phy/phy-omap-usb2.c b/drivers/phy/phy-omap-usb2.c index 8c842980834..f091576b644 100644 --- a/drivers/phy/phy-omap-usb2.c +++ b/drivers/phy/phy-omap-usb2.c @@ -258,14 +258,16 @@ static int omap_usb2_probe(struct platform_device *pdev) otg->phy = &phy->phy; platform_set_drvdata(pdev, phy); + pm_runtime_enable(phy->dev); generic_phy = devm_phy_create(phy->dev, NULL, &ops, NULL); - if (IS_ERR(generic_phy)) + if (IS_ERR(generic_phy)) { + pm_runtime_disable(phy->dev); return PTR_ERR(generic_phy); + } phy_set_drvdata(generic_phy, phy); - pm_runtime_enable(phy->dev); phy_provider = devm_of_phy_provider_register(phy->dev, of_phy_simple_xlate); if (IS_ERR(phy_provider)) { -- cgit v1.2.3-70-g09d2 From f3f9185f3e49c748e952dd579357048a42e89398 Mon Sep 17 00:00:00 2001 From: Kailang Yang Date: Fri, 24 Oct 2014 15:43:46 +0800 Subject: ALSA: hda/realtek - Restore default value for ALC668 Restore the registers to prevent the abnormal digital power supply rising ratio/sequence to the codec and causing the incorrect default codec register restoration during initialization. Signed-off-by: Kailang Yang Signed-off-by: Takashi Iwai --- sound/pci/hda/patch_realtek.c | 40 ++++++++++++++++++++++++++++++++++++++-- 1 file changed, 38 insertions(+), 2 deletions(-) diff --git a/sound/pci/hda/patch_realtek.c b/sound/pci/hda/patch_realtek.c index 1af917f58a7..da03693099e 100644 --- a/sound/pci/hda/patch_realtek.c +++ b/sound/pci/hda/patch_realtek.c @@ -5669,6 +5669,35 @@ static void alc662_fixup_led_gpio1(struct hda_codec *codec, } } +static struct coef_fw alc668_coefs[] = { + WRITE_COEF(0x01, 0xbebe), WRITE_COEF(0x02, 0xaaaa), WRITE_COEF(0x03, 0x0), + WRITE_COEF(0x04, 0x0180), WRITE_COEF(0x06, 0x0), WRITE_COEF(0x07, 0x0f80), + WRITE_COEF(0x08, 0x0031), WRITE_COEF(0x0a, 0x0060), WRITE_COEF(0x0b, 0x0), + WRITE_COEF(0x0c, 0x7cf7), WRITE_COEF(0x0d, 0x1080), WRITE_COEF(0x0e, 0x7f7f), + WRITE_COEF(0x0f, 0xcccc), WRITE_COEF(0x10, 0xddcc), WRITE_COEF(0x11, 0x0001), + WRITE_COEF(0x13, 0x0), WRITE_COEF(0x14, 0x2aa0), WRITE_COEF(0x17, 0xa940), + WRITE_COEF(0x19, 0x0), WRITE_COEF(0x1a, 0x0), WRITE_COEF(0x1b, 0x0), + WRITE_COEF(0x1c, 0x0), WRITE_COEF(0x1d, 0x0), WRITE_COEF(0x1e, 0x7418), + WRITE_COEF(0x1f, 0x0804), WRITE_COEF(0x20, 0x4200), WRITE_COEF(0x21, 0x0468), + WRITE_COEF(0x22, 0x8ccc), WRITE_COEF(0x23, 0x0250), WRITE_COEF(0x24, 0x7418), + WRITE_COEF(0x27, 0x0), WRITE_COEF(0x28, 0x8ccc), WRITE_COEF(0x2a, 0xff00), + WRITE_COEF(0x2b, 0x8000), WRITE_COEF(0xa7, 0xff00), WRITE_COEF(0xa8, 0x8000), + WRITE_COEF(0xaa, 0x2e17), WRITE_COEF(0xab, 0xa0c0), WRITE_COEF(0xac, 0x0), + WRITE_COEF(0xad, 0x0), WRITE_COEF(0xae, 0x2ac6), WRITE_COEF(0xaf, 0xa480), + WRITE_COEF(0xb0, 0x0), WRITE_COEF(0xb1, 0x0), WRITE_COEF(0xb2, 0x0), + WRITE_COEF(0xb3, 0x0), WRITE_COEF(0xb4, 0x0), WRITE_COEF(0xb5, 0x1040), + WRITE_COEF(0xb6, 0xd697), WRITE_COEF(0xb7, 0x902b), WRITE_COEF(0xb8, 0xd697), + WRITE_COEF(0xb9, 0x902b), WRITE_COEF(0xba, 0xb8ba), WRITE_COEF(0xbb, 0xaaab), + WRITE_COEF(0xbc, 0xaaaf), WRITE_COEF(0xbd, 0x6aaa), WRITE_COEF(0xbe, 0x1c02), + WRITE_COEF(0xc0, 0x00ff), WRITE_COEF(0xc1, 0x0fa6), + {} +}; + +static void alc668_restore_default_value(struct hda_codec *codec) +{ + alc_process_coef_fw(codec, alc668_coefs); +} + enum { ALC662_FIXUP_ASPIRE, ALC662_FIXUP_LED_GPIO1, @@ -6136,8 +6165,15 @@ static int patch_alc662(struct hda_codec *codec) alc_fix_pll_init(codec, 0x20, 0x04, 15); - spec->init_hook = alc662_fill_coef; - alc662_fill_coef(codec); + switch (codec->vendor_id) { + case 0x10ec0668: + spec->init_hook = alc668_restore_default_value; + break; + default: + spec->init_hook = alc662_fill_coef; + alc662_fill_coef(codec); + break; + } snd_hda_pick_fixup(codec, alc662_fixup_models, alc662_fixup_tbl, alc662_fixups); -- cgit v1.2.3-70-g09d2 From 5305e4d674ed5ec9bebd11d948affd411594d4cf Mon Sep 17 00:00:00 2001 From: Arnd Bergmann Date: Fri, 24 Oct 2014 18:14:01 +0200 Subject: dma: edma: move device registration to platform code The horrible split between the low-level part of the edma support and the dmaengine front-end driver causes problems on multiplatform kernels. This is an attempt to improve the situation slightly by only registering the dmaengine devices that are actually present. Signed-off-by: Arnd Bergmann [olof: add missing include of linux/dma-mapping.h] Signed-off-by: Olof Johansson Signed-off-by: Olof Johansson --- arch/arm/common/edma.c | 9 +++++++++ drivers/dma/edma.c | 40 +--------------------------------------- 2 files changed, 10 insertions(+), 39 deletions(-) diff --git a/arch/arm/common/edma.c b/arch/arm/common/edma.c index d86771abbf5..72041f002b7 100644 --- a/arch/arm/common/edma.c +++ b/arch/arm/common/edma.c @@ -26,6 +26,7 @@ #include #include #include +#include #include #include #include @@ -1623,6 +1624,11 @@ static int edma_probe(struct platform_device *pdev) struct device_node *node = pdev->dev.of_node; struct device *dev = &pdev->dev; int ret; + struct platform_device_info edma_dev_info = { + .name = "edma-dma-engine", + .dma_mask = DMA_BIT_MASK(32), + .parent = &pdev->dev, + }; if (node) { /* Check if this is a second instance registered */ @@ -1793,6 +1799,9 @@ static int edma_probe(struct platform_device *pdev) edma_write_array(j, EDMA_QRAE, i, 0x0); } arch_num_cc++; + + edma_dev_info.id = j; + platform_device_register_full(&edma_dev_info); } return 0; diff --git a/drivers/dma/edma.c b/drivers/dma/edma.c index 123f578d6dd..4cfaaa5a49b 100644 --- a/drivers/dma/edma.c +++ b/drivers/dma/edma.c @@ -1107,52 +1107,14 @@ bool edma_filter_fn(struct dma_chan *chan, void *param) } EXPORT_SYMBOL(edma_filter_fn); -static struct platform_device *pdev0, *pdev1; - -static const struct platform_device_info edma_dev_info0 = { - .name = "edma-dma-engine", - .id = 0, - .dma_mask = DMA_BIT_MASK(32), -}; - -static const struct platform_device_info edma_dev_info1 = { - .name = "edma-dma-engine", - .id = 1, - .dma_mask = DMA_BIT_MASK(32), -}; - static int edma_init(void) { - int ret = platform_driver_register(&edma_driver); - - if (ret == 0) { - pdev0 = platform_device_register_full(&edma_dev_info0); - if (IS_ERR(pdev0)) { - platform_driver_unregister(&edma_driver); - ret = PTR_ERR(pdev0); - goto out; - } - } - - if (!of_have_populated_dt() && EDMA_CTLRS == 2) { - pdev1 = platform_device_register_full(&edma_dev_info1); - if (IS_ERR(pdev1)) { - platform_driver_unregister(&edma_driver); - platform_device_unregister(pdev0); - ret = PTR_ERR(pdev1); - } - } - -out: - return ret; + return platform_driver_register(&edma_driver); } subsys_initcall(edma_init); static void __exit edma_exit(void) { - platform_device_unregister(pdev0); - if (pdev1) - platform_device_unregister(pdev1); platform_driver_unregister(&edma_driver); } module_exit(edma_exit); -- cgit v1.2.3-70-g09d2 From cd92208f6996f7d190a15eb278e7d02499e2d264 Mon Sep 17 00:00:00 2001 From: Matthias Brugger Date: Thu, 9 Oct 2014 18:23:31 +0200 Subject: tty: serial: 8250_mtk: Fix quot calculation The calculation of value quot for highspeed register set to three was wrong. This patch fixes the calculation so that the serial port for baudrates bigger then 576000 baud is working correctly. Signed-off-by: Matthias Brugger Signed-off-by: Greg Kroah-Hartman --- drivers/tty/serial/8250/8250_mtk.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/tty/serial/8250/8250_mtk.c b/drivers/tty/serial/8250/8250_mtk.c index 8f37d57165e..de7aae523b3 100644 --- a/drivers/tty/serial/8250/8250_mtk.c +++ b/drivers/tty/serial/8250/8250_mtk.c @@ -81,7 +81,7 @@ mtk8250_set_termios(struct uart_port *port, struct ktermios *termios, /* Set to highest baudrate supported */ if (baud >= 1152000) baud = 921600; - quot = DIV_ROUND_CLOSEST(port->uartclk, 256 * baud); + quot = (port->uartclk / (256 * baud)) + 1; } /* -- cgit v1.2.3-70-g09d2 From 9e326f78713a4421fe11afc2ddeac07698fac131 Mon Sep 17 00:00:00 2001 From: Imre Deak Date: Thu, 2 Oct 2014 16:34:31 +0300 Subject: tty/vt: don't set font mappings on vc not supporting this We can call this function for a dummy console that doesn't support setting the font mapping, which will result in a null ptr BUG. So check for this case and return error for consoles w/o font mapping support. Reference: https://bugzilla.kernel.org/show_bug.cgi?id=59321 Signed-off-by: Imre Deak Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/tty/vt/consolemap.c | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/drivers/tty/vt/consolemap.c b/drivers/tty/vt/consolemap.c index 610b720d3b9..59b25e03996 100644 --- a/drivers/tty/vt/consolemap.c +++ b/drivers/tty/vt/consolemap.c @@ -539,6 +539,12 @@ int con_set_unimap(struct vc_data *vc, ushort ct, struct unipair __user *list) /* Save original vc_unipagdir_loc in case we allocate a new one */ p = *vc->vc_uni_pagedir_loc; + + if (!p) { + err = -EINVAL; + + goto out_unlock; + } if (p->refcount > 1) { int j, k; @@ -623,6 +629,7 @@ int con_set_unimap(struct vc_data *vc, ushort ct, struct unipair __user *list) set_inverse_transl(vc, p, i); /* Update inverse translations */ set_inverse_trans_unicode(vc, p); +out_unlock: console_unlock(); return err; } -- cgit v1.2.3-70-g09d2 From 7e12e675c17982a8b3cc91314a68f4c4d1bceb92 Mon Sep 17 00:00:00 2001 From: Jingchang Lu Date: Tue, 21 Oct 2014 16:50:21 +0800 Subject: serial: of-serial: fix uninitialized kmalloc variable The info pointer points to an uninitialized kmalloced space. If a device doesn't have clk property, then info->clk may have unpredicated value and cause call trace. So use kzalloc to make sure it is NULL initialized. Signed-off-by: Jingchang Lu Acked-by: Arnd Bergmann --- drivers/tty/serial/of_serial.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c index 8bc2563335a..56982da4a9e 100644 --- a/drivers/tty/serial/of_serial.c +++ b/drivers/tty/serial/of_serial.c @@ -158,7 +158,7 @@ static int of_platform_serial_probe(struct platform_device *ofdev) if (of_find_property(ofdev->dev.of_node, "used-by-rtas", NULL)) return -EBUSY; - info = kmalloc(sizeof(*info), GFP_KERNEL); + info = kzalloc(sizeof(*info), GFP_KERNEL); if (info == NULL) return -ENOMEM; -- cgit v1.2.3-70-g09d2 From 2b9375b91bef65b837bed61a05fb387159b38ddf Mon Sep 17 00:00:00 2001 From: Dmitry Eremin-Solenikov Date: Thu, 6 Nov 2014 14:08:29 +0300 Subject: spi: pxa2xx: toggle clocks on suspend if not disabled by runtime PM If PM_RUNTIME is enabled, it is easy to trigger the following backtrace on pxa2xx hosts: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1 at /home/lumag/linux/arch/arm/mach-pxa/clock.c:35 clk_disable+0xa0/0xa8() Modules linked in: CPU: 0 PID: 1 Comm: swapper Not tainted 3.17.0-00007-g1b3d2ee-dirty #104 [] (unwind_backtrace) from [] (show_stack+0x10/0x14) [] (show_stack) from [] (warn_slowpath_common+0x6c/0x8c) [] (warn_slowpath_common) from [] (warn_slowpath_null+0x1c/0x24) [] (warn_slowpath_null) from [] (clk_disable+0xa0/0xa8) [] (clk_disable) from [] (pxa2xx_spi_suspend+0x2c/0x34) [] (pxa2xx_spi_suspend) from [] (platform_pm_suspend+0x2c/0x54) [] (platform_pm_suspend) from [] (dpm_run_callback.isra.14+0x2c/0x74) [] (dpm_run_callback.isra.14) from [] (__device_suspend+0x120/0x2f8) [] (__device_suspend) from [] (dpm_suspend+0x50/0x208) [] (dpm_suspend) from [] (suspend_devices_and_enter+0x8c/0x3a0) [] (suspend_devices_and_enter) from [] (pm_suspend+0x214/0x2a8) [] (pm_suspend) from [] (test_suspend+0x14c/0x1dc) [] (test_suspend) from [] (do_one_initcall+0x8c/0x1fc) [] (do_one_initcall) from [] (kernel_init_freeable+0xf4/0x1b4) [] (kernel_init_freeable) from [] (kernel_init+0x8/0xec) [] (kernel_init) from [] (ret_from_fork+0x14/0x24) ---[ end trace 46524156d8faa4f6 ]--- This happens because suspend function tries to disable a clock that is already disabled by runtime_suspend callback. Add if (!pm_runtime_suspended()) checks to suspend/resume path. Fixes: 7d94a505858 (spi/pxa2xx: add support for runtime PM) Signed-off-by: Dmitry Eremin-Solenikov Reported-by: Andrea Adami Signed-off-by: Mark Brown Cc: stable@vger.kernel.org --- drivers/spi/spi-pxa2xx.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c index d8a105f7683..9e9e0f971e6 100644 --- a/drivers/spi/spi-pxa2xx.c +++ b/drivers/spi/spi-pxa2xx.c @@ -1274,7 +1274,9 @@ static int pxa2xx_spi_suspend(struct device *dev) if (status != 0) return status; write_SSCR0(0, drv_data->ioaddr); - clk_disable_unprepare(ssp->clk); + + if (!pm_runtime_suspended(dev)) + clk_disable_unprepare(ssp->clk); return 0; } @@ -1288,7 +1290,8 @@ static int pxa2xx_spi_resume(struct device *dev) pxa2xx_spi_dma_resume(drv_data); /* Enable the SSP clock */ - clk_prepare_enable(ssp->clk); + if (!pm_runtime_suspended(dev)) + clk_prepare_enable(ssp->clk); /* Restore LPSS private register bits */ lpss_ssp_setup(drv_data); -- cgit v1.2.3-70-g09d2 From 491a48aa52f03b4654edbf8f97c1aa7d2f24f62e Mon Sep 17 00:00:00 2001 From: Isamu Mogi Date: Thu, 30 Oct 2014 22:07:36 +0900 Subject: MIPS: R3000: Fix debug output for Virtual page number Virtual page number of R3000 in entryhi is 20 bit from MSB. But in dump_tlb(), the bit mask to read it from entryhi is 19 bit (0xffffe000). The patch fixes that to 0xfffff000. Signed-off-by: Isamu Mogi Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/8290/ Signed-off-by: Ralf Baechle --- arch/mips/lib/r3k_dump_tlb.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/mips/lib/r3k_dump_tlb.c b/arch/mips/lib/r3k_dump_tlb.c index 91615c2ef0c..1ef365ab3cd 100644 --- a/arch/mips/lib/r3k_dump_tlb.c +++ b/arch/mips/lib/r3k_dump_tlb.c @@ -34,7 +34,7 @@ static void dump_tlb(int first, int last) entrylo0 = read_c0_entrylo0(); /* Unused entries have a virtual address of KSEG0. */ - if ((entryhi & 0xffffe000) != 0x80000000 + if ((entryhi & 0xfffff000) != 0x80000000 && (entryhi & 0xfc0) == asid) { /* * Only print entries in use @@ -43,7 +43,7 @@ static void dump_tlb(int first, int last) printk("va=%08lx asid=%08lx" " [pa=%06lx n=%d d=%d v=%d g=%d]", - (entryhi & 0xffffe000), + (entryhi & 0xfffff000), entryhi & 0xfc0, entrylo0 & PAGE_MASK, (entrylo0 & (1 << 11)) ? 1 : 0, -- cgit v1.2.3-70-g09d2 From c4dc304677e8d566572c4738d95c48be150c6606 Mon Sep 17 00:00:00 2001 From: Francesco Ruggeri Date: Fri, 10 Oct 2014 13:09:53 -0700 Subject: tty: Fix pty master poll() after slave closes v2 Commit f95499c3030f ("n_tty: Don't wait for buffer work in read() loop") introduces a race window where a pty master can be signalled that the pty slave was closed before all the data that the slave wrote is delivered. Commit f8747d4a466a ("tty: Fix pty master read() after slave closes") fixed the problem in case of n_tty_read, but the problem still exists for n_tty_poll. This can be seen by running 'for ((i=0; i<100;i++));do ./test.py ;done' where test.py is: import os, select, pty (pid, pty_fd) = pty.fork() if pid == 0: os.write(1, 'This string should be received by parent') else: poller = select.epoll() poller.register( pty_fd, select.EPOLLIN ) ready = poller.poll( 1 * 1000 ) for fd, events in ready: if not events & select.EPOLLIN: print 'missed POLLIN event' else: print os.read(fd, 100) poller.close() The string from the slave is missed several times. This patch takes the same approach as the fix for read and special cases this condition for poll. Tested on 3.16. Signed-off-by: Francesco Ruggeri Signed-off-by: Greg Kroah-Hartman --- drivers/tty/n_tty.c | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) diff --git a/drivers/tty/n_tty.c b/drivers/tty/n_tty.c index 89c4cee253e..2e900a98c3e 100644 --- a/drivers/tty/n_tty.c +++ b/drivers/tty/n_tty.c @@ -2413,12 +2413,17 @@ static unsigned int n_tty_poll(struct tty_struct *tty, struct file *file, poll_wait(file, &tty->read_wait, wait); poll_wait(file, &tty->write_wait, wait); + if (test_bit(TTY_OTHER_CLOSED, &tty->flags)) + mask |= POLLHUP; if (input_available_p(tty, 1)) mask |= POLLIN | POLLRDNORM; + else if (mask & POLLHUP) { + tty_flush_to_ldisc(tty); + if (input_available_p(tty, 1)) + mask |= POLLIN | POLLRDNORM; + } if (tty->packet && tty->link->ctrl_status) mask |= POLLPRI | POLLIN | POLLRDNORM; - if (test_bit(TTY_OTHER_CLOSED, &tty->flags)) - mask |= POLLHUP; if (tty_hung_up_p(file)) mask |= POLLHUP; if (!(mask & (POLLHUP | POLLIN | POLLRDNORM))) { -- cgit v1.2.3-70-g09d2 From 2a8cdfde9237c4e1bd7c2e68c415b006491d23cc Mon Sep 17 00:00:00 2001 From: Johan Hovold Date: Thu, 6 Nov 2014 18:08:33 +0100 Subject: USB: cdc-acm: add quirk for control-line state requests Add new quirk for devices that cannot handle control-line state requests. Note that we currently send these requests to all devices, regardless of whether they claim to support it, but that errors are only logged if support is claimed. Since commit 0943d8ead30e ("USB: cdc-acm: use tty-port dtr_rts"), which only changed the timings for these requests slightly, this has been reported to cause occasional firmware crashes on Simtec Electronics Entropy Key devices after re-enumeration. Enable the quirk for this device. Reported-by: Nix Tested-by: Nix Cc: stable # v3.16 Signed-off-by: Johan Hovold Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-acm.c | 14 ++++++++++++-- drivers/usb/class/cdc-acm.h | 2 ++ 2 files changed, 14 insertions(+), 2 deletions(-) diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c index 9d6495424b0..077d58ac3dc 100644 --- a/drivers/usb/class/cdc-acm.c +++ b/drivers/usb/class/cdc-acm.c @@ -148,8 +148,15 @@ static int acm_ctrl_msg(struct acm *acm, int request, int value, /* devices aren't required to support these requests. * the cdc acm descriptor tells whether they do... */ -#define acm_set_control(acm, control) \ - acm_ctrl_msg(acm, USB_CDC_REQ_SET_CONTROL_LINE_STATE, control, NULL, 0) +static inline int acm_set_control(struct acm *acm, int control) +{ + if (acm->quirks & QUIRK_CONTROL_LINE_STATE) + return -EOPNOTSUPP; + + return acm_ctrl_msg(acm, USB_CDC_REQ_SET_CONTROL_LINE_STATE, + control, NULL, 0); +} + #define acm_set_line(acm, line) \ acm_ctrl_msg(acm, USB_CDC_REQ_SET_LINE_CODING, 0, line, sizeof *(line)) #define acm_send_break(acm, ms) \ @@ -1320,6 +1327,7 @@ made_compressed_probe: tty_port_init(&acm->port); acm->port.ops = &acm_port_ops; init_usb_anchor(&acm->delayed); + acm->quirks = quirks; buf = usb_alloc_coherent(usb_dev, ctrlsize, GFP_KERNEL, &acm->ctrl_dma); if (!buf) { @@ -1687,6 +1695,8 @@ static const struct usb_device_id acm_ids[] = { { USB_DEVICE(0x0572, 0x1328), /* Shiro / Aztech USB MODEM UM-3100 */ .driver_info = NO_UNION_NORMAL, /* has no union descriptor */ }, + { USB_DEVICE(0x20df, 0x0001), /* Simtec Electronics Entropy Key */ + .driver_info = QUIRK_CONTROL_LINE_STATE, }, { USB_DEVICE(0x2184, 0x001c) }, /* GW Instek AFG-2225 */ { USB_DEVICE(0x22b8, 0x6425), /* Motorola MOTOMAGX phones */ }, diff --git a/drivers/usb/class/cdc-acm.h b/drivers/usb/class/cdc-acm.h index fc75651afe1..d3251ebd09e 100644 --- a/drivers/usb/class/cdc-acm.h +++ b/drivers/usb/class/cdc-acm.h @@ -121,6 +121,7 @@ struct acm { unsigned int throttle_req:1; /* throttle requested */ u8 bInterval; struct usb_anchor delayed; /* writes queued for a device about to be woken */ + unsigned long quirks; }; #define CDC_DATA_INTERFACE_TYPE 0x0a @@ -132,3 +133,4 @@ struct acm { #define NOT_A_MODEM BIT(3) #define NO_DATA_INTERFACE BIT(4) #define IGNORE_DEVICE BIT(5) +#define QUIRK_CONTROL_LINE_STATE BIT(6) -- cgit v1.2.3-70-g09d2 From 77783d06427293b2d711c45cfd4abc6494a1af9c Mon Sep 17 00:00:00 2001 From: Jan Kara Date: Fri, 7 Nov 2014 08:29:25 +1100 Subject: mm: Fix comment before truncate_setsize() XFS doesn't always hold i_mutex when calling truncate_setsize() and it uses a different lock to serialize truncates and writes. So fix the comment before truncate_setsize(). Reported-by: Jan Beulich Signed-off-by: Jan Kara Signed-off-by: Dave Chinner --- mm/truncate.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/mm/truncate.c b/mm/truncate.c index c646084e5ee..f1e4d605236 100644 --- a/mm/truncate.c +++ b/mm/truncate.c @@ -715,8 +715,9 @@ EXPORT_SYMBOL(truncate_pagecache); * necessary) to @newsize. It will be typically be called from the filesystem's * setattr function when ATTR_SIZE is passed in. * - * Must be called with inode_mutex held and before all filesystem specific - * block truncation has been performed. + * Must be called with a lock serializing truncates and writes (generally + * i_mutex but e.g. xfs uses a different lock) and before all filesystem + * specific block truncation has been performed. */ void truncate_setsize(struct inode *inode, loff_t newsize) { -- cgit v1.2.3-70-g09d2 From afa947cb52a8e73fe71915a0b0af6fcf98dfbe1a Mon Sep 17 00:00:00 2001 From: Dave Chinner Date: Fri, 7 Nov 2014 08:29:57 +1100 Subject: xfs: bulkstat btree walk doesn't terminate The bulkstat code has several different ways of detecting the end of an AG when doing a walk. They are not consistently detected, and the code that checks for the end of AG conditions is not consistently coded. Hence the are conditions where the walk code can get stuck in an endless loop making no progress and not triggering any termination conditions. Convert all the "tmp/i" status return codes from btree operations to a common name (stat) and apply end-of-ag detection to these operations consistently. cc: # 3.17 Signed-off-by: Dave Chinner Reviewed-by: Brian Foster Signed-off-by: Dave Chinner --- fs/xfs/xfs_itable.c | 19 ++++++++++--------- 1 file changed, 10 insertions(+), 9 deletions(-) diff --git a/fs/xfs/xfs_itable.c b/fs/xfs/xfs_itable.c index 7765ff743e9..16737cbbee1 100644 --- a/fs/xfs/xfs_itable.c +++ b/fs/xfs/xfs_itable.c @@ -356,7 +356,6 @@ xfs_bulkstat( int end_of_ag; /* set if we've seen the ag end */ int error; /* error code */ int fmterror;/* bulkstat formatter result */ - int i; /* loop index */ int icount; /* count of inodes good in irbuf */ size_t irbsize; /* size of irec buffer in bytes */ xfs_ino_t ino; /* inode number (filesystem) */ @@ -366,11 +365,11 @@ xfs_bulkstat( xfs_ino_t lastino; /* last inode number returned */ int nirbuf; /* size of irbuf */ int rval; /* return value error code */ - int tmp; /* result value from btree calls */ int ubcount; /* size of user's buffer */ int ubleft; /* bytes left in user's buffer */ char __user *ubufp; /* pointer into user's buffer */ int ubelem; /* spaces used in user's buffer */ + int stat; /* * Get the last inode value, see if there's nothing to do. @@ -436,13 +435,15 @@ xfs_bulkstat( agino = r.ir_startino + XFS_INODES_PER_CHUNK; } /* Increment to the next record */ - error = xfs_btree_increment(cur, 0, &tmp); + error = xfs_btree_increment(cur, 0, &stat); } else { /* Start of ag. Lookup the first inode chunk */ - error = xfs_inobt_lookup(cur, 0, XFS_LOOKUP_GE, &tmp); + error = xfs_inobt_lookup(cur, 0, XFS_LOOKUP_GE, &stat); } - if (error) + if (error || stat == 0) { + end_of_ag = 1; goto del_cursor; + } /* * Loop through inode btree records in this ag, @@ -451,8 +452,8 @@ xfs_bulkstat( while (irbp < irbufend && icount < ubcount) { struct xfs_inobt_rec_incore r; - error = xfs_inobt_get_rec(cur, &r, &i); - if (error || i == 0) { + error = xfs_inobt_get_rec(cur, &r, &stat); + if (error || stat == 0) { end_of_ag = 1; goto del_cursor; } @@ -473,8 +474,8 @@ xfs_bulkstat( * Set agino to after this chunk and bump the cursor. */ agino = r.ir_startino + XFS_INODES_PER_CHUNK; - error = xfs_btree_increment(cur, 0, &tmp); - if (error) { + error = xfs_btree_increment(cur, 0, &stat); + if (error || stat == 0) { end_of_ag = 1; goto del_cursor; } -- cgit v1.2.3-70-g09d2 From bf4a5af20d25ecc8876978ad34b8db83b4235f3c Mon Sep 17 00:00:00 2001 From: Dave Chinner Date: Fri, 7 Nov 2014 08:30:30 +1100 Subject: xfs: bulkstat chunk formatting cursor is broken The xfs_bulkstat_agichunk formatting cursor takes buffer values from the main loop and passes them via the structure to the chunk formatter, and the writes the changed values back into the main loop local variables. Unfortunately, this complex dance is full of corner cases that aren't handled correctly. The biggest problem is that it is double handling the information in both the main loop and the chunk formatting function, leading to inconsistent updates and endless loops where progress is not made. To fix this, push the struct xfs_bulkstat_agichunk outwards to be the primary holder of user buffer information. this removes the double handling in the main loop. Also, pass the last inode processed by the chunk formatter as a separate parameter as it purely an output variable and is not related to the user buffer consumption cursor. Finally, the chunk formatting code is not shared by anyone, so make it local to xfs_itable.c. cc: # 3.17 Signed-off-by: Dave Chinner Reviewed-by: Brian Foster Signed-off-by: Dave Chinner --- fs/xfs/xfs_itable.c | 59 +++++++++++++++++++++++++---------------------------- fs/xfs/xfs_itable.h | 16 --------------- 2 files changed, 28 insertions(+), 47 deletions(-) diff --git a/fs/xfs/xfs_itable.c b/fs/xfs/xfs_itable.c index 16737cbbee1..50a3e5995dd 100644 --- a/fs/xfs/xfs_itable.c +++ b/fs/xfs/xfs_itable.c @@ -262,20 +262,26 @@ xfs_bulkstat_grab_ichunk( #define XFS_BULKSTAT_UBLEFT(ubleft) ((ubleft) >= statstruct_size) +struct xfs_bulkstat_agichunk { + char __user **ac_ubuffer;/* pointer into user's buffer */ + int ac_ubleft; /* bytes left in user's buffer */ + int ac_ubelem; /* spaces used in user's buffer */ +}; + /* * Process inodes in chunk with a pointer to a formatter function * that will iget the inode and fill in the appropriate structure. */ -int +static int xfs_bulkstat_ag_ichunk( struct xfs_mount *mp, xfs_agnumber_t agno, struct xfs_inobt_rec_incore *irbp, bulkstat_one_pf formatter, size_t statstruct_size, - struct xfs_bulkstat_agichunk *acp) + struct xfs_bulkstat_agichunk *acp, + xfs_ino_t *lastino) { - xfs_ino_t lastino = acp->ac_lastino; char __user **ubufp = acp->ac_ubuffer; int ubleft = acp->ac_ubleft; int ubelem = acp->ac_ubelem; @@ -295,7 +301,7 @@ xfs_bulkstat_ag_ichunk( /* Skip if this inode is free */ if (XFS_INOBT_MASK(chunkidx) & irbp->ir_free) { - lastino = ino; + *lastino = ino; continue; } @@ -313,7 +319,7 @@ xfs_bulkstat_ag_ichunk( ubleft = 0; break; } - lastino = ino; + *lastino = ino; continue; } if (fmterror == BULKSTAT_RV_GIVEUP) { @@ -325,10 +331,9 @@ xfs_bulkstat_ag_ichunk( *ubufp += ubused; ubleft -= ubused; ubelem++; - lastino = ino; + *lastino = ino; } - acp->ac_lastino = lastino; acp->ac_ubleft = ubleft; acp->ac_ubelem = ubelem; @@ -355,7 +360,6 @@ xfs_bulkstat( xfs_btree_cur_t *cur; /* btree cursor for ialloc btree */ int end_of_ag; /* set if we've seen the ag end */ int error; /* error code */ - int fmterror;/* bulkstat formatter result */ int icount; /* count of inodes good in irbuf */ size_t irbsize; /* size of irec buffer in bytes */ xfs_ino_t ino; /* inode number (filesystem) */ @@ -366,10 +370,8 @@ xfs_bulkstat( int nirbuf; /* size of irbuf */ int rval; /* return value error code */ int ubcount; /* size of user's buffer */ - int ubleft; /* bytes left in user's buffer */ - char __user *ubufp; /* pointer into user's buffer */ - int ubelem; /* spaces used in user's buffer */ int stat; + struct xfs_bulkstat_agichunk ac; /* * Get the last inode value, see if there's nothing to do. @@ -386,11 +388,13 @@ xfs_bulkstat( } ubcount = *ubcountp; /* statstruct's */ - ubleft = ubcount * statstruct_size; /* bytes */ - *ubcountp = ubelem = 0; + ac.ac_ubuffer = &ubuffer; + ac.ac_ubleft = ubcount * statstruct_size; /* bytes */; + ac.ac_ubelem = 0; + + *ubcountp = 0; *done = 0; - fmterror = 0; - ubufp = ubuffer; + irbuf = kmem_zalloc_greedy(&irbsize, PAGE_SIZE, PAGE_SIZE * 4); if (!irbuf) return -ENOMEM; @@ -402,7 +406,7 @@ xfs_bulkstat( * inode returned; 0 means start of the allocation group. */ rval = 0; - while (XFS_BULKSTAT_UBLEFT(ubleft) && agno < mp->m_sb.sb_agcount) { + while (XFS_BULKSTAT_UBLEFT(ac.ac_ubleft) && agno < mp->m_sb.sb_agcount) { cond_resched(); error = xfs_ialloc_read_agi(mp, NULL, agno, &agbp); if (error) @@ -497,28 +501,21 @@ del_cursor: */ irbufend = irbp; for (irbp = irbuf; - irbp < irbufend && XFS_BULKSTAT_UBLEFT(ubleft); irbp++) { - struct xfs_bulkstat_agichunk ac; - - ac.ac_lastino = lastino; - ac.ac_ubuffer = &ubuffer; - ac.ac_ubleft = ubleft; - ac.ac_ubelem = ubelem; + irbp < irbufend && XFS_BULKSTAT_UBLEFT(ac.ac_ubleft); + irbp++) { error = xfs_bulkstat_ag_ichunk(mp, agno, irbp, - formatter, statstruct_size, &ac); + formatter, statstruct_size, &ac, + &lastino); if (error) rval = error; - lastino = ac.ac_lastino; - ubleft = ac.ac_ubleft; - ubelem = ac.ac_ubelem; - cond_resched(); } + /* * Set up for the next loop iteration. */ - if (XFS_BULKSTAT_UBLEFT(ubleft)) { + if (XFS_BULKSTAT_UBLEFT(ac.ac_ubleft)) { if (end_of_ag) { agno++; agino = 0; @@ -531,11 +528,11 @@ del_cursor: * Done, we're either out of filesystem or space to put the data. */ kmem_free(irbuf); - *ubcountp = ubelem; + *ubcountp = ac.ac_ubelem; /* * Found some inodes, return them now and return the error next time. */ - if (ubelem) + if (ac.ac_ubelem) rval = 0; if (agno >= mp->m_sb.sb_agcount) { /* diff --git a/fs/xfs/xfs_itable.h b/fs/xfs/xfs_itable.h index aaed08022eb..6ea8b3912fa 100644 --- a/fs/xfs/xfs_itable.h +++ b/fs/xfs/xfs_itable.h @@ -30,22 +30,6 @@ typedef int (*bulkstat_one_pf)(struct xfs_mount *mp, int *ubused, int *stat); -struct xfs_bulkstat_agichunk { - xfs_ino_t ac_lastino; /* last inode returned */ - char __user **ac_ubuffer;/* pointer into user's buffer */ - int ac_ubleft; /* bytes left in user's buffer */ - int ac_ubelem; /* spaces used in user's buffer */ -}; - -int -xfs_bulkstat_ag_ichunk( - struct xfs_mount *mp, - xfs_agnumber_t agno, - struct xfs_inobt_rec_incore *irbp, - bulkstat_one_pf formatter, - size_t statstruct_size, - struct xfs_bulkstat_agichunk *acp); - /* * Values for stat return value. */ -- cgit v1.2.3-70-g09d2 From 2b831ac6bc87d3cbcbb1a8816827b6923403e461 Mon Sep 17 00:00:00 2001 From: Dave Chinner Date: Fri, 7 Nov 2014 08:30:58 +1100 Subject: xfs: bulkstat chunk-formatter has issues The loop construct has issues: - clustidx is completely unused, so remove it. - the loop tries to be smart by terminating when the "freecount" tells it that all inodes are free. Just drop it as in most cases we have to scan all inodes in the chunk anyway. - move the "user buffer left" condition check to the only point where we consume space int eh user buffer. - move the initialisation of agino out of the loop, leaving just a simple loop control logic using the clusteridx. Also, double handling of the user buffer variables leads to problems tracking the current state - use the cursor variables directly rather than keeping local copies and then having to update the cursor before returning. cc: # 3.17 Signed-off-by: Dave Chinner Reviewed-by: Brian Foster Signed-off-by: Dave Chinner --- fs/xfs/xfs_itable.c | 58 ++++++++++++++++++++++------------------------------- 1 file changed, 24 insertions(+), 34 deletions(-) diff --git a/fs/xfs/xfs_itable.c b/fs/xfs/xfs_itable.c index 50a3e5995dd..7ea2b113db1 100644 --- a/fs/xfs/xfs_itable.c +++ b/fs/xfs/xfs_itable.c @@ -283,59 +283,49 @@ xfs_bulkstat_ag_ichunk( xfs_ino_t *lastino) { char __user **ubufp = acp->ac_ubuffer; - int ubleft = acp->ac_ubleft; - int ubelem = acp->ac_ubelem; - int chunkidx, clustidx; + int chunkidx; int error = 0; xfs_agino_t agino; - for (agino = irbp->ir_startino, chunkidx = clustidx = 0; - XFS_BULKSTAT_UBLEFT(ubleft) && - irbp->ir_freecount < XFS_INODES_PER_CHUNK; - chunkidx++, clustidx++, agino++) { - int fmterror; /* bulkstat formatter result */ + agino = irbp->ir_startino; + for (chunkidx = 0; chunkidx < XFS_INODES_PER_CHUNK; + chunkidx++, agino++) { + int fmterror; int ubused; xfs_ino_t ino = XFS_AGINO_TO_INO(mp, agno, agino); - ASSERT(chunkidx < XFS_INODES_PER_CHUNK); - /* Skip if this inode is free */ if (XFS_INOBT_MASK(chunkidx) & irbp->ir_free) { *lastino = ino; continue; } - /* - * Count used inodes as free so we can tell when the - * chunk is used up. - */ - irbp->ir_freecount++; - /* Get the inode and fill in a single buffer */ ubused = statstruct_size; - error = formatter(mp, ino, *ubufp, ubleft, &ubused, &fmterror); - if (fmterror == BULKSTAT_RV_NOTHING) { - if (error && error != -ENOENT && error != -EINVAL) { - ubleft = 0; - break; - } - *lastino = ino; - continue; - } - if (fmterror == BULKSTAT_RV_GIVEUP) { - ubleft = 0; + error = formatter(mp, ino, *ubufp, acp->ac_ubleft, + &ubused, &fmterror); + if (fmterror == BULKSTAT_RV_GIVEUP || + (error && error != -ENOENT && error != -EINVAL)) { + acp->ac_ubleft = 0; ASSERT(error); break; } - if (*ubufp) - *ubufp += ubused; - ubleft -= ubused; - ubelem++; + + /* be careful not to leak error if at end of chunk */ + if (fmterror == BULKSTAT_RV_NOTHING || error) { + *lastino = ino; + error = 0; + continue; + } + + *ubufp += ubused; + acp->ac_ubleft -= ubused; + acp->ac_ubelem++; *lastino = ino; - } - acp->ac_ubleft = ubleft; - acp->ac_ubelem = ubelem; + if (acp->ac_ubleft < statstruct_size) + break; + } return error; } -- cgit v1.2.3-70-g09d2 From 6e57c542cb7e0e580eb53ae76a77875c7d92b4b1 Mon Sep 17 00:00:00 2001 From: Dave Chinner Date: Fri, 7 Nov 2014 08:31:13 +1100 Subject: xfs: bulkstat main loop logic is a mess There are a bunch of variables tha tare more wildy scoped than they need to be, obfuscated user buffer checks and tortured "next inode" tracking. This all needs cleaning up to expose the real issues that need fixing. cc: # 3.17 Signed-off-by: Dave Chinner Reviewed-by: Brian Foster Signed-off-by: Dave Chinner --- fs/xfs/xfs_itable.c | 56 +++++++++++++++++++++++------------------------------ 1 file changed, 24 insertions(+), 32 deletions(-) diff --git a/fs/xfs/xfs_itable.c b/fs/xfs/xfs_itable.c index 7ea2b113db1..acae3355ab2 100644 --- a/fs/xfs/xfs_itable.c +++ b/fs/xfs/xfs_itable.c @@ -348,30 +348,23 @@ xfs_bulkstat( xfs_agino_t agino; /* inode # in allocation group */ xfs_agnumber_t agno; /* allocation group number */ xfs_btree_cur_t *cur; /* btree cursor for ialloc btree */ - int end_of_ag; /* set if we've seen the ag end */ - int error; /* error code */ - int icount; /* count of inodes good in irbuf */ size_t irbsize; /* size of irec buffer in bytes */ - xfs_ino_t ino; /* inode number (filesystem) */ - xfs_inobt_rec_incore_t *irbp; /* current irec buffer pointer */ xfs_inobt_rec_incore_t *irbuf; /* start of irec buffer */ - xfs_inobt_rec_incore_t *irbufend; /* end of good irec buffer entries */ xfs_ino_t lastino; /* last inode number returned */ int nirbuf; /* size of irbuf */ int rval; /* return value error code */ int ubcount; /* size of user's buffer */ - int stat; struct xfs_bulkstat_agichunk ac; + int error = 0; /* * Get the last inode value, see if there's nothing to do. */ - ino = (xfs_ino_t)*lastinop; - lastino = ino; - agno = XFS_INO_TO_AGNO(mp, ino); - agino = XFS_INO_TO_AGINO(mp, ino); + lastino = *lastinop; + agno = XFS_INO_TO_AGNO(mp, lastino); + agino = XFS_INO_TO_AGINO(mp, lastino); if (agno >= mp->m_sb.sb_agcount || - ino != XFS_AGINO_TO_INO(mp, agno, agino)) { + lastino != XFS_AGINO_TO_INO(mp, agno, agino)) { *done = 1; *ubcountp = 0; return 0; @@ -396,8 +389,13 @@ xfs_bulkstat( * inode returned; 0 means start of the allocation group. */ rval = 0; - while (XFS_BULKSTAT_UBLEFT(ac.ac_ubleft) && agno < mp->m_sb.sb_agcount) { - cond_resched(); + while (agno < mp->m_sb.sb_agcount) { + struct xfs_inobt_rec_incore *irbp = irbuf; + struct xfs_inobt_rec_incore *irbufend = irbuf + nirbuf; + bool end_of_ag = false; + int icount = 0; + int stat; + error = xfs_ialloc_read_agi(mp, NULL, agno, &agbp); if (error) break; @@ -407,10 +405,6 @@ xfs_bulkstat( */ cur = xfs_inobt_init_cursor(mp, NULL, agbp, agno, XFS_BTNUM_INO); - irbp = irbuf; - irbufend = irbuf + nirbuf; - end_of_ag = 0; - icount = 0; if (agino > 0) { /* * In the middle of an allocation group, we need to get @@ -435,7 +429,7 @@ xfs_bulkstat( error = xfs_inobt_lookup(cur, 0, XFS_LOOKUP_GE, &stat); } if (error || stat == 0) { - end_of_ag = 1; + end_of_ag = true; goto del_cursor; } @@ -448,7 +442,7 @@ xfs_bulkstat( error = xfs_inobt_get_rec(cur, &r, &stat); if (error || stat == 0) { - end_of_ag = 1; + end_of_ag = true; goto del_cursor; } @@ -470,7 +464,7 @@ xfs_bulkstat( agino = r.ir_startino + XFS_INODES_PER_CHUNK; error = xfs_btree_increment(cur, 0, &stat); if (error || stat == 0) { - end_of_ag = 1; + end_of_ag = true; goto del_cursor; } cond_resched(); @@ -491,7 +485,7 @@ del_cursor: */ irbufend = irbp; for (irbp = irbuf; - irbp < irbufend && XFS_BULKSTAT_UBLEFT(ac.ac_ubleft); + irbp < irbufend && ac.ac_ubleft >= statstruct_size; irbp++) { error = xfs_bulkstat_ag_ichunk(mp, agno, irbp, formatter, statstruct_size, &ac, @@ -502,17 +496,15 @@ del_cursor: cond_resched(); } - /* - * Set up for the next loop iteration. - */ - if (XFS_BULKSTAT_UBLEFT(ac.ac_ubleft)) { - if (end_of_ag) { - agno++; - agino = 0; - } else - agino = XFS_INO_TO_AGINO(mp, lastino); - } else + /* If we've run out of space, we are done */ + if (ac.ac_ubleft < statstruct_size) break; + + if (end_of_ag) { + agno++; + agino = 0; + } else + agino = XFS_INO_TO_AGINO(mp, lastino); } /* * Done, we're either out of filesystem or space to put the data. -- cgit v1.2.3-70-g09d2 From febe3cbe38b0bc0a925906dc90e8d59048851f87 Mon Sep 17 00:00:00 2001 From: Dave Chinner Date: Fri, 7 Nov 2014 08:31:15 +1100 Subject: xfs: bulkstat error handling is broken The error propagation is a horror - xfs_bulkstat() returns a rval variable which is only set if there are formatter errors. Any sort of btree walk error or corruption will cause the bulkstat walk to terminate but will not pass an error back to userspace. Worse is the fact that formatter errors will also be ignored if any inodes were correctly formatted into the user buffer. Hence bulkstat can fail badly yet still report success to userspace. This causes significant issues with xfsdump not dumping everything in the filesystem yet reporting success. It's not until a restore fails that there is any indication that the dump was bad and tha bulkstat failed. This patch now triggers xfsdump to fail with bulkstat errors rather than silently missing files in the dump. This now causes bulkstat to fail when the lastino cookie does not fall inside an existing inode chunk. The pre-3.17 code tolerated that error by allowing the code to move to the next inode chunk as the agino target is guaranteed to fall into the next btree record. With the fixes up to this point in the series, xfsdump now passes on the troublesome filesystem image that exposes all these bugs. cc: Signed-off-by: Dave Chinner Reviewed-by: Brian Foster --- fs/xfs/xfs_itable.c | 29 +++++++++++++++++++---------- 1 file changed, 19 insertions(+), 10 deletions(-) diff --git a/fs/xfs/xfs_itable.c b/fs/xfs/xfs_itable.c index acae3355ab2..ff3f431671b 100644 --- a/fs/xfs/xfs_itable.c +++ b/fs/xfs/xfs_itable.c @@ -236,8 +236,10 @@ xfs_bulkstat_grab_ichunk( XFS_WANT_CORRUPTED_RETURN(stat == 1); /* Check if the record contains the inode in request */ - if (irec->ir_startino + XFS_INODES_PER_CHUNK <= agino) - return -EINVAL; + if (irec->ir_startino + XFS_INODES_PER_CHUNK <= agino) { + *icount = 0; + return 0; + } idx = agino - irec->ir_startino + 1; if (idx < XFS_INODES_PER_CHUNK && @@ -352,7 +354,6 @@ xfs_bulkstat( xfs_inobt_rec_incore_t *irbuf; /* start of irec buffer */ xfs_ino_t lastino; /* last inode number returned */ int nirbuf; /* size of irbuf */ - int rval; /* return value error code */ int ubcount; /* size of user's buffer */ struct xfs_bulkstat_agichunk ac; int error = 0; @@ -388,7 +389,6 @@ xfs_bulkstat( * Loop over the allocation groups, starting from the last * inode returned; 0 means start of the allocation group. */ - rval = 0; while (agno < mp->m_sb.sb_agcount) { struct xfs_inobt_rec_incore *irbp = irbuf; struct xfs_inobt_rec_incore *irbufend = irbuf + nirbuf; @@ -491,13 +491,16 @@ del_cursor: formatter, statstruct_size, &ac, &lastino); if (error) - rval = error; + break; cond_resched(); } - /* If we've run out of space, we are done */ - if (ac.ac_ubleft < statstruct_size) + /* + * If we've run out of space or had a formatting error, we + * are now done + */ + if (ac.ac_ubleft < statstruct_size || error) break; if (end_of_ag) { @@ -511,11 +514,17 @@ del_cursor: */ kmem_free(irbuf); *ubcountp = ac.ac_ubelem; + /* - * Found some inodes, return them now and return the error next time. + * We found some inodes, so clear the error status and return them. + * The lastino pointer will point directly at the inode that triggered + * any error that occurred, so on the next call the error will be + * triggered again and propagated to userspace as there will be no + * formatted inodes in the buffer. */ if (ac.ac_ubelem) - rval = 0; + error = 0; + if (agno >= mp->m_sb.sb_agcount) { /* * If we ran out of filesystem, mark lastino as off @@ -527,7 +536,7 @@ del_cursor: } else *lastinop = (xfs_ino_t)lastino; - return rval; + return error; } int -- cgit v1.2.3-70-g09d2 From 002758992693ae63c04122603ea9261a0a58d728 Mon Sep 17 00:00:00 2001 From: Dave Chinner Date: Fri, 7 Nov 2014 08:33:52 +1100 Subject: xfs: track bulkstat progress by agino The bulkstat main loop progress is tracked by the "lastino" variable, which is a full 64 bit inode. However, the loop actually works on agno/agino pairs, and so there's a significant disconnect between the rest of the loop and the main cursor. Convert this to use the agino, and pass the agino into the chunk formatting function and convert it too. This gets rid of the inconsistency in the loop processing, and finally makes it simple for us to skip inodes at any point in the loop simply by incrementing the agino cursor. cc: # 3.17 Signed-off-by: Dave Chinner Reviewed-by: Brian Foster Signed-off-by: Dave Chinner --- fs/xfs/xfs_itable.c | 71 +++++++++++++++++++++++++---------------------------- 1 file changed, 34 insertions(+), 37 deletions(-) diff --git a/fs/xfs/xfs_itable.c b/fs/xfs/xfs_itable.c index ff3f431671b..894924a5129 100644 --- a/fs/xfs/xfs_itable.c +++ b/fs/xfs/xfs_itable.c @@ -282,30 +282,31 @@ xfs_bulkstat_ag_ichunk( bulkstat_one_pf formatter, size_t statstruct_size, struct xfs_bulkstat_agichunk *acp, - xfs_ino_t *lastino) + xfs_agino_t *last_agino) { char __user **ubufp = acp->ac_ubuffer; int chunkidx; int error = 0; - xfs_agino_t agino; + xfs_agino_t agino = irbp->ir_startino; - agino = irbp->ir_startino; for (chunkidx = 0; chunkidx < XFS_INODES_PER_CHUNK; chunkidx++, agino++) { int fmterror; int ubused; - xfs_ino_t ino = XFS_AGINO_TO_INO(mp, agno, agino); + + /* inode won't fit in buffer, we are done */ + if (acp->ac_ubleft < statstruct_size) + break; /* Skip if this inode is free */ - if (XFS_INOBT_MASK(chunkidx) & irbp->ir_free) { - *lastino = ino; + if (XFS_INOBT_MASK(chunkidx) & irbp->ir_free) continue; - } /* Get the inode and fill in a single buffer */ ubused = statstruct_size; - error = formatter(mp, ino, *ubufp, acp->ac_ubleft, - &ubused, &fmterror); + error = formatter(mp, XFS_AGINO_TO_INO(mp, agno, agino), + *ubufp, acp->ac_ubleft, &ubused, &fmterror); + if (fmterror == BULKSTAT_RV_GIVEUP || (error && error != -ENOENT && error != -EINVAL)) { acp->ac_ubleft = 0; @@ -315,7 +316,6 @@ xfs_bulkstat_ag_ichunk( /* be careful not to leak error if at end of chunk */ if (fmterror == BULKSTAT_RV_NOTHING || error) { - *lastino = ino; error = 0; continue; } @@ -323,12 +323,18 @@ xfs_bulkstat_ag_ichunk( *ubufp += ubused; acp->ac_ubleft -= ubused; acp->ac_ubelem++; - *lastino = ino; - - if (acp->ac_ubleft < statstruct_size) - break; } + /* + * Post-update *last_agino. At this point, agino will always point one + * inode past the last inode we processed successfully. Hence we + * substract that inode when setting the *last_agino cursor so that we + * return the correct cookie to userspace. On the next bulkstat call, + * the inode under the lastino cookie will be skipped as we have already + * processed it here. + */ + *last_agino = agino - 1; + return error; } @@ -352,7 +358,6 @@ xfs_bulkstat( xfs_btree_cur_t *cur; /* btree cursor for ialloc btree */ size_t irbsize; /* size of irec buffer in bytes */ xfs_inobt_rec_incore_t *irbuf; /* start of irec buffer */ - xfs_ino_t lastino; /* last inode number returned */ int nirbuf; /* size of irbuf */ int ubcount; /* size of user's buffer */ struct xfs_bulkstat_agichunk ac; @@ -361,11 +366,10 @@ xfs_bulkstat( /* * Get the last inode value, see if there's nothing to do. */ - lastino = *lastinop; - agno = XFS_INO_TO_AGNO(mp, lastino); - agino = XFS_INO_TO_AGINO(mp, lastino); + agno = XFS_INO_TO_AGNO(mp, *lastinop); + agino = XFS_INO_TO_AGINO(mp, *lastinop); if (agno >= mp->m_sb.sb_agcount || - lastino != XFS_AGINO_TO_INO(mp, agno, agino)) { + *lastinop != XFS_AGINO_TO_INO(mp, agno, agino)) { *done = 1; *ubcountp = 0; return 0; @@ -420,7 +424,6 @@ xfs_bulkstat( irbp->ir_freecount = r.ir_freecount; irbp->ir_free = r.ir_free; irbp++; - agino = r.ir_startino + XFS_INODES_PER_CHUNK; } /* Increment to the next record */ error = xfs_btree_increment(cur, 0, &stat); @@ -458,10 +461,6 @@ xfs_bulkstat( irbp++; icount += XFS_INODES_PER_CHUNK - r.ir_freecount; } - /* - * Set agino to after this chunk and bump the cursor. - */ - agino = r.ir_startino + XFS_INODES_PER_CHUNK; error = xfs_btree_increment(cur, 0, &stat); if (error || stat == 0) { end_of_ag = true; @@ -481,7 +480,9 @@ del_cursor: if (error) break; /* - * Now format all the good inodes into the user's buffer. + * Now format all the good inodes into the user's buffer. The + * call to xfs_bulkstat_ag_ichunk() sets up the agino pointer + * for the next loop iteration. */ irbufend = irbp; for (irbp = irbuf; @@ -489,7 +490,7 @@ del_cursor: irbp++) { error = xfs_bulkstat_ag_ichunk(mp, agno, irbp, formatter, statstruct_size, &ac, - &lastino); + &agino); if (error) break; @@ -506,8 +507,7 @@ del_cursor: if (end_of_ag) { agno++; agino = 0; - } else - agino = XFS_INO_TO_AGINO(mp, lastino); + } } /* * Done, we're either out of filesystem or space to put the data. @@ -525,16 +525,13 @@ del_cursor: if (ac.ac_ubelem) error = 0; - if (agno >= mp->m_sb.sb_agcount) { - /* - * If we ran out of filesystem, mark lastino as off - * the end of the filesystem, so the next call - * will return immediately. - */ - *lastinop = (xfs_ino_t)XFS_AGINO_TO_INO(mp, agno, 0); + /* + * If we ran out of filesystem, lastino will point off the end of + * the filesystem so the next call will return immediately. + */ + *lastinop = XFS_AGINO_TO_INO(mp, agno, agino); + if (agno >= mp->m_sb.sb_agcount) *done = 1; - } else - *lastinop = (xfs_ino_t)lastino; return error; } -- cgit v1.2.3-70-g09d2 From 842dfc11ea9a21f9825167c8a4f2834b205b0a79 Mon Sep 17 00:00:00 2001 From: Manuel Lauss Date: Fri, 7 Nov 2014 14:13:54 +0100 Subject: MIPS: Fix build with binutils 2.24.51+ Starting with version 2.24.51.20140728 MIPS binutils complain loudly about mixing soft-float and hard-float object files, leading to this build failure since GCC is invoked with "-msoft-float" on MIPS: {standard input}: Warning: .gnu_attribute 4,3 requires `softfloat' LD arch/mips/alchemy/common/built-in.o mipsel-softfloat-linux-gnu-ld: Warning: arch/mips/alchemy/common/built-in.o uses -msoft-float (set by arch/mips/alchemy/common/prom.o), arch/mips/alchemy/common/sleeper.o uses -mhard-float To fix this, we detect if GAS is new enough to support "-msoft-float" command option, and if it does, we can let GCC pass it to GAS; but then we also need to sprinkle the files which make use of floating point registers with the necessary ".set hardfloat" directives. Signed-off-by: Manuel Lauss Cc: Linux-MIPS Cc: Matthew Fortune Cc: Markos Chandras Cc: Maciej W. Rozycki Patchwork: https://patchwork.linux-mips.org/patch/8355/ Signed-off-by: Ralf Baechle --- arch/mips/Makefile | 9 +++++++++ arch/mips/include/asm/asmmacro-32.h | 6 ++++++ arch/mips/include/asm/asmmacro.h | 18 ++++++++++++++++++ arch/mips/include/asm/fpregdef.h | 14 ++++++++++++++ arch/mips/include/asm/fpu.h | 4 ++-- arch/mips/include/asm/mipsregs.h | 11 ++++++++++- arch/mips/kernel/branch.c | 8 ++------ arch/mips/kernel/genex.S | 1 + arch/mips/kernel/r2300_fpu.S | 6 ++++++ arch/mips/kernel/r2300_switch.S | 5 +++++ arch/mips/kernel/r4k_fpu.S | 27 +++++++++++++++++++++++++-- arch/mips/kernel/r4k_switch.S | 15 ++++++++++++++- arch/mips/kernel/r6000_fpu.S | 5 +++++ arch/mips/math-emu/cp1emu.c | 6 +----- 14 files changed, 118 insertions(+), 17 deletions(-) diff --git a/arch/mips/Makefile b/arch/mips/Makefile index 23cb94806fb..58076472bdd 100644 --- a/arch/mips/Makefile +++ b/arch/mips/Makefile @@ -93,6 +93,15 @@ LDFLAGS_vmlinux += -G 0 -static -n -nostdlib KBUILD_AFLAGS_MODULE += -mlong-calls KBUILD_CFLAGS_MODULE += -mlong-calls +# +# pass -msoft-float to GAS if it supports it. However on newer binutils +# (specifically newer than 2.24.51.20140728) we then also need to explicitly +# set ".set hardfloat" in all files which manipulate floating point registers. +# +ifneq ($(call as-option,-Wa$(comma)-msoft-float,),) + cflags-y += -DGAS_HAS_SET_HARDFLOAT -Wa,-msoft-float +endif + cflags-y += -ffreestanding # diff --git a/arch/mips/include/asm/asmmacro-32.h b/arch/mips/include/asm/asmmacro-32.h index e38c2811d4e..cdac7b3eeaf 100644 --- a/arch/mips/include/asm/asmmacro-32.h +++ b/arch/mips/include/asm/asmmacro-32.h @@ -13,6 +13,8 @@ #include .macro fpu_save_single thread tmp=t0 + .set push + SET_HARDFLOAT cfc1 \tmp, fcr31 swc1 $f0, THREAD_FPR0_LS64(\thread) swc1 $f1, THREAD_FPR1_LS64(\thread) @@ -47,9 +49,12 @@ swc1 $f30, THREAD_FPR30_LS64(\thread) swc1 $f31, THREAD_FPR31_LS64(\thread) sw \tmp, THREAD_FCR31(\thread) + .set pop .endm .macro fpu_restore_single thread tmp=t0 + .set push + SET_HARDFLOAT lw \tmp, THREAD_FCR31(\thread) lwc1 $f0, THREAD_FPR0_LS64(\thread) lwc1 $f1, THREAD_FPR1_LS64(\thread) @@ -84,6 +89,7 @@ lwc1 $f30, THREAD_FPR30_LS64(\thread) lwc1 $f31, THREAD_FPR31_LS64(\thread) ctc1 \tmp, fcr31 + .set pop .endm .macro cpu_save_nonscratch thread diff --git a/arch/mips/include/asm/asmmacro.h b/arch/mips/include/asm/asmmacro.h index cd9a98bc8f6..6caf8766b80 100644 --- a/arch/mips/include/asm/asmmacro.h +++ b/arch/mips/include/asm/asmmacro.h @@ -57,6 +57,8 @@ #endif /* CONFIG_CPU_MIPSR2 */ .macro fpu_save_16even thread tmp=t0 + .set push + SET_HARDFLOAT cfc1 \tmp, fcr31 sdc1 $f0, THREAD_FPR0_LS64(\thread) sdc1 $f2, THREAD_FPR2_LS64(\thread) @@ -75,11 +77,13 @@ sdc1 $f28, THREAD_FPR28_LS64(\thread) sdc1 $f30, THREAD_FPR30_LS64(\thread) sw \tmp, THREAD_FCR31(\thread) + .set pop .endm .macro fpu_save_16odd thread .set push .set mips64r2 + SET_HARDFLOAT sdc1 $f1, THREAD_FPR1_LS64(\thread) sdc1 $f3, THREAD_FPR3_LS64(\thread) sdc1 $f5, THREAD_FPR5_LS64(\thread) @@ -110,6 +114,8 @@ .endm .macro fpu_restore_16even thread tmp=t0 + .set push + SET_HARDFLOAT lw \tmp, THREAD_FCR31(\thread) ldc1 $f0, THREAD_FPR0_LS64(\thread) ldc1 $f2, THREAD_FPR2_LS64(\thread) @@ -133,6 +139,7 @@ .macro fpu_restore_16odd thread .set push .set mips64r2 + SET_HARDFLOAT ldc1 $f1, THREAD_FPR1_LS64(\thread) ldc1 $f3, THREAD_FPR3_LS64(\thread) ldc1 $f5, THREAD_FPR5_LS64(\thread) @@ -277,6 +284,7 @@ .macro cfcmsa rd, cs .set push .set noat + SET_HARDFLOAT .insn .word CFC_MSA_INSN | (\cs << 11) move \rd, $1 @@ -286,6 +294,7 @@ .macro ctcmsa cd, rs .set push .set noat + SET_HARDFLOAT move $1, \rs .word CTC_MSA_INSN | (\cd << 6) .set pop @@ -294,6 +303,7 @@ .macro ld_d wd, off, base .set push .set noat + SET_HARDFLOAT add $1, \base, \off .word LDD_MSA_INSN | (\wd << 6) .set pop @@ -302,6 +312,7 @@ .macro st_d wd, off, base .set push .set noat + SET_HARDFLOAT add $1, \base, \off .word STD_MSA_INSN | (\wd << 6) .set pop @@ -310,6 +321,7 @@ .macro copy_u_w rd, ws, n .set push .set noat + SET_HARDFLOAT .insn .word COPY_UW_MSA_INSN | (\n << 16) | (\ws << 11) /* move triggers an assembler bug... */ @@ -320,6 +332,7 @@ .macro copy_u_d rd, ws, n .set push .set noat + SET_HARDFLOAT .insn .word COPY_UD_MSA_INSN | (\n << 16) | (\ws << 11) /* move triggers an assembler bug... */ @@ -330,6 +343,7 @@ .macro insert_w wd, n, rs .set push .set noat + SET_HARDFLOAT /* move triggers an assembler bug... */ or $1, \rs, zero .word INSERT_W_MSA_INSN | (\n << 16) | (\wd << 6) @@ -339,6 +353,7 @@ .macro insert_d wd, n, rs .set push .set noat + SET_HARDFLOAT /* move triggers an assembler bug... */ or $1, \rs, zero .word INSERT_D_MSA_INSN | (\n << 16) | (\wd << 6) @@ -381,6 +396,7 @@ st_d 31, THREAD_FPR31, \thread .set push .set noat + SET_HARDFLOAT cfcmsa $1, MSA_CSR sw $1, THREAD_MSA_CSR(\thread) .set pop @@ -389,6 +405,7 @@ .macro msa_restore_all thread .set push .set noat + SET_HARDFLOAT lw $1, THREAD_MSA_CSR(\thread) ctcmsa MSA_CSR, $1 .set pop @@ -441,6 +458,7 @@ .macro msa_init_all_upper .set push .set noat + SET_HARDFLOAT not $1, zero msa_init_upper 0 .set pop diff --git a/arch/mips/include/asm/fpregdef.h b/arch/mips/include/asm/fpregdef.h index 429481f9028..f184ba08853 100644 --- a/arch/mips/include/asm/fpregdef.h +++ b/arch/mips/include/asm/fpregdef.h @@ -14,6 +14,20 @@ #include +/* + * starting with binutils 2.24.51.20140729, MIPS binutils warn about mixing + * hardfloat and softfloat object files. The kernel build uses soft-float by + * default, so we also need to pass -msoft-float along to GAS if it supports it. + * But this in turn causes assembler errors in files which access hardfloat + * registers. We detect if GAS supports "-msoft-float" in the Makefile and + * explicitly put ".set hardfloat" where floating point registers are touched. + */ +#ifdef GAS_HAS_SET_HARDFLOAT +#define SET_HARDFLOAT .set hardfloat +#else +#define SET_HARDFLOAT +#endif + #if _MIPS_SIM == _MIPS_SIM_ABI32 /* diff --git a/arch/mips/include/asm/fpu.h b/arch/mips/include/asm/fpu.h index 4d0aeda6839..dd562414cd5 100644 --- a/arch/mips/include/asm/fpu.h +++ b/arch/mips/include/asm/fpu.h @@ -145,8 +145,8 @@ static inline void lose_fpu(int save) if (is_msa_enabled()) { if (save) { save_msa(current); - asm volatile("cfc1 %0, $31" - : "=r"(current->thread.fpu.fcr31)); + current->thread.fpu.fcr31 = + read_32bit_cp1_register(CP1_STATUS); } disable_msa(); clear_thread_flag(TIF_USEDMSA); diff --git a/arch/mips/include/asm/mipsregs.h b/arch/mips/include/asm/mipsregs.h index cf3b580c3df..b46cd220a01 100644 --- a/arch/mips/include/asm/mipsregs.h +++ b/arch/mips/include/asm/mipsregs.h @@ -1324,7 +1324,7 @@ do { \ /* * Macros to access the floating point coprocessor control registers */ -#define read_32bit_cp1_register(source) \ +#define _read_32bit_cp1_register(source, gas_hardfloat) \ ({ \ int __res; \ \ @@ -1334,12 +1334,21 @@ do { \ " # gas fails to assemble cfc1 for some archs, \n" \ " # like Octeon. \n" \ " .set mips1 \n" \ + " "STR(gas_hardfloat)" \n" \ " cfc1 %0,"STR(source)" \n" \ " .set pop \n" \ : "=r" (__res)); \ __res; \ }) +#ifdef GAS_HAS_SET_HARDFLOAT +#define read_32bit_cp1_register(source) \ + _read_32bit_cp1_register(source, .set hardfloat) +#else +#define read_32bit_cp1_register(source) \ + _read_32bit_cp1_register(source, ) +#endif + #ifdef HAVE_AS_DSP #define rddsp(mask) \ ({ \ diff --git a/arch/mips/kernel/branch.c b/arch/mips/kernel/branch.c index 7b2df224f04..4d7d99d601c 100644 --- a/arch/mips/kernel/branch.c +++ b/arch/mips/kernel/branch.c @@ -144,7 +144,7 @@ int __mm_isBranchInstr(struct pt_regs *regs, struct mm_decoded_insn dec_insn, case mm_bc1t_op: preempt_disable(); if (is_fpu_owner()) - asm volatile("cfc1\t%0,$31" : "=r" (fcr31)); + fcr31 = read_32bit_cp1_register(CP1_STATUS); else fcr31 = current->thread.fpu.fcr31; preempt_enable(); @@ -562,11 +562,7 @@ int __compute_return_epc_for_insn(struct pt_regs *regs, case cop1_op: preempt_disable(); if (is_fpu_owner()) - asm volatile( - ".set push\n" - "\t.set mips1\n" - "\tcfc1\t%0,$31\n" - "\t.set pop" : "=r" (fcr31)); + fcr31 = read_32bit_cp1_register(CP1_STATUS); else fcr31 = current->thread.fpu.fcr31; preempt_enable(); diff --git a/arch/mips/kernel/genex.S b/arch/mips/kernel/genex.S index ac35e12cb1f..a5e26dd9059 100644 --- a/arch/mips/kernel/genex.S +++ b/arch/mips/kernel/genex.S @@ -358,6 +358,7 @@ NESTED(nmi_handler, PT_SIZE, sp) .set push /* gas fails to assemble cfc1 for some archs (octeon).*/ \ .set mips1 + SET_HARDFLOAT cfc1 a1, fcr31 li a2, ~(0x3f << 12) and a2, a1 diff --git a/arch/mips/kernel/r2300_fpu.S b/arch/mips/kernel/r2300_fpu.S index f31063dbdae..5ce3b746ced 100644 --- a/arch/mips/kernel/r2300_fpu.S +++ b/arch/mips/kernel/r2300_fpu.S @@ -28,6 +28,8 @@ .set mips1 /* Save floating point context */ LEAF(_save_fp_context) + .set push + SET_HARDFLOAT li v0, 0 # assume success cfc1 t1,fcr31 EX(swc1 $f0,(SC_FPREGS+0)(a0)) @@ -65,6 +67,7 @@ LEAF(_save_fp_context) EX(sw t1,(SC_FPC_CSR)(a0)) cfc1 t0,$0 # implementation/version jr ra + .set pop .set nomacro EX(sw t0,(SC_FPC_EIR)(a0)) .set macro @@ -80,6 +83,8 @@ LEAF(_save_fp_context) * stack frame which might have been changed by the user. */ LEAF(_restore_fp_context) + .set push + SET_HARDFLOAT li v0, 0 # assume success EX(lw t0,(SC_FPC_CSR)(a0)) EX(lwc1 $f0,(SC_FPREGS+0)(a0)) @@ -116,6 +121,7 @@ LEAF(_restore_fp_context) EX(lwc1 $f31,(SC_FPREGS+248)(a0)) jr ra ctc1 t0,fcr31 + .set pop END(_restore_fp_context) .set reorder diff --git a/arch/mips/kernel/r2300_switch.S b/arch/mips/kernel/r2300_switch.S index 20b7b040e76..435ea652f5f 100644 --- a/arch/mips/kernel/r2300_switch.S +++ b/arch/mips/kernel/r2300_switch.S @@ -120,6 +120,9 @@ LEAF(_restore_fp) #define FPU_DEFAULT 0x00000000 + .set push + SET_HARDFLOAT + LEAF(_init_fpu) mfc0 t0, CP0_STATUS li t1, ST0_CU1 @@ -165,3 +168,5 @@ LEAF(_init_fpu) mtc1 t0, $f31 jr ra END(_init_fpu) + + .set pop diff --git a/arch/mips/kernel/r4k_fpu.S b/arch/mips/kernel/r4k_fpu.S index 8352523568e..6c160c67984 100644 --- a/arch/mips/kernel/r4k_fpu.S +++ b/arch/mips/kernel/r4k_fpu.S @@ -19,8 +19,12 @@ #include #include +/* preprocessor replaces the fp in ".set fp=64" with $30 otherwise */ +#undef fp + .macro EX insn, reg, src .set push + SET_HARDFLOAT .set nomacro .ex\@: \insn \reg, \src .set pop @@ -33,12 +37,17 @@ .set arch=r4000 LEAF(_save_fp_context) + .set push + SET_HARDFLOAT cfc1 t1, fcr31 + .set pop #if defined(CONFIG_64BIT) || defined(CONFIG_CPU_MIPS32_R2) .set push + SET_HARDFLOAT #ifdef CONFIG_CPU_MIPS32_R2 - .set mips64r2 + .set mips32r2 + .set fp=64 mfc0 t0, CP0_STATUS sll t0, t0, 5 bgez t0, 1f # skip storing odd if FR=0 @@ -64,6 +73,8 @@ LEAF(_save_fp_context) 1: .set pop #endif + .set push + SET_HARDFLOAT /* Store the 16 even double precision registers */ EX sdc1 $f0, SC_FPREGS+0(a0) EX sdc1 $f2, SC_FPREGS+16(a0) @@ -84,11 +95,14 @@ LEAF(_save_fp_context) EX sw t1, SC_FPC_CSR(a0) jr ra li v0, 0 # success + .set pop END(_save_fp_context) #ifdef CONFIG_MIPS32_COMPAT /* Save 32-bit process floating point context */ LEAF(_save_fp_context32) + .set push + SET_HARDFLOAT cfc1 t1, fcr31 mfc0 t0, CP0_STATUS @@ -134,6 +148,7 @@ LEAF(_save_fp_context32) EX sw t1, SC32_FPC_CSR(a0) cfc1 t0, $0 # implementation/version EX sw t0, SC32_FPC_EIR(a0) + .set pop jr ra li v0, 0 # success @@ -150,8 +165,10 @@ LEAF(_restore_fp_context) #if defined(CONFIG_64BIT) || defined(CONFIG_CPU_MIPS32_R2) .set push + SET_HARDFLOAT #ifdef CONFIG_CPU_MIPS32_R2 - .set mips64r2 + .set mips32r2 + .set fp=64 mfc0 t0, CP0_STATUS sll t0, t0, 5 bgez t0, 1f # skip loading odd if FR=0 @@ -175,6 +192,8 @@ LEAF(_restore_fp_context) EX ldc1 $f31, SC_FPREGS+248(a0) 1: .set pop #endif + .set push + SET_HARDFLOAT EX ldc1 $f0, SC_FPREGS+0(a0) EX ldc1 $f2, SC_FPREGS+16(a0) EX ldc1 $f4, SC_FPREGS+32(a0) @@ -192,6 +211,7 @@ LEAF(_restore_fp_context) EX ldc1 $f28, SC_FPREGS+224(a0) EX ldc1 $f30, SC_FPREGS+240(a0) ctc1 t1, fcr31 + .set pop jr ra li v0, 0 # success END(_restore_fp_context) @@ -199,6 +219,8 @@ LEAF(_restore_fp_context) #ifdef CONFIG_MIPS32_COMPAT LEAF(_restore_fp_context32) /* Restore an o32 sigcontext. */ + .set push + SET_HARDFLOAT EX lw t1, SC32_FPC_CSR(a0) mfc0 t0, CP0_STATUS @@ -242,6 +264,7 @@ LEAF(_restore_fp_context32) ctc1 t1, fcr31 jr ra li v0, 0 # success + .set pop END(_restore_fp_context32) #endif diff --git a/arch/mips/kernel/r4k_switch.S b/arch/mips/kernel/r4k_switch.S index 4c4ec181242..64591e67187 100644 --- a/arch/mips/kernel/r4k_switch.S +++ b/arch/mips/kernel/r4k_switch.S @@ -22,6 +22,9 @@ #include +/* preprocessor replaces the fp in ".set fp=64" with $30 otherwise */ +#undef fp + /* * Offset to the current process status flags, the first 32 bytes of the * stack are not used. @@ -65,8 +68,12 @@ bgtz a3, 1f /* Save 128b MSA vector context + scalar FP control & status. */ + .set push + SET_HARDFLOAT cfc1 t1, fcr31 msa_save_all a0 + .set pop /* SET_HARDFLOAT */ + sw t1, THREAD_FCR31(a0) b 2f @@ -161,6 +168,9 @@ LEAF(_init_msa_upper) #define FPU_DEFAULT 0x00000000 + .set push + SET_HARDFLOAT + LEAF(_init_fpu) mfc0 t0, CP0_STATUS li t1, ST0_CU1 @@ -232,7 +242,8 @@ LEAF(_init_fpu) #ifdef CONFIG_CPU_MIPS32_R2 .set push - .set mips64r2 + .set mips32r2 + .set fp=64 sll t0, t0, 5 # is Status.FR set? bgez t0, 1f # no: skip setting upper 32b @@ -291,3 +302,5 @@ LEAF(_init_fpu) #endif jr ra END(_init_fpu) + + .set pop /* SET_HARDFLOAT */ diff --git a/arch/mips/kernel/r6000_fpu.S b/arch/mips/kernel/r6000_fpu.S index da0fbe46d83..47077380c15 100644 --- a/arch/mips/kernel/r6000_fpu.S +++ b/arch/mips/kernel/r6000_fpu.S @@ -18,6 +18,9 @@ .set noreorder .set mips2 + .set push + SET_HARDFLOAT + /* Save floating point context */ LEAF(_save_fp_context) mfc0 t0,CP0_STATUS @@ -85,3 +88,5 @@ 1: jr ra nop END(_restore_fp_context) + + .set pop /* SET_HARDFLOAT */ diff --git a/arch/mips/math-emu/cp1emu.c b/arch/mips/math-emu/cp1emu.c index 51a0fde4bec..cac529a405b 100644 --- a/arch/mips/math-emu/cp1emu.c +++ b/arch/mips/math-emu/cp1emu.c @@ -584,11 +584,7 @@ static int isBranchInstr(struct pt_regs *regs, struct mm_decoded_insn dec_insn, if (insn.i_format.rs == bc_op) { preempt_disable(); if (is_fpu_owner()) - asm volatile( - ".set push\n" - "\t.set mips1\n" - "\tcfc1\t%0,$31\n" - "\t.set pop" : "=r" (fcr31)); + fcr31 = read_32bit_cp1_register(CP1_STATUS); else fcr31 = current->thread.fpu.fcr31; preempt_enable(); -- cgit v1.2.3-70-g09d2 From e4a60d139060975eb956717e4f63ae348d4d8cc5 Mon Sep 17 00:00:00 2001 From: Yijing Wang Date: Fri, 7 Nov 2014 12:05:49 +0800 Subject: sysfs: driver core: Fix glue dir race condition by gdp_mutex There is a race condition when removing glue directory. It can be reproduced in following test: path 1: Add first child device device_add() get_device_parent() /*find parent from glue_dirs.list*/ list_for_each_entry(k, &dev->class->p->glue_dirs.list, entry) if (k->parent == parent_kobj) { kobj = kobject_get(k); break; } .... class_dir_create_and_add() path2: Remove last child device under glue dir device_del() cleanup_device_parent() cleanup_glue_dir() kobject_put(glue_dir); If path2 has been called cleanup_glue_dir(), but not call kobject_put(glue_dir), the glue dir is still in parent's kset list. Meanwhile, path1 find the glue dir from the glue_dirs.list. Path2 may release glue dir before path1 call kobject_get(). So kernel will report the warning and bug_on. This is a "classic" problem we have of a kref in a list that can be found while the last instance could be removed at the same time. This patch reuse gdp_mutex to fix this race condition. The following calltrace is captured in kernel 3.4, but the latest kernel still has this bug. ----------------------------------------------------- <4>[ 3965.441471] WARNING: at ...include/linux/kref.h:41 kobject_get+0x33/0x40() <4>[ 3965.441474] Hardware name: Romley <4>[ 3965.441475] Modules linked in: isd_iop(O) isd_xda(O)... ... <4>[ 3965.441605] Call Trace: <4>[ 3965.441611] [] warn_slowpath_common+0x7a/0xb0 <4>[ 3965.441615] [] warn_slowpath_null+0x15/0x20 <4>[ 3965.441618] [] kobject_get+0x33/0x40 <4>[ 3965.441624] [] get_device_parent.isra.11+0x135/0x1f0 <4>[ 3965.441627] [] device_add+0xd4/0x6d0 <4>[ 3965.441631] [] ? dev_set_name+0x3c/0x40 .... <2>[ 3965.441912] kernel BUG at ..../fs/sysfs/group.c:65! <4>[ 3965.441915] invalid opcode: 0000 [#1] SMP ... <4>[ 3965.686743] [] sysfs_create_group+0xe/0x10 <4>[ 3965.686748] [] blk_trace_init_sysfs+0x14/0x20 <4>[ 3965.686753] [] blk_register_queue+0x3b/0x120 <4>[ 3965.686756] [] add_disk+0x1cc/0x490 .... ------------------------------------------------------- Signed-off-by: Yijing Wang Signed-off-by: Weng Meiling Cc: #3.4+ Signed-off-by: Greg Kroah-Hartman --- drivers/base/core.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/base/core.c b/drivers/base/core.c index 14d162952c3..842d04707de 100644 --- a/drivers/base/core.c +++ b/drivers/base/core.c @@ -724,12 +724,12 @@ class_dir_create_and_add(struct class *class, struct kobject *parent_kobj) return &dir->kobj; } +static DEFINE_MUTEX(gdp_mutex); static struct kobject *get_device_parent(struct device *dev, struct device *parent) { if (dev->class) { - static DEFINE_MUTEX(gdp_mutex); struct kobject *kobj = NULL; struct kobject *parent_kobj; struct kobject *k; @@ -793,7 +793,9 @@ static void cleanup_glue_dir(struct device *dev, struct kobject *glue_dir) glue_dir->kset != &dev->class->p->glue_dirs) return; + mutex_lock(&gdp_mutex); kobject_put(glue_dir); + mutex_unlock(&gdp_mutex); } static void cleanup_device_parent(struct device *dev) -- cgit v1.2.3-70-g09d2 From 1910195423e7bea4c01c42bfe3f81792a6e969bb Mon Sep 17 00:00:00 2001 From: Mark Knibbs Date: Tue, 4 Nov 2014 13:00:15 +0000 Subject: USB: Update default usb-storage delay_use value in kernel-parameters.txt Back in 2010 the default usb-storage delay_use time was reduced from 5 to 1 second (commit a4a47bc03fe520e95e0c4212bf97c86545fb14f9), but kernel-parameters.txt wasn't updated to reflect that. Signed-off-by: Mark Knibbs Signed-off-by: Greg Kroah-Hartman --- Documentation/kernel-parameters.txt | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 4c81a860cc2..479f33204a3 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -3621,7 +3621,7 @@ bytes respectively. Such letter suffixes can also be entirely omitted. usb-storage.delay_use= [UMS] The delay in seconds before a new device is - scanned for Logical Units (default 5). + scanned for Logical Units (default 1). usb-storage.quirks= [UMS] A list of quirks entries to supplement or -- cgit v1.2.3-70-g09d2 From ca1f8da9ac5ce6e63d8f6933f83fabc1f3f961f4 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Tue, 4 Nov 2014 23:46:27 +0100 Subject: i2c: remove FSF address We have a central copy of the GPL for that. Some addresses were already outdated. Signed-off-by: Wolfram Sang --- drivers/i2c/algos/i2c-algo-bit.c | 5 ----- drivers/i2c/algos/i2c-algo-pca.c | 5 ----- drivers/i2c/algos/i2c-algo-pcf.c | 5 ----- drivers/i2c/algos/i2c-algo-pcf.h | 7 +------ drivers/i2c/busses/i2c-ali1535.c | 4 ---- drivers/i2c/busses/i2c-ali15x3.c | 4 ---- drivers/i2c/busses/i2c-amd756-s4882.c | 4 ---- drivers/i2c/busses/i2c-amd756.c | 4 ---- drivers/i2c/busses/i2c-au1550.c | 4 ---- drivers/i2c/busses/i2c-cpm.c | 4 ---- drivers/i2c/busses/i2c-davinci.c | 4 ---- drivers/i2c/busses/i2c-designware-core.c | 4 ---- drivers/i2c/busses/i2c-designware-core.h | 4 ---- drivers/i2c/busses/i2c-designware-pcidrv.c | 4 ---- drivers/i2c/busses/i2c-designware-platdrv.c | 4 ---- drivers/i2c/busses/i2c-eg20t.c | 4 ---- drivers/i2c/busses/i2c-elektor.c | 6 +----- drivers/i2c/busses/i2c-hydra.c | 4 ---- drivers/i2c/busses/i2c-i801.c | 4 ---- drivers/i2c/busses/i2c-imx.c | 5 ----- drivers/i2c/busses/i2c-iop3xx.h | 6 +----- drivers/i2c/busses/i2c-isch.c | 4 ---- drivers/i2c/busses/i2c-ismt.c | 4 ---- drivers/i2c/busses/i2c-nforce2-s4985.c | 4 ---- drivers/i2c/busses/i2c-nforce2.c | 4 ---- drivers/i2c/busses/i2c-omap.c | 4 ---- drivers/i2c/busses/i2c-parport-light.c | 4 ---- drivers/i2c/busses/i2c-parport.c | 4 ---- drivers/i2c/busses/i2c-parport.h | 4 ---- drivers/i2c/busses/i2c-pasemi.c | 4 ---- drivers/i2c/busses/i2c-pca-isa.c | 4 ---- drivers/i2c/busses/i2c-piix4.c | 4 ---- drivers/i2c/busses/i2c-pmcmsp.c | 4 ---- drivers/i2c/busses/i2c-powermac.c | 4 ---- drivers/i2c/busses/i2c-s3c2410.c | 4 ---- drivers/i2c/busses/i2c-sh_mobile.c | 4 ---- drivers/i2c/busses/i2c-sibyte.c | 4 ---- drivers/i2c/busses/i2c-simtec.c | 4 ---- drivers/i2c/busses/i2c-sis5595.c | 4 ---- drivers/i2c/busses/i2c-sis630.c | 4 ---- drivers/i2c/busses/i2c-sis96x.c | 4 ---- drivers/i2c/busses/i2c-taos-evm.c | 4 ---- drivers/i2c/busses/i2c-via.c | 4 ---- drivers/i2c/busses/i2c-viapro.c | 4 ---- drivers/i2c/busses/i2c-xiic.c | 4 ---- drivers/i2c/busses/scx200_acb.c | 4 ---- drivers/i2c/i2c-boardinfo.c | 5 ----- drivers/i2c/i2c-core.c | 7 +------ drivers/i2c/i2c-core.h | 5 ----- drivers/i2c/i2c-dev.c | 5 ----- drivers/i2c/i2c-smbus.c | 5 ----- drivers/i2c/i2c-stub.c | 4 ---- 52 files changed, 4 insertions(+), 222 deletions(-) diff --git a/drivers/i2c/algos/i2c-algo-bit.c b/drivers/i2c/algos/i2c-algo-bit.c index 65ef9664d5d..899bede81b3 100644 --- a/drivers/i2c/algos/i2c-algo-bit.c +++ b/drivers/i2c/algos/i2c-algo-bit.c @@ -12,11 +12,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - MA 02110-1301 USA. * ------------------------------------------------------------------------- */ /* With some changes from Frodo Looijaard , Kyösti Mälkki diff --git a/drivers/i2c/algos/i2c-algo-pca.c b/drivers/i2c/algos/i2c-algo-pca.c index 8b10f88b13d..580dbf05c14 100644 --- a/drivers/i2c/algos/i2c-algo-pca.c +++ b/drivers/i2c/algos/i2c-algo-pca.c @@ -12,11 +12,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301 USA. */ #include diff --git a/drivers/i2c/algos/i2c-algo-pcf.c b/drivers/i2c/algos/i2c-algo-pcf.c index 34370090b75..270d84bfc2c 100644 --- a/drivers/i2c/algos/i2c-algo-pcf.c +++ b/drivers/i2c/algos/i2c-algo-pcf.c @@ -14,11 +14,6 @@ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301 USA. - * * With some changes from Kyösti Mälkki and * Frodo Looijaard , and also from Martin Bailey * diff --git a/drivers/i2c/algos/i2c-algo-pcf.h b/drivers/i2c/algos/i2c-algo-pcf.h index 1ec703ee788..262ee801975 100644 --- a/drivers/i2c/algos/i2c-algo-pcf.h +++ b/drivers/i2c/algos/i2c-algo-pcf.h @@ -12,12 +12,7 @@ This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - MA 02110-1301 USA. */ + GNU General Public License for more details. */ /* -------------------------------------------------------------------- */ /* With some changes from Frodo Looijaard */ diff --git a/drivers/i2c/busses/i2c-ali1535.c b/drivers/i2c/busses/i2c-ali1535.c index 451e305f797..4f2d7886828 100644 --- a/drivers/i2c/busses/i2c-ali1535.c +++ b/drivers/i2c/busses/i2c-ali1535.c @@ -14,10 +14,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* diff --git a/drivers/i2c/busses/i2c-ali15x3.c b/drivers/i2c/busses/i2c-ali15x3.c index 2fa21ce9682..45c5c488302 100644 --- a/drivers/i2c/busses/i2c-ali15x3.c +++ b/drivers/i2c/busses/i2c-ali15x3.c @@ -12,10 +12,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* diff --git a/drivers/i2c/busses/i2c-amd756-s4882.c b/drivers/i2c/busses/i2c-amd756-s4882.c index 41fc6837fb8..65e32405497 100644 --- a/drivers/i2c/busses/i2c-amd756-s4882.c +++ b/drivers/i2c/busses/i2c-amd756-s4882.c @@ -12,10 +12,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* diff --git a/drivers/i2c/busses/i2c-amd756.c b/drivers/i2c/busses/i2c-amd756.c index a16f7289135..6c7113d990f 100644 --- a/drivers/i2c/busses/i2c-amd756.c +++ b/drivers/i2c/busses/i2c-amd756.c @@ -15,10 +15,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* diff --git a/drivers/i2c/busses/i2c-au1550.c b/drivers/i2c/busses/i2c-au1550.c index 8762458ca7d..6f8c0756e35 100644 --- a/drivers/i2c/busses/i2c-au1550.c +++ b/drivers/i2c/busses/i2c-au1550.c @@ -21,10 +21,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. */ #include diff --git a/drivers/i2c/busses/i2c-cpm.c b/drivers/i2c/busses/i2c-cpm.c index f3b89a4698b..5bdbc71698d 100644 --- a/drivers/i2c/busses/i2c-cpm.c +++ b/drivers/i2c/busses/i2c-cpm.c @@ -23,10 +23,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ #include diff --git a/drivers/i2c/busses/i2c-davinci.c b/drivers/i2c/busses/i2c-davinci.c index 4d961471912..d15b7c9b921 100644 --- a/drivers/i2c/busses/i2c-davinci.c +++ b/drivers/i2c/busses/i2c-davinci.c @@ -17,10 +17,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. * ---------------------------------------------------------------------------- * */ diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c index 3c20e4bd6dd..edca99dbba2 100644 --- a/drivers/i2c/busses/i2c-designware-core.c +++ b/drivers/i2c/busses/i2c-designware-core.c @@ -18,10 +18,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. * ---------------------------------------------------------------------------- * */ diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h index d66b6cbc9ed..5a410ef17ab 100644 --- a/drivers/i2c/busses/i2c-designware-core.h +++ b/drivers/i2c/busses/i2c-designware-core.h @@ -18,10 +18,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. * ---------------------------------------------------------------------------- * */ diff --git a/drivers/i2c/busses/i2c-designware-pcidrv.c b/drivers/i2c/busses/i2c-designware-pcidrv.c index d31d313ab4f..acb40f95db7 100644 --- a/drivers/i2c/busses/i2c-designware-pcidrv.c +++ b/drivers/i2c/busses/i2c-designware-pcidrv.c @@ -19,10 +19,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. * ---------------------------------------------------------------------------- * */ diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c index a7431150acf..373dd4d4776 100644 --- a/drivers/i2c/busses/i2c-designware-platdrv.c +++ b/drivers/i2c/busses/i2c-designware-platdrv.c @@ -18,10 +18,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. * ---------------------------------------------------------------------------- * */ diff --git a/drivers/i2c/busses/i2c-eg20t.c b/drivers/i2c/busses/i2c-eg20t.c index a44ea13d143..76e699f9ed9 100644 --- a/drivers/i2c/busses/i2c-eg20t.c +++ b/drivers/i2c/busses/i2c-eg20t.c @@ -9,10 +9,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307, USA. */ #include diff --git a/drivers/i2c/busses/i2c-elektor.c b/drivers/i2c/busses/i2c-elektor.c index 485497066ed..92e8c0ce162 100644 --- a/drivers/i2c/busses/i2c-elektor.c +++ b/drivers/i2c/busses/i2c-elektor.c @@ -12,11 +12,7 @@ This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ + GNU General Public License for more details. */ /* ------------------------------------------------------------------------- */ /* With some changes from Kyösti Mälkki and even diff --git a/drivers/i2c/busses/i2c-hydra.c b/drivers/i2c/busses/i2c-hydra.c index 14d2b76de25..b7864cf42a7 100644 --- a/drivers/i2c/busses/i2c-hydra.c +++ b/drivers/i2c/busses/i2c-hydra.c @@ -15,10 +15,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ #include diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c index 7cfc183b3d6..6ab4f1cb21f 100644 --- a/drivers/i2c/busses/i2c-i801.c +++ b/drivers/i2c/busses/i2c-i801.c @@ -15,10 +15,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c index c48e46af670..e9fb7cf7861 100644 --- a/drivers/i2c/busses/i2c-imx.c +++ b/drivers/i2c/busses/i2c-imx.c @@ -11,11 +11,6 @@ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, - * USA. - * * Author: * Darius Augulis, Teltonika Inc. * diff --git a/drivers/i2c/busses/i2c-iop3xx.h b/drivers/i2c/busses/i2c-iop3xx.h index 097e270955d..2d6929c2bd9 100644 --- a/drivers/i2c/busses/i2c-iop3xx.h +++ b/drivers/i2c/busses/i2c-iop3xx.h @@ -11,11 +11,7 @@ This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ + GNU General Public License for more details. */ /* ------------------------------------------------------------------------- */ diff --git a/drivers/i2c/busses/i2c-isch.c b/drivers/i2c/busses/i2c-isch.c index cf99dbf21fd..113293d275f 100644 --- a/drivers/i2c/busses/i2c-isch.c +++ b/drivers/i2c/busses/i2c-isch.c @@ -14,10 +14,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* diff --git a/drivers/i2c/busses/i2c-ismt.c b/drivers/i2c/busses/i2c-ismt.c index 3f6ecbfb9a5..f2b0ff01163 100644 --- a/drivers/i2c/busses/i2c-ismt.c +++ b/drivers/i2c/busses/i2c-ismt.c @@ -14,10 +14,6 @@ * WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU * General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. * The full GNU General Public License is included in this distribution * in the file called LICENSE.GPL. * diff --git a/drivers/i2c/busses/i2c-nforce2-s4985.c b/drivers/i2c/busses/i2c-nforce2-s4985.c index b170bdffb5d..88eda09e73c 100644 --- a/drivers/i2c/busses/i2c-nforce2-s4985.c +++ b/drivers/i2c/busses/i2c-nforce2-s4985.c @@ -12,10 +12,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* diff --git a/drivers/i2c/busses/i2c-nforce2.c b/drivers/i2c/busses/i2c-nforce2.c index ee3a76c7ae9..70b3c915850 100644 --- a/drivers/i2c/busses/i2c-nforce2.c +++ b/drivers/i2c/busses/i2c-nforce2.c @@ -17,10 +17,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* diff --git a/drivers/i2c/busses/i2c-omap.c b/drivers/i2c/busses/i2c-omap.c index 0dffb0e62c3..26942c159de 100644 --- a/drivers/i2c/busses/i2c-omap.c +++ b/drivers/i2c/busses/i2c-omap.c @@ -22,10 +22,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ #include diff --git a/drivers/i2c/busses/i2c-parport-light.c b/drivers/i2c/busses/i2c-parport-light.c index 62f55fe624c..d1f625f923c 100644 --- a/drivers/i2c/busses/i2c-parport-light.c +++ b/drivers/i2c/busses/i2c-parport-light.c @@ -18,10 +18,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. * ------------------------------------------------------------------------ */ #include diff --git a/drivers/i2c/busses/i2c-parport.c b/drivers/i2c/busses/i2c-parport.c index a27aae2d675..a1fac5aa9ba 100644 --- a/drivers/i2c/busses/i2c-parport.c +++ b/drivers/i2c/busses/i2c-parport.c @@ -18,10 +18,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. * ------------------------------------------------------------------------ */ #include diff --git a/drivers/i2c/busses/i2c-parport.h b/drivers/i2c/busses/i2c-parport.h index e572f3aac0f..4e129453680 100644 --- a/drivers/i2c/busses/i2c-parport.h +++ b/drivers/i2c/busses/i2c-parport.h @@ -12,10 +12,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. * ------------------------------------------------------------------------ */ #define PORT_DATA 0 diff --git a/drivers/i2c/busses/i2c-pasemi.c b/drivers/i2c/busses/i2c-pasemi.c index 7a9dce43e11..df1dbc92a02 100644 --- a/drivers/i2c/busses/i2c-pasemi.c +++ b/drivers/i2c/busses/i2c-pasemi.c @@ -11,10 +11,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include diff --git a/drivers/i2c/busses/i2c-pca-isa.c b/drivers/i2c/busses/i2c-pca-isa.c index 323f061a316..e0eb4ca0102 100644 --- a/drivers/i2c/busses/i2c-pca-isa.c +++ b/drivers/i2c/busses/i2c-pca-isa.c @@ -12,10 +12,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ #include diff --git a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c index a6f54ba27e2..67cbec6796a 100644 --- a/drivers/i2c/busses/i2c-piix4.c +++ b/drivers/i2c/busses/i2c-piix4.c @@ -11,10 +11,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* diff --git a/drivers/i2c/busses/i2c-pmcmsp.c b/drivers/i2c/busses/i2c-pmcmsp.c index 8564768fee3..177834e2d84 100644 --- a/drivers/i2c/busses/i2c-pmcmsp.c +++ b/drivers/i2c/busses/i2c-pmcmsp.c @@ -18,10 +18,6 @@ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - * - * You should have received a copy of the GNU General Public License along - * with this program; if not, write to the Free Software Foundation, Inc., - * 675 Mass Ave, Cambridge, MA 02139, USA. */ #include diff --git a/drivers/i2c/busses/i2c-powermac.c b/drivers/i2c/busses/i2c-powermac.c index 01e967763c2..60a53c169ed 100644 --- a/drivers/i2c/busses/i2c-powermac.c +++ b/drivers/i2c/busses/i2c-powermac.c @@ -14,10 +14,6 @@ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - */ #include diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c index e3b0337faeb..65244774bfa 100644 --- a/drivers/i2c/busses/i2c-s3c2410.c +++ b/drivers/i2c/busses/i2c-s3c2410.c @@ -14,10 +14,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include diff --git a/drivers/i2c/busses/i2c-sh_mobile.c b/drivers/i2c/busses/i2c-sh_mobile.c index 8b5e79cb446..4855188747c 100644 --- a/drivers/i2c/busses/i2c-sh_mobile.c +++ b/drivers/i2c/busses/i2c-sh_mobile.c @@ -14,10 +14,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include diff --git a/drivers/i2c/busses/i2c-sibyte.c b/drivers/i2c/busses/i2c-sibyte.c index 0fe505d7abe..2b6219d86b0 100644 --- a/drivers/i2c/busses/i2c-sibyte.c +++ b/drivers/i2c/busses/i2c-sibyte.c @@ -12,10 +12,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. */ #include diff --git a/drivers/i2c/busses/i2c-simtec.c b/drivers/i2c/busses/i2c-simtec.c index 964e5c6f84a..15ac8395dcd 100644 --- a/drivers/i2c/busses/i2c-simtec.c +++ b/drivers/i2c/busses/i2c-simtec.c @@ -12,10 +12,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include diff --git a/drivers/i2c/busses/i2c-sis5595.c b/drivers/i2c/busses/i2c-sis5595.c index ac9bc33acef..7d58a40faf2 100644 --- a/drivers/i2c/busses/i2c-sis5595.c +++ b/drivers/i2c/busses/i2c-sis5595.c @@ -11,10 +11,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* Note: we assume there can only be one SIS5595 with one SMBus interface */ diff --git a/drivers/i2c/busses/i2c-sis630.c b/drivers/i2c/busses/i2c-sis630.c index c6366733008..1e6805b5cef 100644 --- a/drivers/i2c/busses/i2c-sis630.c +++ b/drivers/i2c/busses/i2c-sis630.c @@ -10,10 +10,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* diff --git a/drivers/i2c/busses/i2c-sis96x.c b/drivers/i2c/busses/i2c-sis96x.c index 8dc2fc5f74f..44b90442607 100644 --- a/drivers/i2c/busses/i2c-sis96x.c +++ b/drivers/i2c/busses/i2c-sis96x.c @@ -10,10 +10,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* diff --git a/drivers/i2c/busses/i2c-taos-evm.c b/drivers/i2c/busses/i2c-taos-evm.c index 10855a0b7e7..4c7fc2d4701 100644 --- a/drivers/i2c/busses/i2c-taos-evm.c +++ b/drivers/i2c/busses/i2c-taos-evm.c @@ -13,10 +13,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA */ #include diff --git a/drivers/i2c/busses/i2c-via.c b/drivers/i2c/busses/i2c-via.c index f4a1ed75761..59b1d233ca7 100644 --- a/drivers/i2c/busses/i2c-via.c +++ b/drivers/i2c/busses/i2c-via.c @@ -12,10 +12,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ #include diff --git a/drivers/i2c/busses/i2c-viapro.c b/drivers/i2c/busses/i2c-viapro.c index 6841200b6e5..0ee2646f3b0 100644 --- a/drivers/i2c/busses/i2c-viapro.c +++ b/drivers/i2c/busses/i2c-viapro.c @@ -13,10 +13,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ /* diff --git a/drivers/i2c/busses/i2c-xiic.c b/drivers/i2c/busses/i2c-xiic.c index ade9223912d..cc65ea0b818 100644 --- a/drivers/i2c/busses/i2c-xiic.c +++ b/drivers/i2c/busses/i2c-xiic.c @@ -12,10 +12,6 @@ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - * * * This code was implemented by Mocean Laboratories AB when porting linux * to the automotive development board Russellville. The copyright holder diff --git a/drivers/i2c/busses/scx200_acb.c b/drivers/i2c/busses/scx200_acb.c index ff3f5747e43..5153354b1a6 100644 --- a/drivers/i2c/busses/scx200_acb.c +++ b/drivers/i2c/busses/scx200_acb.c @@ -17,10 +17,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt diff --git a/drivers/i2c/i2c-boardinfo.c b/drivers/i2c/i2c-boardinfo.c index f24cc64e2e8..90e32295930 100644 --- a/drivers/i2c/i2c-boardinfo.c +++ b/drivers/i2c/i2c-boardinfo.c @@ -10,11 +10,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301 USA. */ #include diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c index 2f90ac6a7f7..17a1853c6c2 100644 --- a/drivers/i2c/i2c-core.c +++ b/drivers/i2c/i2c-core.c @@ -10,12 +10,7 @@ This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - MA 02110-1301 USA. */ + GNU General Public License for more details. */ /* ------------------------------------------------------------------------- */ /* With some changes from Kyösti Mälkki . diff --git a/drivers/i2c/i2c-core.h b/drivers/i2c/i2c-core.h index 18a8fd21d2c..17700bfddcf 100644 --- a/drivers/i2c/i2c-core.h +++ b/drivers/i2c/i2c-core.h @@ -10,11 +10,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301 USA. */ #include diff --git a/drivers/i2c/i2c-dev.c b/drivers/i2c/i2c-dev.c index 80b47e8ce03..71c7a3975b6 100644 --- a/drivers/i2c/i2c-dev.c +++ b/drivers/i2c/i2c-dev.c @@ -14,11 +14,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - MA 02110-1301 USA. */ /* Note that this is a complete rewrite of Simon Vogl's i2c-dev module. diff --git a/drivers/i2c/i2c-smbus.c b/drivers/i2c/i2c-smbus.c index fc99f0d6b4a..9ebf9cb4ad7 100644 --- a/drivers/i2c/i2c-smbus.c +++ b/drivers/i2c/i2c-smbus.c @@ -13,11 +13,6 @@ * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, - * MA 02110-1301 USA. */ #include diff --git a/drivers/i2c/i2c-stub.c b/drivers/i2c/i2c-stub.c index d241aa295d9..af2a94e1140 100644 --- a/drivers/i2c/i2c-stub.c +++ b/drivers/i2c/i2c-stub.c @@ -13,10 +13,6 @@ but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */ #define DEBUG 1 -- cgit v1.2.3-70-g09d2 From 11cfbfb098b22d3e57f1f2be217cad20e2d48463 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Mon, 3 Nov 2014 21:16:16 +0100 Subject: i2c: at91: don't account as iowait iowait is for blkio [1]. I2C shouldn't use it. [1] https://lkml.org/lkml/2014/11/3/317 Signed-off-by: Wolfram Sang Acked-by: Ludovic Desroches Cc: stable@kernel.org --- drivers/i2c/busses/i2c-at91.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c index 917d54588d9..e05a672db3e 100644 --- a/drivers/i2c/busses/i2c-at91.c +++ b/drivers/i2c/busses/i2c-at91.c @@ -434,7 +434,7 @@ static int at91_do_twi_transfer(struct at91_twi_dev *dev) } } - ret = wait_for_completion_io_timeout(&dev->cmd_complete, + ret = wait_for_completion_timeout(&dev->cmd_complete, dev->adapter.timeout); if (ret == 0) { dev_err(dev->dev, "controller timed out\n"); -- cgit v1.2.3-70-g09d2 From e4df3a0b62285130ac0a35cf07678c154ffb649d Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Thu, 30 Oct 2014 15:59:37 +0200 Subject: i2c: core: Dispose OF IRQ mapping at client removal time Clients instantiated from OF get an IRQ mapping created at device registration time. Dispose the mapping when the client is removed. Signed-off-by: Laurent Pinchart Signed-off-by: Wolfram Sang Cc: stable@kernel.org --- drivers/i2c/i2c-core.c | 3 +++ 1 file changed, 3 insertions(+) diff --git a/drivers/i2c/i2c-core.c b/drivers/i2c/i2c-core.c index 17a1853c6c2..f43b4e11647 100644 --- a/drivers/i2c/i2c-core.c +++ b/drivers/i2c/i2c-core.c @@ -665,6 +665,9 @@ static int i2c_device_remove(struct device *dev) status = driver->remove(client); } + if (dev->of_node) + irq_dispose_mapping(client->irq); + dev_pm_domain_detach(&client->dev, true); return status; } -- cgit v1.2.3-70-g09d2 From 9c6026994c2a18473c9ef9ed77e8cf8e344f4357 Mon Sep 17 00:00:00 2001 From: Aristeu Rozanski Date: Thu, 16 Oct 2014 11:49:49 -0400 Subject: tiny: reverse logic for DISABLE_DEV_COREDUMP It's desirable for allnconfig and tinyconfig targets to result in the least amount of code possible. DISABLE_DEV_COREDUMP exists as a way to switch off DEV_COREDUMP regardless if any drivers select WANT_DEV_COREDUMP. This patch renames the option to ENABLE_DEV_COREDUMP and setting it to 'n' (as in allnconfig or tinyconfig) will effectively disable device coredump. Cc: Josh Triplett Reviewed-by: Josh Triplett Signed-off-by: Aristeu Rozanski Reviewed-by: Johannes Berg Acked-by: Johannes Berg Signed-off-by: Greg Kroah-Hartman --- drivers/base/Kconfig | 19 +++++++++++-------- 1 file changed, 11 insertions(+), 8 deletions(-) diff --git a/drivers/base/Kconfig b/drivers/base/Kconfig index 61a33f4ba60..c29d1600e90 100644 --- a/drivers/base/Kconfig +++ b/drivers/base/Kconfig @@ -171,20 +171,23 @@ config WANT_DEV_COREDUMP Drivers should "select" this option if they desire to use the device coredump mechanism. -config DISABLE_DEV_COREDUMP - bool "Disable device coredump" if EXPERT +config ENABLE_DEV_COREDUMP + bool "Enable device coredump" if EXPERT + default y help - Disable the device coredump mechanism despite drivers wanting to - use it; this allows for more sensitive systems or systems that - don't want to ever access the information to not have the code, - nor keep any data. + This option controls if the device coredump mechanism is available or + not; if disabled, the mechanism will be omitted even if drivers that + can use it are enabled. + Say 'N' for more sensitive systems or systems that don't want + to ever access the information to not have the code, nor keep any + data. - If unsure, say N. + If unsure, say Y. config DEV_COREDUMP bool default y if WANT_DEV_COREDUMP - depends on !DISABLE_DEV_COREDUMP + depends on ENABLE_DEV_COREDUMP config DEBUG_DRIVER bool "Driver Core verbose debug messages" -- cgit v1.2.3-70-g09d2 From cd3d9ea142c9fd47351e79fe30c7ae2c86302cda Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Thu, 30 Oct 2014 10:00:35 +0100 Subject: tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP The ENABLE_DEV_COREDUMP option is misleading as it implies that it gets the framework enabled, this isn't true it just allows it to get enabled if a driver needs it. Rename it to ALLOW_DEV_COREDUMP to better capture its semantics. Signed-off-by: Johannes Berg Reviewed-by: Josh Triplett Acked-by: Aristeu Rozanski Signed-off-by: Greg Kroah-Hartman --- drivers/base/Kconfig | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/base/Kconfig b/drivers/base/Kconfig index c29d1600e90..df04227d00c 100644 --- a/drivers/base/Kconfig +++ b/drivers/base/Kconfig @@ -171,8 +171,8 @@ config WANT_DEV_COREDUMP Drivers should "select" this option if they desire to use the device coredump mechanism. -config ENABLE_DEV_COREDUMP - bool "Enable device coredump" if EXPERT +config ALLOW_DEV_COREDUMP + bool "Allow device coredump" if EXPERT default y help This option controls if the device coredump mechanism is available or @@ -187,7 +187,7 @@ config ENABLE_DEV_COREDUMP config DEV_COREDUMP bool default y if WANT_DEV_COREDUMP - depends on ENABLE_DEV_COREDUMP + depends on ALLOW_DEV_COREDUMP config DEBUG_DRIVER bool "Driver Core verbose debug messages" -- cgit v1.2.3-70-g09d2 From 92c9e0c780e61f821ab8a08f0d4d4fd33ba1197c Mon Sep 17 00:00:00 2001 From: Andreas Färber Date: Thu, 6 Nov 2014 18:22:10 +0100 Subject: ARM: dts: zynq: Enable PL clocks for Parallella MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The Parallella board comes with a U-Boot bootloader that loads one of two predefined FPGA bitstreams before booting the kernel. Both define an AXI interface to the on-board Epiphany processor. Enable clocks FCLK0..FCLK3 for the Programmable Logic by default. Otherwise accessing, e.g., the ESYSRESET register freezes the board, as seen with the Epiphany SDK tools e-reset and e-hw-rev, using /dev/mem. Cc: # 3.17.x Signed-off-by: Andreas Färber Acked-by: Michal Simek Signed-off-by: Olof Johansson --- arch/arm/boot/dts/zynq-parallella.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/zynq-parallella.dts b/arch/arm/boot/dts/zynq-parallella.dts index e1f51ca127f..0429bbd89fb 100644 --- a/arch/arm/boot/dts/zynq-parallella.dts +++ b/arch/arm/boot/dts/zynq-parallella.dts @@ -34,6 +34,10 @@ }; }; +&clkc { + fclk-enable = <0xf>; +}; + &gem0 { status = "okay"; phy-mode = "rgmii-id"; -- cgit v1.2.3-70-g09d2 From 206c5f60a3d902bc4b56dab2de3e88de5eb06108 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sun, 9 Nov 2014 14:55:29 -0800 Subject: Linux 3.18-rc4 --- Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Makefile b/Makefile index ffc1ce2b034..bc7eb6ada96 100644 --- a/Makefile +++ b/Makefile @@ -1,7 +1,7 @@ VERSION = 3 PATCHLEVEL = 18 SUBLEVEL = 0 -EXTRAVERSION = -rc3 +EXTRAVERSION = -rc4 NAME = Diseased Newt # *DOCUMENTATION* -- cgit v1.2.3-70-g09d2