From bb249aad82b93674281d8b76a0c9be2ba1d92d78 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sat, 27 Jul 2013 12:21:52 +0100 Subject: spi/tegra114: Factor runtime PM out into transfer prepare/unprepare Currently the tegra114 driver acquires a runtime PM reference for the duration of each transfer. This may result in the IP being powered down between transfers which would be at best wasteful. Instead it is better to do this in the callbacks that are generated before and after starting a series of transfers, keeping the IP powered throughout. Signed-off-by: Mark Brown Acked-by: Laxman Dewangan --- drivers/spi/spi-tegra114.c | 34 +++++++++++++++++++++++++--------- 1 file changed, 25 insertions(+), 9 deletions(-) diff --git a/drivers/spi/spi-tegra114.c b/drivers/spi/spi-tegra114.c index e8f542ab893..d85882da853 100644 --- a/drivers/spi/spi-tegra114.c +++ b/drivers/spi/spi-tegra114.c @@ -803,6 +803,20 @@ static int tegra_spi_setup(struct spi_device *spi) return 0; } +static int tegra_spi_prepare_transfer(struct spi_master *spi) +{ + struct tegra_spi_data *tspi = spi_master_get_devdata(spi); + int ret; + + ret = pm_runtime_get_sync(tspi->dev); + if (ret < 0) { + dev_err(tspi->dev, "runtime PM get failed: %d\n", ret); + return ret; + } + + return ret; +} + static int tegra_spi_transfer_one_message(struct spi_master *master, struct spi_message *msg) { @@ -816,14 +830,6 @@ static int tegra_spi_transfer_one_message(struct spi_master *master, msg->status = 0; msg->actual_length = 0; - ret = pm_runtime_get_sync(tspi->dev); - if (ret < 0) { - dev_err(tspi->dev, "runtime PM get failed: %d\n", ret); - msg->status = ret; - spi_finalize_current_message(master); - return ret; - } - single_xfer = list_is_singular(&msg->transfers); list_for_each_entry(xfer, &msg->transfers, transfer_list) { INIT_COMPLETION(tspi->xfer_completion); @@ -859,12 +865,20 @@ static int tegra_spi_transfer_one_message(struct spi_master *master, ret = 0; exit: tegra_spi_writel(tspi, tspi->def_command1_reg, SPI_COMMAND1); - pm_runtime_put(tspi->dev); msg->status = ret; spi_finalize_current_message(master); return ret; } +static int tegra_spi_unprepare_transfer(struct spi_master *spi) +{ + struct tegra_spi_data *tspi = spi_master_get_devdata(spi); + + pm_runtime_put(tspi->dev); + + return 0; +} + static irqreturn_t handle_cpu_based_xfer(struct tegra_spi_data *tspi) { struct spi_transfer *t = tspi->curr_xfer; @@ -1050,7 +1064,9 @@ static int tegra_spi_probe(struct platform_device *pdev) /* the spi->mode bits understood by this driver: */ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; master->setup = tegra_spi_setup; + master->prepare_transfer_hardware = tegra_spi_prepare_transfer; master->transfer_one_message = tegra_spi_transfer_one_message; + master->unprepare_transfer_hardware = tegra_spi_unprepare_transfer; master->num_chipselect = MAX_CHIP_SELECT; master->bus_num = -1; -- cgit v1.2.3-70-g09d2 From 9f178c22fb0e88f4e84f7a66be8326f63b91e7e3 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sat, 27 Jul 2013 12:29:58 +0100 Subject: spi/tegra-sflash: Factor runtime PM out into transfer prepare/unprepare Currently the tegra sflash driver acquires a runtime PM reference for the duration of each transfer. This may result in the IP being powered down between transfers which would be at best wasteful. Instead it is better to do this in the callbacks that are generated before and after starting a series of transfers, keeping the IP powered throughout. Signed-off-by: Mark Brown Acked-by: Laxman Dewangan --- drivers/spi/spi-tegra20-sflash.c | 32 +++++++++++++++++++++++++------- 1 file changed, 25 insertions(+), 7 deletions(-) diff --git a/drivers/spi/spi-tegra20-sflash.c b/drivers/spi/spi-tegra20-sflash.c index c1d5d95e70e..f871c4ee6ad 100644 --- a/drivers/spi/spi-tegra20-sflash.c +++ b/drivers/spi/spi-tegra20-sflash.c @@ -325,6 +325,20 @@ static int tegra_sflash_setup(struct spi_device *spi) return 0; } +static int tegra_sflash_prepare_transfer(struct spi_master *spi) +{ + struct tegra_sflash_data *tsd = spi_master_get_devdata(spi); + int ret; + + ret = pm_runtime_get_sync(tsd->dev); + if (ret < 0) { + dev_err(tsd->dev, "runtime PM get failed: %d\n", ret); + return ret; + } + + return ret; +} + static int tegra_sflash_transfer_one_message(struct spi_master *master, struct spi_message *msg) { @@ -335,12 +349,6 @@ static int tegra_sflash_transfer_one_message(struct spi_master *master, struct spi_device *spi = msg->spi; int ret; - ret = pm_runtime_get_sync(tsd->dev); - if (ret < 0) { - dev_err(tsd->dev, "pm_runtime_get() failed, err = %d\n", ret); - return ret; - } - msg->status = 0; msg->actual_length = 0; single_xfer = list_is_singular(&msg->transfers); @@ -380,10 +388,18 @@ exit: tegra_sflash_writel(tsd, tsd->def_command_reg, SPI_COMMAND); msg->status = ret; spi_finalize_current_message(master); - pm_runtime_put(tsd->dev); return ret; } +static int tegra_sflash_unprepare_transfer(struct spi_master *spi) +{ + struct tegra_sflash_data *tsd = spi_master_get_devdata(spi); + + pm_runtime_put(tsd->dev); + + return 0; +} + static irqreturn_t handle_cpu_based_xfer(struct tegra_sflash_data *tsd) { struct spi_transfer *t = tsd->curr_xfer; @@ -476,7 +492,9 @@ static int tegra_sflash_probe(struct platform_device *pdev) /* the spi->mode bits understood by this driver: */ master->mode_bits = SPI_CPOL | SPI_CPHA; master->setup = tegra_sflash_setup; + master->prepare_transfer_hardware = tegra_sflash_prepare_transfer; master->transfer_one_message = tegra_sflash_transfer_one_message; + master->unprepare_transfer_hardware = tegra_sflash_unprepare_transfer; master->num_chipselect = MAX_CHIP_SELECT; master->bus_num = -1; -- cgit v1.2.3-70-g09d2 From bafe886936a8982f5780330c901889a37bba7d4c Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sat, 27 Jul 2013 12:34:24 +0100 Subject: spi/tegra-slink: Factor runtime PM out into transfer prepare/unprepare Currently the tegra slink driver acquires a runtime PM reference for the duration of each transfer. This may result in the IP being powered down between transfers which would be at best wasteful. Instead it is better to do this in the callbacks that are generated before and after starting a series of transfers, keeping the IP powered throughout. Signed-off-by: Mark Brown Acked-by: Laxman Dewangan --- drivers/spi/spi-tegra20-slink.c | 32 +++++++++++++++++++++++++------- 1 file changed, 25 insertions(+), 7 deletions(-) diff --git a/drivers/spi/spi-tegra20-slink.c b/drivers/spi/spi-tegra20-slink.c index 80490cc11ce..b2fb115df02 100644 --- a/drivers/spi/spi-tegra20-slink.c +++ b/drivers/spi/spi-tegra20-slink.c @@ -824,6 +824,20 @@ static int tegra_slink_setup(struct spi_device *spi) return 0; } +static int tegra_slink_prepare_transfer(struct spi_master *spi) +{ + struct tegra_slink_data *tspi = spi_master_get_devdata(spi); + int ret; + + ret = pm_runtime_get_sync(tspi->dev); + if (ret < 0) { + dev_err(tspi->dev, "runtime PM get failed: %d\n", ret); + return ret; + } + + return ret; +} + static int tegra_slink_transfer_one_message(struct spi_master *master, struct spi_message *msg) { @@ -836,11 +850,6 @@ static int tegra_slink_transfer_one_message(struct spi_master *master, msg->status = 0; msg->actual_length = 0; - ret = pm_runtime_get_sync(tspi->dev); - if (ret < 0) { - dev_err(tspi->dev, "runtime get failed: %d\n", ret); - goto done; - } single_xfer = list_is_singular(&msg->transfers); list_for_each_entry(xfer, &msg->transfers, transfer_list) { @@ -878,13 +887,20 @@ static int tegra_slink_transfer_one_message(struct spi_master *master, exit: tegra_slink_writel(tspi, tspi->def_command_reg, SLINK_COMMAND); tegra_slink_writel(tspi, tspi->def_command2_reg, SLINK_COMMAND2); - pm_runtime_put(tspi->dev); -done: msg->status = ret; spi_finalize_current_message(master); return ret; } +static int tegra_slink_unprepare_transfer(struct spi_master *spi) +{ + struct tegra_slink_data *tspi = spi_master_get_devdata(spi); + + pm_runtime_put(tspi->dev); + + return 0; +} + static irqreturn_t handle_cpu_based_xfer(struct tegra_slink_data *tspi) { struct spi_transfer *t = tspi->curr_xfer; @@ -1085,7 +1101,9 @@ static int tegra_slink_probe(struct platform_device *pdev) /* the spi->mode bits understood by this driver: */ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; master->setup = tegra_slink_setup; + master->prepare_transfer_hardware = tegra_slink_prepare_transfer; master->transfer_one_message = tegra_slink_transfer_one_message; + master->unprepare_transfer_hardware = tegra_slink_unprepare_transfer; master->num_chipselect = MAX_CHIP_SELECT; master->bus_num = -1; -- cgit v1.2.3-70-g09d2 From 49834de234f3cf592c3d242c889ca603db8e7050 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sun, 28 Jul 2013 14:47:02 +0100 Subject: spi: Provide core support for runtime PM during transfers Most SPI drivers that implement runtime PM support use identical code to do so: they acquire a runtime PM lock in prepare_transfer_hardware() and then they release it in unprepare_transfer_hardware(). The variations in this are mostly missing error checking and the choice to use autosuspend. Since these runtime PM calls are normally the only thing in the prepare and unprepare callbacks and the autosuspend API transparently does the right thing on devices with autosuspend disabled factor all of this out into the core with a flag to enable the behaviour. Signed-off-by: Mark Brown Reviewed-by: Stephen Warren Acked-by: Linus Walleij --- drivers/spi/spi.c | 16 ++++++++++++++++ include/linux/spi/spi.h | 5 +++++ 2 files changed, 21 insertions(+) diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index 978dda2c523..361cced6806 100644 --- a/drivers/spi/spi.c +++ b/drivers/spi/spi.c @@ -553,6 +553,10 @@ static void spi_pump_messages(struct kthread_work *work) master->unprepare_transfer_hardware(master)) dev_err(&master->dev, "failed to unprepare transfer hardware\n"); + if (master->auto_runtime_pm) { + pm_runtime_mark_last_busy(master->dev.parent); + pm_runtime_put_autosuspend(master->dev.parent); + } return; } @@ -572,11 +576,23 @@ static void spi_pump_messages(struct kthread_work *work) master->busy = true; spin_unlock_irqrestore(&master->queue_lock, flags); + if (!was_busy && master->auto_runtime_pm) { + ret = pm_runtime_get_sync(master->dev.parent); + if (ret < 0) { + dev_err(&master->dev, "Failed to power device: %d\n", + ret); + return; + } + } + if (!was_busy && master->prepare_transfer_hardware) { ret = master->prepare_transfer_hardware(master); if (ret) { dev_err(&master->dev, "failed to prepare transfer hardware\n"); + + if (master->auto_runtime_pm) + pm_runtime_put(master->dev.parent); return; } } diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index 28e440be1c0..bf0204c0005 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -254,6 +254,9 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv) * @busy: message pump is busy * @running: message pump is running * @rt: whether this queue is set to run as a realtime task + * @auto_runtime_pm: the core should ensure a runtime PM reference is held + * while the hardware is prepared, using the parent + * device for the spidev * @prepare_transfer_hardware: a message will soon arrive from the queue * so the subsystem requests the driver to prepare the transfer hardware * by issuing this call @@ -374,11 +377,13 @@ struct spi_master { bool busy; bool running; bool rt; + bool auto_runtime_pm; int (*prepare_transfer_hardware)(struct spi_master *master); int (*transfer_one_message)(struct spi_master *master, struct spi_message *mesg); int (*unprepare_transfer_hardware)(struct spi_master *master); + /* gpio chip select */ int *cs_gpios; }; -- cgit v1.2.3-70-g09d2 From 5355d96d6fb56507761f261a23c0831f67fa0e0f Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sun, 28 Jul 2013 15:34:06 +0100 Subject: spi/bcm63xx: Convert to core runtime PM Signed-off-by: Mark Brown --- drivers/spi/spi-bcm63xx.c | 21 +-------------------- 1 file changed, 1 insertion(+), 20 deletions(-) diff --git a/drivers/spi/spi-bcm63xx.c b/drivers/spi/spi-bcm63xx.c index 9fd7a39b802..4ac028d6b2d 100644 --- a/drivers/spi/spi-bcm63xx.c +++ b/drivers/spi/spi-bcm63xx.c @@ -231,24 +231,6 @@ static int bcm63xx_txrx_bufs(struct spi_device *spi, struct spi_transfer *first, return 0; } -static int bcm63xx_spi_prepare_transfer(struct spi_master *master) -{ - struct bcm63xx_spi *bs = spi_master_get_devdata(master); - - pm_runtime_get_sync(&bs->pdev->dev); - - return 0; -} - -static int bcm63xx_spi_unprepare_transfer(struct spi_master *master) -{ - struct bcm63xx_spi *bs = spi_master_get_devdata(master); - - pm_runtime_put(&bs->pdev->dev); - - return 0; -} - static int bcm63xx_spi_transfer_one(struct spi_master *master, struct spi_message *m) { @@ -412,11 +394,10 @@ static int bcm63xx_spi_probe(struct platform_device *pdev) master->bus_num = pdata->bus_num; master->num_chipselect = pdata->num_chipselect; - master->prepare_transfer_hardware = bcm63xx_spi_prepare_transfer; - master->unprepare_transfer_hardware = bcm63xx_spi_unprepare_transfer; master->transfer_one_message = bcm63xx_spi_transfer_one; master->mode_bits = MODEBITS; master->bits_per_word_mask = SPI_BPW_MASK(8); + master->auto_runtime_pm = true; bs->msg_type_shift = pdata->msg_type_shift; bs->msg_ctl_width = pdata->msg_ctl_width; bs->tx_io = (u8 *)(bs->regs + bcm63xx_spireg(SPI_MSG_DATA)); -- cgit v1.2.3-70-g09d2 From 3f36e80ab9325bff1e0d4ab72f0efba679bc212f Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sun, 28 Jul 2013 15:34:21 +0100 Subject: spi/coldfire-qspi: Convert to core runtime PM Signed-off-by: Mark Brown --- drivers/spi/spi-coldfire-qspi.c | 21 +-------------------- 1 file changed, 1 insertion(+), 20 deletions(-) diff --git a/drivers/spi/spi-coldfire-qspi.c b/drivers/spi/spi-coldfire-qspi.c index 0631b9d4a5d..e4265eaf054 100644 --- a/drivers/spi/spi-coldfire-qspi.c +++ b/drivers/spi/spi-coldfire-qspi.c @@ -354,24 +354,6 @@ static int mcfqspi_transfer_one_message(struct spi_master *master, } -static int mcfqspi_prepare_transfer_hw(struct spi_master *master) -{ - struct mcfqspi *mcfqspi = spi_master_get_devdata(master); - - pm_runtime_get_sync(mcfqspi->dev); - - return 0; -} - -static int mcfqspi_unprepare_transfer_hw(struct spi_master *master) -{ - struct mcfqspi *mcfqspi = spi_master_get_devdata(master); - - pm_runtime_put_sync(mcfqspi->dev); - - return 0; -} - static int mcfqspi_setup(struct spi_device *spi) { if (spi->chip_select >= spi->master->num_chipselect) { @@ -473,8 +455,7 @@ static int mcfqspi_probe(struct platform_device *pdev) master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 16); master->setup = mcfqspi_setup; master->transfer_one_message = mcfqspi_transfer_one_message; - master->prepare_transfer_hardware = mcfqspi_prepare_transfer_hw; - master->unprepare_transfer_hardware = mcfqspi_unprepare_transfer_hw; + master->auto_runtime_pm = true; platform_set_drvdata(pdev, master); -- cgit v1.2.3-70-g09d2 From f0278a1a40f895095201b08ff5d0168b8fbd26a5 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sun, 28 Jul 2013 15:34:37 +0100 Subject: spi/omap2: Covert to core runtime PM Signed-off-by: Mark Brown Reviewed-by: Felipe Balbi --- drivers/spi/spi-omap2-mcspi.c | 20 +------------------- 1 file changed, 1 insertion(+), 19 deletions(-) diff --git a/drivers/spi/spi-omap2-mcspi.c b/drivers/spi/spi-omap2-mcspi.c index 5994039758d..973c1cb42c9 100644 --- a/drivers/spi/spi-omap2-mcspi.c +++ b/drivers/spi/spi-omap2-mcspi.c @@ -335,23 +335,6 @@ static void omap2_mcspi_restore_ctx(struct omap2_mcspi *mcspi) __raw_writel(cs->chconf0, cs->base + OMAP2_MCSPI_CHCONF0); } -static int omap2_prepare_transfer(struct spi_master *master) -{ - struct omap2_mcspi *mcspi = spi_master_get_devdata(master); - - pm_runtime_get_sync(mcspi->dev); - return 0; -} - -static int omap2_unprepare_transfer(struct spi_master *master) -{ - struct omap2_mcspi *mcspi = spi_master_get_devdata(master); - - pm_runtime_mark_last_busy(mcspi->dev); - pm_runtime_put_autosuspend(mcspi->dev); - return 0; -} - static int mcspi_wait_for_reg_bit(void __iomem *reg, unsigned long bit) { unsigned long timeout; @@ -1318,8 +1301,7 @@ static int omap2_mcspi_probe(struct platform_device *pdev) master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; master->bits_per_word_mask = SPI_BPW_RANGE_MASK(4, 32); master->setup = omap2_mcspi_setup; - master->prepare_transfer_hardware = omap2_prepare_transfer; - master->unprepare_transfer_hardware = omap2_unprepare_transfer; + master->auto_runtime_pm = true; master->transfer_one_message = omap2_mcspi_transfer_one_message; master->cleanup = omap2_mcspi_cleanup; master->dev.of_node = node; -- cgit v1.2.3-70-g09d2 From 29b6e906a70a47c9cdd7406a8c20ef5098f0b4e8 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sun, 28 Jul 2013 15:35:08 +0100 Subject: spi/pl022: Convert to core runtime PM Signed-off-by: Mark Brown Reviewed-by: Linus Walleij --- drivers/spi/spi-pl022.c | 21 +-------------------- 1 file changed, 1 insertion(+), 20 deletions(-) diff --git a/drivers/spi/spi-pl022.c b/drivers/spi/spi-pl022.c index abef061fb84..07e6db6c810 100644 --- a/drivers/spi/spi-pl022.c +++ b/drivers/spi/spi-pl022.c @@ -1555,18 +1555,6 @@ static int pl022_transfer_one_message(struct spi_master *master, return 0; } -static int pl022_prepare_transfer_hardware(struct spi_master *master) -{ - struct pl022 *pl022 = spi_master_get_devdata(master); - - /* - * Just make sure we have all we need to run the transfer by syncing - * with the runtime PM framework. - */ - pm_runtime_get_sync(&pl022->adev->dev); - return 0; -} - static int pl022_unprepare_transfer_hardware(struct spi_master *master) { struct pl022 *pl022 = spi_master_get_devdata(master); @@ -1575,13 +1563,6 @@ static int pl022_unprepare_transfer_hardware(struct spi_master *master) writew((readw(SSP_CR1(pl022->virtbase)) & (~SSP_CR1_MASK_SSE)), SSP_CR1(pl022->virtbase)); - if (pl022->master_info->autosuspend_delay > 0) { - pm_runtime_mark_last_busy(&pl022->adev->dev); - pm_runtime_put_autosuspend(&pl022->adev->dev); - } else { - pm_runtime_put(&pl022->adev->dev); - } - return 0; } @@ -2139,7 +2120,7 @@ static int pl022_probe(struct amba_device *adev, const struct amba_id *id) master->num_chipselect = num_cs; master->cleanup = pl022_cleanup; master->setup = pl022_setup; - master->prepare_transfer_hardware = pl022_prepare_transfer_hardware; + master->auto_runtime_pm = true; master->transfer_one_message = pl022_transfer_one_message; master->unprepare_transfer_hardware = pl022_unprepare_transfer_hardware; master->rt = platform_info->rt; -- cgit v1.2.3-70-g09d2 From 7dd62787334ac6e0e2a0ef3f20bb1936ac431b04 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sun, 28 Jul 2013 15:35:21 +0100 Subject: spi/pxa2xx: Convert to core runtime PM Signed-off-by: Mark Brown --- drivers/spi/spi-pxa2xx.c | 12 +----------- 1 file changed, 1 insertion(+), 11 deletions(-) diff --git a/drivers/spi/spi-pxa2xx.c b/drivers/spi/spi-pxa2xx.c index f440dcee852..a8c85424eb8 100644 --- a/drivers/spi/spi-pxa2xx.c +++ b/drivers/spi/spi-pxa2xx.c @@ -804,14 +804,6 @@ static int pxa2xx_spi_transfer_one_message(struct spi_master *master, return 0; } -static int pxa2xx_spi_prepare_transfer(struct spi_master *master) -{ - struct driver_data *drv_data = spi_master_get_devdata(master); - - pm_runtime_get_sync(&drv_data->pdev->dev); - return 0; -} - static int pxa2xx_spi_unprepare_transfer(struct spi_master *master) { struct driver_data *drv_data = spi_master_get_devdata(master); @@ -820,8 +812,6 @@ static int pxa2xx_spi_unprepare_transfer(struct spi_master *master) write_SSCR0(read_SSCR0(drv_data->ioaddr) & ~SSCR0_SSE, drv_data->ioaddr); - pm_runtime_mark_last_busy(&drv_data->pdev->dev); - pm_runtime_put_autosuspend(&drv_data->pdev->dev); return 0; } @@ -1134,8 +1124,8 @@ static int pxa2xx_spi_probe(struct platform_device *pdev) master->cleanup = cleanup; master->setup = setup; master->transfer_one_message = pxa2xx_spi_transfer_one_message; - master->prepare_transfer_hardware = pxa2xx_spi_prepare_transfer; master->unprepare_transfer_hardware = pxa2xx_spi_unprepare_transfer; + master->auto_runtime_pm = true; drv_data->ssp_type = ssp->type; drv_data->null_dma_buf = (u32 *)PTR_ALIGN(&drv_data[1], DMA_ALIGNMENT); -- cgit v1.2.3-70-g09d2 From 3e00a09d2fbd64f0ad98e7c8c29dbf9e038fc746 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sun, 28 Jul 2013 15:35:36 +0100 Subject: spi/hspi: Convert to core runtime PM Signed-off-by: Mark Brown --- drivers/spi/spi-sh-hspi.c | 18 +----------------- 1 file changed, 1 insertion(+), 17 deletions(-) diff --git a/drivers/spi/spi-sh-hspi.c b/drivers/spi/spi-sh-hspi.c index 716edf99953..b95d6a9fb80 100644 --- a/drivers/spi/spi-sh-hspi.c +++ b/drivers/spi/spi-sh-hspi.c @@ -99,21 +99,6 @@ static int hspi_status_check_timeout(struct hspi_priv *hspi, u32 mask, u32 val) /* * spi master function */ -static int hspi_prepare_transfer(struct spi_master *master) -{ - struct hspi_priv *hspi = spi_master_get_devdata(master); - - pm_runtime_get_sync(hspi->dev); - return 0; -} - -static int hspi_unprepare_transfer(struct spi_master *master) -{ - struct hspi_priv *hspi = spi_master_get_devdata(master); - - pm_runtime_put_sync(hspi->dev); - return 0; -} #define hspi_hw_cs_enable(hspi) hspi_hw_cs_ctrl(hspi, 0) #define hspi_hw_cs_disable(hspi) hspi_hw_cs_ctrl(hspi, 1) @@ -316,9 +301,8 @@ static int hspi_probe(struct platform_device *pdev) master->setup = hspi_setup; master->cleanup = hspi_cleanup; master->mode_bits = SPI_CPOL | SPI_CPHA; - master->prepare_transfer_hardware = hspi_prepare_transfer; + master->auto_runtime_pm = true; master->transfer_one_message = hspi_transfer_one_message; - master->unprepare_transfer_hardware = hspi_unprepare_transfer; ret = spi_register_master(master); if (ret < 0) { dev_err(&pdev->dev, "spi_register_master error.\n"); -- cgit v1.2.3-70-g09d2 From fc0f81b76a6e5c1f1c5e672420595347d846b2f9 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sun, 28 Jul 2013 15:24:54 +0100 Subject: spi/s3c64xx: Use core for runtime PM Signed-off-by: Mark Brown --- drivers/spi/spi-s3c64xx.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c index 63e2070c6c1..a73d0a3a35d 100644 --- a/drivers/spi/spi-s3c64xx.c +++ b/drivers/spi/spi-s3c64xx.c @@ -356,8 +356,6 @@ static int s3c64xx_spi_prepare_transfer(struct spi_master *spi) while (!is_polling(sdd) && !acquire_dma(sdd)) usleep_range(10000, 11000); - pm_runtime_get_sync(&sdd->pdev->dev); - return 0; } @@ -372,7 +370,6 @@ static int s3c64xx_spi_unprepare_transfer(struct spi_master *spi) sdd->ops->release((enum dma_ch)sdd->tx_dma.ch, &s3c64xx_spi_dma_client); } - pm_runtime_put(&sdd->pdev->dev); return 0; } @@ -1395,6 +1392,7 @@ static int s3c64xx_spi_probe(struct platform_device *pdev) SPI_BPW_MASK(8); /* the spi->mode bits understood by this driver: */ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; + master->auto_runtime_pm = true; sdd->regs = devm_ioremap_resource(&pdev->dev, mem_res); if (IS_ERR(sdd->regs)) { -- cgit v1.2.3-70-g09d2 From 612aa5ced770b7ec02d37dd63fd4c7dd2f6e5f37 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sun, 28 Jul 2013 15:37:31 +0100 Subject: spi/tegra114: Use core runtime PM Signed-off-by: Mark Brown Reviewed-by: Stephen Warren --- drivers/spi/spi-tegra114.c | 26 +------------------------- 1 file changed, 1 insertion(+), 25 deletions(-) diff --git a/drivers/spi/spi-tegra114.c b/drivers/spi/spi-tegra114.c index d85882da853..c14e30c8af2 100644 --- a/drivers/spi/spi-tegra114.c +++ b/drivers/spi/spi-tegra114.c @@ -803,20 +803,6 @@ static int tegra_spi_setup(struct spi_device *spi) return 0; } -static int tegra_spi_prepare_transfer(struct spi_master *spi) -{ - struct tegra_spi_data *tspi = spi_master_get_devdata(spi); - int ret; - - ret = pm_runtime_get_sync(tspi->dev); - if (ret < 0) { - dev_err(tspi->dev, "runtime PM get failed: %d\n", ret); - return ret; - } - - return ret; -} - static int tegra_spi_transfer_one_message(struct spi_master *master, struct spi_message *msg) { @@ -870,15 +856,6 @@ exit: return ret; } -static int tegra_spi_unprepare_transfer(struct spi_master *spi) -{ - struct tegra_spi_data *tspi = spi_master_get_devdata(spi); - - pm_runtime_put(tspi->dev); - - return 0; -} - static irqreturn_t handle_cpu_based_xfer(struct tegra_spi_data *tspi) { struct spi_transfer *t = tspi->curr_xfer; @@ -1064,11 +1041,10 @@ static int tegra_spi_probe(struct platform_device *pdev) /* the spi->mode bits understood by this driver: */ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; master->setup = tegra_spi_setup; - master->prepare_transfer_hardware = tegra_spi_prepare_transfer; master->transfer_one_message = tegra_spi_transfer_one_message; - master->unprepare_transfer_hardware = tegra_spi_unprepare_transfer; master->num_chipselect = MAX_CHIP_SELECT; master->bus_num = -1; + master->auto_runtime_pm = true; tspi->master = master; tspi->dev = &pdev->dev; -- cgit v1.2.3-70-g09d2 From 38315fd48d3de6e9a53b86dfd27684970cd092e9 Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sun, 28 Jul 2013 15:37:46 +0100 Subject: spi/tegra20-sflash: Use core runtime PM Signed-off-by: Mark Brown Reviewed-by: Stephen Warren --- drivers/spi/spi-tegra20-sflash.c | 26 +------------------------- 1 file changed, 1 insertion(+), 25 deletions(-) diff --git a/drivers/spi/spi-tegra20-sflash.c b/drivers/spi/spi-tegra20-sflash.c index f871c4ee6ad..1d814dc6e00 100644 --- a/drivers/spi/spi-tegra20-sflash.c +++ b/drivers/spi/spi-tegra20-sflash.c @@ -325,20 +325,6 @@ static int tegra_sflash_setup(struct spi_device *spi) return 0; } -static int tegra_sflash_prepare_transfer(struct spi_master *spi) -{ - struct tegra_sflash_data *tsd = spi_master_get_devdata(spi); - int ret; - - ret = pm_runtime_get_sync(tsd->dev); - if (ret < 0) { - dev_err(tsd->dev, "runtime PM get failed: %d\n", ret); - return ret; - } - - return ret; -} - static int tegra_sflash_transfer_one_message(struct spi_master *master, struct spi_message *msg) { @@ -391,15 +377,6 @@ exit: return ret; } -static int tegra_sflash_unprepare_transfer(struct spi_master *spi) -{ - struct tegra_sflash_data *tsd = spi_master_get_devdata(spi); - - pm_runtime_put(tsd->dev); - - return 0; -} - static irqreturn_t handle_cpu_based_xfer(struct tegra_sflash_data *tsd) { struct spi_transfer *t = tsd->curr_xfer; @@ -492,9 +469,8 @@ static int tegra_sflash_probe(struct platform_device *pdev) /* the spi->mode bits understood by this driver: */ master->mode_bits = SPI_CPOL | SPI_CPHA; master->setup = tegra_sflash_setup; - master->prepare_transfer_hardware = tegra_sflash_prepare_transfer; master->transfer_one_message = tegra_sflash_transfer_one_message; - master->unprepare_transfer_hardware = tegra_sflash_unprepare_transfer; + master->auto_runtime_pm = true; master->num_chipselect = MAX_CHIP_SELECT; master->bus_num = -1; -- cgit v1.2.3-70-g09d2 From ce74ac80d25bcb1bf5c6638cf376054c9b7c4b0b Mon Sep 17 00:00:00 2001 From: Mark Brown Date: Sun, 28 Jul 2013 15:37:59 +0100 Subject: spi/tegra20-slink: Use core runtime PM Signed-off-by: Mark Brown Reviewed-by: Stephen Warren --- drivers/spi/spi-tegra20-slink.c | 26 +------------------------- 1 file changed, 1 insertion(+), 25 deletions(-) diff --git a/drivers/spi/spi-tegra20-slink.c b/drivers/spi/spi-tegra20-slink.c index b2fb115df02..c70353672a2 100644 --- a/drivers/spi/spi-tegra20-slink.c +++ b/drivers/spi/spi-tegra20-slink.c @@ -824,20 +824,6 @@ static int tegra_slink_setup(struct spi_device *spi) return 0; } -static int tegra_slink_prepare_transfer(struct spi_master *spi) -{ - struct tegra_slink_data *tspi = spi_master_get_devdata(spi); - int ret; - - ret = pm_runtime_get_sync(tspi->dev); - if (ret < 0) { - dev_err(tspi->dev, "runtime PM get failed: %d\n", ret); - return ret; - } - - return ret; -} - static int tegra_slink_transfer_one_message(struct spi_master *master, struct spi_message *msg) { @@ -892,15 +878,6 @@ exit: return ret; } -static int tegra_slink_unprepare_transfer(struct spi_master *spi) -{ - struct tegra_slink_data *tspi = spi_master_get_devdata(spi); - - pm_runtime_put(tspi->dev); - - return 0; -} - static irqreturn_t handle_cpu_based_xfer(struct tegra_slink_data *tspi) { struct spi_transfer *t = tspi->curr_xfer; @@ -1101,9 +1078,8 @@ static int tegra_slink_probe(struct platform_device *pdev) /* the spi->mode bits understood by this driver: */ master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; master->setup = tegra_slink_setup; - master->prepare_transfer_hardware = tegra_slink_prepare_transfer; master->transfer_one_message = tegra_slink_transfer_one_message; - master->unprepare_transfer_hardware = tegra_slink_unprepare_transfer; + master->auto_runtime_pm = true; master->num_chipselect = MAX_CHIP_SELECT; master->bus_num = -1; -- cgit v1.2.3-70-g09d2 From 505a14954e2d7f2321a73f7a650bb6591d2fc1d3 Mon Sep 17 00:00:00 2001 From: Sourav Poddar Date: Tue, 20 Aug 2013 18:55:48 +0530 Subject: spi/qspi: Add qspi flash controller The patch add basic support for the quad spi controller. QSPI is a kind of spi module that allows single, dual and quad read access to external spi devices. The module has a memory mapped interface which provide direct interface for accessing data form external spi devices. The patch will configure controller clocks, device control register and for defining low level transfer apis which will be used by the spi framework to transfer data to the slave spi device(flash in this case). Test details: ------------- Tested this on dra7 board. Test1: Ran mtd_stesstest for 40000 iterations. - All iterations went through without failure. Test2: Use mtd utilities: - flash_erase to erase the flash device - mtd_debug read to read data back. - mtd_debug write to write to the data flash. diff between the write and read data shows zero. Acked-by: Felipe Balbi Reviewed-by: Felipe Balbi Signed-off-by: Sourav Poddar Signed-off-by: Mark Brown --- Documentation/devicetree/bindings/spi/ti_qspi.txt | 22 + drivers/spi/Kconfig | 8 + drivers/spi/Makefile | 1 + drivers/spi/spi-ti-qspi.c | 561 ++++++++++++++++++++++ 4 files changed, 592 insertions(+) create mode 100644 Documentation/devicetree/bindings/spi/ti_qspi.txt create mode 100644 drivers/spi/spi-ti-qspi.c diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt new file mode 100644 index 00000000000..398ef595977 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -0,0 +1,22 @@ +TI QSPI controller. + +Required properties: +- compatible : should be "ti,dra7xxx-qspi". +- reg: Should contain QSPI registers location and length. +- #address-cells, #size-cells : Must be present if the device has sub-nodes +- ti,hwmods: Name of the hwmod associated to the QSPI + +Recommended properties: +- spi-max-frequency: Definition as per + Documentation/devicetree/bindings/spi/spi-bus.txt + +Example: + +qspi: qspi@4b300000 { + compatible = "ti,dra7xxx-qspi"; + reg = <0x4b300000 0x100>; + #address-cells = <1>; + #size-cells = <0>; + spi-max-frequency = <25000000>; + ti,hwmods = "qspi"; +}; diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 89cbbabaff4..72dee132b6c 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -285,6 +285,14 @@ config SPI_OMAP24XX SPI master controller for OMAP24XX and later Multichannel SPI (McSPI) modules. +config SPI_TI_QSPI + tristate "DRA7xxx QSPI controller support" + depends on ARCH_OMAP2PLUS || COMPILE_TEST + help + QSPI master controller for DRA7xxx used for flash devices. + This device supports single, dual and quad read support, while + it only supports single write mode. + config SPI_OMAP_100K tristate "OMAP SPI 100K" depends on ARCH_OMAP850 || ARCH_OMAP730 diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile index 33f9c09561e..a174030a083 100644 --- a/drivers/spi/Makefile +++ b/drivers/spi/Makefile @@ -46,6 +46,7 @@ obj-$(CONFIG_SPI_OCTEON) += spi-octeon.o obj-$(CONFIG_SPI_OMAP_UWIRE) += spi-omap-uwire.o obj-$(CONFIG_SPI_OMAP_100K) += spi-omap-100k.o obj-$(CONFIG_SPI_OMAP24XX) += spi-omap2-mcspi.o +obj-$(CONFIG_SPI_TI_QSPI) += spi-ti-qspi.o obj-$(CONFIG_SPI_ORION) += spi-orion.o obj-$(CONFIG_SPI_PL022) += spi-pl022.o obj-$(CONFIG_SPI_PPC4xx) += spi-ppc4xx.o diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c new file mode 100644 index 00000000000..09e241551fc --- /dev/null +++ b/drivers/spi/spi-ti-qspi.c @@ -0,0 +1,561 @@ +/* + * TI QSPI driver + * + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com + * Author: Sourav Poddar + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GPLv2. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR /PURPOSE. See the + * GNU General Public License for more details. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include + +struct ti_qspi_regs { + u32 clkctrl; +}; + +struct ti_qspi { + struct completion transfer_complete; + + /* IRQ synchronization */ + spinlock_t lock; + + /* list synchronization */ + struct mutex list_lock; + + struct spi_master *master; + void __iomem *base; + struct clk *fclk; + struct device *dev; + + struct ti_qspi_regs ctx_reg; + + u32 spi_max_frequency; + u32 cmd; + u32 dc; + u32 stat; +}; + +#define QSPI_PID (0x0) +#define QSPI_SYSCONFIG (0x10) +#define QSPI_INTR_STATUS_RAW_SET (0x20) +#define QSPI_INTR_STATUS_ENABLED_CLEAR (0x24) +#define QSPI_INTR_ENABLE_SET_REG (0x28) +#define QSPI_INTR_ENABLE_CLEAR_REG (0x2c) +#define QSPI_SPI_CLOCK_CNTRL_REG (0x40) +#define QSPI_SPI_DC_REG (0x44) +#define QSPI_SPI_CMD_REG (0x48) +#define QSPI_SPI_STATUS_REG (0x4c) +#define QSPI_SPI_DATA_REG (0x50) +#define QSPI_SPI_SETUP0_REG (0x54) +#define QSPI_SPI_SWITCH_REG (0x64) +#define QSPI_SPI_SETUP1_REG (0x58) +#define QSPI_SPI_SETUP2_REG (0x5c) +#define QSPI_SPI_SETUP3_REG (0x60) +#define QSPI_SPI_DATA_REG_1 (0x68) +#define QSPI_SPI_DATA_REG_2 (0x6c) +#define QSPI_SPI_DATA_REG_3 (0x70) + +#define QSPI_COMPLETION_TIMEOUT msecs_to_jiffies(2000) + +#define QSPI_FCLK 192000000 + +/* Clock Control */ +#define QSPI_CLK_EN (1 << 31) +#define QSPI_CLK_DIV_MAX 0xffff + +/* Command */ +#define QSPI_EN_CS(n) (n << 28) +#define QSPI_WLEN(n) ((n - 1) << 19) +#define QSPI_3_PIN (1 << 18) +#define QSPI_RD_SNGL (1 << 16) +#define QSPI_WR_SNGL (2 << 16) +#define QSPI_RD_DUAL (3 << 16) +#define QSPI_RD_QUAD (7 << 16) +#define QSPI_INVAL (4 << 16) +#define QSPI_WC_CMD_INT_EN (1 << 14) +#define QSPI_FLEN(n) ((n - 1) << 0) + +/* STATUS REGISTER */ +#define WC 0x02 + +/* INTERRUPT REGISTER */ +#define QSPI_WC_INT_EN (1 << 1) +#define QSPI_WC_INT_DISABLE (1 << 1) + +/* Device Control */ +#define QSPI_DD(m, n) (m << (3 + n * 8)) +#define QSPI_CKPHA(n) (1 << (2 + n * 8)) +#define QSPI_CSPOL(n) (1 << (1 + n * 8)) +#define QSPI_CKPOL(n) (1 << (n * 8)) + +#define QSPI_FRAME 4096 + +#define QSPI_AUTOSUSPEND_TIMEOUT 2000 + +static inline unsigned long ti_qspi_read(struct ti_qspi *qspi, + unsigned long reg) +{ + return readl(qspi->base + reg); +} + +static inline void ti_qspi_write(struct ti_qspi *qspi, + unsigned long val, unsigned long reg) +{ + writel(val, qspi->base + reg); +} + +static int ti_qspi_setup(struct spi_device *spi) +{ + struct ti_qspi *qspi = spi_master_get_devdata(spi->master); + struct ti_qspi_regs *ctx_reg = &qspi->ctx_reg; + int clk_div = 0, ret; + u32 clk_ctrl_reg, clk_rate, clk_mask; + + if (spi->master->busy) { + dev_dbg(qspi->dev, "master busy doing other trasnfers\n"); + return -EBUSY; + } + + if (!qspi->spi_max_frequency) { + dev_err(qspi->dev, "spi max frequency not defined\n"); + return -EINVAL; + } + + clk_rate = clk_get_rate(qspi->fclk); + + clk_div = DIV_ROUND_UP(clk_rate, qspi->spi_max_frequency) - 1; + + if (clk_div < 0) { + dev_dbg(qspi->dev, "clock divider < 0, using /1 divider\n"); + return -EINVAL; + } + + if (clk_div > QSPI_CLK_DIV_MAX) { + dev_dbg(qspi->dev, "clock divider >%d , using /%d divider\n", + QSPI_CLK_DIV_MAX, QSPI_CLK_DIV_MAX + 1); + return -EINVAL; + } + + dev_dbg(qspi->dev, "hz: %d, clock divider %d\n", + qspi->spi_max_frequency, clk_div); + + ret = pm_runtime_get_sync(qspi->dev); + if (ret) { + dev_err(qspi->dev, "pm_runtime_get_sync() failed\n"); + return ret; + } + + clk_ctrl_reg = ti_qspi_read(qspi, QSPI_SPI_CLOCK_CNTRL_REG); + + clk_ctrl_reg &= ~QSPI_CLK_EN; + + /* disable SCLK */ + ti_qspi_write(qspi, clk_ctrl_reg, QSPI_SPI_CLOCK_CNTRL_REG); + + /* enable SCLK */ + clk_mask = QSPI_CLK_EN | clk_div; + ti_qspi_write(qspi, clk_mask, QSPI_SPI_CLOCK_CNTRL_REG); + ctx_reg->clkctrl = clk_mask; + + pm_runtime_mark_last_busy(qspi->dev); + ret = pm_runtime_put_autosuspend(qspi->dev); + if (ret < 0) { + dev_err(qspi->dev, "pm_runtime_put_autosuspend() failed\n"); + return ret; + } + + return 0; +} + +static void ti_qspi_restore_ctx(struct ti_qspi *qspi) +{ + struct ti_qspi_regs *ctx_reg = &qspi->ctx_reg; + + ti_qspi_write(qspi, ctx_reg->clkctrl, QSPI_SPI_CLOCK_CNTRL_REG); +} + +static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t) +{ + int wlen, count, ret; + unsigned int cmd; + const u8 *txbuf; + + txbuf = t->tx_buf; + cmd = qspi->cmd | QSPI_WR_SNGL; + count = t->len; + wlen = t->bits_per_word; + + while (count) { + switch (wlen) { + case 8: + dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %02x\n", + cmd, qspi->dc, *txbuf); + writeb(*txbuf, qspi->base + QSPI_SPI_DATA_REG); + ti_qspi_write(qspi, cmd, QSPI_SPI_CMD_REG); + ret = wait_for_completion_timeout(&qspi->transfer_complete, + QSPI_COMPLETION_TIMEOUT); + if (ret == 0) { + dev_err(qspi->dev, "write timed out\n"); + return -ETIMEDOUT; + } + txbuf += 1; + count -= 1; + break; + case 16: + dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %04x\n", + cmd, qspi->dc, *txbuf); + writew(*((u16 *)txbuf), qspi->base + QSPI_SPI_DATA_REG); + ti_qspi_write(qspi, cmd, QSPI_SPI_CMD_REG); + ret = wait_for_completion_timeout(&qspi->transfer_complete, + QSPI_COMPLETION_TIMEOUT); + if (ret == 0) { + dev_err(qspi->dev, "write timed out\n"); + return -ETIMEDOUT; + } + txbuf += 2; + count -= 2; + break; + case 32: + dev_dbg(qspi->dev, "tx cmd %08x dc %08x data %08x\n", + cmd, qspi->dc, *txbuf); + writel(*((u32 *)txbuf), qspi->base + QSPI_SPI_DATA_REG); + ti_qspi_write(qspi, cmd, QSPI_SPI_CMD_REG); + ret = wait_for_completion_timeout(&qspi->transfer_complete, + QSPI_COMPLETION_TIMEOUT); + if (ret == 0) { + dev_err(qspi->dev, "write timed out\n"); + return -ETIMEDOUT; + } + txbuf += 4; + count -= 4; + break; + } + } + + return 0; +} + +static int qspi_read_msg(struct ti_qspi *qspi, struct spi_transfer *t) +{ + int wlen, count, ret; + unsigned int cmd; + u8 *rxbuf; + + rxbuf = t->rx_buf; + cmd = qspi->cmd | QSPI_RD_SNGL; + count = t->len; + wlen = t->bits_per_word; + + while (count) { + dev_dbg(qspi->dev, "rx cmd %08x dc %08x\n", cmd, qspi->dc); + ti_qspi_write(qspi, cmd, QSPI_SPI_CMD_REG); + ret = wait_for_completion_timeout(&qspi->transfer_complete, + QSPI_COMPLETION_TIMEOUT); + if (ret == 0) { + dev_err(qspi->dev, "read timed out\n"); + return -ETIMEDOUT; + } + switch (wlen) { + case 8: + *rxbuf = readb(qspi->base + QSPI_SPI_DATA_REG); + rxbuf += 1; + count -= 1; + break; + case 16: + *((u16 *)rxbuf) = readw(qspi->base + QSPI_SPI_DATA_REG); + rxbuf += 2; + count -= 2; + break; + case 32: + *((u32 *)rxbuf) = readl(qspi->base + QSPI_SPI_DATA_REG); + rxbuf += 4; + count -= 4; + break; + } + } + + return 0; +} + +static int qspi_transfer_msg(struct ti_qspi *qspi, struct spi_transfer *t) +{ + int ret; + + if (t->tx_buf) { + ret = qspi_write_msg(qspi, t); + if (ret) { + dev_dbg(qspi->dev, "Error while writing\n"); + return ret; + } + } + + if (t->rx_buf) { + ret = qspi_read_msg(qspi, t); + if (ret) { + dev_dbg(qspi->dev, "Error while reading\n"); + return ret; + } + } + + return 0; +} + +static int ti_qspi_start_transfer_one(struct spi_master *master, + struct spi_message *m) +{ + struct ti_qspi *qspi = spi_master_get_devdata(master); + struct spi_device *spi = m->spi; + struct spi_transfer *t; + int status = 0, ret; + int frame_length; + + /* setup device control reg */ + qspi->dc = 0; + + if (spi->mode & SPI_CPHA) + qspi->dc |= QSPI_CKPHA(spi->chip_select); + if (spi->mode & SPI_CPOL) + qspi->dc |= QSPI_CKPOL(spi->chip_select); + if (spi->mode & SPI_CS_HIGH) + qspi->dc |= QSPI_CSPOL(spi->chip_select); + + frame_length = (m->frame_length << 3) / spi->bits_per_word; + + frame_length = clamp(frame_length, 0, QSPI_FRAME); + + /* setup command reg */ + qspi->cmd = 0; + qspi->cmd |= QSPI_EN_CS(spi->chip_select); + qspi->cmd |= QSPI_FLEN(frame_length); + qspi->cmd |= QSPI_WC_CMD_INT_EN; + + ti_qspi_write(qspi, QSPI_WC_INT_EN, QSPI_INTR_ENABLE_SET_REG); + ti_qspi_write(qspi, qspi->dc, QSPI_SPI_DC_REG); + + mutex_lock(&qspi->list_lock); + + list_for_each_entry(t, &m->transfers, transfer_list) { + qspi->cmd |= QSPI_WLEN(t->bits_per_word); + + ret = qspi_transfer_msg(qspi, t); + if (ret) { + dev_dbg(qspi->dev, "transfer message failed\n"); + return -EINVAL; + } + + m->actual_length += t->len; + } + + mutex_unlock(&qspi->list_lock); + + m->status = status; + spi_finalize_current_message(master); + + ti_qspi_write(qspi, qspi->cmd | QSPI_INVAL, QSPI_SPI_CMD_REG); + + return status; +} + +static irqreturn_t ti_qspi_isr(int irq, void *dev_id) +{ + struct ti_qspi *qspi = dev_id; + u16 int_stat; + + irqreturn_t ret = IRQ_HANDLED; + + spin_lock(&qspi->lock); + + int_stat = ti_qspi_read(qspi, QSPI_INTR_STATUS_ENABLED_CLEAR); + qspi->stat = ti_qspi_read(qspi, QSPI_SPI_STATUS_REG); + + if (!int_stat) { + dev_dbg(qspi->dev, "No IRQ triggered\n"); + ret = IRQ_NONE; + goto out; + } + + ret = IRQ_WAKE_THREAD; + + ti_qspi_write(qspi, QSPI_WC_INT_DISABLE, QSPI_INTR_ENABLE_CLEAR_REG); + ti_qspi_write(qspi, QSPI_WC_INT_DISABLE, + QSPI_INTR_STATUS_ENABLED_CLEAR); + +out: + spin_unlock(&qspi->lock); + + return ret; +} + +static irqreturn_t ti_qspi_threaded_isr(int this_irq, void *dev_id) +{ + struct ti_qspi *qspi = dev_id; + unsigned long flags; + + spin_lock_irqsave(&qspi->lock, flags); + + if (qspi->stat & WC) + complete(&qspi->transfer_complete); + + spin_unlock_irqrestore(&qspi->lock, flags); + + ti_qspi_write(qspi, QSPI_WC_INT_EN, QSPI_INTR_ENABLE_SET_REG); + + return IRQ_HANDLED; +} + +static int ti_qspi_runtime_resume(struct device *dev) +{ + struct ti_qspi *qspi; + struct spi_master *master; + + master = dev_get_drvdata(dev); + qspi = spi_master_get_devdata(master); + ti_qspi_restore_ctx(qspi); + + return 0; +} + +static const struct of_device_id ti_qspi_match[] = { + {.compatible = "ti,dra7xxx-qspi" }, + {}, +}; +MODULE_DEVICE_TABLE(of, dra7xxx_qspi_match); + +static int ti_qspi_probe(struct platform_device *pdev) +{ + struct ti_qspi *qspi; + struct spi_master *master; + struct resource *r; + struct device_node *np = pdev->dev.of_node; + u32 max_freq; + int ret = 0, num_cs, irq; + + master = spi_alloc_master(&pdev->dev, sizeof(*qspi)); + if (!master) + return -ENOMEM; + + master->mode_bits = SPI_CPOL | SPI_CPHA; + + master->bus_num = -1; + master->flags = SPI_MASTER_HALF_DUPLEX; + master->setup = ti_qspi_setup; + master->auto_runtime_pm = true; + master->transfer_one_message = ti_qspi_start_transfer_one; + master->dev.of_node = pdev->dev.of_node; + master->bits_per_word_mask = BIT(32 - 1) | BIT(16 - 1) | BIT(8 - 1); + + if (!of_property_read_u32(np, "num-cs", &num_cs)) + master->num_chipselect = num_cs; + + platform_set_drvdata(pdev, master); + + qspi = spi_master_get_devdata(master); + qspi->master = master; + qspi->dev = &pdev->dev; + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + + irq = platform_get_irq(pdev, 0); + if (irq < 0) { + dev_err(&pdev->dev, "no irq resource?\n"); + return irq; + } + + spin_lock_init(&qspi->lock); + mutex_init(&qspi->list_lock); + + qspi->base = devm_ioremap_resource(&pdev->dev, r); + if (IS_ERR(qspi->base)) { + ret = PTR_ERR(qspi->base); + goto free_master; + } + + ret = devm_request_threaded_irq(&pdev->dev, irq, ti_qspi_isr, + ti_qspi_threaded_isr, 0, + dev_name(&pdev->dev), qspi); + if (ret < 0) { + dev_err(&pdev->dev, "Failed to register ISR for IRQ %d\n", + irq); + goto free_master; + } + + qspi->fclk = devm_clk_get(&pdev->dev, "fck"); + if (IS_ERR(qspi->fclk)) { + ret = PTR_ERR(qspi->fclk); + dev_err(&pdev->dev, "could not get clk: %d\n", ret); + } + + init_completion(&qspi->transfer_complete); + + pm_runtime_use_autosuspend(&pdev->dev); + pm_runtime_set_autosuspend_delay(&pdev->dev, QSPI_AUTOSUSPEND_TIMEOUT); + pm_runtime_enable(&pdev->dev); + + if (!of_property_read_u32(np, "spi-max-frequency", &max_freq)) + qspi->spi_max_frequency = max_freq; + + ret = spi_register_master(master); + if (ret) + goto free_master; + + return 0; + +free_master: + spi_master_put(master); + return ret; +} + +static int ti_qspi_remove(struct platform_device *pdev) +{ + struct ti_qspi *qspi = platform_get_drvdata(pdev); + + spi_unregister_master(qspi->master); + + return 0; +} + +static const struct dev_pm_ops ti_qspi_pm_ops = { + .runtime_resume = ti_qspi_runtime_resume, +}; + +static struct platform_driver ti_qspi_driver = { + .probe = ti_qspi_probe, + .remove = ti_qspi_remove, + .driver = { + .name = "ti,dra7xxx-qspi", + .owner = THIS_MODULE, + .pm = &ti_qspi_pm_ops, + .of_match_table = ti_qspi_match, + } +}; + +module_platform_driver(ti_qspi_driver); + +MODULE_AUTHOR("Sourav Poddar "); +MODULE_LICENSE("GPL v2"); +MODULE_DESCRIPTION("TI QSPI controller driver"); -- cgit v1.2.3-70-g09d2 From f477b7fb13df2b843997559ff34e87d054ba6538 Mon Sep 17 00:00:00 2001 From: wangyuhang Date: Sun, 11 Aug 2013 18:15:17 +0800 Subject: spi: DUAL and QUAD support fix the previous patch some mistake below: 1. DT in slave node, use "spi-tx-nbits = <1/2/4>" in place of using "spi-tx-dual, spi-tx-quad" directly, same to rx. So correct the previous way to get the property in @of_register_spi_devices(). 2. Change the value of transfer bit macro(SPI_NBITS_SINGLE, SPI_NBITS_DUAL SPI_NBITS_QUAD) to 0x01, 0x02 and 0x04 to match the actual wires. 3. Add the following check (1)keep the tx_nbits and rx_nbits in spi_transfer is not beyond the single, dual and quad. (2)keep tx_nbits and rx_nbits are contained by @spi_device->mode example: if @spi_device->mode = DUAL, then tx/rx_nbits can not be set to QUAD(SPI_NBITS_QUAD) (3)if "@spi_device->mode & SPI_3WIRE", then tx/rx_nbits should be in single(SPI_NBITS_SINGLE) Signed-off-by: wangyuhang Signed-off-by: Mark Brown --- drivers/spi/spi.c | 96 +++++++++++++++++++++++++++++++++++++++++++++++++ include/linux/spi/spi.h | 22 ++++++++++-- 2 files changed, 116 insertions(+), 2 deletions(-) diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index 2a20c32c827..39d38756e98 100644 --- a/drivers/spi/spi.c +++ b/drivers/spi/spi.c @@ -869,6 +869,51 @@ static void of_register_spi_devices(struct spi_master *master) if (of_find_property(nc, "spi-3wire", NULL)) spi->mode |= SPI_3WIRE; + /* Device DUAL/QUAD mode */ + prop = of_get_property(nc, "spi-tx-nbits", &len); + if (!prop || len < sizeof(*prop)) { + dev_err(&master->dev, "%s has no 'spi-tx-nbits' property\n", + nc->full_name); + spi_dev_put(spi); + continue; + } + switch (be32_to_cpup(prop)) { + case SPI_NBITS_SINGLE: + break; + case SPI_NBITS_DUAL: + spi->mode |= SPI_TX_DUAL; + break; + case SPI_NBITS_QUAD: + spi->mode |= SPI_TX_QUAD; + break; + default: + dev_err(&master->dev, "spi-tx-nbits value is not supported\n"); + spi_dev_put(spi); + continue; + } + + prop = of_get_property(nc, "spi-rx-nbits", &len); + if (!prop || len < sizeof(*prop)) { + dev_err(&master->dev, "%s has no 'spi-rx-nbits' property\n", + nc->full_name); + spi_dev_put(spi); + continue; + } + switch (be32_to_cpup(prop)) { + case SPI_NBITS_SINGLE: + break; + case SPI_NBITS_DUAL: + spi->mode |= SPI_RX_DUAL; + break; + case SPI_NBITS_QUAD: + spi->mode |= SPI_RX_QUAD; + break; + default: + dev_err(&master->dev, "spi-rx-nbits value is not supported\n"); + spi_dev_put(spi); + continue; + } + /* Device speed */ prop = of_get_property(nc, "spi-max-frequency", &len); if (!prop || len < sizeof(*prop)) { @@ -1316,6 +1361,19 @@ int spi_setup(struct spi_device *spi) unsigned bad_bits; int status = 0; + /* check mode to prevent that DUAL and QUAD set at the same time + */ + if (((spi->mode & SPI_TX_DUAL) && (spi->mode & SPI_TX_QUAD)) || + ((spi->mode & SPI_RX_DUAL) && (spi->mode & SPI_RX_QUAD))) { + dev_err(&spi->dev, + "setup: can not select dual and quad at the same time\n"); + return -EINVAL; + } + /* if it is SPI_3WIRE mode, DUAL and QUAD should be forbidden + */ + if ((spi->mode & SPI_3WIRE) && (spi->mode & + (SPI_TX_DUAL | SPI_TX_QUAD | SPI_RX_DUAL | SPI_RX_QUAD))) + return -EINVAL; /* help drivers fail *cleanly* when they need options * that aren't supported with their current master */ @@ -1378,6 +1436,8 @@ static int __spi_async(struct spi_device *spi, struct spi_message *message) /** * Set transfer bits_per_word and max speed as spi device default if * it is not set for this transfer. + * Set transfer tx_nbits and rx_nbits as single transfer default + * (SPI_NBITS_SINGLE) if it is not set for this transfer. */ list_for_each_entry(xfer, &message->transfers, transfer_list) { if (!xfer->bits_per_word) @@ -1403,6 +1463,42 @@ static int __spi_async(struct spi_device *spi, struct spi_message *message) return -EINVAL; if (xfer->speed_hz && master->max_speed_hz && xfer->speed_hz > master->max_speed_hz) + + if (xfer->tx_buf && !xfer->tx_nbits) + xfer->tx_nbits = SPI_NBITS_SINGLE; + if (xfer->rx_buf && !xfer->rx_nbits) + xfer->rx_nbits = SPI_NBITS_SINGLE; + /* check transfer tx/rx_nbits: + * 1. keep the value is not out of single, dual and quad + * 2. keep tx/rx_nbits is contained by mode in spi_device + * 3. if SPI_3WIRE, tx/rx_nbits should be in single + */ + if (xfer->tx_nbits != SPI_NBITS_SINGLE && + xfer->tx_nbits != SPI_NBITS_DUAL && + xfer->tx_nbits != SPI_NBITS_QUAD) + return -EINVAL; + if ((xfer->tx_nbits == SPI_NBITS_DUAL) && + !(spi->mode & (SPI_TX_DUAL | SPI_TX_QUAD))) + return -EINVAL; + if ((xfer->tx_nbits == SPI_NBITS_QUAD) && + !(spi->mode & SPI_TX_QUAD)) + return -EINVAL; + if ((spi->mode & SPI_3WIRE) && + (xfer->tx_nbits != SPI_NBITS_SINGLE)) + return -EINVAL; + /* check transfer rx_nbits */ + if (xfer->rx_nbits != SPI_NBITS_SINGLE && + xfer->rx_nbits != SPI_NBITS_DUAL && + xfer->rx_nbits != SPI_NBITS_QUAD) + return -EINVAL; + if ((xfer->rx_nbits == SPI_NBITS_DUAL) && + !(spi->mode & (SPI_RX_DUAL | SPI_RX_QUAD))) + return -EINVAL; + if ((xfer->rx_nbits == SPI_NBITS_QUAD) && + !(spi->mode & SPI_RX_QUAD)) + return -EINVAL; + if ((spi->mode & SPI_3WIRE) && + (xfer->rx_nbits != SPI_NBITS_SINGLE)) return -EINVAL; } diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index cdf66815615..ccd7840c450 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -74,7 +74,7 @@ struct spi_device { struct spi_master *master; u32 max_speed_hz; u8 chip_select; - u8 mode; + u16 mode; #define SPI_CPHA 0x01 /* clock phase */ #define SPI_CPOL 0x02 /* clock polarity */ #define SPI_MODE_0 (0|0) /* (original MicroWire) */ @@ -87,6 +87,10 @@ struct spi_device { #define SPI_LOOP 0x20 /* loopback mode */ #define SPI_NO_CS 0x40 /* 1 dev/bus, no chipselect */ #define SPI_READY 0x80 /* slave pulls low to pause */ +#define SPI_TX_DUAL 0x100 /* transmit with 2 wires */ +#define SPI_TX_QUAD 0x200 /* transmit with 4 wires */ +#define SPI_RX_DUAL 0x400 /* receive with 2 wires */ +#define SPI_RX_QUAD 0x800 /* receive with 4 wires */ u8 bits_per_word; int irq; void *controller_state; @@ -454,6 +458,10 @@ extern struct spi_master *spi_busnum_to_master(u16 busnum); * @rx_buf: data to be read (dma-safe memory), or NULL * @tx_dma: DMA address of tx_buf, if @spi_message.is_dma_mapped * @rx_dma: DMA address of rx_buf, if @spi_message.is_dma_mapped + * @tx_nbits: number of bits used for writting. If 0 the default + * (SPI_NBITS_SINGLE) is used. + * @rx_nbits: number of bits used for reading. If 0 the default + * (SPI_NBITS_SINGLE) is used. * @len: size of rx and tx buffers (in bytes) * @speed_hz: Select a speed other than the device default for this * transfer. If 0 the default (from @spi_device) is used. @@ -508,6 +516,11 @@ extern struct spi_master *spi_busnum_to_master(u16 busnum); * by the results of previous messages and where the whole transaction * ends when the chipselect goes intactive. * + * When SPI can transfer in 1x,2x or 4x. It can get this tranfer information + * from device through @tx_nbits and @rx_nbits. In Bi-direction, these + * two should both be set. User can set transfer mode with SPI_NBITS_SINGLE(1x) + * SPI_NBITS_DUAL(2x) and SPI_NBITS_QUAD(4x) to support these three transfer. + * * The code that submits an spi_message (and its spi_transfers) * to the lower layers is responsible for managing its memory. * Zero-initialize every field you don't set up explicitly, to @@ -528,6 +541,11 @@ struct spi_transfer { dma_addr_t rx_dma; unsigned cs_change:1; + u8 tx_nbits; + u8 rx_nbits; +#define SPI_NBITS_SINGLE 0x01 /* 1bit transfer */ +#define SPI_NBITS_DUAL 0x02 /* 2bits transfer */ +#define SPI_NBITS_QUAD 0x04 /* 4bits transfer */ u8 bits_per_word; u16 delay_usecs; u32 speed_hz; @@ -875,7 +893,7 @@ struct spi_board_info { /* mode becomes spi_device.mode, and is essential for chips * where the default of SPI_CS_HIGH = 0 is wrong. */ - u8 mode; + u16 mode; /* ... may need additional spi_device chip config data here. * avoid stuff protocol drivers can set; but include stuff -- cgit v1.2.3-70-g09d2 From db90a44177ac39fc22b2da5235b231fccdd4c673 Mon Sep 17 00:00:00 2001 From: Sourav Poddar Date: Thu, 22 Aug 2013 21:20:48 +0530 Subject: spi: conditional checking of mode and transfer bits. There is a bug in the following patch: http://comments.gmane.org/gmane.linux.kernel.spi.devel/14420 spi: DUAL and QUAD support fix the previous patch some mistake below: 1. DT in slave node, use "spi-tx-nbits = <1/2/4>" in place of using "spi-tx-dual, spi-tx-quad" directly, same to rx. So correct the previous way to get the property in @of_register_spi_devices(). 2. Change the value of transfer bit macro(SPI_NBITS_SINGLE, SPI_NBITS_DUAL SPI_NBITS_QUAD) to 0x01, 0x02 and 0x04 to match the actual wires. 3. Add the following check (1)keep the tx_nbits and rx_nbits in spi_transfer is not beyond the single, dual and quad. (2)keep tx_nbits and rx_nbits are contained by @spi_device->mode example: if @spi_device->mode = DUAL, then tx/rx_nbits can not be set to QUAD(SPI_NBITS_QUAD) (3)if "@spi_device->mode & SPI_3WIRE", then tx/rx_nbits should be in single(SPI_NBITS_SINGLE) Checking of the tx/rx transfer bits and mode bits should be done conditionally based on type of buffer filled else EINVAL condition will always get hit either for rx or tx. Signed-off-by: Sourav Poddar Signed-off-by: Mark Brown --- drivers/spi/spi.c | 56 +++++++++++++++++++++++++++++-------------------------- 1 file changed, 30 insertions(+), 26 deletions(-) diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index 39d38756e98..50f7fc3ed79 100644 --- a/drivers/spi/spi.c +++ b/drivers/spi/spi.c @@ -1473,33 +1473,37 @@ static int __spi_async(struct spi_device *spi, struct spi_message *message) * 2. keep tx/rx_nbits is contained by mode in spi_device * 3. if SPI_3WIRE, tx/rx_nbits should be in single */ - if (xfer->tx_nbits != SPI_NBITS_SINGLE && - xfer->tx_nbits != SPI_NBITS_DUAL && - xfer->tx_nbits != SPI_NBITS_QUAD) - return -EINVAL; - if ((xfer->tx_nbits == SPI_NBITS_DUAL) && - !(spi->mode & (SPI_TX_DUAL | SPI_TX_QUAD))) - return -EINVAL; - if ((xfer->tx_nbits == SPI_NBITS_QUAD) && - !(spi->mode & SPI_TX_QUAD)) - return -EINVAL; - if ((spi->mode & SPI_3WIRE) && - (xfer->tx_nbits != SPI_NBITS_SINGLE)) - return -EINVAL; + if (xfer->tx_buf) { + if (xfer->tx_nbits != SPI_NBITS_SINGLE && + xfer->tx_nbits != SPI_NBITS_DUAL && + xfer->tx_nbits != SPI_NBITS_QUAD) + return -EINVAL; + if ((xfer->tx_nbits == SPI_NBITS_DUAL) && + !(spi->mode & (SPI_TX_DUAL | SPI_TX_QUAD))) + return -EINVAL; + if ((xfer->tx_nbits == SPI_NBITS_QUAD) && + !(spi->mode & SPI_TX_QUAD)) + return -EINVAL; + if ((spi->mode & SPI_3WIRE) && + (xfer->tx_nbits != SPI_NBITS_SINGLE)) + return -EINVAL; + } /* check transfer rx_nbits */ - if (xfer->rx_nbits != SPI_NBITS_SINGLE && - xfer->rx_nbits != SPI_NBITS_DUAL && - xfer->rx_nbits != SPI_NBITS_QUAD) - return -EINVAL; - if ((xfer->rx_nbits == SPI_NBITS_DUAL) && - !(spi->mode & (SPI_RX_DUAL | SPI_RX_QUAD))) - return -EINVAL; - if ((xfer->rx_nbits == SPI_NBITS_QUAD) && - !(spi->mode & SPI_RX_QUAD)) - return -EINVAL; - if ((spi->mode & SPI_3WIRE) && - (xfer->rx_nbits != SPI_NBITS_SINGLE)) - return -EINVAL; + if (xfer->rx_buf) { + if (xfer->rx_nbits != SPI_NBITS_SINGLE && + xfer->rx_nbits != SPI_NBITS_DUAL && + xfer->rx_nbits != SPI_NBITS_QUAD) + return -EINVAL; + if ((xfer->rx_nbits == SPI_NBITS_DUAL) && + !(spi->mode & (SPI_RX_DUAL | SPI_RX_QUAD))) + return -EINVAL; + if ((xfer->rx_nbits == SPI_NBITS_QUAD) && + !(spi->mode & SPI_RX_QUAD)) + return -EINVAL; + if ((spi->mode & SPI_3WIRE) && + (xfer->rx_nbits != SPI_NBITS_SINGLE)) + return -EINVAL; + } } message->spi = spi; -- cgit v1.2.3-70-g09d2 From 70e2e9761a580cc9ef84be69dac2279dd6c2c72f Mon Sep 17 00:00:00 2001 From: Sourav Poddar Date: Fri, 23 Aug 2013 15:12:16 +0530 Subject: spi/qspi: Add dual/quad spi read support Support for multiple lines in SPI framework has been picked[1]. [1]: http://comments.gmane.org/gmane.linux.kernel.spi.devel/14420 Hence, adapting ti qspi driver to support multiple data lines for read. Signed-off-by: Sourav Poddar Signed-off-by: Mark Brown --- drivers/spi/spi-ti-qspi.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c index 09e241551fc..c07e04170b9 100644 --- a/drivers/spi/spi-ti-qspi.c +++ b/drivers/spi/spi-ti-qspi.c @@ -267,7 +267,18 @@ static int qspi_read_msg(struct ti_qspi *qspi, struct spi_transfer *t) u8 *rxbuf; rxbuf = t->rx_buf; - cmd = qspi->cmd | QSPI_RD_SNGL; + cmd = qspi->cmd; + switch (t->rx_nbits) { + case SPI_NBITS_DUAL: + cmd |= QSPI_RD_DUAL; + break; + case SPI_NBITS_QUAD: + cmd |= QSPI_RD_QUAD; + break; + default: + cmd |= QSPI_RD_SNGL; + break; + } count = t->len; wlen = t->bits_per_word; -- cgit v1.2.3-70-g09d2 From e1432d30cb245f562d495043a58476e7c3b4358e Mon Sep 17 00:00:00 2001 From: Sourav Poddar Date: Tue, 27 Aug 2013 12:41:20 +0530 Subject: spi/qspi: Fix device table entry Fix module device table entry. Without this, there will be a build failure while trying to build qspi as a module. Signed-off-by: Sourav Poddar Signed-off-by: Mark Brown --- drivers/spi/spi-ti-qspi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c index c07e04170b9..79081d9b321 100644 --- a/drivers/spi/spi-ti-qspi.c +++ b/drivers/spi/spi-ti-qspi.c @@ -455,7 +455,7 @@ static const struct of_device_id ti_qspi_match[] = { {.compatible = "ti,dra7xxx-qspi" }, {}, }; -MODULE_DEVICE_TABLE(of, dra7xxx_qspi_match); +MODULE_DEVICE_TABLE(of, ti_qspi_match); static int ti_qspi_probe(struct platform_device *pdev) { -- cgit v1.2.3-70-g09d2 From 09222fc33f8e22e81d34a7518e6dd120e4128a11 Mon Sep 17 00:00:00 2001 From: Sourav Poddar Date: Tue, 27 Aug 2013 19:42:24 +0530 Subject: spi/qspi: Add compatible string for am4372. Add a compatible string for am4372. Signed-off-by: Sourav Poddar Signed-off-by: Mark Brown --- Documentation/devicetree/bindings/spi/ti_qspi.txt | 2 +- drivers/spi/spi-ti-qspi.c | 1 + 2 files changed, 2 insertions(+), 1 deletion(-) diff --git a/Documentation/devicetree/bindings/spi/ti_qspi.txt b/Documentation/devicetree/bindings/spi/ti_qspi.txt index 398ef595977..1f9641ade0b 100644 --- a/Documentation/devicetree/bindings/spi/ti_qspi.txt +++ b/Documentation/devicetree/bindings/spi/ti_qspi.txt @@ -1,7 +1,7 @@ TI QSPI controller. Required properties: -- compatible : should be "ti,dra7xxx-qspi". +- compatible : should be "ti,dra7xxx-qspi" or "ti,am4372-qspi". - reg: Should contain QSPI registers location and length. - #address-cells, #size-cells : Must be present if the device has sub-nodes - ti,hwmods: Name of the hwmod associated to the QSPI diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c index 79081d9b321..136d71eb6f2 100644 --- a/drivers/spi/spi-ti-qspi.c +++ b/drivers/spi/spi-ti-qspi.c @@ -453,6 +453,7 @@ static int ti_qspi_runtime_resume(struct device *dev) static const struct of_device_id ti_qspi_match[] = { {.compatible = "ti,dra7xxx-qspi" }, + {.compatible = "ti,am4372-qspi" }, {}, }; MODULE_DEVICE_TABLE(of, ti_qspi_match); -- cgit v1.2.3-70-g09d2 From b6460366fbadc160604f50047d0394c7fc39ceab Mon Sep 17 00:00:00 2001 From: Wei Yongjun Date: Sun, 1 Sep 2013 09:01:00 +0800 Subject: spi/qspi: fix missing unlock on error in ti_qspi_start_transfer_one() Add the missing unlock before return from function ti_qspi_start_transfer_one() in the error handling case. Signed-off-by: Wei Yongjun Signed-off-by: Mark Brown --- drivers/spi/spi-ti-qspi.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c index 136d71eb6f2..e12d962a289 100644 --- a/drivers/spi/spi-ti-qspi.c +++ b/drivers/spi/spi-ti-qspi.c @@ -376,6 +376,7 @@ static int ti_qspi_start_transfer_one(struct spi_master *master, ret = qspi_transfer_msg(qspi, t); if (ret) { dev_dbg(qspi->dev, "transfer message failed\n"); + mutex_unlock(&qspi->list_lock); return -EINVAL; } -- cgit v1.2.3-70-g09d2