From 8c03356a559ced6fa78931f498193f776d67e445 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Thu, 9 Nov 2006 14:42:16 -0500 Subject: EHCI: Fix root-hub and port suspend/resume problems This patch (as738b) fixes numerous problems in the controller/root-hub suspend/resume/remote-wakeup support in ehci-hcd: The bus_resume() routine should wake up only the ports that were suspended by bus_suspend(). Ports that were already suspended should remain that way. The interrupt mask is used to detect loss of power in the bus_resume() routine (if the mask is 0 then power was lost). However bus_suspend() always sets the mask to 0. Instead the mask should retain its normal value, with port-change-detect interrupts disabled if remote wakeup is turned off. The interrupt mask should be reset to its correct value at the end of bus_resume() regardless of whether power was lost. bus_resume() reinitializes the operational registers if power was lost. However those registers are not in the aux power well, hence they can lose their values whenever the controller is put into D3. They should always be reinitialized. When a port-change interrupt occurs and the root hub is suspended, the interrupt handler should request a root-hub resume instead of starting up the controller all by itself. There's no need for the interrupt handler to request a root-hub resume every time a suspended port sends a remote-wakeup request. The pci_resume() method doesn't need to check for connected ports when deciding whether or not to reset the controller. It can make that decision based on whether Vaux power was maintained. Even when the controller does not need to be reset, pci_resume() must undo the effect of pci_suspend() by re-enabling the interrupt mask. If power was lost, pci_resume() must not call ehci_run(). At this point the root hub is still supposed to be suspended, not running. It's enough to rewrite the command register and set the configured_flag. Signed-off-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-hcd.c | 6 ++-- drivers/usb/host/ehci-hub.c | 67 ++++++++++++++++++++++++++++----------------- drivers/usb/host/ehci-pci.c | 40 +++++++++++---------------- drivers/usb/host/ehci.h | 1 + 4 files changed, 61 insertions(+), 53 deletions(-) diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index f2ceb5fdbeb..025d3331368 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -619,9 +619,8 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd) unsigned i = HCS_N_PORTS (ehci->hcs_params); /* resume root hub? */ - status = readl (&ehci->regs->command); - if (!(status & CMD_RUN)) - writel (status | CMD_RUN, &ehci->regs->command); + if (!(readl(&ehci->regs->command) & CMD_RUN)) + usb_hcd_resume_root_hub(hcd); while (i--) { int pstatus = readl (&ehci->regs->port_status [i]); @@ -638,7 +637,6 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd) */ ehci->reset_done [i] = jiffies + msecs_to_jiffies (20); ehci_dbg (ehci, "port %d remote wakeup\n", i + 1); - usb_hcd_resume_root_hub(hcd); } } diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c index 0a56dfa2745..bfe5f307cba 100644 --- a/drivers/usb/host/ehci-hub.c +++ b/drivers/usb/host/ehci-hub.c @@ -34,6 +34,7 @@ static int ehci_bus_suspend (struct usb_hcd *hcd) { struct ehci_hcd *ehci = hcd_to_ehci (hcd); int port; + int mask; if (time_before (jiffies, ehci->next_statechange)) msleep(5); @@ -51,14 +52,25 @@ static int ehci_bus_suspend (struct usb_hcd *hcd) ehci->reclaim_ready = 1; ehci_work(ehci); - /* suspend any active/unsuspended ports, maybe allow wakeup */ + /* Unlike other USB host controller types, EHCI doesn't have + * any notion of "global" or bus-wide suspend. The driver has + * to manually suspend all the active unsuspended ports, and + * then manually resume them in the bus_resume() routine. + */ + ehci->bus_suspended = 0; while (port--) { u32 __iomem *reg = &ehci->regs->port_status [port]; u32 t1 = readl (reg) & ~PORT_RWC_BITS; u32 t2 = t1; - if ((t1 & PORT_PE) && !(t1 & PORT_OWNER)) + /* keep track of which ports we suspend */ + if ((t1 & PORT_PE) && !(t1 & PORT_OWNER) && + !(t1 & PORT_SUSPEND)) { t2 |= PORT_SUSPEND; + set_bit(port, &ehci->bus_suspended); + } + + /* enable remote wakeup on all ports */ if (device_may_wakeup(&hcd->self.root_hub->dev)) t2 |= PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E; else @@ -76,6 +88,13 @@ static int ehci_bus_suspend (struct usb_hcd *hcd) ehci_halt (ehci); hcd->state = HC_STATE_SUSPENDED; + /* allow remote wakeup */ + mask = INTR_MASK; + if (!device_may_wakeup(&hcd->self.root_hub->dev)) + mask &= ~STS_PCD; + writel(mask, &ehci->regs->intr_enable); + readl(&ehci->regs->intr_enable); + ehci->next_statechange = jiffies + msecs_to_jiffies(10); spin_unlock_irq (&ehci->lock); return 0; @@ -88,7 +107,6 @@ static int ehci_bus_resume (struct usb_hcd *hcd) struct ehci_hcd *ehci = hcd_to_ehci (hcd); u32 temp; int i; - int intr_enable; if (time_before (jiffies, ehci->next_statechange)) msleep(5); @@ -100,31 +118,30 @@ static int ehci_bus_resume (struct usb_hcd *hcd) * the last user of the controller, not reset/pm hardware keeping * state we gave to it. */ + temp = readl(&ehci->regs->intr_enable); + ehci_dbg(ehci, "resume root hub%s\n", temp ? "" : " after power loss"); - /* re-init operational registers in case we lost power */ - if (readl (&ehci->regs->intr_enable) == 0) { - /* at least some APM implementations will try to deliver - * IRQs right away, so delay them until we're ready. - */ - intr_enable = 1; - writel (0, &ehci->regs->segment); - writel (ehci->periodic_dma, &ehci->regs->frame_list); - writel ((u32)ehci->async->qh_dma, &ehci->regs->async_next); - } else - intr_enable = 0; - ehci_dbg(ehci, "resume root hub%s\n", - intr_enable ? " after power loss" : ""); + /* at least some APM implementations will try to deliver + * IRQs right away, so delay them until we're ready. + */ + writel(0, &ehci->regs->intr_enable); + + /* re-init operational registers */ + writel(0, &ehci->regs->segment); + writel(ehci->periodic_dma, &ehci->regs->frame_list); + writel((u32) ehci->async->qh_dma, &ehci->regs->async_next); /* restore CMD_RUN, framelist size, and irq threshold */ writel (ehci->command, &ehci->regs->command); - /* take ports out of suspend */ + /* manually resume the ports we suspended during bus_suspend() */ i = HCS_N_PORTS (ehci->hcs_params); while (i--) { temp = readl (&ehci->regs->port_status [i]); temp &= ~(PORT_RWC_BITS | PORT_WKOC_E | PORT_WKDISC_E | PORT_WKCONN_E); - if (temp & PORT_SUSPEND) { + if (test_bit(i, &ehci->bus_suspended) && + (temp & PORT_SUSPEND)) { ehci->reset_done [i] = jiffies + msecs_to_jiffies (20); temp |= PORT_RESUME; } @@ -134,11 +151,12 @@ static int ehci_bus_resume (struct usb_hcd *hcd) mdelay (20); while (i--) { temp = readl (&ehci->regs->port_status [i]); - if ((temp & PORT_SUSPEND) == 0) - continue; - temp &= ~(PORT_RWC_BITS | PORT_RESUME); - writel (temp, &ehci->regs->port_status [i]); - ehci_vdbg (ehci, "resumed port %d\n", i + 1); + if (test_bit(i, &ehci->bus_suspended) && + (temp & PORT_SUSPEND)) { + temp &= ~(PORT_RWC_BITS | PORT_RESUME); + writel (temp, &ehci->regs->port_status [i]); + ehci_vdbg (ehci, "resumed port %d\n", i + 1); + } } (void) readl (&ehci->regs->command); @@ -157,8 +175,7 @@ static int ehci_bus_resume (struct usb_hcd *hcd) hcd->state = HC_STATE_RUNNING; /* Now we can safely re-enable irqs */ - if (intr_enable) - writel (INTR_MASK, &ehci->regs->intr_enable); + writel(INTR_MASK, &ehci->regs->intr_enable); spin_unlock_irq (&ehci->lock); return 0; diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c index e51c1ed81ac..4bc7970ba3e 100644 --- a/drivers/usb/host/ehci-pci.c +++ b/drivers/usb/host/ehci-pci.c @@ -257,9 +257,7 @@ static int ehci_pci_suspend(struct usb_hcd *hcd, pm_message_t message) static int ehci_pci_resume(struct usb_hcd *hcd) { struct ehci_hcd *ehci = hcd_to_ehci(hcd); - unsigned port; struct pci_dev *pdev = to_pci_dev(hcd->self.controller); - int retval = -EINVAL; // maybe restore FLADJ @@ -269,27 +267,19 @@ static int ehci_pci_resume(struct usb_hcd *hcd) /* Mark hardware accessible again as we are out of D3 state by now */ set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); - /* If CF is clear, we lost PCI Vaux power and need to restart. */ - if (readl(&ehci->regs->configured_flag) != FLAG_CF) - goto restart; - - /* If any port is suspended (or owned by the companion), - * we know we can/must resume the HC (and mustn't reset it). - * We just defer that to the root hub code. + /* If CF is still set, we maintained PCI Vaux power. + * Just undo the effect of ehci_pci_suspend(). */ - for (port = HCS_N_PORTS(ehci->hcs_params); port > 0; ) { - u32 status; - port--; - status = readl(&ehci->regs->port_status [port]); - if (!(status & PORT_POWER)) - continue; - if (status & (PORT_SUSPEND | PORT_RESUME | PORT_OWNER)) { - usb_hcd_resume_root_hub(hcd); - return 0; - } + if (readl(&ehci->regs->configured_flag) == FLAG_CF) { + int mask = INTR_MASK; + + if (!device_may_wakeup(&hcd->self.root_hub->dev)) + mask &= ~STS_PCD; + writel(mask, &ehci->regs->intr_enable); + readl(&ehci->regs->intr_enable); + return 0; } -restart: ehci_dbg(ehci, "lost power, restarting\n"); usb_root_hub_lost_power(hcd->self.root_hub); @@ -307,13 +297,15 @@ restart: ehci_work(ehci); spin_unlock_irq(&ehci->lock); - /* restart; khubd will disconnect devices */ - retval = ehci_run(hcd); - /* here we "know" root ports should always stay powered */ ehci_port_power(ehci, 1); - return retval; + writel(ehci->command, &ehci->regs->command); + writel(FLAG_CF, &ehci->regs->configured_flag); + readl(&ehci->regs->command); /* unblock posted writes */ + + hcd->state = HC_STATE_SUSPENDED; + return 0; } #endif diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h index bbc3082a73d..74dbc6c8228 100644 --- a/drivers/usb/host/ehci.h +++ b/drivers/usb/host/ehci.h @@ -74,6 +74,7 @@ struct ehci_hcd { /* one per controller */ /* per root hub port */ unsigned long reset_done [EHCI_MAX_ROOT_PORTS]; + unsigned long bus_suspended; /* per-HC memory pools (could be per-bus, but ...) */ struct dma_pool *qh_pool; /* qh per active urb */ -- cgit v1.2.3-70-g09d2