From c3d68d8dd4f8d44579e2f0d121990f288c4a0e9a Mon Sep 17 00:00:00 2001 From: Hongbo Zhang Date: Thu, 26 Sep 2013 17:33:41 +0800 Subject: DMA: Freescale: revise device tree binding document This patch updates the discription of each type of DMA controller and its channels, it is preparation for adding another new DMA controller binding, it also fixes some defects of indent for text alignment at the same time. Signed-off-by: Hongbo Zhang Acked-by: Mark Rutland Signed-off-by: Vinod Koul --- .../devicetree/bindings/powerpc/fsl/dma.txt | 68 ++++++++++------------ 1 file changed, 31 insertions(+), 37 deletions(-) (limited to 'Documentation/devicetree/bindings/powerpc/fsl/dma.txt') diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt index 2a4b4bce611..05841689c4a 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt @@ -1,33 +1,30 @@ -* Freescale 83xx DMA Controller +* Freescale DMA Controllers -Freescale PowerPC 83xx have on chip general purpose DMA controllers. +** Freescale Elo DMA Controller + This is a little-endian 4-channel DMA controller, used in Freescale mpc83xx + series chips such as mpc8315, mpc8349, mpc8379 etc. Required properties: -- compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma", where CHIP is the processor - (mpc8349, mpc8360, etc.) and the second is - "fsl,elo-dma" -- reg : -- ranges : Should be defined as specified in 1) to describe the - DMA controller channels. +- compatible : must include "fsl,elo-dma" +- reg : DMA General Status Register, i.e. DGSR which contains + status for all the 4 DMA channels +- ranges : describes the mapping between the address space of the + DMA channels and the address space of the DMA controller - cell-index : controller index. 0 for controller @ 0x8100 -- interrupts : +- interrupts : interrupt specifier for DMA IRQ - interrupt-parent : optional, if needed for interrupt mapping - - DMA channel nodes: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma-channel", where CHIP is the processor - (mpc8349, mpc8350, etc.) and the second is - "fsl,elo-dma-channel". However, see note below. - - reg : - - cell-index : dma channel index starts at 0. + - compatible : must include "fsl,elo-dma-channel" + However, see note below. + - reg : DMA channel specific registers + - cell-index : DMA channel index starts at 0. Optional properties: - - interrupts : - (on 83xx this is expected to be identical to - the interrupts property of the parent node) + - interrupts : interrupt specifier for DMA channel IRQ + (on 83xx this is expected to be identical to + the interrupts property of the parent node) - interrupt-parent : optional, if needed for interrupt mapping Example: @@ -70,30 +67,27 @@ Example: }; }; -* Freescale 85xx/86xx DMA Controller - -Freescale PowerPC 85xx/86xx have on chip general purpose DMA controllers. +** Freescale EloPlus DMA Controller + This is a 4-channel DMA controller with extended addresses and chaining, + mainly used in Freescale mpc85xx/86xx, Pxxx and BSC series chips, such as + mpc8540, mpc8641 p4080, bsc9131 etc. Required properties: -- compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma", where CHIP is the processor - (mpc8540, mpc8540, etc.) and the second is - "fsl,eloplus-dma" -- reg : +- compatible : must include "fsl,eloplus-dma" +- reg : DMA General Status Register, i.e. DGSR which contains + status for all the 4 DMA channels - cell-index : controller index. 0 for controller @ 0x21000, 1 for controller @ 0xc000 -- ranges : Should be defined as specified in 1) to describe the - DMA controller channels. +- ranges : describes the mapping between the address space of the + DMA channels and the address space of the DMA controller - DMA channel nodes: - - compatible : compatible list, contains 2 entries, first is - "fsl,CHIP-dma-channel", where CHIP is the processor - (mpc8540, mpc8560, etc.) and the second is - "fsl,eloplus-dma-channel". However, see note below. - - cell-index : dma channel index starts at 0. - - reg : - - interrupts : + - compatible : must include "fsl,eloplus-dma-channel" + However, see note below. + - cell-index : DMA channel index starts at 0. + - reg : DMA channel specific registers + - interrupts : interrupt specifier for DMA channel IRQ - interrupt-parent : optional, if needed for interrupt mapping Example: -- cgit v1.2.3-70-g09d2 From 03aa254f1e3c3d902cd68763f8abc2387e82b4da Mon Sep 17 00:00:00 2001 From: Hongbo Zhang Date: Thu, 26 Sep 2013 17:33:42 +0800 Subject: DMA: Freescale: Add new 8-channel DMA engine device tree nodes Freescale QorIQ T4 and B4 introduce new 8-channel DMA engines, this patch adds the device tree nodes for them. Signed-off-by: Hongbo Zhang Acked-by: Mark Rutland Signed-off-by: Vinod Koul --- .../devicetree/bindings/powerpc/fsl/dma.txt | 70 ++++++++++++++++++ arch/powerpc/boot/dts/fsl/b4si-post.dtsi | 4 +- arch/powerpc/boot/dts/fsl/elo3-dma-0.dtsi | 82 ++++++++++++++++++++++ arch/powerpc/boot/dts/fsl/elo3-dma-1.dtsi | 82 ++++++++++++++++++++++ arch/powerpc/boot/dts/fsl/t4240si-post.dtsi | 4 +- 5 files changed, 238 insertions(+), 4 deletions(-) create mode 100644 arch/powerpc/boot/dts/fsl/elo3-dma-0.dtsi create mode 100644 arch/powerpc/boot/dts/fsl/elo3-dma-1.dtsi (limited to 'Documentation/devicetree/bindings/powerpc/fsl/dma.txt') diff --git a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt index 05841689c4a..7fc1b010fa7 100644 --- a/Documentation/devicetree/bindings/powerpc/fsl/dma.txt +++ b/Documentation/devicetree/bindings/powerpc/fsl/dma.txt @@ -128,6 +128,76 @@ Example: }; }; +** Freescale Elo3 DMA Controller + DMA controller which has same function as EloPlus except that Elo3 has 8 + channels while EloPlus has only 4, it is used in Freescale Txxx and Bxxx + series chips, such as t1040, t4240, b4860. + +Required properties: + +- compatible : must include "fsl,elo3-dma" +- reg : contains two entries for DMA General Status Registers, + i.e. DGSR0 which includes status for channel 1~4, and + DGSR1 for channel 5~8 +- ranges : describes the mapping between the address space of the + DMA channels and the address space of the DMA controller + +- DMA channel nodes: + - compatible : must include "fsl,eloplus-dma-channel" + - reg : DMA channel specific registers + - interrupts : interrupt specifier for DMA channel IRQ + - interrupt-parent : optional, if needed for interrupt mapping + +Example: +dma@100300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,elo3-dma"; + reg = <0x100300 0x4>, + <0x100600 0x4>; + ranges = <0x0 0x100100 0x500>; + dma-channel@0 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + interrupts = <28 2 0 0>; + }; + dma-channel@80 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + interrupts = <29 2 0 0>; + }; + dma-channel@100 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + interrupts = <30 2 0 0>; + }; + dma-channel@180 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + interrupts = <31 2 0 0>; + }; + dma-channel@300 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x300 0x80>; + interrupts = <76 2 0 0>; + }; + dma-channel@380 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x380 0x80>; + interrupts = <77 2 0 0>; + }; + dma-channel@400 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x400 0x80>; + interrupts = <78 2 0 0>; + }; + dma-channel@480 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x480 0x80>; + interrupts = <79 2 0 0>; + }; +}; + Note on DMA channel compatible properties: The compatible property must say "fsl,elo-dma-channel" or "fsl,eloplus-dma-channel" to be used by the Elo DMA driver (fsldma). Any DMA channel used by fsldma cannot be used by another diff --git a/arch/powerpc/boot/dts/fsl/b4si-post.dtsi b/arch/powerpc/boot/dts/fsl/b4si-post.dtsi index 4c617bf8cdb..4f6e48277c4 100644 --- a/arch/powerpc/boot/dts/fsl/b4si-post.dtsi +++ b/arch/powerpc/boot/dts/fsl/b4si-post.dtsi @@ -223,13 +223,13 @@ reg = <0xe2000 0x1000>; }; -/include/ "qoriq-dma-0.dtsi" +/include/ "elo3-dma-0.dtsi" dma@100300 { fsl,iommu-parent = <&pamu0>; fsl,liodn-reg = <&guts 0x580>; /* DMA1LIODNR */ }; -/include/ "qoriq-dma-1.dtsi" +/include/ "elo3-dma-1.dtsi" dma@101300 { fsl,iommu-parent = <&pamu0>; fsl,liodn-reg = <&guts 0x584>; /* DMA2LIODNR */ diff --git a/arch/powerpc/boot/dts/fsl/elo3-dma-0.dtsi b/arch/powerpc/boot/dts/fsl/elo3-dma-0.dtsi new file mode 100644 index 00000000000..3c210e0d520 --- /dev/null +++ b/arch/powerpc/boot/dts/fsl/elo3-dma-0.dtsi @@ -0,0 +1,82 @@ +/* + * QorIQ Elo3 DMA device tree stub [ controller @ offset 0x100000 ] + * + * Copyright 2013 Freescale Semiconductor Inc. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * * Neither the name of Freescale Semiconductor nor the + * names of its contributors may be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * + * ALTERNATIVELY, this software may be distributed under the terms of the + * GNU General Public License ("GPL") as published by the Free Software + * Foundation, either version 2 of that License or (at your option) any + * later version. + * + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +dma0: dma@100300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,elo3-dma"; + reg = <0x100300 0x4>, + <0x100600 0x4>; + ranges = <0x0 0x100100 0x500>; + dma-channel@0 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + interrupts = <28 2 0 0>; + }; + dma-channel@80 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + interrupts = <29 2 0 0>; + }; + dma-channel@100 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + interrupts = <30 2 0 0>; + }; + dma-channel@180 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + interrupts = <31 2 0 0>; + }; + dma-channel@300 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x300 0x80>; + interrupts = <76 2 0 0>; + }; + dma-channel@380 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x380 0x80>; + interrupts = <77 2 0 0>; + }; + dma-channel@400 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x400 0x80>; + interrupts = <78 2 0 0>; + }; + dma-channel@480 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x480 0x80>; + interrupts = <79 2 0 0>; + }; +}; diff --git a/arch/powerpc/boot/dts/fsl/elo3-dma-1.dtsi b/arch/powerpc/boot/dts/fsl/elo3-dma-1.dtsi new file mode 100644 index 00000000000..cccf3bb3822 --- /dev/null +++ b/arch/powerpc/boot/dts/fsl/elo3-dma-1.dtsi @@ -0,0 +1,82 @@ +/* + * QorIQ Elo3 DMA device tree stub [ controller @ offset 0x101000 ] + * + * Copyright 2013 Freescale Semiconductor Inc. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions are met: + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * * Neither the name of Freescale Semiconductor nor the + * names of its contributors may be used to endorse or promote products + * derived from this software without specific prior written permission. + * + * + * ALTERNATIVELY, this software may be distributed under the terms of the + * GNU General Public License ("GPL") as published by the Free Software + * Foundation, either version 2 of that License or (at your option) any + * later version. + * + * THIS SOFTWARE IS PROVIDED BY Freescale Semiconductor ``AS IS'' AND ANY + * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED + * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL Freescale Semiconductor BE LIABLE FOR ANY + * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES + * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; + * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND + * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS + * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +dma1: dma@101300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,elo3-dma"; + reg = <0x101300 0x4>, + <0x101600 0x4>; + ranges = <0x0 0x101100 0x500>; + dma-channel@0 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + interrupts = <32 2 0 0>; + }; + dma-channel@80 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + interrupts = <33 2 0 0>; + }; + dma-channel@100 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + interrupts = <34 2 0 0>; + }; + dma-channel@180 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + interrupts = <35 2 0 0>; + }; + dma-channel@300 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x300 0x80>; + interrupts = <80 2 0 0>; + }; + dma-channel@380 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x380 0x80>; + interrupts = <81 2 0 0>; + }; + dma-channel@400 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x400 0x80>; + interrupts = <82 2 0 0>; + }; + dma-channel@480 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x480 0x80>; + interrupts = <83 2 0 0>; + }; +}; diff --git a/arch/powerpc/boot/dts/fsl/t4240si-post.dtsi b/arch/powerpc/boot/dts/fsl/t4240si-post.dtsi index 510afa362de..4143a9733cd 100644 --- a/arch/powerpc/boot/dts/fsl/t4240si-post.dtsi +++ b/arch/powerpc/boot/dts/fsl/t4240si-post.dtsi @@ -387,8 +387,8 @@ reg = <0xea000 0x4000>; }; -/include/ "qoriq-dma-0.dtsi" -/include/ "qoriq-dma-1.dtsi" +/include/ "elo3-dma-0.dtsi" +/include/ "elo3-dma-1.dtsi" /include/ "qoriq-espi-0.dtsi" spi@110000 { -- cgit v1.2.3-70-g09d2