From 4789998a30d845d94a7595076d1392ffd5a9d39e Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Wed, 24 Jun 2009 10:32:03 -0700 Subject: OMAP4: UART: cleanup special case IRQ handling Streamline the OMAP4 special IRQ assignments by putting inside normal init loop instead of having a separate loop. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/serial.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'arch/arm/mach-omap2/serial.c') diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index b094c15bfe4..c82ec95cd79 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -496,10 +496,6 @@ void __init omap_serial_init(void) if (info == NULL) return; - if (cpu_is_omap44xx()) { - for (i = 0; i < OMAP_MAX_NR_PORTS; i++) - serial_platform_data[i].irq += 32; - } for (i = 0; i < OMAP_MAX_NR_PORTS; i++) { struct plat_serial8250_port *p = serial_platform_data + i; @@ -533,6 +529,9 @@ void __init omap_serial_init(void) uart->p = p; list_add(&uart->node, &uart_list); + if (cpu_is_omap44xx()) + p->irq += 32; + omap_uart_enable_clocks(uart); omap_uart_reset(uart); omap_uart_idle_init(uart); -- cgit v1.2.3-70-g09d2 From 2466211e5debd205fc550d871fe0ab9b9a6d02ed Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Thu, 5 Mar 2009 16:32:23 +0200 Subject: OMAP3: Fixed crash bug with serial + suspend It was possible for an unhandled interrupt to occur if there was incoming serial traffic during wakeup from suspend. This was caused by the code in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time, but not acking its interrupts. Applies on top of PM branch. Use the PM begin/end hooks to ensure that the "serial idle" interrupts are disabled during the suspend path. Also, since begin/end hooks are now used, use the suspend_state that is passed in the begin hook instead of the enter hook as per the platform_suspend_ops docs. Signed-off-by: Tero Kristo Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 23 +++++++++++++++++++++-- arch/arm/mach-omap2/serial.c | 14 ++++++++++++++ arch/arm/plat-omap/include/mach/serial.h | 1 + 3 files changed, 36 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-omap2/serial.c') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 528f725722a..b07efb26de1 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -296,6 +296,8 @@ out: } #ifdef CONFIG_SUSPEND +static suspend_state_t suspend_state; + static int omap3_pm_prepare(void) { disable_hlt(); @@ -342,11 +344,11 @@ restore: return ret; } -static int omap3_pm_enter(suspend_state_t state) +static int omap3_pm_enter(suspend_state_t unused) { int ret = 0; - switch (state) { + switch (suspend_state) { case PM_SUSPEND_STANDBY: case PM_SUSPEND_MEM: ret = omap3_pm_suspend(); @@ -363,7 +365,24 @@ static void omap3_pm_finish(void) enable_hlt(); } +/* Hooks to enable / disable UART interrupts during suspend */ +static int omap3_pm_begin(suspend_state_t state) +{ + suspend_state = state; + omap_uart_enable_irqs(0); + return 0; +} + +static void omap3_pm_end(void) +{ + suspend_state = PM_SUSPEND_ON; + omap_uart_enable_irqs(1); + return; +} + static struct platform_suspend_ops omap_pm_ops = { + .begin = omap3_pm_begin, + .end = omap3_pm_end, .prepare = omap3_pm_prepare, .enter = omap3_pm_enter, .finish = omap3_pm_finish, diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index c82ec95cd79..5352d05b42d 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -435,6 +435,20 @@ static void omap_uart_idle_init(struct omap_uart_state *uart) WARN_ON(ret); } +void omap_uart_enable_irqs(int enable) +{ + int ret; + struct omap_uart_state *uart; + + list_for_each_entry(uart, &uart_list, node) { + if (enable) + ret = request_irq(uart->p->irq, omap_uart_interrupt, + IRQF_SHARED, "serial idle", (void *)uart); + else + free_irq(uart->p->irq, (void *)uart); + } +} + static ssize_t sleep_timeout_show(struct kobject *kobj, struct kobj_attribute *attr, char *buf) diff --git a/arch/arm/plat-omap/include/mach/serial.h b/arch/arm/plat-omap/include/mach/serial.h index 13abd02d152..def0529c75e 100644 --- a/arch/arm/plat-omap/include/mach/serial.h +++ b/arch/arm/plat-omap/include/mach/serial.h @@ -59,6 +59,7 @@ extern void omap_uart_check_wakeup(void); extern void omap_uart_prepare_suspend(void); extern void omap_uart_prepare_idle(int num); extern void omap_uart_resume_idle(int num); +extern void omap_uart_enable_irqs(int enable); #endif #endif -- cgit v1.2.3-70-g09d2 From fd455ea899b5a14a8cdd276e15f3b47696526f92 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 27 Apr 2009 12:27:36 -0700 Subject: OMAP2/3/4: UART: Allow per-UART disabling wakeup for serial ports This patch causes the OMAP uarts to honor the sysfs power/wakeup file for IOPAD wakeups. Before the OMAP was always woken up from off mode on a rs232 signal change. This patch also creates a different platform device for each serial port so that the wakeup properties can be control per port. By default, IOPAD wakeups are enabled for each UART. To disable, # echo disabled > /sys/devices/platform/serial8250.0/power/wakeup Where serial8250.0 can be replaced by .1, or .2 to control the other ports. Original idea and original patch from Russ Dill Cc: Russ Dill Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/serial.c | 174 ++++++++++++++++++++++++++++--------------- 1 file changed, 116 insertions(+), 58 deletions(-) (limited to 'arch/arm/mach-omap2/serial.c') diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 5352d05b42d..6f35a7e4893 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -54,6 +54,7 @@ struct omap_uart_state { struct plat_serial8250_port *p; struct list_head node; + struct platform_device pdev; #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM) int context_valid; @@ -68,10 +69,9 @@ struct omap_uart_state { #endif }; -static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS]; static LIST_HEAD(uart_list); -static struct plat_serial8250_port serial_platform_data[] = { +static struct plat_serial8250_port serial_platform_data0[] = { { .membase = IO_ADDRESS(OMAP_UART1_BASE), .mapbase = OMAP_UART1_BASE, @@ -81,6 +81,12 @@ static struct plat_serial8250_port serial_platform_data[] = { .regshift = 2, .uartclk = OMAP24XX_BASE_BAUD * 16, }, { + .flags = 0 + } +}; + +static struct plat_serial8250_port serial_platform_data1[] = { + { .membase = IO_ADDRESS(OMAP_UART2_BASE), .mapbase = OMAP_UART2_BASE, .irq = 73, @@ -89,6 +95,12 @@ static struct plat_serial8250_port serial_platform_data[] = { .regshift = 2, .uartclk = OMAP24XX_BASE_BAUD * 16, }, { + .flags = 0 + } +}; + +static struct plat_serial8250_port serial_platform_data2[] = { + { .membase = IO_ADDRESS(OMAP_UART3_BASE), .mapbase = OMAP_UART3_BASE, .irq = 74, @@ -217,6 +229,40 @@ static inline void omap_uart_disable_clocks(struct omap_uart_state *uart) clk_disable(uart->fck); } +static void omap_uart_enable_wakeup(struct omap_uart_state *uart) +{ + /* Set wake-enable bit */ + if (uart->wk_en && uart->wk_mask) { + u32 v = __raw_readl(uart->wk_en); + v |= uart->wk_mask; + __raw_writel(v, uart->wk_en); + } + + /* Ensure IOPAD wake-enables are set */ + if (cpu_is_omap34xx() && uart->padconf) { + u16 v = omap_ctrl_readw(uart->padconf); + v |= OMAP3_PADCONF_WAKEUPENABLE0; + omap_ctrl_writew(v, uart->padconf); + } +} + +static void omap_uart_disable_wakeup(struct omap_uart_state *uart) +{ + /* Clear wake-enable bit */ + if (uart->wk_en && uart->wk_mask) { + u32 v = __raw_readl(uart->wk_en); + v &= ~uart->wk_mask; + __raw_writel(v, uart->wk_en); + } + + /* Ensure IOPAD wake-enables are cleared */ + if (cpu_is_omap34xx() && uart->padconf) { + u16 v = omap_ctrl_readw(uart->padconf); + v &= ~OMAP3_PADCONF_WAKEUPENABLE0; + omap_ctrl_writew(v, uart->padconf); + } +} + static void omap_uart_smart_idle_enable(struct omap_uart_state *uart, int enable) { @@ -246,6 +292,11 @@ static void omap_uart_block_sleep(struct omap_uart_state *uart) static void omap_uart_allow_sleep(struct omap_uart_state *uart) { + if (device_may_wakeup(&uart->pdev.dev)) + omap_uart_enable_wakeup(uart); + else + omap_uart_disable_wakeup(uart); + if (!uart->clocked) return; @@ -292,7 +343,6 @@ void omap_uart_resume_idle(int num) /* Check for normal UART wakeup */ if (__raw_readl(uart->wk_st) & uart->wk_mask) omap_uart_block_sleep(uart); - return; } } @@ -346,16 +396,13 @@ static irqreturn_t omap_uart_interrupt(int irq, void *dev_id) return IRQ_NONE; } -static u32 sleep_timeout = DEFAULT_TIMEOUT; - static void omap_uart_idle_init(struct omap_uart_state *uart) { - u32 v; struct plat_serial8250_port *p = uart->p; int ret; uart->can_sleep = 0; - uart->timeout = sleep_timeout; + uart->timeout = DEFAULT_TIMEOUT; setup_timer(&uart->timer, omap_uart_idle_timer, (unsigned long) uart); mod_timer(&uart->timer, jiffies + uart->timeout); @@ -413,22 +460,6 @@ static void omap_uart_idle_init(struct omap_uart_state *uart) uart->padconf = 0; } - /* Set wake-enable bit */ - if (uart->wk_en && uart->wk_mask) { - v = __raw_readl(uart->wk_en); - v |= uart->wk_mask; - __raw_writel(v, uart->wk_en); - } - - /* Ensure IOPAD wake-enables are set */ - if (cpu_is_omap34xx() && uart->padconf) { - u16 v; - - v = omap_ctrl_readw(uart->padconf); - v |= OMAP3_PADCONF_WAKEUPENABLE0; - omap_ctrl_writew(v, uart->padconf); - } - p->flags |= UPF_SHARE_IRQ; ret = request_irq(p->irq, omap_uart_interrupt, IRQF_SHARED, "serial idle", (void *)uart); @@ -449,54 +480,81 @@ void omap_uart_enable_irqs(int enable) } } -static ssize_t sleep_timeout_show(struct kobject *kobj, - struct kobj_attribute *attr, +static ssize_t sleep_timeout_show(struct device *dev, + struct device_attribute *attr, char *buf) { - return sprintf(buf, "%u\n", sleep_timeout / HZ); + struct platform_device *pdev = container_of(dev, + struct platform_device, dev); + struct omap_uart_state *uart = container_of(pdev, + struct omap_uart_state, pdev); + + return sprintf(buf, "%u\n", uart->timeout / HZ); } -static ssize_t sleep_timeout_store(struct kobject *kobj, - struct kobj_attribute *attr, +static ssize_t sleep_timeout_store(struct device *dev, + struct device_attribute *attr, const char *buf, size_t n) { - struct omap_uart_state *uart; + struct platform_device *pdev = container_of(dev, + struct platform_device, dev); + struct omap_uart_state *uart = container_of(pdev, + struct omap_uart_state, pdev); unsigned int value; if (sscanf(buf, "%u", &value) != 1) { printk(KERN_ERR "sleep_timeout_store: Invalid value\n"); return -EINVAL; } - sleep_timeout = value * HZ; - list_for_each_entry(uart, &uart_list, node) { - uart->timeout = sleep_timeout; - if (uart->timeout) - mod_timer(&uart->timer, jiffies + uart->timeout); - else - /* A zero value means disable timeout feature */ - omap_uart_block_sleep(uart); - } + + uart->timeout = value * HZ; + if (uart->timeout) + mod_timer(&uart->timer, jiffies + uart->timeout); + else + /* A zero value means disable timeout feature */ + omap_uart_block_sleep(uart); + return n; } -static struct kobj_attribute sleep_timeout_attr = - __ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store); - +DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store); +#define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr)) #else static inline void omap_uart_idle_init(struct omap_uart_state *uart) {} +#define DEV_CREATE_FILE(dev, attr) #endif /* CONFIG_PM */ -static struct platform_device serial_device = { - .name = "serial8250", - .id = PLAT8250_DEV_PLATFORM, - .dev = { - .platform_data = serial_platform_data, +static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS] = { + { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev = { + .platform_data = serial_platform_data0, + }, + }, + }, { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM1, + .dev = { + .platform_data = serial_platform_data1, + }, + }, + }, { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM2, + .dev = { + .platform_data = serial_platform_data2, + }, + }, }, }; void __init omap_serial_init(void) { - int i, err; + int i; const struct omap_uart_config *info; char name[16]; @@ -512,8 +570,10 @@ void __init omap_serial_init(void) return; for (i = 0; i < OMAP_MAX_NR_PORTS; i++) { - struct plat_serial8250_port *p = serial_platform_data + i; struct omap_uart_state *uart = &omap_uart[i]; + struct platform_device *pdev = &uart->pdev; + struct device *dev = &pdev->dev; + struct plat_serial8250_port *p = dev->platform_data; if (!(info->enabled_uarts & (1 << i))) { p->membase = NULL; @@ -549,15 +609,13 @@ void __init omap_serial_init(void) omap_uart_enable_clocks(uart); omap_uart_reset(uart); omap_uart_idle_init(uart); - } - - err = platform_device_register(&serial_device); - -#ifdef CONFIG_PM - if (!err) - err = sysfs_create_file(&serial_device.dev.kobj, - &sleep_timeout_attr.attr); -#endif + if (WARN_ON(platform_device_register(pdev))) + continue; + if ((cpu_is_omap34xx() && uart->padconf) || + (uart->wk_en && uart->wk_mask)) { + device_init_wakeup(dev, true); + DEV_CREATE_FILE(dev, &dev_attr_sleep_timeout); + } + } } - -- cgit v1.2.3-70-g09d2 From bcf396c48012a5e4c7ab77be5c40df10d6bdb8ad Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 30 Jun 2009 21:02:45 -0700 Subject: OMAP2/3/4: UART: allow in-order port traversal Use list_add_tail() when adding discovered UART ports. This is so traversal using list_for_each_entry() will traverse the list in the order they were found. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/serial.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2/serial.c') diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 6f35a7e4893..a7421a50410 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -601,7 +601,7 @@ void __init omap_serial_init(void) uart->num = i; p->private_data = uart; uart->p = p; - list_add(&uart->node, &uart_list); + list_add_tail(&uart->node, &uart_list); if (cpu_is_omap44xx()) p->irq += 32; -- cgit v1.2.3-70-g09d2