From 6adb8f388ef2f23d4a81e1e42d15f22d62749a06 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 19 Jun 2009 19:08:24 -0600 Subject: OMAP3 clock: remove wait for DPLL3 M2 clock to stabilize The original CDP kernel that this code comes from waited for 0x800 loops after switching the CORE DPLL M2 divider. This does not appear to be necessary. Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/sram34xx.S | 3 --- 1 file changed, 3 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index c080c82521e..84781a6cd26 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -102,9 +102,6 @@ configure_core_dpll: orr r12, r12, r3, lsl #0x1B @ r3 contains the M2 val str r12, [r11] ldr r12, [r11] @ posted-write barrier for CM - mov r12, #0x800 @ wait for the clock to stabilise - cmp r3, #2 - bne wait_clk_stable bx lr wait_clk_stable: subs r12, r12, #1 -- cgit v1.2.3-70-g09d2 From 2f135eaf182761bb9a5cbd5138a447b0ad2a1fef Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 19 Jun 2009 19:08:25 -0600 Subject: OMAP3 clock: initialize SDRC timings at kernel start On the OMAP3, initialize SDRC timings when the kernel boots. This ensures that the kernel is running with known, optimized SDRC timings, rather than whatever was configured by the bootloader. Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/clock34xx.c | 3 --- arch/arm/mach-omap2/io.c | 36 ++++++++++++++++++++++++++++++++++++ 2 files changed, 36 insertions(+), 3 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index 9e43fe5209d..5458ab3bf65 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -718,9 +718,6 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) if (clk != &dpll3_m2_ck) return -EINVAL; - if (rate == clk->rate) - return 0; - validrate = omap2_clksel_round_rate_div(clk, rate, &new_div); if (validrate != rate) return -EINVAL; diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index 32afd944821..3a86b0f6603 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -21,6 +21,7 @@ #include #include #include +#include #include @@ -241,6 +242,40 @@ void __init omap2_map_common_io(void) omapfb_reserve_sdram(); } +/* + * omap2_init_reprogram_sdrc - reprogram SDRC timing parameters + * + * Sets the CORE DPLL3 M2 divider to the same value that it's at + * currently. This has the effect of setting the SDRC SDRAM AC timing + * registers to the values currently defined by the kernel. Currently + * only defined for OMAP3; will return 0 if called on OMAP2. Returns + * -EINVAL if the dpll3_m2_ck cannot be found, 0 if called on OMAP2, + * or passes along the return value of clk_set_rate(). + */ +static int __init _omap2_init_reprogram_sdrc(void) +{ + struct clk *dpll3_m2_ck; + int v = -EINVAL; + long rate; + + if (!cpu_is_omap34xx()) + return 0; + + dpll3_m2_ck = clk_get(NULL, "dpll3_m2_ck"); + if (!dpll3_m2_ck) + return -EINVAL; + + rate = clk_get_rate(dpll3_m2_ck); + pr_info("Reprogramming SDRC clock to %ld Hz\n", rate); + v = clk_set_rate(dpll3_m2_ck, rate); + if (v) + pr_err("dpll3_m2_clk rate change failed: %d\n", v); + + clk_put(dpll3_m2_ck); + + return v; +} + void __init omap2_init_common_hw(struct omap_sdrc_params *sp) { omap2_mux_init(); @@ -249,6 +284,7 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sp) clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps); omap2_clk_init(); omap2_sdrc_init(sp); + _omap2_init_reprogram_sdrc(); #endif gpmc_init(); } -- cgit v1.2.3-70-g09d2 From c9812d042a21eb492a36cfabf9f41107f5ecee3d Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 19 Jun 2009 19:08:26 -0600 Subject: OMAP3 clock: add a short delay when lowering CORE clk rate When changing the SDRAM clock from 166MHz to 83MHz via the CORE DPLL M2 divider, add a short delay before returning to SDRAM to allow the SDRC time to stabilize. Without this delay, the system is prone to random panics upon re-entering SDRAM. This time delay varies based on MPU frequency. At 500MHz MPU frequency at room temperature, 64 loops seems to work okay; so add another 32 loops for environmental and process variation. Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/clock34xx.c | 30 ++++++++++++++++++++++++++++-- arch/arm/mach-omap2/sram34xx.S | 20 +++++++++----------- arch/arm/plat-omap/include/mach/sram.h | 4 ++-- arch/arm/plat-omap/sram.c | 8 +++++--- 4 files changed, 44 insertions(+), 18 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index 5458ab3bf65..4bfa650bb34 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -286,6 +286,20 @@ static struct omap_clk omap34xx_clks[] = { #define MIN_SDRC_DLL_LOCK_FREQ 83000000 +#define CYCLES_PER_MHZ 1000000 + +/* Scale factor for fixed-point arith in omap3_core_dpll_m2_set_rate() */ +#define SDRC_MPURATE_SCALE 8 + +/* 2^SDRC_MPURATE_BASE_SHIFT: MPU MHz that SDRC_MPURATE_LOOPS is defined for */ +#define SDRC_MPURATE_BASE_SHIFT 9 + +/* + * SDRC_MPURATE_LOOPS: Number of MPU loops to execute at + * 2^MPURATE_BASE_SHIFT MHz for SDRC to stabilize + */ +#define SDRC_MPURATE_LOOPS 96 + /** * omap3_dpll_recalc - recalculate DPLL rate * @clk: DPLL struct clk @@ -709,7 +723,8 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) { u32 new_div = 0; u32 unlock_dll = 0; - unsigned long validrate, sdrcrate; + u32 c; + unsigned long validrate, sdrcrate, mpurate; struct omap_sdrc_params *sp; if (!clk || !rate) @@ -737,6 +752,17 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) unlock_dll = 1; } + /* + * XXX This only needs to be done when the CPU frequency changes + */ + mpurate = arm_fck.rate / CYCLES_PER_MHZ; + c = (mpurate << SDRC_MPURATE_SCALE) >> SDRC_MPURATE_BASE_SHIFT; + c += 1; /* for safety */ + c *= SDRC_MPURATE_LOOPS; + c >>= SDRC_MPURATE_SCALE; + if (c == 0) + c = 1; + pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate, validrate); pr_debug("clock: SDRC timing params used: %08x %08x %08x\n", @@ -747,7 +773,7 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) /* REVISIT: Add SDRC_MR changing to this code also */ omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla, - sp->actim_ctrlb, new_div, unlock_dll); + sp->actim_ctrlb, new_div, unlock_dll, c); return 0; } diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index 84781a6cd26..8d4a88c3071 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -42,10 +42,14 @@ * r0 = sdrc_rfr_ctrl r1 = sdrc_actim_ctrla r2 = sdrc_actim_ctrlb r3 = M2 * r4 = Unlock SDRC DLL? (1 = yes, 0 = no) -- only unlock DLL for * SDRC rates < 83MHz + * r5 = number of MPU cycles to wait for SDRC to stabilize after + * reprogramming the SDRC when switching to a slower MPU speed + * */ ENTRY(omap3_sram_configure_core_dpll) stmfd sp!, {r1-r12, lr} @ store regs to stack ldr r4, [sp, #52] @ pull extra args off the stack + ldr r5, [sp, #56] @ load extra args from the stack dsb @ flush buffered writes to interconnect cmp r3, #0x2 blne configure_sdrc @@ -59,7 +63,11 @@ ENTRY(omap3_sram_configure_core_dpll) bleq wait_dll_unlock blne wait_dll_lock cmp r3, #0x1 - blne configure_sdrc + beq return_to_sdram + bl configure_sdrc + mov r12, r5 @ if slowing, wait for SDRC to stabilize + bl wait_clk_stable +return_to_sdram: isb @ prevent speculative exec past here mov r0, #0 @ return value ldmfd sp!, {r1-r12, pc} @ restore regs and return @@ -106,16 +114,6 @@ configure_core_dpll: wait_clk_stable: subs r12, r12, #1 bne wait_clk_stable - nop - nop - nop - nop - nop - nop - nop - nop - nop - nop bx lr enable_sdrc: ldr r11, omap3_cm_iclken1_core diff --git a/arch/arm/plat-omap/include/mach/sram.h b/arch/arm/plat-omap/include/mach/sram.h index dca7c16ae90..c32fa0a220d 100644 --- a/arch/arm/plat-omap/include/mach/sram.h +++ b/arch/arm/plat-omap/include/mach/sram.h @@ -24,7 +24,7 @@ extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll); + u32 unlock_dll, u32 f); /* Do not use these */ extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl); @@ -62,7 +62,7 @@ extern unsigned long omap243x_sram_reprogram_sdrc_sz; extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll); + u32 unlock_dll, u32 f); extern unsigned long omap3_sram_configure_core_dpll_sz; #endif diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index a5b9bcd6b10..79c0f025442 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -371,15 +371,17 @@ static inline int omap243x_sram_init(void) static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, - u32 m2, u32 unlock_dll); + u32 m2, u32 unlock_dll, + u32 f); u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll) + u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll, + u32 f) { BUG_ON(!_omap3_sram_configure_core_dpll); return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl, sdrc_actim_ctrla, sdrc_actim_ctrlb, m2, - unlock_dll); + unlock_dll, f); } /* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */ -- cgit v1.2.3-70-g09d2 From d0ba3922ae241a87d22a1c3ffad72b96fe993c9a Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 19 Jun 2009 19:08:27 -0600 Subject: OMAP3 clock/SDRC: program SDRC_MR register during SDRC clock change Program the SDRC_MR_0 register as well during SDRC clock changes. This register allows selection of the memory CAS latency. Some SDRAM chips, such as the Qimonda HYB18M512160AF6, have a lower CAS latency at lower clock rates. Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/clock34xx.c | 4 ++-- arch/arm/mach-omap2/sram34xx.S | 8 +++++++- arch/arm/plat-omap/include/mach/sram.h | 4 ++-- arch/arm/plat-omap/sram.c | 6 +++--- 4 files changed, 14 insertions(+), 8 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index 4bfa650bb34..cf41ab55fa9 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -771,9 +771,9 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) /* REVISIT: SRAM code doesn't support other M2 divisors yet */ WARN_ON(new_div != 1 && new_div != 2); - /* REVISIT: Add SDRC_MR changing to this code also */ omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla, - sp->actim_ctrlb, new_div, unlock_dll, c); + sp->actim_ctrlb, new_div, unlock_dll, c, + sp->mr); return 0; } diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index 8d4a88c3071..d13f1cc4bd5 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -44,12 +44,14 @@ * SDRC rates < 83MHz * r5 = number of MPU cycles to wait for SDRC to stabilize after * reprogramming the SDRC when switching to a slower MPU speed + * r6 = SDRC_MR_0 register value * */ ENTRY(omap3_sram_configure_core_dpll) stmfd sp!, {r1-r12, lr} @ store regs to stack ldr r4, [sp, #52] @ pull extra args off the stack ldr r5, [sp, #56] @ load extra args from the stack + ldr r6, [sp, #60] @ load extra args from the stack dsb @ flush buffered writes to interconnect cmp r3, #0x2 blne configure_sdrc @@ -151,7 +153,9 @@ configure_sdrc: str r1, [r11] ldr r11, omap3_sdrc_actim_ctrlb str r2, [r11] - ldr r2, [r11] @ posted-write barrier for SDRC + ldr r11, omap3_sdrc_mr_0 + str r6, [r11] + ldr r6, [r11] @ posted-write barrier for SDRC bx lr omap3_sdrc_power: @@ -168,6 +172,8 @@ omap3_sdrc_actim_ctrla: .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0) omap3_sdrc_actim_ctrlb: .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0) +omap3_sdrc_mr_0: + .word OMAP34XX_SDRC_REGADDR(SDRC_MR_0) omap3_sdrc_dlla_status: .word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS) omap3_sdrc_dlla_ctrl: diff --git a/arch/arm/plat-omap/include/mach/sram.h b/arch/arm/plat-omap/include/mach/sram.h index c32fa0a220d..4f87056a367 100644 --- a/arch/arm/plat-omap/include/mach/sram.h +++ b/arch/arm/plat-omap/include/mach/sram.h @@ -24,7 +24,7 @@ extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll, u32 f); + u32 unlock_dll, u32 f, u32 sdrc_mr); /* Do not use these */ extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl); @@ -62,7 +62,7 @@ extern unsigned long omap243x_sram_reprogram_sdrc_sz; extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll, u32 f); + u32 unlock_dll, u32 f, u32 sdrc_mr); extern unsigned long omap3_sram_configure_core_dpll_sz; #endif diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index 79c0f025442..7dadf1a59fb 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -372,16 +372,16 @@ static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll, - u32 f); + u32 f, u32 sdrc_mr); u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll, - u32 f) + u32 f, u32 sdrc_mr) { BUG_ON(!_omap3_sram_configure_core_dpll); return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl, sdrc_actim_ctrla, sdrc_actim_ctrlb, m2, - unlock_dll, f); + unlock_dll, f, sdrc_mr); } /* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */ -- cgit v1.2.3-70-g09d2 From 4267b5d15269ea6b26736a2ccd4c213e63e547ab Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 19 Jun 2009 19:08:27 -0600 Subject: OMAP3 SRAM: add more comments on the SRAM code Clean up comments and copyrights on the CORE DPLL3 M2 divider change code. Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/sram34xx.S | 45 ++++++++++++++++++++++-------------------- 1 file changed, 24 insertions(+), 21 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index d13f1cc4bd5..37a1e1fc0ab 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -3,13 +3,12 @@ * * Omap3 specific functions that need to be run in internal SRAM * - * (C) Copyright 2007 - * Texas Instruments Inc. - * Rajendra Nayak + * Copyright (C) 2004, 2007, 2008 Texas Instruments, Inc. + * Copyright (C) 2008 Nokia Corporation * - * (C) Copyright 2004 - * Texas Instruments, + * Rajendra Nayak * Richard Woodruff + * Paul Walmsley * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -38,13 +37,16 @@ .text /* - * Change frequency of core dpll - * r0 = sdrc_rfr_ctrl r1 = sdrc_actim_ctrla r2 = sdrc_actim_ctrlb r3 = M2 - * r4 = Unlock SDRC DLL? (1 = yes, 0 = no) -- only unlock DLL for + * omap3_sram_configure_core_dpll - change DPLL3 M2 divider + * r0 = new SDRC_RFR_CTRL register contents + * r1 = new SDRC_ACTIM_CTRLA register contents + * r2 = new SDRC_ACTIM_CTRLB register contents + * r3 = new M2 divider setting (only 1 and 2 supported right now) + * r4 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for * SDRC rates < 83MHz * r5 = number of MPU cycles to wait for SDRC to stabilize after * reprogramming the SDRC when switching to a slower MPU speed - * r6 = SDRC_MR_0 register value + * r6 = new SDRC_MR_0 register value * */ ENTRY(omap3_sram_configure_core_dpll) @@ -53,22 +55,22 @@ ENTRY(omap3_sram_configure_core_dpll) ldr r5, [sp, #56] @ load extra args from the stack ldr r6, [sp, #60] @ load extra args from the stack dsb @ flush buffered writes to interconnect - cmp r3, #0x2 - blne configure_sdrc - cmp r4, #0x1 + cmp r3, #0x2 @ if increasing SDRC clk rate, + blne configure_sdrc @ program the SDRC regs early (for RFR) + cmp r4, #0x1 @ set the intended DLL state bleq unlock_dll blne lock_dll - bl sdram_in_selfrefresh @ put the SDRAM in self refresh - bl configure_core_dpll - bl enable_sdrc - cmp r4, #0x1 + bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC + bl configure_core_dpll @ change the DPLL3 M2 divider + bl enable_sdrc @ take SDRC out of idle + cmp r4, #0x1 @ wait for DLL status to change bleq wait_dll_unlock blne wait_dll_lock - cmp r3, #0x1 - beq return_to_sdram - bl configure_sdrc - mov r12, r5 @ if slowing, wait for SDRC to stabilize - bl wait_clk_stable + cmp r3, #0x1 @ if increasing SDRC clk rate, + beq return_to_sdram @ return to SDRAM code, otherwise, + bl configure_sdrc @ reprogram SDRC regs now + mov r12, r5 + bl wait_clk_stable @ wait for SDRC to stabilize return_to_sdram: isb @ prevent speculative exec past here mov r0, #0 @ return value @@ -93,6 +95,7 @@ sdram_in_selfrefresh: bic r12, r12, #0x4 @ clear PWDENA str r12, [r11] @ write back to SDRC_POWER register ldr r12, [r11] @ posted-write barrier for SDRC +idle_sdrc: ldr r11, omap3_cm_iclken1_core @ read the CM_ICLKEN1_CORE reg ldr r12, [r11] bic r12, r12, #0x2 @ disable iclk bit for SDRC -- cgit v1.2.3-70-g09d2 From df14e4747aa58126a508ae26661c73d83127c831 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 19 Jun 2009 19:08:28 -0600 Subject: OMAP3 SRAM: convert SRAM code to use macros rather than magic numbers Convert omap3_sram_configure_core_dpll() to use macros rather than magic numbers. Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/sram34xx.S | 53 ++++++++++++++++++++++++++++++------------ 1 file changed, 38 insertions(+), 15 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index 37a1e1fc0ab..16eb4efa8b7 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -36,6 +36,29 @@ .text +/* r4 parameters */ +#define SDRC_NO_UNLOCK_DLL 0x0 +#define SDRC_UNLOCK_DLL 0x1 + +/* SDRC_DLLA_CTRL bit settings */ +#define DLLIDLE_MASK 0x4 + +/* SDRC_DLLA_STATUS bit settings */ +#define LOCKSTATUS_MASK 0x4 + +/* SDRC_POWER bit settings */ +#define SRFRONIDLEREQ_MASK 0x40 +#define PWDENA_MASK 0x4 + +/* CM_IDLEST1_CORE bit settings */ +#define ST_SDRC_MASK 0x2 + +/* CM_ICLKEN1_CORE bit settings */ +#define EN_SDRC_MASK 0x2 + +/* CM_CLKSEL1_PLL bit settings */ +#define CORE_DPLL_CLKOUT_DIV_SHIFT 0x1b + /* * omap3_sram_configure_core_dpll - change DPLL3 M2 divider * r0 = new SDRC_RFR_CTRL register contents @@ -57,13 +80,13 @@ ENTRY(omap3_sram_configure_core_dpll) dsb @ flush buffered writes to interconnect cmp r3, #0x2 @ if increasing SDRC clk rate, blne configure_sdrc @ program the SDRC regs early (for RFR) - cmp r4, #0x1 @ set the intended DLL state + cmp r4, #SDRC_UNLOCK_DLL @ set the intended DLL state bleq unlock_dll blne lock_dll bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC bl configure_core_dpll @ change the DPLL3 M2 divider bl enable_sdrc @ take SDRC out of idle - cmp r4, #0x1 @ wait for DLL status to change + cmp r4, #SDRC_UNLOCK_DLL @ wait for DLL status to change bleq wait_dll_unlock blne wait_dll_lock cmp r3, #0x1 @ if increasing SDRC clk rate, @@ -78,33 +101,33 @@ return_to_sdram: unlock_dll: ldr r11, omap3_sdrc_dlla_ctrl ldr r12, [r11] - orr r12, r12, #0x4 + orr r12, r12, #DLLIDLE_MASK str r12, [r11] @ (no OCP barrier needed) bx lr lock_dll: ldr r11, omap3_sdrc_dlla_ctrl ldr r12, [r11] - bic r12, r12, #0x4 + bic r12, r12, #DLLIDLE_MASK str r12, [r11] @ (no OCP barrier needed) bx lr sdram_in_selfrefresh: ldr r11, omap3_sdrc_power @ read the SDRC_POWER register ldr r12, [r11] @ read the contents of SDRC_POWER mov r9, r12 @ keep a copy of SDRC_POWER bits - orr r12, r12, #0x40 @ enable self refresh on idle req - bic r12, r12, #0x4 @ clear PWDENA + orr r12, r12, #SRFRONIDLEREQ_MASK @ enable self refresh on idle + bic r12, r12, #PWDENA_MASK @ clear PWDENA str r12, [r11] @ write back to SDRC_POWER register ldr r12, [r11] @ posted-write barrier for SDRC idle_sdrc: ldr r11, omap3_cm_iclken1_core @ read the CM_ICLKEN1_CORE reg ldr r12, [r11] - bic r12, r12, #0x2 @ disable iclk bit for SDRC + bic r12, r12, #EN_SDRC_MASK @ disable iclk bit for SDRC str r12, [r11] wait_sdrc_idle: ldr r11, omap3_cm_idlest1_core ldr r12, [r11] - and r12, r12, #0x2 @ check for SDRC idle - cmp r12, #2 + and r12, r12, #ST_SDRC_MASK @ check for SDRC idle + cmp r12, #ST_SDRC_MASK bne wait_sdrc_idle bx lr configure_core_dpll: @@ -112,7 +135,7 @@ configure_core_dpll: ldr r12, [r11] ldr r10, core_m2_mask_val @ modify m2 for core dpll and r12, r12, r10 - orr r12, r12, r3, lsl #0x1B @ r3 contains the M2 val + orr r12, r12, r3, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT str r12, [r11] ldr r12, [r11] @ posted-write barrier for CM bx lr @@ -123,12 +146,12 @@ wait_clk_stable: enable_sdrc: ldr r11, omap3_cm_iclken1_core ldr r12, [r11] - orr r12, r12, #0x2 @ enable iclk bit for SDRC + orr r12, r12, #EN_SDRC_MASK @ enable iclk bit for SDRC str r12, [r11] wait_sdrc_idle1: ldr r11, omap3_cm_idlest1_core ldr r12, [r11] - and r12, r12, #0x2 + and r12, r12, #ST_SDRC_MASK cmp r12, #0 bne wait_sdrc_idle1 restore_sdrc_power_val: @@ -138,14 +161,14 @@ restore_sdrc_power_val: wait_dll_lock: ldr r11, omap3_sdrc_dlla_status ldr r12, [r11] - and r12, r12, #0x4 - cmp r12, #0x4 + and r12, r12, #LOCKSTATUS_MASK + cmp r12, #LOCKSTATUS_MASK bne wait_dll_lock bx lr wait_dll_unlock: ldr r11, omap3_sdrc_dlla_status ldr r12, [r11] - and r12, r12, #0x4 + and r12, r12, #LOCKSTATUS_MASK cmp r12, #0x0 bne wait_dll_unlock bx lr -- cgit v1.2.3-70-g09d2 From 3afec6332e1e7cf2d74e0bf08160a68f43a59073 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Fri, 19 Jun 2009 19:08:29 -0600 Subject: OMAP3: Add support for DPLL3 divisor values higher than 2 Previously only 1 and 2 was supported. This is needed for DVFS VDD2 control. Signed-off-by: Tero Kristo --- arch/arm/mach-omap2/clock34xx.c | 9 +++------ arch/arm/mach-omap2/sram34xx.S | 8 +++++--- arch/arm/plat-omap/include/mach/sram.h | 6 ++++-- arch/arm/plat-omap/sram.c | 6 +++--- 4 files changed, 15 insertions(+), 14 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index cf41ab55fa9..045da923e75 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -739,9 +739,9 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) sdrcrate = sdrc_ick.rate; if (rate > clk->rate) - sdrcrate <<= ((rate / clk->rate) - 1); + sdrcrate <<= ((rate / clk->rate) >> 1); else - sdrcrate >>= ((clk->rate / rate) - 1); + sdrcrate >>= ((clk->rate / rate) >> 1); sp = omap2_sdrc_get_params(sdrcrate); if (!sp) @@ -768,12 +768,9 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) pr_debug("clock: SDRC timing params used: %08x %08x %08x\n", sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb); - /* REVISIT: SRAM code doesn't support other M2 divisors yet */ - WARN_ON(new_div != 1 && new_div != 2); - omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb, new_div, unlock_dll, c, - sp->mr); + sp->mr, rate > clk->rate); return 0; } diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index 16eb4efa8b7..487fa8609cd 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -70,6 +70,7 @@ * r5 = number of MPU cycles to wait for SDRC to stabilize after * reprogramming the SDRC when switching to a slower MPU speed * r6 = new SDRC_MR_0 register value + * r7 = increasing SDRC rate? (1 = yes, 0 = no) * */ ENTRY(omap3_sram_configure_core_dpll) @@ -77,9 +78,10 @@ ENTRY(omap3_sram_configure_core_dpll) ldr r4, [sp, #52] @ pull extra args off the stack ldr r5, [sp, #56] @ load extra args from the stack ldr r6, [sp, #60] @ load extra args from the stack + ldr r7, [sp, #64] @ load extra args from the stack dsb @ flush buffered writes to interconnect - cmp r3, #0x2 @ if increasing SDRC clk rate, - blne configure_sdrc @ program the SDRC regs early (for RFR) + cmp r7, #1 @ if increasing SDRC clk rate, + bleq configure_sdrc @ program the SDRC regs early (for RFR) cmp r4, #SDRC_UNLOCK_DLL @ set the intended DLL state bleq unlock_dll blne lock_dll @@ -89,7 +91,7 @@ ENTRY(omap3_sram_configure_core_dpll) cmp r4, #SDRC_UNLOCK_DLL @ wait for DLL status to change bleq wait_dll_unlock blne wait_dll_lock - cmp r3, #0x1 @ if increasing SDRC clk rate, + cmp r7, #1 @ if increasing SDRC clk rate, beq return_to_sdram @ return to SDRAM code, otherwise, bl configure_sdrc @ reprogram SDRC regs now mov r12, r5 diff --git a/arch/arm/plat-omap/include/mach/sram.h b/arch/arm/plat-omap/include/mach/sram.h index 4f87056a367..4d53cc59d7a 100644 --- a/arch/arm/plat-omap/include/mach/sram.h +++ b/arch/arm/plat-omap/include/mach/sram.h @@ -24,7 +24,8 @@ extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll, u32 f, u32 sdrc_mr); + u32 unlock_dll, u32 f, u32 sdrc_mr, + u32 inc); /* Do not use these */ extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl); @@ -62,7 +63,8 @@ extern unsigned long omap243x_sram_reprogram_sdrc_sz; extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll, u32 f, u32 sdrc_mr); + u32 unlock_dll, u32 f, u32 sdrc_mr, + u32 inc); extern unsigned long omap3_sram_configure_core_dpll_sz; #endif diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index 7dadf1a59fb..65006df3f1b 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -372,16 +372,16 @@ static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll, - u32 f, u32 sdrc_mr); + u32 f, u32 sdrc_mr, u32 inc); u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll, - u32 f, u32 sdrc_mr) + u32 f, u32 sdrc_mr, u32 inc) { BUG_ON(!_omap3_sram_configure_core_dpll); return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl, sdrc_actim_ctrla, sdrc_actim_ctrlb, m2, - unlock_dll, f, sdrc_mr); + unlock_dll, f, sdrc_mr, inc); } /* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */ -- cgit v1.2.3-70-g09d2 From 7b7bcefa35d62fec64c3615a6bef7866f34c7cc9 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 19 Jun 2009 19:08:29 -0600 Subject: OMAP3 SDRC: set FIXEDDELAY when disabling SDRC DLL Correspondence with the TI OMAP hardware team indicates that SDRC_DLLA_CTRL.FIXEDDELAY should be initialized to 0x0f. This number was apparently derived from process validation. This is only used when the SDRC DLL is unlocked (e.g., SDRC clock frequency less than 83MHz). Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/sram34xx.S | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index 487fa8609cd..f41f8d96ddb 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -41,8 +41,18 @@ #define SDRC_UNLOCK_DLL 0x1 /* SDRC_DLLA_CTRL bit settings */ +#define FIXEDDELAY_SHIFT 24 +#define FIXEDDELAY_MASK (0xff << FIXEDDELAY_SHIFT) #define DLLIDLE_MASK 0x4 +/* + * SDRC_DLLA_CTRL default values: TI hardware team indicates that + * FIXEDDELAY should be initialized to 0xf. This apparently was + * empirically determined during process testing, so no derivation + * was provided. + */ +#define FIXEDDELAY_DEFAULT (0x0f << FIXEDDELAY_SHIFT) + /* SDRC_DLLA_STATUS bit settings */ #define LOCKSTATUS_MASK 0x4 @@ -103,6 +113,8 @@ return_to_sdram: unlock_dll: ldr r11, omap3_sdrc_dlla_ctrl ldr r12, [r11] + and r12, r12, #FIXEDDELAY_MASK + orr r12, r12, #FIXEDDELAY_DEFAULT orr r12, r12, #DLLIDLE_MASK str r12, [r11] @ (no OCP barrier needed) bx lr -- cgit v1.2.3-70-g09d2 From 2687069f3ac297b820c58de7222e4d16adbca498 Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Fri, 19 Jun 2009 19:08:30 -0600 Subject: OMAP2 clock/powerdomain: off by 1 error in loop timeout comparisons with while (i++ < MAX_CLOCK_ENABLE_WAIT); i can reach MAX_CLOCK_ENABLE_WAIT + 1 after the loop, so if (i == MAX_CLOCK_ENABLE_WAIT) that's still success. Signed-off-by: Roel Kluin Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/clock.c | 2 +- arch/arm/mach-omap2/powerdomain.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index ba528f85749..b0665f161c0 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -302,7 +302,7 @@ int omap2_wait_clock_ready(void __iomem *reg, u32 mask, const char *name) udelay(1); } - if (i < MAX_CLOCK_ENABLE_WAIT) + if (i <= MAX_CLOCK_ENABLE_WAIT) pr_debug("Clock %s stable after %d loops\n", name, i); else printk(KERN_ERR "Clock %s didn't enable in %d tries\n", diff --git a/arch/arm/mach-omap2/powerdomain.c b/arch/arm/mach-omap2/powerdomain.c index 73e2971b175..983f1cb676b 100644 --- a/arch/arm/mach-omap2/powerdomain.c +++ b/arch/arm/mach-omap2/powerdomain.c @@ -1099,7 +1099,7 @@ int pwrdm_wait_transition(struct powerdomain *pwrdm) (c++ < PWRDM_TRANSITION_BAILOUT)) udelay(1); - if (c >= PWRDM_TRANSITION_BAILOUT) { + if (c > PWRDM_TRANSITION_BAILOUT) { printk(KERN_ERR "powerdomain: waited too long for " "powerdomain %s to complete transition\n", pwrdm->name); return -EAGAIN; -- cgit v1.2.3-70-g09d2 From 762ad3a476baa1831f732488e80960f4aa024393 Mon Sep 17 00:00:00 2001 From: Grazvydas Ignotas Date: Tue, 23 Jun 2009 13:30:22 +0300 Subject: OMAP2/3: mmc-twl4030: use correct controller in twl_mmc23_set_power twl_mmc23_set_power() has MMC2 twl_mmc_controller hardcoded in it, which breaks MMC3. Find the right controller to use instead. Signed-off-by: Grazvydas Ignotas Cc: David Brownell Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/mmc-twl4030.c | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/mmc-twl4030.c b/arch/arm/mach-omap2/mmc-twl4030.c index 9756a878fd9..1541fd4c8d0 100644 --- a/arch/arm/mach-omap2/mmc-twl4030.c +++ b/arch/arm/mach-omap2/mmc-twl4030.c @@ -263,8 +263,19 @@ static int twl_mmc1_set_power(struct device *dev, int slot, int power_on, static int twl_mmc23_set_power(struct device *dev, int slot, int power_on, int vdd) { int ret = 0; - struct twl_mmc_controller *c = &hsmmc[1]; + struct twl_mmc_controller *c = NULL; struct omap_mmc_platform_data *mmc = dev->platform_data; + int i; + + for (i = 1; i < ARRAY_SIZE(hsmmc); i++) { + if (mmc == hsmmc[i].mmc) { + c = &hsmmc[i]; + break; + } + } + + if (c == NULL) + return -ENODEV; /* If we don't see a Vcc regulator, assume it's a fixed * voltage always-on regulator. -- cgit v1.2.3-70-g09d2 From 091a58af0ba1765d80b1e74382c7572baceb1bdc Mon Sep 17 00:00:00 2001 From: Roel Kluin Date: Tue, 23 Jun 2009 13:30:22 +0300 Subject: OMAP2/3: omap mailbox: platform_get_irq() error ignored platform_get_irq may return -ENXIO. but struct omap_mbox mbox_dsp_info.irq is unsigned, so the error was not noticed. Signed-off-by: Roel Kluin Signed-off-by: Hiroshi DOYU Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/mailbox.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/mailbox.c b/arch/arm/mach-omap2/mailbox.c index fd5b8a5925c..6f71f3730c9 100644 --- a/arch/arm/mach-omap2/mailbox.c +++ b/arch/arm/mach-omap2/mailbox.c @@ -282,12 +282,12 @@ static int __devinit omap2_mbox_probe(struct platform_device *pdev) return -ENOMEM; /* DSP or IVA2 IRQ */ - mbox_dsp_info.irq = platform_get_irq(pdev, 0); - if (mbox_dsp_info.irq < 0) { + ret = platform_get_irq(pdev, 0); + if (ret < 0) { dev_err(&pdev->dev, "invalid irq resource\n"); - ret = -ENODEV; goto err_dsp; } + mbox_dsp_info.irq = ret; ret = omap_mbox_register(&pdev->dev, &mbox_dsp_info); if (ret) -- cgit v1.2.3-70-g09d2 From 8e25ad964aac0bf6b30dd013303750089f819679 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 23 Jun 2009 13:30:23 +0300 Subject: OMAP2/3: Add omap_type() for determining GP/EMU/HS The omap_type() function is added and returns the DEVICETYPE field of the CONTROL_STATUS register. The result can be used for conditional code based on whether device is GP (general purpose), EMU or HS (high security). Also move the type defines so omap1 code compile does not require ifdefs for sections using these defines. This code is needed for the following fix to set the SRAM size correctly for HS omaps. Also at least PM and watchdog code will need this function. Signed-off-by: Kevin Hilman Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/id.c | 22 ++++++++++++++++++++++ arch/arm/plat-omap/include/mach/cpu.h | 22 +++++++++++----------- 2 files changed, 33 insertions(+), 11 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/id.c b/arch/arm/mach-omap2/id.c index 458990e20c6..a98201cc265 100644 --- a/arch/arm/mach-omap2/id.c +++ b/arch/arm/mach-omap2/id.c @@ -48,6 +48,28 @@ int omap_chip_is(struct omap_chip_id oci) } EXPORT_SYMBOL(omap_chip_is); +int omap_type(void) +{ + u32 val = 0; + + if (cpu_is_omap24xx()) + val = omap_ctrl_readl(OMAP24XX_CONTROL_STATUS); + else if (cpu_is_omap34xx()) + val = omap_ctrl_readl(OMAP343X_CONTROL_STATUS); + else { + pr_err("Cannot detect omap type!\n"); + goto out; + } + + val &= OMAP2_DEVICETYPE_MASK; + val >>= 8; + +out: + return val; +} +EXPORT_SYMBOL(omap_type); + + /*----------------------------------------------------------------------------*/ #define OMAP_TAP_IDCODE 0x0204 diff --git a/arch/arm/plat-omap/include/mach/cpu.h b/arch/arm/plat-omap/include/mach/cpu.h index fc60c4ebcc2..285eaa3a827 100644 --- a/arch/arm/plat-omap/include/mach/cpu.h +++ b/arch/arm/plat-omap/include/mach/cpu.h @@ -30,6 +30,17 @@ #ifndef __ASM_ARCH_OMAP_CPU_H #define __ASM_ARCH_OMAP_CPU_H +/* + * Omap device type i.e. EMU/HS/TST/GP/BAD + */ +#define OMAP2_DEVICE_TYPE_TEST 0 +#define OMAP2_DEVICE_TYPE_EMU 1 +#define OMAP2_DEVICE_TYPE_SEC 2 +#define OMAP2_DEVICE_TYPE_GP 3 +#define OMAP2_DEVICE_TYPE_BAD 4 + +int omap_type(void); + struct omap_chip_id { u8 oc; u8 type; @@ -424,17 +435,6 @@ IS_OMAP_TYPE(3430, 0x3430) int omap_chip_is(struct omap_chip_id oci); -int omap_type(void); - -/* - * Macro to detect device type i.e. EMU/HS/TST/GP/BAD - */ -#define OMAP2_DEVICE_TYPE_TEST 0 -#define OMAP2_DEVICE_TYPE_EMU 1 -#define OMAP2_DEVICE_TYPE_SEC 2 -#define OMAP2_DEVICE_TYPE_GP 3 -#define OMAP2_DEVICE_TYPE_BAD 4 - void omap2_check_revision(void); #endif /* defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) */ -- cgit v1.2.3-70-g09d2 From 6d453e84b587f38e4197bb2c6a37296c4a80cbac Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Tue, 23 Jun 2009 13:30:24 +0300 Subject: OMAP2/3: gpmc-onenand: correct use of async timings Use async timings when sync timings are not requested. Also ensure that OneNAND is in async mode when async timings are used. Signed-off-by: Adrian Hunter Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/gpmc-onenand.c | 21 +++++++++++++++++++-- 1 file changed, 19 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/gpmc-onenand.c b/arch/arm/mach-omap2/gpmc-onenand.c index 2fd22f9c5f0..54fec53a48e 100644 --- a/arch/arm/mach-omap2/gpmc-onenand.c +++ b/arch/arm/mach-omap2/gpmc-onenand.c @@ -31,6 +31,8 @@ static struct platform_device gpmc_onenand_device = { static int omap2_onenand_set_async_mode(int cs, void __iomem *onenand_base) { struct gpmc_timings t; + u32 reg; + int err; const int t_cer = 15; const int t_avdp = 12; @@ -43,6 +45,11 @@ static int omap2_onenand_set_async_mode(int cs, void __iomem *onenand_base) const int t_wpl = 40; const int t_wph = 30; + /* Ensure sync read and sync write are disabled */ + reg = readw(onenand_base + ONENAND_REG_SYS_CFG1); + reg &= ~ONENAND_SYS_CFG1_SYNC_READ & ~ONENAND_SYS_CFG1_SYNC_WRITE; + writew(reg, onenand_base + ONENAND_REG_SYS_CFG1); + memset(&t, 0, sizeof(t)); t.sync_clk = 0; t.cs_on = 0; @@ -74,7 +81,16 @@ static int omap2_onenand_set_async_mode(int cs, void __iomem *onenand_base) GPMC_CONFIG1_DEVICESIZE_16 | GPMC_CONFIG1_MUXADDDATA); - return gpmc_cs_set_timings(cs, &t); + err = gpmc_cs_set_timings(cs, &t); + if (err) + return err; + + /* Ensure sync read and sync write are disabled */ + reg = readw(onenand_base + ONENAND_REG_SYS_CFG1); + reg &= ~ONENAND_SYS_CFG1_SYNC_READ & ~ONENAND_SYS_CFG1_SYNC_WRITE; + writew(reg, onenand_base + ONENAND_REG_SYS_CFG1); + + return 0; } static void set_onenand_cfg(void __iomem *onenand_base, int latency, @@ -124,7 +140,8 @@ static int omap2_onenand_set_sync_mode(struct omap_onenand_platform_data *cfg, } else if (cfg->flags & ONENAND_SYNC_READWRITE) { sync_read = 1; sync_write = 1; - } + } else + return omap2_onenand_set_async_mode(cs, onenand_base); if (!freq) { /* Very first call freq is not known */ -- cgit v1.2.3-70-g09d2 From c8e6488f7b56d82453fc7d526118e9f1c2df133a Mon Sep 17 00:00:00 2001 From: Adrian Hunter Date: Tue, 23 Jun 2009 13:30:25 +0300 Subject: OMAP3: RX51: Use OneNAND sync read / write Use OneNAND sync read / write Signed-off-by: Adrian Hunter Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-rx51-peripherals.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index da93b86234e..9a0bf6744a0 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -362,6 +362,7 @@ static struct omap_onenand_platform_data board_onenand_data = { .gpio_irq = 65, .parts = onenand_partitions, .nr_parts = ARRAY_SIZE(onenand_partitions), + .flags = ONENAND_SYNC_READWRITE, }; static void __init board_onenand_init(void) -- cgit v1.2.3-70-g09d2 From 58cda884ecc87dcce18d463b0c8bd928dae63ad8 Mon Sep 17 00:00:00 2001 From: Jean Pihet Date: Fri, 24 Jul 2009 19:43:25 -0600 Subject: OMAP3 SDRC: add support for 2 SDRAM chip selects Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2 SDRAM parts connected to the SDRC. This patch adds the following: - add a new argument of type omap_sdrc_params struct* to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params - adapted the OMAP boards files to the new prototype of omap2_init_common_hw - add the SDRC 2nd CS registers offsets defines - adapt the sram sleep code to configure the SDRC for the 2nd CS Note: If the 2nd param to omap2_init_common_hw is NULL, then the parameters are not programmed into the SDRC CS1 registers Tested on 3430 SDP and Beagleboard rev C2 and B5, with suspend/resume and frequency changes (cpufreq). Signed-off-by: Jean Pihet Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/board-2430sdp.c | 2 +- arch/arm/mach-omap2/board-3430sdp.c | 2 +- arch/arm/mach-omap2/board-4430sdp.c | 2 +- arch/arm/mach-omap2/board-apollon.c | 2 +- arch/arm/mach-omap2/board-generic.c | 2 +- arch/arm/mach-omap2/board-h4.c | 2 +- arch/arm/mach-omap2/board-ldp.c | 2 +- arch/arm/mach-omap2/board-omap3beagle.c | 3 +- arch/arm/mach-omap2/board-omap3evm.c | 2 +- arch/arm/mach-omap2/board-omap3pandora.c | 3 +- arch/arm/mach-omap2/board-overo.c | 3 +- arch/arm/mach-omap2/board-rx51.c | 2 +- arch/arm/mach-omap2/board-zoom2.c | 2 +- arch/arm/mach-omap2/clock34xx.c | 37 +++++++-- arch/arm/mach-omap2/io.c | 5 +- arch/arm/mach-omap2/sdrc.c | 63 +++++++++----- arch/arm/mach-omap2/sram34xx.S | 137 ++++++++++++++++++++++++------- arch/arm/plat-omap/include/mach/io.h | 3 +- arch/arm/plat-omap/include/mach/sdrc.h | 11 ++- arch/arm/plat-omap/include/mach/sram.h | 23 +++--- arch/arm/plat-omap/sram.c | 30 ++++--- 21 files changed, 236 insertions(+), 102 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c index 9c3fdcdf76c..8ec2a132904 100644 --- a/arch/arm/mach-omap2/board-2430sdp.c +++ b/arch/arm/mach-omap2/board-2430sdp.c @@ -141,7 +141,7 @@ static inline void board_smc91x_init(void) static void __init omap_2430sdp_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c index 496a90e4ea7..ac262cd7450 100644 --- a/arch/arm/mach-omap2/board-3430sdp.c +++ b/arch/arm/mach-omap2/board-3430sdp.c @@ -169,7 +169,7 @@ static struct platform_device *sdp3430_devices[] __initdata = { static void __init omap_3430sdp_init_irq(void) { - omap2_init_common_hw(hyb18m512160af6_sdrc_params); + omap2_init_common_hw(hyb18m512160af6_sdrc_params, NULL); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-4430sdp.c b/arch/arm/mach-omap2/board-4430sdp.c index 57e477bd89c..b0c7402248f 100644 --- a/arch/arm/mach-omap2/board-4430sdp.c +++ b/arch/arm/mach-omap2/board-4430sdp.c @@ -59,7 +59,7 @@ static void __init gic_init_irq(void) static void __init omap_4430sdp_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); #ifdef CONFIG_OMAP_32K_TIMER omap2_gp_clockevent_set_gptimer(1); #endif diff --git a/arch/arm/mach-omap2/board-apollon.c b/arch/arm/mach-omap2/board-apollon.c index 06dfba888b0..dcfc20d0389 100644 --- a/arch/arm/mach-omap2/board-apollon.c +++ b/arch/arm/mach-omap2/board-apollon.c @@ -250,7 +250,7 @@ out: static void __init omap_apollon_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); apollon_init_smc91x(); diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c index 3492162a65c..fd00aa03690 100644 --- a/arch/arm/mach-omap2/board-generic.c +++ b/arch/arm/mach-omap2/board-generic.c @@ -33,7 +33,7 @@ static void __init omap_generic_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); } diff --git a/arch/arm/mach-omap2/board-h4.c b/arch/arm/mach-omap2/board-h4.c index e7d017cdc43..7b1d61d5bb2 100644 --- a/arch/arm/mach-omap2/board-h4.c +++ b/arch/arm/mach-omap2/board-h4.c @@ -270,7 +270,7 @@ static void __init h4_init_flash(void) static void __init omap_h4_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); h4_init_flash(); diff --git a/arch/arm/mach-omap2/board-ldp.c b/arch/arm/mach-omap2/board-ldp.c index d8bc0a7dcb8..ea383f88cb1 100644 --- a/arch/arm/mach-omap2/board-ldp.c +++ b/arch/arm/mach-omap2/board-ldp.c @@ -270,7 +270,7 @@ static inline void __init ldp_init_smsc911x(void) static void __init omap_ldp_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); ldp_init_smsc911x(); diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 991ac9c3803..4abefd9566e 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -282,7 +282,8 @@ static int __init omap3_beagle_i2c_init(void) static void __init omap3_beagle_init_irq(void) { - omap2_init_common_hw(mt46h32m32lf6_sdrc_params); + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, + mt46h32m32lf6_sdrc_params); omap_init_irq(); #ifdef CONFIG_OMAP_32K_TIMER omap2_gp_clockevent_set_gptimer(12); diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index d3cc145814d..217e5a2861d 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -279,7 +279,7 @@ struct spi_board_info omap3evm_spi_board_info[] = { static void __init omap3_evm_init_irq(void) { - omap2_init_common_hw(mt46h32m32lf6_sdrc_params); + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, NULL); omap_init_irq(); omap_gpio_init(); omap3evm_init_smc911x(); diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index e32aa23ce96..9b991ced382 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -310,7 +310,8 @@ static int __init omap3pandora_i2c_init(void) static void __init omap3pandora_init_irq(void) { - omap2_init_common_hw(mt46h32m32lf6_sdrc_params); + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, + mt46h32m32lf6_sdrc_params); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index dff5528fbfb..44bc1c54cd0 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -360,7 +360,8 @@ static int __init overo_i2c_init(void) static void __init overo_init_irq(void) { - omap2_init_common_hw(mt46h32m32lf6_sdrc_params); + omap2_init_common_hw(mt46h32m32lf6_sdrc_params, + mt46h32m32lf6_sdrc_params); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c index 374ff63c3eb..591ae8a5805 100644 --- a/arch/arm/mach-omap2/board-rx51.c +++ b/arch/arm/mach-omap2/board-rx51.c @@ -61,7 +61,7 @@ static struct omap_board_config_kernel rx51_config[] = { static void __init rx51_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/board-zoom2.c b/arch/arm/mach-omap2/board-zoom2.c index bcc0f7632de..427b7b8b123 100644 --- a/arch/arm/mach-omap2/board-zoom2.c +++ b/arch/arm/mach-omap2/board-zoom2.c @@ -25,7 +25,7 @@ static void __init omap_zoom2_init_irq(void) { - omap2_init_common_hw(NULL); + omap2_init_common_hw(NULL, NULL); omap_init_irq(); omap_gpio_init(); } diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index 045da923e75..1c6480d3ad6 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -725,7 +725,9 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) u32 unlock_dll = 0; u32 c; unsigned long validrate, sdrcrate, mpurate; - struct omap_sdrc_params *sp; + struct omap_sdrc_params *sdrc_cs0; + struct omap_sdrc_params *sdrc_cs1; + int ret; if (!clk || !rate) return -EINVAL; @@ -743,8 +745,8 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) else sdrcrate >>= ((clk->rate / rate) >> 1); - sp = omap2_sdrc_get_params(sdrcrate); - if (!sp) + ret = omap2_sdrc_get_params(sdrcrate, &sdrc_cs0, &sdrc_cs1); + if (ret) return -EINVAL; if (sdrcrate < MIN_SDRC_DLL_LOCK_FREQ) { @@ -765,12 +767,29 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate) pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate, validrate); - pr_debug("clock: SDRC timing params used: %08x %08x %08x\n", - sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb); - - omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla, - sp->actim_ctrlb, new_div, unlock_dll, c, - sp->mr, rate > clk->rate); + pr_debug("clock: SDRC CS0 timing params used:" + " RFR %08x CTRLA %08x CTRLB %08x MR %08x\n", + sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla, + sdrc_cs0->actim_ctrlb, sdrc_cs0->mr); + if (sdrc_cs1) + pr_debug("clock: SDRC CS1 timing params used: " + " RFR %08x CTRLA %08x CTRLB %08x MR %08x\n", + sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla, + sdrc_cs1->actim_ctrlb, sdrc_cs1->mr); + + if (sdrc_cs1) + omap3_configure_core_dpll( + new_div, unlock_dll, c, rate > clk->rate, + sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla, + sdrc_cs0->actim_ctrlb, sdrc_cs0->mr, + sdrc_cs1->rfr_ctrl, sdrc_cs1->actim_ctrla, + sdrc_cs1->actim_ctrlb, sdrc_cs1->mr); + else + omap3_configure_core_dpll( + new_div, unlock_dll, c, rate > clk->rate, + sdrc_cs0->rfr_ctrl, sdrc_cs0->actim_ctrla, + sdrc_cs0->actim_ctrlb, sdrc_cs0->mr, + 0, 0, 0, 0); return 0; } diff --git a/arch/arm/mach-omap2/io.c b/arch/arm/mach-omap2/io.c index 3a86b0f6603..e9b9bcb19b4 100644 --- a/arch/arm/mach-omap2/io.c +++ b/arch/arm/mach-omap2/io.c @@ -276,14 +276,15 @@ static int __init _omap2_init_reprogram_sdrc(void) return v; } -void __init omap2_init_common_hw(struct omap_sdrc_params *sp) +void __init omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0, + struct omap_sdrc_params *sdrc_cs1) { omap2_mux_init(); #ifndef CONFIG_ARCH_OMAP4 /* FIXME: Remove this once the clkdev is ready */ pwrdm_init(powerdomains_omap); clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps); omap2_clk_init(); - omap2_sdrc_init(sp); + omap2_sdrc_init(sdrc_cs0, sdrc_cs1); _omap2_init_reprogram_sdrc(); #endif gpmc_init(); diff --git a/arch/arm/mach-omap2/sdrc.c b/arch/arm/mach-omap2/sdrc.c index 2045441e838..2e9e38db30e 100644 --- a/arch/arm/mach-omap2/sdrc.c +++ b/arch/arm/mach-omap2/sdrc.c @@ -32,7 +32,7 @@ #include #include "sdrc.h" -static struct omap_sdrc_params *sdrc_init_params; +static struct omap_sdrc_params *sdrc_init_params_cs0, *sdrc_init_params_cs1; void __iomem *omap2_sdrc_base; void __iomem *omap2_sms_base; @@ -45,33 +45,49 @@ void __iomem *omap2_sms_base; /** * omap2_sdrc_get_params - return SDRC register values for a given clock rate * @r: SDRC clock rate (in Hz) + * @sdrc_cs0: chip select 0 ram timings ** + * @sdrc_cs1: chip select 1 ram timings ** * * Return pre-calculated values for the SDRC_ACTIM_CTRLA, - * SDRC_ACTIM_CTRLB, SDRC_RFR_CTRL, and SDRC_MR registers, for a given - * SDRC clock rate 'r'. These parameters control various timing - * delays in the SDRAM controller that are expressed in terms of the - * number of SDRC clock cycles to wait; hence the clock rate - * dependency. Note that sdrc_init_params must be sorted rate - * descending. Also assumes that both chip-selects use the same - * timing parameters. Returns a struct omap_sdrc_params * upon - * success, or NULL upon failure. + * SDRC_ACTIM_CTRLB, SDRC_RFR_CTRL and SDRC_MR registers in sdrc_cs[01] + * structs,for a given SDRC clock rate 'r'. + * These parameters control various timing delays in the SDRAM controller + * that are expressed in terms of the number of SDRC clock cycles to + * wait; hence the clock rate dependency. + * + * Supports 2 different timing parameters for both chip selects. + * + * Note 1: the sdrc_init_params_cs[01] must be sorted rate descending. + * Note 2: If sdrc_init_params_cs_1 is not NULL it must be of same size + * as sdrc_init_params_cs_0. + * + * Fills in the struct omap_sdrc_params * for each chip select. + * Returns 0 upon success or -1 upon failure. */ -struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r) +int omap2_sdrc_get_params(unsigned long r, + struct omap_sdrc_params **sdrc_cs0, + struct omap_sdrc_params **sdrc_cs1) { - struct omap_sdrc_params *sp; + struct omap_sdrc_params *sp0, *sp1; - if (!sdrc_init_params) - return NULL; + if (!sdrc_init_params_cs0) + return -1; - sp = sdrc_init_params; + sp0 = sdrc_init_params_cs0; + sp1 = sdrc_init_params_cs1; - while (sp->rate && sp->rate != r) - sp++; + while (sp0->rate && sp0->rate != r) { + sp0++; + if (sdrc_init_params_cs1) + sp1++; + } - if (!sp->rate) - return NULL; + if (!sp0->rate) + return -1; - return sp; + *sdrc_cs0 = sp0; + *sdrc_cs1 = sp1; + return 0; } @@ -83,13 +99,15 @@ void __init omap2_set_globals_sdrc(struct omap_globals *omap2_globals) /** * omap2_sdrc_init - initialize SMS, SDRC devices on boot - * @sp: pointer to a null-terminated list of struct omap_sdrc_params + * @sdrc_cs[01]: pointers to a null-terminated list of struct omap_sdrc_params + * Support for 2 chip selects timings * * Turn on smart idle modes for SDRAM scheduler and controller. * Program a known-good configuration for the SDRC to deal with buggy * bootloaders. */ -void __init omap2_sdrc_init(struct omap_sdrc_params *sp) +void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0, + struct omap_sdrc_params *sdrc_cs1) { u32 l; @@ -103,7 +121,8 @@ void __init omap2_sdrc_init(struct omap_sdrc_params *sp) l |= (0x2 << 3); sdrc_write_reg(l, SDRC_SYSCONFIG); - sdrc_init_params = sp; + sdrc_init_params_cs0 = sdrc_cs0; + sdrc_init_params_cs1 = sdrc_cs1; /* XXX Enable SRFRONIDLEREQ here also? */ l = (1 << SDRC_POWER_EXTCLKDIS_SHIFT) | diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index f41f8d96ddb..3aef7448b2a 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -36,7 +36,7 @@ .text -/* r4 parameters */ +/* r1 parameters */ #define SDRC_NO_UNLOCK_DLL 0x0 #define SDRC_UNLOCK_DLL 0x1 @@ -71,40 +71,71 @@ /* * omap3_sram_configure_core_dpll - change DPLL3 M2 divider - * r0 = new SDRC_RFR_CTRL register contents - * r1 = new SDRC_ACTIM_CTRLA register contents - * r2 = new SDRC_ACTIM_CTRLB register contents - * r3 = new M2 divider setting (only 1 and 2 supported right now) - * r4 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for + * + * Params passed in registers: + * r0 = new M2 divider setting (only 1 and 2 supported right now) + * r1 = unlock SDRC DLL? (1 = yes, 0 = no). Only unlock DLL for * SDRC rates < 83MHz - * r5 = number of MPU cycles to wait for SDRC to stabilize after + * r2 = number of MPU cycles to wait for SDRC to stabilize after * reprogramming the SDRC when switching to a slower MPU speed - * r6 = new SDRC_MR_0 register value - * r7 = increasing SDRC rate? (1 = yes, 0 = no) + * r3 = increasing SDRC rate? (1 = yes, 0 = no) + * + * Params passed via the stack. The needed params will be copied in SRAM + * before use by the code in SRAM (SDRAM is not accessible during SDRC + * reconfiguration): + * new SDRC_RFR_CTRL_0 register contents + * new SDRC_ACTIM_CTRL_A_0 register contents + * new SDRC_ACTIM_CTRL_B_0 register contents + * new SDRC_MR_0 register value + * new SDRC_RFR_CTRL_1 register contents + * new SDRC_ACTIM_CTRL_A_1 register contents + * new SDRC_ACTIM_CTRL_B_1 register contents + * new SDRC_MR_1 register value * + * If the param SDRC_RFR_CTRL_1 is 0, the parameters + * are not programmed into the SDRC CS1 registers */ ENTRY(omap3_sram_configure_core_dpll) stmfd sp!, {r1-r12, lr} @ store regs to stack - ldr r4, [sp, #52] @ pull extra args off the stack - ldr r5, [sp, #56] @ load extra args from the stack - ldr r6, [sp, #60] @ load extra args from the stack - ldr r7, [sp, #64] @ load extra args from the stack + + @ pull the extra args off the stack + @ and store them in SRAM + ldr r4, [sp, #52] + str r4, omap_sdrc_rfr_ctrl_0_val + ldr r4, [sp, #56] + str r4, omap_sdrc_actim_ctrl_a_0_val + ldr r4, [sp, #60] + str r4, omap_sdrc_actim_ctrl_b_0_val + ldr r4, [sp, #64] + str r4, omap_sdrc_mr_0_val + ldr r4, [sp, #68] + str r4, omap_sdrc_rfr_ctrl_1_val + cmp r4, #0 @ if SDRC_RFR_CTRL_1 is 0, + beq skip_cs1_params @ do not use cs1 params + ldr r4, [sp, #72] + str r4, omap_sdrc_actim_ctrl_a_1_val + ldr r4, [sp, #76] + str r4, omap_sdrc_actim_ctrl_b_1_val + ldr r4, [sp, #80] + str r4, omap_sdrc_mr_1_val +skip_cs1_params: dsb @ flush buffered writes to interconnect - cmp r7, #1 @ if increasing SDRC clk rate, + + cmp r3, #1 @ if increasing SDRC clk rate, bleq configure_sdrc @ program the SDRC regs early (for RFR) - cmp r4, #SDRC_UNLOCK_DLL @ set the intended DLL state + cmp r1, #SDRC_UNLOCK_DLL @ set the intended DLL state bleq unlock_dll blne lock_dll bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC bl configure_core_dpll @ change the DPLL3 M2 divider bl enable_sdrc @ take SDRC out of idle - cmp r4, #SDRC_UNLOCK_DLL @ wait for DLL status to change + cmp r1, #SDRC_UNLOCK_DLL @ wait for DLL status to change bleq wait_dll_unlock blne wait_dll_lock - cmp r7, #1 @ if increasing SDRC clk rate, + cmp r3, #1 @ if increasing SDRC clk rate, beq return_to_sdram @ return to SDRAM code, otherwise, bl configure_sdrc @ reprogram SDRC regs now - mov r12, r5 + mov r12, r2 bl wait_clk_stable @ wait for SDRC to stabilize return_to_sdram: isb @ prevent speculative exec past here @@ -149,7 +180,7 @@ configure_core_dpll: ldr r12, [r11] ldr r10, core_m2_mask_val @ modify m2 for core dpll and r12, r12, r10 - orr r12, r12, r3, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT + orr r12, r12, r0, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT str r12, [r11] ldr r12, [r11] @ posted-write barrier for CM bx lr @@ -187,15 +218,34 @@ wait_dll_unlock: bne wait_dll_unlock bx lr configure_sdrc: - ldr r11, omap3_sdrc_rfr_ctrl - str r0, [r11] - ldr r11, omap3_sdrc_actim_ctrla - str r1, [r11] - ldr r11, omap3_sdrc_actim_ctrlb - str r2, [r11] + ldr r12, omap_sdrc_rfr_ctrl_0_val @ fetch value from SRAM + ldr r11, omap3_sdrc_rfr_ctrl_0 @ fetch addr from SRAM + str r12, [r11] @ store + ldr r12, omap_sdrc_actim_ctrl_a_0_val + ldr r11, omap3_sdrc_actim_ctrl_a_0 + str r12, [r11] + ldr r12, omap_sdrc_actim_ctrl_b_0_val + ldr r11, omap3_sdrc_actim_ctrl_b_0 + str r12, [r11] + ldr r12, omap_sdrc_mr_0_val ldr r11, omap3_sdrc_mr_0 - str r6, [r11] - ldr r6, [r11] @ posted-write barrier for SDRC + str r12, [r11] + ldr r12, omap_sdrc_rfr_ctrl_1_val + cmp r12, #0 @ if SDRC_RFR_CTRL_1 is 0, + beq skip_cs1_prog @ do not program cs1 params + ldr r11, omap3_sdrc_rfr_ctrl_1 + str r12, [r11] + ldr r12, omap_sdrc_actim_ctrl_a_1_val + ldr r11, omap3_sdrc_actim_ctrl_a_1 + str r12, [r11] + ldr r12, omap_sdrc_actim_ctrl_b_1_val + ldr r11, omap3_sdrc_actim_ctrl_b_1 + str r12, [r11] + ldr r12, omap_sdrc_mr_1_val + ldr r11, omap3_sdrc_mr_1 + str r12, [r11] +skip_cs1_prog: + ldr r12, [r11] @ posted-write barrier for SDRC bx lr omap3_sdrc_power: @@ -206,14 +256,40 @@ omap3_cm_idlest1_core: .word OMAP34XX_CM_REGADDR(CORE_MOD, CM_IDLEST) omap3_cm_iclken1_core: .word OMAP34XX_CM_REGADDR(CORE_MOD, CM_ICLKEN1) -omap3_sdrc_rfr_ctrl: + +omap3_sdrc_rfr_ctrl_0: .word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_0) -omap3_sdrc_actim_ctrla: +omap3_sdrc_rfr_ctrl_1: + .word OMAP34XX_SDRC_REGADDR(SDRC_RFR_CTRL_1) +omap3_sdrc_actim_ctrl_a_0: .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0) -omap3_sdrc_actim_ctrlb: +omap3_sdrc_actim_ctrl_a_1: + .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_1) +omap3_sdrc_actim_ctrl_b_0: .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0) +omap3_sdrc_actim_ctrl_b_1: + .word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_1) omap3_sdrc_mr_0: .word OMAP34XX_SDRC_REGADDR(SDRC_MR_0) +omap3_sdrc_mr_1: + .word OMAP34XX_SDRC_REGADDR(SDRC_MR_1) +omap_sdrc_rfr_ctrl_0_val: + .word 0xDEADBEEF +omap_sdrc_rfr_ctrl_1_val: + .word 0xDEADBEEF +omap_sdrc_actim_ctrl_a_0_val: + .word 0xDEADBEEF +omap_sdrc_actim_ctrl_a_1_val: + .word 0xDEADBEEF +omap_sdrc_actim_ctrl_b_0_val: + .word 0xDEADBEEF +omap_sdrc_actim_ctrl_b_1_val: + .word 0xDEADBEEF +omap_sdrc_mr_0_val: + .word 0xDEADBEEF +omap_sdrc_mr_1_val: + .word 0xDEADBEEF + omap3_sdrc_dlla_status: .word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS) omap3_sdrc_dlla_ctrl: @@ -223,3 +299,4 @@ core_m2_mask_val: ENTRY(omap3_sram_configure_core_dpll_sz) .word . - omap3_sram_configure_core_dpll + diff --git a/arch/arm/plat-omap/include/mach/io.h b/arch/arm/plat-omap/include/mach/io.h index 73f483d56ca..21fb0efdda8 100644 --- a/arch/arm/plat-omap/include/mach/io.h +++ b/arch/arm/plat-omap/include/mach/io.h @@ -228,7 +228,8 @@ extern void omap1_map_common_io(void); extern void omap1_init_common_hw(void); extern void omap2_map_common_io(void); -extern void omap2_init_common_hw(struct omap_sdrc_params *sp); +extern void omap2_init_common_hw(struct omap_sdrc_params *sdrc_cs0, + struct omap_sdrc_params *sdrc_cs1); #define __arch_ioremap(p,s,t) omap_ioremap(p,s,t) #define __arch_iounmap(v) omap_iounmap(v) diff --git a/arch/arm/plat-omap/include/mach/sdrc.h b/arch/arm/plat-omap/include/mach/sdrc.h index adc73522491..0be18e4ff18 100644 --- a/arch/arm/plat-omap/include/mach/sdrc.h +++ b/arch/arm/plat-omap/include/mach/sdrc.h @@ -30,6 +30,10 @@ #define SDRC_ACTIM_CTRL_A_0 0x09c #define SDRC_ACTIM_CTRL_B_0 0x0a0 #define SDRC_RFR_CTRL_0 0x0a4 +#define SDRC_MR_1 0x0B4 +#define SDRC_ACTIM_CTRL_A_1 0x0C4 +#define SDRC_ACTIM_CTRL_B_1 0x0C8 +#define SDRC_RFR_CTRL_1 0x0D4 /* * These values represent the number of memory clock cycles between @@ -102,8 +106,11 @@ struct omap_sdrc_params { u32 mr; }; -void __init omap2_sdrc_init(struct omap_sdrc_params *sp); -struct omap_sdrc_params *omap2_sdrc_get_params(unsigned long r); +void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0, + struct omap_sdrc_params *sdrc_cs1); +int omap2_sdrc_get_params(unsigned long r, + struct omap_sdrc_params **sdrc_cs0, + struct omap_sdrc_params **sdrc_cs1); #ifdef CONFIG_ARCH_OMAP2 diff --git a/arch/arm/plat-omap/include/mach/sram.h b/arch/arm/plat-omap/include/mach/sram.h index 4d53cc59d7a..8974e3fc269 100644 --- a/arch/arm/plat-omap/include/mach/sram.h +++ b/arch/arm/plat-omap/include/mach/sram.h @@ -21,11 +21,12 @@ extern void omap2_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, u32 mem_type); extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass); -extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, - u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll, u32 f, u32 sdrc_mr, - u32 inc); +extern u32 omap3_configure_core_dpll( + u32 m2, u32 unlock_dll, u32 f, u32 inc, + u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0, + u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0, + u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1, + u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1); /* Do not use these */ extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl); @@ -59,12 +60,12 @@ extern void omap243x_sram_reprogram_sdrc(u32 perf_level, u32 dll_val, u32 mem_type); extern unsigned long omap243x_sram_reprogram_sdrc_sz; - -extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl, - u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, u32 m2, - u32 unlock_dll, u32 f, u32 sdrc_mr, - u32 inc); +extern u32 omap3_sram_configure_core_dpll( + u32 m2, u32 unlock_dll, u32 f, u32 inc, + u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0, + u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0, + u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1, + u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1); extern unsigned long omap3_sram_configure_core_dpll_sz; #endif diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c index 4ea73804d21..4e781c99f0e 100644 --- a/arch/arm/plat-omap/sram.c +++ b/arch/arm/plat-omap/sram.c @@ -373,20 +373,26 @@ static inline int omap243x_sram_init(void) #ifdef CONFIG_ARCH_OMAP3 -static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl, - u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, - u32 m2, u32 unlock_dll, - u32 f, u32 sdrc_mr, u32 inc); -u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla, - u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll, - u32 f, u32 sdrc_mr, u32 inc) +static u32 (*_omap3_sram_configure_core_dpll)( + u32 m2, u32 unlock_dll, u32 f, u32 inc, + u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0, + u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0, + u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1, + u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1); + +u32 omap3_configure_core_dpll(u32 m2, u32 unlock_dll, u32 f, u32 inc, + u32 sdrc_rfr_ctrl_0, u32 sdrc_actim_ctrl_a_0, + u32 sdrc_actim_ctrl_b_0, u32 sdrc_mr_0, + u32 sdrc_rfr_ctrl_1, u32 sdrc_actim_ctrl_a_1, + u32 sdrc_actim_ctrl_b_1, u32 sdrc_mr_1) { BUG_ON(!_omap3_sram_configure_core_dpll); - return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl, - sdrc_actim_ctrla, - sdrc_actim_ctrlb, m2, - unlock_dll, f, sdrc_mr, inc); + return _omap3_sram_configure_core_dpll( + m2, unlock_dll, f, inc, + sdrc_rfr_ctrl_0, sdrc_actim_ctrl_a_0, + sdrc_actim_ctrl_b_0, sdrc_mr_0, + sdrc_rfr_ctrl_1, sdrc_actim_ctrl_a_1, + sdrc_actim_ctrl_b_1, sdrc_mr_1); } /* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */ -- cgit v1.2.3-70-g09d2 From 9fb97412c3be5d0d1dd0e9d7c5268469e4c942aa Mon Sep 17 00:00:00 2001 From: Jean Pihet Date: Fri, 24 Jul 2009 19:43:25 -0600 Subject: OMAP3: Setup MUX settings for SDRC CKE signals This patches ensures the MUX settings are correct for the SDRC CKE signals to SDRAM. This allows the self-refresh to work when 2 chip-selects are in use. A warning is thrown away in case the initial muxing is incorrect, in order to track faulty or old-dated bootloaders. Note: The CONFIG_OMAP_MUX and CONFIG_OMAP_MUX_WARNINGS options must be enabled for the mux code to have effect. Signed-off-by: Jean Pihet Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/board-omap3beagle.c | 4 ++++ arch/arm/mach-omap2/board-omap3pandora.c | 5 +++++ arch/arm/mach-omap2/board-overo.c | 5 +++++ arch/arm/mach-omap2/board-rx51.c | 4 ++++ arch/arm/mach-omap2/mux.c | 6 ++++++ arch/arm/plat-omap/include/mach/mux.h | 4 ++++ 6 files changed, 28 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index 4abefd9566e..e00ba128cec 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -409,6 +409,10 @@ static void __init omap3_beagle_init(void) usb_musb_init(); omap3beagle_flash_init(); + + /* Ensure SDRC pins are mux'd for self-refresh */ + omap_cfg_reg(H16_34XX_SDRC_CKE0); + omap_cfg_reg(H17_34XX_SDRC_CKE1); } static void __init omap3_beagle_map_io(void) diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index 9b991ced382..864ee3d021f 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -40,6 +40,7 @@ #include #include #include +#include #include "sdram-micron-mt46h32m32lf-6.h" #include "mmc-twl4030.h" @@ -398,6 +399,10 @@ static void __init omap3pandora_init(void) omap3pandora_ads7846_init(); pandora_keys_gpio_init(); usb_musb_init(); + + /* Ensure SDRC pins are mux'd for self-refresh */ + omap_cfg_reg(H16_34XX_SDRC_CKE0); + omap_cfg_reg(H17_34XX_SDRC_CKE1); } static void __init omap3pandora_map_io(void) diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index 44bc1c54cd0..6b171b338ec 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -44,6 +44,7 @@ #include #include #include +#include #include #include "sdram-micron-mt46h32m32lf-6.h" @@ -396,6 +397,10 @@ static void __init overo_init(void) overo_ads7846_init(); overo_init_smsc911x(); + /* Ensure SDRC pins are mux'd for self-refresh */ + omap_cfg_reg(H16_34XX_SDRC_CKE0); + omap_cfg_reg(H17_34XX_SDRC_CKE1); + if ((gpio_request(OVERO_GPIO_W2W_NRESET, "OVERO_GPIO_W2W_NRESET") == 0) && (gpio_direction_output(OVERO_GPIO_W2W_NRESET, 1) == 0)) { diff --git a/arch/arm/mach-omap2/board-rx51.c b/arch/arm/mach-omap2/board-rx51.c index 591ae8a5805..1c9e07fe826 100644 --- a/arch/arm/mach-omap2/board-rx51.c +++ b/arch/arm/mach-omap2/board-rx51.c @@ -75,6 +75,10 @@ static void __init rx51_init(void) omap_serial_init(); usb_musb_init(); rx51_peripherals_init(); + + /* Ensure SDRC pins are mux'd for self-refresh */ + omap_cfg_reg(H16_34XX_SDRC_CKE0); + omap_cfg_reg(H17_34XX_SDRC_CKE1); } static void __init rx51_map_io(void) diff --git a/arch/arm/mach-omap2/mux.c b/arch/arm/mach-omap2/mux.c index 026c4fc883a..43d6b92b65f 100644 --- a/arch/arm/mach-omap2/mux.c +++ b/arch/arm/mach-omap2/mux.c @@ -486,6 +486,12 @@ MUX_CFG_34XX("H19_34XX_GPIO164_OUT", 0x19c, OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_OUTPUT) MUX_CFG_34XX("J25_34XX_GPIO170", 0x1c6, OMAP34XX_MUX_MODE4 | OMAP34XX_PIN_INPUT) + +/* OMAP3 SDRC CKE signals to SDR/DDR ram chips */ +MUX_CFG_34XX("H16_34XX_SDRC_CKE0", 0x262, + OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT) +MUX_CFG_34XX("H17_34XX_SDRC_CKE1", 0x264, + OMAP34XX_MUX_MODE0 | OMAP34XX_PIN_OUTPUT) }; #define OMAP34XX_PINS_SZ ARRAY_SIZE(omap34xx_pins) diff --git a/arch/arm/plat-omap/include/mach/mux.h b/arch/arm/plat-omap/include/mach/mux.h index 85a62170576..80281c458ba 100644 --- a/arch/arm/plat-omap/include/mach/mux.h +++ b/arch/arm/plat-omap/include/mach/mux.h @@ -853,6 +853,10 @@ enum omap34xx_index { AE5_34XX_GPIO143, H19_34XX_GPIO164_OUT, J25_34XX_GPIO170, + + /* OMAP3 SDRC CKE signals to SDR/DDR ram chips */ + H16_34XX_SDRC_CKE0, + H17_34XX_SDRC_CKE1, }; struct omap_mux_cfg { -- cgit v1.2.3-70-g09d2 From 75f251e3d0803b028f3474fdc75be0994c377ab5 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 24 Jul 2009 19:44:01 -0600 Subject: OMAP2/3 SDRC: don't set SDRC_POWER.PWDENA on boot Stop setting SDRC_POWER.PWDENA on boot. There is a nasty erratum (34xx erratum 1.150) that can cause memory corruption if PWDENA is enabled. Based originally on a patch from Samu P. Onkalo . Tested on BeagleBoard rev C2. Signed-off-by: Paul Walmsley Cc: Samu P. Onkalo --- arch/arm/mach-omap2/sdrc.c | 5 ++++- arch/arm/mach-omap2/sram34xx.S | 2 -- 2 files changed, 4 insertions(+), 3 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/sdrc.c b/arch/arm/mach-omap2/sdrc.c index 2e9e38db30e..9e3bd4fa781 100644 --- a/arch/arm/mach-omap2/sdrc.c +++ b/arch/arm/mach-omap2/sdrc.c @@ -125,8 +125,11 @@ void __init omap2_sdrc_init(struct omap_sdrc_params *sdrc_cs0, sdrc_init_params_cs1 = sdrc_cs1; /* XXX Enable SRFRONIDLEREQ here also? */ + /* + * PWDENA should not be set due to 34xx erratum 1.150 - PWDENA + * can cause random memory corruption + */ l = (1 << SDRC_POWER_EXTCLKDIS_SHIFT) | - (1 << SDRC_POWER_PWDENA_SHIFT) | (1 << SDRC_POWER_PAGEPOLICY_SHIFT); sdrc_write_reg(l, SDRC_POWER); } diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index 3aef7448b2a..9c2d0465a83 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -58,7 +58,6 @@ /* SDRC_POWER bit settings */ #define SRFRONIDLEREQ_MASK 0x40 -#define PWDENA_MASK 0x4 /* CM_IDLEST1_CORE bit settings */ #define ST_SDRC_MASK 0x2 @@ -160,7 +159,6 @@ sdram_in_selfrefresh: ldr r12, [r11] @ read the contents of SDRC_POWER mov r9, r12 @ keep a copy of SDRC_POWER bits orr r12, r12, #SRFRONIDLEREQ_MASK @ enable self refresh on idle - bic r12, r12, #PWDENA_MASK @ clear PWDENA str r12, [r11] @ write back to SDRC_POWER register ldr r12, [r11] @ posted-write barrier for SDRC idle_sdrc: -- cgit v1.2.3-70-g09d2 From 8ff120e5303e27e03aba7b774e86fd43eaf90376 Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Fri, 24 Jul 2009 19:44:01 -0600 Subject: OMAP3 SDRC: Fix freeze when scaling CORE dpll to < 83Mhz This patch fixes a bug in the CORE dpll scaling sequence which was errouneously clearing some bits in the SDRC DLLA CTRL register and hence causing a freeze. The issue was observed only on platforms which scale CORE dpll to < 83Mhz and hence program the DLL in fixed delay mode. Issue reported by Limei Wang , with debugging assistance from Richard Woodruff and Girish Ghongdemath . Signed-off-by: Rajendra Nayak Cc: Limei Wang Cc: Richard Woodruff Cc: Girish Ghongdemath Signed-off-by: Paul Walmsley [paul@pwsan.com: updated patch description to include collaboration credits] --- arch/arm/mach-omap2/sram34xx.S | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index 9c2d0465a83..e6b112590d7 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -143,7 +143,7 @@ return_to_sdram: unlock_dll: ldr r11, omap3_sdrc_dlla_ctrl ldr r12, [r11] - and r12, r12, #FIXEDDELAY_MASK + bic r12, r12, #FIXEDDELAY_MASK orr r12, r12, #FIXEDDELAY_DEFAULT orr r12, r12, #DLLIDLE_MASK str r12, [r11] @ (no OCP barrier needed) -- cgit v1.2.3-70-g09d2 From df56556e571234cf26072cd58c01ac3520986b44 Mon Sep 17 00:00:00 2001 From: Rajendra Nayak Date: Fri, 24 Jul 2009 19:44:02 -0600 Subject: OMAP3 SDRC: Move the clk stabilization delay to the right place The clock stabilization delay post a M2 divider change is needed even before a SDRC interface clock re-enable and not only before jumping back to SDRAM. Signed-off-by: Rajendra Nayak Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/sram34xx.S | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/sram34xx.S b/arch/arm/mach-omap2/sram34xx.S index e6b112590d7..82aa4a3d160 100644 --- a/arch/arm/mach-omap2/sram34xx.S +++ b/arch/arm/mach-omap2/sram34xx.S @@ -127,6 +127,8 @@ skip_cs1_params: blne lock_dll bl sdram_in_selfrefresh @ put SDRAM in self refresh, idle SDRC bl configure_core_dpll @ change the DPLL3 M2 divider + mov r12, r2 + bl wait_clk_stable @ wait for SDRC to stabilize bl enable_sdrc @ take SDRC out of idle cmp r1, #SDRC_UNLOCK_DLL @ wait for DLL status to change bleq wait_dll_unlock @@ -134,8 +136,6 @@ skip_cs1_params: cmp r3, #1 @ if increasing SDRC clk rate, beq return_to_sdram @ return to SDRAM code, otherwise, bl configure_sdrc @ reprogram SDRC regs now - mov r12, r2 - bl wait_clk_stable @ wait for SDRC to stabilize return_to_sdram: isb @ prevent speculative exec past here mov r0, #0 @ return value -- cgit v1.2.3-70-g09d2 From 72350b29a4c0debfc27c2edbeed9b4ff3f935dd4 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 24 Jul 2009 19:44:03 -0600 Subject: OMAP2/3 clock: split, rename omap2_wait_clock_ready() Some OMAP2/3 hardware modules have CM_IDLEST attributes that are not handled by the current omap2_wait_clock_ready() code. In preparation for patches that fix the unusual devices, rename the function omap2_wait_clock_ready() to omap2_wait_module_ready() and split it into three parts: 1. A clkops-specific companion clock return function (by default, omap2_clk_dflt_find_companion()) 2. A clkops-specific CM_IDLEST register address and bit shift return function (by default, omap2_clk_dflt_find_idlest()) 3. Code to wait for the CM to indicate that the module is ready (omap2_cm_wait_idlest()) Clocks can now specify their own custom find_companion() and find_idlest() functions; used in subsequent patches. Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/clock.c | 156 ++++++++++++++++---------------- arch/arm/mach-omap2/clock.h | 6 ++ arch/arm/mach-omap2/prcm.c | 43 +++++++++ arch/arm/plat-omap/include/mach/clock.h | 2 + arch/arm/plat-omap/include/mach/prcm.h | 1 + 5 files changed, 131 insertions(+), 77 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock.c b/arch/arm/mach-omap2/clock.c index b0665f161c0..456e2ad5f62 100644 --- a/arch/arm/mach-omap2/clock.c +++ b/arch/arm/mach-omap2/clock.c @@ -27,6 +27,7 @@ #include #include #include +#include #include #include @@ -38,8 +39,6 @@ #include "cm-regbits-24xx.h" #include "cm-regbits-34xx.h" -#define MAX_CLOCK_ENABLE_WAIT 100000 - /* DPLL rate rounding: minimum DPLL multiplier, divider values */ #define DPLL_MIN_MULTIPLIER 1 #define DPLL_MIN_DIVIDER 1 @@ -274,83 +273,97 @@ unsigned long omap2_fixed_divisor_recalc(struct clk *clk) } /** - * omap2_wait_clock_ready - wait for clock to enable - * @reg: physical address of clock IDLEST register - * @mask: value to mask against to determine if the clock is active - * @name: name of the clock (for printk) + * omap2_clk_dflt_find_companion - find companion clock to @clk + * @clk: struct clk * to find the companion clock of + * @other_reg: void __iomem ** to return the companion clock CM_*CLKEN va in + * @other_bit: u8 ** to return the companion clock bit shift in + * + * Note: We don't need special code here for INVERT_ENABLE for the + * time being since INVERT_ENABLE only applies to clocks enabled by + * CM_CLKEN_PLL * - * Returns 1 if the clock enabled in time, or 0 if it failed to enable - * in roughly MAX_CLOCK_ENABLE_WAIT microseconds. + * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes it's + * just a matter of XORing the bits. + * + * Some clocks don't have companion clocks. For example, modules with + * only an interface clock (such as MAILBOXES) don't have a companion + * clock. Right now, this code relies on the hardware exporting a bit + * in the correct companion register that indicates that the + * nonexistent 'companion clock' is active. Future patches will + * associate this type of code with per-module data structures to + * avoid this issue, and remove the casts. No return value. */ -int omap2_wait_clock_ready(void __iomem *reg, u32 mask, const char *name) +void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg, + u8 *other_bit) { - int i = 0; - int ena = 0; + u32 r; /* - * 24xx uses 0 to indicate not ready, and 1 to indicate ready. - * 34xx reverses this, just to keep us on our toes + * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes + * it's just a matter of XORing the bits. */ - if (cpu_mask & (RATE_IN_242X | RATE_IN_243X)) - ena = mask; - else if (cpu_mask & RATE_IN_343X) - ena = 0; - - /* Wait for lock */ - while (((__raw_readl(reg) & mask) != ena) && - (i++ < MAX_CLOCK_ENABLE_WAIT)) { - udelay(1); - } - - if (i <= MAX_CLOCK_ENABLE_WAIT) - pr_debug("Clock %s stable after %d loops\n", name, i); - else - printk(KERN_ERR "Clock %s didn't enable in %d tries\n", - name, MAX_CLOCK_ENABLE_WAIT); - - - return (i < MAX_CLOCK_ENABLE_WAIT) ? 1 : 0; -}; + r = ((__force u32)clk->enable_reg ^ (CM_FCLKEN ^ CM_ICLKEN)); + *other_reg = (__force void __iomem *)r; + *other_bit = clk->enable_bit; +} -/* - * Note: We don't need special code here for INVERT_ENABLE - * for the time being since INVERT_ENABLE only applies to clocks enabled by - * CM_CLKEN_PLL +/** + * omap2_clk_dflt_find_idlest - find CM_IDLEST reg va, bit shift for @clk + * @clk: struct clk * to find IDLEST info for + * @idlest_reg: void __iomem ** to return the CM_IDLEST va in + * @idlest_bit: u8 ** to return the CM_IDLEST bit shift in + * + * Return the CM_IDLEST register address and bit shift corresponding + * to the module that "owns" this clock. This default code assumes + * that the CM_IDLEST bit shift is the CM_*CLKEN bit shift, and that + * the IDLEST register address ID corresponds to the CM_*CLKEN + * register address ID (e.g., that CM_FCLKEN2 corresponds to + * CM_IDLEST2). This is not true for all modules. No return value. */ -static void omap2_clk_wait_ready(struct clk *clk) +void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg, + u8 *idlest_bit) { - void __iomem *reg, *other_reg, *st_reg; - u32 bit; + u32 r; - /* - * REVISIT: This code is pretty ugly. It would be nice to generalize - * it and pull it into struct clk itself somehow. - */ - reg = clk->enable_reg; + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = clk->enable_bit; +} - /* - * Convert CM_ICLKEN* <-> CM_FCLKEN*. This conversion assumes - * it's just a matter of XORing the bits. - */ - other_reg = (void __iomem *)((u32)reg ^ (CM_FCLKEN ^ CM_ICLKEN)); +/** + * omap2_module_wait_ready - wait for an OMAP module to leave IDLE + * @clk: struct clk * belonging to the module + * + * If the necessary clocks for the OMAP hardware IP block that + * corresponds to clock @clk are enabled, then wait for the module to + * indicate readiness (i.e., to leave IDLE). This code does not + * belong in the clock code and will be moved in the medium term to + * module-dependent code. No return value. + */ +static void omap2_module_wait_ready(struct clk *clk) +{ + void __iomem *companion_reg, *idlest_reg; + u8 other_bit, idlest_bit; + + /* Not all modules have multiple clocks that their IDLEST depends on */ + if (clk->ops->find_companion) { + clk->ops->find_companion(clk, &companion_reg, &other_bit); + if (!(__raw_readl(companion_reg) & (1 << other_bit))) + return; + } - /* Check if both functional and interface clocks - * are running. */ - bit = 1 << clk->enable_bit; - if (!(__raw_readl(other_reg) & bit)) - return; - st_reg = (void __iomem *)(((u32)other_reg & ~0xf0) | 0x20); /* CM_IDLEST* */ + clk->ops->find_idlest(clk, &idlest_reg, &idlest_bit); - omap2_wait_clock_ready(st_reg, bit, clk->name); + omap2_cm_wait_idlest(idlest_reg, (1 << idlest_bit), clk->name); } -static int omap2_dflt_clk_enable(struct clk *clk) +int omap2_dflt_clk_enable(struct clk *clk) { u32 v; if (unlikely(clk->enable_reg == NULL)) { - printk(KERN_ERR "clock.c: Enable for %s without enable code\n", + pr_err("clock.c: Enable for %s without enable code\n", clk->name); return 0; /* REVISIT: -EINVAL */ } @@ -363,26 +376,13 @@ static int omap2_dflt_clk_enable(struct clk *clk) __raw_writel(v, clk->enable_reg); v = __raw_readl(clk->enable_reg); /* OCP barrier */ - return 0; -} + if (clk->ops->find_idlest) + omap2_module_wait_ready(clk); -static int omap2_dflt_clk_enable_wait(struct clk *clk) -{ - int ret; - - if (!clk->enable_reg) { - printk(KERN_ERR "clock.c: Enable for %s without enable code\n", - clk->name); - return 0; /* REVISIT: -EINVAL */ - } - - ret = omap2_dflt_clk_enable(clk); - if (ret == 0) - omap2_clk_wait_ready(clk); - return ret; + return 0; } -static void omap2_dflt_clk_disable(struct clk *clk) +void omap2_dflt_clk_disable(struct clk *clk) { u32 v; @@ -406,8 +406,10 @@ static void omap2_dflt_clk_disable(struct clk *clk) } const struct clkops clkops_omap2_dflt_wait = { - .enable = omap2_dflt_clk_enable_wait, + .enable = omap2_dflt_clk_enable, .disable = omap2_dflt_clk_disable, + .find_companion = omap2_clk_dflt_find_companion, + .find_idlest = omap2_clk_dflt_find_idlest, }; const struct clkops clkops_omap2_dflt = { diff --git a/arch/arm/mach-omap2/clock.h b/arch/arm/mach-omap2/clock.h index 2679ddfa642..9ae7540f8af 100644 --- a/arch/arm/mach-omap2/clock.h +++ b/arch/arm/mach-omap2/clock.h @@ -65,6 +65,12 @@ int omap2_clksel_set_rate(struct clk *clk, unsigned long rate); u32 omap2_get_dpll_rate(struct clk *clk); int omap2_wait_clock_ready(void __iomem *reg, u32 cval, const char *name); void omap2_clk_prepare_for_reboot(void); +int omap2_dflt_clk_enable(struct clk *clk); +void omap2_dflt_clk_disable(struct clk *clk); +void omap2_clk_dflt_find_companion(struct clk *clk, void __iomem **other_reg, + u8 *other_bit); +void omap2_clk_dflt_find_idlest(struct clk *clk, void __iomem **idlest_reg, + u8 *idlest_bit); extern const struct clkops clkops_omap2_dflt_wait; extern const struct clkops clkops_omap2_dflt; diff --git a/arch/arm/mach-omap2/prcm.c b/arch/arm/mach-omap2/prcm.c index f945156d558..ced555a4cd1 100644 --- a/arch/arm/mach-omap2/prcm.c +++ b/arch/arm/mach-omap2/prcm.c @@ -17,6 +17,7 @@ #include #include #include +#include #include #include @@ -28,6 +29,8 @@ static void __iomem *prm_base; static void __iomem *cm_base; +#define MAX_MODULE_ENABLE_WAIT 100000 + u32 omap_prcm_get_reset_sources(void) { /* XXX This presumably needs modification for 34XX */ @@ -120,6 +123,46 @@ u32 cm_rmw_mod_reg_bits(u32 mask, u32 bits, s16 module, s16 idx) } EXPORT_SYMBOL(cm_rmw_mod_reg_bits); +/** + * omap2_cm_wait_idlest - wait for IDLEST bit to indicate module readiness + * @reg: physical address of module IDLEST register + * @mask: value to mask against to determine if the module is active + * @name: name of the clock (for printk) + * + * Returns 1 if the module indicated readiness in time, or 0 if it + * failed to enable in roughly MAX_MODULE_ENABLE_WAIT microseconds. + */ +int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name) +{ + int i = 0; + int ena = 0; + + /* + * 24xx uses 0 to indicate not ready, and 1 to indicate ready. + * 34xx reverses this, just to keep us on our toes + */ + if (cpu_is_omap24xx()) + ena = mask; + else if (cpu_is_omap34xx()) + ena = 0; + else + BUG(); + + /* Wait for lock */ + while (((__raw_readl(reg) & mask) != ena) && + (i++ < MAX_MODULE_ENABLE_WAIT)) + udelay(1); + + if (i < MAX_MODULE_ENABLE_WAIT) + pr_debug("cm: Module associated with clock %s ready after %d " + "loops\n", name, i); + else + pr_err("cm: Module associated with clock %s didn't enable in " + "%d tries\n", name, MAX_MODULE_ENABLE_WAIT); + + return (i < MAX_MODULE_ENABLE_WAIT) ? 1 : 0; +}; + void __init omap2_set_globals_prcm(struct omap_globals *omap2_globals) { prm_base = omap2_globals->prm; diff --git a/arch/arm/plat-omap/include/mach/clock.h b/arch/arm/plat-omap/include/mach/clock.h index f9f65e1ba3f..4b8b0d65cbf 100644 --- a/arch/arm/plat-omap/include/mach/clock.h +++ b/arch/arm/plat-omap/include/mach/clock.h @@ -20,6 +20,8 @@ struct clockdomain; struct clkops { int (*enable)(struct clk *); void (*disable)(struct clk *); + void (*find_idlest)(struct clk *, void __iomem **, u8 *); + void (*find_companion)(struct clk *, void __iomem **, u8 *); }; #if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3) || \ diff --git a/arch/arm/plat-omap/include/mach/prcm.h b/arch/arm/plat-omap/include/mach/prcm.h index 24ac3c71591..cda2a70397b 100644 --- a/arch/arm/plat-omap/include/mach/prcm.h +++ b/arch/arm/plat-omap/include/mach/prcm.h @@ -25,6 +25,7 @@ u32 omap_prcm_get_reset_sources(void); void omap_prcm_arch_reset(char mode); +int omap2_cm_wait_idlest(void __iomem *reg, u32 mask, const char *name); #endif -- cgit v1.2.3-70-g09d2 From 3dc2197579089c5b74c7fba666c8ccf1a449afb4 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 24 Jul 2009 19:44:04 -0600 Subject: OMAP2 clock: 2430 I2CHS uses non-standard CM_IDLEST register OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE [1]. Fix by implementing a custom clkops .find_idlest function to return the correct slave IDLEST register. ... 1. OMAP2430 Multimedia Device Package-on-Package (POP) Silicon Revision 2.1 (Rev. V) Technical Reference Manual, tables 4-99 and 4-105. Signed-off-by: Paul Walmsley --- arch/arm/mach-omap2/clock24xx.c | 37 +++++++++++++++++++++++++++++++++++-- arch/arm/mach-omap2/clock24xx.h | 4 ++-- 2 files changed, 37 insertions(+), 4 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock24xx.c b/arch/arm/mach-omap2/clock24xx.c index 44de0271fc2..bc5d3ac6661 100644 --- a/arch/arm/mach-omap2/clock24xx.c +++ b/arch/arm/mach-omap2/clock24xx.c @@ -30,6 +30,7 @@ #include #include +#include #include #include @@ -43,6 +44,18 @@ static const struct clkops clkops_oscck; static const struct clkops clkops_fixed; +static void omap2430_clk_i2chs_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit); + +/* 2430 I2CHS has non-standard IDLEST register */ +static const struct clkops clkops_omap2430_i2chs_wait = { + .enable = omap2_dflt_clk_enable, + .disable = omap2_dflt_clk_disable, + .find_idlest = omap2430_clk_i2chs_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + #include "clock24xx.h" struct omap_clk { @@ -239,6 +252,26 @@ static void __iomem *prcm_clksrc_ctrl; * Omap24xx specific clock functions *-------------------------------------------------------------------------*/ +/** + * omap2430_clk_i2chs_find_idlest - return CM_IDLEST info for 2430 I2CHS + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * + * OMAP2430 I2CHS CM_IDLEST bits are in CM_IDLEST1_CORE, but the + * CM_*CLKEN bits are in CM_{I,F}CLKEN2_CORE. This custom function + * passes back the correct CM_IDLEST register address for I2CHS + * modules. No return value. + */ +static void omap2430_clk_i2chs_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit) +{ + *idlest_reg = OMAP_CM_REGADDR(CORE_MOD, CM_IDLEST); + *idlest_bit = clk->enable_bit; +} + + /** * omap2xxx_clk_get_core_rate - return the CORE_CLK rate * @clk: pointer to the combined dpll_ck + core_ck (currently "dpll_ck") @@ -325,8 +358,8 @@ static int omap2_clk_fixed_enable(struct clk *clk) else if (clk == &apll54_ck) cval = OMAP24XX_ST_54M_APLL; - omap2_wait_clock_ready(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval, - clk->name); + omap2_cm_wait_idlest(OMAP_CM_REGADDR(PLL_MOD, CM_IDLEST), cval, + clk->name); /* * REVISIT: Should we return an error code if omap2_wait_clock_ready() diff --git a/arch/arm/mach-omap2/clock24xx.h b/arch/arm/mach-omap2/clock24xx.h index 458f00cdcbe..d19cf7a7d8d 100644 --- a/arch/arm/mach-omap2/clock24xx.h +++ b/arch/arm/mach-omap2/clock24xx.h @@ -2337,7 +2337,7 @@ static struct clk i2c2_fck = { static struct clk i2chs2_fck = { .name = "i2c_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2430_i2chs_wait, .id = 2, .parent = &func_96m_ck, .clkdm_name = "core_l4_clkdm", @@ -2370,7 +2370,7 @@ static struct clk i2c1_fck = { static struct clk i2chs1_fck = { .name = "i2c_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2430_i2chs_wait, .id = 1, .parent = &func_96m_ck, .clkdm_name = "core_l4_clkdm", -- cgit v1.2.3-70-g09d2 From 3c82e229f09a6acc8d24dc27c5e0e60b1d7161c2 Mon Sep 17 00:00:00 2001 From: Paul Walmsley Date: Fri, 24 Jul 2009 19:44:06 -0600 Subject: OMAP3 clock: correct module IDLEST bits: SSI; DSS; USBHOST; HSOTGUSB Fix two bugs in the OMAP3 clock tree pertaining to the SSI, DSS, USBHOST, and HSOTGUSB devices. These devices are both interconnect initiators and targets. Without this patch, clk_enable()s on clocks for these modules can be very high latency (potentially up to ~200 milliseconds) and message such as the following are generated: Clock usbhost_48m_fck didn't enable in 100000 tries Two bugs are fixed by this patch. First, OMAP hardware only supports target CM_IDLEST register bits on ES2+ chips and beyond. ES1 chips should not wait for these clocks to enable. So, split the appropriate clocks into ES1 and ES2+ variants, so that kernels running on ES1 devices won't try to wait. Second, the current heuristic in omap2_clk_dflt_find_idlest() will fail for these clocks. It assumes that the CM_IDLEST bit to wait upon is the same as the CM_*CLKEN bit, which is false[1]. Fix by implementing custom clkops .find_idlest function pointers for the appropriate clocks that return the correct slave IDLEST bit shift. This was originally fixed in the linux-omap kernel during 2.6.29 in a slightly different manner[2][3]. In the medium-term future, all of the module IDLEST code will eventually be moved to the omap_hwmod code. Problem reported by Jarkko Nikula : http://marc.info/?l=linux-omap&m=124306184903679&w=2 ... 1. See for example 34xx TRM Revision P Table 4-213 and 4-217 (for the DSS case). 2. http://www.spinics.net/lists/linux-omap/msg05512.html et seq. 3. http://lkml.indiana.edu/hypermail/linux/kernel/0901.3/01498.html Signed-off-by: Paul Walmsley Cc: Jarkko Nikula --- arch/arm/mach-omap2/clock34xx.c | 118 +++++++++++++++++++++++++++++++++++++--- arch/arm/mach-omap2/clock34xx.h | 85 +++++++++++++++++++++++++---- 2 files changed, 185 insertions(+), 18 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/clock34xx.c b/arch/arm/mach-omap2/clock34xx.c index 1c6480d3ad6..cd7819cc0c9 100644 --- a/arch/arm/mach-omap2/clock34xx.c +++ b/arch/arm/mach-omap2/clock34xx.c @@ -2,7 +2,7 @@ * OMAP3-specific clock framework functions * * Copyright (C) 2007-2008 Texas Instruments, Inc. - * Copyright (C) 2007-2008 Nokia Corporation + * Copyright (C) 2007-2009 Nokia Corporation * * Written by Paul Walmsley * Testing and integration fixes by Jouni Högander @@ -41,6 +41,37 @@ static const struct clkops clkops_noncore_dpll_ops; +static void omap3430es2_clk_ssi_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit); +static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit); +static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit); + +static const struct clkops clkops_omap3430es2_ssi_wait = { + .enable = omap2_dflt_clk_enable, + .disable = omap2_dflt_clk_disable, + .find_idlest = omap3430es2_clk_ssi_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + +static const struct clkops clkops_omap3430es2_hsotgusb_wait = { + .enable = omap2_dflt_clk_enable, + .disable = omap2_dflt_clk_disable, + .find_idlest = omap3430es2_clk_hsotgusb_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + +static const struct clkops clkops_omap3430es2_dss_usbhost_wait = { + .enable = omap2_dflt_clk_enable, + .disable = omap2_dflt_clk_disable, + .find_idlest = omap3430es2_clk_dss_usbhost_find_idlest, + .find_companion = omap2_clk_dflt_find_companion, +}; + #include "clock34xx.h" struct omap_clk { @@ -157,10 +188,13 @@ static struct omap_clk omap34xx_clks[] = { CLK(NULL, "fshostusb_fck", &fshostusb_fck, CK_3430ES1), CLK(NULL, "core_12m_fck", &core_12m_fck, CK_343X), CLK("omap_hdq.0", "fck", &hdq_fck, CK_343X), - CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck, CK_343X), - CLK(NULL, "ssi_sst_fck", &ssi_sst_fck, CK_343X), + CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck_3430es1, CK_3430ES1), + CLK(NULL, "ssi_ssr_fck", &ssi_ssr_fck_3430es2, CK_3430ES2), + CLK(NULL, "ssi_sst_fck", &ssi_sst_fck_3430es1, CK_3430ES1), + CLK(NULL, "ssi_sst_fck", &ssi_sst_fck_3430es2, CK_3430ES2), CLK(NULL, "core_l3_ick", &core_l3_ick, CK_343X), - CLK("musb_hdrc", "ick", &hsotgusb_ick, CK_343X), + CLK("musb_hdrc", "ick", &hsotgusb_ick_3430es1, CK_3430ES1), + CLK("musb_hdrc", "ick", &hsotgusb_ick_3430es2, CK_3430ES2), CLK(NULL, "sdrc_ick", &sdrc_ick, CK_343X), CLK(NULL, "gpmc_fck", &gpmc_fck, CK_343X), CLK(NULL, "security_l3_ick", &security_l3_ick, CK_343X), @@ -193,18 +227,21 @@ static struct omap_clk omap34xx_clks[] = { CLK(NULL, "mailboxes_ick", &mailboxes_ick, CK_343X), CLK(NULL, "omapctrl_ick", &omapctrl_ick, CK_343X), CLK(NULL, "ssi_l4_ick", &ssi_l4_ick, CK_343X), - CLK(NULL, "ssi_ick", &ssi_ick, CK_343X), + CLK(NULL, "ssi_ick", &ssi_ick_3430es1, CK_3430ES1), + CLK(NULL, "ssi_ick", &ssi_ick_3430es2, CK_3430ES2), CLK(NULL, "usb_l4_ick", &usb_l4_ick, CK_3430ES1), CLK(NULL, "security_l4_ick2", &security_l4_ick2, CK_343X), CLK(NULL, "aes1_ick", &aes1_ick, CK_343X), CLK("omap_rng", "ick", &rng_ick, CK_343X), CLK(NULL, "sha11_ick", &sha11_ick, CK_343X), CLK(NULL, "des1_ick", &des1_ick, CK_343X), - CLK("omapfb", "dss1_fck", &dss1_alwon_fck, CK_343X), + CLK("omapfb", "dss1_fck", &dss1_alwon_fck_3430es1, CK_3430ES1), + CLK("omapfb", "dss1_fck", &dss1_alwon_fck_3430es2, CK_3430ES2), CLK("omapfb", "tv_fck", &dss_tv_fck, CK_343X), CLK("omapfb", "video_fck", &dss_96m_fck, CK_343X), CLK("omapfb", "dss2_fck", &dss2_alwon_fck, CK_343X), - CLK("omapfb", "ick", &dss_ick, CK_343X), + CLK("omapfb", "ick", &dss_ick_3430es1, CK_3430ES1), + CLK("omapfb", "ick", &dss_ick_3430es2, CK_3430ES2), CLK(NULL, "cam_mclk", &cam_mclk, CK_343X), CLK(NULL, "cam_ick", &cam_ick, CK_343X), CLK(NULL, "csi2_96m_fck", &csi2_96m_fck, CK_343X), @@ -300,6 +337,73 @@ static struct omap_clk omap34xx_clks[] = { */ #define SDRC_MPURATE_LOOPS 96 +/** + * omap3430es2_clk_ssi_find_idlest - return CM_IDLEST info for SSI + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * + * The OMAP3430ES2 SSI target CM_IDLEST bit is at a different shift + * from the CM_{I,F}CLKEN bit. Pass back the correct info via + * @idlest_reg and @idlest_bit. No return value. + */ +static void omap3430es2_clk_ssi_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = OMAP3430ES2_ST_SSI_IDLE_SHIFT; +} + +/** + * omap3430es2_clk_dss_usbhost_find_idlest - CM_IDLEST info for DSS, USBHOST + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * + * Some OMAP modules on OMAP3 ES2+ chips have both initiator and + * target IDLEST bits. For our purposes, we are concerned with the + * target IDLEST bits, which exist at a different bit position than + * the *CLKEN bit position for these modules (DSS and USBHOST) (The + * default find_idlest code assumes that they are at the same + * position.) No return value. + */ +static void omap3430es2_clk_dss_usbhost_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + /* USBHOST_IDLE has same shift */ + *idlest_bit = OMAP3430ES2_ST_DSS_IDLE_SHIFT; +} + +/** + * omap3430es2_clk_hsotgusb_find_idlest - return CM_IDLEST info for HSOTGUSB + * @clk: struct clk * being enabled + * @idlest_reg: void __iomem ** to store CM_IDLEST reg address into + * @idlest_bit: pointer to a u8 to store the CM_IDLEST bit shift into + * + * The OMAP3430ES2 HSOTGUSB target CM_IDLEST bit is at a different + * shift from the CM_{I,F}CLKEN bit. Pass back the correct info via + * @idlest_reg and @idlest_bit. No return value. + */ +static void omap3430es2_clk_hsotgusb_find_idlest(struct clk *clk, + void __iomem **idlest_reg, + u8 *idlest_bit) +{ + u32 r; + + r = (((__force u32)clk->enable_reg & ~0xf0) | 0x20); + *idlest_reg = (__force void __iomem *)r; + *idlest_bit = OMAP3430ES2_ST_HSOTGUSB_IDLE_SHIFT; +} + /** * omap3_dpll_recalc - recalculate DPLL rate * @clk: DPLL struct clk diff --git a/arch/arm/mach-omap2/clock34xx.h b/arch/arm/mach-omap2/clock34xx.h index e433aec4efd..57cc2725b92 100644 --- a/arch/arm/mach-omap2/clock34xx.h +++ b/arch/arm/mach-omap2/clock34xx.h @@ -1568,7 +1568,7 @@ static const struct clksel ssi_ssr_clksel[] = { { .parent = NULL } }; -static struct clk ssi_ssr_fck = { +static struct clk ssi_ssr_fck_3430es1 = { .name = "ssi_ssr_fck", .ops = &clkops_omap2_dflt, .init = &omap2_init_clksel_parent, @@ -1581,10 +1581,31 @@ static struct clk ssi_ssr_fck = { .recalc = &omap2_clksel_recalc, }; -static struct clk ssi_sst_fck = { +static struct clk ssi_ssr_fck_3430es2 = { + .name = "ssi_ssr_fck", + .ops = &clkops_omap3430es2_ssi_wait, + .init = &omap2_init_clksel_parent, + .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_FCLKEN1), + .enable_bit = OMAP3430_EN_SSI_SHIFT, + .clksel_reg = OMAP_CM_REGADDR(CORE_MOD, CM_CLKSEL), + .clksel_mask = OMAP3430_CLKSEL_SSI_MASK, + .clksel = ssi_ssr_clksel, + .clkdm_name = "core_l4_clkdm", + .recalc = &omap2_clksel_recalc, +}; + +static struct clk ssi_sst_fck_3430es1 = { .name = "ssi_sst_fck", .ops = &clkops_null, - .parent = &ssi_ssr_fck, + .parent = &ssi_ssr_fck_3430es1, + .fixed_div = 2, + .recalc = &omap2_fixed_divisor_recalc, +}; + +static struct clk ssi_sst_fck_3430es2 = { + .name = "ssi_sst_fck", + .ops = &clkops_null, + .parent = &ssi_ssr_fck_3430es2, .fixed_div = 2, .recalc = &omap2_fixed_divisor_recalc, }; @@ -1606,9 +1627,19 @@ static struct clk core_l3_ick = { .recalc = &followparent_recalc, }; -static struct clk hsotgusb_ick = { +static struct clk hsotgusb_ick_3430es1 = { .name = "hsotgusb_ick", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2_dflt, + .parent = &core_l3_ick, + .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), + .enable_bit = OMAP3430_EN_HSOTGUSB_SHIFT, + .clkdm_name = "core_l3_clkdm", + .recalc = &followparent_recalc, +}; + +static struct clk hsotgusb_ick_3430es2 = { + .name = "hsotgusb_ick", + .ops = &clkops_omap3430es2_hsotgusb_wait, .parent = &core_l3_ick, .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), .enable_bit = OMAP3430_EN_HSOTGUSB_SHIFT, @@ -1947,7 +1978,7 @@ static struct clk ssi_l4_ick = { .recalc = &followparent_recalc, }; -static struct clk ssi_ick = { +static struct clk ssi_ick_3430es1 = { .name = "ssi_ick", .ops = &clkops_omap2_dflt, .parent = &ssi_l4_ick, @@ -1957,6 +1988,16 @@ static struct clk ssi_ick = { .recalc = &followparent_recalc, }; +static struct clk ssi_ick_3430es2 = { + .name = "ssi_ick", + .ops = &clkops_omap3430es2_ssi_wait, + .parent = &ssi_l4_ick, + .enable_reg = OMAP_CM_REGADDR(CORE_MOD, CM_ICLKEN1), + .enable_bit = OMAP3430_EN_SSI_SHIFT, + .clkdm_name = "core_l4_clkdm", + .recalc = &followparent_recalc, +}; + /* REVISIT: Technically the TRM claims that this is CORE_CLK based, * but l4_ick makes more sense to me */ @@ -2024,7 +2065,7 @@ static struct clk des1_ick = { }; /* DSS */ -static struct clk dss1_alwon_fck = { +static struct clk dss1_alwon_fck_3430es1 = { .name = "dss1_alwon_fck", .ops = &clkops_omap2_dflt, .parent = &dpll4_m4x2_ck, @@ -2034,6 +2075,16 @@ static struct clk dss1_alwon_fck = { .recalc = &followparent_recalc, }; +static struct clk dss1_alwon_fck_3430es2 = { + .name = "dss1_alwon_fck", + .ops = &clkops_omap3430es2_dss_usbhost_wait, + .parent = &dpll4_m4x2_ck, + .enable_reg = OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_FCLKEN), + .enable_bit = OMAP3430_EN_DSS1_SHIFT, + .clkdm_name = "dss_clkdm", + .recalc = &followparent_recalc, +}; + static struct clk dss_tv_fck = { .name = "dss_tv_fck", .ops = &clkops_omap2_dflt, @@ -2067,7 +2118,7 @@ static struct clk dss2_alwon_fck = { .recalc = &followparent_recalc, }; -static struct clk dss_ick = { +static struct clk dss_ick_3430es1 = { /* Handles both L3 and L4 clocks */ .name = "dss_ick", .ops = &clkops_omap2_dflt, @@ -2079,6 +2130,18 @@ static struct clk dss_ick = { .recalc = &followparent_recalc, }; +static struct clk dss_ick_3430es2 = { + /* Handles both L3 and L4 clocks */ + .name = "dss_ick", + .ops = &clkops_omap3430es2_dss_usbhost_wait, + .parent = &l4_ick, + .init = &omap2_init_clk_clkdm, + .enable_reg = OMAP_CM_REGADDR(OMAP3430_DSS_MOD, CM_ICLKEN), + .enable_bit = OMAP3430_CM_ICLKEN_DSS_EN_DSS_SHIFT, + .clkdm_name = "dss_clkdm", + .recalc = &followparent_recalc, +}; + /* CAM */ static struct clk cam_mclk = { @@ -2118,7 +2181,7 @@ static struct clk csi2_96m_fck = { static struct clk usbhost_120m_fck = { .name = "usbhost_120m_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap2_dflt, .parent = &dpll5_m2_ck, .init = &omap2_init_clk_clkdm, .enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN), @@ -2129,7 +2192,7 @@ static struct clk usbhost_120m_fck = { static struct clk usbhost_48m_fck = { .name = "usbhost_48m_fck", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap3430es2_dss_usbhost_wait, .parent = &omap_48m_fck, .init = &omap2_init_clk_clkdm, .enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_FCLKEN), @@ -2141,7 +2204,7 @@ static struct clk usbhost_48m_fck = { static struct clk usbhost_ick = { /* Handles both L3 and L4 clocks */ .name = "usbhost_ick", - .ops = &clkops_omap2_dflt_wait, + .ops = &clkops_omap3430es2_dss_usbhost_wait, .parent = &l4_ick, .init = &omap2_init_clk_clkdm, .enable_reg = OMAP_CM_REGADDR(OMAP3430ES2_USBHOST_MOD, CM_ICLKEN), -- cgit v1.2.3-70-g09d2 From efda2b4c8a643290867d9f5816e36f71a5acee7d Mon Sep 17 00:00:00 2001 From: Jaswinder Singh Rajput Date: Wed, 8 Jul 2009 20:11:05 +0530 Subject: ARM: includecheck fix: mach-omap2/mcbsp.c fix the following 'make includecheck' warning: arch/arm/mach-omap2/mcbsp.c: mach/irqs.h is included more than once. Signed-off-by: Jaswinder Singh Rajput Acked-by: Eduardo Valentin Acked-by: Kevin Hilman Signed-off-by: Russell King --- arch/arm/mach-omap2/mcbsp.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/mcbsp.c b/arch/arm/mach-omap2/mcbsp.c index a5c0f0435cd..99b6e154631 100644 --- a/arch/arm/mach-omap2/mcbsp.c +++ b/arch/arm/mach-omap2/mcbsp.c @@ -19,7 +19,6 @@ #include #include -#include #include #include #include -- cgit v1.2.3-70-g09d2 From 7cc515f74d2871daff106a17714bfd16bcb045ca Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Wed, 10 Jun 2009 09:02:25 -0700 Subject: OMAP2/3: PM: make PM __init calls static Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm.h | 3 --- arch/arm/mach-omap2/pm24xx.c | 2 +- arch/arm/mach-omap2/pm34xx.c | 2 +- 3 files changed, 2 insertions(+), 5 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/pm.h b/arch/arm/mach-omap2/pm.h index f7b3baf7667..21201cd4117 100644 --- a/arch/arm/mach-omap2/pm.h +++ b/arch/arm/mach-omap2/pm.h @@ -11,9 +11,6 @@ #ifndef __ARCH_ARM_MACH_OMAP2_PM_H #define __ARCH_ARM_MACH_OMAP2_PM_H -extern int omap2_pm_init(void); -extern int omap3_pm_init(void); - #ifdef CONFIG_PM_DEBUG extern void omap2_pm_dump(int mode, int resume, unsigned int us); extern int omap2_pm_debug; diff --git a/arch/arm/mach-omap2/pm24xx.c b/arch/arm/mach-omap2/pm24xx.c index db1025562fb..528dbdc26e2 100644 --- a/arch/arm/mach-omap2/pm24xx.c +++ b/arch/arm/mach-omap2/pm24xx.c @@ -470,7 +470,7 @@ static void __init prcm_setup_regs(void) WKUP_MOD, PM_WKEN); } -int __init omap2_pm_init(void) +static int __init omap2_pm_init(void) { u32 l; diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 841d4c5ed8b..765cdc0cd7a 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -652,7 +652,7 @@ static int __init clkdms_setup(struct clockdomain *clkdm) return 0; } -int __init omap3_pm_init(void) +static int __init omap3_pm_init(void) { struct power_state *pwrst, *tmp; int ret; -- cgit v1.2.3-70-g09d2 From 364dd47466ff7a7749bf037df4bf3b7aedbfe6f4 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 9 Jun 2009 11:45:30 -0700 Subject: OMAP3: PM: CM_REGADDR macros using wrong name Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/cm.h | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/cm.h b/arch/arm/mach-omap2/cm.h index 1d3c93bf86d..f3c91a1ca39 100644 --- a/arch/arm/mach-omap2/cm.h +++ b/arch/arm/mach-omap2/cm.h @@ -29,9 +29,9 @@ * These registers appear once per CM module. */ -#define OMAP3430_CM_REVISION OMAP_CM_REGADDR(OCP_MOD, 0x0000) -#define OMAP3430_CM_SYSCONFIG OMAP_CM_REGADDR(OCP_MOD, 0x0010) -#define OMAP3430_CM_POLCTRL OMAP_CM_REGADDR(OCP_MOD, 0x009c) +#define OMAP3430_CM_REVISION OMAP34XX_CM_REGADDR(OCP_MOD, 0x0000) +#define OMAP3430_CM_SYSCONFIG OMAP34XX_CM_REGADDR(OCP_MOD, 0x0010) +#define OMAP3430_CM_POLCTRL OMAP34XX_CM_REGADDR(OCP_MOD, 0x009c) #define OMAP3_CM_CLKOUT_CTRL_OFFSET 0x0070 #define OMAP3430_CM_CLKOUT_CTRL OMAP_CM_REGADDR(OMAP3430_CCR_MOD, 0x0070) -- cgit v1.2.3-70-g09d2 From 3a6667acf916b3e32be4682196882fc2ed0ec23e Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 27 Apr 2009 07:50:23 -0700 Subject: OMAP3: PM: Ensure PRCM interrupts are cleared at boot Any pending PRCM interrupts can prevent retention. Ensure they are cleared during boot. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 765cdc0cd7a..cc83dfc39a8 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -613,6 +613,9 @@ static void __init prcm_setup_regs(void) /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); + /* Clear any pending PRCM interrupts */ + prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); + omap3_iva_idle(); omap3_d2d_idle(); } -- cgit v1.2.3-70-g09d2 From 3a07ae30a0bfa93ff2b242acf670c6d8e2de35de Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 27 Apr 2009 16:14:54 -0700 Subject: OMAP3: PM: Clear pending PRCM reset flags on init Any pending reset flags can prevent retention. Ensure they are all cleared during boot. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 9 +++++++++ 1 file changed, 9 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index cc83dfc39a8..1422e931f57 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -613,6 +613,15 @@ static void __init prcm_setup_regs(void) /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); + /* Clear any pending 'reset' flags */ + prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430_PER_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430_EMU_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430_NEON_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430_DSS_MOD, RM_RSTST); + prm_write_mod_reg(0xffffffff, OMAP3430ES2_USBHOST_MOD, RM_RSTST); + /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); -- cgit v1.2.3-70-g09d2 From 040fed059c34da5115790609f1a038fc9aec88d1 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 5 May 2009 16:34:25 -0700 Subject: OMAP3: PM: prevent module wakeups from waking IVA2 By default, prevent functional wakeups from inside a module from waking up the IVA2. Let DSP Bridge code handle this when loaded. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 1422e931f57..c813a081c3c 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -613,6 +613,12 @@ static void __init prcm_setup_regs(void) /* Clear any pending PRCM interrupts */ prm_write_mod_reg(0, OCP_MOD, OMAP3_PRM_IRQSTATUS_MPU_OFFSET); + /* Don't attach IVA interrupts */ + prm_write_mod_reg(0, WKUP_MOD, OMAP3430_PM_IVAGRPSEL); + prm_write_mod_reg(0, CORE_MOD, OMAP3430_PM_IVAGRPSEL1); + prm_write_mod_reg(0, CORE_MOD, OMAP3430ES2_PM_IVAGRPSEL3); + prm_write_mod_reg(0, OMAP3430_PER_MOD, OMAP3430_PM_IVAGRPSEL); + /* Clear any pending 'reset' flags */ prm_write_mod_reg(0xffffffff, MPU_MOD, RM_RSTST); prm_write_mod_reg(0xffffffff, CORE_MOD, RM_RSTST); -- cgit v1.2.3-70-g09d2 From 10f90ed2d727c0f344d910c02c9726d0481d9b00 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Wed, 24 Jun 2009 11:39:18 -0700 Subject: OMAP3: PM: Do not build suspend code if SUSPEND is not enabled Signed-off-by: Jouni Hogander Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index c813a081c3c..528f725722a 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -39,7 +39,9 @@ struct power_state { struct powerdomain *pwrdm; u32 next_state; +#ifdef CONFIG_SUSPEND u32 saved_state; +#endif struct list_head node; }; @@ -293,6 +295,7 @@ out: local_irq_enable(); } +#ifdef CONFIG_SUSPEND static int omap3_pm_prepare(void) { disable_hlt(); @@ -366,6 +369,7 @@ static struct platform_suspend_ops omap_pm_ops = { .finish = omap3_pm_finish, .valid = suspend_valid_only_mem, }; +#endif /* CONFIG_SUSPEND */ /** @@ -710,7 +714,9 @@ static int __init omap3_pm_init(void) _omap_sram_idle = omap_sram_push(omap34xx_cpu_suspend, omap34xx_cpu_suspend_sz); +#ifdef CONFIG_SUSPEND suspend_set_ops(&omap_pm_ops); +#endif /* CONFIG_SUSPEND */ pm_idle = omap3_pm_idle; -- cgit v1.2.3-70-g09d2 From 4789998a30d845d94a7595076d1392ffd5a9d39e Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Wed, 24 Jun 2009 10:32:03 -0700 Subject: OMAP4: UART: cleanup special case IRQ handling Streamline the OMAP4 special IRQ assignments by putting inside normal init loop instead of having a separate loop. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/serial.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index b094c15bfe4..c82ec95cd79 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -496,10 +496,6 @@ void __init omap_serial_init(void) if (info == NULL) return; - if (cpu_is_omap44xx()) { - for (i = 0; i < OMAP_MAX_NR_PORTS; i++) - serial_platform_data[i].irq += 32; - } for (i = 0; i < OMAP_MAX_NR_PORTS; i++) { struct plat_serial8250_port *p = serial_platform_data + i; @@ -533,6 +529,9 @@ void __init omap_serial_init(void) uart->p = p; list_add(&uart->node, &uart_list); + if (cpu_is_omap44xx()) + p->irq += 32; + omap_uart_enable_clocks(uart); omap_uart_reset(uart); omap_uart_idle_init(uart); -- cgit v1.2.3-70-g09d2 From 2466211e5debd205fc550d871fe0ab9b9a6d02ed Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Thu, 5 Mar 2009 16:32:23 +0200 Subject: OMAP3: Fixed crash bug with serial + suspend It was possible for an unhandled interrupt to occur if there was incoming serial traffic during wakeup from suspend. This was caused by the code in arch-arm/mach-omap2/serial.c keeping interrupt enabled all the time, but not acking its interrupts. Applies on top of PM branch. Use the PM begin/end hooks to ensure that the "serial idle" interrupts are disabled during the suspend path. Also, since begin/end hooks are now used, use the suspend_state that is passed in the begin hook instead of the enter hook as per the platform_suspend_ops docs. Signed-off-by: Tero Kristo Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 23 +++++++++++++++++++++-- arch/arm/mach-omap2/serial.c | 14 ++++++++++++++ arch/arm/plat-omap/include/mach/serial.h | 1 + 3 files changed, 36 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index 528f725722a..b07efb26de1 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -296,6 +296,8 @@ out: } #ifdef CONFIG_SUSPEND +static suspend_state_t suspend_state; + static int omap3_pm_prepare(void) { disable_hlt(); @@ -342,11 +344,11 @@ restore: return ret; } -static int omap3_pm_enter(suspend_state_t state) +static int omap3_pm_enter(suspend_state_t unused) { int ret = 0; - switch (state) { + switch (suspend_state) { case PM_SUSPEND_STANDBY: case PM_SUSPEND_MEM: ret = omap3_pm_suspend(); @@ -363,7 +365,24 @@ static void omap3_pm_finish(void) enable_hlt(); } +/* Hooks to enable / disable UART interrupts during suspend */ +static int omap3_pm_begin(suspend_state_t state) +{ + suspend_state = state; + omap_uart_enable_irqs(0); + return 0; +} + +static void omap3_pm_end(void) +{ + suspend_state = PM_SUSPEND_ON; + omap_uart_enable_irqs(1); + return; +} + static struct platform_suspend_ops omap_pm_ops = { + .begin = omap3_pm_begin, + .end = omap3_pm_end, .prepare = omap3_pm_prepare, .enter = omap3_pm_enter, .finish = omap3_pm_finish, diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index c82ec95cd79..5352d05b42d 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -435,6 +435,20 @@ static void omap_uart_idle_init(struct omap_uart_state *uart) WARN_ON(ret); } +void omap_uart_enable_irqs(int enable) +{ + int ret; + struct omap_uart_state *uart; + + list_for_each_entry(uart, &uart_list, node) { + if (enable) + ret = request_irq(uart->p->irq, omap_uart_interrupt, + IRQF_SHARED, "serial idle", (void *)uart); + else + free_irq(uart->p->irq, (void *)uart); + } +} + static ssize_t sleep_timeout_show(struct kobject *kobj, struct kobj_attribute *attr, char *buf) diff --git a/arch/arm/plat-omap/include/mach/serial.h b/arch/arm/plat-omap/include/mach/serial.h index 13abd02d152..def0529c75e 100644 --- a/arch/arm/plat-omap/include/mach/serial.h +++ b/arch/arm/plat-omap/include/mach/serial.h @@ -59,6 +59,7 @@ extern void omap_uart_check_wakeup(void); extern void omap_uart_prepare_suspend(void); extern void omap_uart_prepare_idle(int num); extern void omap_uart_resume_idle(int num); +extern void omap_uart_enable_irqs(int enable); #endif #endif -- cgit v1.2.3-70-g09d2 From fd455ea899b5a14a8cdd276e15f3b47696526f92 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 27 Apr 2009 12:27:36 -0700 Subject: OMAP2/3/4: UART: Allow per-UART disabling wakeup for serial ports This patch causes the OMAP uarts to honor the sysfs power/wakeup file for IOPAD wakeups. Before the OMAP was always woken up from off mode on a rs232 signal change. This patch also creates a different platform device for each serial port so that the wakeup properties can be control per port. By default, IOPAD wakeups are enabled for each UART. To disable, # echo disabled > /sys/devices/platform/serial8250.0/power/wakeup Where serial8250.0 can be replaced by .1, or .2 to control the other ports. Original idea and original patch from Russ Dill Cc: Russ Dill Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/serial.c | 174 ++++++++++++++++++++++++++++--------------- 1 file changed, 116 insertions(+), 58 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 5352d05b42d..6f35a7e4893 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -54,6 +54,7 @@ struct omap_uart_state { struct plat_serial8250_port *p; struct list_head node; + struct platform_device pdev; #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM) int context_valid; @@ -68,10 +69,9 @@ struct omap_uart_state { #endif }; -static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS]; static LIST_HEAD(uart_list); -static struct plat_serial8250_port serial_platform_data[] = { +static struct plat_serial8250_port serial_platform_data0[] = { { .membase = IO_ADDRESS(OMAP_UART1_BASE), .mapbase = OMAP_UART1_BASE, @@ -81,6 +81,12 @@ static struct plat_serial8250_port serial_platform_data[] = { .regshift = 2, .uartclk = OMAP24XX_BASE_BAUD * 16, }, { + .flags = 0 + } +}; + +static struct plat_serial8250_port serial_platform_data1[] = { + { .membase = IO_ADDRESS(OMAP_UART2_BASE), .mapbase = OMAP_UART2_BASE, .irq = 73, @@ -89,6 +95,12 @@ static struct plat_serial8250_port serial_platform_data[] = { .regshift = 2, .uartclk = OMAP24XX_BASE_BAUD * 16, }, { + .flags = 0 + } +}; + +static struct plat_serial8250_port serial_platform_data2[] = { + { .membase = IO_ADDRESS(OMAP_UART3_BASE), .mapbase = OMAP_UART3_BASE, .irq = 74, @@ -217,6 +229,40 @@ static inline void omap_uart_disable_clocks(struct omap_uart_state *uart) clk_disable(uart->fck); } +static void omap_uart_enable_wakeup(struct omap_uart_state *uart) +{ + /* Set wake-enable bit */ + if (uart->wk_en && uart->wk_mask) { + u32 v = __raw_readl(uart->wk_en); + v |= uart->wk_mask; + __raw_writel(v, uart->wk_en); + } + + /* Ensure IOPAD wake-enables are set */ + if (cpu_is_omap34xx() && uart->padconf) { + u16 v = omap_ctrl_readw(uart->padconf); + v |= OMAP3_PADCONF_WAKEUPENABLE0; + omap_ctrl_writew(v, uart->padconf); + } +} + +static void omap_uart_disable_wakeup(struct omap_uart_state *uart) +{ + /* Clear wake-enable bit */ + if (uart->wk_en && uart->wk_mask) { + u32 v = __raw_readl(uart->wk_en); + v &= ~uart->wk_mask; + __raw_writel(v, uart->wk_en); + } + + /* Ensure IOPAD wake-enables are cleared */ + if (cpu_is_omap34xx() && uart->padconf) { + u16 v = omap_ctrl_readw(uart->padconf); + v &= ~OMAP3_PADCONF_WAKEUPENABLE0; + omap_ctrl_writew(v, uart->padconf); + } +} + static void omap_uart_smart_idle_enable(struct omap_uart_state *uart, int enable) { @@ -246,6 +292,11 @@ static void omap_uart_block_sleep(struct omap_uart_state *uart) static void omap_uart_allow_sleep(struct omap_uart_state *uart) { + if (device_may_wakeup(&uart->pdev.dev)) + omap_uart_enable_wakeup(uart); + else + omap_uart_disable_wakeup(uart); + if (!uart->clocked) return; @@ -292,7 +343,6 @@ void omap_uart_resume_idle(int num) /* Check for normal UART wakeup */ if (__raw_readl(uart->wk_st) & uart->wk_mask) omap_uart_block_sleep(uart); - return; } } @@ -346,16 +396,13 @@ static irqreturn_t omap_uart_interrupt(int irq, void *dev_id) return IRQ_NONE; } -static u32 sleep_timeout = DEFAULT_TIMEOUT; - static void omap_uart_idle_init(struct omap_uart_state *uart) { - u32 v; struct plat_serial8250_port *p = uart->p; int ret; uart->can_sleep = 0; - uart->timeout = sleep_timeout; + uart->timeout = DEFAULT_TIMEOUT; setup_timer(&uart->timer, omap_uart_idle_timer, (unsigned long) uart); mod_timer(&uart->timer, jiffies + uart->timeout); @@ -413,22 +460,6 @@ static void omap_uart_idle_init(struct omap_uart_state *uart) uart->padconf = 0; } - /* Set wake-enable bit */ - if (uart->wk_en && uart->wk_mask) { - v = __raw_readl(uart->wk_en); - v |= uart->wk_mask; - __raw_writel(v, uart->wk_en); - } - - /* Ensure IOPAD wake-enables are set */ - if (cpu_is_omap34xx() && uart->padconf) { - u16 v; - - v = omap_ctrl_readw(uart->padconf); - v |= OMAP3_PADCONF_WAKEUPENABLE0; - omap_ctrl_writew(v, uart->padconf); - } - p->flags |= UPF_SHARE_IRQ; ret = request_irq(p->irq, omap_uart_interrupt, IRQF_SHARED, "serial idle", (void *)uart); @@ -449,54 +480,81 @@ void omap_uart_enable_irqs(int enable) } } -static ssize_t sleep_timeout_show(struct kobject *kobj, - struct kobj_attribute *attr, +static ssize_t sleep_timeout_show(struct device *dev, + struct device_attribute *attr, char *buf) { - return sprintf(buf, "%u\n", sleep_timeout / HZ); + struct platform_device *pdev = container_of(dev, + struct platform_device, dev); + struct omap_uart_state *uart = container_of(pdev, + struct omap_uart_state, pdev); + + return sprintf(buf, "%u\n", uart->timeout / HZ); } -static ssize_t sleep_timeout_store(struct kobject *kobj, - struct kobj_attribute *attr, +static ssize_t sleep_timeout_store(struct device *dev, + struct device_attribute *attr, const char *buf, size_t n) { - struct omap_uart_state *uart; + struct platform_device *pdev = container_of(dev, + struct platform_device, dev); + struct omap_uart_state *uart = container_of(pdev, + struct omap_uart_state, pdev); unsigned int value; if (sscanf(buf, "%u", &value) != 1) { printk(KERN_ERR "sleep_timeout_store: Invalid value\n"); return -EINVAL; } - sleep_timeout = value * HZ; - list_for_each_entry(uart, &uart_list, node) { - uart->timeout = sleep_timeout; - if (uart->timeout) - mod_timer(&uart->timer, jiffies + uart->timeout); - else - /* A zero value means disable timeout feature */ - omap_uart_block_sleep(uart); - } + + uart->timeout = value * HZ; + if (uart->timeout) + mod_timer(&uart->timer, jiffies + uart->timeout); + else + /* A zero value means disable timeout feature */ + omap_uart_block_sleep(uart); + return n; } -static struct kobj_attribute sleep_timeout_attr = - __ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store); - +DEVICE_ATTR(sleep_timeout, 0644, sleep_timeout_show, sleep_timeout_store); +#define DEV_CREATE_FILE(dev, attr) WARN_ON(device_create_file(dev, attr)) #else static inline void omap_uart_idle_init(struct omap_uart_state *uart) {} +#define DEV_CREATE_FILE(dev, attr) #endif /* CONFIG_PM */ -static struct platform_device serial_device = { - .name = "serial8250", - .id = PLAT8250_DEV_PLATFORM, - .dev = { - .platform_data = serial_platform_data, +static struct omap_uart_state omap_uart[OMAP_MAX_NR_PORTS] = { + { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM, + .dev = { + .platform_data = serial_platform_data0, + }, + }, + }, { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM1, + .dev = { + .platform_data = serial_platform_data1, + }, + }, + }, { + .pdev = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM2, + .dev = { + .platform_data = serial_platform_data2, + }, + }, }, }; void __init omap_serial_init(void) { - int i, err; + int i; const struct omap_uart_config *info; char name[16]; @@ -512,8 +570,10 @@ void __init omap_serial_init(void) return; for (i = 0; i < OMAP_MAX_NR_PORTS; i++) { - struct plat_serial8250_port *p = serial_platform_data + i; struct omap_uart_state *uart = &omap_uart[i]; + struct platform_device *pdev = &uart->pdev; + struct device *dev = &pdev->dev; + struct plat_serial8250_port *p = dev->platform_data; if (!(info->enabled_uarts & (1 << i))) { p->membase = NULL; @@ -549,15 +609,13 @@ void __init omap_serial_init(void) omap_uart_enable_clocks(uart); omap_uart_reset(uart); omap_uart_idle_init(uart); - } - - err = platform_device_register(&serial_device); - -#ifdef CONFIG_PM - if (!err) - err = sysfs_create_file(&serial_device.dev.kobj, - &sleep_timeout_attr.attr); -#endif + if (WARN_ON(platform_device_register(pdev))) + continue; + if ((cpu_is_omap34xx() && uart->padconf) || + (uart->wk_en && uart->wk_mask)) { + device_init_wakeup(dev, true); + DEV_CREATE_FILE(dev, &dev_attr_sleep_timeout); + } + } } - -- cgit v1.2.3-70-g09d2 From bcf396c48012a5e4c7ab77be5c40df10d6bdb8ad Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Tue, 30 Jun 2009 21:02:45 -0700 Subject: OMAP2/3/4: UART: allow in-order port traversal Use list_add_tail() when adding discovered UART ports. This is so traversal using list_for_each_entry() will traverse the list in the order they were found. Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/serial.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/serial.c b/arch/arm/mach-omap2/serial.c index 6f35a7e4893..a7421a50410 100644 --- a/arch/arm/mach-omap2/serial.c +++ b/arch/arm/mach-omap2/serial.c @@ -601,7 +601,7 @@ void __init omap_serial_init(void) uart->num = i; p->private_data = uart; uart->p = p; - list_add(&uart->node, &uart_list); + list_add_tail(&uart->node, &uart_list); if (cpu_is_omap44xx()) p->irq += 32; -- cgit v1.2.3-70-g09d2 From 6c5f80393b107b0c9e2a54b03b65d1880e706655 Mon Sep 17 00:00:00 2001 From: Jouni Hogander Date: Wed, 29 Oct 2008 12:06:04 +0200 Subject: OMAP3: PM: Fix wrong sequence in suspend. Powerdomain previous state is checked after restoring new states in suspend. This patch fixes this problem. Signed-off-by: Jouni Hogander Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/pm34xx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/pm34xx.c b/arch/arm/mach-omap2/pm34xx.c index b07efb26de1..488d595d8e4 100644 --- a/arch/arm/mach-omap2/pm34xx.c +++ b/arch/arm/mach-omap2/pm34xx.c @@ -326,7 +326,6 @@ static int omap3_pm_suspend(void) restore: /* Restore next_pwrsts */ list_for_each_entry(pwrst, &pwrst_list, node) { - set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state); state = pwrdm_read_prev_pwrst(pwrst->pwrdm); if (state > pwrst->next_state) { printk(KERN_INFO "Powerdomain (%s) didn't enter " @@ -334,6 +333,7 @@ restore: pwrst->pwrdm->name, pwrst->next_state); ret = -1; } + set_pwrdm_state(pwrst->pwrdm, pwrst->saved_state); } if (ret) printk(KERN_ERR "Could not enter target state in pm_suspend\n"); -- cgit v1.2.3-70-g09d2 From 6fd210a9cc398ecbff7bcdbe220651b73b654f56 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Mon, 20 Jul 2009 09:09:23 -0700 Subject: OMAP3: Overo: add missing pen-down GPIO definition Signed-off-by: Kevin Hilman --- arch/arm/mach-omap2/board-overo.c | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index dff5528fbfb..e26af837510 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -51,6 +51,7 @@ #define OVERO_GPIO_BT_XGATE 15 #define OVERO_GPIO_W2W_NRESET 16 +#define OVERO_GPIO_PENDOWN 114 #define OVERO_GPIO_BT_NRESET 164 #define OVERO_GPIO_USBH_CPEN 168 #define OVERO_GPIO_USBH_NRESET 183 -- cgit v1.2.3-70-g09d2 From e8e2ff462dd92693f29eb848f42d3eb720390d59 Mon Sep 17 00:00:00 2001 From: "Gupta, Ajay Kumar" Date: Wed, 29 Jul 2009 11:58:57 +0530 Subject: USB: musb: fix the nop registration for OMAP3EVM OMAP3EVM uses ISP1504 phy which doesn't require any programming and thus has to use NOP otg transceiver. Cleanups being done: - Remove unwanted code in usb-musb.c file - Register NOP in OMAP3EVM board file using usb_nop_xceiv_register(). - Select NOP_USB_XCEIV for OMAP3EVM boards. - Don't enable TWL4030_USB in omap3_evm_defconfig Signed-off-by: Ajay Kumar Gupta Signed-off-by: Eino-Ville Talvala Acked-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- arch/arm/configs/omap3_evm_defconfig | 2 +- arch/arm/mach-omap2/board-omap3evm.c | 5 +++++ arch/arm/mach-omap2/usb-musb.c | 21 --------------------- drivers/usb/musb/Kconfig | 1 + 4 files changed, 7 insertions(+), 22 deletions(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/configs/omap3_evm_defconfig b/arch/arm/configs/omap3_evm_defconfig index 28be17fbc15..d5ff4776cd0 100644 --- a/arch/arm/configs/omap3_evm_defconfig +++ b/arch/arm/configs/omap3_evm_defconfig @@ -1107,7 +1107,7 @@ CONFIG_USB_ZERO=m CONFIG_USB_OTG_UTILS=y # CONFIG_USB_GPIO_VBUS is not set # CONFIG_ISP1301_OMAP is not set -CONFIG_TWL4030_USB=y +# CONFIG_TWL4030_USB is not set # CONFIG_NOP_USB_XCEIV is not set CONFIG_MMC=y # CONFIG_MMC_DEBUG is not set diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index d3cc145814d..cf3dd771a67 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -25,6 +25,7 @@ #include #include #include +#include #include #include @@ -307,6 +308,10 @@ static void __init omap3_evm_init(void) ARRAY_SIZE(omap3evm_spi_board_info)); omap_serial_init(); +#ifdef CONFIG_NOP_USB_XCEIV + /* OMAP3EVM uses ISP1504 phy and so register nop transceiver */ + usb_nop_xceiv_register(); +#endif usb_musb_init(); ads7846_dev_init(); } diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c index d85296dc896..739e59e8025 100644 --- a/arch/arm/mach-omap2/usb-musb.c +++ b/arch/arm/mach-omap2/usb-musb.c @@ -155,20 +155,6 @@ static struct platform_device musb_device = { .resource = musb_resources, }; -#ifdef CONFIG_NOP_USB_XCEIV -static u64 nop_xceiv_dmamask = DMA_BIT_MASK(32); - -static struct platform_device nop_xceiv_device = { - .name = "nop_usb_xceiv", - .id = -1, - .dev = { - .dma_mask = &nop_xceiv_dmamask, - .coherent_dma_mask = DMA_BIT_MASK(32), - .platform_data = NULL, - }, -}; -#endif - void __init usb_musb_init(void) { if (cpu_is_omap243x()) @@ -183,13 +169,6 @@ void __init usb_musb_init(void) */ musb_plat.clock = "ick"; -#ifdef CONFIG_NOP_USB_XCEIV - if (platform_device_register(&nop_xceiv_device) < 0) { - printk(KERN_ERR "Unable to register NOP-XCEIV device\n"); - return; - } -#endif - if (platform_device_register(&musb_device) < 0) { printk(KERN_ERR "Unable to register HS-USB (MUSB) device\n"); return; diff --git a/drivers/usb/musb/Kconfig b/drivers/usb/musb/Kconfig index 70073b157f0..803adcb5ac1 100644 --- a/drivers/usb/musb/Kconfig +++ b/drivers/usb/musb/Kconfig @@ -12,6 +12,7 @@ config USB_MUSB_HDRC depends on !SUPERH select NOP_USB_XCEIV if ARCH_DAVINCI select TWL4030_USB if MACH_OMAP_3430SDP + select NOP_USB_XCEIV if MACH_OMAP3EVM select USB_OTG_UTILS tristate 'Inventra Highspeed Dual Role Controller (TI, ADI, ...)' help -- cgit v1.2.3-70-g09d2 From 5032902c331acc71956e47abd90d090181c5ef4a Mon Sep 17 00:00:00 2001 From: Sergio Aguirre Date: Mon, 10 Aug 2009 14:49:50 +0300 Subject: OMAP3: Overo: Fix smsc911x platform device resource value Fixes a wrong setting of resource parameter list in SMSC911x platform driver data structure for Overo case. This fixes folowing warning when compiling for Overo board: warning: initialization from incompatible pointer type Introduced since commit id: commit 172ef275444efa12d834fb9d1b1acdac92db47f7 Author: Steve Sakoman Date: Mon Feb 2 06:27:49 2009 +0000 ARM: Add SMSC911X support to Overo platform (V2) Signed-off-by: Sergio Aguirre Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-overo.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index dff5528fbfb..fec1bb19b9f 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -146,7 +146,7 @@ static struct platform_device overo_smsc911x_device = { .name = "smsc911x", .id = -1, .num_resources = ARRAY_SIZE(overo_smsc911x_resources), - .resource = &overo_smsc911x_resources, + .resource = overo_smsc911x_resources, .dev = { .platform_data = &overo_smsc911x_config, }, -- cgit v1.2.3-70-g09d2 From dfc27b34496923b5f552eb9cdf20468045114ada Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 10 Aug 2009 14:49:51 +0300 Subject: OMAP3: RX51: Define TWL4030 USB transceiver in board file Add OTG transceiver to RX51 platform data to prevent kernel NULL pointer dereference during MUSB initialisation. Signed-off-by: Roger Quadros Signed-off-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-rx51-peripherals.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/board-rx51-peripherals.c b/arch/arm/mach-omap2/board-rx51-peripherals.c index 9a0bf6744a0..56d931a425f 100644 --- a/arch/arm/mach-omap2/board-rx51-peripherals.c +++ b/arch/arm/mach-omap2/board-rx51-peripherals.c @@ -278,6 +278,10 @@ static struct twl4030_gpio_platform_data rx51_gpio_data = { .setup = rx51_twlgpio_setup, }; +static struct twl4030_usb_data rx51_usb_data = { + .usb_mode = T2_USB_MODE_ULPI, +}; + static struct twl4030_platform_data rx51_twldata = { .irq_base = TWL4030_IRQ_BASE, .irq_end = TWL4030_IRQ_END, @@ -286,6 +290,7 @@ static struct twl4030_platform_data rx51_twldata = { .gpio = &rx51_gpio_data, .keypad = &rx51_kp_data, .madc = &rx51_madc_data, + .usb = &rx51_usb_data, .vaux1 = &rx51_vaux1, .vaux2 = &rx51_vaux2, -- cgit v1.2.3-70-g09d2 From 22833044fbe2764d44ae03f58508e671652ca186 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Mon, 10 Aug 2009 14:49:51 +0300 Subject: OMAP2/3: mmc-twl4030: Free up MMC regulators while cleaning up twl_mmc_cleanup() must free up the regulators that were allocated by twl_mmc_late_init(). This eliminates the below error when 'omap_hsmmc' module is repeatedly loaded and unloaded. "sysfs: cannot create duplicate filename '/devices/platform /mmci-omap-hs.0/microamps_requested_vmmc'" Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/mmc-twl4030.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm/mach-omap2') diff --git a/arch/arm/mach-omap2/mmc-twl4030.c b/arch/arm/mach-omap2/mmc-twl4030.c index 1541fd4c8d0..3c04c2f1b23 100644 --- a/arch/arm/mach-omap2/mmc-twl4030.c +++ b/arch/arm/mach-omap2/mmc-twl4030.c @@ -119,6 +119,7 @@ static int twl_mmc_late_init(struct device *dev) if (i != 0) break; ret = PTR_ERR(reg); + hsmmc[i].vcc = NULL; goto err; } hsmmc[i].vcc = reg; @@ -165,8 +166,13 @@ done: static void twl_mmc_cleanup(struct device *dev) { struct omap_mmc_platform_data *mmc = dev->platform_data; + int i; gpio_free(mmc->slots[0].switch_pin); + for(i = 0; i < ARRAY_SIZE(hsmmc); i++) { + regulator_put(hsmmc[i].vcc); + regulator_put(hsmmc[i].vcc_aux); + } } #ifdef CONFIG_PM -- cgit v1.2.3-70-g09d2