From cc890cd78acd7ab03442907d354b6af34e973cb3 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Thu, 8 Sep 2011 09:04:51 +0100 Subject: ARM: 7083/1: rewrite U300 GPIO to use gpiolib This rewrites the U300 GPIO so as to use gpiolib and struct gpio_chip instead of just generic GPIO, hiding all the platform specifics and passing in GPIO chip variant as platform data at runtime instead of the compiletime kludges. As a result is now empty for U300 and using just defaults. Cc: Grant Likely Cc: Debian kernel maintainers Cc: Arnaud Patard Reported-by: Ben Hutchings Signed-off-by: Linus Walleij Signed-off-by: Russell King --- arch/arm/mach-u300/include/mach/gpio-u300.h | 149 +++++----------------------- 1 file changed, 23 insertions(+), 126 deletions(-) (limited to 'arch/arm/mach-u300/include/mach/gpio-u300.h') diff --git a/arch/arm/mach-u300/include/mach/gpio-u300.h b/arch/arm/mach-u300/include/mach/gpio-u300.h index a6119062add..0c2b2021951 100644 --- a/arch/arm/mach-u300/include/mach/gpio-u300.h +++ b/arch/arm/mach-u300/include/mach/gpio-u300.h @@ -9,132 +9,6 @@ #ifndef __MACH_U300_GPIO_U300_H #define __MACH_U300_GPIO_U300_H -#include -#include -#include -#include - -/* Switch type depending on platform/chip variant */ -#if defined(CONFIG_MACH_U300_BS2X) || defined(CONFIG_MACH_U300_BS330) -#define U300_COH901335 -#endif -#if defined(CONFIG_MACH_U300_BS365) || defined(CONFIG_MACH_U300_BS335) -#define U300_COH901571_3 -#endif - -/* Get base address for regs here */ -#include "u300-regs.h" -/* IRQ numbers */ -#include "irqs.h" - -/* - * This is the GPIO block definitions. GPIO (General Purpose I/O) can be - * used for anything, and often is. The event/enable etc figures are for - * the lowermost pin (pin 0 on each port), shift this left to match your - * pin if you're gonna use these values. - */ -#ifdef U300_COH901335 -#define U300_GPIO_PORTX_SPACING (0x1C) -/* Port X Pin Data Register 32bit, this is both input and output (R/W) */ -#define U300_GPIO_PXPDIR (0x00) -#define U300_GPIO_PXPDOR (0x00) -/* Port X Pin Config Register 32bit (R/W) */ -#define U300_GPIO_PXPCR (0x04) -#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL) -#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL) -#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL) -#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL) -#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL) -#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL) -#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL) -/* Port X Interrupt Event Register 32bit (R/W) */ -#define U300_GPIO_PXIEV (0x08) -#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK (0x000000FFUL) -#define U300_GPIO_PXIEV_IRQ_EVENT (0x00000001UL) -/* Port X Interrupt Enable Register 32bit (R/W) */ -#define U300_GPIO_PXIEN (0x0C) -#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK (0x000000FFUL) -#define U300_GPIO_PXIEN_IRQ_ENABLE (0x00000001UL) -/* Port X Interrupt Force Register 32bit (R/W) */ -#define U300_GPIO_PXIFR (0x10) -#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK (0x000000FFUL) -#define U300_GPIO_PXIFR_IRQ_FORCE (0x00000001UL) -/* Port X Interrupt Config Register 32bit (R/W) */ -#define U300_GPIO_PXICR (0x14) -#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL) -#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL) -#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL) -#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL) -/* Port X Pull-up Enable Register 32bit (R/W) */ -#define U300_GPIO_PXPER (0x18) -#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL) -#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL) -/* Control Register 32bit (R/W) */ -#define U300_GPIO_CR (0x54) -#define U300_GPIO_CR_BLOCK_CLOCK_ENABLE (0x00000001UL) -/* three ports of 8 bits each = GPIO pins 0..23 */ -#define U300_GPIO_NUM_PORTS 3 -#define U300_GPIO_PINS_PER_PORT 8 -#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1) -#endif - -#ifdef U300_COH901571_3 -/* - * Control Register 32bit (R/W) - * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores - * gives the number of GPIO pins. - * bit 8-2 (mask 0x000001FC) contains the core version ID. - */ -#define U300_GPIO_CR (0x00) -#define U300_GPIO_CR_SYNC_SEL_ENABLE (0x00000002UL) -#define U300_GPIO_CR_BLOCK_CLKRQ_ENABLE (0x00000001UL) -#define U300_GPIO_PORTX_SPACING (0x30) -/* Port X Pin Data INPUT Register 32bit (R/W) */ -#define U300_GPIO_PXPDIR (0x04) -/* Port X Pin Data OUTPUT Register 32bit (R/W) */ -#define U300_GPIO_PXPDOR (0x08) -/* Port X Pin Config Register 32bit (R/W) */ -#define U300_GPIO_PXPCR (0x0C) -#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK (0x0000FFFFUL) -#define U300_GPIO_PXPCR_PIN_MODE_MASK (0x00000003UL) -#define U300_GPIO_PXPCR_PIN_MODE_SHIFT (0x00000002UL) -#define U300_GPIO_PXPCR_PIN_MODE_INPUT (0x00000000UL) -#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL (0x00000001UL) -#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN (0x00000002UL) -#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE (0x00000003UL) -/* Port X Pull-up Enable Register 32bit (R/W) */ -#define U300_GPIO_PXPER (0x10) -#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK (0x000000FFUL) -#define U300_GPIO_PXPER_PULL_UP_DISABLE (0x00000001UL) -/* Port X Interrupt Event Register 32bit (R/W) */ -#define U300_GPIO_PXIEV (0x14) -#define U300_GPIO_PXIEV_ALL_IRQ_EVENT_MASK (0x000000FFUL) -#define U300_GPIO_PXIEV_IRQ_EVENT (0x00000001UL) -/* Port X Interrupt Enable Register 32bit (R/W) */ -#define U300_GPIO_PXIEN (0x18) -#define U300_GPIO_PXIEN_ALL_IRQ_ENABLE_MASK (0x000000FFUL) -#define U300_GPIO_PXIEN_IRQ_ENABLE (0x00000001UL) -/* Port X Interrupt Force Register 32bit (R/W) */ -#define U300_GPIO_PXIFR (0x1C) -#define U300_GPIO_PXIFR_ALL_IRQ_FORCE_MASK (0x000000FFUL) -#define U300_GPIO_PXIFR_IRQ_FORCE (0x00000001UL) -/* Port X Interrupt Config Register 32bit (R/W) */ -#define U300_GPIO_PXICR (0x20) -#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK (0x000000FFUL) -#define U300_GPIO_PXICR_IRQ_CONFIG_MASK (0x00000001UL) -#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE (0x00000000UL) -#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE (0x00000001UL) -#ifdef CONFIG_MACH_U300_BS335 -/* seven ports of 8 bits each = GPIO pins 0..55 */ -#define U300_GPIO_NUM_PORTS 7 -#else -/* five ports of 8 bits each = GPIO pins 0..39 */ -#define U300_GPIO_NUM_PORTS 5 -#endif -#define U300_GPIO_PINS_PER_PORT 8 -#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * U300_GPIO_NUM_PORTS - 1) -#endif - /* * Individual pin assignments for the B26/S26. Notice that the * actual usage of these pins depends on the PAD MUX settings, that @@ -250,4 +124,27 @@ #endif +/** + * enum u300_gpio_variant - the type of U300 GPIO employed + */ +enum u300_gpio_variant { + U300_GPIO_COH901335, + U300_GPIO_COH901571_3_BS335, + U300_GPIO_COH901571_3_BS365, +}; + +/** + * struct u300_gpio_platform - U300 GPIO platform data + * @variant: IP block variant + * @ports: number of GPIO block ports + * @gpio_base: first GPIO number for this block (use a free range) + * @gpio_irq_base: first GPIO IRQ number for this block (use a free range) + */ +struct u300_gpio_platform { + enum u300_gpio_variant variant; + u8 ports; + int gpio_base; + int gpio_irq_base; +}; + #endif /* __MACH_U300_GPIO_U300_H */ -- cgit v1.2.3-70-g09d2