From 438ff3f3cc33833206a48492e9d6674e4e82bed8 Mon Sep 17 00:00:00 2001 From: Haavard Skinnemoen Date: Mon, 29 Oct 2007 15:28:07 +0100 Subject: [AVR32] Add support for AT32AP7001 and AT32AP7002 These are derivatives of the AT32AP7000 chip, which means that most of the code stays the same. Rename a few files, functions, definitions and config symbols to reflect that they apply to all AP700x chips, and exclude some platform devices from chips where they aren't present. Signed-off-by: Haavard Skinnemoen --- arch/avr32/boards/atngw100/setup.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/avr32/boards') diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c index 52987c81d66..a398be28496 100644 --- a/arch/avr32/boards/atngw100/setup.c +++ b/arch/avr32/boards/atngw100/setup.c @@ -20,7 +20,7 @@ #include #include -#include +#include #include #include #include -- cgit v1.2.3-70-g09d2 From f4c41b2689eec03bd4f8145a08903862673e002b Mon Sep 17 00:00:00 2001 From: Haavard Skinnemoen Date: Mon, 29 Oct 2007 16:02:51 +0100 Subject: [AVR32] ATSTK1000: Move gpio-leds setup to setup.c There may be other boards than STK1002 that want to use the leds on STK1000. Move it to stk1000 common code to make it easier to reuse. Signed-off-by: Haavard Skinnemoen --- arch/avr32/boards/atstk1000/Kconfig | 8 ++--- arch/avr32/boards/atstk1000/atstk1000.h | 2 ++ arch/avr32/boards/atstk1000/atstk1002.c | 64 ++------------------------------- arch/avr32/boards/atstk1000/setup.c | 64 +++++++++++++++++++++++++++++++++ 4 files changed, 72 insertions(+), 66 deletions(-) (limited to 'arch/avr32/boards') diff --git a/arch/avr32/boards/atstk1000/Kconfig b/arch/avr32/boards/atstk1000/Kconfig index 718578f6406..dcf9e9e2b28 100644 --- a/arch/avr32/boards/atstk1000/Kconfig +++ b/arch/avr32/boards/atstk1000/Kconfig @@ -50,9 +50,9 @@ config BOARD_ATSTK1002_SPI1 GPIO lines and accessed through the J1 jumper block. Say "y" here to configure that SPI controller. -config BOARD_ATSTK1002_J2_LED +config BOARD_ATSTK1000_J2_LED bool - default BOARD_ATSTK1002_J2_LED8 || BOARD_ATSTK1002_J2_RGB + default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB choice prompt "LEDs connected to J2:" @@ -64,12 +64,12 @@ choice IDC cable. A default "heartbeat" trigger is provided, but you can of course override this. -config BOARD_ATSTK1002_J2_LED8 +config BOARD_ATSTK1000_J2_LED8 bool "LED0..LED7" help Select this if J2 is jumpered to LED0..LED7 amber leds. -config BOARD_ATSTK1002_J2_RGB +config BOARD_ATSTK1000_J2_RGB bool "RGB leds" help Select this if J2 is jumpered to the RGB leds. diff --git a/arch/avr32/boards/atstk1000/atstk1000.h b/arch/avr32/boards/atstk1000/atstk1000.h index 9a49ed036b7..9392d325286 100644 --- a/arch/avr32/boards/atstk1000/atstk1000.h +++ b/arch/avr32/boards/atstk1000/atstk1000.h @@ -12,4 +12,6 @@ extern struct atmel_lcdfb_info atstk1000_lcdc_data; +void atstk1000_setup_j2_leds(void); + #endif /* __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H */ diff --git a/arch/avr32/boards/atstk1000/atstk1002.c b/arch/avr32/boards/atstk1000/atstk1002.c index 5be0d13f4b0..2481d238987 100644 --- a/arch/avr32/boards/atstk1000/atstk1002.c +++ b/arch/avr32/boards/atstk1000/atstk1002.c @@ -11,7 +11,6 @@ #include #include #include -#include #include #include #include @@ -22,7 +21,7 @@ #include #include -#include +#include #include #include #include @@ -141,65 +140,6 @@ static void __init set_hw_addr(struct platform_device *pdev) clk_put(pclk); } -#ifdef CONFIG_BOARD_ATSTK1002_J2_LED - -static struct gpio_led stk_j2_led[] = { -#ifdef CONFIG_BOARD_ATSTK1002_J2_LED8 -#define LEDSTRING "J2 jumpered to LED8" - { .name = "led0:amber", .gpio = GPIO_PIN_PB( 8), }, - { .name = "led1:amber", .gpio = GPIO_PIN_PB( 9), }, - { .name = "led2:amber", .gpio = GPIO_PIN_PB(10), }, - { .name = "led3:amber", .gpio = GPIO_PIN_PB(13), }, - { .name = "led4:amber", .gpio = GPIO_PIN_PB(14), }, - { .name = "led5:amber", .gpio = GPIO_PIN_PB(15), }, - { .name = "led6:amber", .gpio = GPIO_PIN_PB(16), }, - { .name = "led7:amber", .gpio = GPIO_PIN_PB(30), - .default_trigger = "heartbeat", }, -#else /* RGB */ -#define LEDSTRING "J2 jumpered to RGB LEDs" - { .name = "r1:red", .gpio = GPIO_PIN_PB( 8), }, - { .name = "g1:green", .gpio = GPIO_PIN_PB(10), }, - { .name = "b1:blue", .gpio = GPIO_PIN_PB(14), }, - - { .name = "r2:red", .gpio = GPIO_PIN_PB( 9), - .default_trigger = "heartbeat", }, - { .name = "g2:green", .gpio = GPIO_PIN_PB(13), }, - { .name = "b2:blue", .gpio = GPIO_PIN_PB(15), - .default_trigger = "heartbeat", }, - /* PB16, PB30 unused */ -#endif -}; - -static struct gpio_led_platform_data stk_j2_led_data = { - .num_leds = ARRAY_SIZE(stk_j2_led), - .leds = stk_j2_led, -}; - -static struct platform_device stk_j2_led_dev = { - .name = "leds-gpio", - .id = 2, /* gpio block J2 */ - .dev = { - .platform_data = &stk_j2_led_data, - }, -}; - -static void setup_j2_leds(void) -{ - unsigned i; - - for (i = 0; i < ARRAY_SIZE(stk_j2_led); i++) - at32_select_gpio(stk_j2_led[i].gpio, AT32_GPIOF_OUTPUT); - - printk("STK1002: " LEDSTRING "\n"); - platform_device_register(&stk_j2_led_dev); -} - -#else -static void setup_j2_leds(void) -{ -} -#endif - #ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM #ifndef CONFIG_BOARD_ATSTK1002_SW3_CUSTOM static void __init at73c213_set_clk(struct at73c213_board_info *info) @@ -298,7 +238,7 @@ static int __init atstk1002_init(void) at32_add_device_ssc(0, ATMEL_SSC_TX); #endif - setup_j2_leds(); + atstk1000_setup_j2_leds(); #ifndef CONFIG_BOARD_ATSTK1002_SW3_CUSTOM #ifndef CONFIG_BOARD_ATSTK1002_SW1_CUSTOM diff --git a/arch/avr32/boards/atstk1000/setup.c b/arch/avr32/boards/atstk1000/setup.c index c9af409ada9..8bedf93876a 100644 --- a/arch/avr32/boards/atstk1000/setup.c +++ b/arch/avr32/boards/atstk1000/setup.c @@ -10,13 +10,17 @@ #include #include #include +#include #include #include #include