From 6bd1fbea2e8bff9346a5afb44ca948b4e4ed74a5 Mon Sep 17 00:00:00 2001 From: Sonic Zhang Date: Wed, 9 Sep 2009 10:46:19 +0000 Subject: Blackfin: move on-chip UART resources to boards files Rather than keeping the pins in the actual driver and worrying about a mess of Kconfig options, declare all the desired pin resources in the boards file. This lets people easily select the specific pins/ports for the normal UART as well as GPIOs for CTS/RTS. Signed-off-by: Sonic Zhang Signed-off-by: Mike Frysinger --- arch/blackfin/mach-bf533/boards/blackstamp.c | 47 +++++++++++++++++++++++----- 1 file changed, 39 insertions(+), 8 deletions(-) (limited to 'arch/blackfin/mach-bf533/boards/blackstamp.c') diff --git a/arch/blackfin/mach-bf533/boards/blackstamp.c b/arch/blackfin/mach-bf533/boards/blackstamp.c index b580884848d..50ce3ecfdcb 100644 --- a/arch/blackfin/mach-bf533/boards/blackstamp.c +++ b/arch/blackfin/mach-bf533/boards/blackstamp.c @@ -195,21 +195,50 @@ static struct platform_device bfin_spi0_device = { #endif /* spi master and devices */ #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) -static struct resource bfin_uart_resources[] = { +#ifdef CONFIG_SERIAL_BFIN_UART0 +static struct resource bfin_uart0_resources[] = { { - .start = 0xFFC00400, - .end = 0xFFC004FF, + .start = BFIN_UART_THR, + .end = BFIN_UART_GCTL+2, .flags = IORESOURCE_MEM, }, + { + .start = IRQ_UART0_RX, + .end = IRQ_UART0_RX + 1, + .flags = IORESOURCE_IRQ, + }, + { + .start = IRQ_UART0_ERROR, + .end = IRQ_UART0_ERROR, + .flags = IORESOURCE_IRQ, + }, + { + .start = CH_UART0_TX, + .end = CH_UART0_TX, + .flags = IORESOURCE_DMA, + }, + { + .start = CH_UART0_RX, + .end = CH_UART0_RX, + .flags = IORESOURCE_DMA, + }, +}; + +unsigned short bfin_uart0_peripherals[] = { + P_UART0_TX, P_UART0_RX, 0 }; -static struct platform_device bfin_uart_device = { +static struct platform_device bfin_uart0_device = { .name = "bfin-uart", - .id = 1, - .num_resources = ARRAY_SIZE(bfin_uart_resources), - .resource = bfin_uart_resources, + .id = 0, + .num_resources = ARRAY_SIZE(bfin_uart0_resources), + .resource = bfin_uart0_resources, + .dev = { + .platform_data = &bfin_uart0_peripherals, /* Passed to driver */ + }, }; #endif +#endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) #ifdef CONFIG_BFIN_SIR0 @@ -344,7 +373,9 @@ static struct platform_device *stamp_devices[] __initdata = { #endif #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE) - &bfin_uart_device, +#ifdef CONFIG_SERIAL_BFIN_UART0 + &bfin_uart0_device, +#endif #endif #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE) -- cgit v1.2.3-70-g09d2