From abf1e27fbb4200a010b8fcb1be8cc02485744862 Mon Sep 17 00:00:00 2001 From: John Bonesio Date: Wed, 17 Nov 2010 15:28:30 -0800 Subject: powerpc/5200: dts: rename nodes to prepare for refactoring dts files This patch renames nodes in dts fils for MPC5200b files to prepare for refactoring of these files later. When refactoring it will be easier to verify the results if the node names aren't changing at the same time. Signed-off-by: John Bonesio Signed-off-by: Grant Likely --- arch/powerpc/boot/dts/cm5200.dts | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'arch/powerpc/boot/dts/cm5200.dts') diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts index dd3860846f1..9369dcd00a5 100644 --- a/arch/powerpc/boot/dts/cm5200.dts +++ b/arch/powerpc/boot/dts/cm5200.dts @@ -160,25 +160,25 @@ reg = <0x1f00 0x100>; }; - serial@2000 { // PSC1 + psc@2000 { // PSC1 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; reg = <0x2000 0x100>; interrupts = <2 1 0>; }; - serial@2200 { // PSC2 + psc@2200 { // PSC2 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; reg = <0x2200 0x100>; interrupts = <2 2 0>; }; - serial@2400 { // PSC3 + psc@2400 { // PSC3 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; reg = <0x2400 0x100>; interrupts = <2 3 0>; }; - serial@2c00 { // PSC6 + psc@2c00 { // PSC6 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; reg = <0x2c00 0x100>; interrupts = <2 4 0>; -- cgit v1.2.3-70-g09d2 From 6847317377c871c6e7a8d54e5849bcd0f9b11eb4 Mon Sep 17 00:00:00 2001 From: John Bonesio Date: Wed, 17 Nov 2010 15:28:39 -0800 Subject: powerpc/5200: dts: remove unused properties This patch remove unused properties in dts files in preparation of refactoring the dts files for MPC5200b based boards. Signed-off-by: John Bonesio Signed-off-by: Grant Likely --- arch/powerpc/boot/dts/cm5200.dts | 2 -- arch/powerpc/boot/dts/lite5200b.dts | 3 --- arch/powerpc/boot/dts/media5200.dts | 2 -- arch/powerpc/boot/dts/motionpro.dts | 2 -- arch/powerpc/boot/dts/pcm030.dts | 2 -- arch/powerpc/boot/dts/pcm032.dts | 2 -- 6 files changed, 13 deletions(-) (limited to 'arch/powerpc/boot/dts/cm5200.dts') diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts index 9369dcd00a5..d549897b7eb 100644 --- a/arch/powerpc/boot/dts/cm5200.dts +++ b/arch/powerpc/boot/dts/cm5200.dts @@ -230,8 +230,6 @@ reg = <0 0 0x2000000>; bank-width = <2>; device-width = <2>; - #size-cells = <1>; - #address-cells = <1>; }; }; }; diff --git a/arch/powerpc/boot/dts/lite5200b.dts b/arch/powerpc/boot/dts/lite5200b.dts index a74b7908405..c0a4e4592ba 100644 --- a/arch/powerpc/boot/dts/lite5200b.dts +++ b/arch/powerpc/boot/dts/lite5200b.dts @@ -174,7 +174,6 @@ psc@2000 { // PSC1 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - cell-index = <0>; reg = <0x2000 0x100>; interrupts = <2 1 0>; }; @@ -198,7 +197,6 @@ // PSC4 in uart mode example //serial@2600 { // PSC4 // compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - // cell-index = <3>; // reg = <0x2600 0x100>; // interrupts = <2 11 0>; //}; @@ -206,7 +204,6 @@ // PSC5 in uart mode example //serial@2800 { // PSC5 // compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - // cell-index = <4>; // reg = <0x2800 0x100>; // interrupts = <2 12 0>; //}; diff --git a/arch/powerpc/boot/dts/media5200.dts b/arch/powerpc/boot/dts/media5200.dts index a70ef680f30..e027f459c23 100644 --- a/arch/powerpc/boot/dts/media5200.dts +++ b/arch/powerpc/boot/dts/media5200.dts @@ -185,8 +185,6 @@ // PSC6 in uart mode console: psc@2c00 { // PSC6 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - cell-index = <5>; - port-number = <0>; // Logical port assignment reg = <0x2c00 0x100>; interrupts = <2 4 0>; }; diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts index f6261ea0972..3ab4666c994 100644 --- a/arch/powerpc/boot/dts/motionpro.dts +++ b/arch/powerpc/boot/dts/motionpro.dts @@ -277,8 +277,6 @@ reg = <0 0 0x01000000>; bank-width = <2>; device-width = <2>; - #size-cells = <1>; - #address-cells = <1>; }; }; }; diff --git a/arch/powerpc/boot/dts/pcm030.dts b/arch/powerpc/boot/dts/pcm030.dts index 34ab3bbcf99..28d77758d8b 100644 --- a/arch/powerpc/boot/dts/pcm030.dts +++ b/arch/powerpc/boot/dts/pcm030.dts @@ -196,7 +196,6 @@ psc@2400 { /* PSC3 in UART mode */ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - cell-index = <2>; reg = <0x2400 0x100>; interrupts = <2 3 0>; }; @@ -207,7 +206,6 @@ psc@2c00 { /* PSC6 in UART mode */ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - cell-index = <5>; reg = <0x2c00 0x100>; interrupts = <2 4 0>; }; diff --git a/arch/powerpc/boot/dts/pcm032.dts b/arch/powerpc/boot/dts/pcm032.dts index 29fde83b99b..9dee52b6747 100644 --- a/arch/powerpc/boot/dts/pcm032.dts +++ b/arch/powerpc/boot/dts/pcm032.dts @@ -196,7 +196,6 @@ psc@2400 { /* PSC3 in UART mode */ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - cell-index = <2>; reg = <0x2400 0x100>; interrupts = <2 3 0>; }; @@ -207,7 +206,6 @@ psc@2c00 { /* PSC6 in UART mode */ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - cell-index = <5>; reg = <0x2c00 0x100>; interrupts = <2 4 0>; }; -- cgit v1.2.3-70-g09d2 From 11946c826d02a16521edc777d88470a6a0fe1441 Mon Sep 17 00:00:00 2001 From: John Bonesio Date: Wed, 17 Nov 2010 15:28:47 -0800 Subject: powerpc/5200: dts: Change combatible strings on localbus This patch changes some incorrect compatible strings on the local plus bus node in dts files for MPC5200b based systems. Signed-off-by: John Bonesio Signed-off-by: Grant Likely --- arch/powerpc/boot/dts/cm5200.dts | 2 +- arch/powerpc/boot/dts/digsy_mtc.dts | 2 +- arch/powerpc/boot/dts/media5200.dts | 2 +- arch/powerpc/boot/dts/motionpro.dts | 2 +- 4 files changed, 4 insertions(+), 4 deletions(-) (limited to 'arch/powerpc/boot/dts/cm5200.dts') diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts index d549897b7eb..22f7233414b 100644 --- a/arch/powerpc/boot/dts/cm5200.dts +++ b/arch/powerpc/boot/dts/cm5200.dts @@ -219,7 +219,7 @@ }; localbus { - compatible = "fsl,mpc5200b-lpb","simple-bus"; + compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; #address-cells = <2>; #size-cells = <1>; ranges = <0 0 0xfc000000 0x2000000>; diff --git a/arch/powerpc/boot/dts/digsy_mtc.dts b/arch/powerpc/boot/dts/digsy_mtc.dts index f0592de71bb..3147b989420 100644 --- a/arch/powerpc/boot/dts/digsy_mtc.dts +++ b/arch/powerpc/boot/dts/digsy_mtc.dts @@ -218,7 +218,7 @@ }; localbus { - compatible = "fsl,mpc5200b-lpb","simple-bus"; + compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; #address-cells = <2>; #size-cells = <1>; ranges = <0 0 0xff000000 0x1000000>; diff --git a/arch/powerpc/boot/dts/media5200.dts b/arch/powerpc/boot/dts/media5200.dts index e027f459c23..861f09ff3a7 100644 --- a/arch/powerpc/boot/dts/media5200.dts +++ b/arch/powerpc/boot/dts/media5200.dts @@ -270,7 +270,7 @@ }; localbus { - compatible = "fsl,mpc5200b-lpb","simple-bus"; + compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; #address-cells = <2>; #size-cells = <1>; diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts index 3ab4666c994..97cb08598a4 100644 --- a/arch/powerpc/boot/dts/motionpro.dts +++ b/arch/powerpc/boot/dts/motionpro.dts @@ -236,7 +236,7 @@ }; localbus { - compatible = "fsl,mpc5200b-lpb","simple-bus"; + compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; #address-cells = <2>; #size-cells = <1>; ranges = <0 0 0xff000000 0x01000000 -- cgit v1.2.3-70-g09d2 From c8bf6b52af670496f1e8145600e74a3ef3942a4c Mon Sep 17 00:00:00 2001 From: John Bonesio Date: Wed, 17 Nov 2010 15:28:56 -0800 Subject: powerpc/5200: dts: refactor dts files This patch creates mpc5200b.dtsi containing the information for the MPC5200b SoC then modifies all of the dts files for MPC5200b based systems to use mpc5200b.dtsi. Signed-off-by: John Bonesio Signed-off-by: Grant Likely --- arch/powerpc/boot/dts/cm5200.dts | 192 ++++--------------------- arch/powerpc/boot/dts/digsy_mtc.dts | 173 +++-------------------- arch/powerpc/boot/dts/lite5200b.dts | 217 ++-------------------------- arch/powerpc/boot/dts/media5200.dts | 210 +++------------------------ arch/powerpc/boot/dts/motionpro.dts | 190 ++++--------------------- arch/powerpc/boot/dts/mpc5200b.dtsi | 275 ++++++++++++++++++++++++++++++++++++ arch/powerpc/boot/dts/mucmc52.dts | 174 ++++++----------------- arch/powerpc/boot/dts/pcm030.dts | 187 ++---------------------- arch/powerpc/boot/dts/pcm032.dts | 231 ++++-------------------------- arch/powerpc/boot/dts/uc101.dts | 160 +++++---------------- 10 files changed, 506 insertions(+), 1503 deletions(-) create mode 100644 arch/powerpc/boot/dts/mpc5200b.dtsi (limited to 'arch/powerpc/boot/dts/cm5200.dts') diff --git a/arch/powerpc/boot/dts/cm5200.dts b/arch/powerpc/boot/dts/cm5200.dts index 22f7233414b..ad3a4f4a2b0 100644 --- a/arch/powerpc/boot/dts/cm5200.dts +++ b/arch/powerpc/boot/dts/cm5200.dts @@ -10,226 +10,82 @@ * option) any later version. */ -/dts-v1/; +/include/ "mpc5200b.dtsi" / { model = "schindler,cm5200"; compatible = "schindler,cm5200"; - #address-cells = <1>; - #size-cells = <1>; - interrupt-parent = <&mpc5200_pic>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - PowerPC,5200@0 { - device_type = "cpu"; - reg = <0>; - d-cache-line-size = <32>; - i-cache-line-size = <32>; - d-cache-size = <0x4000>; // L1, 16K - i-cache-size = <0x4000>; // L1, 16K - timebase-frequency = <0>; // from bootloader - bus-frequency = <0>; // from bootloader - clock-frequency = <0>; // from bootloader - }; - }; - - memory { - device_type = "memory"; - reg = <0x00000000 0x04000000>; // 64MB - }; soc5200@f0000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc5200b-immr"; - ranges = <0 0xf0000000 0x0000c000>; - reg = <0xf0000000 0x00000100>; - bus-frequency = <0>; // from bootloader - system-frequency = <0>; // from bootloader - - cdm@200 { - compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm"; - reg = <0x200 0x38>; - }; - - mpc5200_pic: interrupt-controller@500 { - // 5200 interrupts are encoded into two levels; - interrupt-controller; - #interrupt-cells = <3>; - compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic"; - reg = <0x500 0x80>; - }; - timer@600 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x600 0x10>; - interrupts = <1 9 0>; fsl,has-wdt; }; - timer@610 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x610 0x10>; - interrupts = <1 10 0>; - }; - - timer@620 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x620 0x10>; - interrupts = <1 11 0>; - }; - - timer@630 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x630 0x10>; - interrupts = <1 12 0>; - }; - - timer@640 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x640 0x10>; - interrupts = <1 13 0>; - }; - - timer@650 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x650 0x10>; - interrupts = <1 14 0>; - }; - - timer@660 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x660 0x10>; - interrupts = <1 15 0>; - }; - - timer@670 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x670 0x10>; - interrupts = <1 16 0>; - }; - - rtc@800 { // Real time clock - compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc"; - reg = <0x800 0x100>; - interrupts = <1 5 0 1 6 0>; + can@900 { + status = "disabled"; }; - gpio_simple: gpio@b00 { - compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio"; - reg = <0xb00 0x40>; - interrupts = <1 7 0>; - gpio-controller; - #gpio-cells = <2>; - }; - - gpio_wkup: gpio@c00 { - compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup"; - reg = <0xc00 0x40>; - interrupts = <1 8 0 0 3 0>; - gpio-controller; - #gpio-cells = <2>; - }; - - spi@f00 { - compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; - reg = <0xf00 0x20>; - interrupts = <2 13 0 2 14 0>; - }; - - usb@1000 { - compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be"; - reg = <0x1000 0xff>; - interrupts = <2 6 0>; - }; - - dma-controller@1200 { - compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm"; - reg = <0x1200 0x80>; - interrupts = <3 0 0 3 1 0 3 2 0 3 3 0 - 3 4 0 3 5 0 3 6 0 3 7 0 - 3 8 0 3 9 0 3 10 0 3 11 0 - 3 12 0 3 13 0 3 14 0 3 15 0>; - }; - - xlb@1f00 { - compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb"; - reg = <0x1f00 0x100>; + can@980 { + status = "disabled"; }; psc@2000 { // PSC1 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2000 0x100>; - interrupts = <2 1 0>; }; psc@2200 { // PSC2 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2200 0x100>; - interrupts = <2 2 0>; }; psc@2400 { // PSC3 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2400 0x100>; - interrupts = <2 3 0>; + }; + + psc@2600 { // PSC4 + status = "disabled"; + }; + + psc@2800 { // PSC5 + status = "disabled"; }; psc@2c00 { // PSC6 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2c00 0x100>; - interrupts = <2 4 0>; }; ethernet@3000 { - compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec"; - reg = <0x3000 0x400>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <2 5 0>; phy-handle = <&phy0>; }; mdio@3000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio"; - reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts - interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co. - phy0: ethernet-phy@0 { reg = <0>; }; }; - i2c@3d40 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d40 0x40>; - interrupts = <2 16 0>; + ata@3a00 { + status = "disabled"; }; - sram@8000 { - compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram"; - reg = <0x8000 0x4000>; + i2c@3d00 { + status = "disabled"; }; + }; - localbus { - compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0xfc000000 0x2000000>; + pci@f0000d00 { + status = "disabled"; + }; + localbus { // 16-bit flash device at LocalPlus Bus CS0 flash@0,0 { compatible = "cfi-flash"; reg = <0 0 0x2000000>; bank-width = <2>; device-width = <2>; + #size-cells = <1>; + #address-cells = <1>; }; }; }; diff --git a/arch/powerpc/boot/dts/digsy_mtc.dts b/arch/powerpc/boot/dts/digsy_mtc.dts index 3147b989420..27bd267d631 100644 --- a/arch/powerpc/boot/dts/digsy_mtc.dts +++ b/arch/powerpc/boot/dts/digsy_mtc.dts @@ -11,195 +11,68 @@ * option) any later version. */ -/dts-v1/; +/include/ "mpc5200b.dtsi" / { model = "intercontrol,digsy-mtc"; compatible = "intercontrol,digsy-mtc"; - #address-cells = <1>; - #size-cells = <1>; - interrupt-parent = <&mpc5200_pic>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - PowerPC,5200@0 { - device_type = "cpu"; - reg = <0>; - d-cache-line-size = <32>; - i-cache-line-size = <32>; - d-cache-size = <0x4000>; // L1, 16K - i-cache-size = <0x4000>; // L1, 16K - timebase-frequency = <0>; // from bootloader - bus-frequency = <0>; // from bootloader - clock-frequency = <0>; // from bootloader - }; - }; memory { - device_type = "memory"; reg = <0x00000000 0x02000000>; // 32MB }; soc5200@f0000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc5200b-immr"; - ranges = <0 0xf0000000 0x0000c000>; - reg = <0xf0000000 0x00000100>; - bus-frequency = <0>; // from bootloader - system-frequency = <0>; // from bootloader - - cdm@200 { - compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm"; - reg = <0x200 0x38>; - }; - - mpc5200_pic: interrupt-controller@500 { - // 5200 interrupts are encoded into two levels; - interrupt-controller; - #interrupt-cells = <3>; - compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic"; - reg = <0x500 0x80>; - }; - timer@600 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x600 0x10>; - interrupts = <1 9 0>; fsl,has-wdt; }; - timer@610 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x610 0x10>; - interrupts = <1 10 0>; - }; - - timer@620 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x620 0x10>; - interrupts = <1 11 0>; - }; - - timer@630 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x630 0x10>; - interrupts = <1 12 0>; - }; - - timer@640 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x640 0x10>; - interrupts = <1 13 0>; - }; - - timer@650 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x650 0x10>; - interrupts = <1 14 0>; - }; - - timer@660 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x660 0x10>; - interrupts = <1 15 0>; - }; - - timer@670 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x670 0x10>; - interrupts = <1 16 0>; - }; - - gpio_simple: gpio@b00 { - compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio"; - reg = <0xb00 0x40>; - interrupts = <1 7 0>; - gpio-controller; - #gpio-cells = <2>; + rtc@800 { + status = "disabled"; }; - gpio_wkup: gpio@c00 { - compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup"; - reg = <0xc00 0x40>; - interrupts = <1 8 0 0 3 0>; - gpio-controller; - #gpio-cells = <2>; + can@900 { + status = "disabled"; }; - spi@f00 { - compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; - reg = <0xf00 0x20>; - interrupts = <2 13 0 2 14 0>; + can@980 { + status = "disabled"; }; - usb@1000 { - compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be"; - reg = <0x1000 0xff>; - interrupts = <2 6 0>; + psc@2000 { // PSC1 + status = "disabled"; }; - dma-controller@1200 { - compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm"; - reg = <0x1200 0x80>; - interrupts = <3 0 0 3 1 0 3 2 0 3 3 0 - 3 4 0 3 5 0 3 6 0 3 7 0 - 3 8 0 3 9 0 3 10 0 3 11 0 - 3 12 0 3 13 0 3 14 0 3 15 0>; + psc@2200 { // PSC2 + status = "disabled"; }; - xlb@1f00 { - compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb"; - reg = <0x1f00 0x100>; + psc@2400 { // PSC3 + status = "disabled"; }; psc@2600 { // PSC4 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2600 0x100>; - interrupts = <2 11 0>; }; psc@2800 { // PSC5 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2800 0x100>; - interrupts = <2 12 0>; + }; + + psc@2c00 { // PSC6 + status = "disabled"; }; ethernet@3000 { - compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec"; - reg = <0x3000 0x400>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <2 5 0>; phy-handle = <&phy0>; }; mdio@3000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio"; - reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts - interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co. - phy0: ethernet-phy@0 { reg = <0>; }; }; - ata@3a00 { - compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata"; - reg = <0x3a00 0x100>; - interrupts = <2 7 0>; - }; - i2c@3d00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d00 0x40>; - interrupts = <2 15 0>; - rtc@50 { compatible = "at,24c08"; reg = <0x50>; @@ -211,16 +84,16 @@ }; }; - sram@8000 { - compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram"; - reg = <0x8000 0x4000>; + i2c@3d40 { + status = "disabled"; }; }; + pci@f0000d00 { + status = "disabled"; + }; + localbus { - compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; - #address-cells = <2>; - #size-cells = <1>; ranges = <0 0 0xff000000 0x1000000>; // 16-bit flash device at LocalPlus Bus CS0 diff --git a/arch/powerpc/boot/dts/lite5200b.dts b/arch/powerpc/boot/dts/lite5200b.dts index c0a4e4592ba..fb288bb882b 100644 --- a/arch/powerpc/boot/dts/lite5200b.dts +++ b/arch/powerpc/boot/dts/lite5200b.dts @@ -10,253 +10,75 @@ * option) any later version. */ -/dts-v1/; +/include/ "mpc5200b.dtsi" / { model = "fsl,lite5200b"; compatible = "fsl,lite5200b"; - #address-cells = <1>; - #size-cells = <1>; - interrupt-parent = <&mpc5200_pic>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - PowerPC,5200@0 { - device_type = "cpu"; - reg = <0>; - d-cache-line-size = <32>; - i-cache-line-size = <32>; - d-cache-size = <0x4000>; // L1, 16K - i-cache-size = <0x4000>; // L1, 16K - timebase-frequency = <0>; // from bootloader - bus-frequency = <0>; // from bootloader - clock-frequency = <0>; // from bootloader - }; - }; memory { - device_type = "memory"; reg = <0x00000000 0x10000000>; // 256MB }; soc5200@f0000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc5200b-immr"; - ranges = <0 0xf0000000 0x0000c000>; - reg = <0xf0000000 0x00000100>; - bus-frequency = <0>; // from bootloader - system-frequency = <0>; // from bootloader - - cdm@200 { - compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm"; - reg = <0x200 0x38>; - }; - - mpc5200_pic: interrupt-controller@500 { - // 5200 interrupts are encoded into two levels; - interrupt-controller; - #interrupt-cells = <3>; - compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic"; - reg = <0x500 0x80>; - }; - timer@600 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x600 0x10>; - interrupts = <1 9 0>; fsl,has-wdt; }; - timer@610 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x610 0x10>; - interrupts = <1 10 0>; - }; - - timer@620 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x620 0x10>; - interrupts = <1 11 0>; - }; - - timer@630 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x630 0x10>; - interrupts = <1 12 0>; - }; - - timer@640 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x640 0x10>; - interrupts = <1 13 0>; - }; - - timer@650 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x650 0x10>; - interrupts = <1 14 0>; - }; - - timer@660 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x660 0x10>; - interrupts = <1 15 0>; - }; - - timer@670 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x670 0x10>; - interrupts = <1 16 0>; - }; - - rtc@800 { // Real time clock - compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc"; - reg = <0x800 0x100>; - interrupts = <1 5 0 1 6 0>; - }; - - can@900 { - compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; - interrupts = <2 17 0>; - reg = <0x900 0x80>; - }; - - can@980 { - compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; - interrupts = <2 18 0>; - reg = <0x980 0x80>; - }; - - gpio_simple: gpio@b00 { - compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio"; - reg = <0xb00 0x40>; - interrupts = <1 7 0>; - gpio-controller; - #gpio-cells = <2>; - }; - - gpio_wkup: gpio@c00 { - compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup"; - reg = <0xc00 0x40>; - interrupts = <1 8 0 0 3 0>; - gpio-controller; - #gpio-cells = <2>; + psc@2000 { // PSC1 + compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; + cell-index = <0>; }; - spi@f00 { - compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; - reg = <0xf00 0x20>; - interrupts = <2 13 0 2 14 0>; + psc@2200 { // PSC2 + status = "disabled"; }; - usb@1000 { - compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be"; - reg = <0x1000 0xff>; - interrupts = <2 6 0>; + psc@2400 { // PSC3 + status = "disabled"; }; - dma-controller@1200 { - compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm"; - reg = <0x1200 0x80>; - interrupts = <3 0 0 3 1 0 3 2 0 3 3 0 - 3 4 0 3 5 0 3 6 0 3 7 0 - 3 8 0 3 9 0 3 10 0 3 11 0 - 3 12 0 3 13 0 3 14 0 3 15 0>; + psc@2600 { // PSC4 + status = "disabled"; }; - xlb@1f00 { - compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb"; - reg = <0x1f00 0x100>; + psc@2800 { // PSC5 + status = "disabled"; }; - psc@2000 { // PSC1 - compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2000 0x100>; - interrupts = <2 1 0>; + psc@2c00 { // PSC6 + status = "disabled"; }; // PSC2 in ac97 mode example //ac97@2200 { // PSC2 // compatible = "fsl,mpc5200b-psc-ac97","fsl,mpc5200-psc-ac97"; // cell-index = <1>; - // reg = <0x2200 0x100>; - // interrupts = <2 2 0>; //}; // PSC3 in CODEC mode example //i2s@2400 { // PSC3 // compatible = "fsl,mpc5200b-psc-i2s"; //not 5200 compatible // cell-index = <2>; - // reg = <0x2400 0x100>; - // interrupts = <2 3 0>; - //}; - - // PSC4 in uart mode example - //serial@2600 { // PSC4 - // compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - // reg = <0x2600 0x100>; - // interrupts = <2 11 0>; - //}; - - // PSC5 in uart mode example - //serial@2800 { // PSC5 - // compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - // reg = <0x2800 0x100>; - // interrupts = <2 12 0>; //}; // PSC6 in spi mode example //spi@2c00 { // PSC6 // compatible = "fsl,mpc5200b-psc-spi","fsl,mpc5200-psc-spi"; // cell-index = <5>; - // reg = <0x2c00 0x100>; - // interrupts = <2 4 0>; //}; ethernet@3000 { - compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec"; - reg = <0x3000 0x400>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <2 5 0>; phy-handle = <&phy0>; }; mdio@3000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio"; - reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts - interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co. - phy0: ethernet-phy@0 { reg = <0>; }; }; - ata@3a00 { - compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata"; - reg = <0x3a00 0x100>; - interrupts = <2 7 0>; - }; - - i2c@3d00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d00 0x40>; - interrupts = <2 15 0>; - }; - i2c@3d40 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d40 0x40>; - interrupts = <2 16 0>; - eeprom@50 { compatible = "atmel,24c02"; reg = <0x50>; @@ -270,12 +92,6 @@ }; pci@f0000d00 { - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - device_type = "pci"; - compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci"; - reg = <0xf0000d00 0x100>; interrupt-map-mask = <0xf800 0 0 7>; interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot 0xc000 0 0 2 &mpc5200_pic 1 1 3 @@ -295,11 +111,6 @@ }; localbus { - compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; - - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0xfe000000 0x02000000>; flash@0,0 { diff --git a/arch/powerpc/boot/dts/media5200.dts b/arch/powerpc/boot/dts/media5200.dts index 861f09ff3a7..48d72f38e5e 100644 --- a/arch/powerpc/boot/dts/media5200.dts +++ b/arch/powerpc/boot/dts/media5200.dts @@ -11,14 +11,11 @@ * option) any later version. */ -/dts-v1/; +/include/ "mpc5200b.dtsi" / { model = "fsl,media5200"; compatible = "fsl,media5200"; - #address-cells = <1>; - #size-cells = <1>; - interrupt-parent = <&mpc5200_pic>; aliases { console = &console; @@ -30,16 +27,7 @@ }; cpus { - #address-cells = <1>; - #size-cells = <0>; - PowerPC,5200@0 { - device_type = "cpu"; - reg = <0>; - d-cache-line-size = <32>; - i-cache-line-size = <32>; - d-cache-size = <0x4000>; // L1, 16K - i-cache-size = <0x4000>; // L1, 16K timebase-frequency = <33000000>; // 33 MHz, these were configured by U-Boot bus-frequency = <132000000>; // 132 MHz clock-frequency = <396000000>; // 396 MHz @@ -47,203 +35,57 @@ }; memory { - device_type = "memory"; reg = <0x00000000 0x08000000>; // 128MB RAM }; - soc@f0000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc5200b-immr"; - ranges = <0 0xf0000000 0x0000c000>; - reg = <0xf0000000 0x00000100>; + soc5200@f0000000 { bus-frequency = <132000000>;// 132 MHz - system-frequency = <0>; // from bootloader - - cdm@200 { - compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm"; - reg = <0x200 0x38>; - }; - - mpc5200_pic: interrupt-controller@500 { - // 5200 interrupts are encoded into two levels; - interrupt-controller; - #interrupt-cells = <3>; - compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic"; - reg = <0x500 0x80>; - }; timer@600 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x600 0x10>; - interrupts = <1 9 0>; fsl,has-wdt; }; - timer@610 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x610 0x10>; - interrupts = <1 10 0>; - }; - - timer@620 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x620 0x10>; - interrupts = <1 11 0>; - }; - - timer@630 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x630 0x10>; - interrupts = <1 12 0>; - }; - - timer@640 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x640 0x10>; - interrupts = <1 13 0>; - }; - - timer@650 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x650 0x10>; - interrupts = <1 14 0>; - }; - - timer@660 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x660 0x10>; - interrupts = <1 15 0>; - }; - - timer@670 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x670 0x10>; - interrupts = <1 16 0>; - }; - - rtc@800 { // Real time clock - compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc"; - reg = <0x800 0x100>; - interrupts = <1 5 0 1 6 0>; - }; - - can@900 { - compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; - interrupts = <2 17 0>; - reg = <0x900 0x80>; + psc@2000 { // PSC1 + status = "disabled"; }; - can@980 { - compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; - interrupts = <2 18 0>; - reg = <0x980 0x80>; + psc@2200 { // PSC2 + status = "disabled"; }; - gpio_simple: gpio@b00 { - compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio"; - reg = <0xb00 0x40>; - interrupts = <1 7 0>; - gpio-controller; - #gpio-cells = <2>; + psc@2400 { // PSC3 + status = "disabled"; }; - gpio_wkup: gpio@c00 { - compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup"; - reg = <0xc00 0x40>; - interrupts = <1 8 0 0 3 0>; - gpio-controller; - #gpio-cells = <2>; + psc@2600 { // PSC4 + status = "disabled"; }; - spi@f00 { - compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; - reg = <0xf00 0x20>; - interrupts = <2 13 0 2 14 0>; - }; - - usb@1000 { - compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be"; - reg = <0x1000 0x100>; - interrupts = <2 6 0>; - }; - - dma-controller@1200 { - compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm"; - reg = <0x1200 0x80>; - interrupts = <3 0 0 3 1 0 3 2 0 3 3 0 - 3 4 0 3 5 0 3 6 0 3 7 0 - 3 8 0 3 9 0 3 10 0 3 11 0 - 3 12 0 3 13 0 3 14 0 3 15 0>; - }; - - xlb@1f00 { - compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb"; - reg = <0x1f00 0x100>; + psc@2800 { // PSC5 + status = "disabled"; }; // PSC6 in uart mode console: psc@2c00 { // PSC6 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2c00 0x100>; - interrupts = <2 4 0>; }; - eth0: ethernet@3000 { - compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec"; - reg = <0x3000 0x400>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <2 5 0>; + ethernet@3000 { phy-handle = <&phy0>; }; mdio@3000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio"; - reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts - interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co. - phy0: ethernet-phy@0 { reg = <0>; }; }; - ata@3a00 { - compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata"; - reg = <0x3a00 0x100>; - interrupts = <2 7 0>; - }; - - i2c@3d00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d00 0x40>; - interrupts = <2 15 0>; - }; - - i2c@3d40 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d40 0x40>; - interrupts = <2 16 0>; - }; - - sram@8000 { - compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram"; - reg = <0x8000 0x4000>; + usb@1000 { + reg = <0x1000 0x100>; }; }; pci@f0000d00 { - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - device_type = "pci"; - compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci"; - reg = <0xf0000d00 0x100>; interrupt-map-mask = <0xf800 0 0 7>; interrupt-map = <0xc000 0 0 1 &media5200_fpga 0 2 // 1st slot 0xc000 0 0 2 &media5200_fpga 0 3 @@ -260,37 +102,29 @@ 0xe000 0 0 1 &media5200_fpga 0 5 // CoralIP >; - clock-frequency = <0>; // From boot loader - interrupts = <2 8 0 2 9 0 2 10 0>; - interrupt-parent = <&mpc5200_pic>; - bus-range = <0 0>; ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000 0x02000000 0 0xa0000000 0xa0000000 0 0x10000000 0x01000000 0 0x00000000 0xb0000000 0 0x01000000>; + interrupt-parent = <&mpc5200_pic>; }; localbus { - compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; - #address-cells = <2>; - #size-cells = <1>; - ranges = < 0 0 0xfc000000 0x02000000 1 0 0xfe000000 0x02000000 2 0 0xf0010000 0x00010000 3 0 0xf0020000 0x00010000 >; - flash@0,0 { compatible = "amd,am29lv28ml", "cfi-flash"; - reg = <0 0x0 0x2000000>; // 32 MB - bank-width = <4>; // Width in bytes of the flash bank - device-width = <2>; // Two devices on each bank + reg = <0 0x0 0x2000000>; // 32 MB + bank-width = <4>; // Width in bytes of the flash bank + device-width = <2>; // Two devices on each bank }; flash@1,0 { compatible = "amd,am29lv28ml", "cfi-flash"; - reg = <1 0 0x2000000>; // 32 MB - bank-width = <4>; // Width in bytes of the flash bank - device-width = <2>; // Two devices on each bank + reg = <1 0 0x2000000>; // 32 MB + bank-width = <4>; // Width in bytes of the flash bank + device-width = <2>; // Two devices on each bank }; media5200_fpga: fpga@2,0 { diff --git a/arch/powerpc/boot/dts/motionpro.dts b/arch/powerpc/boot/dts/motionpro.dts index 97cb08598a4..0b78e89ac69 100644 --- a/arch/powerpc/boot/dts/motionpro.dts +++ b/arch/powerpc/boot/dts/motionpro.dts @@ -10,219 +10,73 @@ * option) any later version. */ -/dts-v1/; +/include/ "mpc5200b.dtsi" / { model = "promess,motionpro"; compatible = "promess,motionpro"; - #address-cells = <1>; - #size-cells = <1>; - interrupt-parent = <&mpc5200_pic>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - PowerPC,5200@0 { - device_type = "cpu"; - reg = <0>; - d-cache-line-size = <32>; - i-cache-line-size = <32>; - d-cache-size = <0x4000>; // L1, 16K - i-cache-size = <0x4000>; // L1, 16K - timebase-frequency = <0>; // from bootloader - bus-frequency = <0>; // from bootloader - clock-frequency = <0>; // from bootloader - }; - }; - - memory { - device_type = "memory"; - reg = <0x00000000 0x04000000>; // 64MB - }; soc5200@f0000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc5200b-immr"; - ranges = <0 0xf0000000 0x0000c000>; - reg = <0xf0000000 0x00000100>; - bus-frequency = <0>; // from bootloader - system-frequency = <0>; // from bootloader - - cdm@200 { - compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm"; - reg = <0x200 0x38>; - }; - - mpc5200_pic: interrupt-controller@500 { - // 5200 interrupts are encoded into two levels; - interrupt-controller; - #interrupt-cells = <3>; - compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic"; - reg = <0x500 0x80>; - }; - timer@600 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x600 0x10>; - interrupts = <1 9 0>; fsl,has-wdt; }; - timer@610 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x610 0x10>; - interrupts = <1 10 0>; - }; - - timer@620 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x620 0x10>; - interrupts = <1 11 0>; - }; - - timer@630 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x630 0x10>; - interrupts = <1 12 0>; - }; - - timer@640 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x640 0x10>; - interrupts = <1 13 0>; - }; - - timer@650 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x650 0x10>; - interrupts = <1 14 0>; - }; - timer@660 { // Motion-PRO status LED compatible = "promess,motionpro-led"; label = "motionpro-statusled"; - reg = <0x660 0x10>; - interrupts = <1 15 0>; blink-delay = <100>; // 100 msec }; timer@670 { // Motion-PRO ready LED compatible = "promess,motionpro-led"; label = "motionpro-readyled"; - reg = <0x670 0x10>; - interrupts = <1 16 0>; - }; - - rtc@800 { // Real time clock - compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc"; - reg = <0x800 0x100>; - interrupts = <1 5 0 1 6 0>; - }; - - can@980 { - compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; - interrupts = <2 18 0>; - reg = <0x980 0x80>; }; - gpio_simple: gpio@b00 { - compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio"; - reg = <0xb00 0x40>; - interrupts = <1 7 0>; - gpio-controller; - #gpio-cells = <2>; - }; - - gpio_wkup: gpio@c00 { - compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup"; - reg = <0xc00 0x40>; - interrupts = <1 8 0 0 3 0>; - gpio-controller; - #gpio-cells = <2>; - }; - - spi@f00 { - compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; - reg = <0xf00 0x20>; - interrupts = <2 13 0 2 14 0>; - }; - - usb@1000 { - compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be"; - reg = <0x1000 0xff>; - interrupts = <2 6 0>; - }; - - dma-controller@1200 { - compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm"; - reg = <0x1200 0x80>; - interrupts = <3 0 0 3 1 0 3 2 0 3 3 0 - 3 4 0 3 5 0 3 6 0 3 7 0 - 3 8 0 3 9 0 3 10 0 3 11 0 - 3 12 0 3 13 0 3 14 0 3 15 0>; - }; - - xlb@1f00 { - compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb"; - reg = <0x1f00 0x100>; + can@900 { + status = "disabled"; }; psc@2000 { // PSC1 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2000 0x100>; - interrupts = <2 1 0>; }; // PSC2 in spi master mode psc@2200 { // PSC2 compatible = "fsl,mpc5200b-psc-spi","fsl,mpc5200-psc-spi"; cell-index = <1>; - reg = <0x2200 0x100>; - interrupts = <2 2 0>; }; - // PSC5 in uart mode + psc@2400 { // PSC3 + status = "disabled"; + }; + + psc@2600 { // PSC4 + status = "disabled"; + }; + psc@2800 { // PSC5 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2800 0x100>; - interrupts = <2 12 0>; + }; + + psc@2c00 { // PSC6 + status = "disabled"; }; ethernet@3000 { - compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec"; - reg = <0x3000 0x400>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <2 5 0>; phy-handle = <&phy0>; }; mdio@3000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio"; - reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts - interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co. - phy0: ethernet-phy@2 { reg = <2>; }; }; - ata@3a00 { - compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata"; - reg = <0x3a00 0x100>; - interrupts = <2 7 0>; + i2c@3d00 { + status = "disabled"; }; i2c@3d40 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d40 0x40>; - interrupts = <2 16 0>; - rtc@68 { compatible = "dallas,ds1339"; reg = <0x68>; @@ -235,10 +89,11 @@ }; }; + pci@f0000d00 { + status = "disabled"; + }; + localbus { - compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; - #address-cells = <2>; - #size-cells = <1>; ranges = <0 0 0xff000000 0x01000000 1 0 0x50000000 0x00010000 2 0 0x50010000 0x00010000 @@ -277,6 +132,9 @@ reg = <0 0 0x01000000>; bank-width = <2>; device-width = <2>; + #size-cells = <1>; + #address-cells = <1>; }; + }; }; diff --git a/arch/powerpc/boot/dts/mpc5200b.dtsi b/arch/powerpc/boot/dts/mpc5200b.dtsi new file mode 100644 index 00000000000..bc27548e895 --- /dev/null +++ b/arch/powerpc/boot/dts/mpc5200b.dtsi @@ -0,0 +1,275 @@ +/* + * base MPC5200b Device Tree Source + * + * Copyright (C) 2010 SecretLab + * Grant Likely + * John Bonesio + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/dts-v1/; + +/ { + model = "fsl,mpc5200b"; + compatible = "fsl,mpc5200b"; + #address-cells = <1>; + #size-cells = <1>; + interrupt-parent = <&mpc5200_pic>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + powerpc: PowerPC,5200@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <32>; + i-cache-line-size = <32>; + d-cache-size = <0x4000>; // L1, 16K + i-cache-size = <0x4000>; // L1, 16K + timebase-frequency = <0>; // from bootloader + bus-frequency = <0>; // from bootloader + clock-frequency = <0>; // from bootloader + }; + }; + + memory: memory { + device_type = "memory"; + reg = <0x00000000 0x04000000>; // 64MB + }; + + soc: soc5200@f0000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc5200b-immr"; + ranges = <0 0xf0000000 0x0000c000>; + reg = <0xf0000000 0x00000100>; + bus-frequency = <0>; // from bootloader + system-frequency = <0>; // from bootloader + + cdm@200 { + compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm"; + reg = <0x200 0x38>; + }; + + mpc5200_pic: interrupt-controller@500 { + // 5200 interrupts are encoded into two levels; + interrupt-controller; + #interrupt-cells = <3>; + compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic"; + reg = <0x500 0x80>; + }; + + timer@600 { // General Purpose Timer + compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; + reg = <0x600 0x10>; + interrupts = <1 9 0>; + }; + + timer@610 { // General Purpose Timer + compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; + reg = <0x610 0x10>; + interrupts = <1 10 0>; + }; + + timer@620 { // General Purpose Timer + compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; + reg = <0x620 0x10>; + interrupts = <1 11 0>; + }; + + timer@630 { // General Purpose Timer + compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; + reg = <0x630 0x10>; + interrupts = <1 12 0>; + }; + + timer@640 { // General Purpose Timer + compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; + reg = <0x640 0x10>; + interrupts = <1 13 0>; + }; + + timer@650 { // General Purpose Timer + compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; + reg = <0x650 0x10>; + interrupts = <1 14 0>; + }; + + timer@660 { // General Purpose Timer + compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; + reg = <0x660 0x10>; + interrupts = <1 15 0>; + }; + + timer@670 { // General Purpose Timer + compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; + reg = <0x670 0x10>; + interrupts = <1 16 0>; + }; + + rtc@800 { // Real time clock + compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc"; + reg = <0x800 0x100>; + interrupts = <1 5 0 1 6 0>; + }; + + can@900 { + compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; + interrupts = <2 17 0>; + reg = <0x900 0x80>; + }; + + can@980 { + compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; + interrupts = <2 18 0>; + reg = <0x980 0x80>; + }; + + gpio_simple: gpio@b00 { + compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio"; + reg = <0xb00 0x40>; + interrupts = <1 7 0>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio_wkup: gpio@c00 { + compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup"; + reg = <0xc00 0x40>; + interrupts = <1 8 0 0 3 0>; + gpio-controller; + #gpio-cells = <2>; + }; + + spi@f00 { + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; + reg = <0xf00 0x20>; + interrupts = <2 13 0 2 14 0>; + }; + + usb: usb@1000 { + compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be"; + reg = <0x1000 0xff>; + interrupts = <2 6 0>; + }; + + dma-controller@1200 { + compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm"; + reg = <0x1200 0x80>; + interrupts = <3 0 0 3 1 0 3 2 0 3 3 0 + 3 4 0 3 5 0 3 6 0 3 7 0 + 3 8 0 3 9 0 3 10 0 3 11 0 + 3 12 0 3 13 0 3 14 0 3 15 0>; + }; + + xlb@1f00 { + compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb"; + reg = <0x1f00 0x100>; + }; + + psc1: psc@2000 { // PSC1 + compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc"; + reg = <0x2000 0x100>; + interrupts = <2 1 0>; + }; + + psc2: psc@2200 { // PSC2 + compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc"; + reg = <0x2200 0x100>; + interrupts = <2 2 0>; + }; + + psc3: psc@2400 { // PSC3 + compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc"; + reg = <0x2400 0x100>; + interrupts = <2 3 0>; + }; + + psc4: psc@2600 { // PSC4 + compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc"; + reg = <0x2600 0x100>; + interrupts = <2 11 0>; + }; + + psc5: psc@2800 { // PSC5 + compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc"; + reg = <0x2800 0x100>; + interrupts = <2 12 0>; + }; + + psc6: psc@2c00 { // PSC6 + compatible = "fsl,mpc5200b-psc","fsl,mpc5200-psc"; + reg = <0x2c00 0x100>; + interrupts = <2 4 0>; + }; + + eth0: ethernet@3000 { + compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec"; + reg = <0x3000 0x400>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <2 5 0>; + }; + + mdio@3000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio"; + reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts + interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co. + }; + + ata@3a00 { + compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata"; + reg = <0x3a00 0x100>; + interrupts = <2 7 0>; + }; + + i2c@3d00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; + reg = <0x3d00 0x40>; + interrupts = <2 15 0>; + }; + + i2c@3d40 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; + reg = <0x3d40 0x40>; + interrupts = <2 16 0>; + }; + + sram@8000 { + compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram"; + reg = <0x8000 0x4000>; + }; + }; + + pci: pci@f0000d00 { + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci"; + reg = <0xf0000d00 0x100>; + // interrupt-map-mask = need to add + // interrupt-map = need to add + clock-frequency = <0>; // From boot loader + interrupts = <2 8 0 2 9 0 2 10 0>; + bus-range = <0 0>; + // ranges = need to add + }; + + localbus: localbus { + compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0xfc000000 0x2000000>; + }; +}; diff --git a/arch/powerpc/boot/dts/mucmc52.dts b/arch/powerpc/boot/dts/mucmc52.dts index 8dc212d9238..21d34720fcc 100644 --- a/arch/powerpc/boot/dts/mucmc52.dts +++ b/arch/powerpc/boot/dts/mucmc52.dts @@ -11,172 +11,109 @@ * option) any later version. */ -/dts-v1/; +/include/ "mpc5200b.dtsi" / { model = "manroland,mucmc52"; compatible = "manroland,mucmc52"; - #address-cells = <1>; - #size-cells = <1>; - interrupt-parent = <&mpc5200_pic>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - PowerPC,5200@0 { - device_type = "cpu"; - reg = <0>; - d-cache-line-size = <32>; - i-cache-line-size = <32>; - d-cache-size = <0x4000>; // L1, 16K - i-cache-size = <0x4000>; // L1, 16K - timebase-frequency = <0>; // from bootloader - bus-frequency = <0>; // from bootloader - clock-frequency = <0>; // from bootloader - }; - }; - - memory { - device_type = "memory"; - reg = <0x00000000 0x04000000>; // 64MB - }; soc5200@f0000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc5200b-immr"; - ranges = <0 0xf0000000 0x0000c000>; - reg = <0xf0000000 0x00000100>; - bus-frequency = <0>; // from bootloader - system-frequency = <0>; // from bootloader - - cdm@200 { - compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm"; - reg = <0x200 0x38>; - }; - - mpc5200_pic: interrupt-controller@500 { - // 5200 interrupts are encoded into two levels; - interrupt-controller; - #interrupt-cells = <3>; - compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic"; - reg = <0x500 0x80>; - }; - gpt0: timer@600 { // GPT 0 in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x600 0x10>; - interrupts = <1 9 0>; gpio-controller; #gpio-cells = <2>; }; gpt1: timer@610 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x610 0x10>; - interrupts = <1 10 0>; gpio-controller; #gpio-cells = <2>; }; gpt2: timer@620 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x620 0x10>; - interrupts = <1 11 0>; gpio-controller; #gpio-cells = <2>; }; gpt3: timer@630 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x630 0x10>; - interrupts = <1 12 0>; gpio-controller; #gpio-cells = <2>; }; - gpio_simple: gpio@b00 { - compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio"; - reg = <0xb00 0x40>; - interrupts = <1 7 0>; - gpio-controller; - #gpio-cells = <2>; + timer@640 { + status = "disabled"; }; - gpio_wkup: gpio@c00 { - compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup"; - reg = <0xc00 0x40>; - interrupts = <1 8 0 0 3 0>; - gpio-controller; - #gpio-cells = <2>; + timer@650 { + status = "disabled"; + }; + + timer@660 { + status = "disabled"; + }; + + timer@670 { + status = "disabled"; }; - dma-controller@1200 { - compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm"; - reg = <0x1200 0x80>; - interrupts = <3 0 0 3 1 0 3 2 0 3 3 0 - 3 4 0 3 5 0 3 6 0 3 7 0 - 3 8 0 3 9 0 3 10 0 3 11 0 - 3 12 0 3 13 0 3 14 0 3 15 0>; + rtc@800 { + status = "disabled"; }; - xlb@1f00 { - compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb"; - reg = <0x1f00 0x100>; + can@900 { + status = "disabled"; }; - psc@2000 { /* PSC1 in UART mode */ + can@980 { + status = "disabled"; + }; + + spi@f00 { + status = "disabled"; + }; + + usb@1000 { + status = "disabled"; + }; + + psc@2000 { // PSC1 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2000 0x100>; - interrupts = <2 1 0>; }; - psc@2200 { /* PSC2 in UART mode */ + psc@2200 { // PSC2 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2200 0x100>; - interrupts = <2 2 0>; }; - psc@2c00 { /* PSC6 in UART mode */ + psc@2400 { // PSC3 + status = "disabled"; + }; + + psc@2600 { // PSC4 + status = "disabled"; + }; + + psc@2800 { // PSC5 + status = "disabled"; + }; + + psc@2c00 { // PSC6 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2c00 0x100>; - interrupts = <2 4 0>; }; ethernet@3000 { - compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec"; - reg = <0x3000 0x400>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <2 5 0>; phy-handle = <&phy0>; }; mdio@3000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio"; - reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts - interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co. - phy0: ethernet-phy@0 { compatible = "intel,lxt971"; reg = <0>; }; }; - ata@3a00 { - compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata"; - reg = <0x3a00 0x100>; - interrupts = <2 7 0>; + i2c@3d00 { + status = "disabled"; }; i2c@3d40 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d40 0x40>; - interrupts = <2 16 0>; hwmon@2c { compatible = "ad,adm9240"; reg = <0x2c>; @@ -186,20 +123,9 @@ reg = <0x51>; }; }; - - sram@8000 { - compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram"; - reg = <0x8000 0x4000>; - }; }; pci@f0000d00 { - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - device_type = "pci"; - compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci"; - reg = <0xf0000d00 0x100>; interrupt-map-mask = <0xf800 0 0 7>; interrupt-map = < /* IDSEL 0x10 */ @@ -208,20 +134,12 @@ 0x8000 0 0 3 &mpc5200_pic 0 2 3 0x8000 0 0 4 &mpc5200_pic 0 1 3 >; - clock-frequency = <0>; // From boot loader - interrupts = <2 8 0 2 9 0 2 10 0>; - bus-range = <0 0>; ranges = <0x42000000 0 0x60000000 0x60000000 0 0x10000000 0x02000000 0 0x90000000 0x90000000 0 0x10000000 0x01000000 0 0x00000000 0xa0000000 0 0x01000000>; }; localbus { - compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; - - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0xff800000 0x00800000 1 0 0x80000000 0x00800000 3 0 0x80000000 0x00800000>; diff --git a/arch/powerpc/boot/dts/pcm030.dts b/arch/powerpc/boot/dts/pcm030.dts index 28d77758d8b..9e354997eb7 100644 --- a/arch/powerpc/boot/dts/pcm030.dts +++ b/arch/powerpc/boot/dts/pcm030.dts @@ -12,244 +12,92 @@ * option) any later version. */ -/dts-v1/; +/include/ "mpc5200b.dtsi" / { model = "phytec,pcm030"; compatible = "phytec,pcm030"; - #address-cells = <1>; - #size-cells = <1>; - interrupt-parent = <&mpc5200_pic>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - PowerPC,5200@0 { - device_type = "cpu"; - reg = <0>; - d-cache-line-size = <32>; - i-cache-line-size = <32>; - d-cache-size = <0x4000>; // L1, 16K - i-cache-size = <0x4000>; // L1, 16K - timebase-frequency = <0>; // from bootloader - bus-frequency = <0>; // from bootloader - clock-frequency = <0>; // from bootloader - }; - }; - - memory { - device_type = "memory"; - reg = <0x00000000 0x04000000>; // 64MB - }; soc5200@f0000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc5200b-immr"; - ranges = <0 0xf0000000 0x0000c000>; - bus-frequency = <0>; // from bootloader - system-frequency = <0>; // from bootloader - - cdm@200 { - compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm"; - reg = <0x200 0x38>; - }; - - mpc5200_pic: interrupt-controller@500 { - // 5200 interrupts are encoded into two levels; - interrupt-controller; - #interrupt-cells = <3>; - compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic"; - reg = <0x500 0x80>; - }; - - timer@600 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x600 0x10>; - interrupts = <1 9 0>; + timer@600 { // General Purpose Timer fsl,has-wdt; }; - timer@610 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x610 0x10>; - interrupts = <1 10 0>; - }; - gpt2: timer@620 { // General Purpose Timer in GPIO mode compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio"; - reg = <0x620 0x10>; - interrupts = <1 11 0>; gpio-controller; #gpio-cells = <2>; }; gpt3: timer@630 { // General Purpose Timer in GPIO mode compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio"; - reg = <0x630 0x10>; - interrupts = <1 12 0>; gpio-controller; #gpio-cells = <2>; }; gpt4: timer@640 { // General Purpose Timer in GPIO mode compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio"; - reg = <0x640 0x10>; - interrupts = <1 13 0>; gpio-controller; #gpio-cells = <2>; }; gpt5: timer@650 { // General Purpose Timer in GPIO mode compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio"; - reg = <0x650 0x10>; - interrupts = <1 14 0>; gpio-controller; #gpio-cells = <2>; }; gpt6: timer@660 { // General Purpose Timer in GPIO mode compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio"; - reg = <0x660 0x10>; - interrupts = <1 15 0>; gpio-controller; #gpio-cells = <2>; }; gpt7: timer@670 { // General Purpose Timer in GPIO mode compatible = "fsl,mpc5200b-gpt-gpio","fsl,mpc5200-gpt-gpio"; - reg = <0x670 0x10>; - interrupts = <1 16 0>; - gpio-controller; - #gpio-cells = <2>; - }; - - rtc@800 { // Real time clock - compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc"; - reg = <0x800 0x100>; - interrupts = <1 5 0 1 6 0>; - }; - - can@900 { - compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; - interrupts = <2 17 0>; - reg = <0x900 0x80>; - }; - - can@980 { - compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; - interrupts = <2 18 0>; - reg = <0x980 0x80>; - }; - - gpio_simple: gpio@b00 { - compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio"; - reg = <0xb00 0x40>; - interrupts = <1 7 0>; gpio-controller; #gpio-cells = <2>; }; - gpio_wkup: gpio@c00 { - compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup"; - reg = <0xc00 0x40>; - interrupts = <1 8 0 0 3 0>; - gpio-controller; - #gpio-cells = <2>; - }; - - spi@f00 { - compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; - reg = <0xf00 0x20>; - interrupts = <2 13 0 2 14 0>; - }; - - usb@1000 { - compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be"; - reg = <0x1000 0xff>; - interrupts = <2 6 0>; - }; - - dma-controller@1200 { - compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm"; - reg = <0x1200 0x80>; - interrupts = <3 0 0 3 1 0 3 2 0 3 3 0 - 3 4 0 3 5 0 3 6 0 3 7 0 - 3 8 0 3 9 0 3 10 0 3 11 0 - 3 12 0 3 13 0 3 14 0 3 15 0>; - }; - - xlb@1f00 { - compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb"; - reg = <0x1f00 0x100>; - }; - psc@2000 { /* PSC1 in ac97 mode */ compatible = "mpc5200b-psc-ac97","fsl,mpc5200b-psc-ac97"; cell-index = <0>; - reg = <0x2000 0x100>; - interrupts = <2 1 0>; }; /* PSC2 port is used by CAN1/2 */ + psc@2200 { + status = "disabled"; + }; psc@2400 { /* PSC3 in UART mode */ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2400 0x100>; - interrupts = <2 3 0>; }; /* PSC4 is ??? */ + psc@2600 { + status = "disabled"; + }; /* PSC5 is ??? */ + psc@2800 { + status = "disabled"; + }; psc@2c00 { /* PSC6 in UART mode */ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2c00 0x100>; - interrupts = <2 4 0>; }; ethernet@3000 { - compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec"; - reg = <0x3000 0x400>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <2 5 0>; phy-handle = <&phy0>; }; mdio@3000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio"; - reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts - interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co. - phy0: ethernet-phy@0 { reg = <0>; }; }; - ata@3a00 { - compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata"; - reg = <0x3a00 0x100>; - interrupts = <2 7 0>; - }; - - i2c@3d00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d00 0x40>; - interrupts = <2 15 0>; - }; - i2c@3d40 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d40 0x40>; - interrupts = <2 16 0>; rtc@51 { compatible = "nxp,pcf8563"; reg = <0x51>; @@ -268,12 +116,6 @@ }; pci@f0000d00 { - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - device_type = "pci"; - compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci"; - reg = <0xf0000d00 0x100>; interrupt-map-mask = <0xf800 0 0 7>; interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot 0xc000 0 0 2 &mpc5200_pic 1 1 3 @@ -284,11 +126,12 @@ 0xc800 0 0 2 &mpc5200_pic 1 2 3 0xc800 0 0 3 &mpc5200_pic 1 3 3 0xc800 0 0 4 &mpc5200_pic 0 0 3>; - clock-frequency = <0>; // From boot loader - interrupts = <2 8 0 2 9 0 2 10 0>; - bus-range = <0 0>; ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000 0x02000000 0 0xa0000000 0xa0000000 0 0x10000000 0x01000000 0 0x00000000 0xb0000000 0 0x01000000>; }; + + localbus { + status = "disabled"; + }; }; diff --git a/arch/powerpc/boot/dts/pcm032.dts b/arch/powerpc/boot/dts/pcm032.dts index 9dee52b6747..1dd478bfff9 100644 --- a/arch/powerpc/boot/dts/pcm032.dts +++ b/arch/powerpc/boot/dts/pcm032.dts @@ -12,99 +12,37 @@ * option) any later version. */ -/dts-v1/; +/include/ "mpc5200b.dtsi" / { model = "phytec,pcm032"; compatible = "phytec,pcm032"; - #address-cells = <1>; - #size-cells = <1>; - interrupt-parent = <&mpc5200_pic>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - PowerPC,5200@0 { - device_type = "cpu"; - reg = <0>; - d-cache-line-size = <32>; - i-cache-line-size = <32>; - d-cache-size = <0x4000>; // L1, 16K - i-cache-size = <0x4000>; // L1, 16K - timebase-frequency = <0>; // from bootloader - bus-frequency = <0>; // from bootloader - clock-frequency = <0>; // from bootloader - }; - }; memory { - device_type = "memory"; reg = <0x00000000 0x08000000>; // 128MB }; soc5200@f0000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc5200b-immr"; - ranges = <0 0xf0000000 0x0000c000>; - bus-frequency = <0>; // from bootloader - system-frequency = <0>; // from bootloader - - cdm@200 { - compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm"; - reg = <0x200 0x38>; - }; - - mpc5200_pic: interrupt-controller@500 { - // 5200 interrupts are encoded into two levels; - interrupt-controller; - #interrupt-cells = <3>; - compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic"; - reg = <0x500 0x80>; - }; - - timer@600 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x600 0x10>; - interrupts = <1 9 0>; + timer@600 { // General Purpose Timer fsl,has-wdt; }; - timer@610 { // General Purpose Timer - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x610 0x10>; - interrupts = <1 10 0>; - }; - gpt2: timer@620 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x620 0x10>; - interrupts = <1 11 0>; gpio-controller; #gpio-cells = <2>; }; gpt3: timer@630 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x630 0x10>; - interrupts = <1 12 0>; gpio-controller; #gpio-cells = <2>; }; gpt4: timer@640 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x640 0x10>; - interrupts = <1 13 0>; gpio-controller; #gpio-cells = <2>; }; gpt5: timer@650 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x650 0x10>; - interrupts = <1 14 0>; gpio-controller; #gpio-cells = <2>; }; @@ -118,138 +56,49 @@ }; gpt7: timer@670 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x670 0x10>; - interrupts = <1 16 0>; gpio-controller; #gpio-cells = <2>; }; - rtc@800 { // Real time clock - compatible = "fsl,mpc5200b-rtc","fsl,mpc5200-rtc"; - reg = <0x800 0x100>; - interrupts = <1 5 0 1 6 0>; - }; - - can@900 { - compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; - interrupts = <2 17 0>; - reg = <0x900 0x80>; - }; - - can@980 { - compatible = "fsl,mpc5200b-mscan","fsl,mpc5200-mscan"; - interrupts = <2 18 0>; - reg = <0x980 0x80>; - }; - - gpio_simple: gpio@b00 { - compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio"; - reg = <0xb00 0x40>; - interrupts = <1 7 0>; - gpio-controller; - #gpio-cells = <2>; - }; - - gpio_wkup: gpio@c00 { - compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup"; - reg = <0xc00 0x40>; - interrupts = <1 8 0 0 3 0>; - gpio-controller; - #gpio-cells = <2>; - }; - - spi@f00 { - compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; - reg = <0xf00 0x20>; - interrupts = <2 13 0 2 14 0>; - }; - - usb@1000 { - compatible = "fsl,mpc5200b-ohci","fsl,mpc5200-ohci","ohci-be"; - reg = <0x1000 0xff>; - interrupts = <2 6 0>; - }; - - dma-controller@1200 { - compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm"; - reg = <0x1200 0x80>; - interrupts = <3 0 0 3 1 0 3 2 0 3 3 0 - 3 4 0 3 5 0 3 6 0 3 7 0 - 3 8 0 3 9 0 3 10 0 3 11 0 - 3 12 0 3 13 0 3 14 0 3 15 0>; - }; - - xlb@1f00 { - compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb"; - reg = <0x1f00 0x100>; - }; - psc@2000 { /* PSC1 is ac97 */ compatible = "fsl,mpc5200b-psc-ac97","fsl,mpc5200-psc-ac97"; cell-index = <0>; - reg = <0x2000 0x100>; - interrupts = <2 1 0>; }; /* PSC2 port is used by CAN1/2 */ + psc@2200 { + status = "disabled"; + }; psc@2400 { /* PSC3 in UART mode */ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2400 0x100>; - interrupts = <2 3 0>; }; /* PSC4 is ??? */ + psc@2600 { + status = "disabled"; + }; /* PSC5 is ??? */ + psc@2800 { + status = "disabled"; + }; psc@2c00 { /* PSC6 in UART mode */ compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2c00 0x100>; - interrupts = <2 4 0>; }; ethernet@3000 { - compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec"; - reg = <0x3000 0x400>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <2 5 0>; phy-handle = <&phy0>; }; mdio@3000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio"; - reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts - interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co. - phy0: ethernet-phy@0 { reg = <0>; }; }; - ata@3a00 { - compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata"; - reg = <0x3a00 0x100>; - interrupts = <2 7 0>; - }; - - i2c@3d00 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d00 0x40>; - interrupts = <2 15 0>; - }; - i2c@3d40 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d40 0x40>; - interrupts = <2 16 0>; rtc@51 { compatible = "nxp,pcf8563"; reg = <0x51>; @@ -260,20 +109,9 @@ pagesize = <32>; }; }; - - sram@8000 { - compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram"; - reg = <0x8000 0x4000>; - }; }; pci@f0000d00 { - #interrupt-cells = <1>; - #size-cells = <2>; - #address-cells = <3>; - device_type = "pci"; - compatible = "fsl,mpc5200b-pci","fsl,mpc5200-pci"; - reg = <0xf0000d00 0x100>; interrupt-map-mask = <0xf800 0 0 7>; interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3 // 1st slot 0xc000 0 0 2 &mpc5200_pic 1 1 3 @@ -284,20 +122,12 @@ 0xc800 0 0 2 &mpc5200_pic 1 2 3 0xc800 0 0 3 &mpc5200_pic 1 3 3 0xc800 0 0 4 &mpc5200_pic 0 0 3>; - clock-frequency = <0>; // From boot loader - interrupts = <2 8 0 2 9 0 2 10 0>; - bus-range = <0 0>; ranges = <0x42000000 0 0x80000000 0x80000000 0 0x20000000 0x02000000 0 0xa0000000 0xa0000000 0 0x10000000 0x01000000 0 0x00000000 0xb0000000 0 0x01000000>; }; localbus { - compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; - - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0xfe000000 0x02000000 1 0 0xfc000000 0x02000000 2 0 0xfbe00000 0x00200000 @@ -350,40 +180,39 @@ bank-width = <2>; }; - /* + /* * example snippets for FPGA * * fpga@3,0 { - * compatible = "fpga_driver"; - * reg = <3 0 0x02000000>; - * bank-width = <4>; + * compatible = "fpga_driver"; + * reg = <3 0 0x02000000>; + * bank-width = <4>; * }; * * fpga@4,0 { - * compatible = "fpga_driver"; - * reg = <4 0 0x02000000>; - * bank-width = <4>; + * compatible = "fpga_driver"; + * reg = <4 0 0x02000000>; + * bank-width = <4>; * }; - */ + */ - /* + /* * example snippets for free chipselects - * + * * device@5,0 { - * compatible = "custom_driver"; - * reg = <5 0 0x02000000>; + * compatible = "custom_driver"; + * reg = <5 0 0x02000000>; * }; - * + * * device@6,0 { - * compatible = "custom_driver"; - * reg = <6 0 0x02000000>; + * compatible = "custom_driver"; + * reg = <6 0 0x02000000>; * }; - * + * * device@7,0 { - * compatible = "custom_driver"; - * reg = <7 0 0x02000000>; + * compatible = "custom_driver"; + * reg = <7 0 0x02000000>; * }; - */ + */ }; }; - diff --git a/arch/powerpc/boot/dts/uc101.dts b/arch/powerpc/boot/dts/uc101.dts index e00441a3e5a..ba83d5488ec 100644 --- a/arch/powerpc/boot/dts/uc101.dts +++ b/arch/powerpc/boot/dts/uc101.dts @@ -11,79 +11,24 @@ * option) any later version. */ -/dts-v1/; +/include/ "mpc5200b.dtsi" / { model = "manroland,uc101"; compatible = "manroland,uc101"; - #address-cells = <1>; - #size-cells = <1>; - interrupt-parent = <&mpc5200_pic>; - - cpus { - #address-cells = <1>; - #size-cells = <0>; - - PowerPC,5200@0 { - device_type = "cpu"; - reg = <0>; - d-cache-line-size = <32>; - i-cache-line-size = <32>; - d-cache-size = <0x4000>; // L1, 16K - i-cache-size = <0x4000>; // L1, 16K - timebase-frequency = <0>; // from bootloader - bus-frequency = <0>; // from bootloader - clock-frequency = <0>; // from bootloader - }; - }; - - memory { - device_type = "memory"; - reg = <0x00000000 0x04000000>; // 64MB - }; soc5200@f0000000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "fsl,mpc5200b-immr"; - ranges = <0 0xf0000000 0x0000c000>; - reg = <0xf0000000 0x00000100>; - bus-frequency = <0>; // from bootloader - system-frequency = <0>; // from bootloader - - cdm@200 { - compatible = "fsl,mpc5200b-cdm","fsl,mpc5200-cdm"; - reg = <0x200 0x38>; - }; - - mpc5200_pic: interrupt-controller@500 { - // 5200 interrupts are encoded into two levels; - interrupt-controller; - #interrupt-cells = <3>; - compatible = "fsl,mpc5200b-pic","fsl,mpc5200-pic"; - reg = <0x500 0x80>; - }; - gpt0: timer@600 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x600 0x10>; - interrupts = <1 9 0>; gpio-controller; #gpio-cells = <2>; }; gpt1: timer@610 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x610 0x10>; - interrupts = <1 10 0>; gpio-controller; #gpio-cells = <2>; }; gpt2: timer@620 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x620 0x10>; - interrupts = <1 11 0>; gpio-controller; #gpio-cells = <2>; }; @@ -97,118 +42,85 @@ }; gpt4: timer@640 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x640 0x10>; - interrupts = <1 13 0>; gpio-controller; #gpio-cells = <2>; }; gpt5: timer@650 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x650 0x10>; - interrupts = <1 14 0>; gpio-controller; #gpio-cells = <2>; }; gpt6: timer@660 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x660 0x10>; - interrupts = <1 15 0>; gpio-controller; #gpio-cells = <2>; }; gpt7: timer@670 { // General Purpose Timer in GPIO mode - compatible = "fsl,mpc5200b-gpt","fsl,mpc5200-gpt"; - reg = <0x670 0x10>; - interrupts = <1 16 0>; gpio-controller; #gpio-cells = <2>; }; - gpio_simple: gpio@b00 { - compatible = "fsl,mpc5200b-gpio","fsl,mpc5200-gpio"; - reg = <0xb00 0x40>; - interrupts = <1 7 0>; - gpio-controller; - #gpio-cells = <2>; + rtc@800 { + status = "disabled"; }; - gpio_wkup: gpio@c00 { - compatible = "fsl,mpc5200b-gpio-wkup","fsl,mpc5200-gpio-wkup"; - reg = <0xc00 0x40>; - interrupts = <1 8 0 0 3 0>; - gpio-controller; - #gpio-cells = <2>; + can@900 { + status = "disabled"; + }; + + can@980 { + status = "disabled"; }; - dma-controller@1200 { - compatible = "fsl,mpc5200b-bestcomm","fsl,mpc5200-bestcomm"; - reg = <0x1200 0x80>; - interrupts = <3 0 0 3 1 0 3 2 0 3 3 0 - 3 4 0 3 5 0 3 6 0 3 7 0 - 3 8 0 3 9 0 3 10 0 3 11 0 - 3 12 0 3 13 0 3 14 0 3 15 0>; + spi@f00 { + status = "disabled"; }; - xlb@1f00 { - compatible = "fsl,mpc5200b-xlb","fsl,mpc5200-xlb"; - reg = <0x1f00 0x100>; + usb@1000 { + status = "disabled"; }; - psc@2000 { /* PSC1 in UART mode */ + psc@2000 { // PSC1 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2000 0x100>; - interrupts = <2 1 0>; }; - psc@2200 { /* PSC2 in UART mode */ + psc@2200 { // PSC2 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2200 0x100>; - interrupts = <2 2 0>; }; - psc@2c00 { /* PSC6 in UART mode */ + psc@2400 { // PSC3 + status = "disabled"; + }; + + psc@2600 { // PSC4 + status = "disabled"; + }; + + psc@2800 { // PSC5 + status = "disabled"; + }; + + psc@2c00 { // PSC6 compatible = "fsl,mpc5200b-psc-uart","fsl,mpc5200-psc-uart"; - reg = <0x2c00 0x100>; - interrupts = <2 4 0>; }; ethernet@3000 { - compatible = "fsl,mpc5200b-fec","fsl,mpc5200-fec"; - reg = <0x3000 0x400>; - local-mac-address = [ 00 00 00 00 00 00 ]; - interrupts = <2 5 0>; phy-handle = <&phy0>; }; mdio@3000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-mdio","fsl,mpc5200-mdio"; - reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts - interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co. - phy0: ethernet-phy@0 { compatible = "intel,lxt971"; reg = <0>; }; }; - ata@3a00 { - compatible = "fsl,mpc5200b-ata","fsl,mpc5200-ata"; - reg = <0x3a00 0x100>; - interrupts = <2 7 0>; + i2c@3d00 { + status = "disabled"; }; i2c@3d40 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; - reg = <0x3d40 0x40>; - interrupts = <2 16 0>; fsl,preserve-clocking; clock-frequency = <400000>; @@ -221,19 +133,13 @@ reg = <0x51>; }; }; + }; - sram@8000 { - compatible = "fsl,mpc5200b-sram","fsl,mpc5200-sram"; - reg = <0x8000 0x4000>; - }; + pci@f0000d00 { + status = "disabled"; }; localbus { - compatible = "fsl,mpc5200b-lpb","fsl,mpc5200-lpb","simple-bus"; - - #address-cells = <2>; - #size-cells = <1>; - ranges = <0 0 0xff800000 0x00800000 1 0 0x80000000 0x00800000 3 0 0x80000000 0x00800000>; -- cgit v1.2.3-70-g09d2